Search Documents

By F. V. Lenel, J. A. Dromsky

The influence of thermal and mechanical treatments upon the elevated-temperature stability, the microstructure, and the mechanical properties of aluminumaluminum oxide alloys is investigated. Compacts from atomized and flake aluminum powders were sintered at temperatures just below the melting point of aluminum in a vacuum of 10-4 Torr for several hours and were then hot-extruded. During this treatment the hydrated oxide present on the surface of the powder particles decomposes, the water vapor produced reacts with the aluminum forming additional oxide, and the hydrogen developed is removed by diffusion to the surface. Extrusions of compacts so treated are stable at temperatures up to the melting point of aluminum and do not form blisters and internal defects typical of extrusions from untreated powder. Electron micrographs of extrusions from unsintered compacts show long parallel oriented platelets typical of the IN previous investigations1,2 the properties and structure of aluminum alloys were described which had been produced by cold compacting aluminum powder and then hot pressing and extruding the compacts. Both the structure and the properties of these alloys differ significantly from those of commercially produced aluminum-aluminum oxide alloys. When commercial alloys are produced, they are given a sintering treatment in air at about 600°C between cold compacting and hot pressing.3 During this treatment the hydrated oxide, which forms the coating on the aluminum-powder particles from which the alloys are prepared, is decomposed.4 The chemically bound water which is released reacts with the aluminum and forms aluminum oxide and hydrogen. Most of the hydrogen is eliminated by hydrated oxide skins on the original powder particles, while the oxide particles in extrusions from sintered compacts are broken up. The strength of extrusions from treated powder is somewhat lower, but their ductility is considerably improved over that of extrusions from untreated powder. The slip-trace patterns on electron microgvaphs of extrusions which had been strained in tension before replication indicated that the grain size of the extruded alloys was approximately the same as that of the original powder particles. Coarse-grained alloys were produced by severe cold work and annealing of the extrusions. They have significantly lower room-temperature strength, but about the same ductility as the vacuum-sintered fine-grained alloys. The size and shape of oxides in the coarsegrained alloys is similar to those of the fine-grained alloys, but the particles are somewhat more uniformly distributed. diffusing to the interior or exterior surfaces of the compact, but it is difficult to eliminate all of it because the solubility of hydrogen in solid aluminum is very low even near its melting point. Extruded alloys which are not sintered before hot pressing and extrusion appear quite sound upon metallo-graphic examination, but develop severe surface blistering and internal fissuring when they are heated to elevated temperatures after extrusion. Fissures and blisters have been observed even in commercial alloys which had been sintered in air, although they are much less severe.' Because of the importance of this sintering treatment it was studied in this investigation in a modified form, using vacuum sintering rather than sintering in air, to insure more complete elimination of occluded hydrogen. The technique is described and the effect of the treatment upon the structure of the alloys is documented. It has been known for some time that extruded aluminum-aluminum oxide alloys are very finegrained, but an exact delineation of grains in electron micrographs has not been possible. In the conventional metallographic-etching techniques etchants attack the interface between the second-phase particles and the matrix in the alloys much

Jan 1, 1964

By Henry A. Stiff, and Lawrence E. Davis

The authors previously presented a method for predicting the tendency of oil field waters to deposit calcium sulfate. The present paper gives a similar method for calcium carbonate. Methods for predicting calcium carbonate scaling tendencies in fresh waters have been available for some time, but these could not be used for brines. By experimentally deriving the value of the K term in the Langelier equation, a method has been developed which applies to waters of high salt content. A statistical study is included which shows that the experimentally derived values of K are in good agreement with actual conditions. Several applications of the final equation to production practice are given. INTRODUCTION The authors previously presented a method for predicting the formation of calcium sulfate scale in oil field waters.' Although calcium sulfate deposition is important in production operations, the majority of scale problems involve calcium carbonate. The present communication discusses a method by which the formation of this type of scale in oil field waters can be predicted. Calcium carbonate precipitation is caused by a shift toward carbonate in the carbonate-bicarbonate-carbon dioxide equilibrium. When equilibrium shifts in the other direction, the precipitate goes back into solution. Since there is usually considerable delay between the establishment of an equilibrium and the precipitation or solution of calcium carbonate, unstable conditions exist in which a water will precipitate or dissolve calcium carbonate on standing. Tillmans? who did a major part of the early work on carbonate scaling, pointed out that the condition of equilibrium not only indicates the tendency of a water to scale but also is an indication of its corrosive properties. Previously precipitated calcium carbonate combines with iron to form a dense crust which inhibits corrosion. If the water tends to dissolve carbonate, the scale becomes porous, and electrolytic corrosion takes place. Tillmans1 work was extended by several investigators until in 1934 Langeliers developed an equation setting forth the conditions of carbonate equilibrium. By the use of this equation the pH of a water at equilibrium can be calculated. If the actual pH is higher than the calculated pH, the water has a tendency to form scale. If it is lower. the water has a tendency to be corrosive. Langelier's equation can be expressed in a simple form as follows: SI = pH-pCa-pA lk-K where: SI is the stability index. A positive index indicates scale formation. A negative index indicates corrosion. pH is the pH of the water sample, as actually determined. pCa is the negative logarithm of the calcium concentration. pAlk is the negative logarithm of the total alkalinity. K is a constant, the value of which depends on the total salt concentration and the temperature. This equation has been shown to apply to waters with totaI solid concentrations as high as 4.000 ppm. In fact, control of fresh water treatment by means of this equation has been standard text-book practice for a number of years. Nomographs have been worked out so that the stability index of a fresh water sample can be determined in a matter of minutes. Most oil field waters, however, contain well over 4,000 ppm of salts and for this reason the usual application of Langelier's equation can not be made. By an empirical method we have extended the application of the Langelier equation to waters of high salt concentration. By the use of this equation the tendency of oil field waters to deposit calcium carbonate can be predicted.

