Search Documents

By J. T. Dewan

An experimental setup is described whereby the responses of Neutron logging instruments have been determined opposite formations of different porosities and under various borehole conditions. The results of these tests are presented in several charts which show how the Neutron log is affected by the following factors: hole diameter, casing, cement, salinity and weight of drilling mud, and position of logging tool with respect to the wall of the hole. The responses in the case of empty holes are also shown. A chart is furthermore presented which shows the shapes of the Neutron log, as a function of logging speed and time constant, at the boundaries between two formations with different porosities. These were derived mathematically using as a basis laboratory determination of the shape of the curve under static conditions, i.e. at very low logging speed. Corrections for the readings made opposite thin beds are given by these computations. The correction is found negligible under usual logging conditions for beds thicker than about 4 ft. INTRODUCTION The Neutron log is used in borehole surveys both for the delineation of porous formations and for the quantitative estimation of their porosities.1,2,3,4,5 It is common practice to calibrate the response of the Neutron log in terms of porosity values for each given geological unit by means of empirical comparisons between the deflections of the neutron curve and the porosity values given by the core analysis in a sufficient number of wells. Usually, the plots of the porosity values vs Neutron log deflections show a definite trend. It is therefore possible to trace an average line across the plotted points. This average line constitutes a calibration curve which can be used to evaluate the porosities from the Neutron logs in the other wells drilled in the same region. Futhermore, when the porosity values are plotted on a logarithmic scale and the Neutron log deflections on a linear scale, the calibration curve is practically a straight line. Accordingly the calibration curves are often determined by simply tracing a straight line between two points corresponding to two widely different porosities. Different choices are made for these two points, depending on local conditions. For example, one point will be defined by plotting the deflection of the Neutron curve opposite a formation known to be very tight, for which an average porosity value of 1 or 2 per cent is assumed. The other point may correspond to shale sections, to which a porosity of around 40 per cent is ascribed. The information provided by the eletrical logs — in particular the Laterolog, Limestone log or Micro-Latero-log — is also very often a help in the calibration of the Neutron logs. Empirical approaches such as these make possible the derivation of fairly reliable porosity values from the Neutron logs in many cases, at least in open holes and in essentially clean formations. There are, however, several causes of uncertainty which may sometimes entail appreciable errors. On the one hand, the Neutron log readings are influenced by the borehole conditions: hole diameter, presence or absence of casing and cement, presence or absence of drilling mud, characteristics of the mud, and position of the logging instrument with respect to the wall of the hole. The amplitudes of the curves opposite thin beds are furthermore atfected by the bed thickness,

Jan 1, 1957

By Oscar Johnson

The industry has been canvassed for information on methods of handling grinding steel at milling plants, an important subject overlooked in most descriptive articles on milling plant arrangements. The data collected are offered in this paper as a guide to designers and planners who have loading and storage problems to solve. WITH capacities of milling plants expanding from a few hundred tons per day to many thousand, replenishment of grinding media is an important phase of mill operation. Information on this aspect of milling procedure, solicited from several mining companies, is summarized here. At International Nickel's Copper Cliff concentrator the normally strenuous job of changing rods is considerably simplified by the use of the Garrow rod charging machine, Fig. 1. The overhead crane, Fig. 2, brings a bundle of rods, weighing four to a ton, to the loading platform of the machine, positioned in front of the mill. The rods roll one by one down the slight incline of the platform onto a conveyor which sends them into the mill. A modified version of the Garrow machine, Fig. 3, is used at the Federal mill of St. Joseph Lead Co. An overhead crane places the portable steel structure in position in front of the discharge end of any one of the five 9x12-ft rod mills. It then raises a bundle of about twenty 3-in. rods to the discharge platform of the charging machine. The rods are 11 ft 7 in. long and weigh about 278 lb. By tripping a lever the operator allows one rod at a time to roll onto the inclined rollers. A slight push by the operator sends the rod smoothly into the mill. The Union Miniére du Haut Katanga rod charging machine, Fig. 4, is mounted on a pair of wheels at the forward end with swiveling castors at the back for steering it to position for use or storage. Wheels are equipped with locking brakes to maintain the machine in position while it delivers rods to the mill. The device is made in two parts. The first consists of the base, which carries the supporting wheels, grooved rollers, and drive. The other part serves as the rod deck, which can carry up to six 3-in. x 12-ft rods. A short boom built integral with the base reaches through the mill trunnion and delivers the rods into the mill barrel. Three grooved guide rollers ,are provided to receive the rods from the sloping charging deck. One rod at a time is fed to the rollers and thus delivered into the mill. Two of the rollers are driven by 11/2-hp motor through a V-belt drive. The third roller is driven off the first by a single V belt in a groove below the rod groove and on the same center line. Rods are delivered to the charger by an overhead crane in bundles of three to six as needed. The power is supplied by cables plugged into power outlets, suitably located near the rod mill discharge end. The Oliver Iron Mining Co. uses a rod charger, Fig. 5, suspended from a monorail by cables. It is constructed .of structural steel and has two decks, each capable of carrying five rods of 4-in. maximum diameter. The rods ride in grooved free-turning rollers. Legs extending down from the mill end of the mechanism act as supports when the unit is ex-

