Search Documents

By M. F. Trice

PYROPHYLLITE is a hydrous aluminum silicate (A12Si4O10(OH)2)1 that occurs in both the foliated and the massive forms. The foliated variety resembles talc in that it has a greasy feel, a pearly luster, perfect basal cleavage, and usually is white, although in some deposits apple green, gray, brown, russet, and nearly black specimens may be found. The massive deposits of pyrophyllite yield pearl gray to light tan aggregates, some of which are so friable that they may be crushed with the hands into a fine gritty powder. Frequently specimens of the massive variety are studded with crystals of radial structure. The mineral has a specific gravity of about 2.7 and a hardness of 1 on Mohs' scale.1 The chemical composition of commercial pyrophyllite reflects the mineralogy of the deposits, which, according to Stuckey,2 contain pyrophyllite and quartz, together with chloritoid, sericite, and a few other minerals of negligible importance. The latter, he says, "are noticed in but small quantities to the extent they might occur as accessory constituents of an igneous rock or as products of regional metamorphism or weathering. . . . Quartz is abundant everywhere except in the very best grades of pyrophyllite." Analyses of specimens from several deposits are listed in Table 1, showing that the silica content varies from 57 to 73 per cent and the alumina from 22 to 33 per cent. Oxides of iron and the alkaline metals are collectively present, with one exception, to an extent of about 1 to 1.5 per cent. SOURCES At present, North Carolina is the only commercial source of pyrophyllite, although the mineral has been found in small quantities in many parts of the world. The North Carolina deposits are in the "Carolina Slate Belt," which traverses the center of the state in a southwesterly direction. This

Jan 1, 1940

The Subcommittee on Manganese, of the A.I.M.E. Committee on Industrial Preparedness, prepared under date of Jan. 24, 1924, for and at the request of the War Department, a confidential report on manganese as an element in the problem of national defense. This report was later released and published, in slightly modified form, as a separate pamphlet. After the lapse of eight years, in view of the vital position of manganese in the problem of industrial preparedness agenist a war emergency, the War Department made a request to have the onclusions of 1924 reviewed and brought up to date. To comply wi' this request the manganese subcommittee was reconvened and ex' tive studies were once more made of the entire subject of mang? . A new report, with specific recommendations, was submitted + War Department in February, 1932. This second report, with 4. L specific conclusions and recomrnendations expressed to the War Department omitted, has now been released and is hereby published. Following a rather brief discussion of uses of manganese and classification of manganese ores, requirements and sources are dealt with at some length. Domestic ferro-grade reserves are estimated on the basis of price and are shown by means of a curve where tons of metallic manganese are plotted cumulatively against prices ranging from 50¢ to $1.00 per unit; thereby indicating at a glance the tonnage which the Committee believes would become commercially available at any particular price per unit. Foreign sources of ore are described and foreign prices which the domestic producer must meet are considered. The question of a war-emergency reserve is then analyzed, requirements are balanced against apparent resources, and the principal conclusion that emerges is that a war reserve or stockpile is still vital to national defense.

Jan 1, 1934

By A. H. Redfield

BITUMENS have been defined by Abraham1 as substances of variable color, hardness, and volatility; composed principally of 'saturated hydrocarbons, substantially free from oxygenated bodies, sometimes associated with mineral matter; the nonmineral constituents being fusible and largely soluble in carbon disulphide. The principal bituminous substances other than petroleums known to commerce are: (1) native asphaltites, such as gilsonite, grahamite, and glance pitch, distinguished by their hardness and relatively high fusing point; (2) native asphaltic pyrobitumens, such as wurtzilite, distinguished by their infusibility and comparative insolubility in carbon disulphide; (3) mineral waxes, such as ozokerite, distinguished by their high content of crystallizable paraffins; (4) native asphalts, containing varying amouqts of mineral matter, distinguished by the comparative absence of crystallizable paraffins; and (5) bituminous residues obtained from the distillation of petroleum. GILSONITE Gilsonite, a black native asphaltite 98 to 99.9 pct pure, characterized by a hardness of 2 (Mohs), a specific gravity of 1.01 to 1.10, and melting point of 230° to 400°F (K and S), is mined commercially only in northeastern Utah. It occurs in parallel, almost vertical veins, from a few inches to 18 ft wide and 8 to 30 miles long, that cut across the Tertiary limestone and shale of the broad Uinta Basin. The bitumen is believed to have been distilled by heat from oily material in the underlying Green River shale. At the Rainbow mine of the American Gilsonite CO.,† the gilsonite, formerly extracted in an opencut by a system of slopes and benches, is now mined by shafts and horizontal drifts. Little timbering is required. The mining methods of the Raven Mining Co., Chicago, and of the American Asphalt Association and the Utah Gilsonite Co., both of

Jan 1, 1949

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By C. F. Quest, T. S. Washburn

The steel industry has a definite need in its tonnage mills for a formula relating expected tensile strength to the analysis of the steel. The McWilliam-Barnes1 and other less comprehensive formulas are used for this purpose, but these formulas were designed for an analysis range that does not include the medium manganese and silicon-bearing steels. This type of steel is being produced to meet the demand for tensile strength slightly higher than that of ordinary structural steel but not high enough to justify expensive alloy steels. The purpose of this paper is to present a somewhat more comprehensive formula based on data accumulated over a number of years by the Inland Steel Co., and to discuss the method followed in obtaining a formula to fit the data. The resultant formula admittedly is still weak in some respects, but for the expanded analysis range appears to be an improvement over the other formulas. It is hoped that with the collection of more data and possible collaboration with other mills studying this problem it will be possible to work out a more nearly perfect formula. Several publications have been issued on this subject. In some, the equation type of relation was evolved while others made a combination of tables and an equation. The latter include work by Campbel12,3 and Webster.4,5 Campbell classified the steels as acid and basic and applied a different formula to each. For basic steels, he used the equation: Teosile etrength = 41500 + 770C + 1000P + yMn [1 y was a variable depending on the carbon and manganese content of the steel and was listed in tables. Webster investigated acid Bessemer steel and developed the equation: Tensile strength = 38000 + 800C + xTP+ yMn [2]

