Search Documents

By Marston G. Fleming

CRITICAL pH has been defined by Wark1 as that pH value below which a mineral will float and above which it will not float in solutions containing a given concentration of collector but free from other depressants or activators. - The relationship between mineral, collector concentration, and pH is expressed in the form of a critical pH curve determined by the captive bubble method and is generally regarded as being fundamental to the system involved. The mechanism of alkali depression is currently in dispute, two general theories having received authoritative support. The view expressed in Taggart's chemical theory of flotation2 is that in the presence of a critical concentration of hydroxyl ions, all the metal ions available at the surface of the mineral are present as anions of the form [M (OH)x]-y. The formation of the necessary metal xanthate is thus precluded and, furthermore, any metal xanthate coating previously formed, at a lower pH, will be dissolved. Gaudin3,4 and the Melbourne school under Ware hold that alkali depression is caused by the preferential adsorption of hydroxyl ions by the mineral surfaces. This paper describes an investigation of the mechanism of alkali depression in each of the three systems: cerussite-aqueous carbonate-xanthate, cerussite-xanthate, and galena-xanthate. Alkali Depression of Cerussite by Control of Carbonate Ion Concentration Wark and Cox6 have shown that in the presence of Na2CO3 a higher concentration of xanthate is required to effect bubble contact with a cerussite surface than in carbonate-free solutions. To examine this depression of cerussite by sodium carbonate, a series of captive bubble tests was carried out on cerussite specimens in solutions containing 100 mg per liter of potassium ethyl xanthate and varying concentrations of sodium carbonate. The pH was adjusted by the addition of dilute hydrochloric acid. For purposes of comparison a standard critical pH curve was determined for cerussite with potassium ethyl xanthate in solutions containing no added carbonate. In the latter case pH adjustment was made with sodium hydroxide. The experimental method employed in both series was broadly similar to that described by Wark and Cox;7-9 a number of refinements suggested by Sutherland10 were adopted, and the procedure was further developed and modified to suit the particular requirements of the investigation. The relationship between pH and the concentration of potassium ethyl xanthate necessary to induce bubble contact at cerussite surfaces is shown in Fig. 1. The relationship between pH and the concentra- [ ] tion of sodium carbonate necessary to prevent bubble contact at cerussite surfaces in the presence of 100 mg per liter of potassium ethyl xanthate is shown in Fig. 2. Comparison of the. two curves shows that at a collector concentration of 100 mg

Jan 1, 1952

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6'6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure " of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.l Law of Similarity The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simul- taneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size.6'6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increasing section size (Fig. I). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By H. G. Doll

An earlier paper on the general subject of the SP log has analyzed the limitations of that log, in particular when dealing with thin permeable beds enclosed in thick highly resistive ones. Under such conditions, the SP log does not give a good definition of the permeable beds. Selective SP logging is a new method which gives an accurate determination of the permeable beds; even in highly resistive formations, except when the salinity of the mud is extremely high. It also permits a close approxi. mation of the static SP to be obtained. The method consists generally in controlling the potential of auxiliary electrodes located in the drill holes in the vicinity of the measuring electrode. In this manner. the flow of SP current along the drill hole is modified to counterbalance the effect of highly resistive strata. Several procedure; and arrangements used to record selective SP curves and static SP curves are explained. Field examples illustrating these methods are given and discussed. INTRODUCTION In an earlier paper,' the shape of the SP curves and the amplitude of the SP peaks were analyzed, considering how the circulation of the SP current is influenced by the subsurface media as a function of their geometrical configuration and their resistivities. It was shown, in particular. that the permeable beds situated between highly resistive formations are sometimes indistinctly indicated by the deflections of the SP log. It is the purpose of this paper to dircuss a new method now being developed, namely selective SP logging, whose principal feature is to enable a more accurate determination of the depths of the permeable beds present in highly resistive formations, such as occur in limestone fields. It will be shown also how an addi-tional curve called the static SP log can be derived from the selective SP log, or recorded directly, to facilitate the interpretation. Another purpose of the static SP log is to provide an approach toward the determination of the value of the static SP, where this value is not readily given by the SP log. This application. although less important at the present time than that mentioned above, nevertheless is of interest, inasmuch as, according to laboratory and field experiments conducted by several investigators, the determination of oil saturation of reservoirs from the data of the electric log implies the knowledge of the resistivity of the connate water,2,3 to which the static SP seems to be related.4,5,6,7 PRINCIPLE OF SELECTIVE SP LOGGING The method of selective SP logging of the formations traversed by a bore hole consists in recording two curves under the following conditions: The measuring device comprises one measuring electrode M and two additional electrodes G-G', connected to each other. located above and below

