Search Documents

By D. S. Flett, D. W. West

The solvent extraction of chromium 111 has been studied for the system Cr 111, H,SO., H,O/RNH/RNH., xylene, where the primary amine used was Primene JMT. Rate studies have shown that extremely long equilibrium times are required, ranging from 1 hr at 80°C to 20 days at room temperature. Heating the solution prior to extraction increases the rate of extraction. The variation in the amount of Cr 111 extracted is an inverse function of the acidity of the aqueous phase. Thus, the slow rates of extraction appear to be connected with the hydrolysis of the Cr I11 species. Extraction isotherms for the extraction of Cr 111 have been obtained for two sets of experimental conditions, namely at 60°C and for a heat-treated solution cooled to room temperature. The separation of Fe 111 from Cr 111 and Cr 111 from Cu 11 in sulfate solution by extraction with Primene JMT has been studied and shown to be feasible. A survey of the literature relating to the solvent extraction of chromium showed that, although many systems exist for extraction of Cr VI, only a very few reagents have been found to extract Cr 111. The extraction of Cr III by di-(2-ethyl hexyl) phosphoric acid has been reported by Kimura.' A straight-line dependence of slope —2 was observed between log D,, and the log mineral acid concentration at constant extractant concentration. Since the slope of this plot reflects the charge on the ion extracted, it must be concluded that a hydrolyzed species of Cr III is being extracted. Carboxylic acids generally do not form extractable complexes with Cr III but di-isopropyl salicylic acie does extract Cr 111. Simple acid backwashing of the organic phase, however, failed to remove the chromium. Similar difficulty in backwashing was found by Hellwege and Schweitzer8 in the extraction of Cr I11 with acetyl-acetone in chloroform. The extraction of Cr 111 from chloride solutions by alkyl amines has been reported4-' but the maximum amount of extraction achieved in these studies did not exceed 10%: From sulfate solutions, however, Ishimori" has shown that appreciable amounts of Cr I11 were extracted by amines. The amines used were tri-iso-octyl amine, Amberlite LA-1 (a secondary amine, Rohm & Haas) and Primene JMT (primary amine, Rohm & Haas). The efficiency of extraction with regard to amine type was primary>secondary> tertiary. Appreciable extraction of Cr I11 was recorded for Primene JMT as the aqueous phase acidity tended to zero. The major difficulty with Cr I11 in solvent extraction systems stems from the nonlabile nature of the ion in complex formation. This accounts for the slow rate of extraction generally experienced and the difficulty encountered in backwashing the Cr I11 from the organic phase in the case of liquid cation exchangers. Consequently, the possibility of extraction of Cr I11 as a complex anion is attractive since the backwashing problems should be minimized in this way. From published data, it appeared that the extraction of chromium from sulfate solutions of low acidity by primary amines afforded the best chance of success for a useful solvent extraction system for Cr iii This paper presents the results of a study of the extraction of Cr I11 from sulfate solution by Primene JMT and examines the application of such an extraction procedure for the recovery of chromium from liquors containing iron and copper. Experimental Chromium solutions were prepared from chrome alum in sulfuric acid and sodium sulfate so as to maintain a constant concentration of sulfate ion of 1.5 molar. Solutions of Primene JMT were prepared in xylene and the amine equilibrated with sulfuric acid/sodium sul-fate solutions, of the same acidity as the chromium solution, until there was no change in acidity between the initial and final aqueous phases. The solutions of Primene JMT conditioned in this way were then used for the equilibration experiments. Equilibrations at 25°C were carried out in stoppered conical flasks shaken in a thermostat; equilibrations at all other temperatures were carried out in stirred flasks in a thermostat. After equilibration, the phases were separated and analyzed for chromium. In the tests on the rate of extraction, small samples of equal volume of both phases were withdrawn from time to time and the chromium distribution determined. The chromium analyses were carried out either coloi-imetrically using diphenyl carbazide, or volu-metrically using addition of excess standard ferrous ammonium sulfate and back titration of the excess iron with potassium dichromate. The oxidation of Cr 111 to Cr VI in the case of the raffinate solution was effected by boiling with potassium persulfate in the presence of silver nitrate and, for the backwash solution, by boiling with sodium hydroxide and hydrogen peroxide. Results Preliminary experiments indicated that extraction results were effected by the age of the chromium solution, higher distribution coefficients being obtained with solutions which had been allowed to stand for some time. Consequently a stock solution of chrome alum, 10 m moles per 1 Cr I11 in 1.4 M Na,SO,/O.l M &SO,,

Jan 1, 1971

By G. A. Chadwick, D. Jaffrey

The morpho1ogies and orientation relationships of the phases in the Sn-Zn and A1-A13Ni eutectic systems were examined by electron microscopy and X-ray diffraction techniques. In each alloy the "transition" from the lamellar to the fibrous morphology was found to be one of scale, not of type. The minor phase in both systems exhibited certain well developed facets which were not affected by changes in the ingot solidification rate. The crystallographic relationships displayed by the pairs of phases in both systems were also insensitive to the growth rate. In the Sn-Zn alloy, the unique relationship of: growth direction - II [1201 Sn - II [01101 Zn and ribbon interface plane 11 (101) Sn 11 (7012) Zn was determined. The Al-Al3Ni alloy phases did not possess any particular orientation relationship, though the Al3Ni phase invariably grew in the [010] direction and exhibited the same set of facet planes. These results are discussed in relation to current eutectic growth theories and explanations of the "lamellar to fibrous transition". THE lamellar to fibrous transition that occurs in many eutectic alloys has been the subject of considerable speculation and experimental study. In some alloys it can be induced solely by an increase in the solidification rate,'-3 whereas in others the transition supposedly occurs only if the lamellae are forced to grow out of the overall ingot growth direction.4-6 he cause of this latter type of transition has been attributed to deviations of the lamellae from their low energy habit planes;4'5'7 fibers are produced because the sustaining force for lamellar growth (a low energy boundary) is destroyed. Implicit in these explanations is the assumption that fibers are circular in cross-section and completely lacking in low energy inter-phase interfaces. The "natural" growth rate dependent transition has been studied less thoroughly although Tiller8 has attempted a theoretical explanation of it. Tiller's arguments are not completely satisfactory9 but his suggestion that the relative undercoolings of the solid/liquid interface for lamellar and fibrous morphologies are growth rate dependent cannot be totally discounted; it is possible, for instance, that the relative interfacial undercoolings could alter and produce the observed morphology change if the orientation relationships between the phases and the associated interphase bound- ary energies were sensitive to growth rate. Salkind et al." have reported finding a change in the orientation relationships in the A1-A13Ni system accompanying the lamellar to fibrous transition, but contradictory evidence has also been reported for this3'" and another system,12 so the position remains unclear. In an attempt to clarify matters a study was made of the "lamellar to fibrous" transition in the Sn-Zn and A1-A13Ni eutectic systems; the morphologies of these two selected systems are quite similar when viewed by optical microscopy. In the present research the morphologies and morphology changes were investigated by electron microscopy. The orientation relationships existing between the eutectic phases were also determined for both morphologies in both eutectic systems. EXPERIMENTAL PROCEDURE The materials and method of alloy preparation and ingot solidification for the Sn-Zn system have been reported previously.2 In this investigation nine horizontally grown ingots of the highest purity (99.9997 pct) were used. The temperature gradient in the melt was not intentionally varied and was approximately 10°C per cm. Seven growth rates between 1.3 cm per hr and 20 cm per hr were imposed. The A1-A13Ni alloys were prepared from "Spec. Pure" nickel and 99.995 pct aluminum by melting the components in an open alumina crucible and casting the melt into the cold graphite mold. Six ingots of the Al-Al3Ni alloy were unidirectionally solidified at growth rates from 1 cm per hr to 12 cm per hr under high purity argon. A typical ingot was 20 cm long, 1 cm wide, and 0.75 cm to 1.5 cm thick. Samples taken from the bars at positions 12 cm from the nucleation end were examined by conventional orthogonal-section metallo-graphic techniques. When required, samples were mounted for X-ray diffraction analysis using the Laue back-reflection technique with a finely focussed X-ray source. The surfaces of the A1-A13Ni specimens were prepared by mechanically polishing them down to the 1 µ diamond pad stage followed by an electropolish in 80/20 methanol/perchloric acid solution at 0°C and 20 to 30 v. The Sn-Zn specimens were repeatedly polished on an alumina pad and etched in hot dilute (2 pct) nitric acid until the diffraction spots were found to be sharp. Thin films of the alloys were prepared for observation in an electron microscope by spark machining thin discs (0.03 to 0.04 in. thick) from longitudinal and lateral sections of the bars and elec-trolytically thinning them via a jet polishing technique. For the A1-A13Ni eutectic alloy, an 80/20 mixture of ethanol/perchloric acid at 40 v and 20°C was found to be satisfactory. A solution of 70/20/10 methanol/perchloric acid/butylcellosolve at 25 v and 20°C was used on the Sn-Zn alloy. For the former alloy the jet nozzles (cathodes) and the disc clamps were of aluminum;

