Search Documents

By E. L. Anderson, J. R. Long, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

By J. R. Long, E. L. Anderson, R. S. Dean, F. S. Wartman

Titanium has been estimated to comprise about 0.65 per cent of the earth's crust and ranks fourth in abundance among the metallic elements suitable for engineering uses. In spite of this, applications of titanium for structural purposes have not as yet been developed. Its commercial exploitation has been largely confined to the chemical industries and the production of paints and pigments; no doubt because of the difficulties that lie in the way of preparing the pure ductile metal. Published reports, however, indicate that ductile titanium can be prepared and possesses some unique properties. This, together with the occurrence in this country of several important titaniferous deposits, has led the Bureau of Mines to investigate processes for the production of metallic titanium, methods required for its fabrication, and the properties that may be produced in this interesting metal. Methods of Preparing Metallic Titanium Many early investigators claimed to have isolated metallic titanium; but in the light of present knowledge, it seems that they really had produced various mixtures of carbides and nitrides that have a metallic appearance but are brittle, hard, and unworkable. The first metallic titanium pure enough to be malleable when cold was produced by Hunter1 in the early part of the twentieth century. Kroll,~ van Arkel,~ and Fast,4 subsequently confirmed the facts that pure titanium is a. ductile metal and that small amounts of impurities were responsible for previous reports of brittleness. When heated, titanium reacts chemically with various gases, such as hydrogen, oxygen and nitrogen; if the volume of gas thus absorbed is too great, the metal becomes brittle and unworkable. The principal difficulty in making ductile titanium is prevention of such contamination, and the success of a given process may be judged by the completeness with which it solves this difficulty in a practical manner. Of the gases mentioned, hydrogen is the least objectionable, since its absorption by the metal is completely reversible and, although dimensional changes occur and absorption of hydrogen embrittles the metal, the gas may be removed readily by heating in a high vacuum for a short time. On the other hand, the absorption of oxygen or nitrogen results in the formation of permanent solid solutions of the oxide and nitride, which cannot be decomposed by the strongest reducing agentsz with sufticient completeness to restore the inherent ductility of the metal. Because of

Jan 1, 1946

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

By K. R. Garr, D. Kramer, A. G. Pard

EXPOSURE of steels to a fast-neutron flux results in helium generation by (n,a) reactions. The elements Fe, Ni, Cr, and N are major participants in the (n,a) reaction and helium concentrations of up to 5 x 10"5 atom fraction could accrue in fuel clads after a year of service in proposed fast reactors.' Such concentrations of helium can severely reduce the ductility of alloys at temperatures of reactor service. The phenomenon of helium embrittlement has been studied in austenitic alloys which were irradiated with particles as a rapid means of producing significant helium concentrations.2-5 The pres-ent work is a continuation of those studies and is concerned with helium effects in a ferritic stainless steel. I) EXPERIMENT Small sheet tensile samples with a gage length of 0.50 in. and a cross-section of 0.009 by 0.040 in. in the gage length were punched from cold-rolled type 405 stainless steel. The composition of the steel used in this work is given in Table I. Prior to helium injection, the samples were annealed 24 hr at 760°C which caused complete recrys-tallization with a resulting grain size of 40 u. This treatment rendered the alloy completely ferritic and carbide particles, 0.5 to 2 uin size, were present at a density of 1 x 1011 cm-3, Fig. 1. These carbide particles were probably a mixture of the M7C3 and M4C types.6 Helium was injected into the samples by irradiation with a particles from a cyclotron, which produced uniform concentrations through the center two-thirds of the sample thickness. Details of this procedure were previously described.' The average helium concentration, as measured on a gas-source mass spec- 11) RESULTS A) Tensile Tests. The results of the tensile tests are given in Table I1 where the values shown are averages of two samples. There was no significant effect of helium on either the yield strength or tensile strength at 550" or 650°C but an increase in both is apparent at 750°C. Samples with helium showed a 20 pct loss in total elongation at 650°C which increased to a 55 pct loss at 750°C. The uniform elongation is not affected by helium at 550" or 650°C but shows an increase at 750°C.