Jan 1, 1952

By Rollin E. Hook, Attwell M. Adair

The yield and fracture behavior of recrystallized chromiztm have been studied in order to gain an understanding of the recrystallization embrittlement-rheotropic recovery phenomenon. The duc tile-brittle tensile transition temperature of recrystallized chromium was found to vary from 225 ° to -80°C as the ratio of specimen diameter/mean planar grain size decreased. The applicability of this observation to other bcc metals is briefly discussed. Brittle fracture in recrystallized chromium was found to be initiated predominately from intercrystalline rupture nuclei. Single crystals exhibit a high degree of ductility at 23 "C. The experimental data indicate that grain boundaries play a significant part in the yield and fracture behavim. Pres training significantly reduces the transition temperature, and high temperature aging does not result in re-embrittle-ment until complete recovery or re crystallization occurs. SEVERAL theories have been used to explain the recrystallization embrittlement-rheotropic recovery phenomenon in chromium. Wain, Henderson, and ohnstone' propose a Cottrell dislocation locking mechanism due to nitrogen, and Weaver and Gross and weaver 3 propose a strain-induced precipitation mechanism involving a chromium nitride precipitate. The researches of many investigators seem to leave little doubt that brittleness in chromium is promoted by interstitial impurities. Smith and seybolt4 have shown that the ductile-brittle transition temperature is lowered as the interstitial content is reduced. weaver3 provides evidence for a 150°C reduction in the tensile transition temperature as the nitrogen content is reduced from 20 to 5 ppm. Maykuth and affee' have suggested that the amount and orientation of grain boundary impurities may be responsible for the brittle nature of recrystallized chromium. This suggestion was based on their findings that wrought iodide chromium possessing a fiberous grain structure is ductile in tension at room temperature while a recrystallized grain structure is completely brittle. Previous investigations have not studied this phenomenon sufficiently to determine its cause. Perhaps this has been largely due to previous experimental findings that brittle fracture observed in chromium has been almost entirely transgranular.' In addition McNeil and imb,' who investigated coarse-grained as-cast chromium, describe the point of initiation of fracture as cleavage, close to the (100) plane, near or at grain bound-daries, or at included particles or voids. However, Hook, Adair, and ipsitt found that fracture in coarse-grained recrystallized chromium is initiated by intergranular rupture and then propagates nearly entirely by cleavage. This result, together with their finding that room temperature ductility in bending is observed for single crystals and coarse-grained polycrystalline specimens for which the number of grains through the specimen diameter is small, suggests that grain boundaries may play an important role in the brittle behavior of chromium. The recrystallization embrittlement problem can be resolved into two questions. These are, whether the controlling mechanism is predominately one of crack initiation or crack propagation, and whether brittle fracture is initiated predominately by slip or twin induced intergranular rupture or by cleavage. The following research was designed to study the role of grain boundaries on the brittle fracture of chromium in an effort to resolve these questions. EXPERIMENTAL PROCEDURES, RESULTS, AND DISCUSSION General Procedure. All tensile specimens (except 0.04 in. diam wires) were prepared from 1/4 in. diam swaged rod fabricated from one ingot. Details of fabrication are given elewhere. The results of impurity analysis for the swaged rod and for the