Jan 1, 1970

By A. E. Lillstrom

IN the development of iron mines and production of iron ore from the Marquette range, drilling blast-holes is an important phase of the mining cycle. The ground drilled in ore production can be classified into two main categories, soft hematite and hard hematite or magnetite. Within these categories the material exhibits a wide range of penetrability by percussion drills. Development work encounters various types of rock. Slate and altered basic intrusives constitute the softer types commonly encountered. Harder materials are represented mainly by greywacke, quartzite, iron formation, and diorite. Prior to the first tungsten carbide trials in late 1947 and early 1948, hard-rock and ore drilling was done with steel jackbits starting at 21/4-in. diam. These were reconditioned by hot milling. Automatic or handcrank 31/2-in. drifters were employed, mounted on Jumbos, posts and arms, or tripods, depending upon the working place. With the exception of shaft sinking jobs where 55-lb sinker machines were and still are used with 1-in. quarter octagon steel, the other production and development mining utilized 11/4-in. round and Leyner-lugged steel. The following properties have been selected as typical examples wherein carbide bit applications have proved economical. The Mather mine "A" and "B" shafts and Cleveland-Cliffs Iron Co. mines are soft ore mines where insert bits are used in rock development only. The Greenwood mine, Inland Steel Co., Champion mine, North Range Mining Co., and Cliffs shaft mine, Cleveland-Cliffs Iron Co., are hard ore mines where all drilling is done with tungsten carbide bits. Mother Mine "A" Shaft In the Mather mine "A" shaft and other soft ore properties where only rock development work is done with the tungsten carbide bits, several types and makes of bits have been tried since early 1948. The greatest proportion of failures have been at the connection end, although the early trials with the 13 Series Carset 11/2-in. bit used in conjunction with 31/2 -in. automatic-feed drifters, showed an equal amount of shattered inserts. To combat this shattering, the 31/2 -in. drifters were replaced by 3-in. drifters, thus eliminating, for the most part, insert failures. However, the attachment end of the rod continued to be the main source of trouble. The greatest amount of failure was in the stud or at the upset section approximately 2 in. behind the drive shoulder of the rod. Heat treatment was changed several times as well as the composition of the alloy studs. Since this failed to correct the trouble, a decision was made to change to a heavier attachment section. Timken 11/2-in., type M, bits were then employed and showed an exceptional improvement. The rods are discarded when the thread contour shows sharpening or wear on the shoulder. It was also learned that the Timken insert did not show as rapid gage and cutting edge wear as did competitive makes, and footage per use increased by approximately 50 pct. Prior to the Timken trials the average life per bit at the Mather mine "A" shaft on 6-ft change chain-feed drifters was 500 ft, and the rod life at the connection end was 50 ft. The Timken bit with chrome-plated thread averaged 1200 ft, and rod life increased to as much as 500 ft. However, the life of the connection end was much better on shorter length drill rods or in places where machines with 34-in. change were used. The bit thread continued to be the point of ultimate failure with thread strippage, constituting the cause for discard of bits. In one of the new development headings, harder rock was encountered for approximately 800 ft, dropping the life per bit to a low of 90 ft with shank and thread life of rods dropping to approximately 125 ft average. The stripped bits were then welded to the rods, increasing the life per bit by 75 to 100 pct. The rod transportation for main level development was not a problem so intraset rods were tried. Intraset rods have tungsten carbide inserts set into the rods proper by the manufacturer and can be obtained with chisel or four point bits. This type of rod eliminates the need for any connection and the steel being a special alloy will show more feet drilled per rod. The first trial was made with eight rods, and final results averaged 350 ft per rod, six of the rods worked the life of the bit end, and two broke shanks at less than 50 ft. The preceding example showed a considerable improvement, so additional steel of the same type was purchased, but its use has been limited to main level drifting only, because of the handling problem involved in transportation of the complete rod to mine shops for resharpening. Further trials are being made on improving the life per detachable bit by chrome plating. To date, the chrome plating shows an improvement of approximately 100 pct. However, final results will not be known until the present long term trials have been completed. Mother Mine "B" Shaft In November 1947, tungsten carbide bits were first tried at the Mather mine "B" shaft. The use of 1%-in. Carset 13 Series bits, for drilling the 72-hole, 7-ft shaft round, decreased the drilling time from an average of 41/2 hr per round required with steel bits, to 2 hr with insert bits. The best drilling time for

Jan 1, 1952

By H. T. Green, R. M. Brick

True stress-strain data on alloys of pure iron with up to 2.4 pct Al were obtained in the temperature range +100° to —185°C. Alumi-num was found to reduce yield and flow stresses of iron at low temperatures but to have little or no effect on ductility. The effects of temperature and composition on strain hardening are discussed. SEVERAL independent studies of the behavior of high purity iron binary alloys at low temperatures are now in progress in attempts to evaluate systematically the variables affecting the low temperature brittleness of ferritic steels. This paper reports the results of one such investigation in which the tensile properties of aluminum and aluminum plus silicon ferrites were measured from 100" to —192°C. True stress-natural strain data have been obtained in order to evaluate as many as possible of the parameters which describe the behavior of the materials involved. In comparable studies at the National Physical Laboratory in England, iron and iron alloys of high purity have been produced' and tested at subat-mospheric temperatures.' True stress-natural strain curves were obtained there also. The purest iron contained 0.0025 pct C and 0.001 pct O and N. Even this, as normalized at 950°C following hot rolling, showed little ductility at -196°C. The grain size was ASTM No. 3, and the room-temperature yield strength was 17,800 psi (which seems too high for pure iron). Some of the NPL irons contained considerably more oxygen and demonstrated intergran-ular fracture at —196°C. The authors2 carefully differentiated between intergranular fractures associated with excessive oxygen content and transcrys-talline cleavage with little ductility encountered at —196°C in the purer material. The cleavage stress was half again as great as that associated with inter-granular fracture. Test Material, Preparation, and Procedures Of a number of Fe-A1 alloys produced, eight were considered to be sufficiently pure for testing. Partial chemical analyses (Table I), low observed yield points, and high ductilities indicate these alloys to be comparatively pure for vacuum-melted irons of sizable ingots, 5 Ib or more. To produce the binary Fe-A1 alloys, electrolytic iron was melted in air, cast into slabs, and rolled to strips 0.010 in. thick. These strips, joined into a continuous ribbon and wound into 2 1/2 in. diameter spools, were subjected for four weeks to a moving atmosphere of purified dry hydrogen in a stainless-steel tube at 1050" to 1150°C. Charges of these spools were melted in beryllia crucibles under good vacuums (1 micron), and aluminum (99.97 pct Al) was added to the melts. Compositions of these alloys are recorded in Table I. The ingots were hot forged and then cold rolled at least 65 pct to 3/8 in. rods which were vacuum annealed to the desired grain size, approximately ASTM No. 4, prior to machining into tensile test bars. All tensile specimens had gage sections 1 in. long, with a fillet of 1.5 in. radius to the shoulder. Gage diameters were 0.250 in, except for a few rods where additional cold work required use of a 0.200 in. gage section. After machining, 0.002 in. was removed from the gage diameter using 240, 400, and 600-grit metallo-graphic papers. The final polish with 600 grit left the fine scratches running in the longitudinal direction. By this means, surface metal strained during machining was removed. A few specimens heat treated after machining were similarly reduced 0.004 in. to remove any material affected chemically by the atmosphere during heat treatments, as is discussed in a later section. Tensile tests of the eight alloys at constant temperatures from +100° to —185°C were performed in apparatus which has been described." The essentials include a double-walled insulated metal vessel which contained the liquid heat-transfer medium surrounding the test specimen. A constant temperature was maintained by means of a pyrometer which regulated the pressure of dry air driving liquid air through a copper coil. Temperature variation was less than ±2°C during a specific test. For axial straining, two lengths of case-hardened chain, terminating in simple shackles, loaded the specimen through threaded grips. The lower grip bar passed through a hole in the bottom of the test vessel to which it was joined by a thin-walled