Jan 1, 1970

Discussion of the paper of O. P. Hood, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2607 to 2611. R. V. Norris, Wilkes-Barre, Pa.-I have had a little experience with gasoline locomotives and I want to indorse very strongly Mr. Hood's point with regard to the danger of carbon monoxide poisoning. I think .the terrible danger is not fully realized. I was foolish enough some time ago, in investigating a gasoline locomotive, to attempt to walk out of the mine entry behind it, and for several days I felt very seriously the carbon monoxide effects. The use of gasoline locomotives ought to be confined to mine entries where there is a very large amount of air. One of the grave dangers is their great convenience and the temptation to run them into chambers for just a few moments to get a car or two. GEORGE S. RICE, Pittsburgh, Pa.-Apparently one of the great dangers is in the style of the gasoline engine. When my attention was. first directed to the type of gasoline locomotives which I saw in the foreign mines-France, Belgium, and Germany, I was most favorably impressed with them, and they have given no trouble on account of fumes, so far as I could learn. Large numbers of them were being used, but all were of small capacity, and of a kind in which the speed control is by a governor of the hit-or-miss type, the engine running continuously. Their power capacity was very low, if I remember correctly it was not over 4 or 5 h.p., but they were used under favorable conditions where the grades in the mines were slight, since the entries or tunnels bad a slight grade in favor of-the load, making about the same pull for the empties against the grade as for the load with the grade. I understand the hit-or-miss valve arrangement enables a setting that will give more perfect combustion than can be insured with the valve controlled by the operating man, as in the automobile type of valve and engine used in this country. Apparently the European type of locomotive does not have the capacity to permit use under the conditions existing in this country, where most of our entries or tunnels have variable grades and long heavy trips of mine cars are used.

Jan 4, 1915

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By H. M. Morse

Tinsley Oil Field.—Mississippi joined the oil-producing states when on Sept. 13, 1939, the Union Producing Company's G. C. Woodruff well No. 1, sec. 13, T. 10 N., R. 3 W., Yazoo County, was completed after drilling plug at 4540 ft. in the Woodruff sand of the Eutaw formation of Cretaceous, producing 300 bbl. per day of 34.4" gravity oil through a ¼-in. choke, with a gas-oil ratio of 80 to 1 and bottom-hole pressure of 2045 lb. This was the discovery well in the Tinsley oil field. The well was drilled to a total depth of 4567 ft. and no salt water was encountered. The sand underlies the Selma chalk formation. Nine producing oil wells and one dry hole were drilled and completed by the end of 1939. Two producing sands have been found in the Eutaw and a third sand in the top of the Tuscaloosa formation, called the Woodbine sand in Louisiana and Texas. Faulting is an important factor in the Tinsley field. Total oil production has been approximately 250,000 bbl. from the nine flowing wells. Total depth to top of productive zone was 4540 ft.; to bottoms of productive wells, 4580 ft. Net thickness of the producing formation is 20 to 40 ft., and its porosity is 24 per cent. The deepest zone tested was the Tuscaloosa, in which the depth of hole was 6112 feet. Six hundred and forty acres has been proved for oil production. Jackson Gas Field.—The Jackson gas field has shown a steady decline in the number of wells but the pressure has been maintained. This field is a perfect example of a water-driven field and the time of wells going to salt water is predictable. Five wells were drilled in the Jackson field, of which only one produced. Amory Gas Field.—Interest was renewed in the Amory gas field, where a new well was started in the fall of 1939. Geological Formations.—The deepest well drilled in 1939 was the Willmut Gas and Oil Company's Cleve Love S. F. Johnson No. 1, sec. 29, T. 6 N., R. 1 W., Hinds County. This well encountered the Lower Cretaceous, Trinity series from 3770 to 6422 ft.; Lower Mesozoic from 6422 to 6484 ft. The geological correlations and nomenclature of the formations in Mississippi are shown in the accompanying strati-graphic section.

