Search Documents

By Reynold Q. Shotts

Chemical methods, based on the relative rates of oxidation of fusain, bright coal, and dull coal by nitric acid, have been devised to determine these coal components.1-4 Results obtained by oxidation methods for fusain have been checked against results obtained from microscopic methods on duplicate samples of the same coals, but to the author's knowledge this has not been done for bright and dull coal components. For this reason it is not certain that the two methods of analysis identify essentially the same chemical or physical units. It would be highly desirable to see results of the application of both methods to duplicate samples, but in the absence of any such data the author has attacked the problem indirectly. From the U. S. Bureau of Mines samples were obtained of three Alabama coals which the USBM had analyzed optically and reported on over the past 30 years. These samples were subjected to analyses by oxidation rate methods. Results of this work, and comparisons with the USBM analyses, have been published. This was the first indirect approach to the problem. The present report attempts a second indirect approach by way of internal validation.

Jun 1, 1955

By Evans B. Mayo

As a result of studies distributed over the earth- including ocean basins as well as continents- some tectonists recognize four dominant structural trends: 1) northwest; 2) northeast; 3) nearly east- west, or equatorial; and 4) nearly north-south, or meridional. Baker' proposed a theory to account for these trends and Sonder5 called their world-wide arrangement the regmatic shear pattern. Moody and Hill6 proposed a much more complicated shear network which, although fascinating and perhaps ultimately useful, will not be followed here. In a recent review of deformation within the Cordillera, Wisser7 mentioned the four fundamental directions. The fact that many geologists deny the existence of the regmatic shear pattern implies that the fundamental structures are far from obvious. It may mean, also, that some geologists are not accustomed to examine regional and world maps analytically. The maps require much study, and certain features, should be isolated on overlays. Even so, with the present limited knowledge, uncertainties remain. The following analysis is a qualitative experiment, subject to change as information accumulates, and should be supplemented by the western sheet of the Tectonic Map of the United States.8

Jan 11, 1958

By Stanley Kesler

The first of two initial 650-mw units of the Paradise Steam Station, located on the banks of the Green River in the south-central portion of the western Kentucky coal basin, is scheduled for operation in late fall of 1962. This plant will be the eighth large-capacity, modern station built by TVA in a series starting with Johnsonville, operated first in 1951. During the subsequent ten years, unit sizes have increased from a capability of 125 mw to 650 mw at Paradise. This new unit will take its place in a power system that serves an area of about 80,000 sq miles with a present installed capacity of over 12,000 mw. Upon completion of the Paradise units and other additional hydro and steam units presently under construction, the system capacity will have reached over 15,000 mw. Projected load estimates indicate that this system will provide a margin of slightly under 10% of dependable capacity above peak demand at that time. One Paradise 650-mw unit at that time will represent approximately 4yc of the total system installed capacity.

Jan 10, 1962

By R. A. Foos

During the radium boom in the early part of the twentieth century, the basic chemistry of uranium was fairly well defined. Uranium production has progressed from the status of a radium by-product to a very important industry. With the ever increasing need for more efficient and cheaper methods of processing uranium ores, new techniques are being developed. Since uranium and vanadium often occur together in nature, the latter element will also be considered. As production rates, costs, and certain aspects of uranium chemistry are still classified by the Atomic Energy Commission, these will not be discussed. Domestic uranium deposits, in general, are composed of the minerals carnotite, which contains hexavalent uranium, and to a lesser extent, pitchblende and uraninite, which contain tetravalent uranium. Carnotite also usually contains vanadium. The uranium and vanadium contents of these ores vary considerably. The ores currently processed on the Colorado Plateau assay from 0.2 to 0.4 pct U and from trace amounts to 5.0 pct V. On the other hand, the phosphate rock deposits of the southeastern U. S., from which uranium is also recovered, contain only about 0.01 to 0.02 pct; processing of the

Sep 1, 1956

By J. Weertman

High-temperature creep experiments were carried out on indium, lead, and on binary substitutional alloys of In-Pb, In-Sn, In-TI, In-Cd, In-Hg, Pb-Bi, Pb-Sn, Pb-In, and Pb-Cd. The stress at which the power law creep equution breaks down was found to be much smaller for indium and lead than for metals with larger elastic moduli. The exponent over the stress in the power law creep equation was found to decrease upon alloying from values close to 4.5 to values near 3. THIS paper describes a set of high-temperature creep experiments made on high-purity lead and indium and on lead-rich and indium-rich single-phase binary alloys of various metals. These ex- periments were carried out to check two predictions of some creep equations derived by us"2 from a dislocation creep model due essentially to Mott. This model is shown in Fig. 1. Here dislocation loops are emitted from sources, not shown, situated on different slip planes. As the loops expand they come into each others' stress fields and are stopped. However, at high temperatures, as Mott has pointed out.