Jan 1, 1955

By E. Miller, J. M. Eldridge, K. L. Komarek

The liquidus curve of the Mg-Pb system was accurately redetermined. The compound Mg2Pb decomposes peritectically at 538.2° ± 0.3°C to liquid and to a compound p' which melts congruently at 35.0 at. pct Pb and 549.0° ± 0.3°C. The solidus curve of ß' was determined. X-ray diffraction studies indicate that 4' has an orthorhombic structure. Activity values of magnesium calculated from the phase diagram agree with those published in the literature. EXPERIMENTAL thermodynamic properties of binary metallic systems have to be consistent with values calculated from the phase diagram. In systems forming intermetallic compounds the shape of the liquidus curve near a compound is determined by the thermodynamic properties of the coexisting solid and liquid phases. Hauffe and Wagner' neglected the temperature dependence of the chemical potentials and obtained the potential differences of the components of the liquid alloys, relative to stoichiometric liquid. Their calculations were based on the liquidus curve and on the heat of fusion of the compound, and were only valid near the congruent melting point. Steiner, Miller, and Komarek2 developed equations which account for the temperature dependence and obtained the chemical potentials of liquid Mg-Sn alloys over the entire phase diagram from the liquidus and solidus curves and from enthalpy values with the pure components as the standard states. The Mg-Pb phase diagram has been studied by several investigators whose results have been compiled and critically evaluated by Hansen.3 Although the liquidus curve was poorly defined, the general features of the diagram, i.e., one congruent melting compound, Mg2Pb, of essentially stoichiometric composition, two eutectics, and limited terminal solid solubilities, seemed to be suitable for a similar thermodynamic analysis. A careful redeter-mination of the liquidus by thermal analysis revealed, however, the existence of another compound. The liquidus curve between the two eutectics was precisely delineated and the structure and solidus curve of the new compound were investigated. The revised phase diagram was thermodynamic ally analyzed to evaluate the activity of magnesium in the liquid alloys. EXPERIMENTAL PROCEDURE The magnesium metal (Dominion Magnesium Ltd., Toronto, Canada) had a purity of 99.99+ pct; lead (American Smelting and Refining Co.) contained 99.999 pct Pb. Most experiments were carried out in graphite crucibles. Several experiments were made in high-purity alumina (Triangle R.R., Mor-ganite, Inc.) and in Armco iron crucibles to test the inertness of the graphite crucibles. Chemical analysis of magnesium and detailed description of the procedure for thermal analysis have been given previously. For the determination of the solidus curve of the compounds, specimens of initial composition Mg2Pb were equilibrated in a closed isothermal system with magnesium vapor. The source of the magnesium vapor was an alloy which had a gross composition lying in the 0' + L field at the temperature of equilibration. As equilibrium was approached, the specimens lost magnesium to the two-phase reservoir thereby lowering the activity of magnesium in the specimens until activity and composition equaled that of the ß'/ß' + L boundary. Crucibles (1.9 cm ID by 2.2 cm OD by 4.1 cm high) and tightly fitting lids were machined from a molybdenum rod; small, shallow trays were fashioned from thin (0.005 in.) molybdenum sheet, and all the molybdenum components were degreased in hot carbon tetrachloride and then dried. The pieces were then degassed in vacuum at 950°C for about 6 hr. The two-phase alloy was placed at the bottom of the crucible and small specimens of the Mg2Pb compound, weighed on an analytical balance, were placed in two molybdenum trays above the two-phase alloy. The crucible was closed by forcing its lid on and then inserted in a titanium crucible. This crucible was evacuated, flushed twice with argon, and welded under argon. The specimens were equilibrated for about 1 week in a resistance furnace regulated by a Celectray controller, and the runs were terminated by water quenching. The specimens were again weighed and the equilibrium compositions were calculated on the basis that the weight losses were solely due to a loss of magnesium to the two-phase alloy. The structure of the B' phase was investigated by the Debye-Scherrer X-ray diffraction technique. Selected ingots from thermal-analysis experiments containing about 35 at. pct Pb were re-melted, slowly cooled, and crushed in an argon-filled glovebox until the entire ingot passed through a 50-mesh sieve. The powder was thoroughly

Jan 1, 1965

By C. H. Li, R. J. Stokes

This paper compares the fracture behavior of tungsten rods in three conditions: recrystallized. recovered, and wrought. Notched specimens suhjected to a 50 in.-lb impact load showed ductile-brittle transitions at 700, 4.90°, and 440°C, respectinely. The recrystallized material had an equiaxed pain structure and jracbred by simple cleavage from a grain boundary source at all temperatures up to 700°C. The wrought and recovered material had an elongated fibrous structure and at low temperatures fractured by cleavage originating from the notch. As the transition temperature was approached cleavage was preceeded by more and more intergvanular splitting which deflected the crack front into planes parallel to the tensile axis. The enhanced toughness of wrought and recovered tungsten was attributed both to its inability to initiate cleavage because no pain boundaries were suitably oriented perpendicular to the tensile stress and to its inability to maintain cleavage because of intergranular splitting ahead of the crack. It has been appreciated for a long time in a qualitative manner that the room-temperature brittleness of fully recrystallized tungsten may be alleviated by working the material at relatively low temperatures.' More recently this difference in mechanical behavior between wrought and recrystallized tungsten has been examined quantitatively by measurement of the tensile properties as a function of temperature. In these experiments brittleness has been expressed in terms of ductility or reduction in cross-sectional area upon tensile fracture or in terms of the bend radius before fracture under bending.' This work has shown the existence of a fairly sharp transition from brittle to ductile behavior with an increase in temperature. The ductile-brittle transition temperature for recrystallized material is approximately 200°C higher than for wrought material. An increase in strain rate, small additions of impurity,' or an increase in grain size4 shift the respective transition temperatures to higher values, but the difference between them remains approximately the same at 200°C. A number of explanations for this embrittlement by recrystallization have been given. It has been blamed either on the concentration of impurity at the grain boundaries, the increase in grain size, or the change in texture which occurs upon recrystallization. The present paper examines the effect of different heat treatments on the notch-impact behavior of commercial powder-metallurgy tungsten rods. The change in the ductile-brittle transition temperature for this method of loading and the fracture mode has been related to the different mi-crostructures produced by heat treatment. EXPERIMENTAL PROCEDURE Commercial swaged powder-metallurgy tungsten rods 1-3/8 in. in length and 1/8 in. in diameter were machined to introduce a sharp V notch 0.030 in. deep. To change the microstructure from that of the as-received wrought material some of the specimens were subjected to an anneal in nitrogen either at 1300° or 1400°C for 8 hr or at 1600° or 2000°C for 1/2 hr. The notched rods were then placed in a miniature Charpy-type impact machine and struck at their midpoint (opposite the notch) with a hammer designed to deliver 50 in.-lbs of energy. The strain rate at the base of the notch was estimated to be approximately 100 sec-1 at the instant of impact. The specimens were heated in situ to the desired impact temperature. The microstructures produced by the various anneals were studied by both X-ray diffraction and metallographic techniques. Fig. 1 reproduces the microstructures observed metallographically following a 10-sec electroetch in a 10 pct KOH solution. Fig. l(a) shows the elongated fibrous grain structure of the as-received material. Following the anneal at 1300" or 1400°C the grain structure was still elongated as shown in Fig. l(b) but the etch pits delineated dense polygonized dislocation arrays within many of the grains. Occasionally a relatively dislocation-free recrystallized grain was found growing into the matrix. The anneals at 1600° and 2000°C resulted in complete recrystallization and some grain growth. The grains produced at 1600°C were still slightly elongated as shown in Fig. l(c) whereas the anneal at 2000°C produced equiaxed grains. The changes in grain size produced the expected changes in the X-ray back-reflection patterns; there was no indication either in the as-received material or the annealed material of any preferred orientation. RESULTS a) Impact Behavior. Fig. 2 reproduces the ductile-brittle transition curves measured in the manner described in the previous section. It can be seen that under these testing conditions the as-received