Jan 1, 1955

By James M. Schopf

Gilbert H. Cady (Senior Geologist, Head of Coal Division Emeritus, Illinois State Geological Survey, Ur-bans)— Those coal mining and preparation engineers and operators who read this article will probably be most concerned with those parts which deal with the applied aspects of coal petrology in the fields of mining and technology. Actually the two categories overlap to such a degree that they are essentially one. The article appears to suggest that there are two points of veiw in the field of applied coal petrology. From one viewpoint the interest is in the attributes of the various macerals (Fig. 4)—vitrinite, exinite, and inertinite—-in terms of utilization (when the coal is burned, coked, gasified, hydrogenated, etc.). From the other point of view, assuming that the macerals do possess individuality in behavior, interest attaches to the possibility that coal of a particular type (maceral composition) can be prepared by discriminating methods of preparation and blending. Most of the 29 items listed for mining and technology can be assigned to one or the other of these two categories. Somewhat the same simplicity that resides in the items of the proximate chemical analysis is desirable for the petrologic analysis. This simplicity appears to be fairly well achieved by the group maceral device provided mineral matter is also included. At present, without fully adequate experimental substantiation, the three types of material represented by the group macerals vitrinite, exinite, and inertinite are regarded as sufficiently different in composition and properties so that the preponderance of any one type gives the coal distinctive properties provided it is not too high in rank. This appears to be increasingly true with coals of decreasing rank from medium volatile bituminous coals downward. The article reflects the great emphasis placed on the technique of descriptive coal petrology in America. Such description has resulted in a good understanding of the nature of the fundamental variability in the physical composition of bituminous coals. Such understanding has been attained very largely by the thin section technique used in coal bed profile analysis introduced by R. Thiessen after the manner suggested by the data assembled in Table 11. In contrast, the group maceral concept of coal analysis in terms of the categories indicated on the left hand side of Fig. 4 is particularly useful for broken coal analysis and applied coal petrology, in which evaluation is largely based on quantitative concepts. It is inadequately emphasized in this article that although the Thiessen procedure is suitable for the purpose of petrologic description in which texture and orientation are of critical importance, it is less well adapted to the technological uses of applied coal petrology. No doubt those persons whose interest may have been aroused in the possibilities of more refined coal preparation by this and other recent contributions to the literature of coal petrology will understand that certain technical aspects of coal petrology, particularly in the field of descriptive petrology, are still a matter of some controversy among the coal petrologists, but they will also appreciate that Schopf has made an important contribution to the field of coal petrology in America by pointing out that such petrology requires consideration of disoriented or broken coal samples and that results are expressed less in descriptive terms than in quantitative values with respect to the four types of material composing coal—-vitrinite, exinite, inertinite, and mineral matter. Unfortunately because so much American coal petrology has been descriptive of the coal in the bed there is a dearth of literature on applied coal petrology. Research and experimental data in this field are greatly needed.

Jan 1, 1959

By P. Dayal, L. S. Darken

THE migration of carbon in austenite under the influence of an electric current has been observed qualitatively several times.14 Lebedev and Guterman5 recently have reported quantitative measurements; their method consisted of welding a low-carbon to a high-carbon wire, passing current, and later estimating the carbon distribution metal-lographically. We believe the method reported in this paper is superior in principle since electrolytic migration and ordinary diffusion are not necessarily coupled as in the weld method; also for the first time the extent of migration is determined by combustion analysis for carbon. A uniform tubular specimen (S.A.E. 1045 or 1095) was mounted as illustrated in the figures. the whole assembly being in an atmosphere of purified nitrogen. Direct current (129 to 226 amp at 0.65 to 1.0 v) served as source both of heat and of potential gradient for carbon migration. The duration of experiment was 7.5 to 12 hr, during which time the temperature was controlled (±10°C) manually. The experimental conditions are indicated in the first five columns of table I. With this experimental arrangement, the temperature initially has a maximum value at the central plane. Also, in this vicinity (by virtue of the symmetry), the carbon entering any volume element is equal in quantity to that leaving; the loss or accumulation of carbon occurs near the electrodes since the carbon moves uniformly near the center and is "frozen" at the cold ends. Hence, providing the time of experiment is not sufficiently long to seriously influence the conditions at the central plane, carbon crosses this plane only under the influence of the electrical potential gradient and not under the influence of temperature or concentration gradient. The amount of carbon which has crossed this plane was determined by combustion analysis of the two halves of the specimen. The results of these analyses are shown in the sixth and seventh columns of table I. It will be noted that substantial amounts of carbon migrated from the anode portion to the cathode portion (except at 920°C, which temperature was too low to exhibit the effect in the allotted time). In spite of precau-tions taken, considerable decarburization occurred as may be seen by comparing cols. 8 and 5. In three cases (indicated by asterisks in table I) the specimen was ground on one side, polished, and examined metallographically before analysis. One specimen was normalized and re-examined. Micrographs of selected areas in specimens 4 and 6 are shown in figs. 1 and 2, respectively. Evidence of carbon migration from the anode toward the cathode is quite apparent. Fig. 2 shows abundant graphite as well as cementite in a region near the cathode. The temperature of this zone is estimated at about 800°C. In fig. 1, particularly in the micrograph on the extreme right (the right side of which is of unaltered carbon content), there is evidence of slight depletion of carbon in the immediate vicinity of the cathode as contrasted to the general increase in carbon of the cathode half of the specimen. Although this may be attributed in part to decarbur-ization, it is believed that it is occasioned also by thermal diffusion—migration (of carbon) from a cool to a hot zone4—a phenomenon superimposed upon the electrical migration. Evidence of carbon migration was visible particu-larly during the course of the high-temperature,