Jan 1, 1940

By Jeff Steinhoff

INTRODUCTION The Henderson mine utilizes a highly mechanized, continuous, panel-caving, mining system to extract ore from a deep, massive, molybdenite deposit. The mine is located 80.5 km (50 miles) west of Denver, Colorado. The mine surface facilities are located 3,170 m (10,400 feet) above sea level in a steep valley on the eastern side of the Continental Divide. Milling facilities are 24 km (15 miles) west on the western side of the divide at an elevation of 2,804 m (9,200 feet) above sea level. The ore- body is located approximately 3,000 feet south of the valley under Red Mountain. Access to the ore for men and materials is through a 915 m (3,000-foot) deep, 8.5 m (28-foot) diameter, vertical, concrete-lined, service shaft. Access from the mill is through a 15.5 km (9.6-mile) rail haulage tunnel. The mine is ventilated through an additional intake shaft and two exhaust shafts. Mine production at this time is 27,255 mtpd (30,000 stpd). The mine ventilation system supplies 1,038 cubic meters per second (2.2 million cfm) through approximately 60 miles of drifting or 2.7 tons of air per ton of ore mined. There are 130 fans in the mine in fixed locations and in vent lines with 6,900 connected horsepower in the mine. MINING METHOD AND LAYOUT The orebody is divided vertically into two major zones. The upper zone is the 8100-level production area. The bottom zone is the 7700- level production area which is in the early development stage. The rail haulage level at 7500 feet is common to both production zones. Each mine production zone consists of five associated sublevels. The cave undercut level is 16.8 m (55 feet) above the production level. Two boundary cutoff levels are located 44.2 m (145 feet) and 62.5 m (205 feet) respectively above the production level. The fresh-air level is positioned 15.2 m (50 feet) below the production level, and the exhaust vent level is 19.8 m (65 feet) below the production level. Horizontally, each production zone is divided into three panels each, 224 m (800 feet) wide. These panels are caved from south to north. As the caving in one panel nears completion, caving in the adjacent panel is initiated. Development for the caving panels is continuous so that the sublevels above the production level and the production level itself have a combination of development drifting and production-related activities. UNDERGROUND VENTILATION NETWORK The ventilation system is zoned in the same manner as the orebody itself. One major split of 600 cubic meters per second (1,270,000 cfm) ventilates the 8100-level production zone; one split of 100 cubic meters per second (210,000 cfm) ventilates the development of the 7700- level production zone; and one split of 165 cubic meters per second (350,000 cfm) ventilates the 7500 rail haulage level. The haulage tunnel requires an additional 188 cubic meters per second (400,000 cfm) of air. Development-drift ventilation is accomplished by hanging 1.0 m (3.5-foot) diameter steel ducting in the drifts with 40-horsepower, 0.96 m (38-inch) diameter fans supplying 9.4 cubic meters per second (20.000 cfm). The normal maximum length for these systems is 300 m (1,000 feet). The 8100-level production-area ventilation system is especially suited to a high level of mucking activity confined in a small area. Approximately 93 per cent of the mine's total production is transferred from the drawpoints to ore passes in 10 production drifts. The active area in each drift is 300 m (1,000 feet). Twelve 5-cubic-yard LHD units with Cat turbo- charged 170-horsepower engines are assigned to the area. Under these conditions, more than one LHD is assigned to a particular production drift. Adequate ventilation is maintained by making an air change every 97 m (320 feet) along the production drifts. Fresh air is brought into the production drifts from the fresh-air level through 1.37 m (4.5-foot) diameter raises. Air travels south along the production drift to the ore pass where it is exhausted down the ore pass to the exhaust level. The ore pass is followed by another intake which is followed by an ore-pass exhaust. At the south end of the production area, a series of exhaust fans maintain a southerly air- flow through the production level.

Jan 1, 1981

By S. Pearson, L. Rotherham

Measurements have been made of the variation of internal friction with temperature for spectroscopically pure silver, and for o series of solid solutions of silver with cadmium, indium, and tin, using a Ke-type torsion pendulum apparatus. Some experiments have also been made to investigate the effect of nonmetallic impurity on grain boundary relaxation in silver. The effect of the alloying elements is to increase the grain boundary viscosity, and to raise the activation energy for grain boundary relaxation from 22,000 cal per mol for pure silver to 43,000 cal per mol for the solid solutions; the same value being obtained, within the limits of experimental error, for all the alloying elements and solute concentrations investigated. Results of the experiments show exactly the same trend as those obtained previously for a similar series of copper solid solutions. They are in agreement with the general theory of grain boundary relaxation developed by Zener and Ke, but do not seem to be in agreement with either of the mechanisms so far put forward to explain grain boundary slip. EXPERIMENTS described in this paper were made as part of an investigation into the effect of alloying elements in substitutional solid solution on grain boundary viscosity, measured by the internal friction method developed by Ke.&apos; The apparatus and experimental procedure have already been described.&apos; Preliminary work was done with spectro-scopically pure silver. Experimental Work Materials Used—All the materials were supplied in the form of % mm diam wire by Messrs. Johnson Matthey and Co. Ltd. The silver and all the alloying elements used were spectroscopically pure. Composition of the alloys is given in Table I. They were all melted and chill cast under the same conditions as the copper alloys. The ingots were rolled to 1/4 in. sq rod with intermediate annealing at 600°C in an atmosphere of cracked ammonia when necessary. These rods were then drawn to wire by standard procedure with intermediate bright anneals at suitable steps in the drawing operations. Specimens from the annealed wires were sectioned longitudinally. mechanically polished, and examined under the microscope. They were then etched and reexamined. Grain sizes were reasonably uniform for all wires, and no traces of a second constituent were observed. The wires were weighed before and after testing so as to measure any loss of the alloying element due to evaporation. The loss was less than the accuracy of measurement—< 0.1 pct of the total weight— for the Ag-In and Ag-Sn alloys, but appreciable loss of weight occurred in the case of the Ag-Cd alloys. The percentage loss is given in Table 11. X-ray diffraction photographs were taken of all thc wires after test to determine whether there was any marked preferred orientation. Results of the examination are given in Table 111. Experiments on Spectroscopically Pure Silver-— Experiments were made on specimens in which the grain diameter was small relative to that of the wire, and on one specimen in which the grains were grown by the usual strain-anneal method to extend across the full diameter of the wire. These large grained specimens will be referred to as single crystal specimens. The wires were annealed for 11/2 hr at 700°C, and experiments were made at two frequencies of vibration, 1.5 and 0.4 vibrations per sec. The variation of internal friction with temperature is shown in Fig. 1. Experiments on a second small grain specimen gave approximately the same results as for the first wire. It will be seen from Fig. 1 that the peak in the curve for the small grained wire, which is presum-