Jan 1, 1964

By George A. Roberts

The development of an alloy system, high-speed steel, is used as an example of the progress of physical metallurgy. Tracing the history of men and their thoughts as they studied and invented and modified these materials, the story of high-speed steel since the 1890's is seen to be a long, slow, but steady progression of achievements. Today's multiplicity of high-speed steels are the result. Data are presented on quantitative metallography of carbides in high-speed steel with high vanadium content using the QTM instrument. Grindability as well as mechanical properties are related to the content of excess MC and M6C carbides in a series of high-speed steels and the newer matrix steels. These emphasize the present state of knowledge and show the current stages of thought that may affect the development in succeeding years. It is a great thrill for me, an ex-research metallurgist and ex-practicing metallurgical engineer, to speak to an audience currently engaged in both pursuits on the occasion of the 43rd Howe Memorial Lecture before the Iron and Steel Division of the AIME. I shall not review Henry Marion Howe's distinguished career, so adequately reviewed in Maxwell Gensamer's contribution in the 1965 AIME History of Metallurgy, except to point out that, while leading the life of an intellectual, he worked as a practicing research metallurgist and a practicing metallurgical engineer for significant periods of time and contributed greatly in both areas. For those of you who believe, as I do, that in the intellectual activity of metallurgy we are blessed with an intimate mixture of science and engineering (see Mehl's 1960 Howe Lecture), we might recall that Howe, while pursuing a life of writing and teaching in later years, served as the first Chairman of the Division of Engineering of the National Academy of Sciences. That metallurgists were called upon then to lead an engineering recognition movement is perhaps related to the strong part played by the AIME and its members in the recent establishment of a National Academy of Engineering and to the fact that a metallurgist is its head, 47 years after Howe served. I stress these engineering aspects for I wish to talk about a metallurgical engineering subject today. Alloy systems, physical metallurgy, and steel blended with an historical perspective and a report on new techniques to improve the old will, I trust, be of sufficient interest to bring these lectures back to the physical-metallurgy banner from which they have departed for 4 years. Those process metallurgists, open-hearth fiends, and physical chemists among you will just have to be patient. The development of an alloy system is the engineering application of scientific thought and fact. There are many interesting alloy systems, developed to a high degree of technology and sophistication over the past 40 to 70 years. These systems are bound together and related by a similar set of characteristics. For example, stainless steels are a system in which the members are related by a high chromium content which gives a corrosion-resistant characteristic. A subfamily in this system would be austenitic steels

Jan 1, 1967

By Charles C. Fatino, Joel S. Hirschhorn

Loose compacts of strained and annealed stainless-steel powders were sintered at various temperatures and times to determine the effect of residual strains on the sintering behavior. The atomized powders were prepared by annealing, ball milling, and rean-nealing. The residual strains and domain size were determined by a Fourier analysis of X-ray diffvaction dala. The specimens were prepared by siwzultaneously sintering cylinders of both strained and unstrained powder. The evaluation of the sintered compacts included density measurements, metallographic examinations, and analyses of X- ray diffraction data. The results of these studies reveal a definite increase in sintered density and sintering rate for the strained powders. THE pressure compacting of metal powders causes deformation of the particles, mechanical interlocking, and increased contact area. After the deformation, severe residual strains remain in these particles. The subsequent contributions of these strains to the sintering process have been considered to be negligible, since the recovery and recrystallization temperatures usually occur prior to the temperature required for the sintering process. Sintering is con-sidered to be the process by which the powders are transformed into solid compacts at temperatures below their melting points. The sintering operation for stainless steel usually takes place in the range of 2050" to 2400°F (0.84 to 0.95 T,, where T, is the absolute melting point or liquidus temperature) while the temperature required for recovery is approximately 1800°F (0.75 T,). However, it has been shown for several metal powders that densification becomes significant in the range of 0.35 to 0.45 T,.' It is the purpose of this study to determine what effect residual strains have upon the sintering behavior of stainless-steel compacts. Loose compacts were selected for study in order to isolate the strain contributions and eliminate the variables inherent in sintering of pressure-formed compacts. Additional variables were minimized by using only one mesh size, one composition, one particle shape, and also by simultaneously sintering both types of powder. Very little work has been carried out previous to the present study to delineate the effect of strains on sintering behavior. Lenel et 01.2 observed that residual stresses in copper compacts caused shrinkage at comparatively low temperatures. Delisle3 loose-sintered ball-milled electrolytic iron and observed that bonding among particles began at a lower temperature as compared to the behavior of annealed powder. Increased densification of ball-milled oxide powders has also been noted.4'5 EXPERIMENTAL PROCEDURES Powder Preparation. The powder used for this study was a commercial-type 316L stainless steel made by the atomization process. A typical chemical analysis is: C- 0.025 pct Mo- 2.2 pct Cr-18.6 pct Ni-12.5 pct Fe—Balance The atomizing process is essentially the rapid freezing of liquid droplets. This nonequilibrium cooling causes coring to occur and two distinct phases are present within the solid particle, the austenitic phase and the ferritic phase. Due to the presence of this ferritic phase, the particles tended to fracture as well as become cold-worked during the subsequent ball-milling operation. (It was also found that this type of cooling produced a broadened and shifted