Jan 1, 1951

By S. L. Couling, D. J-P. Adenis

i2) twinning in poly crystalline magnesium does not usually occur homogeneously but is concentrated in localized regions or bands inclined at about 45 deg to the stress axis. These bands of twinning are in many ways similar to the Luders bands seen in mild steel alzd Al-Mg alloys. Within a hand the percentage of the volume twinned may approach 100 with no twinning outside the band. Bands are not produced in specimens of grain size a3 x 10-= in. or in samples deformed at temperatures 300°F. Annealing of heavily twinned regions leads to re crystallization textures markedly different from those found in the starting material. The exact preferred orientation appears to depend on the starting grain size, the amount of compres-sive strain and the manner in which it is introduced. MAGNESIUM, with its hexagonal crystal structure, deforms plastically at room temperature by a variety of deformation mechanisms, one of the most important of which is (1012) twinning. In single crystals such twinning occurs on compression parallel to the basal plane or tension perpendicular to it. In wrought polycrystalline magnesium, such as rolled sheet, the preferred orientation is such that almost all the grains have their basal planes nearly parallel to the sheet surface. Therefore, if sheet material is deformed by cold rolling or by tension in the plane of the sheet, deformation of the grains by (1012) twinning is not favored. On the other hand, twins form readily on compression parallel to the plane of the sheet as in a compression test, on the compression side of a bent sample, or at the outer rim of a drawn cup. The first part of this paper deals with the morphology of (1012) twinning in polycrystalline magnesium. Some aspects of this subject were covered by Barrett and ~aller.' Of direct bearing on the work to be reported here are the comments of Jetter' in discussion to Ref. 1. He shows that Mg + 1.5 pct Mn alloy sheet when bent about a transverse axis develops a pattern of transverse bands on the surface of compression. A longitudinal section through the sheet shows that the bands are wedge-shaped and inclined to the rolling direction. The bands were identified as "outcrops of regions in which deformation is localized as the result of the reorientation brought about by (1012) twinning". The second part of the paper treats the recrys-tallization texture of the specimens twinned by compression. Magnesium deformed and then annealed generally recrystallizes with no change in orientation.1'3'4 This statement is true provided that the amount of (1012) twinning occurring during deformation is small. In an isolated observation, Anse15 has shown that, when deformation produces much (1072) twinning, annealing causes new maxima to appear in the pole figure. The second part of the paper elaborates on this point. I) MATERIALS AND PROCEDURES All of the experimental work to be reported was done using the commercial sheet and plate alloy AZ31B (nominal composition: 3 pct Al, 1 pct Zn, 0.4 pct Mn, balance magnesium). This alloy is available commercially in two tempers, -0 (fully annealed) and -H24 (partially annealed), and specimens of both tempers were used in various experiments. The average grain. diameter (AGD) for -0 temper 0.125-in. sheet is about 0.5 x 10- in.; where material of larger grain size was desired, anneals at elevated temperature were used to grow the grains. compression tests were made on a screw-driven "hard" machine. The specimens were clamped in a

Jan 1, 1964

By J. L. Zakin, G. K. Patterson, J. M. Rodriguez

Correlation has been obtained between drag-reducing characteristics for turbulent flow in a pipe and measurable properties of several polymer solutions. Several concentrations of high molecular weight polymethyl methacrylate in toluene, high molecular weight polyisobutylene in both toluene and cyclohexane, medium molecular weight polyisobutylene in cyclohexane and benzene and low molecular weight polystyrene in toluene were studied. Data obtained in these nonpolar solvents and literature data for more polar solvents were successfully correlated as the ratio of measured friction factor to purely viscous friction factor vs the modified Deborah number vrl/D0.2 where 71 is the first-mode relaxation time of the solution estimated by the Zimm theory. A shift factor which is a function of intrinsic viscosity 1/(4[?] - 1) allowed all the data obtained with nonpolar solvents to be correlated as a single function. For these systems, most of the data fit a single curve to within + 5 percent of the average friction factor ratio. The shift factor did not give a unique function of the data for the more polar systems. INTRODUCTION The phenomenon of drag reduction in polymer solutions was first studied by Toms1 in dilute solutions of polymethyl methacrylate in mono-chlorobenzene. The drag ratio for flow through circular tubes has been defined2 as the ratio of the pressure. drop of the solution to the pressure drop of the solvent at the same flow rate. The drag ratio is less than 1.0 for a drag-reducing fluid. Practical use of drag reduction is being made in fracturing operations in the petroleum industry.3 A more fundamental quantity is the friction factor ratio, defined as the ratio of the observed pressure drop to that predicted for a solution of the same viscosity characteristics and density at equal flow rates using the Dodge-Metzner friction factor equation4 Viscous solutions with drag ratios greater than 1.0 can have friction factor ratios less than 1.0. For practical applications, it is drag reduction which is of interest. However, for correlation the fundamental ratio is the friction factor ratio. In recent years, drag reduction has been studied extensively. Recent studies have shown that reasonable predictions of the incipience of drag reduction in polymer solutions can be made from the properties of the solutions and the flow Variables.5 However, it has not been possible to predict accurately the amount of drag reduction to be expected for a given polymer solution without any drag-reducing turbulent flow data on the same solution.6 For flow through circular tubes it is well established that there is a concentration effect and a diameter effect on drag reduction. Toms1 observed that drag reduction increases with an increase in the concentration of the solution up to an optimum concentration beyond which, due to the increased viscosity of the solutions, the drag ratio increased with an increase in concentration. Hershey 7 observed that for dilute Newtonian polymer solutions in nonpolar hydrocarbon solvents, a normal transition region may be obtained followed by a departure from the von Karman equation (on a friction factor-generalized Reynolds number chart). The point of departure is a function of diameter: the smaller tubes depart at the lower Reynolds numbers. Concentrated solutions may show no abrupt transition region, but merely an

