Search Documents

By D. L. Harris, A. M. Gaudin

THE following results, presented here in condensed form,1 were obtained in a preliminary study of the adsorption of n-hexane thiol, hexyl mercaptan, on sphalerite, zincite, willemite, and quartz, from aqueous solution and from a gas. Interest in this subject was aroused by a Belgian report2 of effective use of hexyl mercaptan for flotation collection of oxidized zinc minerals. The relatively low boiling point, 149°C, of the mercaptan3 suggested the desirability of extending the usual measurements of partition of collector between aqueous solution and gas and between gas and mineral. It is believed that this paper presents the first measurements of this type on a flotation system. Attempts were made to carry out the measurements at equilibrium, but as the work progressed it became increasingly doubtful that this desirable condition had been achieved. To control composition and extent of the gas phase, the apparatus was a wholly-enclosed thermally-controlled glass system. Because of these constraints and the desirability of dealing with pure minerals, a scale of operations was chosen in which a few grams of deslimed mineral were used in each test. It was also necessary to choose a particularly sensitive method for mercaptan analysis, and in fact a method that would permit the experimenters to follow the approach to equilibrium. For these reasons mercaptan marked by radiosulphur 35 was used. An analysis was made for the radiosulphur by a modification of the method of Gaudin and Carr.4

Jan 9, 1954

GENERAL Broken Hill lies at latitude 31º58'S longitude 141º27'E on the semi-arid western plains of New South Wales. From discovery in 1883 until the end of 1969 the lead-silver-zinc orebody has yielded 107,570,000 tons of ore for an overall grade of 13.1% Pb, 6.9 oz Ag/ton and 9.4% Zn.* The orebody currently supports the activities of four mines which are, from north to south, North Broken Hill Limited, Broken Hill South Limited, The Zinc Corporation, Limited and New Broken Hill Consolidated Limited. It is estimated that in 1969 these mines produced about 8 ½ % of world lead production and about 6% of world zinc production. In 1905 The Zinc Corporation, Limited was founded to recover zinc from tailings dumps and moved into mining in 1911 on leases purchased from Broken Hill South Limited at the then southern extremity of the "line of lode". New Broken Hill Consolidated Limited was formed in 1936 to explore and mine for deep ore in the leases to the south of The Zinc Corporation which were purchased from Barrier South Limited. The Zinc Corporation, Limited and New Broken Hill Consolidated Limited mines are both managed by Conzinc Riotinto of Australia Limited, which wholly owns The Zinc Corporation, Limited and has a 32% interest in New Broken Hill Consolidated Limited. * Throughout this paper tons referred to are long tons of 2,240 lbs.

Jan 1, 1970

By R. T. Mishler

I WISH to express my keen appreciation of the article on the above subject by Coe and Clevenger.1 It has been doubly interesting to me, for the reason that the experience recorded and the principles evolved practically parallel the results of similar investigations made by myself and others at The Lucky Tiger Mine, El Tigre, Sonora, Mex. An outline of the work at El Tigre may aid in confirming the principles expressed by Coe and Clevenger. El Tigre has the unenviable distinction of possessing a slime with a much lower settling rate than any recorded in the article discussed. Under most favorable conditions the settling rate is about one-third that reported for the Liberty Bell mill, and one-tenth that reported for the Nipissing, Golden Cycle, and Presidio mills. This slow settling characteristic of Tigre ore has necessitated careful investigation of settling phenomena throughout the various evolutions of the plant. PREVIOUS SETTLING INVESTIGATION AT TIGRE During construction work at the mill, the Metallurgical Engineer in charge, D. L. H. Forbes, ran a series of experiments on settling. His tests proved that deep settling tanks were not ordinarily necessary. The use of tanks 2 or 3 ft. in depth was suggested.2 Later experiments demonstrated that the following principles of settling applied to Tigre pulp.3 1. In settling dilute pulp, settling rates are independent of pulp depth. 2. In settling thick pulp, settling rates are approximately proportional to pulp depth.4

Jan 3, 1917

Geological and Natural History Survey of Minnesota, Minneapolis, Minn W. H Emmons, Director A list of publications will be sent upon application Orders for publications should be addressed to The University of Minnesota Press, Minneapolis, Minnesota The Geological Survey of Minnesota has a record of long and useful service Some of the papers published have been outstanding in their field A series of 24 Annual Reports, covering the years 1872 to 1895-98, inclusive, was issued, of which 16 are still available at a price. More important however, are the six volumes of Final Reports, in which is collected the material presented in the earlier Annual Reports. All the strictly geological papers are found in four of the volumes of the Final Reports. vol 1 (1872-1882), principally geology by counties, 2 (1882-1885), same as 1, 4 (1896-1898), same as 1, 5 (1898-1900), Structural and petrographic geology Prices for each volume, leather $3, cloth $2 50, excluding postage, unless other directions accompany the order, volumes of the Final Reports will be sent express collect. A series of Bulletins has been issued, of which a few are out of print. Considering only those available, and of greatest interest, they are: Bulletin 5, Natural gas in Minnesota, by N H Winchell (1889), 50 cents, 6, Iron ores in Minnesota, their geology, discovery, development, qualities and origin, by N H Winchell and H V.