Jan 1, 1968

By M. S. Burton, J. E. Ritter

The sessile-drop technique was employed to study the effect of atmosphere and alloy additions of titanium and chromium on the surface tension and contact angle of nickel on sapphire substrates at 1500oC. Shear tests were conducted on the solidified sessile drops. The liquid-gas surface tension of pure nickel on sapphire was found to be 1747 ergs per sq cm, with a contact angle of 109.6 deg. The surface tension and contact angle were not affected significantly by the four atmospheres, vacuum, impure argon, pure argon, and pure hydrogen. Small additions of titanium and chromium decreased the contact angle and for the same alloy content, contact angles were lower in pure argon than in pure hydrogen. On the basis of shear-test results , the most probable cause for adhesion in the Ni-Al2O system is the formation of NiO:Al2O3 spinel at the interface; in the titanium alloy-Al2O3 system adhesion is thought to be due to a mechanical interlocking effect; in the chromium alloy-Al2O3 system adhesion is believed to be the result of solid-solution formation involving Cr2O3 and Al2O3 at the interface. In the last few years there has been considerable interest in reinforcing metals with ceramic whiskers. It has been postulated that, by reinforcing nickel with sapphire whiskers, high-temperature strengths su- perior to those of the best current nickel alloys can be achieved.' To fabricate a whisker-metal composite having optimum density and strength, understanding of wettability and adherence in the system is of prime importance. Although there has been some previous research in this a a need for further studies has been cited4-8 to understand better the effects of impurities, alloys additions, and atmosphere on the wetting and bonding of metals to metal oxides. The purpose of this research was to investigate the factors involved in the wetting and adherence of nickel/nickel alloys to sapphire (single-crystal a Al2O3). Sessile-drop experiments were conducted in vacuum, impure argon, pure argon, and pure hydrogen, to determine the effect of atmosphere on the contact angle of the metals on sapphire, and the liquid-gas surface tension of pure nickel. The solidified sessile drops were sheared from the sapphire substrate to measure the bond strength between the metal and ceramic. The alloy additions chosen were titanium and chromium since both enhance the wetting of nickel on sapphire.2, 3c Also, titanium is commonly used when brazing metal-to-ceramic seals to improve adherence. Since chromium forms an oxide that is completely soluble in sapphire, it was thought that the oxide could serve as a transition phase to promote bonding between the Ni-Cr alloy and sapphire. I) EXPERIMENTAL APPARATUS AND PROCEDURE The sessile-drop apparatus was a horizontal furnace, with an induction-heated, cylindrical molybdenum susceptor in a water-cooled Pyrex chamber. This apparatus was patterned after that of Williams and Nielsen.7 A flat Pyrex window at each end of the furnace allowed temperature measurements to be made at one

Jan 1, 1968

By Bernt Ellingsaeter, Terkel Rosenqvist

IN the silicothermic reduction of magnesia, burned dolomite is treated with high grade ferrosilicon in an evacuated steel retort at temperatures between 1150° and 1200°C. The following reaction is assumed to occur MgO + CaO + 1/2 Si (Fe) - Mg(g) +- & Ca,SiO, + Fe with the equilibrium constant on the basis of thermodynamic data for the substances involved and assuming unit activity for all solid constituents, Kubaschewski and Evans' calculated the magnesium pressure as a function of temperature logp,, (mmHg) = 15.06-1.61 T- log T- 13,16O/T. Pidgeon and King," who measured the magnesium pressure by means of a flow method, found values about three times the calculated ones. This may be caused by uncertainties in the thermodynamic data, but may also be caused by the formation of other reaction products, such as Ca,SiO,, which is known to be the stable silicate in equilibrium with lime. Whatever the exact reaction may be, it is evident that as long as all other factors are maintained constant the magnesium pressure will vary with the silicon activity, viz: p,, = &,. (p,,) ", where (p,,)" is the magnesium pressure by the reduction with silicon of unit activity. In the present investigation, p,,, was therefore measured for various grades of ferrosilicon and their silicon activities were calculated. The experimental method was similar to that used by Pidgeon and King. Briquettes of burned dolomite and Fe-Si alloys were placed in a 1 in. heat resistant steel tube and were heated to 1200°C. By means of a flow of purified hydrogen, the magnesium vapor was swept into a condenser filled with steel wool. From the amounts of hydrogen used and magnesium condensed the magnesium partial pressure was calculated. First a tube of 28 pct Cr steel, and later a tube of Kanthal D (a ferrous alloy with 22.6 pct Cr, 2 pct Co, and 4.5 pct Al), was used as a heat resistant tube. The latter tube showed the best heat resistance. The dolomite used had the following composition: 43.6 pct MgO, 55.5 pct CaO, 0.2 pct K,O + NalO, 0.2 pct Fe,O,, and 0.3 pct insoluble. The ferrosilicons were prepared from 98 pct Si of technical grade (0.7 pct Al, 0.3 pct Ca, and 1 pct Fe) by melting with various amounts of electrolytic iron of high purity. The alloys thus obtained were analyzed on their iron and silicon contents, which added up to between 99 and 100 pct. The amounts of reactants were chosen so that there would always be an excess of the oxides, and the average decrease in silicon content during the experiments would be about 1 pct. Most of the reaction occurred in the part of the reaction mixture facing the gas flow. The change in the silicon concentration in the part facing the condenser was, therefore, negligible. To facilitate the reaction, about 1 pct fluorspar was added to the briquette mixture. Fluorspar does not enter the reaction, but is known to act as a

Jan 1, 1957

By R. J. Bethancourt, D. M. Collingwood

The use: of a pilot waterflood is very desirable where all of the pertinent data necessary to initiate a full scale waterflood are not. available. This paper attempts to take a specific case and .show the step by step process of starting with a pilot waterflood and progressing to a full wale flood as results are obtained. INTRODUCTION Many of the older fields of Soutlwest Texas are approaching depletion by primary produrtion methods. As primary protlllc:inp operations on individual properties approach their economic limit. conflicting considerations face management: cm the one hand. plugging and abandonment of wells for equipment salvage; on the other hand, further investment in secondary recovery installtions, equilent, and well workovers in the interests of conservation anal additional oil reserves. In main instances, where primary production by pressure depletion and gas solution drive has been comparatively good, there still exists the possibility of an economic secondary recovery by waterflood. This is not necessarily true to the same degrre of all such fields. nor all portions of large fields. To properly evaluate the economics of a prospective water-11ot1cI requires a considerable amount of precise geological. statitical. and physical data Such information on the older field.; is often very limited. and in the case of the property discussed in this paper was considered inadequate to justify investment in an overall waterflood. Primary production was estimated at :39 per cent of the original oil in place, yet sand conditions of permeability and homogeneity, and position in the field appeared to be favorable for a limited margin of profit from a carefully controlled waterflood. Thus a pilot waterflood, with its minimum initial financial risk, followed by extension as favorable results were obtained, seemed to be the answer for the Sun Oil Co L. Wiederkehr lease in the Nortl Government Wells Field, Duval County. Texas DESCRIPTION OF RESERVOIR Approxinately 8,200 wells have been drilled in Duval County. As of March 1, 1952, there were 3,350 producing oil wells in 92 different fields, with very few flowing wells (Fig. 1.) Sun Oil Co. operates the I.. Wiederkehr lease located in the North Government Wells Field in Duval Countv. 85 mile. west of Corpus Chriti and 100 miles south of San Antonio. The lease has been subjected in part to a controlled five spot waterflood. The North Government Wells Field is roughly 7 miles long and 3 miles wide, with numerous overlapping producing zones. The L. Wiederkehr lease of 3.085 acres. Has seven producing zones from 700 to 7.500 ft. The lease is in the northern section of the field where it is widest, and has 710 acres productive from the North Government Wells .and. (Fig. 2.) The North Government Wells sand, Jackson group. Eocene age, at an average depth of 2.250 ft (minus 1.750 subsea). has a thickness range of 25 ft on the east side of the L. Wiederkehr lease to 4 ft on the west side. It has a slight overall dip to the North and East of some 33 ft to the mile.