Jan 1, 1950

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By A. G. Roach

This paper deals with a plant built under joint agreement between the Canadian and United States Governments to supply the strategic mineral, corundum, at a time when African production was dwindling and war demands still increasing. The operation began in September 1944, retreating the tailings from a former mill by gravity methods, and is still in production (Sept. 1946). In 1942, when it became apparent that South African production would be insufficient to meet mounting wartime requirements of corundum, a survey was made of Canadian sources of the mineral, at the request of the Foreign Economic Administration of the U. S. Government. The investigation' indicated that the quickest and cheapest supply would be obtained by reworking the tailings deposit at Craig-mont, Ontario. Sampling of the dump by Canadian Government engineers revealed that 125,000 tons of tailings, averaging 2.96 pct corundum, was available for retreat-ment. Ore-dressing tests on representative samples of the deposit were conducted by the writer in the laboratories of the Industrial Minerals Section of the Department of Mines and Resources at Ottawa; and gravity concentration on tables was indicated as the most suitable method of treatment. Decision to proceed with the project was deferred until May 9, construction was begun on May 18, and tune-up operation of the plant begun on Sept. IS, 1944. Corundum—Its Properties and Uses Corundum is an oxide of aluminum having the formula Al2O3. Its outstanding characteristic is its great hardness; 9 in the Mohs scale. In this respect it is second only to the diamond. It usually occurs in barrel-shaped crystals in nepheline syenites and other feldspathic rocks deficient in silica. It has a specific gravity of 3.95 to 4.1 and is insoluble and infusible. In color it ranges from white, through red and green, to black. Ruby and sapphire are gem varieties of corundum. Corundum is supplied to industry as closely graded grain.= The coarser roducts (10 to 24-mesh) are used largely for snagging wheels in the steel-castings industry, while the finer grades (from 70-mesh down to flours) find a wide application in the polishing of lenses and for other uses in the optical trade. All sizes of corundum grain are in close competition with synthetic abrasives such as carborundum and alundum. In some fields of application the artificial product is superior to the natural grain but not in' all. The shape of the particle and its behavior under conditions of actual use determine its sphere of employment. The United States is the largest 'Onsumer of corundum, annual consumption in peacetime approaching 3000 tons; during the war this figure was roughly doubled. During the years 1902 to 1913, the bulk

Jan 1, 1948

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By H. L. James

This paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4"; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas. Introduction The U.S- Geological Survey, in cooperation with the Geological Survey Division of Michigan Department of Conservation, has for the past three years been engaged in a restudy of the Iron River-Crystal Falls iron mining district of upper Michigan. The bedrock in a large part of this area is covered with glacial deposits as much as 500-ft thick, and, inasmuch as some of the rocks have moderate to high magnetic permeability, extensive magnetic mapping has been done to assist in unraveling the complicated structure of the area. Several types of instruments have been used, and the major purpose of this paper is to present comparative data on the field performances of some of these instruments so as to aid others who face similar problems elsewhere to evaluate and choose the instruments best suited for the work. The paper is directed primarily to geologists and engineers rather than to geophysicists, although some familiarity with the instruments is presumed. The geology of the area consists of a complexly folded series of weakly metamorphosed sedimentary rocks, including the iron formation, which rests on older greenstones. Although the iron formation itself is only locally magnetic, some of the beds stratigraphically above the iron formation are rather strongly so. By tracing these hanging wall magnetic anomalies valuable information is obtained from which the structure and distribution of the iron formation can be inferred. Critical anomalies range from 25 to 6000 gammas of vertical intensity. Many anomalies can be traced in part with the common dip needle, but detection of others requires more sensitive instruments.