Jan 1, 1933

In recent years, with the advent of new steelmaking procedures, the emphasis has turned away from conventional teeming and has been directed toward continuous casting. This paper points out the fact that there are still new methods being considered to decrease the problems and costs associated with conventional teeming. Although Inland has had no experience with the repair of mold lugs, we do find some problem with damaged ears associated with mechanically capped steel. When pouring bottle tops, any crane movement or leak from the pouring nozzle may result in steel over the top of the mold which, in turn, may result in the shearing of the mold lugs during stripping. Recent back pouring practices increase the chances of this occurring. At Inland's steelmaking shops, we have tried to combat this problem by various methods such as burning the steel from around the top of the mold at the pouring stand with oxy-gas torches. Last year, No. 4 BOF began a conversion from round to elliptically shaped bottle top caps. This change has greatly reduced the chance of splashing due to crane swing by increasing the dimension in the direction on normal swing. The answer to this particular problem is, however, tighter control of pouring performance. We are presently engaged in a process of re-education of personnel and experimentation with different materials and designs of nozzles, heads, and sleeves to help us achieve our goal.

Jan 1, 1972

By Byron W. Cheever

In the Journal of the Iron and Steel Institute for 1881 (vol. ii., page 379), will be found an article upon this subject. The analyses there reported mere of samples taken from an ingot made especially rich in impurities and then cast in a sand-mould in order to give the elements a better chance to redistribute themselves, on account of the steel solidifying more slowly than when cast in an iron mould. Wishing to ascertain how much, if any, segregation takes place when the steel is cast in the ordinary way, I placed the subject in the hands of Mr. W. J. Olcott, a graduate of the Michigan University, who has carefully collected and analyzed samples taken from different parts of ingots and billets. In this undertaking he found himself somewhat embarrassed on account of being distant from steel-works, and therefore unable to supervise the selection of samples. He found, however, a competent and willing aid in the person of E. F. Wood, M.E., chemist of the Pittsburgh Bessemer Steel Company, Limited, who has spared no pains in collecting the desired samples and furnishing drawings and descriptions of the ingots from which the samples were taken. The following are the results obtained: Ingot No. 1. This ingot was about 5 feet long and 13 X 131/4 inches at the point of fracture, which was 2 feet from the bottom. The samples

Jan 1, 1885

By R. S. Busk

A PREVIOUS paper1 has summarized the effect of A all metallic elements on the lattice parameters of magnesium. The present paper deals with the effect of temperature on the lattice parameters and the way in which that effect is modified by alloyed elements. The experimental techniques for sample preparation, exposure to the X-ray beam, measurement of line diameters, and calculation of the parameters were the same as reported in the previous paper. The temperature of the specimen was raised by surrounding the mounted compact with a conical Glas-Col,* the base of which was sealed with Saran film. In this way the temperature of the specimen could be raised to 200 °C, which was the maximum desired in the present study. Control of temperature was effected by maintaining a constant, desired voltage to the resistance coils of the Glas-Col through a Variac. Temperature was measured by an iron constantan thermocouple embedded in the body of the specimerl so that the thermocouple bead was within 1/16 in. of the surface exposed to the X-ray beam. Variation of temperature during an exposure was less than + 1/4 oF. A series of eight alloys, consisting of pure Mg, Mg+Ag, Mg+Al, and Mg+Sn were studied. All percentage values are in atomic percent. The results are given in Table I. The density values given in Table I were calculated from the lattice parameters, using an equation due to Foote and Jette:"

Jan 1, 1953

By A. Boltax

The effect of cold work on the electrical and magnetic properties of solution-treated and aged Cu-Fe alloys was studied. The electrical resistivity of solution-treated and of aged Cu-1.7 wt pct Fe samples increased by up to 25 and 140 pct, respectively, follozcing a 55 pct reduction of area. The principle contributions to the increase of resistivity of the solution-treated and aged samfiles are examined. Measurements of the .saturation induction, coercive force, and stacking fault Probability are also reported. 1 HIS paper is the second in a series which examine the behavior of the electrical and magnetic prop- erties of Cu-Fe alloys. The first paper1 was primarily concerned with the effects of thermal treatment whereas the present paper examines the effects of cold work on solution-treated and aged Cu-Fe alloys. The effects of cold work on the transformation of the coherent fcc iron precipitate to the ferromagnetic form2 and the coercive force and remanence3 have already been described, but the unusually large increases in resistivity (up to 220 pct) which occlir with cold work have not been reported previously. EXPERIMENTAL METHOD The methods used for alloy preparation, heat treatment, and electrical and magnetic measurements are described elsewhere.1 The specimens, initially 4-in. lengths of 0.0625-in. diam wire, were cold worked by swaging in hardened steel dies. Following each reduction, the samples were etched lightly in hydrochloric acid to remove surface con-