By W. L. Falke, A. A. Cochran

A basic problem in connection with manganese is to find economical ways to utilize domestic resources. As a part of its program to conserve domestic mineral resources and to reduce dependence of foreign sources, the Bureau of Mines had conducted extensive research to broaden manganese technology and to find economical, technically-feasible processes for recovering manganese from these low-grade resources. This paper analyzes some of the major difficulties which have been encountered in previously proposed processes for treating low-grade manganese ores and discusses a process which may circumvent many of these difficulties. Vast deposits of low-grade manganese ore exist in the U.S., yet domestic production is insignificant compared to the more than 2 million tons of ore imported yearly into this country.' A basic problem in connection with manganese is to find economical ways to utilize domestic resources.2 As a part of its program to conserve domestic mineral resources and to reduce dependence on foreign sources, the Bureau of Mines has conducted extensive research to broaden manganese technology and to find economical, technically feasible processes for recovering manganese from these low-grade resources. Although a great many processes have been proposed for treating domestic manganese resources, a failing of many of them is that too many steps are involved for economical operation.' Some of the major processes that have been proposed were reviewed by Norman and Kirby.3,4 Chlorination processes have become increasingly useful as a means of recovering valuable metals from raw materials, because the relative cost of chlorine (Cl2) and hydrogen chloride (HC1) has decreased through the years, and because the corrosion resistance of materials of construction has been improved. The objective of these processes is to form metal chlorides that are more volatile or water-soluble than are the corresponding oxides or sulfides; these compounds then can be separated from the gangue or other minerals by volatilization or leaching. Several chlorination processes for the recovery of manganese have been investigated by the Bureau of Mines5-8 and others; the major chlorination processes were reviewed in 1963, and their main features were compared.4 In all these processes, the simultaneous leaching or volatilization of iron chlorides with manganese chloride (MnCl2) is a problem, and the more iron that is present, generally the greater the problem. The leaching step is not highly selective, and the product of this step is, at best, suitable only for the production of ferromanganese or for further processing to remove iron. The product of the volatilization step is, in all cases, a mixture of iron and manganese chlorides that contains too much iron even for ferromanganese production, and must undergo additional processing steps for iron removal. THERMODYNAMIC CONSIDERATIONS The literature indicates that the desired chlorination reactions will proceed at practical rates at temperatures near 1200°K (927°C). Free energy changes at 1200°K for the critical steps of the reduction and chlorination reactions9-11 follow: Most of the research on chlorination processes for manganese recovery has been done with HC1 rather than with C12, for the following three main reasons: 1) Recycling of the chlorinating agent, which is economically vital, appeared to be easier for HC1

Jan 1, 1968

By K. Torssell, U. Lindborg

The kinetics of precipitation deoxidation is considered from a theoretical point of view. The size distribution and the total content of deoxidation products are estimated statistically as a function of time, taking into account Stokes and gradient collisions between the particles and separation at the top surface of the bath. The assumption is made that two particles coalesce into one larger particle as a result of a collision. General expressions are derived and calculations are carried out numerically for the case of silica particles in liquid iron. The analysis predicts a three-stage behavior for the removal of oxygen, an incubation stage, a stage of rapid separation, and a slow final stage where the content approaches the equilibrium value. The agreement with experimentally determined size distributions and deoxidation times is considered to be good. A quantitative estimation of such growth mechanisms as diffusion from the melt and redistribution of oxygen from small particles to large ones shows that these latter mechanisms cannot explain the experimentally observed gvowth of inclusions. This also indicates that collisions provide the important growth mechanism. OXIDE inclusions precipitate when a deoxidizer like silicon or aluminum is added to a steel bath. The inclusions grow and the large particles tend to separate from the bath. For each type of oxide the growth determines the sizes of the final inclusions as well as the total inclusion content of the steel. The mechanism of growth is controversial, however. It has been suggested that an inclusion grows principally by diffusion of atoms through the melt to the inclusion particle or principally by collisions and coalescence with other inclusions. Diffusion growth is always present to some extent but recent experiments and calculations by Torssell,' Kniippel et 'a1.,2 Sano et al. and Miya-shita4 indicate that collisions may be more important than previously realized. A detailed analysis has so far been lacking. The present paper is a quantitative, statistical analysis of the growth and separation of inclusions and is based on a collision theory. Nuclea-tion is not considered. The numerical estimates are based on the experimental conditions of Torssell's' investigation and comparisons are made with his observations. Torssell' studied the growth and separation of silica particles in liquid iron. Samples were taken from a 0.6 kg iron bath at various times after the addition of silicon. By a particle-counting technique developed by Bergh and Lindber~the size distribution of the inclu- sions was determined. The number of particles at the first sampling, 10 sec after silicon addition, was of the order of 3 x lo7 to 10' per cu cm, the largest particles having a radius of 2 to 4 pm. The volume fraction was 0.001 to 0.004; i.e., the dispersion was very dilute. During subsequent holding the largest particles increased their radius by a factor of 10 after about a minute, and the whole size distribution was displaced toward larger values. These results were obtained with allowance for precipitation of the equilibrium concentration of oxygen during solidification. The bath contained less than 0.01 pct of C. Figs. 1 and 2 show the typical appearance of the inclusions. Most particles are very closely spherical and appear to have been liquid or semiliquid in the melt. The observed number of inclusions, about 5x 10' per cu cm, is of the same order of magnitude as found by ~er~h.' This is a large value. It follows that the diffusion distances are very short and that the precipitation