Jan 1, 1957

By H. L. Lovell, L. H. E. Weyher

Cyclones have been used successfully in the mineral industries to solve solid-liquid as well as solid-solid separation problems in the processing of fine particles. Substantial information is available about the operation of cyclones as thickeners, classifiers, and concentrators using a dense medium. However, very little is known about the operation of the cyclone as a fine coal concentrator not using dense medium. This application of the cyclone, namely to wash fine coal in water, requires that classification phenomena be minimized in order to arrive at an effective separation of the high density ash and sulfur-bearing mineral particles from the low density coal particles over a wide particle size range. The authors have investigated the role of feed pressure, orifice diameters, and vortex-finder length in the cyclone washing of fine coal (--1/4 in.) in water. The results of this investigation show that cyclone washing of fine coal in water is an effective unit operation particularly capable of reducing the inorganic pyritic sulfur content. The combination of hydrocyclones with complimentary equipment such as Sieve bends, shaking tables, and flotation units appears to be especially promising and may ultimately yield fine coal processing systems that could approximate the high recovery efficiencies of today&apos;s coarse coal cleaning circuits. In the future, fine coal beneficiation can be expected to receive even greater research emphasis as a result of increasing sulfur restrictions on all major coal markets. In a previous paper, work, conducted at the Pennsylvania State University, on the hydrocyclone washing of fine coal was discussed.&apos; The initial evaluation based on that wo-rk demonstrated the feasibility of hydrocyclones as fine-coal cleaning devices, and in that previous paper selected test data were presented that showed in principle how product yield and assay respond to variations of the major cyclone operating variables. The present paper reports in greater detail on the findings and presents a comprehensive evaluation of the data as follows: (1) Hydrocyclone throughput rates were related to feed pressure and other variables by regression equations. These equations are compared with other capacity-vs.-pressure drop expressions taken from the literature on classification cyclones. (2) The flow ratio was found to be the most important variable for the separation of the solids. Control of this ratio through various cyclone operating parameters is discussed. (3) The data on the product yield as well as the ash and sulfur assays from the tests were evaluated by means of correlation and multiple regression analyses. Because size-classification phenomena cannot be suppressed completely in hydrocyclone washers, product yield and assay data are regressed against cyclone operating variables separately for different size classes. These equations then reveal how the interactions of the cyclone operating variables vary in terms of the separation for different size classes. (4) Density partitions from additional tests were analyzed by supplementing product-size analyses with sink-float analyses of the separated product size classes. The evaluation of these data show how classification phenomena affect separation by density. The results demonstrate in particular the feasibility of the hydrocyclone washer for removing pyritic sulfur from fine coal. In addition to these specific findings, the investigation points up the value, in general, of using hydrocyclone washers in combination with unit operations such as screening, table concentration, and flotation. In order to make optimum use of the hydrocyclone washers and work out the most effective combination of unit operations, it is important to have careful flowsheet analyses corresponding to the given feed and product requirements. Analyses of this kind are now possible by means of computer simulation of flowsheets and other operation research tools. INTRODUCTION Before proceeding with the detailed treatment and evaluation of our results, it will be useful to review the fundamental aspects of cyclone separators and also restate the experimental procedures and data handling employed in these studies. Review of Cyclone Fundamentals: AS shown in Fig. 1, the basic components of cyclones commonly used