Jan 1, 1940

By J. O. Nomland

Bahrein 'Island.—In 1936 the Bahrein Petroleum Co. continued drilling additional wells to further increase production. In all, 39 flowing wells have now been finished and five others are drilling. A second well has been deepened for prospecting the deeper horizons but has not been successfully completed as a commercial producer. In addition, a well has recently been drilled near the eastern limit of the producing area for edge-water observation. The present system places wells 3000 ft. apart in a rhombic grid, or about one well to 179 acres. The total production for the year was 4,644,635 barrels. It is expected that refinery capacity of 20,000 bbl. per day will have been completed by July, 1937. A new permanent and enlarged camp with office buildings is being built. A new hospital has been constructed and two additional medical men have been added to the staff. Saudi Arabia.—In eastern Saudi Arabia, the California Arabian Standard Oil Co. has continued with the program of prospect drilling started in 1935. After the gas encountered in Dammam well No. 1 had been successfully shut off, it was completed as a small flowing well of 51" gravity oil. Dammam No. 2, which had been started in 1935, tested 3840 bbl. of approximately 50" gravity oil from a depth of 2175 ft. Dammam No. 5, before being deepened for prospecting lower productive horizons, encountered a gas zone producing 30 million feet. Five other wells on the Dammam dome are in various stages of drilling or completion. Most of these have been located principally to outline the productive area and the various producing horizons of the structure. An extensive program of geological work is being continued. In June, 1936, a well was started on the El 'Alat structure about 25 miles northwest of the Dammam development. Although various tar showings have been reported, the well has not yet, at 2518 ft., reached the depth at which it has been thought that productive horizons might be encountered. A prospect well is being drilled by the Kuwait Oil Co. (jointly owned by Gulf and Anglo-Iranian Oil Companies) in the Sheikdom of Kuwait. The well is near Bahra, a few miles north of Kuwait Bay and about 240 miles northwest of El 'Alat. To date no favorable results at depth of about 6000 ft. have been reported.

Jan 1, 1937

By G. Donald Sherman

THE intense chemical weathering of geological materials in the tropical regions has produced soils that are very rich in their content of iron and aluminum oxides. These soils are commonly referred to as laterites. There is considerable confusion as to the definition of a laterite, since there are workers who consider it to be entirely a ferruginous horizon and others who insist that laterite must have a high content of free aluminum oxide. How¬ever, in general the former is the accepted definition. The indurated ferruginous clay was given the name "laterite" by Buchanan,' not because of its bricklike appearance but rather because bricks were cut from it and used as a building material. Many of the temples of India and Siam are built of this material. This term has come to mean to the geologist a material that includes hard masses of concretionary, cellular, pisolitic ironstones. The soil scientists have deviated from the original meaning of the word and their writings show very little respect for Buchanan's definition or an understanding of the ma¬terial described by him. Pendleton," a life-long student of tropical soils, has insisted that the term laterite be restricted to Buchanan's definition; namely, an alluvial horizon, largely of iron oxides, with a slaglike, cellular or pisolitic structure, and of such a degree of hardness that it may be quarried out and used for building construction. More recently DuPreez2 and Sherman" have eliminated from Buchanan's definition the requirement of a hardness for building construction purposes. In doing this they eliminate the lithological implications in favor of a description of a product, soil, which originates and is developed by pedogenic processes. The confusion of the definition of a laterite is made greater by workers who insist that it must contain bauxite of different degrees of purity. Many of the tropical soils are rich in aluminum oxides. It is natural for the workers who have studied these tropical soils to emphasize the importance of the hydrated aluminum oxides. Hollands reported that the alumina in a laterite existed as bauxite. Fermor3 insisted that a laterite must have a high content of aluminum oxide hydrate, and Fox,4 in 1923, made the suggestion that if a laterite contained enough hydrated aluminum oxide to be used as an aluminum

Jan 1, 1952

By Carl L. Shapiro, Jerome and Strauss

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By Jerome and Strauss, Carl L. Shapiro

