Search Documents

By R. P. Smith

Iron-carbon alloys containing a single-phase austenite region and a two-phase azcstenite + cementite region at the desired temperature were prepared by partial carburization of iron or partial decarburization of carburized iron. Each sample was held at a fixed temperature until equilibrium was achieved. Analysis of the austenite for carbon then gave the solubility of cementite in austenite. Solubility measzcrements were made for the temperature range 734° to 1012°C. These values together with other data give 7560 cal for the mean heat of solution of cementite in austenite, and 0.765 pct C for the eutectoid composition of austenite. They also indicate that graphite is the stable phase at all temperatures between the eutectoid and eutectic temperature. Measurements of the solubility of cementite in austenite at 927oand 1011 "C, using a method based on the equilibration of iron with boro-cementites, are reported. The solubility of cementite in austenite (?-iron) has been computed by Darken and Gurry1 from the observed solubility of graphite in austenite, and the thermodynamic properties of pure iron and of iron-carbon alloys. They have shown that the solubility of cementite is greater than that of graphite in the temperature range between the eutectoid and eutectic, and thus that cementite is metastable with respect to graphite and austenite saturated therewith. Since their computation is not in accord with the earlier experimental work of Mehl and wells,' the present direct determination of the solubility of cementite in austenite was undertaken. EXPERIMENTAL PROCEDURE Each iron rod about 1/2 in. O.D. by 4 in. was first carburized at a temperature and with a H2-CH4 gas mixture such that the carbon content would be greater than that corresponding to the solubility of cementite in austenite at the desired (lower) temperature; sufficient carburizing time was allowed that the carbon content became substantially uniform, as illustrated by Curve A, Fig. 1. The sample was then partially decarburized with a hydrogen-water vapor mixture, giving a carbon distribution as schematically illustrated by Curve B. The sample was then held in a helium atmosphere at the temperature at which the solubility was to be determined until the decarburized portion of the sample came to equilibrium with that containing cementite. Curve C of Fig. 1 represents schematically the final carbon distribution; the horizontal portion corresponds to the carbon content of austenite saturated with cementite. To bring the sample to room temperature without change in the carbon distribution and in machinable condition, it was first quenched in a salt pot at 480°C, then in water at room temperature. Successive layers were machined from the center 2 in. of the sample and analyzed for carbon by the usual

Jan 1, 1960

By P. M. Robinson, M. B. Beaer

The heat of formation at 0°C of the intermetallic compound AgMg as a function of composition has been determined by tin-solution calorimetry. In this technique, the heat of formation is determined as the difference in the heat effects, at infinite dilution, on dissolution of the compound and a mixture of its components added alternately to liquid tin from a reference temperature, such as 0°C. The experimental technique and method of calculation have been described elsewhere.' The compound AgMg is a 0 electron compound with a CsCl structure.2 In nonstoichiometric compositions of the compound, atoms of the excess component are substituted on the AgMg lattice.3,4 The homogeneity range is approximately 43 to 52 at. pct Mg at room temperature and 38 to 65 at. pct Mg at 500Oc.2 Single-phase alloys outside the homogeneity range at room temperature can be prepared by quenching. The specimens used in this investigation contained from 39.0 to 54.8 at. pct Mg. They were made available, together with analyses, by the Research Laboratory of the General Electric Co. Metallographic examination of the quenched specimens containing 39.0 and 54.8 at. pct Mg gave no indication of the presence of a precipitated phase. The measured heats of formation are listed in Table I. In a calorimetric run, four to six additions each of a specimen and the corresponding mixture of the components were made. One or two calorimetric runs were carried out with each composition depending on the amount of samples available. The limits stated in the table represent the experimental precision and not the absolute accuracy of the measurements. Thermodynamic investigations of the compound AgMg have been made by Trzebiatowski and Terpilowski 5 and Kachi.6,7 The heats of formation at 500°C derived from the combined electromotive-force values of these investigators8 are more exothermic than the heats of formation at 0°C reported here, Fig. 1. The differences cannot be explained by the difference in temperature. This is shown by the published heat capacity of the stoichiometric compound, which obeys the Kopp-Neumann rule from 0" to 500oC.9 The heats of formation derived from equilibrium data are generally considered to be less accurate than those determined by calorimetric methods because small errors in the change of the equilibrium values with temperature have a large effect on the calculated value of the heat of formation. The heats of formation derived from the combined published electromotive-force values reach a maximum at 56.0 at. pct Mg.8 Kachi reports a maximum of -4.7 kcal per g-atom at the stoichiometric composition.7 The present results also indicate a maximum at or near the stoichio metric composition, Fig. 1.