Jan 1, 1962

By C. G. Dunn, J. L. Walter

COULOMB' and Coulomb and Lacombe2,3 have recently discussed secondary recrystallization in soft iron (99.5 pct Fe). They found that the appearance of this phenomenon was dependent on both the presence of impurities and the thickness of sheet specimens. They concluded that impurities such as carbon, sulfur, and oxygen in the soft iron stabilized the matrix structure and allowed growth of a few grains of specific orientations. They also found that secondary recrystallization ceased when the final thickness was small and attributed this complete inhibition of growth in thin sheet to the restraining action of thermal grooves. When purer iron (99.99 pct Fe) was used, normal grain growth but not secondary recrystallization was obtained. On the other hand it is known that the necessary stabilization of the matrix structure for secondary recrystallization in high-purity silicon iron probably does not depend on impurities but more likely results from the specimen thickness effect of Beck et al.,4 according to evidence and ideas advanced by Walter and Dunn,5,6 and Detert.7 Furthermore, Mullins8 has indicated that if a gas-metal surface energy difference exists across a grain boundary equal to or greater than about 3 pct of the grain boundary energy, then such a grain boundary should not become stuck. Similarly, Walter and Dunn have estimated that any increase in restraining force due to increased thermal grooving with decrease in

Jan 1, 1962

By James Fisher

THE copper mines of the Keweenaw Peninsula in northern Michigan have long been of interest in connection with deep earth-temperature measurements. The extraordinary low geothermal gradient of 1° F. in 223.7 ft. announced by Agassiz1 as a result of measurements dating from 1886, although later" stated as in error, served to focus attention on this region as one offering, because of the great depth of the mines, unusual opportunity along this line. Lane,3 Van Orstrand4 and others have made valuable contributions to this study. Fresh opportunities afforded by the constant deepening of the mines, improvements in the accuracy and reliability of temperature-measuring instruments together with increasing knowledge of the heat conductivities and specific heats of the rocks, led the Michigan College of Mining and Technology in cooperation with some of the mining companies to renew work on this problem. It is planned eventually to complete a survey which will make use of the favorable opportunities for deep rock-tempera-ture measurements presented in these mines. This survey should include the determination of a depth-temperature gradient in both conglomerate and amygdaloid mines, and also the variations in temperature at the same depth in different geological formations. The first problem has a direct bearing on the question of providing equipment for necessary ventilation with increased depth. The second may show that a relation exists between the natural rock temperature and the mineral content of the formation.

Jan 1, 1932

By Larry Kaufman, Martin Schatz

The effect of pressure on the extension of the ? loop in the FeSi system has been determined by means of metallogvaphic studies and hardness measurements performed on a series of high-purity Fe-Si alloys containing 7.5, 11.0, and 13.9 at. pct Si, respectively. These mensurements, performed at 42 kbar and temperatures up to 1200oC, indicate that the ? loop is expanded to about 10 at. pct Si at 42 kbar as opposed to a maximum extension of 4 at. pct Si at 1 atm. Comparison of the experimental results with thermodynamic predictions of the pressure shifts yields satisfnctory results. DURING the past few years, several studies have been performed in our laboratory1-' in order to determine the effect of high pressure on phase equilibrium in pure iron and iron-base alloys. The purpose of these studies has been to elucidate the effects of high pressure experimentally and to compare the observed results with predicted pressure effects derived on the basis of known thermody-namic and volumetric data at 1 atm. These studies have included work on pure iron2,5,7 as well as Fe-Ni,1,5 Fe-cr,l,5 and Fe-c4-6 alloys. In addition, Tanner and Kulin3 have reported results of pressure studies on two Fe-Si alloys containing 2.0 and 6.25 at. pct Si. At the time of this latter study, no detailed information was available concerning the difference in volume between the a (bcc) and ? (fcc) phases in the Fe-Si system as a function of silicon content. In order to compare their observations with calculated pressure shifts, Tanner and Kulin were forced to assume that silicon had no effect on the difference in volume between a and ? iron. The resulting discrepancy between their calculation of the a/? phase boundary at 42 kbar and the observed results led them to the conclusion that silicon additions probably decrease the difference in volume between a and ? iron. Recently: Cockett and Davis8,9 have reported de- tailed studies of the lattice parameters of a series of Fe-Si alloys at temperatures ranging from 20" to 1150°C. These measurements, performed on alloys in the bcc and fcc range, show that silicon does indeed decrease the difference in volume between a and ? iron. By correcting the calculations of Tanner and Kulin in line with the observed effect of silicon they were able to show improved agreement between computed and observed pressure shifts.' The present measurements were undertaken to provide additional corroboration of this effect, by extending the range of composition, in addition to exploring a situation where large extensions of a ? loop could result in impingement of the ? field with an ordered bcc phase (based on Feo.75Sio.25). I) EXPERIMENTAL PROCEDURES AND RESULTS The alloys investigated were obtained from Dr. F. Kayser of M.I.T. They were prepared at the Ford Scientific Laboratory by vacuum melting electrolytic iron and high-purity silicon. The melts were poured under an argon atmosphere into hot-topped steel molds. Subsequently the ingots were hot-worked down to 1/2-in.-diam rods. Three alloys containing 7.5, 11.0, and 13.9 pct Si were studied. Carbon, regarded as the principal impurity, analyzed at, or below, 0.001 wt pct for all of the alloys. Prior to pressure-temperature treatment, the rod was annealed for 24 hr in vacuum at 1000°C, water-quenched, and subsequently machined into 0.100-in.-diam by 0.100-in.-long specimens. Subsequent to machining, the specimens were again annealed and then examined metallographically. They were found to exhibit a clear coarse-grained ferrite similar to Figs. 10 and 110 of Ref. 1 and Fig. 2 of Ref. 3. Subsequently, specimens of each alloy were equilibrated at 42 kbar at various temperatures in supported piston apparatus.1,3,4,6 Three specimens, one of each alloy, were wrapped in platinum and exposed simultaneously. The pressure-temperature cycle consisted of increasing the pressure from ambient to 42 kbar at 25oC, heating rapidly to the desired temperature, holding for 15 min, and quenching to 100°C, followed by slower cooling to 25°C and pressure release. The temperature was measured with a Pt/Pt-13 pct Rh thermocouple which was not corrected for pressure effects. Subsequently, specimens were examined metallographically and by