Jan 1, 1969

By C. W. Haworth, M. G. Hall

THE diffusion of copper in silver has been studied by Sawatzky and Jaumot1 and Cahoon and Youdelis.2 Sawatzky and Jaumot measured tracer diffusion in single crystal specimens but the 12.9 h half-life of CU64 limited the time of the diffusion anneal to about 50 hr, and in consequence the minimum temperature of the investigation was 716°C. Cahoon and Youdelis employed polycrystalline diffusion couples, and measured the interdiffusion coefficient over the range 0 to 2 at. pct Cu. These experiments were performed at temperatures down to 630°C and a discontinuity in the Arrhenius plot was observed at -700°C. The high D-values at lower temperatures were attributed to the effect of grain boundary diffusion. The present experiments were undertaken to investigate this anomaly and study the low temperature region of the diffusion of copper in silver. The method employed single crystal samples and a plated source of copper. Silver single crystals 2½ by 4 in. sq were grown from zone-refined silver bar (>99.99 pct Ag) by the Bridgeman technique, and $ in. thick slices were cut by spark machining. The specimens were electro-polished, and a 2 µm layer of copper was electroplated on to the planar surface at one end of each specimen using a potentiostatic voltage source. The following solution was used for plating: CuSO4 . 5H2O 125 gm H2SO4 (S.G. 1.8) 53 ml H2O 1000 ml The diffusion couples were sealed in capsules, in an argon atmosphere, and were annealed at either 701, 597, or 498°C. The temperature measurements were made to an accuracy of *l°C After the anneal, the penetration of copper into the silver was determined using an electron probe micro-analyzer. 100 sec scaler measurements of the intensity of Cu Ka! X-radiation were performed at 2 to 5 µm intervals along a line normal to the source, with a beam potential of 25 kv. Allowances were made for the background radiation, and the dead-time of the counting system in the normal way, and the intensity ratios were corrected to weight concentration by the method of Duncumb & de-Casa.3 For the analysis of the diffusion profiles, it was first observed that the copper layer did not completely dissolve in the host crystal for the specimens annealed at 498 and 591 whereas for the specimen annealed at 701°C, a single phase solid solution was formed. For the 498" and 597°C specimens, the concentration of copper in the silver at the interface was therefore constant throughout the anneal and the analysis for a

Jan 1, 1970

By J. B. Cohen, M. B. Beaver, R. J. Black

RECENT investigations have shown that face-centered cubic metals may deform by twinning. Blewitt, et al' found that at 4.2"K the mode of def~rmation of single crystals of copper changed at large strains and markings formed on (111) planes. Later they- emonstrated by X-ray diffraction and metallography that the markings were twins and showed that favorably oriented single crystals of copper deformed by twinning at 78°K. They also observed twinning in silver and gold deformed at 4.2 and 78°K. Wagner3 obtained evidence for twinning from the peak shape of diffraction lines of silver cold-worked at 78°K, but twins small enough to cause such effects are not likely to be detected metal-lographically. In the work reported here lamellar structures were observed in deformed silver-gold alloys. They appeared to be mechanical twins, but metallography could not establish this conclusively. Their tendency to form depended on strain rate, temperature and composition. Specimens of silver-gold alloys (0 to 83 wt pct Au) were deformed plastically. One set was worked by hammering under liquid nitrogen, at room temperature and at intermediate temperatures. Another set was compressed slowly in liquid nitrogen to the same reductions as those produced by hammering. Tensile specimens (0.015 x 0.120 x 1.5 in.) of various compositions and approximately equal grain size (0.011 to 0.016 cm) were tested at -195°C and at room temperature. In microsections of all specimens deformed by hammering at —195°C thin lamellae appeared, Fig. 1. They were aligned in definite directions in each grain. In some grains they had two orientations. Where lamellae intersected, a displacement was apparent. Near the center of the left margin of Fig. 1 shear has taken place beyond the fully developed intersecting lamella. Many lamellae resembled Neumann bands in alpha iron. They were parallel to one side of triangular etch pits in the matrix (as in Figs. 1 and 2). The individual lamellae were narrow and had little substructure. This suggested that they did not result from concentrated local slip. The shape of etch pits within the lamellae differed from that of pits in the matrix, as can be seen in Fig. 2; this indicated a difference in orientation. Specimens slowly deformed at —195°C contained regions in which the lamellae were clustered. In these specimens some lamellae were bent and presumably had formed before the termination of the deformation. Structures of greater width than the lamellae were also seen.4 More lamellar structures formed on impact than during slow compression to a given reduction. This was true of all compositions. The structures became less abundant with increasing temperature of deformation. None was observed after extension to fracture at room temperature, but they could be pro-

Jan 1, 1959

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By Oliver C. Ralston, Foster Fraas

Electrostatic methods of separation are used only when some peculiar advantage is gained. Such cases are minerals that are not separable by differences in specific gravity or magnetic response and that are desired in particles as large as 10-mesh, a size on which flotation separation is inefficient. This paper covers several separations of this type and others. It includes studies in the electrostatic behavior of kyanite, sillimanite, and zircon, simple silicates that cannot be called either acid or basic but are more nearly neutral. Kyanite and sillimanite are both desired in 10-mesh size and are difficult to bene-ficiate from low-grade ores to give that type of concentrate. A separation of garnet from diopside was studied because this mixture had been removed from a wollas-tonite product by drying and magnetic separation, and no special or extra-preparation for electrostatic separation was necessary. The Separator The separator used in these tests is of the nonhomogeneous field type shown in Fig Ia. It consists of a 11.4-cm-diam rotating metal roll 2 at ground potential over which the dry mixture of minerals is fed. The roll serves as one electrode of the separating field, and the other electrode is that of 3, a smaller 5-cm-diam rotating metal cylinder which is held at a high direct-current potential. In this paper the term "electrode" will be confined to the electrode at 3, roll 2 being designated only as "roll."