Jan 1, 1961

By Paul Billingsley

THE mining districts of the first and second order1 of the western United States (and borders) are those named on Fig. 1. These fall into four groups: (1) in the eastern outliers of the Rocky Mountain system; (2) in the Rocky Mountain system itself; (3) in the Great Basin; and (4) in the Sierras and Coast ranges. Of these four groups, the first three are almost entirely of Tertiary age and are within a belt of Tertiary compres-sive folding which we shall call the Rocky Mountain-Great Basin thrust arc. The backbone of this belt is shown by the line BAC. The position of the ore districts in this belt indicates a conformance to linear elements of the continental pattern. These are additional to the peripheral elements emphasized by Butler.2 NATURE OF THE THRUST ARC The thrust arc separates regions of contrasted kinds. To the east of it are flat-lying plateaus interrupted by earlier mountain folds; to the west, sunken basins, in which block-faulted ranges lie like an anchored fleet in a sea of desert wash or lava. The cross-sections are as shown in Fig. 2.

Jan 1, 1933

By Paul H. Johnson

Chemical mining may be defined as the use of chemicals in extracting metal values from in situ broken or unbroken ores within a mine. The present means for the generation and regeneration of sulfuric acid or sulfuric-ferric sulfate solutions are inadequate for most applications. This report describes a pressure oxidation process for the generation and regeneration of these solutions from pyrites and spent iron sulfate leach liquors. While recent mining developments such as solution injection, caving, and conventional and nuclear blasting, have provided new and better means for the per-colation of leach solutions through rock masses, little has been done to reduce cost and improve the quality of the leach solutions that are required. A leach solution for chemical mining should meet certain requirements. It should be 1) inexpensive on either a small or large tonnage basis, 2) capable of selectively leaching the desired ore minerals contained in a particular ore, 3) of the proper strength or quality to do the job of leaching in an underground environment and 4) amendable to simple and inexpensive metal recovery steps. It is also important that the capital investment be low for the solution generation and; or regeneration plant.

Jan 8, 1965

By Garth M. Crosby, F. McIntosh Galbraith, Bronson Stringham

THE Hercules mine is located in the northeastern section of the Coeur d'Alene district, approximately 1 1/2 miles north of the town of Burke, Idaho. Surface indications of the ore deposit were first discovered in 1886, but regular mine production was not started until 1902 and was continuous until April 1925, when the known ore had been extracted. Incomplete records show that from 1912 until operations were suspended the mine produced 2 1/2 million tons of ore containing 9.4 pct lead and 7.7 oz of silver per ton, together with an estimated 2 pct zinc, 0.3 pct copper, and 20 pct iron. This operation was the first in a series of mining enterprises culminating in October 1947 with the consolidation of Day Mines, Inc. In the same year it was decided to unwater the levels below the collar of the Hercules shaft in the hope of finding some indication of a recurrence of ore. The unwatering operation has been described in a previous paper.1 The initial exploration, following recapture of the workings, showed sufficient promise to warrant a detailed study of the mineralogy with modern techniques.

Jan 12, 1953

By Eugene P. Pfleider, Claus Freyberger

Generally, the different methods of financing new mining projects are not well understood by the engineers and supervisory personnel. Nor are the effects of these alternatives on depletion, taxes and profitability readily apparent to even the sophisticated management personnel without the aid of cash flow studies. Fortunately, with the advent of the computer it is possible now to simulate many different combinations of 1) equity, 2) loan and 3) production payment financing with little effort. A general computer program for cash flow analysis of mining ventures has been developed and applied as a case example to a 1967 feasibility study of the Underground Mining of Minnesota Taconite. The effects on profitability as measured both in rates-of-return and present value are presented for various financing combinations. In addition, percentage depletion rates were altered so as to measure the impact of this statuatory allowance. Based on the cost data as presented in the aforementioned 1967 feasibility study, and assuming 7% loans, the rates-of-return vary from 9. 9% to [00] % on equity variations and from 9. 9% to 11.4% on total invested funds.

Jan 1, 1969

LIEUTENANT MARTIN F. BOWLES Martin F. Bowles, born Apr. 25, 1893, at Bonne Terre, Mo., and graduated from the Neodesha, Kans., High School, had finished all but one month of a four-year course in metallurgical engineering at the Missouri School of Mines, Rolla, Mo., when on May 12, 1917, he entered LIEUTENANT MARTIN F. BOWLES. the first Officers' Training Camp at Fort Riley, Kans. At the close of the training period, he was commissioned a Second Lieutenant and as¬signed to Co. B, 355th Infantry, 89th Division, and stationed at Camp Funston. He left this camp with his company on May 21, 1918, and sailed from an eastern port on June 4, arriving in England on June 15, 1918. After a short stay at a rest camp there, he proceeded to France. On August 14, he wrote that he was with Battalion Headquarters as Scout Officer, 1st Battalion, 355th Infantry, 89th Division. The last letter received from him, dated September 2, was written in his dugout and contained the following: "Here it is 2.45A. M. Sitting in a dugout