Jan 1, 1953

By I. E. Campbell, R. I. Jaffe

Oxygen, nitrogen, and hydrogen are known to be absorbed by titanium at elevated temperatures. Ehrlichl reports that about 30 at. pct oxygen can be dissolved in solid solution by alpha-titanium. Nitrogen also has a solid solubility in alpha-titanium, but there is no information as to its extent. The solid solubility of hydrogen in titanium also is high. Kirshfeld and Sieverts2 report 50 at. pct soluble, while Hägg3 reports about 33 at. pct hydrogen to be soluble in alpha-titanium. General statements are made in the literature that oxygen, nitrogen, and hydrogen embrittle titanium, but no quantitative measurements have been made of the effect of these gases on the mechanical properties of the metal. One reason for this is the lack of a source of titanium pure enough to be considered a suitable starting material. Iodide-refined titanium, made by thermal decomposition of titanium iodide vapor on an incandescent wire,4 contains small amounts of carbon, silicon, iron, and aluminum, but is very low in oxygen, nitrogen, and hydrogen content, and, therefore, was used in this work. A further reason for the lack of quantitative information on the effect of these gases, particularly oxygen, is the difficulty of carrying out accurate analytical determinations at the low concentrations of interest in this work. For this reason, the oxygen, nitrogen, and hydrogen were added in measured amounts as gases, and diffused into the titanium, to avoid the necessity of chemical analysis. The purpose of the work reported here was to isolate and measure the effects of oxygen, nitrogen, and hydrogen on titanium of the highest purity available at the time. The concentrations studied were 0.25, 0.5, and 1 at. pct in each case. Experimental Work One-half of a 24-in. hairpin of iodide-refined titanium was available for this work. The rod was approximately 0.25-in. in diam and had a 0.003-in.tung sten core. From chemical and spectro-graphic analyses, the purity of the sample was estimated to be between 99.80 and 99.95 wt pct. The chief impurities (aside from the tungsten core) were iron (0.04 pct), silicon (0.01-0.1 pct), aluminum (0.05 pct), carbon (0.03 pct). The tungsten core constituted 0.05 pct by weight of the sample. Although some alloying undoubtedly took place between the tungsten and the titanium during the deposition reaction, the core remained substantially intact in the deposited metal. The initial average hardness of the titanium as deposited was 105 Vickers (10-kg load). The maximum hardness was 116 Vickers and the minimum 91 Vickers. The metal was somewhat harder than that currently being obtained by the iodide process, that is, 75-90 Vickers. The rod was cold swaged to ¼-in. diam and then cold rolled in diamond shaped rolls to about 0.080-in. square, using reductions of 15 pct in area per pass. The 0.080-in.-square wire was cut into 6-in. lengths for the preparation of the alloys by the gaseous absorption and diffusion method. ADDITION OF OXYGEN, NITROGEN, AND HYDROGEN TO TITANIUM A modified Sieverts' absorption apparatus, shown in Fig 1, was used in

Jan 1, 1950

By M. J. Pool, P. J. Spencer

Using liquid tin as the solvent metal, the heats of solution of silver and gold in dilute Ag-Au-Sn alloys have been determined at 723°K by solution calorimetry. From the values obtained, the various enthalpy interaction coefficients in the liquid solutions have been calculated. The self-interaction coefficients Au and Ag values of 2413 and -6322 cal per g-atom in binary Au-Sn and Ag-Sn alloys, respectively. For an alloy containing 0.04 mole fraction Ag, Au is equal to 2443 cal per g-atom, and in an alloy containing 0.04 mole fraction Au, Ag has a value of —8883 cal per g-atom. Ag Au has been determined as —2650 cal per g-atom. ADDITION of a second solute to a dilute binary alloy may cause striking changes in the thermodynamic characteristics of the alloy. As yet, such influences cannot be reliably predicted and it is only by accumulation and critical assessment of data that definite patterns can be established. Solute interactions in dilute solutions were first treated mathematically by Wagner,1 who derived expressions for the Gibbs energy interaction coefficients. For an alloy consisting of. two dilute solutes, i and j, in a solvent s, these coefficients are given by: where yi is the activity coefficient of component i and x represents the mole fraction of solute or solvent. Other interaction coefficients have since been established in terms of the various partial molar thermodynamic properties of an alloy; the definitions of these are summarized in a recent paper by Lupis and Elliott.2 Mathematical and experimental studies of such coefficients have received much attention recently, providing a very useful theoretical background to an understanding of the nature of solute interactions taking place in dilute solutions. One of the definitions to arise from such work has been the extension of Wagner's treatment by Lupis and Elliott4 to include an enthalpy interaction coefficient, defined as. where ?Hi is the relative partial molar enthalpy of component i. ?Hi is related to the relative partial molar enthalpy at infinite dilution, ?Hio, and to the enthalpy interaction coefficients by the expression: Values of ?Hi can often be obtained with a high degree of accuracy by calorimetry, and, if the composition of the alloy is carefully controlled by making calculated solute additions throughout a series of measurements, application of Eq. [2] will enable reliable enthalpy interaction coefficients to be determined. Partial heats of solution must be investigated as a function of solute concentrations down to xi = 0, and, since ? values are obtained from the slope of mi plotted against x, great care must be taken to obtain precise data. The data for binary systems which are presently available often require extrapolation of ?Hi values from compositions as great as xi = 0.05 or even 0.1 to obtain limiting heats of solution. Reliable enthalpy interaction coefficients are thus impossible to obtain from published data for most of the alloy systems already investigated. The aim of the present work was to determine values of Au, Ag, Ag, and Au in the limit xsn -1 for the relatively simple Ag-Au-Sn system and from these results to gain some insight into the possible influence

Jan 1, 1969

By A. C. Losekamp, R. M. Fincel, J. B. Conway

TANTALUM like several other metals exhibits a great affinity for or reactivity with certain gases. Tested in atmospheres which are not completely pure this metal becomes contaminated by certain impurities (notably nitrogen, oxygen, and hydrogen) with a resultant change in various properties. Well-known are the drastic changes in hardness, ductility, and electrical resistivity. Also previously recorded are the distortions of the lattice1,2 accompanying the increased content of oxygen and nitrogen in tantalum. This pronounced affinity for certain gases along with the significant property variations thereby produced makes it necessary to observe additional experimental precautions in making various property determinations with tantalum. Some recent measurements of the linear thermal-expansion characteristics of tantalum have made this point quite emphatically. Failure to observe the greatest precautions in reducing the contaminating influence has led to some extremely distorted results. Not only does such operation lead to different heating and cooling curves during the thermal-expansion measurements, but upon cooling to room temperature the sample is found to have suffered a permanent (actually semipermanent since the specimen can be returned to its original length by a 3-hr degassing treatment in vacuum at 2300°C) elongation. In addition, subsequent heatings will not follow the initial heating curve unless the expansion measurements are based on the actual specimen length at the beginning of the heating cycle. These thermal-expansion measurements were made by positioning the specimen horizontally at the longitudinal midpoint of a 20-in.-long, 4-in.-diam resistively heated tungsten tube furnace. The specimens were in the form of 20-mil sheet formed into a sharp U-shape about 0.3 in. in width and 0.3 in. in depth. Fiducial marks in the form of 0.010-in. holes drilled at either end of the 2.5-in.-long sheet specimens were viewed by a paired filar micrometer telescope system mounted on an Invar bar on the top of the furnace. Tests were made in helium with temperatures measured by a Pt/Pt-lORh thermocouple to 1000°C; above 1000°C temperature was measured by means of an optical pyrometer sighted into a black-body hole drilled into the specimen-holding fixture in the vicinity of the specimen. Previous tests with black-body holes drilled in a 0.25-in.-diam rod specimen had confirmed the temperature uniformity between specimens and specimen-holding fixture in this furnace. A typical thermal-expansion curve for arc-cast tantalum in helium is shown in Fig. 1 for the case where no attempt is made to remove all the impurities from the cover-gas atmosphere. The initial heating curve appears smooth and has a shape characteristic of all metals. However, it is known that the sample begins absorbing impurities at temperatures above 1000°C which are sufficient to distort the lattice and lead to specimen lengths which are somewhat larger than would be obtained in the absence of contamination. During the cooling cycle the expansion curve is seen to be significantly different from the heating curve. This is due to the impurity content causing a semipermanent (i.e., permanent until the impurities are removed by vacuum degassing) deformation which will not allow the speci-