Jan 1, 1964

By D. A. Woodford

In a constant-load creep test, if the density of nlobile dislocations is assumed constant for strains exceeding that corvesponding to the minimum creep rate, it is shown that the creep rate may be approximated by the equation where E is the nominal strain, o0. is the initial stress, and a' the stress fov unit dislocation velocity. The constant C contains the mean density of mobile dislocations and n is a measure of the stress sensitivity of dislocation celocity. This equation is shoum to be applicable to published data on an alloy steel and on nickel. The degree of plastic instability and hence the creep ductility is dependent on the calue of n for these materials. When instability becomes gross and local macroscopic necking occurs, the assumptions are no longer valid. On the basis of this equation, and the strain-time relation derived from it, a method of predicting the creep behavior at different stresses is suggested. MOst analyses of creep data have been concerned with time-dependent transient creep or time-independ- ent secondary creep in constant-stress tests. The far more widely used constant-load test has been neglected in terms of a mechanistic approach. In general, since the strains involved are usually small, the same laws for transient creep may be applied to both types of tests. However, there is no steady-state creep in a constant-load test since the stress increases continuously. Any apparent steady state observed on a strain-time plot is either fortuitous or illusory, and is generally revealed as a continuously varying creep rate on a carefully constructed strain rate vs time plot.* Transient creep may be understood in terms of a simple differential equation representing the change in mobile dislocation density with time:' where p is the density of mobile dislocations. The first term on the right is related to first-order kinetics of dislocation multiDlication and the second to second-order kinetics of exhaustion. On the basis of this equation, several authors2-4 have found good agreement with experimental transient creep curves for a number of materials. When k1p = k2p2, a steady-state creep

Jan 1, 1968

By R. G. Davies

Above 500°C, where dislocation climb is rate controlling, it is observed that the activation energy for creep is independent of the apblied stress, although it varies from 62 kcal per mol at 15 pct A1 to 73 kcals per mol at 20 pctA1 due to the change in short-range ovdw with composition. Below 500°C, when the nonconservative motion of jogs upon dislocations is thought to be rate controlling, the activation energy is stress dependent. A sudden increase in the creep rate, for which no explanation is availab2e, occurs at the highest stress at all temperatures. CREEP has been the subject of numerous research publications during the past decade with most of the attention focused upon high temperature steady state creep, i.e., above 0.5 TM, where TM is the absolute melting temperature, as it is the most amenable to theory. Many of the proposed theories involve the climb of dislocations out of their slip plane, which allows them to circumvent obstacles or to annihilate dislocations of opposite sign on other slip planes.' For pure metals it is observed that the activation energy for this creep is equal to the activation energy for self diffusion.' The position is much more complicated in alloys as there are many possible microcreep mehanisms, as well as dislocation climb, which could be rate controlling. There has been little systematic investi- gation of alloys, but Weertman (lead and indium base alloys)3 and Lawley, Coll, and Cahn (Fe-A1 alloys)4 suggest a microcreep process as the controlling factor. A Cottrell-Jaswon atmosphere mechanism is proposed for the lead and indium alloys, and a mechanism involving crystallographic order for the Fe-A1 alloys. Lawley et al. showed that the formation of a super-lattice, either of the FeAl or Fe3A1 type. decreased the rate and increased the activation energy for creep. From the measurements of lattice parameters,= resistivity,' magnetic properties,7'8 internal friction: and dilatometry10 the ordered region is thought to commence at -19 at. pct Al. However, a recent investigation by the author indicates a value