Jan 1, 1949

By H. K. Livingston

A technique has been developed which makes it possible to determine the spreading pressure of liquids and solids, for simple systems. Data for surface tensions, interfacial tensions, spreading pressures, and contact angles for water, heptane, and silica are tabulated.' These results can be applied to the evaluation of capillary rise and displacement pressure in a petroleum reservoir. Appropriate equations are presented and the application of these equations is discussed. The presence of surface-active components affects both capillary rise and displacement pressure and also seems to influence the rate of fluid flow. The purpose of this paper is to supplement and bring up to date the last article on the subject of the surface chemistry of petroleum reservoirs, that of Garrison in the 1935 Oil and Gas Journa1.1 A discussion of the "adhesion tension" concept used by Garrison has been presented in another publication,2 together with the reasons for the recommendation that the term "adhesion tension" be abandoned. In view of the fact that some of the data used by Garrison have been superseded by more recent work, it seemed advisable to call attention to this fact and present the more important data currently believed to be correct. In the earlier paper, Garrison set up the equations that 'relate solid-oil and solid-water interfacial tensions to each other, and applied data from Bartell and Miller3 to these equations. However the adhesion tension measurements made by Bartell and Miller involved a confusion of symbols, so that they did not actually measure the spreading pressure, ?s — ?sf.2 The spreading pressure is a convenient method of indicating the amount by which the surface energy of a solid surface is lowered on immersion in a liquid or vapor. Since the initial value of the free surface energy is represented by the symbol ?s and the final value is ?sF, the spreading pressure is ?s — ?SF. A technique has now been developed4 that makes possible the determination of ?s — ?sF for simple systems. This method would be very difficult to carry out with a multicomponent system such as exists in the petroleum reservoir. However, already results have been obtained for ?s — ?sF for water and heptane in contact with silica and graphite. These values will be of the same order of magnitude as those in the petroleum reservoir. Accordingly, it is possible for the first time to discuss the surface-energy relations of the petroleum reservoir on a semi-quantitative basis. Preliminary Generalizations A petroleum reservoir may contain the following four phases: gas, hydrocarbon liquid, aqueous liquid, and solid. The three fluid phases are dispersed through the solid reservoir rock. If gravity were the only force acting, it is obvious that the

Jan 1, 1943

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,' see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in Cali- fornia, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War 11. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eight-man crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on." Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1953

By H. L. James

This paper presents the results and analysis of field trials of various magnetic instruments over anomalies ranging from 20 to 5000 gammas of vertical intensity. The following instruments were used: Askania vertical magnetometer, Wolfson vertical magnetometer (model M-I), Hotchkiss Superdips (used both parallel to and normal to the magnetic meridian, with several settings of the "sigma" angle), Lake Superior dip needle, and the dipping circle for measurements of inclination. The change in inclination over the measured anomalies ranged up to 4"; this caused pronounced changes in sensitivity of the Hotchkiss Superdip oriented parallel to the magnetic meridian. The variable sensitivity not only gives apparent displacement of crests of anomalies, particularly at high sensitivities, but also makes the data difficult or impossible to use in preparation of iso-anomaly maps. This weakness in field performance of the Superdip is shown to be eliminated by orienting the instrument normal to the magnetic meridian and measuring vertical intensity only, which in the latitude of upper Michigan is equal to 97 pct of the total intensity. The dip needle is seen to be relatively ineffectual for location of anomalies of less than 400 gammas. Introduction The U.S- Geological Survey, in cooperation with the Geological Survey Division of Michigan Department of Conservation, has for the past three years been engaged in a restudy of the Iron River-Crystal Falls iron mining district of upper Michigan. The bedrock in a large part of this area is covered with glacial deposits as much as 500-ft thick, and, inasmuch as some of the rocks have moderate to high magnetic permeability, extensive magnetic mapping has been done to assist in unraveling the complicated structure of the area. Several types of instruments have been used, and the major purpose of this paper is to present comparative data on the field performances of some of these instruments so as to aid others who face similar problems elsewhere to evaluate and choose the instruments best suited for the work. The paper is directed primarily to geologists and engineers rather than to geophysicists, although some familiarity with the instruments is presumed. The geology of the area consists of a complexly folded series of weakly metamorphosed sedimentary rocks, including the iron formation, which rests on older greenstones. Although the iron formation itself is only locally magnetic, some of the beds stratigraphically above the iron formation are rather strongly so. By tracing these hanging wall magnetic anomalies valuable information is obtained from which the structure and distribution of the iron formation can be inferred. Critical anomalies range from 25 to 6000 gammas of vertical intensity. Many anomalies can be traced in part with the common dip needle, but detection of others requires more sensitive instruments.