Jan 1, 1965

By Strathmore R. B. Cooke, Marcus Digre

That calcium will activate quartz for flotation with anionic collectors such as soaps has been known for a number of years,12'3 and the method has been applied to the concentration of various iron ores4 5 6 as well as to other materials. Clemmer gives the permissible pH range for the activation of quartz by calcium as between 9.5 and 12.5 with an optimum value of 11.0, and Hertzog7 has determined the calcium abstraction of iron ores and of Ottawa sand, but otherwise little quantitative data are available. The purpose of the present investigation was to determine those conditions under which dilute solutions of calcium chloride will activate quartz for anionic flotation and to determine the amount of calcium ion adsorbed by quartz. Those variables, the influence of which was primary, such as calcium, sodium, and hydrogen ion concentrations, were studied. Other factors which influenced the results are discussed in the description of the experiments. Three different experimental methods were used to determine the activation of the quartz. The first method was to treat a sample of ground, deslimed quartz with solutions of calcium chloride and sodium hydroxide, and to determine the calcium adsorbed by chemical analysis of the solution. Advantages are that a direct value for the amount of calcium adsorbed is obtained, and introduction of a collector which may affect the adsorption is avoided. The difficulty is to determine the extremely small differences in the calcium concentrations before and after the abstraction. The second method was to determine the activation of the quartz by observing the contact angle obtained on pressing an air bubble against the polished surface of a piece of quartz immersed in a solution of calcium chloride, sodium hydroxide, and sodium oleate. This is the well-known "contact angle" method. The third method was to determine those conditions under which an air bubble will pick up quartz particles immersed in a solution of the desired reagents. Disadvantages common to the sec- ond and third methods are that introduction of a collector is necessary to obtain bubble contact with the mineral; very small quantities of contaminant can give erroneous results; and no information is obtainable concerning the amount of calcium adsorbed. Advantages are that tedious analyses, which at best give approximate results, are avoided, and the conditions, especially for the third method, closely simulate those of actual flotation. Although the most consistent results were obtained with the third method, this paper describes the techniques used and the results obtained from each of the three methods. Distilled water and analytical grade reagents were used throughout except where otherwise stated. Between tests all glass articles were cleaned with a chromic-sulphuric acid mixture and sodium hydroxide. Abstraction Method The raw material for the tests was Ottawa sand sized between 14 and 28 mesh. Batches of 500 g of this sand were dry ground for 1 hr in an Abbe porcelain mill with 2700 g of quartz pebbles. The batches were split down to samples weighing approximately 30 g, and the weight of each sample was adjusted to exactly this value.

Jan 1, 1950

• As part of $850,000 granted by the House Appropriations Committee for development of manganese in the U.S., the Bureau of Mines will build a pilot plant at Artillery Peak, Ariz., for development of low grade manganese ores. • The historic Argo tunnel and mill in Idaho Springs, Colo., will reopen shortly for the mining of uranium. The Uranium Co. of America has acquired control of the tunnel and mill and 12 nearby mining properties. J. H. Rodgers and G. C. Ridland will manage the operation. •The opening of a new 4000-ton per day coal mine in Washington Co., Pa., and the reopening of another mine of the same capacity in Fayette Co. has been announced by the H. C. Frick Coke Co. They'll help meet added war demands. •A 7000 bbl per day commercial synthetic liquid fuel plant, making gasoline from natural gas at Brownsville, Texas is being operated by the Carthage Hydro-col Corp., a Texaco subsidiary. The gasoline is produced by the Hydrocol process, chemically similar to the Fischer Tropsch process, but differing mechanically in several ways. To operate the process it has been necessary to build an oxygen plant producing 95 pct pure oxygen in quantities equal to U. S. production of commercial oxygen in 1946. •Over 96 pct of the class of 1950 at Montana School of Mines are now employed,, in industry, and they're scattered from MIT to the island of Cuba., • Cobalt, heretofore almost entirely imported, will soon be produced in Idaho. The Calera Mining Co. is building a 600-ton mill in which a cobalt and copper concentrate will be obtained from Idaho ores. •Plans for mining iron ore on the Conarky Peninsula in French Guinea, (an ECA project) call for equipment purchases as follows: 8 wagon drills, electric shovel for mining, conveyor for the port, 8 trucks, wrecker, 2 tractors, as well as miscellaneous accessories and spare parts. •A low-grade lead-zinc mineralization, located east of any known ore bodies in Utah's East Tintic district, has been located by a 2000-ft wildcat USGS drill hole. * Higher-than-going rates have been authorized by the Munitions Board for its stockpile program, where domestic production of scarce materials is low or uneconomical. Payment in excess of 25 pct over the foreign price is now permitted. •A new self-centering conveyor roll, developed by Carnegie-Illinois Steel, is expected to revolutionize materials handling. It completely eliminates the necessity for sideguides to keep materials on a conveyor. See P. 1028. •Great Britain's socialized coal industry employs twice as many miners, but produces less than half as much coal as America's coal industry. last year, British mines produced 28 million fewer tons of coal than the output of the same ,mines in 1939. Absenteeism amounted to a big 12 pot of working time. • Labor market conditions have tightened on almost a country-wide scale. Only 4 out of 143 major labor market areas have a substantial surplus -- less than half the total for May. Growing scarcities of skilled labor are in evidence.

Jan 10, 1950

In 1846 a bill was pending in Congress to reduce, or eliminate, the tariff on coal; the debate caused the same writer to visit the mines on the north side of the James River and to write a letter about them to the same paper.' Omitting the political arguments, his account follows: "July 13, 1846. "Early in the morning we rose, washed, combed, and ate a first-rate breakfast, and then went to the Tuckahoe, mined by Messrs. Sneed and Dietrock. Coal was first discovered here sixty years ago, and mined by Colonel Thomas Randolph, the proprietor of the land. They were worked by him for his smith-shops. Since which time they have been worked periodically, up to the war of 1812, when they were abandoned; and recommenced in 1837 under the management of Dr. W. T.- Scott. Subsequently a Company was formed called Tuckahoe Coal Mining Company, which purchased the whole track at a cost of $30,000. They commenced the sinking of a shaft and went as far as 412 feet, and then pitched the fat all into the fire by hauling off altogether in despair. In 1843 Major Sneed went to work at it, and succeeded. I may here remark that Major Sneed has been the pioneer in this business on the North side of the River, and has sunk more shafts than any other man who has pursued this vocation in Eastern Virginia. The difficulties and expense in sinking these shafts are sometimes immense. The coal on the outcrop or surface is not always a guide to where it may be found imbedded many hundred feet under earth and rock. "The Tuckahoe Pits are on the Eastern end of the coal field, within twelve hundred yards of the Canal, and about twelve miles from Richmond. They employ fifty hands and raise some three hundred thousand bushels of coal per year. It is highly bituminous and excellent for the manufacture of iron. The Tredegar and Belle Isle Rolling Mills are supplied with it. It must be good and of the right kind', or they would not use it. These pits are the only. ones on this side troubled-with gas-of course ventillation is necessary. There is not as much water in this Pit as I have found generally in many others, although they have extended their operations to a considerable distance under ground. I have observed in examining the coal mines, that, where they are sunk over four or five hundred feet, they are annoyed by gas, and where there is a less depth they are troubled with water. It is evident, therefore, that water, in the region of these coal fields, does not run through the earth to any extent, even five hundred feet deep, and the farther you go below that the greater the increase of gas. "We next visited William Cottrell's Pits, situated one mile and a half north of this. He employs some thirty hands, and raises from 4 to 500 bushels per day. "T. & R. Crouch's Pits are one hundred yards north of Cottrell's. This firm employ from 80 to 90 hands, and raise from 8 to 900 bushels per day. They are now