Jan 1, 1963

By J. W. Matousek, C. S. Samis

me thermodynamic properties of the components in the Cu-Ni-S ternary system have been studied by measuring the H2S/H2 ratios in a gas phase equilibrated with the molten matte at 1200°C. The measured sulficr potentials have been extended by extrapolation and combtned with previously published data to permit the thermodynamic analysis of the ternary system by integration techniques. A simplifying assumption of ideality in the Ni3Sz-CuS pseudobinary has been made. SINCE copper and nickel metals were first extracted from their sulfide ores the interaction between the two metals and sulfur has been of industrial and theoretical interest. The processes developed to extract copper and nickel have been reported periodically in the literature. The theoretical studies on the Cu-Ni-S ternary have been restricted to problems directly associated with production. It is only within recent years that the binary systems related to this ternary have been analyzed thermodynamically and mathematical devices developed to permit a corresponding treatment of the ternary system. In 1910 an investigation of the role of nickel in Cu-Ni-Fe-S mattes was reported,' It was concluded from this work that nickel is not an element replacing iron in mattes, but rather that Cu-Ni alloys behave as a single metal during the matte converting operation. The laws which govern the converting of Cu-Ni alloys were found to be the same laws as those that govern the conventional converting of copper alone. Although considerable information has been reported on the theoretical aspects of copper smelting, little data is available on the smelting of Cu-Ni ores except for phase diagrams and process descriptions. The available information on the Cu-Fe-S ternary and related systems prior to 1953 has been summarized by Ruddle.2 Since Ruddle's publication, Rosenqvist and coworkers have completed phase equilibria investigations of the Fe-S, Co-S, and Ni-S binaries,3 the Fe-S-O ternary,4 and the Cu-Fe-S-O quaternary.4 An extensive investigation of the Cu-Fe-S ternary system at smelting temperatures has been made by Krivsky and Schuhmann.5 At these temperatures, the Cu-Fe-S system is very similar to the Cu-Ni-S ternary with respect to the location of the single-phase and two-phase liquid matte regions. In the former, however, the area of immiscibility is more extensive and the region of liquid matte-liquid metal-solid metal equilibria is much more extensive. Krivsky and Schumann observed that the Cu2S-FeS pseudobinary system is, for practical purposes, an ideal mixture. This investigation has served as a valuable guide in analyzing the Cu-Ni-S ternary. EXPERIMENTAL The experimental procedure employed in this investigation was the conventional technique of equilibration of the sulfide matte with gaseous mixtures of hydrogen and hydrogen sulfide at 1200°C. The thermodynamic properties of sulfur (S2) in the gas phase are determined by means of Eq. [I] and the activity of sulfur in the matte by Eq. [2].

Jan 1, 1963

By J. H. Frye, J. L. Scott, J. W. Woods

THERE are at least two effects of temperature on the stress required to produce plastic flow. 1) Metals plastically strained for the same amount at different temperatures possess different stress-strain curves and different internal structures (e.g., nature and density of imperfections). 2) There is both experimental and theoretical evidence that the stress necessary to produce plastic flow may vary with temperature even though the internal structure remains constant.1-5 Much of the data in the literature is difficult to interpret because these two effects are simultaneously present. In the work reported here, they are considered separately. Standard 0.505 in. tensile specimens were prepared from high-purity Mond nickel and OFHC copper. Nickel specimens were annealed in hydrogen at 1150°C for 30 min and furnace cooled. This produced an average grain diameter of 1.4 mm. Copper specimens were annealed in vacuum at 525°C for 6 hr and furnace cooled. This produced an average grain diameter of 0.11 mm. Nickel tensile specimens were prestrained in tension at 500°K, whereas copper tensile specimens were prestrained in tension at room temperature. All specimens were cooled to 74°K and heated to room temperature. After these treatments all of the tensile specimens of a given set possessed identical structures. All specimens were returned to the tensile machine and tested at various temperatures and constant cross-head speed. Many of the tensile curves showed well defined yields but, in order to minimize personal judgment, the yield was always chosen as the stress corresponding to 0.2 pct plastic deformation. Results are summarized in the graph of yield vs temperature of test, Fig. 1. All of the specimens corresponding to any one line have had identical treatments and, therefore, have identical internal structures. Thus, each line gives the relation between yield stress and temperature for one constant internal structure. The lowest line, which is for annealed nickel, shows no measurable variation of yield with temperature. This is similar to Blewitt's6 results on copper single crystals, but a variation in yield with temperature was found by Andrade and Henderson' in single crystals of nickel, and by Car-recker and Hibbard8 in annealed polycrystalline copper. The three other lines, which are for prestrained materials, show that there is a linear relation between yield stress and temperature when the internal structure remains constant. Such a relation might be expected from a rate equation such as that of Kauzmannl on the assump- tion that the activation energy is either independent of or linear with temperature. These results would also be expected if the shear moduli of copper and nickel are linear functions of temperature for, as Cottrell and Stokes have pointed out," in all dislocation theories of strength the flow stress appears proportional to the shear modulus of the material. In copper and nickel, since the modulus of elasticity decreases roughly linearly with increase in temperature," it is probable that the modulus of shear also decreases approximately linearly with increasing temperature. A detailed discussion of the effect of these and other factors on the temperature dependence of flow stress in face-centered-cubic metals has recently been given by Seeger.4