Jan 1, 1919

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By K. S. Seljesater

Since the development of dispersion-hardenable lead-antimony alloys' in the laboratories of the Western Electric Co., Inc., studies have been made of the effect of various third constituents on these alloys.2 This paper covers a study of the effect of small amounts of arsenic. This element is important since it occurs as an impurity in many commercial antimonial leads and the results obtained are particularly interesting as indicating a class of addition agents which exert a stabilizing effect on dispersion-hardened alloys. Experimental In order to study the effect of increasing amounts of arsenic, a series of alloys were made up containing 1 per cent. antimony, and arsenic varying from 0. to 0.10 per cent., the balance Doe Run lead (99.997 per cent. lead). The alloys were cast into bars 1 1/2 in. wide by 3/4 in. thick and cold-rolled to about 1/8 in- thickness. Three samples of each composition were annealed 1 hr. at 225" C. and quenched in water. One set was aged at room temperature, one at 50" C., and the third at 100" C., the

Jan 1, 1929

By Frank Firmstone

The indicator cards shown herewith were taken by the writer in June, 1877, from the water-pressure blowing engine of the Longdale Iron Co., at Lucy Selina Furnace, Longdale, Virginia. A description of' this engine with figures, and some indicator cards, was published by Washington Jones, Esq., Superintendent of the I. P. Morris Co.,* in the Journal of the Franklin Institute for May, 1877, to which those desiring a full account are referred, but for convenience the principal dimensions, etc., are given below. The machine consists of a pair of horizontal direct-acting blowing engines, connected at right angles to a common fly-wheel shaft. The blowing cylinders are 4 ft. diameter by 5 ft. stroke; the water cylinders were 18 in. diameter by 5 ft. stroke as built. Both water and blowing cylinders are double acting. The water valves are balanced piston valves, 18 in. diameter, moved directly by eccentrics on the fly-wheel- shaft. Great care was taken to have the areas of the ports and passages at least equal to the area of the working piston. The engine is set about 14 ft. above the tail-race, and the

Jan 1, 1879

By L. O. Howard

Much work has been done recently on the lead-antimony system1 in connection with lead-rich alloys of commercial importance containing less than 20 per cent. antimony. Dean, Zickrick and Nix have called attention to the perpetuation in the literature of several erroneous data, such as a eutectic temperature of 228° C. at 12.5 per cent. antimony, instead of 247° at 13 per cent. The series is given as a classic example of a straight eutectiferous series in such late books as those of Heyn and Grossmann, 2 Jeffries and Archer,3 Guillet and Portevin,4 Pulsifer,5 Rosenhain,6 and Liddell,' as well as the somewhat earlier works of Hof-man (1918), Wang (1909), and Williams (1920). The work of Dean has definitely shown a solid solution of antimony in lead at about 2.5 per cent. antimony. While lecturing to a class in general metallurgy at the University of Idaho, the writer had the students prepare a series of lead-antimony alloys for the purpose of illustrating methods of thermal analysis. Proper proportions of powdered antimony (sold as C.P.) and test lead were mixed and melted in graphite crucibles under a reducing cover. Cooling

By Olav Idelgeland

FROM indirect evidence point defects have been believed to influence the fatigue behavior of metals and alloys.1,2 Measurements of changes in resistivity made after cyclicstressing at low temperatures indicate that a very high density of defects is present, part of which may be removed by room-temperature annealing.3'4 These results are consistent with the generation of a high number of point defects at low temperatures. Corresponding measurements made after room-temperature stressing did not show any recovery effects.3 This was attributed to a stabilization of the dislocation network after a few thousand cycles without generation of vacancies. In this laboratory resistance measurements of copper single crystals, shaped as normal fatigue specimens ,5 have been made with a Kelvin double bridge at room temperature during and after cyclic stressing at 80 cps by comparing with a dummy at a close and constant temperature. Temperature differences were measured to ±0.025°C with fine thermocouples taped onto the gage lengths. Potential leads were tin-soldered into small holes in the gage length to give stable values. Corrections for differences in temperature and changes in mean length of the specimen were made according to the formula:

Jan 1, 1968

By Dilip K. Paul, Charles H. Jacoby

The economic importance of salt domes has been recognized throughout the world, primarily because of oil and gas accumulations on their flanks, and to a lesser degree, for the value of their salt and potash. Recently they have become of value as hosts for cavities used to store hydrocarbons. In the near future we believe that their main value will be a source of geothermal energy. Although tremendous effort has been expended on the understanding of the geology and physical characteristics of the strata intruded by salt domes, relatively little energy has been exerted in the comprehension of the salt dome itself. Salt domes have long been recognized as a geological heat anomaly. With respect to other sedimentary rocks, salt is a good conductor of heat. Expressing values in 10-3cgs units, sedimentary rocks vary from 1.0 to 8.0; metamorphic rocks from 5.2 to 8.4 and igneous rocks from 3.1 to 9.8. Rock salt in its pure form has a thermal conductivity of 17. Thus a salt dome can be expected to act as a conduit bringing heat vertically from deep within the earth's crust.