Jan 1, 1964

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By N. P. Peterson

The Castle Dome copper deposit is of the porphyry type and occurs in a body of quartz monzonite intruded into the pre-Cambrian formations and possibly into the lower part of Paleozoic limestones. The hypogene sulphide minerals include pyrite, chalcopyrite, and a little molybdenite, sphalerite, and galena. Pyrite and chalcopyrite are disseminated or occur in small closely spaced veins. The hypogene mineralization shows distinct zoning in the distribution of pyrite and chalcopyrite, so that the mineralized area can be subdivided into pyritc and chalcopyrite zones. Supergene enrichment, though not extensive, played an important part in the formation of the ore body, the chalcopyritc zone being the pro-tore. Several thin, gently dipping, diabase sills occur in the mineralized area, and the copper content of the rock in and near these sills is substantially higher than average. The formation of the ore body was caused by the combined effects of three forces: I. Zoning of the hypogene mineralization, 2. Richer copper metallization associated with the diabase sills, and 3. Supergene enrichment. Introduction The Castle Dome copper deposit is about 5 miles west of Miami, Arizona, and about 3 miles west of the Miami-Inspiration ore body. The Castle Dome open-pit mine is on the south flank of Porphyry Mountain, a prominent landmark of the region. In 1941 the deposit was being explored by the Miami Copper Co., but the exploration program was cut short when the decision was made to develop the property as a war project. The Castle Dome Copper Co., Inc., was organized as a wholly owned subsidiary of the Miami Copper Co., and arrangements were made with Defense Plant Corp. for developing and equipping the mine and for construction of a concentrating plant. Construction and development work was begun in January 1942, and milling operations started June so, 1943. Since that date, the mine has been in continuous operation by the Castle Dome Copper Co, under a lease agreement with Defense Plant Corp. producing copper at an average rate of 4,000,000 lb per month. To January I, 1946 the total production amounted to 121,088,000 lb of copper,4,271 oz of gold, and 211,755 oz of silver. A detailed study of the copper deposit and the surrounding area was undertaken by the U. S. Geological Survey in June 1943. Other members of the Survey participating in the work were C. M. Gilbert, G. L. Quick, and J. P. Albers. The results of this work will be published as a comprehensive report by the Geological Survey. General Geology The Globe quadrangle, which includes the Castle Dome area, was studied by F. L. Ransome1 of the Geological Survey in 1901 and 1902. His maps and descriptions were