This is a critical examination of the theory that the amount of carbon necessary to form the iron-carbon (carbide) eutectoid is lowered by the addition of any carbide-forming element. Although this theory has been built up over a long period of years, it appears, in the light of recent published investigations upon the ternary constitutional diagrams of iron with carbon and other alloying elements, to be no longer tenable. A survey of these new results, summarized below, shows that (as is known) some metals lower the carbon content of the iron-carbon (carbide) eutectoid, whereas others raise it, but (as not heretofore clearly set forth) some first move the eutectoid in one direction and then, at higher concentrations, shift it in the opposite direction. Moreover, these differences in behavior exist even among the common alloying metals classed as carbide formers. PART I Influence of Body-centered Cubic Elements The effects of the various body-centered cubic metals (chromium, tungsten, molybdenum, vanadium, columbium and tan. talum) are reviewed individually. Iron-carbon-chromium System.—In the monograph on Alloys of Iron and Chromium, Kinzel and Crafts1 concluded that the carbon content of the eutectoid is lowered by increasing the chromium content. The quantitative influence of chromium on the eutectoid point of iron-carbon alloys was shown by Monypenny2 (Fig. I) and no data have been forthcoming to refute his findings. Iron-carbon-tungsten System.—Gregg,3 in the monograph on Alloys of Iron and Tungsten, accepted the data showing that tungsten decreases the amount of carbon required to form the eutectoid. The influence of tungsten on the eutectoid percentage of carbon as determined by Oberhoffer and Daeves4 is shown in Fig. 2; these results have received general approval. , I ron-carbon-molybdenum System.—In the monograph on Alloys of Iron and Molybdenum, Gregg5 reviewed the work of Guillet,6 Swinden,7 and ReedI8 all showing that molybdenum lowered the carbon content of the eutectoid, whereas Takei9 contradicted this conclusion. Svetchnikoff and Alferova,10 a little later, showed that large additions of molybdenum shift the eutectoid to the right. These last-named investigators found that molybdenum, up to 1.2 per cent, shifts the pearlite point and the point of maximum solubility of cementite in the gamma phase only slightly in the direction of lower carbon content; on the other hand, increasing amounts of molyb-S

Jan 1, 1944

By George D. Dub

INTRODUCTION OWENS LAKE is at present a source of important nonmetallic minerals, sodium carbonate (soda ash, Na2CO3); sodium sesquicarbonate (trona, Na2CO3.NaHCO3.2H20) and borax, (Na2B407.10H2O). Owens Lake is a closed basin in the southern part of Inyo County, California, at the southern end of Owens Valley, east of the Sierra Nevada Mountains and west of the Coso and Inyo Mountains. Broadly considered, it is in the Great Basin area, but at no time was it a part of Lake Lahontan. CLOSED BASINS Closed basins are phenomena of arid or semiarid regions where outflow is considerably less than inflow and where accordingly soluble salts concentrate in residual liquid. When inflowing waters originate in areas where the rocks are predominantly marine sediments, the residual basin liquid is primarily a chloride brine; if the rocks are largely igneous, the residual brine tends to be alkaline containing carbonates, and sometimes borates as well. Since normally, both types of rocks occur in regions contiguous to closed basins, residual liquids do not often fit into the two broad divisions mentioned. No two residual brines are exactly alike, just as no two ore deposits are exactly alike. Even out of the same closed basin, it is possible to get widely different analyses of liquids since underground and surface flows, as well as local evaporation rates and other conditions might have a marked influence on residual-liquid compositions. At Searles Lake, The American Potash and Chemical Corporation is building a plant to process a lower-level brine which is considerably higher in sodium carbonate and borax, and lower in potassium chloride, than that company has processed for many years. F. W. Clarke1 has classified waters of closed basins as follows: I Chloride type; largely sodium chloride (NaCI) and of oceanic type, such as Great Salt Lake. Related is the Dead Sea, a bittern residue of magnesium, potassium and sodium chlorides. 2. Sulphate type; largely sodium sulphate (Na2S04) with considerable sodium chloride such as Sevier Lake, Utah; Laramie Lakes, Wyoming; Dale Lake, California. 3. Carbonate type; high in carbonates and fairly high in sulphates, such as Moses Lake, Eastern Washington; and the Nebraska Potash Lakes. 4. Carbonate-chloride type; lower in carbonates than type 3 and about equally rich in sulphates, such as Pyramid Lake, Nevada. 5. Sulphate-Carbonate type; quite high in sulphates and carbonates, such as Pelican Lake, Oregon. 6. Triple type; considerable quantities of carbonates, sulphates and chlorides