Jan 1, 1958

By R. C. Rumble

To /neet the need for a subsurface flowmeter capable of measuring low rates of flow, a new type flowmeter has been built and tested in the field. This instrument is self-contairzed, can be run on a wire measuritzg line, and may be run through 2-in tubing. It consists of a rotameter flow-measuring assembly used in conjuncfion with a conventional subsurface instrument clock and chart. Integral with the tool is an inflatable packer which, by effecting a seal between casing and tool, diverts all fluid through the metering assembly. Packers of different size adapt the tool to different sizes of casing or liner. The flowmeter is capable of measuring rates of flow as low as 4 BID. The flowmeter has been run experimentally in seven wells. It has yielded satisfactory resrrlts in five of the wells, and in the other two it failed to operate because of loose sand in the hole. INTRODUCTION One of the oldest problems facing the producing branch of the petroleum industry is the location of depths of entry of fluid into a wellbore and the determination of the amount of fluid entering at each depth. This problem is often encountered in oil and gas wells completed in single producing horizons as well as in multiple pays; it is a common problem in oil wells which produce excessive volumes of gas. Several subsurface instruments designed to detect and meter flow in the producing interval of wells have been described in the literature.1,2,3,4 Most of these, however, were apparently intended for use in wells producing at relatively high rates of flow, and consequently lack sensitivity to low flow rates. Because of this and of other possible disadvantages inherent in these instruments, development of the subsurface flowmeter described in this report was undertaken. DESIGN OF FLOWME'I'ER Design Requirements In considering the requirements for a flowmeter that would not be subject to the limitations of devices existing at the time work was started, attention was first given to the size of the tool. Such an instrument should be of sufficiently small diameter that it could be lowered readily in 2-in tubing in a producing well. The flowmeter should contain a recording unit so that it might be run on a wire measuring line with conventional reeling equipment. It should not be too long to be accommodated by a portable lubricator of the type used for running conventional subsurface instruments. The metering mechanism of the flowmeter should not be affected appreciably by the viscosity or density of the flowing fluid. Such an instrument should record flow rates in the range from less than 10 B/D to over 100 B/D. To achieve this, a packer should he provided to divert through the instrument all fluid flow in the wellbore. This packer should be of such nature that in the event of excessive flow the fluid would bypass the instrument instead of forcing it up the wellhore. General Description A flowmeter incorporating most of the desired features outlined above was developed and built. The instrument is an elongated tubular device terminated on

Jan 1, 1956

By Tom Westgarth

As papers are placed before you upon large gas-engines in Belgium and Germany, it was considered that some information should be given upon the same subject in Great Britain. I therefore agreed to compile these notes, which I have made very short in view of the somewhat full nature of the other papers presented to this meeting, and considering the complete nature of the many publications which have been made recently upon the subject of large gas-engines. I give below Tables I. to VI., showing the number and particulars of large gas-engines which have been built or are building by British makers, and in view of the growing size of gas-engines I have concluded that engines of less than 500 h.p. cannot now he included in the category of large gas-engines, and therefore I have not considered engines under that power. Table I.—-" Oechelhauser " Type Gas-Engines. Built or Building by William Beardmore Co., Limited, Glasgow Indicated ! Engines. Horse-Power Type. Nature of Work. Gas Used. 6 2,500 Twin cylinder. Dynamo. Producer. 1 in Single cylinder. Rolling-mill. Producer. 4 1,250 Twin cylinder. Dynamo. Producer. 2 1,250 Single cylinder. Dynamo. Producer. 4 625 Single cylinder. Dynamo. Producer. 1 625 Single cylinder. Rolling-mill. Producer. 1 625 Single cylinder. Air compressor. Producer. 2 500 Single cylinder. Air compressor. Producer. 7 500 Single cylinder. Cement-mill driving Producer. Total, 28 engines ; 32,600 indicated horse-power. * Presented at the Joint Meeting of the Iron and Steel Institute and the American Institute of Mining Engineers, London, July, 1906, and here published under a mutual agreement between the Councils of the two Institutes.