Jan 1, 1949

By Tell Ertl

THE Piceance Creek Basin in northwestern Colorado is believed to contain the richest large deposit of oil shale in North America. The major portion, about 1650 sq miles, is bounded by the White River on the north, the Grand Hogback, which runs from Meeker to Rifle, on the east, the Colorado River to the south, and the drainage basin of Salt and Douglas Creeks on the west. The Basin is a plateau 7000 to 9000 ft high, composed of 3000 ft of the Green River series of Eocene age and surrounded by a steep escarpment of 1000 to 3000 ft. From the escarpment the beds dip gently toward the center. Although oil shale is found in all members of the Green River series, the rich thick beds are found chiefly in the Parachute Creek member. This is normally capped by 100 to 200 ft of the Evacuation Creek, the youngest member of the Green River series. Actually the Piceance Creek Basin oil shale is not a shale, nor does it contain oil. It is magnesium marlstone holding solid organic matter capable of being broken down by heat into gases, some of which can be condensed into oil. The marlstone is resilient nonporous rock, difficult to sample by pick or hammer and moil. Many companies and individuals prospected the Colorado oil shale shortly after the first World War,1 see Fig. 1, but because of the discovery of large quantities of petroleum in the late 1920's in California, Oklahoma, and East Texas, interest in oil shale development waned and did not revive until World War II. In 1944 the writer, employed by the Bureau of Mines, prospected the high grade oil shale in numerous places along the southern outcrop of the Piceance Creek Basin. Several channel samples about 100 ft in length were cut, see Fig. 2. An eightman crew needed a week to cut a satisfactory channel 80 ft long in the cliff face. The Phillips Petroleum Co., the Union Oil Co. of California and others also prospected the oil shale outcrop. In 1945 the Bureau of Mines initiated a core drilling program for the purpose of obtaining accurate samples from the Piceance Creek Basin. The U. S. Geological Survey set up a program for the geological study of the Basin that is still going on.2 Until the end of 1951 a total of 31 holes was drilled for core with diamond drills, and, in addition, cuttings through the oil shale have been obtained from 4 gas wells drilled by standard rotary oil well rigs. The Bureau of Mines drilled 12 of the holes, the Union Oil Company of California 8, the Standard Oil Company of California 6, the Sun Oil Company 3,

Jan 1, 1952

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By Kenneth C. Vincent, A. M. Gaudin

IN a study1of the action of amyl xanthate on chalcocite in water suspension, it was found that if the xanthate is added in relatively large quantity the xanthate group can be accounted for in three forms: (1) as xanthate ion remaining in water, (2) as benzene-soluble cuprous xanthate on the chalcocite, (3) as a benzene-insoluble coating on the chalcocite. Reduction in the amount of xanthate added leads to disappearance of form 1 then of form 2. With minute quantities of added xanthate, substantially all the reagent is of the "unleachable" kind. Yet this unleachable xanthate can be dissolved by pyridine to form a soluble cuprous xanthate complex, and it is sufficient in effectiveness to make chalcocite flotable even if insufficient in quantity to form a complete monomolecular film on the mineral. In that study it was also found that chalcocite abstracts cuprous xanthate from benzene solution, in what may (or may not) be a case of molecular adsorption. It seemed desirable, therefore, to study further the "unleachable" xanthate on the chalcocite, and particularly to ascertain whether it is formed as a result of the benzene leach or is actually formed during the conditioning of chalcocite in aqueous xanthate solution. A splendid tool to make such studies has recently been perfected; that is, the use of radioactive spies or tracer atoms. With this tool, it was thought possible to answer the problem stated above, but, unfortunately, this did not prove to be true. Answer to the flotation question was clouded by the existence of rapid and selective diffusion of copper atoms in the solid mineral-a phenomenon that was totally unexpected yet remains interesting and perhaps important. METHOD OF RADIOACTIVE SPIES The method of radioactive spies is discussed in many places. Two convenient references are the article by Evans2 and the book by Pollard and Davidson.3 The method was first developed by Von Hevesy and Paneth in 1913, when only natural radioactive isotopes were available. These isotopes are few in number, and so the method remained limited in scope. Recently the synthesis of over 350 active isotopes of all the known stable chemical elements4 has opened widely expanded possibilities for the method. A fundamental tenet of the method is that a radioactive atom and a nonradioactive atom are exactly alike until disintegration of the radioactive atom. Then, by its sudden death, the spy reveals its location. The relative abundance of spies at various locations makes it possible to ascertain the relative abundance of the corresponding nonradioactive atoms at the same times and locations. A second fundamental tenet of the method of radioactive tracers is that the radioactivity lies in the nucleus of the atom: transfer of radioactivity from one