Jan 1, 1947

By A. H. Underwood, M. –Ls. Trépanier

INTRODUCTION The King and Beaver mines of Asbestos Corporation Limited (ACL) were joined in 1957 to form the King-Beaver mine. In 1964, ACL purchased the Johnson's Asbestos Company. The combined underground workings are a part of the King- Beaver mine. Asbestos ore is mined at the rate of 4080 metric tons per day (mtpd) to provide 15% of the company's daily requirement in the Thetford Mines area. Figure 1 shows the location of Thetford Mines. Two shafts service the underground. No. 3 shaft, 457 m deep, is used for personnel and material transportation, downcast ventilation, and ore hoisting. No. 4 shaft, 820 m to the south, is 389 m deep. It is used for material transportation and upcast ventilation. Figure 2 shows the relative locations of the shafts and the underground workings. The ore is mined by block caving. HISTORY The orebody outcropped at surface and was first mined as an open pit. Underground mining commenced when open pit mining became impractical. Shrinkage stoping, used initially, was unsatisfactory in the highly fractured ore. Sublevel stoping improved ore recovery and safety, but did not overcome the adverse effects of the un- stable rock. Observations of the rock failures indicated that block caving would be satisfactory. This was confirmed by careful investigation and testing. A method of block caving similar to that used at the Miami Copper Company was adopted. The first block commenced production in June 1933. BLOCK CAVING General A large block of ore is undercut above pre- pared drawpoints. The ore above the undercut caves by its own weight. Caving progresses up- ward as the caved ore is drawn. A large proportion of the rock breaks up in the caving action so that it will pass through the drawpoints. Oversize blocks are broken by drilling and blasting or mudcapping. Figure 3 shows the progressive stages of block caving. In the central part of the ore zone, the vertical dimension of a block is determined by the 132 metres between production levels. When isolated ore pockets are developed, the vertical dimensions of a block depend on the extension of the ore zone above the undercut. The minimum horizontal dimension of an under- cut determines the cavability of the overlying block. When necessary, caving is assisted by drilling long horizontal holes into the block above the undercut and blasting them. This procedure speeds up or restarts caving. It will not ensure complete caving of blocks having undercuts less than 30 m wide. Orebodies suitable for block caving are highly fractured and wide enough to cave freely without excessive dilution. Undercutting must

Jan 1, 1981

By M. Cohen, W. J. Harris

The recent application of lineal analysislt2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at Ma and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as 'la lowering of Ma, resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (TA) for a sufficient period of time, more austenite may be retained at a given lower Or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th is measured explicitly in terms of the excess austenite (6) that exists in the steel at T,, over and above the amount that is normally present after direct quenching to T,. T, is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (TA) may be above or below M,, and still cause stabilization depending upon the themistry of the austenite. stabilization has been found to occur in the presence of bainite4 and of martensite6,6,7,8 as well as in the absence of either,g The phe-nomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at T~ that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subscquent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6,8 low alloy6s7.8 and high alloy tool steels.10'5 ssa- with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1949

By A. M. Gaudin, F. W. Bowdish

MINERAL dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,7 its magnetic remanence,3 the turbidity of its suspension,8 and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid-both internal and external-the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample .2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. APPARATUS In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. 1 and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1944