Jan 1, 1907

By John L. Schroder

In selecting the best system of mining for a particular operation, many different factors must be considered. The system to be finally selected should be that which provides: 1) The highest possible degree of safety for mine personnel. 2) The lowest cost per ton of product. 3) The maximum coal production per man-shift. 4) The most suitable quality of final product, considering its intended use. 5) The maximum percent recovery of coal per acre of reserve consistent with cost and subsidence rights. 6) Consideration for the ecology of the area. Some of the important factors to be considered when choosing a method of mining are: 1) Amount of cover over the coal seam. 2) Type of the rock in the overburden. 3) Characteristics of the coal seam including: (a) the thickness of the coal seam; (b) the nature and location of any impurities or irregularities; (e) the dip (or pitch) of the coal seam; (d) the nature and direction of any definite cleavage ill the czoa1 seam; (e) the hardness of the coal; (f) the structural strength of the coal; and (g) the presence, anti amount, of explosive gas (methane). 4) Quantity of water likely to be encountered in the mining operation. 5) Nature and strength of the roof (top) over the coal seam. 6) Nature and strength of the floor (bottom) under the coal seam. 7) Any previous or concurrent mining in seams above or below the coal seam to be worked. Information on items 1-7 may be obtained in several ways. Topographical and geological reports and maps of the area are generally available

Jan 1, 1973

By F. R. Wadleigh

There are in commercial use today in the United States various classifications of coal, each based on one or more characteristics. The bases of these classifications may be described as follows: GeNeRaL Basis Examples 1. Geological By seams and basins (local). 2. Chemical By constituents, as determined by analysis—ash, volatilc, slilfur and hcating value. 3. Combustion Characteristics As frce-burning, smokeless, character of ash. 4. Carbonization Characteristics Coking, noncoking. 5. Physical Characteristics Splint, soft, hard, block. 6. Geographical States, Fields, Counties, Districts. 7. Sizes By dimension or name. 8. Company Names Producing or sales company names, as "C. C. B. Pocahontas," etc. 9. Trade Names, copyrighted or not 10. Uses Gas, steam, coking, locomotive, fuel, bunkers, etc. 11. Use Methods Stoker coal. 12. Pools (Tidewater Exchanges) Analyses Size Seams Railroads Uses Structure Districts There are also classifications founded on more than one basis, as follows: 1. Geographical and Geological. By locality of mines (State, District, County) and seam. Examples: Cambria County, Miller Seam, New River, Sewell Seam. 2. Geographical and Chemical. Alabama medium volatile. 3. Combustion Characteristics and Ash Content. Free-burning, red ash (anthra- cite). 4. Carbonization Characteristics and Analysis. Noncoking, high-volatile, low sulfur. 5. Physical and Carbonization Characteristics. Splint, noncoking. 6. Size and Use. ¾-in. gas coal; domestic sizes (prepared sizcs); stcam sizcs. 7. Company Name and Seam. Consolidation Co., Elkhorn. 8. Size and Analysis. Low-volatile run-of-mine; low-volatilc slack. 9. Sizes—size of screen and name. 6 by sin. lump. 10. Chemical and USP. High-volatile steam. 11. Geographical and Use. Youghiogheny gas. 12. District, Size and Use. Pittsburgh gas l¼-in. lump. ,

Jan 1, 1930

By Harrison Schmitt

DURING the past decade the writer has studied and mapped certain ore deposits and their structural associations in the states of Chihuahua, Durango, New Mexico and Arizona, and he believes that these deposits, with the exception of the manto-chimney, are representative of the principal types in the area of the states named. In this paper the deposits are described; then generalizations are drawn so far as seems appropriate. HANOVER, NEW MEXICO The Hanover; New Mexico, zinc deposits were briefly described by Lindgren and others,1 Paige2 and recently in more detail by Schmitt.3 These, the kind ordinarily called contact metamorphic, border the southern end of an oval area of granodiorite intrusive 3/4 mile wide and 2 1/2 miles long (Fig. 1). The granodiorite has intruded, folded, and metamorphosed sedimentary and igneous rocks, which range in age from pre-Cambrian to Upper Cretaceous. About 90 per cent of the ore has replaced coarse, recrystallized, pure, fossiliferous, lower Mississippian, nonmagnesian limestone (Hanover limestone) 110 ft. thick;4 about 75 per cent of it occurs in the upper 50 ft. of this horizon just below an 18-ft. lower Pennsylvanian shale bed, which lies on a locally inconspicuous unconformity representing upper Mississippian time. The orebodies show five shapes or attitudes, each dependent on a special structural situation: 1. Most of the ore occurs as podlike; thick lenslike or other "three-dimensional" shoots extending from top to bottom of the Hanover limestone and lying adjacent to the outer contact of a silicate zone largely of andradite, which follows the intrusive contact (Figs. 1 and 2).