Jan 1, 1963

By W. C. Hagel, H. J. Beattie

Seven austenitic alloys of varions base compositions and minor-alloy additions were solution-treated, aged systematically between 1200oand 1800oF, and examined by X-ray and electron metallography. Intragranular preczpitations of µ, Laves, s, ?', Ni3Ti, and x phases were observed as a function of composition and aging time and temperatwre. Phase solubility limits were detevtnitzed within 100Fo intervals. These inter metallic compounds fall into two distinct general classes, and whichever class predomznates depends on base composition. It has become increasingly evident that multicom-ponent austenitic alloys are well characterized by their precipitation processes. Since certain groups of elements act as one, the relationships among these processes are reasonably simple; complete identification of such processes is usually attainable by a systematic aging study with a combination of techniques centered on microscopy and diffraction. Several nickel- and cobalt-base alloys illustrating cellular precipitation and its interaction with general precipitation were reported previously.1 The group of alloys covered in the present paper demonstrates precipitation-hardening reactions involving two distinct classes of intermetallic compounds where the predominating class appears to depend on base composition. This dependency ties in with a crystal-chemistry regularity first observed some twenty years ago by Laves and Wallbaum but never amplified to our knowledge. Results of electron-microscope and X-ray diffraction studies on systematically aged hot-rolled alloys known commercially as S-816, S-590, Rene-41, Incoloy-901, M-308, and M-647 are reported here. Some of these alloys have previously undergone minor-phase analyses by other investiators. Alloy S-816 was investigated by Rosenbaum, Lane and Grant,3 and Weeton and Signorelli.4 Rosenbaum found only CbC in hot-rolled bars. Lane and Grant found CbC and a small amount of M6C in the cast structure and stated that both carbides form during aging, most of the precipitation being CbC. Weeton and Signorelli found CbC, M23C6 and a weak indication of a phase after a slow step-down cooling cycle from 2250°F. Rosenbaum also investigated hot-rolled samples of S-590 and identified CbC and M6C. Preliminary information on Rene-41, gained partly from the present work, was reported by Morris.5 Long-time precipitation phenomena in Incoloy-901 at 1350°Fwere investigated by Clark and Iwanski.B heir raw data re- semble those of our present heat with 0.1 pct B, while their interpretation of these data resembles our interpretation of data from another heat with only 0.001 pct B; they made no statement as to boron content. No previous minor-phase studies of alloys M-308 or M-647 have been reported. EXPERIMENTAL METHODS Table I gives alloy compositions in both weight and atomic percent. Specimens were solution-treated from 1700º to 2200ºF, aged at logarithmic-time intervals up to 1000 hours between 1200 and 1800 F, and examined in accordance with procedures previously described in detail. ' ' Phase extractions were carried out in electrolytic cells containing 800 ml of either 7 pct HC1 in denatured ethanol or 20 pct H3PO4 in water. After electrolysis for 48 hr at 0.1 to 0.2 amp per sq inch, residues were separated by filtration or centrifuging. X-ray powder patterns of residues were recorded on a diffractometer for accuracy and on film for sensitivity. Lattice parameters were calculated by least-squares analyses of indexed sin 8 values, and relative abundances were estimated from intensities of strongest lines of each phase. These phase abundances denote relative amounts with respect to each other rather than to the alloy. Mechanically polished specimens were etched in a freshly mixed solution of 92 pct HC1, 5 pct H2SO4, and 3 pct HNO3. Parlodion replicas for the electron microscope were chromium-shadowed in high vacuum at a glancing angle of 20deg. All electron micrographs are reproduced here with the shadowing source above. The correspondence betweenelectronmicrostructures and phases identified by X-rays was established by a high redundancy of correlation between relative amounts at different stages of aging and examination above and below critical transformation or solubility temperatures. EXPERIMENTAL RESULTS S-816 and S-590—The phases found in S-816 and S-590 after various aging and solutioning treatments are listed in Table 11. These data and the observed

Jan 1, 1962

By YANG TSANQ WOO

THE method of making coke that has been adopted at the Kaiping and other collieries in northern China resembles, to some extent, the familiar bee-hive oven process of the United States, except that a kiln with permanent sides is used instead of a closed oven, and the products of combustion are drawn off at the bottom, In building coke-kilns in China, two circular holes, 8 ft. 6 in. in diameter at the bottom and 13 ft. in diameter at the top, are excavated in the ground, both being .connected at the bottom by a flue as shown in Fig. 1. The sides and bottom of the kiln are lined with fire-bricks, and covered with a layer of fire-clay, and a rectangular opening, 6 in. by 8 in., connects the bottom of each kiln with the main flue. Around the edge of the hole, and overlapping the lining, is a wall of fire-brick extending .2 ft. 6 in. above the level of the ground. An open space 5 ft. wide is left in this wall, through which the coal is carried into the kiln and the resultant coke removed. This space, of course, is bricked up during the time that the coking operation is being carried on. The wall is pierced with nine flue-openings uniformly placed around the circumference, each intervening space in the wall being strengthened with a brick buttress, as is shown in Figs. 2 and 4. The floor of the kiln, as well as the main flue, is lined with fire-brick. Before charging the coal, it is first placed in shallow bamboo sieves, 2 ft. in diameter, and immersed in a trough 10 ft. long, and 3 ft. wide, fed with pit-water; in which it is washed by hand. Fig. 3 shows the manner in which the washing is done. From 25 tons of good " dust" coal, 22.5 tons of washed coal are obtained. When ready to charge the coal into the kiln a temporary cone-shaped flue of fire-wood and lump coal is first built to a