Jan 1, 1942

By C. S. Smith, K. K. Ikeuye

In an earlier paper1 one of the authors called attention to the significance of the relative free energies of grain boundaries and interphase boundaries in alloys in determining the shape and distribution of micro-constituents. The ratio of the interphase and inter-crystalline boundary energies (that is, —?12, where ?12 is the energy of the interface between a crystal of phase 1 and a crystal of phase 2, and ?11 is the energy of the boundary between two crystals of phase 1) will be denoted by F. It is this ratio that determines, by the simple triangle of forces relation, the dihedral angle, ?, of phase 2 where it adjoins a boundary between two grains of phase 1. On a metallographic sample various angles are actually obtained because of the random orientation of the plane of observation, but the statistically most frequent angle is the true one. These basic principles were discussed in detail in the earlier paper. The experiments described below show the effect of both composition and temperature on ? and T for some alloys containing a liquid phase, and provide data on the rate of approach to the equilibrium angles in both solid and liquid phases. All the alloys were melted in a graphite crucible and cast into ingots 3/4 by 11/8 in. cross-section. Some of the aluminum alloys consisted of two immiscible liquids from which uniform castings could not be obtained. The amount of liquid phase varied locally to a considerable extent and the analyses were meaningless. Nevertheless, the composition of the liquid would not differ from that in an alloy of the intended gross composition, and the synthetic composition of the alloys was therefore used in considering the surface energy results. The ingots were given initial deformation by cold-rolling to 50 pct reduction, annealed, and given a second 50 pct reduction prior to cutting into small samples for heat treatment at the times and temperatures subsequently reported. The resulting micro-samples were carefully prepared metallographically and examined at magnifications of 650, 1280, or 2500. The objectives used were 21X, 0.40 NA (dry); 41X, 0.65 NA (dry); and 80X, 1.40 NA (oil emulsion). The appropriate angles were measured by rotation of the stage of a Bausch and Lomb metallograph to align the appropriate boundaries successively with a cross-hair in a micrometer eyepiece. About 250 angles were measured on each phase. Though the angles were read to 1°, the accuracy is probably not above 3°, because of uncertainty in setting the cross-hair tangent to the sometimes curved boundary. The corners of very small particles, particularly in early stages of adjustment after cold-rolling, were difficult to measure and the results were slightly dependent on the magnification used (compare Fig 1-C and 1-D). With particles of larger size and more nearly equilibrium shape, magnification made no difference (vide Fig 1-F and 1-G). The measured angles were grouped in 10° intervals (5° if ? was less than 20°) and plotted in bar

Jan 1, 1950

• A new curriculum for combined liberal arts-engineering education has been announced by 6 middle western colleges. The plan involves three years of ;study at one of the 5 liberal arts colleges and two years and a summer of 'engineering work at Case; graduates receive both the A.B. and B.S. degrees. * A new kind of mining is being pioneered by a pest Virginia coal operator which enables four men to produce 800 tons of coal a day. The machine that makes this possible is a giant auger, 5 ft in diam and 100 ft long. Together with the carriage in which it is moved about, it weighs 60 tons. A mobile, but separate power plant of 1000 hp drives it. ' * The Sorel smelter, which will reduce Allard Lake titanium ores, will utilize five 6-electrode rectangular electric furnaces. Furnace hearth size will be about 18x50 ft, and the furnace will smelt about 300 tons of ore per day, producing 100 tons of iron and 130 tons of 70 pct Ti02 slag. The furnaces will be fed continuously by gravity from charge bins, and tap at intervals of 4 hr or more. Slag will be transferred to a high speed casting machine, using cast iron molds, then crushed for shipment to pigment producers. The iron will be treated to reduce its sulphur content to 0.03 to 0.05 pct, and then cast into small pigs or ingots for shipment to steel mills. • Flying of North Africa's first airborne mangetometer survey was completed this month, covering approximately 20,000 sq km in north central Tunisia for Gulf Exploration Co.'s program there. Mapping was completed in less than 30 days. •Yore than 9000 employees of 11 electric companies are enrolled in a 6-hr program that successfully informs workers on the principles of the American economic system. The course is given by the Middle West Service Co. which claims that before and after employee opinion polls show that the course instilled a better understanding of free enterprise and consequently a favorable response to it. •According to a report issued by the American Geological Institute there will be 2865 graduates in geology, including advanced degrees from U.S. colleges in 1950. This supply of geologists compares with requirements for 1278 at the professional and subprofessional levels. The report contains a detailed statistical study of the supply and demand situation for geologists in the 1949-50 period. •The dark cloud of over-production in the bituminous coal industry has a silver lining, according to Natural Resources Notes. Closing marginal mines, mostly strip and truck mines, will result in lower average costs and higher quality of the coal still produced. The producers that will then constitute the industry will be properly equipped and adequately financed to carry forward an intensive campaign to holdd and increase the markets for bituminous coal. •A light, compact, highly reliable blasting machine which does not rely for its effectiveness on the operator's skill is being tested by the Army Engineers. Operating under all climatic conditions from -65 to 125F, the 50-cap machine consists of a springwound do generator and is waterproof.

Jan 8, 1950

By D. R. de Fontaine

By computing the values of the resolved shear stress for a great many orientations of the tensile axis on all 12 (111) <110> slip systems, Taylor and Elam&apos; were able to map out a stereogram of slip systems, given here, Fig. 1, in Diehl&apos;s notation (see, for example Hauser and Jackson&apos;). The purpose of the present note is to derive such a stereogram by mathematical reasoning and to give a simple method of defining the system with highest resolved shear stress for any direction of the tensile axis, thereby eliminating tedious computation of the Schmid factor. Let the tensile axis, of direction cosines [xyz], make the angles 0 and relative to the slip plane normal [HKL] and the slip direction [hkl] respectively. Fig. 2 shows a simple cubic cell whose edges define a Cartesian coordinate system. Let A be a unit vector of origin 0 supported by the tensile axis. Its end point [xyz] then lies on a sphere of unit radius, on the positive hemisphere of which the planes z = 0, x = y, y = z limit the so called primitive triangle of a standard [loo] stereographic projection. For any point of this triangle, the following hold: 0«2 «y *sx « 1 [l] Now, for given [xpz], the most highly stressed system will be the one for which the following expression of the Schmid factor has the largest possible value: (HKL) belonging to the form (111) and [hkl] to the form <110>, the denominator on the right hand side of Eq. [2] is equal to 1.fi.a. The unknowns H, ... h, . . . can now be determined by correctly distributing +1 and -1 to H, K, L, and +1, -1,O to h,k, 1 giving the numerator of Eq. [2] its greatest positive value (the angles 0 and cpare chosen acute) subject to the condition: Hh+Kk+Ll = 0 [3] since the slip direction must lie in the slip plane. Condition [3] can be satisfied only by having one of its terms vanish and the other two equal to +1 and -1. Taking the case of the tensile axis lying in the primitive triangle, x2y, z and therefore Hh will be chosen equal to +1 with H = h = +1 in order to retain a maximum of + signs. There remain two alternatives: either 1 = 0 or k = 0. 1) take 2 = 0 Then Kk = -1 and the numerator of [2] becomes: Retaining a maximum of + signs gives L = k = +1 and becomes: 2) take k = 0 Then L1 = -1and, likewise, the numerator of [2] becomes: xz - z2 + xy + yz [5] But the difference [5] - [4] can be written: (y - z)(x+y +z) [6] positive or zero by virtue of [I]. If [6] is positive (y > z), then the largest possible value for the numerator of [2] for any xyz inside the primitive triangle is given by [5], i.e., for: That is to say, the active slip system corresponding to an orientat:~on of the tensile axis inside the primitive triangle is:

Jan 1, 1962