Jan 1, 1949

By George J. Young

DURing the spring of 1910 1 visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. Thc principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories. The commercial deposits are confined to the Tertiary period although

Jan 1, 1916

Roof Bolts An expansion shell and plug Westinghouse roof bolting assembly made for use with threaded steel rods and large flat washers or steel channel employs a plug larger in diameter than those for trolley wire service. The notched plug helps prevent shell and plug from turning. The unit is shipped complete. Circle No. 1 Fan The Jeffrey Mfg. Co. Aerodyne Midget fan is a self contained blower or exhauster for auxiliary ventilation through tubing. Operating rating with 5 hp motor is 6.5 in. maximum static pressure, and 6200 cfm free delivery volume. Weight is 340 to 475 lb and it may be furnished in open or permissible form. Circle No. 2 Heavy-Density Initial installation in the Mesabi Range country of the Wilmot-Daniels heavy-density concentrating system was a 175 ton per hour plant at the [ ] Skubic Bros. Virginia, Minn., operation. This Wilmot Engineering Co. unit has a separatory vessel providing unidirectional medium flow and as the only moving part uses a standard drag-line conveyor for lifting sink out of the bath. Circle No. 3 Portable pH Meter A low priced battery-operated portable pH meter of utmost simplicity announced by the Photovolt Corp. uses only 3 ordinary radio batteries which give over 2000 hours of service. Accuracy of 0.03 pH is claimed by the manufacturer for the model 125, and AC power line supply is available. Circle No. 4

Jan 1, 1952

By W. J. Nelson, R. B. Nance

Detailed underground geologic mapping at a scale of 1:1200 has been carried out at the Crown II Mine of Freeman United Coal Mining Co., which operates in the Herrin (No. 6) Coal Member. The roof sequence, upward from the coal, includes (1) soft, medium -to dark-gray shale; (2) hard, black, fissile shale; (3) argillaceous nodular- bedded limestone, and (4) fine-pined, shaly, water-bearing sandstone. The first unit is highly lenticular, and any or all may be missing at a given locality. The sandstone has a sheet facies and a channel facies. The Herrin Coal is eroded in channels near the Crown II Mine. Structural features mapped at Crown II include normal and strike-slip faults and limestone "bosses." Less stable roof and wet conditions are encountered where the limestone is thin or missing or where it is broken by natural fractures or by artificial openings that intersect the water-bearing strata above the limestone. Geologic mapping of the underground workings has allowed us to predict faults, fracture zones, and channels ahead of the face for this mine. Some lithologic and structural pattern apparently are random and cannot now be projected. Conventional exploratory drilling is entirely inadequate to map faults or lithology of the roof, but it does indicate the range of lithologic variability, which can be used to project needs for roof supports. Drilling also is useful in locating channels and in mapping regional variation in thickness and facies of the sandstone.

Jan 1, 1983

A High-speed Dilatometer and the Transformational Behavior of Six Steels in Cooling. By Arthur L. Christenson, Edward C. Nelson and Clarence E. Jackson. (With discussion).................................606 Dilatometric Studies of the Graphitization of Cast Iron. By N. A. Ziegler. With discussion) 627 An Interferometer Type of Dilatometer and Some Typical Results. By- L. '4. WIlley and W. L. Fink. (With discussion).........................642 The meeting was held in the Pine Room of the Statler Hotel, Cleveland, Ohio, on Tuesday afternoon, October 17, 1944. The chairmen were F. M. Walters, Jr. and Howard Scott. Introduction F. M. Walters, Jr.—The principal advantages of the dilatometric method perhaps are two, as compared with the method of thermal analysis. One is that the dilatometric method can be applied with a large variety of rates of heating and cooling, whereas thermal analysis—that is, the study of the transformational characteristics by means of heat evolution—is limited to the rates of heating and cooling that reveal the evolution of heat. The dilatometer can be used for the study Of reactions at zero rates of heating and cooling; that is, isothermal reactions. As you will hear this afternoon, the rates have been pushed up as far as 500°C. a second. The other advantage is that the dilatometric method shows that a two-phase region is a two-phase region, whereas the thermal analysis merely reveals the temperature at which the rates of heat evolution are greatest.