Jan 1, 1970

By K. E. Gray, G. M. Myers

In previous publications,5 results of single-blow bit tooth impacts on saturated rocks at various stress states were reported. This paper extends these earlier works to include study of bit impact tests on salt water-saturated Berea and Bandera sandstone samples under conditions of elevated confining and pore pressure. During the tests dynamic filtration and deposition of a mud cake were occurring due to the presence of drilling mud in the borehole and a borebole-to-formation pressure differential. Results indicate that saturation of these sandstones with salt water tends to make them weaker than when saturated with nonreactive fluids. Plastic failure often occurs even when extremely high fluid-loss muds are present in the borehole. The failure mode tends toward plasticity with decreasing fluid loss. Brittle failure of sandstones in mud-filled holes is apparently relatively rare. Depending on the stress level, and the associated failure mode, withdrawal of the bit tooth induces a tensile force that seems rather important relative to the quantity of rock removed by vertical tooth impact. INTRODUCTION A vast majority of the oil wells drilled today involve the use of colloidal muds having a measurable mud filtrate loss. It is known from field experience that reduction of the water loss of a mud generally results in a reduction of the penetration rate. This paper describes an investigation of crater formation at simulated bottom-hole pressure conditions for drilling fluids having different water losses. The literature on single bit tooth impact (cratering) at atmospheric conditions is extensive, but only a limited amount of work has been performed at the stress conditions similar to that found in oil wells. Spherical penetrator cratering tests on rocks at hydrostatic pressure were performed by Payne and Chippenda1e.1 Chisel impact studies on limestone with independently varying overburden and borehole pressure and atmospheric pore pressure were reported by Garner, et al.2 Gnirk and Cheatham3 performed "static" penetrator tests on dry rocks at equal overburden and borehole pressures. Podio and Gray4 studied the effect of pore fluid viscosity at atmospheric pore and borehole pressures and varying overburden pressures. Their results illustrated the importance of fluid saturation of the rock. Yang and Gray5 reported single tooth impact tests on saturated rocks at elevated borehole, pore and confining pressures, but with equal pore and borehole pressures. For the work reported in Refs. 4 and 5, filtration across the hole bottom purposely was avoided. Maurer6 has investigated the effect of independently varying pore and borehole pressures at elevated overburden pressures by using a zero water-loss mud in the borehole. His tests were carried out under conditions that allowed independent control of overburden, pore and borehole pressures, but without control of filtration at the hole bottom. EXPERIMENTAL APPARATUS AND PROCEDURE APPARATUS The single blow chisel impact apparatus used by Garner,2 as modified for this study, is shown in Fig. 1. A cross section of the pressure vessel is shown in Fig. 2. Several pieces of auxiliary equipment were added to the original apparatus in order that the borehole and pore pressure could be applied in a manner analogous to the actual bottom-hole situation. The pore-pressure system included a filtrate volume-measuring transducer and had sufficient surge capacity to allow filtrate to be injected into the sample without significant changes in pore pressure at points remote to the borehole. The borehole-pressure system contained a cross connection to the pore-pressure system so that both systems could be pressured simultaneously. The borehole-pore pressure differential was applied rapidly by the use of a quick and full-opening valve. The operation of this valve triggered two industrial

Jan 1, 1969

By J. Chipman, N. J. Grant, H. L. Bishop

In a recent review1 of the iron-oxide activity of simple open-hearth type slags containing lime, magnesia, silica, and iron oxide, it was established that activity values were lacking in the range of slag composition most interesting to open-hearth operators. That is, laboratory experimental results were not available for simple slag compositions having basicity ratios ranging from about 1.5 to 4.0 and iron-oxide concentrations ranging from about 10 to 30 pct. However, in order to estimate iron-oxide activities for the range of slag compositions of interest to open-hearth operators, activity values were calculated using ionic concepts of slags by following the treatment of Flood and Grjotheim.2 A study of these data indicated that the desired slag compositions were probably not obtained due to the limited solubility of the basic constituents lime and magnesia. Thus, it was decided to make additional heats equilibrating molten carbon-free iron with slags containing MnO, P2O5, and A12O3 in percentages commonly found in open-hearth refining slags, and to examine the liquid slag field over a greater composition range than that of the simple slags studied previously. The ranges of the constituents used in the present study are summarized as follows: Metal Pct 0 0.070-0.201 PctMn 0.005-0.142 Slag Pet CaO 24.45-41.90 Pct MgO 3.23- 9.21 Pct MnO 1.13- 9.62 Pct FeO 20.08-48.7 Pet Fe2o3 2.23-10.14 Pct SiO, 3.51-28.50 Pct P2O5 0.23- 3.65 Pct A12O3 0.43- 3.38 The experimental procedure consisted of equilibrating the slag and metal in an induction furnace provided with a carbon-arc slag heater as described previously by Winkler and chipman.3 The data obtained were used to establish both the iron-oxide activity values and the activity coefficients for FeO and MnO in the open-hearth type slags. RESULTS AND DISCUSSION I) Iron-Oxide Activity of Open-Hearth Type Slags—The iron-oxide activities of various iron-oxide contents of the open-hearth type slags, as calculated from the oxygen content of the metal by the method of Taylor and Chipman, 4 are plotted against the molar ratio of bases to acids in Fig. 1. The data represent slag-metal studies carried out in the temperature range 1530" to 1700°C. For the purpose of this study, the constituents CaO, MgO, and MnO are assumed equal on a molar basis in their effect on the iron-oxide activity; and, PO2,5 is calculated as an equivalent to SiO2 and A12O3 on a molar basis. The total iron content of the slag is calculated to FeO and is represented by the symbol (FeO) The points presented in Fig. 1 represent the results of this investigation for iron-oxide slags containing between 1 and 8 mol pct MnO and less than about 2 mol pct each of A12o3 and PO2,5 The curved lines shown in Fig. 1 represent the results of the summary1 of the iron-oxide activities of simple slags of the system (CaO + MgO) - SiOz - (FeO),. The solid portions of the curved lines represent experimental data, and the broken portions represent iron-oxide activities calculated from ionic concepts of slags. The iron-oxide values of the open-hearth type slags of this study are in good agreement with the values of the simple iron-oxide slag system. Only a slight modification is indicated. The results of this study suggest that the line for 20 mol pct (FeO), should be lowered slightly in the basicity range 1.5 to about 3.