Jan 1, 1933

By J. H. Bowden

The shaft-plant here described was put in operation in September, 1895, and the No. 6 slope-motor was started in May, 1896. The plant comprises : One Norwalk three-stage compressor l21/2, 91/2 and 5 in. diameters of air- and 20 in. diameter of steam-cylinder, all 24 in. stroke; capacity at 100 revolutions, 296 cu. ft. of free air per minute, compressed to 600 Ibs. per sq. in. A main pipe, 5 in. diameter, 4380 ft. long, with five charging-stations in No. 6 Shaft, and a branch of 3 in. pipe, 3100 ft. long, with three charging stations, in No. 6 Slope. These pipes on each line charge a Porter compressed-air motor, with 7 by 14 in. cylinders, and four 24 in. drivers, weighing about eight tons, with a tank-capacity of 130 cu. ft. of air at 550 lbs. pressure in the main tank, reduced to 160 lbs. in the 8-in. auxiliary tank of 4.2 cu. ft. capacity, supplying the cylinders. The No. 6 shaft run averages 4000 ft. each way on grades of $ to 23/4 per cent., and averaging close to one per cent. in favor of the loaded cars. The No. 6 slope run averages 2100 ft. with nearly the same grades. The mine-cars weigh 2800 Ibs. empty, and about 9800 lbs. loaded, and are hauled in trips of 12 to 20, averaging about 15 cars. The shaft-motor now hauls about 355, and the slope-motor 320 cars per day of 10 hours, replacing in the shaft 17 mules, and

Jan 1, 1901

Committee on Reduction and Refining of Copper............ 3 A.I.M.E. Officers and Directors.................... 4 Preface. By C. R. Kuzell....................... 7 Career and Achievements of James Douglas. By Arthur L. Walker. . 9 PAPERS Smelting 1. Reverberatory Smelting Practice History of Reverberatory Smelting in Montana, 1879-1933. By Frederick Laist..............................23 Reverberatory Smelting of Raw Concentrates at the International Smelter, Miami, Arizona. By P. D. I. Honeyman (With Discussion)...... 88 Development of Gun-feed Reverberatory Furnaces at Garfield Plant of American Smelting and Refining Company. By R. A. Wagstaff (With Discussion)........................99 An Experimental Combination of Shaft Roasting and Reverberatory Smelting. By Frederick Laist and J. P. Cooper (With Discussion).... 104 Forms of Copper Found in Reverberatory Slags. By Royal B. Jackman and Carle R. Hayward (With Discussion).............111 2. Converting Practice Development of Copper Converting at Butte and Anaconda. By William Kelly and Frederick Laist...................122 Developments in Converting Lead and Copper Matte at Tooele. By B. L. Sackett.............................132 Messina Stationary Basic Copper Converter. By R. G. Knickerbocker (With Discussion)........................140 Smelting Copper Concentrates in a Converter. By George E. Beavers. 149 Sulfuric Acid from Converter Gases. By George E. Beavers......151 Development of Monolithic Tamped Periclase Converter Linings at United Verde Copper Company Smelter. By F. H. Parsons (With Discussion) . 153 3. Descriptions of Plants The Noranda Smelter. By W. B. Boggs and J. N. Anderson......165 Smelting Operations at Roan Antelope Copper Mines, Limited. By Charles R. Wraith.......................202 4. Waste-heat Boiler Practice Copper-refinery Waste-heat Boilers at Great Falls Reduction Department, Anaconda Copper Mining Company. By E. S. Bardwell......225

Jan 1, 1934

By E. J. Schmitz

This section was obtained last year during an examination of the iron-ore resources of the Rich Patch Mountain region and along Craig's creek valley. The geological members below the Oriskany and Lower Helderberg are exposed along the gap in a beautiful arch, while the higher formations appear in a more or less disturbed state on both sides of this arch, and are partly covered by dèbris. I have thought it of interest to the Institute to reproduce the drawing of this section at the gap which I made in my note-book at the time of my examination; those parts of the section, which lie at both sides of the arch, are only approximated. I give also a number of notes and measurements, referring to the Clinton formation and especially to the characteristics of the fossiliferous ore-seam opened in the various tunnels along the arch (see section). I. In Tunnel C: For the first 110 to 120 feet to second shute, we find the ore only here and there in small deposits, and interchanging with, or changing into, either a very siliceous limestone or a sandstone. About 10 feet beyond shute we have : Sandstone roof. Clay-slate, 211/2 inches Brown lean ore, 1 inch. Sandy clay, 3 to 31/4 inches. 1. Dark .brown ore, 3 inches. 2. Fossil-ore, changing into sandstone or very siliceous limestone, 2 inches. 3. Brown lean ore, 6 inches. Clay and slate below, 1 foot. 194 feet from entrance : Sandstone roof. Clay-slate, 4 inches. Clay 15 inches. Fossil-ore, 63 to 7 inches. Clay and ore, If inches. Lean brown ore, 2 inchea. Clay to bottom, 2 feet.