Nov 1, 1905

By L. T. Lloyd, H. H. Chiswik

The operative deformation elements in a-uranium single crystals under compression at room temperature have been determined as a function of the compression directions. The deformation mechanisms noted may be arranged with respect to their frequency of occurrence and ease of operation in the following order: 1 — (010)-[I001 slip, 2—{130} twinning, 3—{~172} twinning, and 4bunder special conditions of stress application, kinking, cross-slip, {.-176) twinning, and (011) slip. The composition planes of the (172) and (176) systems were found to be irrational. Cross-slip was shown to be associated with the major (010) slip system, coupled with localized interaction of slip on the (001) planes. The mechanism of kinking was found to be similar to that observed in other metals in that it occurred chiefly when the compression direction was, nearly parallel to the principal slip direction [loo] and was associated with a lattice rotation about an axis contained in the slip plane and normal to the slip direction: the [001] in the uranium lattice. The resolved critical shear stress for slip on the (010)-[100] system was found to be 0.34 kg per mm2 In a single test it was shown that under compression in suitable directions twinning on the (130) also occurs at 600°C. DEFORMATION mechanisms of large grained polycrystalline orthorhombic a-uranium have been studied by Cahn.1 A major slip system identified as the (010) with a probable [loo] slip direction and a minor slip system on the (110) planes were reported; the slip direction of the minor system was not determined. The twinning systems that were identified experimentally included the (130) and the irrational (172) composition planes; observations of other traces which were not as frequent and which did not lend themselves to positive experimental identification led Cahn to postulate on the basis of indirect evidence that twinning also occurred on (112) and (121) planes. In addition to the foregoing slip and twinning mechanisms, Cahn also observed kinking and cross-slip in conjunction with the major (010) system; the cooperative cross-slip plane was not identified. The availability of single crystals to the present authors has enabled them to check these results, particularly with reference to the doubtful mechanisms and the preference of operation of any one mechanism in relation to the direction of stress application. The tests were confined to compression only, primarily because of experimental limitations imposed by the size and shape of the available crystals. The tests were performed at room temperature except for one crystal compressed at 600°C. The compression directions were chosen to obtain a representative coverage of one quadrant of the stereo-graphic projection. To test the existence of some of the deformation elements that were reported by Cahn, but were not found in the present study, several additional crystals were compressed in specifically chosen directions considered most ideal for their operation. Experimental Techniques The single crystals were obtained by the grain coarsening technique described by Fisher? They grinding and polishing on rotating laps, with final surface preparation performed in a H3PO4-HNO3 electropolishing bath. A typical crystal readied for compression is shown in Fig. 1; their dimensions were rather small and depended upon the testing direction. Crystals isolated for compression in a direction close to the [010] axis, which lay roughly parallel to the longitudinal axis of the polycrystalline rod, were about 3 to 4 mm long and 5 mm2 in cross-section, while those prepared for compression in other directions were smaller. Most of the crystals were free from twin markings and showed no evidence of Laue asterism. Several crystals, however, contained twin traces prior to compression; these were identified prior to compression so as to clearly distinguish them from those initiated during deformation. The origin of the twin markings prior to deformation may be ascribed to two sources: thermal stresses and specimen handling during isolation and preparation. Two other types of imperfections in the crystals should be mentioned: inclusions, which were probably oxides or carbides. and three of the crystals contained a small number of spherical included grains (<0.01 mm diam), which were remnants of unabsorbed grains from the coarsening treatment. The volume represented by these imperfections was small, and their presence presented no difficulties in the interpretation of the macrodeformation processes during subsequent compression. Two compression fixtures were employed: crystals A, B, C, E, and G were compressed in a hand-operated screw-driven jig whose compression platens were designed to minimize axial rotation;

Jan 1, 1956

By H. S. Gibson

A PROCESS that has come to be known locally as "multistage stabiliza-tion" has been developed in the Haft Kel field of the Anglo-Iranian Oil Co. in southwest Iran, for the recovery of casinghead gasoline. It con-sists in releasing the dissolved gases from the crude by stages, a practice common in many fields, but which, so far as is known, has nowhere been carried to the extent to which it is employed in Iran. It has been in use there for nearly nine years, during which time some 200 million barrels of crude have been handled by the process. This process of gasoline retention consists in preventing the greater part of the casinghead gasoline hydrocarbons (the butanes and pentanes) from ever leaving the crude, instead of allowing them to be vaporized and then recovered from the lighter gases by the usual compression or absorption processes. Its efficiency is fully equal to that obtained by the absorption process; its disadvantage is that it increases the quantities of ethane and propane in the crude sent to the refinery, but with the growing demand for propane this drawback is vanishing. When casinghead gasoline is recovered as a separate liquid in the Iranian fields, it is blended with the crude, as the only outlet is through the refinery, and the crude-oil pipe line offers the cheapest means of transportation. It is under these conditions that the retention of the butanes and pentanes in the crude by multistage stabilization is a most attractive process, possessing as it does the following advantages: (1) extreme simplicity, (2) low first cost, (3) easy installation, (4) practically 100 per cent operating-time efficiency, (5) no operators required, (6) no water or other services required, (7) negligible maintenance, (8) once established, very little routine testing is necessary. The one essential for reasonably efficient multistage stabilization is that the flowing pressures of the wells should be relatively high; i.e., they should not be less than about one-third the saturation pressure of the crude in the reservoir. This is a very general statement, of course, and much depends on the type of crude and its temperature.