Jan 1, 1959

By G. L. F. Powell, L. M. Hogan

Large degrees of undercooling have been produced in bulk samples, 400 g, of copper and Cu-O alloys by melting in a slag of commercial soda-lime glass. The maximum degrees of undercooling obtained for copper, hypoeutectic and hypereutectic Cu-O alloy samples were 208°, 218°, and 97°C, respectively. No grain refinement as a function of undercooling was observed for the pure copper samples although in Cu-O alloys there was a marked decrease in grain size at degrees of undercooling greater than 150°C. The grain size change is the result of recrystallization during or immediately following the freezing process. THE first report of a large degree of undercooling in a bulk sample of metal was that by Bardenheuer and Bleckmann1 who produced 258°C undercooling in a 150-g sample of iron by melting in a glass slag. Garbeck2 extended this technique to nickel, cobalt, and copper and reported maximum undercoolings of 220°, 230°, and 60°C, respectively, while Fehling and schei13 undercooled a large number of metals as 2 to 20-g samples slagged in glass. Subsequently, one of the authors4 applied the glass slag technique to bulk samples, -500 g, of silver and obtained a maximum undercooling of 250°C. It was concluded that impurities which normally catalyze nucleation at small degrees of undercooling could be removed by oxidation and solution in a glass slag. Large undercooling of bulk samples of iron, nickel, cobalt, and their alloys has also been reported by other authors.8&apos;10&apos;11 Of the five metals mentioned above, copper was the only one which had not been undercooled by at least 200°C in the form of a large bulk sample. Since copper exhibits high liquid solubility for oxygen, as do iron, nickel, cobalt, and silver, it was considered that a much larger degree of undercooling than that observed by Garbeck for copper should be possible. This was obtained by modification of the technique applied previously to silver and the results of undercooling experiments with 400-g samples of copper form part of this paper. The undercooling behavior of Cu-O alloys was also studied, and the influence of a small oxygen content on the grain structure of undercooled copper was observed metallographically. 1) EXPERIMENTAL The copper was obtained as oxygen-free high-conductivity copper, the major impurities of which were Fe 0.01 pct, Zn 0.015 pct, and Si 0.02 pct. Melting was carried out in an open-ended vertical cylindrical fur- nace wound with Kanthal wire. A schematic diagram of the experimental setup is shown in Fig. 1. The undercooling technique previously used for silver4 involved preoxidation of the samples by melting the silver in contact with the atmosphere. The oxygen content was subsequently reduced by freezing the samples under a glass slag, whereby the oxygen was evolved as gas and the continuous glass cover over the surface prevented re-solution of oxygen when the sample was remelted. Since oxygen is not released as gas when a Cu-O alloy is frozen. the technique had to be modified for use with copper. Also, copper is oxidized during fire refining so that an in situ preoxidation treatment of the samples was not considered to be a prerequisite to large undercooling. Experimentation proved that this supposition was correct. Instead, it was found that care was necessary during melting of the copper under glass to minimize oxygen pickup. Samples of copper weighing 400 g were prepared by adding 50-g pieces of copper to a vitreous silica crucible partly filled with soda lime glass at a temperature of approximately 1000°C. Each piece was quickly immersed in the glass slag and held at this temperature until the oxide coating on the surface decomposed. This change was easily observed and coincided with the formation of gas bubbles in the glass

Jan 1, 1969

By A. E. Dwight, A. F. Berndt

Binary and ternary alloys of uranium with transition metals were prepared with U2X stoichiometry. The compounds U2Tc, U2Rh, U2Os, and U2lr were formed by peritectic or peritectoid transformations, and were shown to be isostructural with U2Ru. The lattice constants are presented. Miscibility relationships obtained from the study of ternary alloys are graphically summarized in terms of an area-of-stability plot. The compound U2Re is not isostructural with either U2Ru or U2Mo. A series of compounds with stoichiometry U2X has been prepared in which X is technetium, rhodium, rhenium, osmium, or iridium. The only other U2X compounds, for which X is related to the above transition metals by proximity in the periodic table, are U2Mo and U2Ru. The structure of U2Mo is the tetragonal C11b type (MoSi2 type)1 and U2Ru is monoclinic, with a new structure type.&apos; This investigation was undertaken to determine if any of the above compounds are isostructural with either U2Ru or U2Mo and to find the range of occurrence of these phases. EXPERIMENTAL Alloys were prepared from stoichiometric amounts of electrolytic uranium (99.99 pet pure) and transition metals of 99.5 pet purity (98+ pet pure Tc), by arc melting on a water-cooled copper hearth under an Ar-He atmosphere. Weight losses were negligible. The buttons were homogenized at temperatures between 700o and 800°C (900°C for U2Tc) in evacuated capsules and air-cooled. The X-ray powder specimens were annealed briefly at the temperature of homogenization. Except in the case of the technetium alloy, metallographic examination was used to determine the number of phases present. The radiation hazard involved in handling technetium precluded the use of metallography to examine U2Tc. The temperature and mode of formation of the U2X phases were determined by heating the metallographic specimens to successively higher temperatures, until examination indicated the presence of chilled liquid or a peritectoid transformation. RESULTS The U2X compounds investigated were found to be formed under the following conditions: UzTc unknown U2Ru peritectic 897o ± 3°C U2Rh peritectoid 755o ± 5°C U2Re peritectoid3 below 750°C Uas peritectic4 920°C U2Ir peritectoid 775o ± 5oC Debye-Scherrer patterns for the above U2X phases were made with CuKa radiation (nickel filter). The similarities in the positions and intensities of the strongest lines in the front-reflection region strongly suggested that U2Tc, U2Ru, U2Rh, U2Os, and U21r are isostructural with only minor differences in the unit-cell dimensions. The known lattice constants and intensities of the Debye-Scherrer rings for U2RU2 were used as a guide in order to index the low-angle X-ray reflections of the U2TC, U2Rh, U2Os, and U2Ir powder patterns. Approximate lattice constants for these compounds were thus obtained and were used along with the intensities observed for U2Ru to index the strongest lines in the back-reflection regions. A sin2 2? correction term was included and the lattice constants were refined and standard deviations estimated by least squares. Comparison of observed and calculated values of Q(= 4 sin2?/?2) used in these calculations are given in Table I. In each case when the positions of lines could not be resolved on the films they were not measured. The final lattice constants, with their standard deviations, are given in Table 11, along with the unit-cell volume and X-ray density. The values of the atomic volume5 of the transition ele-