Jan 5, 1974

By Felicia F. Peng

The computer graphic routines and digital simulation program of coal cleaning circuits have been developed in the Mineral Processing Engineering Department, West Virginia University. The functions of the program include computing, tabulation and graphing of 1) washability characteristics of raw coals, 2) blending, 3) Tromp distribution curves for two washer types-- water only and dense medium, 4) predicting the functional relationship of yield and qualities of clean coal product in individual and overall coal cleaning circuits in coal preparation plant, and 5) determining the optimal clean coal yield based on the market and environmental specifications. Amdahl 470 V/7A digital computer, Tektronic 4025 graphic terminal and Tektronix 4663 digital plotter with Fortran IV are used to achieve the goals. The simulation with the aid of graphic routine program of coal cleaning circuits is a useful tool for coal preparation engineers in evaluating the feasibility of proposed flowsheets, in investigating the effect of a modification in a unit operation of an existing plant, in analyzing the off-line optimization, and in comparing the alternative circuit control strategies. The coal cleaning process simulation with graphic routine can contribute greatly to the decision making processes of preparation plant design.

Jan 1, 1983

By W. H. Bassett, J. C. Bradley

In their paper on the directional properties in cold-rolled and annealed commercial bronze,' Phillips and Samans suggest that cupronickel, under distinctly different treatments, shows both "45" ears" and "90" ears. Fig. I shows the ears on some cupronickel cups made some 17 years ago for bullet jackets for small arms ammunition. In this case the material heated to 425° C. had "45" ears, while that annealed at 950°C. showed long "90" ears" when drawn with the same tools. The method of cupping, the shape of cupping tools, etc., were found to have very little influence on the earing tendency, but the deeper the cup was drawn, the higher the ears would be. Method of Manufacture Cupronickel cast bars were 1 in. thick. Ordinarily, they were rolled with numerous passes to a thickness of 0.4 to 0.2 in., according to conditions. They were then given a single intermediate anneal, and rolled to finish thickness, frequently 0.032 in. After a last anneal the material was cupped with a "cut and draw" operation. Progress of this is indicated in Fig. 2, illustrating five different stages at which the drawing

Jan 1, 1933

By Robert H. Richards

IT will hardly be worth while to spend time over the discovery of this mine, how lumps of galena, were picked up and brought to town, and how legends were told of an old mine from which Revolutionary bullets were made. This is an entirely new mine, with no evidences of former or ancient workings in its immediate vicinity to guide or attract the prospector. The first pit was opened in May, 1874. In August I made a visit to this pit, which was 6 feet wide in the northwest direction, 12 feet long north 80° east, and 6 feet deep. About 4 tons of a galena carrying gray copper, siderite, and quartz, had been taken fron this pit. The lumps were all of them evidently float specimens, and varied from 8 to 12 inches thick, and showed very distinct indica- * An abstract of this paper was kindly presented by Dr. T. Sterry Hunt at the February meeting of the Institute, but as it was not fully written out until the following December, it will describe the mine in a little more advanced stage than when the paper was originally presented.

Jan 1, 1875

By L. O. Howard

Much work has been done recently on the lead-antimony system' in connection with lead-rich alloys of commercial importance containing less than 20 per cent. antimony. Dean, Zickrick and Nix have called attention to the perpetuation in the literature of several erroneous data, such as a eutectic temperature of 228° C. at 12.5 per cent. antimony, instead of 247° at 13 per cent. The series is given as a classic example of a straight eutectiferous series in such late books as those of Heyn and Grossmann,2 Jeffries and Archer,3 Guillet and Portevin,4 Pulsifer,5 Rosenhain,6 and Liddell,7 as well as the somewhat earlier works of Hofman (1918), Wang (1909), and Williams (1920). The work of Dean has definitely shown a solid solution of antimony in lead at about 2.5 per cent. antimony. While lecturing to a class in general metallurgy at the University of Idaho, the writer had the students prepare a series of lead-antimony alloys for the purpose of illustrating methods of thermal analysis. Proper proportions of powdered antimony (sold as C.P.) and. test lead were mixed and melted in graphite crucibles under a reducing cover. Cooling

Jan 1, 1928