Jan 1, 1945

By Carroll F. Hardy

The day by day loss of industrial plants to gas and oil is chiefly by default. The coal industry is not selling its superior economy, safety, and other advantages to its customers. THE position of the coal industry has been affected by a wide variety of developments in the production and use of energy. The tempo of development and change has been increasing and the end is not in sight. Legislation is currently being proposed for commercial use of atomic power, and the employment of atomic energy in significant quantity will probably occur about the same time as the decline in production of petroleum and natural gas. But these developments are in the future and have little immediate effect on utilization and marketing of coal. While no one should try to suppress or retard the development of a new and economical source of energy, both the coal and private utility industry should be allowed to question how the nuclear power is to be used, who is to use it, and who is going to pay for it. The taxpayers have a monopoly on fissionable material and the knowledge to employ it. Any commercial use must stem from this source. It is not hard to visualize either taxpayer-subsidized private utility atomic power plants on one hand and super TVA's on the other. In view of the gains of gas and oil in the home heating field, it is interesting to compare the 1940 and 1950 census reports on the kind of fuel used for heating in occupied dwelling units. Table I shows that whereas coal provided 77 pct of the fuel for central heating (furnaces and boilers) in 1940, it was down to 45.4 pct in 1950. However, only about 1 1½ million units were lost in this 10-year period. In the non-central heating category, which principally includes stoves, the percentage declined from 39.2 to 25.6, but the units declined about 2½ million in number. The big increase was in heating units designed to burn gas and oil. Use of wood for central heating declined about one-third. Data on amount of fuels used for residential heating are not available, but information is on hand for residential and comnlercial space heating, see Table 11. Commercial space heating includes office buildings, churches, schools. and similar structures. The annual use of bituminous coal in these two categories declined about 1 million tons in the 10-year period. Other forms of solid fuel showed greater losses, except wood, which remained the same. Domestic stokers reached their high point in 1948 with about 1,200,000 in use. At the end of 1951 there were approximately 1,116,790 stokers in use. Conversions to gas and oil have been from hand-fired heating plants in the ratio of about 7 to 1 compared to stokers. In other words, for every one stoker which has been converted to gas or oil, seven hand-fired units have been converted to gas or oil. A bare recital of these data would indicate that the coal industry is holding its own reasonably well. However, 93.4 pct of the new homes built in 1951 were heated by gas or oil. Oil-burning equipment was installed in 37.8 pct and gas equipment in 55.6 pct of the new homes. This indicates that the public prefers gas when it is available, and that oil is second choice, with all forms of solid fuel apparently used when it is unavoidable. It must be pointed out, however, that during the period of rapid expansion of gas pipelines gas has been sold for house heating at prices that are in some cases actually lower than coal prices, or very nearly on a par. Gas has been sold at wells at far below the comparable price for oil produced from the same wells, and far below its actual worth. This situation is being remedied at the present time by increases in gas prices at the wells. For example, the wellhead price of gas in Texas averaged 7.494 per Mcf in 1952. In 1949 it was 4.59c per Mcf. This increase in price is being reflected in pipeline gas prices, and in most of the markets served by the pipelines the tendency is to get it out of the bargain basement type of sales. The American Gas Association estimates that at the end of 1952 there were in the United States about 11 million customers for gas house-heating, and the Association expects additional gains each year until around 18 million homes will be heated by gas in 1975. By 1975 there should be 60 million dwelling units to be heated in the United States, if dwelling units increase at the same rate as the population. If the gas industry heats 18 million dwelling units by that time, this still leaves 42 million units to be heated by some other fuel. If oil is used to heat 18 million dwelling units in that same year, 24 million would of necessity be heated by coal, coke, wood, electricity, or another fuel. The total number of dwelling units using coal listed in the 1950 Census was 18,776,000, so it would appear that coal has a chance at least to stand still in the tonnage sold for domestic use. In the first quarter of 1953, 2044 domestic stokers

Jan 1, 1955

By J. M. Snook, F. C. Langenberg

FOR a better understanding of the melting and refining processes, the oxygen content of the steel bath should be determined. The oxygen content influences many process and product variables such as the efficiency of alloy recoveries, the ingot structure (through reaction with carbon in the steel), certain reaction rates, cleanliness (formation of indigenous oxide inclusions), and mechanical properties. Many methods of sampling liquid steel for oxygen have been devised. These methods can be divided into two main groups: 1) taking samples directly in the furnace or ladle;'-'0 2) removing the metal from the furnace or ladle in a sampling spoon and pouring it into a mold, or drawing the metal from the spoon into a sample holder.11-l4 The advantages and disadvantages of the two general sampling methods are presented in Table I. The bomb-sampling technique described by Huff, Bailey, and Richards8 has been used by the Crucible Steel Co. in certain research projects where oxygen contents were needed. It was recognized that a localized boiling condition could result when the mold is introduced into the steel bath, although the work of Gilbert and Bailey9 seems to indicate that the carbon boil occurring in the bomb-sampler cavity has a negligible effect on the oxygen content. In order to confirm the reported negligible effect of a carbon boil, additional work was done with adaptations of the conventional bomb sampler. The methods used are shown in Fig. 1 and are as follows: 1) Type A: aluminum wire (0.125-in. diam) coil in cavity; steel cap over mouth 2) Type B: aluminum cup in cavity; aluminum cap over mouth, 3) Type C: aluminum cup in cavity; steel cap over mouth, 4) Type D: fine aluminum wire (0.013-in. diam) in cavity; steel cap over mouth. The amount of aluminum wire in the Type A and D samples varied from 0.8 to 1.2 pct of the sample weight. The aluminum cups averaged 2.0 pct of the sample weight; the latter were used to ensure that the steel contacting the walls of the bomb cavity was fully killed. Samples were taken from plain carbon heats made in open-hearth furnaces. This grade of steel before silicon additions is essentially an Fe-C alloy and the effects of other alloying elements on the oxygen activity can be neglected. The results of sampling with the bomb samplers is shown in Fig. 2 where the percent oxygen is plotted against the percent carbon on log-log paper. Spoon sample results on the same grade of steel where the sample was killed in the spoon are shown in Fig. 3. The oxygen contents were determined by the vacuum fusion method. A comparison of Figs. 2 and 3 shows that the oxygen concentrations obtained with the spoon-sampling method (metal killed in the spoon after slag removed