Jan 1, 1939

By C. Wert, P. Bunn

Determination of the solid solubility of gases in metals is usually done by one of two methods. The first is an additive method, in which measurement is made at temperature of the maximum amount of gas absorbed by an initially degassed piece of the metal. Gas additions are made until the dissolved gas first comes into equilibrium with a compound. This method is most useful at relatively high temperatures where the amount of gas absorbed is relatively large and where equilibration of the dissolved gas with the gas atmosphere can be achieved in a relatively short time. The second is a precipitation method. A supersaturated solution of the gas in the metal is held at temperature until equilibrium is established between the gas atoms in solution and a compound. The quantity of dissolved gas is then determined by some physical measurement which is sensitive only to the gas in solution. This method is generally useful in low temperatures. This paper describes measurement of solubility of nitrogen in tantalum whereby measurements at low temperatures using internal-friction methods are plotted together with existing measurements at high temperatures. The solubility is thereby known from less than 0.5 at. pet at 350°C to near 13 pet at 2300°C. Several measurements have been reported of the solubility of nitrogen in tantalum. These are collected in Fig. 1. Three single determinations by Ke,1 Andrews,2 and Brauer and zapp3 are plotted along with a series of measurements by Vaughn, Stewart and schwartz4 and Gebhardt, Seghezzi, and Fromm.5 Although not much doubt exists about the solubility being in excess of 10 at. pet above 2000°C, the solubility indicated at low temperatures depends on whose data are selected as being most reliable. The variation is enormous, being at least an order of magnitude at 500°C. Accordingly, a measurement was begun to examine this discrepancy. The method of measurement finally selected was that of internal friction. A solid solution of nitrogen in tantalum was prepared by heating a tantalum wire in a dilute at-

Jan 1, 1964

By G. R. Leverant, M. Gell

The high- and low-cycle fatigue poperties of MAR-M200 directionally -solidified into columnar-grained and single crystal forms were determined at 1400" and 1700°F. These results were compared with the corresponding properties of conventionally -cast MAR-M200. The low-cycle fatigue lives of the columnar-grained and single crystal materials were similar at both temperatures and were one to two orders of magnitude greater than those of conventionally-cast material. The variations in the fatigue lives among the three forms of MAR-M200 were related to the more rapid rate of intergranular muck propagation compared to that of transgranular propagation. In conventionally-cast MAR-M200, cracks were initiated in grain boundaries and crack popagation occurred rapidly along an almost continuous grain boundary path. In the columnar-grained material, crack initiation occurred on short transverse segments of grain boundaries, but crack propagation was transgranular. The fatigue lives of columnar-grained and single crystal materials were approximately the same because most of the life in both materials was spent in trans-granular propagation. For the directionally -solidified materials, the number of cycles to failure, Nf, can be related to the total strain range, , by: heT = K where n and K are 0.16 and 0.044 at 1400&apos;F and 0.29and 0.098 at 1700, respectively. In addition to intergranular crack initiation in the columnar-grained material, initiation also occurred at we-cracked MC carbides and micropores in both directionally-solidified materials. At 1400°F, fatigue life was reduced with increasing MC carbide size, but at 1700 there was no effect of carbide size. THE creep and stress-rupture properties of conventionally-cast nickel-base superalloys can be greatly improved by directional solidification into either single crystal or columnar-grained forms. The improvement in properties results from a reduction in intergranular cavitation and crack growth in the columnar-grained materials and the complete absence of this fracture mode in the single crystals. This paper describes the effect of grain boundaries on the elevated temperature fatigue properties of the nickel-base superalloy MAR-M200. The effect of cycling frequency on cracking arid fatigue life and the role of MC carbides and micropores on crack initiation are also emphasized. The fatigue properties of columnar-grained and single crystal MAR-M200 at room tem- perature,4,5 and the change in the mode of fatigue crack propagation with temperature6 have recently been described. I) EXPERIMENTAL PROCEDURE The material used in this study was the nickel-base superalloy MAR-M200, directionally-solidified into columnar-grained and single crystal forms. The columnar grains were approximately 0.5 mm in diam. The nominal composition of these materials in wt pct was 0.15C, 9Cr, 12.5W, loco, 5A1. 2Ti, lCb, 0.05Zr. 0.015B, bal Ni. They were solutionized for 1 to 4 hr at 2250°F followed by aging at 1600°F for 32 hr. which resulted in 0.2 pct offset yield stresses of 150,000? 144,000, and 95,000 psi at room temperature? 1400°, and 1700°F, respectively. The corresponding elastic moduli parallel to the testing direction were 19.2. 15.0, and 12.5 x 106 psi, respectively. Specimen design, testing procedures and alloy mi-crostructure have been described previously and will only be summarized here. Following the 1600°F aging treatment. MAR-M200 contains an ordered, cuboidal, y&apos; precipitate 0.3 1 on edge, which is coherent with the 1 matrix. The y&apos; precipitate is quite stable; even after testing at 1700°F. the precipitate is only slightly enlarged and its corners somewhat rounded. The alloy also contains a small volume fraction of micropores, and MC carbides. some of which contain preexisting cracks5 formed during casting. These cracks are always parallel to the long dimension of the carbide. Measurement of MC carbide size has been described previously.5 Axial fatigue tests were conducted in air over a wide range of strain amplitudes in both the high - and low-cycle fatigue regions, with specimen lives varying from about 10&apos; to 10&apos; cycles. Low-cycle fatigue (LCF) tests were strain-controlled with strain varied between zero and a maximum tensile value at a frequency of about 2 cpm. High-cycle fatigue (HCF) tests were stress-controlled with the stress varied between 5000 psi and a maximum tensile value less than the yield stress at a frequency of either 10 cps or 0.033 cps (2 cpm). The temperature in the gage section was controlled to 52°F. Specimen axes were within 5 deg of the [001] growth axis of the single crystals and the common [001 ] growth axis of the columnar-grained material. Specimen gage sections were electro polished prior to testing. After the standard heat treatment, three specimens were coated with a typical aluminide coating applied as a slurry. An additional specimen was given the coating heat treatment without actually being coated. In all cases: specimens were reaged at 1600°F for 32 hr after receiving the coating heat treatment at 1975&apos;F for 4 hr.