Jan 1, 1965

By A. E. Deruyttere, J. Van der Planken, M. Laurent, Van den Bergen

FahRENHORST and schmid1 observed that zinc single crystals work hardened less rapidly when strained in liquid air (- 185°C)than in a bath at -82°C, whereas at higher temperatures the rate of work hardening decreased with increasing temperature, as would be expected. Cadmium and magnesium showed no such decrease at -185°C. At that time the observed anomaly for zinc at liquid air temperature probably seemed insignificant. However it later was confirmed2 by experiments in liquid nitrogen (-196°C) and in the mixture solid carbon dioxide-acetone (-77"C) and therefore appeared to be real. seeger3 then suggested that the anomaly might be due to the different wetting of the zinc crystals by the cooling media. Recently a new confirmation was obtained,4 however the cooling media again were different: the rate of strain hardening was found to be lower in liquid nitrogen and liquid oxygen than in pentane cooled to various temperatures down to -126°C. Ekperiments will now be reported in which the medium surrounding the specimen at the different temperatures was the same, namely gaseous air. The single crystals were made from "Overcor 99.99" zinc. They were grown in a vertical traveling furnace on seeds of nearly the same orientations. The diameter of the crystals was 5 mm and the length between shoulders 140 mm. The brass shoulders were stuck to the crystals by means of araldite. A thin steel wire was fixed to each shoulder and served to fasten the specimen to a Houns-field tensile testing machine. The crystals with the shoulders and part of the wires were surrounded by two concentric cylindrical containers. The coolant. either liquid air or ground solid carbon dioxide, was poured into the outer container only. During cooling the containers rested on a support which was removed when the straining was started. In order to check the temperature which the crystals would attain inside the inner container, a hollow bar of zinc in which a thermocouple was fitted was first mounted in the apparatus as a substitute for a crystal. It appeared that a constant temperature, respectively - 183° and -72°C, was attained inside the bar, if a soaking time of the order of 1 hr was allowed and if the outer container was constantly kept filled. Accordingly, this procedure was adopted for every tensile test. To take account of the large scatter, fourteen tensile tests were performed with liquid air and seven with solid carbon dioxide. The orientation of the crystals and the results are presented in the table, in which the symbols have the following meaning: 1 : temperature x : initial angle between basal plane and specimen axis : initial angle between slip direction and specimen axis a : shear strain at fracture 0: average rate of strain hardening = —-——- 100 t0 and Te representing respectively the critical shear stress and the shear stress at fracture. Despite the scatter of the a- and 8— values which is of the same order of magnitude as in the work reported by Seeger and Trzuble,4 it is evident that the strain hardening rate is significantly lower at -183°C thanat-72°C. The table also contains the average values calculated from Seeger and Trauble&apos;s results at the corresponding temperatures: z.e., four results at -183oC and two at-70°, -71°C. These authors calculated 9 in a slightly different way, but this is unimportant. The agreement between the a-values shows that both sets of experiments are comparable despite the differences in experimental techniques. The rates of strain hardening also agree and it may therefore be concluded that the anomaly is not

Jan 1, 1962

By W. Hodge, A. F. Haskins, R. M. Evans

Refractory boron compounds are shown to resist corrosion by molten zinc. Coatings were made from ferroboron and manganese boron by several methods: welding, hard facing, and pack diffusion; and techniques of coatings are very important. Mechanical failure of the diffusion coatings can be partially eliminated by applying them to type 416 chromium steels rather than carbon steels. Welded coatings made with a tungsten arc are better than those made by other welding methods. Sintered compacts of mixtures of iron and chromium borides developed strengths of about 30,000 psi. They resisted corrosion of zinc at 600°C and oxidation at higher temperatures. MOLTEN zinc rapidly attacks common metals of construction. The rate of attack is greatly amplified at temperatures over 500°C. However, there are many applications where it is necessary, or at least advantageous, to use metal construction, such as for galvanizing pots and zinc smelter equipment. Condensers and agitator linings used in continuous zinc smelting processes are eroded and corroded by violently agitated molten zinc. Pumps, tubing, and other parts to permit transfer of molten zinc would be desirable in many zinc handling operations. The development of metallic materials which are resistant to molten zinc also might permit its use as a heat-transfer medium in modern high efficiency power plants. In reviewing previous work on zinc-resistant metals, it was evident that most of the available data refer to corrosion at temperatures just above the melting point. Tungsten and high Mo-Fe alloys containing more than 80 pct Mo resist corrosion by molten zinc.&apos;, &apos; Imhoff states that because chromium is not attacked by zinc, chromium plating improves galvanizing pot life." Nitrided cast iron has been used in die-casting machines&apos; where the molten alloy is 96 pct Zn and 4 pct Al. Other metals that have been suggested as of possible value for zinc resistance are columbium, tantalum, and titanium.V he corrosion of steel by zinc has been discussed by many authors,z, "2 None of these materials resisted corrosion by molten zinc at the temperatures used in this investigation, i.e., 600" to 700°C. I. Exploratory and Resistant-Coating Tests To make a study of zinc-resistant metals, exploratory tests were conducted to sort out roughly those materials which seemed most worthy of further development. This preliminary study included both solid metals and surface coatings. Exploratory Corrosion Tests in Molten Zinc—In initiating a study of this problem, numerous samples of metals and alloys were evaluated by dynamic corrosion tests made at 440 °C. Each metal was tested in its most readily available form, which, because of shape and size, was often unsuited for standard corrosion testing. The equipment used for dynamic corrosion testing of all materials, except in a few initial experiments, is shown in Fig. 1. Samples were tied to tungsten rods with tungsten wire, immersed in the zinc, and revolved at 12 rpm about the circumference of a 4 in. diam circle. Speed of travel was about 12.5 fpm. The molten zinc was protected from oxidation by an atmosphere of carbon monoxide, or, at a later period in the program, by a 9:1 mixture of nitrogen and hydrogen. When the effect of both molten metal and atmosphere was desired, the zinc level was lowered. Special high grade zinc was used in all of the corrosion tests. Corrosion losses for materials tested are shown in Tables I and 11. Whenever the materials were available in suitable form, the losses are reported in mils per year. It was recognized that weight losses on irregularly shaped specimens did not show the corrosion rate but the important consideration—poor resistance to corrosion—could be determined readily.