Jan 1, 1896

By W. L. Phillips

Stress-strain curves were obtained for single crystals of 70 pct Ag-30 pct Zn tested in tension and shear. Samples tested in tension and shear had comparable resolved shear stresses and stress-strain curves. The {111} <110> slip system was observed. It zoas found that the9.e is a barrier to slip in both latent close -packed directions and that the magnitude of these barriers is proportional to prior strain during easy glide. It was observed that cross-slip in tension and shear was most frequent in crystals with an initial orientation near <100> "Oershoot" zoas observed in tension. The amount of this "overshoot" was independent of initial orientation. AN idealized concept of plastic deformation indicates that a single crystal should yield at some stress that is dependent on crystal perfection and it should then continue to deform plastically by the process of easy glide which is characterized by a linear stress-strain curve and a low coefficient, d/dy, of work hardening. Hexagonal metal crystals generally conform to this ideal concept of laminar flow. In fcc metals the range of easy glide is always restricted in magnitude and it is strongly dependent on orientation, composition, crystal size, shape, surface preparation, and temperature. Since one of the principal differences between the two crystal systems, both of which deform by slip on close packed planes, is the existence of latent slip planes in the fcc crystals, it has been proposed that the transition from easy glide to turbulent flow, characterized by rapid linear hardening, is due to slip on secondary planes intersecting the primary plane.ls Several theories have been proposed to explain the linear hardening and parabolic stages of the stress -strain curve.6"10 The easy-glide region is the least understood of the three stages. The stress-strain characteristics of Cu-Zn, which shows a long easy-glide region, have been extensively investigated."-" In light of recent ideas on dislocations, cross-slip, effect of solute atoms, and stacking fault energy, it was felt that the certain features of this earlier work might be compared with another alloy, Ag-30 pct Zn, which also exhibits a long easy-glide region. Tension and shear stress at room temperatures were employed. The results obtained, together with some interpretation of the observations, are described below. EXPERIMENTAL PROCEDURE The silver and zinc used for mixing the alloys were 99.99 pct pure. The two components were weighed to within 0.1 pct of the weights required fo the alloy composition. They were then placed in a closed graphite mold and the mold and contents were heated in 100°C stages from 500&apos; to 900°C with sufficient time and vigorous agitation at each stage provided to dissolve the silver. The crucible was then heated to 1150°C and agitated violently before being quenched in oil. The resulting alloy rod was machined free of sur face defects and then placed in a graphite mold designed for growing single crystals. The graphite mold was closed with a graphite plug and was encased in a pyrex glass tube which was connected to a vacuum system. The tube and mold assembly were placed in a furnace; the tube was evacuated and the furnace was rapidly heated to a temperature sufficient for fusing and sealing the glass. The glass-encased evacuated mold and contents were then lowered through a vertical furnace. The top section of the furnace was held at 100 °C above the melting point of the alloy. The lowering rate was 1.5 in. per hr. The tension specimens were 1/4 in. diam; the shear specimens were 1/2 in. diam. These specimens were then removed from the mold, etched, and chemically polished with hot (60°C) Chase etch reagent (Crz03-4.0 g, NH4C1-7.5 g, NHOs-150 cc, HzS04-52 cc, and Hz0 to make 1 liter). In preparation for tensile testing, the specimens were carefully machined to a diameter of about 0.200 in. to permit a gage length of 6 in., annealed for 16 hr at 800&apos; to reduce coring, and then cleaned and polished. A modified Bausch-type shear apparatus which has been described previously18 were employed. The gage length was 1/8 in. This shear apparatus was placed in an Instron tensile testing machine. EXPERIMENTAL RESULTS A) Tension. Several specimens were extended at room temperature to determine the effect of initial orientation on the stress-strain curves of Ag-30 pct Zn. The initial orientation and the resolved shear stress supported by the active slip system at various total strains are plotted in Fig. 1. The critical resolved shear stress, t,, initial rate of work hardening, d/dy, and length of the easy-glide region are independent of orientation. The arrival at the symmetry line is shown by an arrow in Fig. 1. During the easy-glide region of the stress-strain

Jan 1, 1963

By Ziebell, Howard A.

THE Washington magnesite deposits, located in the hilly and mountainous northeastern part of Washington, occur as massive lenses in a sedimentary series made up of dolomite, shale, and quartzite, into which basic dikes have intruded. The ore pattern resembles a series of disconnected chain links extending approximately 25 miles in a south-west direction. Magnesite in this district is all crystalline and closely associated with dolomite, talc, serpentine, and basic dike rock. All deposits which have been developed are near the surface so that quarry-bench mining has been possible. For over twenty years hand sorting magnesite ore at the quarry face was standard practice. Ore cars were hand trammed on 30-lb rail systems which led from the face to ore passes or raises for the magnesite ore and to the waste dumps for disposal of the rejected waste material. This system was somewhat modified by the use of Dempster Dumpster trucks. The ore was, however, still sorted by hand from the calcium and silica bearing waste rock. Power equipment. consisting of one 3/4-yd electric shovel, was