Jan 1, 1944

By R. F. Stilwell

There are three things that all coal consumers look for when they burn coal: (1) suitability for their particular requirements and burning equipment, (2) uniformity of shipments, and (3) quality as expressed by heating value and other chemical and physical tests. Suitability, or proper application, is determined generally from previous buying experience. It is a function of (1) the reliability and integrity of the shipper and distributor, (2) of a certain coal field or seam and of (3) uniformity and quality. Quality is limited by the location and geology of the seam and mine, the mining and preparation methods and equipment and the knowledge and ability of the personnel. Uniformity of shipments is in many ways the most important factor in coal selection. Lack of uniformity in chemical quality, size consist and treatment cause most of the customer complaints that arise from faults of the coal shipper. Lack of uniformity destroys suitability and quality standards, causing a large customer turnover, and greatly increases sales expense and reduces the net return to the operator. Oil and gas fuels are more uniform in quality than solid fuels, and there will be more gas and oil competition for coal markets after this war than before, because the size of their market is a direct function of the dimensions of their pipe lines, which have been greatly increased during the war. Present mechanical coal-cleaning equipment based upon gravity concentration has gone a long way toward giving us a coal of uniform ash content. The chart in Fig. I, by Hebley,1 shows the greater uniformity of the ash content of washed coal as compared with that of raw coal. Wide variation in the nature and amount of ash in the coal feed to the washer leads to a coal of non-uniform ash content. Mechanica1 cleaning equipment does not understand such terms as ash-softening temperature, coking properties, size consist and sulphur content. Unless the feed to the washer is uniform, the washed coal probably will not be uniform. Table I shows the ash, sulphur and ash-softening temperature of two mines in the Pittsburgh bed, both raw and washed, loaded over the same tipple; also No. 3 and No. 4 Pocahontas seams, both raw and washed, loaded from the same preparation plant. It is obvious that they must be blended or loaded separately if a uniform product is to be obtained. Why Is Blending Necessary? It was natural for the operators of captive mines producing by-product coals to recognize the necessity for blending raw coals of different quality and coking characteristics. They have had many years of experience with blending high, low and medium volatile coals at their oven plants. They have found that careful blending gives a coke of more uniform quality and better structure. Coals that could not be