By N. Tiner

THE mechanical properties of magnesium-alloy castings are greatly improved by grain refinement, and at present considerable attention is being paid to methods of obtaining fine-grained castings. One method of achieving this end is the use of proper melting and superheating techniques. These have been employed commercially to a great extent, but no comprehensive study of the subject appears to have been published at present. Numerous investigations found in the literature include some reference to superheating techniques, 1-4 and Achenbach, Nipper and Piwowarsky,5 based principally on thermal analysis, ascribe the grain-refining action of superheating to the influence of solid foreign particles or dissolved gases present in the melt upon the course of crystallization. The primary purpose of this paper is to present the principal facts concerning the effect of superheating on grain size of magnesium alloys. Attempts are also made to explain the experimental results in terms of a general hypothesis. The investigations are limited chiefly to common commercial casting alloys. In order to carry on this work, it was necessary to determine the factors influencing grain size and to develop a proper technique for the preparation of samples. The preliminary tests made by the author indicated that the grain size of magnesium alloys resulting from the solidification of a melt is determined by alloy composition, presence of impurities, rate of cooling during solidification, thermal history of the melt and to some extent the structure of the charge used. The rate of cooling is in turn dependent upon the mass of the melt, pouring temperature, and dimensions, properties and temperature of the mold into which the melt is poured. The final grain size of the alloys is still further modified by heat-treatment subsequent to casting. It is not within the scope of the present paper to discuss all of these factors, and it would suffice to note here that when equal amounts of magnesium alloys are prepared from the same alloying materials, melted in graphite crucibles under the same thermal conditions, then cast into graphite molds at a constant temperature, the .resultant solids have the same grain size. By maintaining all other factors constant, it is thus possible to vary thermal conditions of a melt and to examine the grain size of resultant castings. PREPARATION OF SAMPLES AND GRAIN-SIZE TESTING The alloys investigated in this paper were taken from ingots made by Permanente Metals Corporation or prepared by the author with pure carbothermic magnesium and necessary alloying elements. Melting was carried out under a flux in a graphite crucible heated uniformly by an

Jan 1, 1945

By William J. Harris, Morris Cohen

INTRODUCTION THE recent application of lineal analysis1,2 to the austenite-martensite reaction has made possible a quantitative study of the kinetics of this transformation during rapid cooling. Martensite range curves can thus be constructed to portray the onset of the reaction at [M.] and its subsequent progress as a function of temperature down to and below the ambient. It now seems in order to investigate other aspects of the martensite transformation, using this quantitative method of approach. One of the least understood characteristics of the austenite-martensite reaction is that of stabilization which has been defined by Troiano and Greninger3 as "a lowering of [M.], resulting from aging, without change in chemical composition of the parent solid solution." In other words, if the hardening quench is arrested at a predetermined subcritical temperature (Th) for a sufficient period of time, more austenite may be retained at a given lower or reference temperature (Tr) than if the steel had been cooled directly and rapidly to Tr in the first place. For the purposes of the work at hand, the extent of stabilization produced by the isothermal treatment at Th, is measured explicitly in terms of the excess austenite [(S)] that exists in the steel at Tr, over and above the amount that is normally present after direct quenching to Tr. Tr is conveniently taken to be room temperature, but this choice is not essential and is sometimes undesirable. The holding temperature (Th) may be above or below [M], and still cause stabilization depending upon the chemistry of the austenite. Stabilization has been found to occur in the presence of bainite4 and of martensite5,6,7,8 as well as in the absence of either.9 The phenomenon of stabilization is not concerned with (and may even be obscured by) ferrite formation or any other type of phase change occurring at Th that alters the chemistry of the remaining austenite. Such a structural change would obviously influence the martensite transformation during subsequent cooling. Stabilization, however, is more subtle; it appears to manifest itself without detectable variation of the austenite composition, whether in the presence or absence of transformation products. There are relatively few direct references to stabilization in the literature. The stabilizing effect of room temperature aging and tempering on the subzero transformation of retained austenite has been clearly shown in plain carbon,6.8 low alloy 6.7.8 and high alloy tool steels.10,5 Starting with the as-hardened steel, the degree of stabilization increases with tempering time and temperature through

Jan 1, 1948

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By A. M. Gavdin, F. W. Bowdish