Jan 1, 1949

"Located at Canyon Ferry on the Missouri River, 17 miles from Helena and 63 miles from Butte. River drainage area 15,570 sq. miles. Built in 1898.DAM: Rock-filled, wooden crib, 490' long and 39' feet at maximum head; also masonry core, earth bulk-head 300' long and granite masonry abutments.SPILLWAY: 473' long, crest elevation 3660.5; steel flashboard system 10' high.PENSTOCKS: 10 main penstocks, 12' diam., about 40' long, leading from canal to turbines, each supplying 1 pair turbines.WHEELS: 4 main center discharge, horizontal units, each 1 pr. of 42"" wheels made by Dayton Globe Iron Works, and 6 main units, each 1 pr. of 45"" wheels made by S. Morgan Smith Co., all 157 r. p. m., normal head 34', and direct coupled to generators.GENERATORS: 10 W. E. & M. Co., Kodak Type, revolving armature, 750 k-w., 157 r. p. m., 550 v., 3 phase, 60 cycle alternators.OPERATION: The plant has large water storage and can carry peak loads to 12,000 h-p. It is the central control station for the system."

Jan 1, 1913

By John C. McDonald

CONTROLLED cold work is used between solution heat treatment and precipitation heat treatment for producing certain tempers of the commercial aluminum base alloy 2219 (designation of the Aluminum Association, U.S.A.) which contains 6.3 pet Cu as the major ingredient responsible for the age hardening. The complete composition limits for this alloy are listed in Table I. The alloy has been described in detail,&apos; and the control of the heat treatment has also been published.2 Beneficial effects of such cold work in other alloys have also been pointed out.3&apos;4 NO data have been published on the effects of varying amounts of cold work under fixed aging conditions. In connection with an investigation of the possibility of providing the desired cold work by explosively generated shock waves, it became desirable to investigate the effect of variable cold work, and to compare the re -sults with those obtained from explosives. The general principles of explosive hardening are well-described in the literature.&apos; All material used was guaranteed by the supplier

Jan 1, 1968

By Jack C. Jones, Hemendra N. Kalia

This paper is partially based on a comprehensive ground control investigation that was conducted by Harza Engineering Company under a contract from the Bureau of Mines. This investigation required in- stalling several types of ground movement indicating devices on the surface and in the mine. The major instrumentation systems consisted of hydraulic borehole pressure cells, multi-point extensometers, in- clinometers, convergence indicators, Jack pressure recorders time domain reflectometers, and a 200 station subsidence network. The investigation demonstrated the versatility of the system. We were able to install pressure cell s to a depth of over 200 feet in the coal bed and we were successful in installing 10 pen mechanical recorders to monitor differential strata movement. In this paper, we have briefly discussed data from 18 borehole pres- sure cells, two time domain reflectometer cables and four subsidence lines. The data collected showed that the front and rear abutment pressures were approximate1 y 1000 feet (304.81~1) to 1200 feet (356.76111) from the active face. The peak pressure was about 4 times the over- burden pressure.

Jan 1, 1983

By J. H. Brophy, A. I. Prill

The authors have previously investigated the solid-state activated sintering of tungsten powder with various Ni-Cu additions.&apos; Log shrinkage vs log time plots showed changes in slope from 4 to x at intermediate times during the sintering process. This was attributed to a change in the rate-controlling mass-transport process from solution of tungsten into the tungsten-alloy interface to diffusion of tungsten in this interface. It was postulated that the melting of the activating layer should not affect this transport process. However, the superposition of rearrangement due to the presence of a liquid phase complicates the data analysis. It is the purpose of this note to apply the analysis of Prill, Hayden, and rohy&apos; to account for "rearrangement shrinkage&apos;? in liquid-phase sintering of the W-Ni-Cu system. This results in "solution-precipitation stage" shrinkage plots which were comparable to those obtained in solid-phase activated sintering of the same system. If one assumes total shrinkage to be the sum of rearrangement and solution precipitation, the effects can be isolated easily.2 This results in the general equation:

Jan 1, 1967

By Frank C. Roe

Two cogent and ubiquitous facts have supported a constant search by the ore processing industry for better wear resistant materials in equipment. First, designs and types of equipment change or improve continually to meet the economic and physical demands of different and/or leaner ores. Second, practically all equipment is subject to impact and abrasion conditions that probably are more severe and extensive than in any other industry. Development and testing by operators and equipment manufacturers alike, has produced an extensive variety of longer lasting metal alloys, rubber, plastics, ceramics and other materials to improve equipment performance under different specific conditions. The need for diversified materials becomes obvious upon the simple realization that no two beneficiation operations are identical. Among the variables in the handling of ore are: 1. Size and weight of ore particles. 2. Hardness and sharpness of ore particles. 3. Concentration of ore particles in liquid or gas suspension. 4. Velocity and direction of particle impact toward equipment surface. 5. Coefficient of friction between ore particles and equipment surface. 6. Temperature of operation. 7. Chemical environment of operation.

Jan 12, 1967