Jan 1, 1947

By George Sachs

I deeply appreciate the honor of being selected to deliver the twentieth Annual Lecture of the Institute of Metals Division. The subject of my paper is extremely involved and voluminous, therefore I shall discuss only some more recent experimental material and speculate somewhat on the physical and mechanical fundamentals of these changes. The flow and the rupture of a solid material are rather different phenomena. It is therefore surprising that up to a rather advanced stage in metallurgical science these two fundamental phenomena have been simultaneously treated and forced into the general conception of the "failure" of solid material. Only in this century, and particularly during the last 20 years, have the very different physical meanings of flow and rupture been clearly recognized. Several hundred of the more recent publications deal with these subjects.1 LAW OF SIMILARITY The basic values commonly considered responsible for the mechanical behavior of any material are the stresses. From this standpoint both a large and a small article made from the same homogeneous metal and of geometrically similar shapes should behave identically, i.e., they should deform geometrically in a similar manner, if subjected to the same stress values at corresponding points. This "law of similarity" was introduced about 60 years ago simultaneously by Barba2 and Kick3 and was derived from the classical theory of elasticity. As far as the plastic behavior of a metal is concerned, this rule appears to be valid. The conventional properties of large and small tension or compression test bars, machined from larger sections, are identical; while the force required to deform a section is proportional to its cross-sectional area and the work consumed in deforming geometrically similar articles in a geometrically similar manner is proportional to its volume. The general trend of the stress-strain diagram of a metal is independent of the section size (Fig. I). No exceptions from this rule are known. However, if the deformation of a metal is continued until rupture occurs, and the breaking stress or the work consumed is measured, a test bar of large cross section appears to fail before or at lower stresses than does one having a small cross section. Thus, the specific impact energy has been often found to decrease with increasing size of the test specimen, particularly for materials with a limited ductility.4 Another exception from the rule of similarity is offered by fatigue-strength values, which usually decrease with increasing section size. 5,6 The conclusion must be drawn from these experimental facts that the ductility of a homogeneous metal decreases with increas¬ing section size (Fig. x). This effect has been actually confirmed by Docherty,7 who observed that in static notch bending tests large specimens failed earlier and in a more brittle fashion than small specimens ma-

Jan 1, 1941

By G. R. Gardner, D. H. Davis

INCREASING realization of the importance of dust control, and the recommendations of various agencies, have led the mining industry to become actively concerned with this problem. The background and necessity for adequate dust-suppression measures have been discussed in a number of publications, including those of the U. S. Bureau of Mines, and the use of spray water to reduce dust at the face and on roadways has been recommended. The problem resolves itself into obtaining adequate dust reduction at a reasonable cost. Inasmuch as the term "adequate dust suppression" has never been clearly defined, nor have permissible limits of dustiness (in terms of dust count) been established, it is apparent that any method selected may be required to meet additional demands. Until the industry has been given some indication of permissible limits of dustiness, no permanent solution is possible. Progress will be somewhat handicapped until such information is available. In addition, dust reduction must be obtained without the addition of any excessive moisture to the coal, since consideration must often be given to: I. Quality standards, particularly reduction in heat value. 2. Handling characteristics, particularly in regard to unloading from railroad cars and bins. 3. Application of dry methods of coal cleaning. 4. Necessity for fine screening within specified limits of oversize and undersize. Little detailed information is available as to the advantages and disadvantages of the several methods of water distribution, the location and protection of sprays, operating data on pressure, quantity of water, and so forth, and results obtained. In 1940 an investigation was undertaken to determine and evaluate the principal factors involved. This paper constitutes a progress report on this work and cannot in any way be regarded as complete on any one of the several phases. CLASSIFICATION OF DUST SOURCES The various sources of underground dust may be classified as primary or secondary. A primary source is one associated with appreciable degradation of size, that is, where the greater part of the actual fines capable of becoming air-borne dust are produced. A secondary source may be considered as one in which the greater part of the fines have been produced at some previous operation and are in such condition that they can be dispersed as air-borne dust. These conceptions appear to be of practical significance, as experience indicates that when dust is controlled at the primary sources the importance of secondary sources is minimized. For these reasons, investigations to date have been concerned principally with the primary sources of dust, and this paper is concerned particularly with one of these-namely, undercutting. In accord with the foregoing definitions, the sources to which the following opera-