Jan 1, 1960

By H. I. Aaronson

Isothermally formed plates of proeutectoid a, lengthen at approximately the rates predicted by the Zener-Hillert equation, indicating that their lengthening kinetics are controlled by the volume diffusion of chromium in the ß matrix. Solution annealing treatments in the vicinity of the transus introduce a second mode of transformation, in which the lengthening rate is at least 1.8 x 104 faster than predicted by this equation. Little or no volume diffusion appears to accompany the latter transformation. The Presence of oxygen is evidently a Prerequisite for the occurrence of this reaction. X HE effects of thermal history prior to the initiation of transformations which proceed by nucleation and diffusional growth are currently evoking considerable interest. The rate of nucleation (but not the rates of growth) of pearlitel and of bainite,2 and the over-all rates of aging reactions in Al-cu3 and Al-si4 alloys have been shown to be appreciably dependent upon thermal history in the solid-solution region"' or in the two-phase region prior to the onset of pre~ipitation.3,4 In none of these reactions, however, was the transformation mechanism changed by variations in the temperature-time path used to reach the reaction temperature. Preliminary experiments reported by M. K. McQuillan5,8 and a systematic investigation by Farrar and Margolin7 have disclosed that the transformation behavior of hypoeutectoid Ti-Cr alloys is considerably more sensitive to thermal history. Qualitative evidence strongly suggests that not only the rate of nucleation but also the rate of growth and even the mechanism of the ß — a reaction can undergo remarkable changes when a solution annealing treatment in the vicinity of the ß/a +ß, or transus temperature, is interposed between a high-temperature solution anneal (conventionallq at 1000°C) and the isothermal reaction treatment. The present investigation was undertaken in an attempt to ascertain the nature and origin of these effects. Study of the changes in the kinetics and morphology of the ß - a, reaction produced by varialtions in thermal history was the primary means employed for this purpose. EXPERIMENTAL PROCEDURE The compositions of the alloys used in this in~esti~ation are given in Table I. These alloys were homogenized for 5 days at 1050° C in evacuated (2 x 10 -5 mm of Hg), zirconium-gettered fused quartz capsules. The capsules themselves were enclosed in a porcelain chamber evacuated with a mechanical pump during the homogenization anneals. Upon completion of homogenization, the alloys were cooled to room temperature and then reheated to 550°C for 3 1/2 days in order to transform the alloys to a finely divided mixture of a and TiCr2, and thus provide an approximately constant initial mi-crostructure. Individual specimens were sealed in evacuated and internally gettered Vycor capsules and heat treated as previously described.8,9 EXPERIMENTAL RESULTS Ti-10.64 Pet Cr. This investigation was largely performed on the 0.64 pet Cr alloy. The "base"

Jan 1, 1962

By F. N. Rhines, W. S. Pellini

In many of the otherwise well established alloy phase diagrams the solidus curves (temperatures at which liquid first appears upon melting) have not been located accurately, chiefly because the experimental techniques that have been most popular for determining solidus temperatures have been both cumbersome and subject to large errors. C. E. Homer and H. Plummerl have described a sensitive and at the same time a very simple technique for locating the solidus curves in a number of alloys of tin. Their method consists simply in noting the temperature at which a specimen of the alloy ruptures under the influence of a light bending force. Although this method is not new, it has been little used for this purpose in the past; nevertheless, it appears so attractive in its possibilities of speed, simplicity, and precision that the investigations presently to be described were undertaken to verify its merits. The redetermination of the solidus and eutectic temperatures of the lead-antimony system was employed as a medium of experimentation. New values obtained in this way are believcd to be sufficiently precise to warrant a revision of the currently accepted lead-antimony phase diagram (Fig. I). Determinations of the solidus of the lead-rich lead-antimony alloy series have been published by X. S. Dean2 and by E. E. Schumacher and F. C. Nix. Their points are represented in Fig. I. In their work the solidus was not located at antimony collcentrations greater than 2 per cent; the curve was presumed to meet the eutectic horizontal at an antimony concentration of about 2.5 per cent. In the present studies the solidus has been traced to 3.5 per cent, where the eutectic horizontal is intersected (Table I and Fig. I). Within the range investigated by Dean and by Schumacher and Nix the agreement with their values is good. H. Seltz and B. De Witt,4 on the basis of activity measurements, have calculated that the intersection of the solidus and the eutectic reaction horizontal should lie at 3.86 per cent of antimony. The following determinations of the eutectic temperature have been reported: Roland-Gosselin,5 228°C.; Ewen,6 228OC.; J. E. Stead,7 24g°C.; Campbell,8 228°C.; W. Gontermann,9 245' to 252°C.; R. Loebe,lo 245°C.; E. Heyn and 0. Bauer,ll 245°C.; H. Endo,12 250°C.; R. S. Dean,= 247' to 258°C.; E. Abel, O. Redlich, and J. Adier,13 245°C.; W. Broniewski and L. Sliwowski,14 250' to 252°C.; H. Seltz and B. De Witt,4 25o°C. A temperature of 247°C. appears to have been generally accepted in recent years; it is the value most frequently obtained by the method of cooling curves. Values below 247°C. have usually been obtained by inferior cooling-curve techniques; those above 250°C., by the method of heating

Jan 1, 1943