Jan 1, 1956

By J. E. Neal, C. T. Naber, O&apos

Silicon thin films were deposited by electron beam evaporation in an ultrahigh vacuum onto (0001) and (1102) sapphire substrates. Attempts were made to correlate the structural properties of the deposited silicon films with the following: 1) substrate orientation, 2) substrate surface condition, 3) substrate temperature, and 4) deposition rate. The substrate temperatures were varied between 500° and 1000°C and the deposition rates were varied between approximately 50 and 700A per min. The following sapphire surface treatments were investigated: 1) annealing in the ultrahigh vacuum at 1200° C; 2) heating in a hydrogen atmosphere at about 1350°C; and 3) etching with silicon by evaporating silicon onto sapphire substrates heated to 1200° or 1300°C. Twinned silicon films were occasionally formed at substrate temperatures between the 800° and 1000°C on unprocessed mechanically polished substrates; however, the reproducibility and crystallinity of these films were generally poor. Single-crystal and twinned silicon films were formed at substrate temperatures between 700° and 1000°C on substrates which were silicon-etched at 1300°C prior to deposition. Fiber texture films were formed at substrate temperatures between 500° and 700°C. The (111) lattice plane of the silicon single-crystal films was parallel to the (0001) sapphire plane and the (100) silicon plane was parallel to the (1102) sapphire plane. TECHNIQUES are well-established for growing single-crystal silicon thin films on sapphire by chemical methods.&apos;-* Vacuum epitaxial techniques have a number of advantages over chemical epitaxial techniques in the fabrication of thin film microcircuits.5 One of the most significant is that vacuum techniques are compatible with well-established procedures for forming vacuum-deposited thin-film resistors, capacitors, and interconnections. Salatna, Tucker, and young6 recently reported the formation of relatively poor crystalline-quality silicon films on sapphire by electron beam evaporation in a vacuum of about 7 x 10-7 Torr. The purpose of the investigation described here is to determine the relationships between the structural properties of silicon thin films deposited on sapphire substrates by electron beam evaporation in an ultra-high vacuum and the following: 1) substrate orientation; 2) substrate surface condition; 3) substrate temperature; and 4) deposition rate. The substrate temperatures were varied between 500° and 1000° C and the deposition rates were varied between approximately 50 and 700A per min. Two orientations of sapphire were used: (0001) and (1102). The thick-nesses of the films were between 8000 and 16,000A. The morphology and crystallinity of the deposited films and substrate surfaces were investigated by optical microscopy, electron microscopy, and electron diffraction. APPARATUS AND PROCEDURE A cross section of the ultrahigh-vacuum thin-film evaporator is shown in Fig. 1. The bell jar is stainless steel and copper gaskets are utilized at all seals. High vacuum is attained by a 6001iter per sec ion pump and a titanium sublimation pump. Sorption pumps are used to rough the system to a pressure of about 10 µ prior to starting the ion pump. Vacuums in the 10- 10 Torr range were attained after baking the system at about 250°C for 8 hr. Vacuums in the 10-8 to 10-9 Torr range were maintained during silicon evaporation. The silicon charges, which were cut from p-type single-crystal boules which had resistivities between 2000 and 4500 ohm-cm, were placed in the water-cooled copper crucible of a 180 deg bent-beam 5-kw electron beam evaporator. During evaporation, a molten zone was formed in the top center of the silicon charge, and the portion of the silicon charge in contact with the water-cooled crucible remained solid. The substrate heater, which has been described

Jan 1, 1969

By J. Chipman, J. B. Gero, T. B. Winkler

D. C. Hilty—This paper is a useful and timely addition to our store of quantitative data relating to manganese distribution between slag and metal in steel-making processes. For some time, many of us have suspected that the values of Kmn derived by Körber and Oelsen might be too low, and this paper now appears to confirm that suspicion. Application of the new constant to openhearth data should prove interesting. The manganese deoxidation curves of fig. 4 agree fairly well with direct measurements of isothermal solubilities of oxygen in liquid iron containing manganese that have recently been made at the Union Carbide and Carbon Research Labs., Inc. According to the solubility data just mentioned, however, the curves for 1550" and 1600°C lie much closer to each other than the authors have indicated. In other words, the solubility measurements suggest that the logarithm of the oxygen solubility is not a linear function of the reciprocal of the absolute temperature, as the authors have assumed for their calculations. It seems possible that this discrepancy may be due in part to the authors&apos; use of the distribution coefficient, L,,, obtained from Taylor and Chipman&apos;s curve for the solubility of oxygen in iron as shown in fig. 2. Taylor and Chipman gave the equation of this curve as —6320 Log % 0 - ---T + 2.734 Their data, however, can be fitted equally well by a curve having the equation: 13.23 x104 1.18x10" Log % O = 36.350 -13.23x10 Moreover, this curve also fits the authors&apos; oxygen distribution data somewhat better than does the linear curve of Taylor and Chipman. Its use in the derivation of Lo for calculation of the deoxidation curves by the authors&apos; eq 15 causes the effect of temperature on the calculated curves of fig. 4 to agree quite well with the temperature effect that has been observed. An experimental determination of the temperature coefficient of the manganese reaction appears to be desirable. J. E. Stukel—Because the authors have done such an excellent job, my comments will be confined to additional information. Very shortly Professor T. L. Joseph and I will publish the results of a study of the reaction between molten manganese and silica. It was found that electrolytic manganese, melted in silica crucibles, reacted with the silica to form a silico-manganese alloy containing 18 pct silicon (1500°C) and a silica saturated MnO-SiO, slag. Therefore, the presence of silicon and its oxides in the Fe-Mn-0 system will affect the equilibrium. Carbon is also an important factor. The higher the carbon content of the iron the less ability manganese has to reduce silica. As a matter of interest, recently a study of the manganese equilibrium in carbon saturated iron and blast furnace slags was completed at Carnegie Institute of Technology. As a comparison to the present study, 2 to 5 hr were required to reach equilibrium and temperature was a much more important factor than slag composition in determining the (Mn)/(MnO) ratio. These results will also be published in the near future. It can be seen, therefore, that the results of this paper cannot be applied directly to openhearth studies without a degree of flexibility. J. Chipman (authors&apos; reply)—With regard to the effect of silicon on the manganese constant, this effect is, of course, known. Much more data is needed in order to establish it accurately, and I hope we can look forward to having some accurate data on that. Mr. Hilty suggests that a three-term expression for the Taylor-Chipman solubility of oxygen in liquid iron might fit a little better than the two-term equation. I think that it would be too great a compliment to the precision of the data to employ a three-term equation, and I would still recommend the simple, two-term expression.