Jan 1, 1942

By W. A. Mudge

This discussion will be limited to malleable, commercially pure nickel and some high-nickel alloys, containing more than 50 per cent of nickel, which are produced by The International Nickel Company, Inc. at its Huntington works, West Virginia, from electrolytic nickel or from a nickel-copper sulphide matte. The principal sources of nickel are sulphides of nickel, copper and iron, which are found in the large deposit of pyrrhotite-pentlandite-chalcopyrite ores in the Sudbury area of Ontario, Canada. Pentlandite, a complex nickel-iron sulphide, is the nickel carrier. These ores are concentrated, roasted, and smelted to remove considerable iron and sulphur and to produce a nickel-copper sulphide matte. Separation of the component sulphides of this matte, followed by electrolytic refining, results in the production of electrolytic nickel and electrolytic copper; direct refining of a selected portion of the matte gives the nickel-copper alloy, Monel. FUNDAMENTAL OPERATIONS Melting of the metallic materials is done in natural gas-fired, acid furnaces of the open-hearth, or reverberatory, type, having capacities of 6 to 20 tons; in three-phase, basic, electric-arc furnaces, having capacities of 7 to 20 tons; and in basic, high-frequency induction furnaces having capacities of ½ to 3 tons. Malleable, commercially pure nickel is melted in the acid open-hearth furnace. The charge is sulphur-free, electrolytic nickel, containing 99.9 per cent nickel* and clean mill scrap. Monel, containing approximately two thirds nickel and one third copper, is produced by roasting the nickel-copper sulphide matte to an oxide, smelting the oxide with charcoal in a 20-ton, acid open-hearth furnace, adding clean mill scrap, duplexing to a 20-ton, basic, electric-arc furnace, and refining in this furnace with a lime-fluorspar, carbide slag. Inconel, containing nickel, 80 per cent; chromium, 14 and iron, 6, is melted in the 7-ton electric-arc furnace or the 3-ton induction furnace. The charge is electrolytic nickel, ferrochromium and clean mill scrap. These are the fundamental operations. High-nickel alloys are produced from one of these three materials by additions of suitable amounts of manganese, aluminum, silicon or copper. For example, the age-hardenable alloy, K Monel, is produced from Monel by the addition of approximately 3 per cent of aluminum, and D nickel is produced from nickel by the addition of approximately 4.5 per cent of metallic manganese. For conversion to rods, bars, sheet, strip, tubing and wire forms, by hot-working and cold-working operations, the molten materials are teemed into ingots ranging in size from 14 by 14 by 60 in., 3300 lb., to 36 by 36 by 48 in., 18,000 lb. All ingots are overhauled mechanically before hot working.

Jan 1, 1946

Duval Corporation, the owners of the Sierrita, Esperanza, and Mineral Park copper operations in Arizona, first acquired the mineral rights to their Battle Mountain, Lander County, Nevada, property in 1962. Development of the mine commenced in mid - 1965, and the copper operation began at the end of 1968. The ore, a mixture of chalcocite and chalcopyrite, was milled and floated at a rate of 3, 175 mtpd (3,500 stpd). Because of low copper grade and price, the plant was shut down after about ten years of operation. Attention was then turned to an adjacent low-grade precious metal ore body which contained 2.74 g Au and 3.4 g Ag per mt (0.08 oz Au and 0.10 oz Ag) and minor amounts of copper. Test work revealed recovery by Carbon-In- Pulp treatment would amount to approximately 2.8 mt (90,000 oz) each of gold and silver per year. A rapid engineering and construction schedule resulted in the world's largest, as of late 1980, Carbon-In- Pulp plant being put on-stream in January 1979, with a capacity of 2.720 mtpd (3,000 stpd). Fortunately, the original crushing and grinding plant with all its infra structure was available, and the only modification needed was the addition of a gravity circuit to remove coarse free gold ahead of Carbon- In-Pulp treatment. One of the four primary 500 mm (20 in.) cyclone underflows in the primary ball mill circuit is directed to a secondary ball mill where its product is again cycloned. The cyclone underflow is screened at 3,360 microns (6 mesh) with the undersize being treated on two Pan American 1.07 m by 2. 14 m (42 in. by 84 in.) jigs. Hutch product is further concentrated on two Wilfley tables, a magnetic separator, and on a third Wilfley table where approximately 930 g (30 oz) of gold are recovered each day for amalgamation, retorting, and smelting. Returning to the grinding circuit, the final cyclone overflow is sent to the original plant tailings thickener to obtain proper pulp density for Carbon-In-Pulp treatment. Thickener underflow, at about 40% solids, is then conditioned with air and lime in a series of two 8.5 m by 9.75 m (28 ft by 32 ft) 15O cone bottom Pachucas for oxidation of pyrrhotite. The pulp is then split into two streams for cyanidation for 48 hours in two lines of eight Pachucas of the same size. Pulp is transferred from tank to tank by auxiliary air lifts. Cyanided pulp is then sent to a series of six C. I. P. mechanically agitated tanks with one hour retention in each tank. Originally these

Jan 1, 1981