Mineral dressing is an industrial art concerned with the treatment and separation of solids suspended in fluids. Knowledge and evaluation of the area of solid-fluid interface is important in all cases except those involving only large pieces of solid. In fact, many problems relating to comminution, to flotation, to thickening and classification, could be dealt with more rationally if the interfacial area were known. A number of methods have been proposed for the measurement of the surface of certain finely divided solids. Among them are methods using rate of dissolution of the solid,? its magnetic remanence,³ the turbidity of its suspension," and the character of the size distribution of the material.9 The first two are limited to one mineralogical species per sample; the third has certain optical limitations, especially for mineral mixtures, and the fourth is based on an extrapolation of uncertain validity. The need of a better and more general method of surface determination has long been felt, therefore. The method of P. H. Emmett,4 based upon the low-temperature adsorption of vapors, appears to fulfill this need. This method consists in determining the amount of nitrogen that is adsorbed by a given sample of solid at the temperature of boiling nitrogen. The more surface there is on the solid—both internal and external—the more nitrogen is abstracted. In actual operation, the method is somewhat less simple than has been stated so far, in that the nitrogen is adsorbed in an incomplete layer, the completeness and thickness of the layer being related to the pressure of the nitrogen in contact with the sample.2 This circumstance makes it necessary to determine the nitrogen adsorption for three or more values of the nitrogen pressure. Apparatus In the Richards Mineral Dressing Laboratories an Emmett apparatus has been built and tested (Figs. I and 2). A mechanical vacuum pump B and a mercury diffusion pump A work in series to give a high vacuum. The sample, placed in bulb D, can be evacuated by this pump train by suitable operation of the stopcocks in the glass tubing that connects the various parts of the apparatus. C is a McLeod gauge, used to ascertain the order of magnitude of the vacuum obtained, and not for accurate pressure measurements. Pressure measurements are made in the mercury manometer F and gas-volume measurements in the gas burette E. Gases are stored in flasks L (nitrogen) and K (helium), arranged so that definite quantities of these gases can be introduced into

Jan 1, 1947

By Carl F. Floe, John Chipman

THE system molten copper-oxygen-sulphur is of interest from both the practical and theoretical standpoints; practically, because oxygen and sulphur play an important role in the commercial production of copper, and theoretically because it offers a chance to study the reaction between an oxide gas, SO2, and a molten metal. Reactions of this type, such as that between CO or CO2 and molten iron, are important in many metallurgical operations. Again, the determination of any gas-metal equilibrium is of theoretical interest and value insofar as it contributes to the general development of the laws for solution of gases in metals. This problem is being given an increasing amount of attention in modern metallurgy. This paper is the first of a series and presents the results of a determination of the solubility of sulphur dioxide in molten copper at temperatures from 1100° to 1500°C., and pressures from about 20 mm. of mercury to somewhat above atmospheric. REVIEW OF PREVIOUS WORK The solubility of gases in most liquids has been found to obey Henry's law, which states that for a fixed temperature the amount of gas dissolved is directly proportional to the pressure. However this law does not hold for liquid metals. Instead, it appears that for many gases, particularly the simple diatomic ones such as 02, N2 and H2, the amount dissolved in liquid metals is directly proportional to the square root of the pressure. This is known as Sieverts' law. It may be recognized as a special case of Henry's law, which applies when the solute gas is dissociated into atoms or when it reacts with the solvent metal to form solute molecules containing single atoms of the gaseous elements, as, for example: [(MG) l 2M +G2 = 2MG K = Ma X Pa, [I]] which, if the solubility is not too high and the concentration of metal therefore nearly constant, can be simplified to: [MG = Kl Pa,[2]] Following the same reasoning, it would be expected that the solubility of SO2 in copper would be proportional to the cube root of the pressure, the reaction being as follows: [6Cu + SO2 = Cu2S + 2Cu20[3] K _ Cu2S X (Cu20)2 (Cu)6(Pso2)[4]] or, neglecting the change in metal concentration and considering that the concentrations of sulphur and oxygen are both proportional to the volume V of gas absorbed: [8 =KI = Pte, or VSO2= K2 '~/PeO, [S]]

Jan 1, 1941