Jan 1, 1951

By J. V. Richards

(Canal Zone Meeting, November, 1910,) THE Altar district, State of Sonora, Mexico, is for the most part a desert with but little rain-fall and few running streams. On account of this scarcity of water it is necessary for the natives to " dry-wash" the placer-gravel, and the object of the present paper is to describe some of the more common Mexican dry-washing devices. My observations were confined to a property known as Las Palomas placers, 15 miles from the Gulf of California and about 150 miles south of the United States border; a brief description of which property may be of interest as illustrating what is, perhaps, a typical Sonora dry placer. It is said that as long as a century ago the Yaqui Indians discovered rich cement-gravel, known as argo masa, at Las Palomas, and that there has been a more or less steady production of gold from the property ever since. The argo masa is a fairly-coarse gravel, the pebbles being quite firmly held together with a lime cement. Gold is scattered through this cement in particles ranging from fine specks to pieces several grams in weight, and occasional large nuggets are encountered. The contents vary so widely that it is difficult to estimate the average value, but returns of from $10 to $50 per cubic yard are common, and it is doubtful if the Indians considered anything less than from $4 to $5 a yard as "pay dirt." This argo masa occurs in channels varying in thickness from a few inches to several feet, and in width up to 300 ft.. These channels are continuous and are probably ancient stream-beds. They are for the most part covered with an over-burden of a more recent gravel, varying from 30 to 50 ft. thick, and the fact that this over-burden contains values as high as $1.50 per cubic yard, and yet was not worked by the Indians, shows that their idea of what constituted pay-ground was high.

Apr 1, 1911

By Rex B. McLellan

Studies of the eyuilibrzum between ferrite and austenite with gas mixtures (CO + CO2 and H2 + CHe) have been used as a means of deducing the energy and vibrational entropy of carbon atoms in dilute interstitial Fe-C solutions. A simple model for dilute interstitial solutions is given which enables a solubility equation for the equilibrium between the gas mixtures and the solid to be deduced. This solubility equation is used to estimate the partial In this work measurements of the equilibrium between dilute solid solutions of carbon in iron and gaseous mixtures of CO2 + CO and CH4 + Hp have been analyzed using theoretical solubility equations deduced from a knowledge of the thermodynamic parameters of the gas mixtures and an appropriate model for the solid solution. The solubility equations are deduced by equating the chemical potential of carbon atoms in the gas thermodynamic functions of dilute Fe-C solutions from the measured equilibrium between the solid and the gas mixtures. It is shown that the vibra-tional entropy of a carbon atom in a and y iron is smaller than the corresponding entropy 01. a nitrogen atom in solid solution inferrite or austenite and that there is little difference between the vibrational entropies of both nitrogen and carbon atoms in ferrite and austenite. and solid phases. The chemical potential of carbon in the gas is found from a simple statistical mechanical analysis of the gas mixtures utilizing spec-troscopic data while that for carbon in the interstitial solution is found from a model in which the carbon atoms act as bound oscillators distributed in a random fashion in the solution. The solid solution is dilute enough to enable solute-solute interactions to be ignored. Thus the configurational entropy of the solution is ideal but the mixing entropy contains additional excess terms due mainly to the vibrational changes occurring on solution formation. The partial excess entropies (and the partial energies) do

Jan 1, 1965

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:&apos; C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935

By R. W. Moore, A. B. Kinzel

Although the iron-carbon diagram has undergone many changes in the last 20 years, the region below the eutectoid line and up to approximately 1.7 per cent carbon has been little affected. This region is generally considered to consist of cenlentite and ferrite. Graphite has been noted occasionally in the hypereutectoid steel region, and the ready formation of graphite nodules in malleable cast iron is a phenomenon difficult to interpret in the light of cementite, supposedly stable at sub-eutectoid temperatures. In this case the graphite formation has been partly explained by the presence of silicon, and many have believed that silicon acts to change the stable state rather than to accelerate reactions so as to arrive at the stable state in a briefer period of time. Consideration of this phenomenon indicates that cementite is not the stable phase in the temperature composition zone referred to. In the course of examining a low-carbon steel tube taken from a petroleum cracking still, which had been in service for approximately three years at temperatures somewhat below the eutectoid temperature, observations were made that shed light on this entire subject. The tube in question analyzed:&apos; C, 0.15 per cent; Mn, 0.49; Si, 0.02; S, 0.023; P, 0.015. The microstructure of the tube after service is shown In Figs. 1 and 2. From these it is evident that cementite as such is absent, and that in its place nodular graphite has been formed. In order to check this observation further, samples taken from the tube were heated at 850" C. for varying periods of time. The small samples were put into a large hot furnace, and the total time is recorded. The structure of the sample after 5 min. at 850" C. is shown in Figs. 3 and 4, and the nest of pearlite surrounding the graphite nodules is most satisfactory evidence of the character of the nodules. As the length of time of heating at this temperature increases, the pearlitic zone increases, with final restoration

Jan 1, 1935