Jan 1, 1970

By J. Nagy, D. W. Mitchell, E. M. Murphy

In 1957 research was initiated in the U.S. Bureau of Mines experimental coal mine near Pittsburgh, Pa., to study factors affecting foam generation and transport, to evaluate the effectiveness of high-expansion foam for controlling mine fires, and to develop techniques for applying the method under U.S. mining conditions. These investigations showed that high-expansion foam containing at least 0.2 oz of water per cu ft of foam is effective in controlling experimental underground fires burning coal, wood, and oil. Sometimes the fire was completely extinguished, but more often, it was brought under sufficient control to permit either a direct attack on the fire with a stream of water or loading of the hot material into cars. A progress report&apos; prepared in July 1958 summarized the initial achievements of the USBM experiments. Since then other phases of the foam-plug method for attacking fires have been studied in the laboratory and in the mine. Previous studies by British engineers&apos; of the foam-plug method for fighting mine fires indicated that high-expansion foam was effective in controlling experimental timber fires in an underground passageway. Their subsequent workx-1 pertained to the practical aspects of fighting large fires within a mining area with a foam-plug. CONTROLLING EXPERIMENTAL FIRES In the USBM tests foam was formed by spraying a dilute solution of a foaming agent on a metal or cotton net of 1/8 to 1/4-in. mesh. Air passing through the continuously wetted net forms bubbles of 1/2 to 11/2-in. diam and produces a honeycomb of foam that fills the passageway. Under the ventilating-air pressure, this light-weight plug moves forward through the passageways, around sharp corners, and over obstacles. as illustrated in Fig. 1. High-expansion foam was transported to a wood fire, an oil fire, and 13 coal fires. Figs. 3 and 4 show a typical coal fire before and after attack with foam. In 12 of the 15 experiments the fire was brought under control when the water content of foam was 0.2 oz or more per cu ft. A fire was considered controlled when the flames were quenched and observers could cross the area without wearing breathing apparatus or protective clothing. In the other three experiments, conducted when the water content was less than 0.2 oz per cu ft of foam, the flames were retarded but the fire was not controlled. Coal fires have been attacked successfully by foam introduced at points varying from 155 to 1010 ft from the fire. The time of burning in coal beds 10 in. thick ranged from 11/2 to 5 hrs or more. Most of the experimental fire beds were 15 ft in length. However, in one experiment a floor fire 25 ft long and 5 ft wide was constructed $5 upwind from another fire 15 ft in length; in another instance, the fire was 100 ft long and 5 ft wide. Foam was applied to the fires for periods ranging from 7 to 36 min. The time required for foam application depends on the extent of the fire, time of burning, water content of foam, foam velocity, and degree of fire control desired. In addition to the coal fires, foam was transported to a fire covering 45 sq ft, produced by 15 gal of oil burning in metal trays on the floor. The foam extinguished the oil fire in about 1 min. In one other test, the burning of 1100 lb of dry sawmill slabs stacked in open cribs 4 ft high and 16 ft long was brought under control by foam in 2 min. Composition of Gases in Return Air: In several of the experiments samples of the return air from fire zones were collected; composition of the atmosphere before, during, and after foam application was then determined. Because of condensation in the relatively cool sampling tube, the amount of water vapor was not determined. Analyses showed that concentration of carbon dioxide and combustible gases increased as the foam began passing over the fire. This resulted from the decrease in the volume of air when foam generation started and from the formation of gases when water reached the fire.* The quantity of gases generated would not be greater than that from an equivalent amount of water applied directly to the fire. The highest total concentration of combustibles (CO, CH1, and H2 mixture) obtained during the experiment was about 2 pct; this occurred 6 min after foam reached the fire. This atmosphere was nonex-plosive, but calculations show that if the air flow were reduced to about 5 fpm and if the rate of gas liberation from the fire remained constant, the mixture would be explosive. The use of foam on a fire in all probability would affect the normal ventilation of a mine. If the mine is gassy, this factor must be carefully considered before the foam is applied. APPLICATION OF THE FOAM-PLUG TECHNIQUE IN MINES Equipment and procedures for applying the foam-plug methods must be adapted to the prevailing conditions at a particular mine. Some factors to be considered in developing equipment are: size or extent of the mine, dimensions and number of entries, ventilation system, mining methods, haulage facilities, availability of water, amount of methane liberated, and existing fire-control apparatus. • In most experiments the initial air velocity of 200 fpm decreased to 50 to 100 fpm as the foam plug increased In length.

Jan 1, 1961