Jan 1, 1949

By Jack A. Kanz, Samuel R. Shortes, E. C. Wurst

Zinc diffusion into GaAs from the vapor phase through reactively sputtered SiO, films Izas been inrestigated for various zinc pressures at 1000"C. Diffusions were carried out in evacuated quartz ampules with elemental zinc and with various Zn-Ga alloys. Sputtered films have proved effective in lowering surface concentrations and preventing surface deterioration during diffusion. Approxin.ate complenzentary error-function impurity distributions were found when surface concentrations were reduced to approximately 3 -—4 x 10" atoms cm'3 or less with dilute zinc sources or by diffusion through SiO, films. Zinc difhsions in GaAs tlzrough SiO, films produced more planar diffusion fronts than were observed with uncoated zuafers under identical conditions. A) Surface Deterioration During Diffusion. Device technolorn-- in compound semiconductors has been hampered by several difficult problems not normally encountered with silicon and germanium. 111-V and 11-VI compound semiconductors generally have volatile constituents at temperatures used for diffusion. To achieve specific junction depths in reasonable lengths of time, or to obtain particular impurity distributions and doping levels, it is often necessary to use temperatures which cause surface deterioration and erosion of the wafer. The resultant surfaces are generally unsuitable for devices. The type and extent of surface damage depends to varying degrees on the particular environment of diffusion and on the particular impurity in question. The most common type of deterioration results from simple dissociation of the gallium and the arsenic during diffusin.' The deterioration process is significantly enhanced by thermal gradients in the diffusion zone, usually resulting in vapor transport and condensation at the cooler portion of the system. The resulting damage sometimes appears as a general haziness over the surface or an array of pyramidal etch pits characteristic of the particular orientation. Occasionally, erosion of the surface occurs uniformly over the wafer so that surface loss is not readily apparent. Workers in GaAs usually resort to the sealed-ampule type of diffusion system3"5 rather than the more conventional open system used for silicon and germanium. Another type of deterioration results from direct interaction of the impurity with the surface. The form of deterioration may vary from surface alloying, as in the case of zinc, to direct chemical attack and vapor transport of the reaction products, as in the case of sulfur. Surface alloying with zinc occurs at higher temperatures and source vapor pressures.4 The process is largely controlled by the amount of free gallium on the surface of the wafer in equilibrium with the arsenic lost to the system. The group-VI elements, sulfur, selenium, and tellurium, are commonly used donor impurities for gallium arsenide. These elements are characterized by high vapor pressures and high chemical

Jan 1, 1964

By H. J. Modi, P. L. De Bruyn

IN recent years interest has been aroused in flotation rate studies both from a technical and a more practical aspect. With increasing fineness of grind becoming a necessity in treatment of low grade ores, difference:; in flotation rates of various size ranges will assume importance in the evaluation of overall recovery results. Theoretical analysis of flotation kinetics was initiated by Schuhmann,' who sought to define flotation rate of a given mineral and specified size range in terms of certain physical variables of the flotation system. Using as a basis for his analysis the bubble-particle encounter hypothesis previously advanced by Gaudin,' Schuhmann writes for the rate of flotation (R,.) of particles of average size x, Rx = PcPa(x) V F. [1] In this relation Pc and Pa represent, respectively, the probability of collision between particle and gas bubble in a given time interval and the probability of adhesion of particle to the bubble after collision. Rigorously speaking, the term PC does not have the significance of a probability factor, since it depends on the time interval and therefore can be numerically greater than unity. The term c(x) expresses the concentration of particles of an average size x in the flotation cell in weight per unit volume of pulp, and V denotes the total volume of pulp in the cell. The product, P,c(x)V, defines the frequency of particle-bubble collisl.on, and when it is multiplied by P,, the number of collisions per unit time resulting in successful adherence is obtained. The factor, F, measures the froth stability and is introduced because after fruitful bubble-particle contact some particles may still riot reach the froth launder. Coalescence of bubbles in the froth column or too short a bubble life could account for this effect. Schuhmann also introduced the concept of "specific flotation rate" (Q) to allow for the relative abundance of different mineral species in the flotation pulp. The specific flotation rate, having the dimension of reciprocal time, is defined as Eq. 2: Qx =Rx/c(x)v [2] and it also follows from Eq. 1 that Qx = PcPaF. [31 The theoretical aspects of flotation kinetics were also considered by Sutherland,3 who tried to improve Eq. 1 by expressing the probability factors in terms of such physical variables as particle radius (x), bubble radius (X), velocity of bubble relative to particle (v), the number of bubbles per unit volume of pulp (N) and the induction period (A) necessary for air-mineral adhesion. According to Sutherland's treatment, the rate equation, Eq. 1, transforms to R, = [3pX x v N] [sech2 (3 v ?/4 X) ] ?c(x) V [4] where the first term in brackets on the right-hand

Jan 1, 1957

By Shiou-Chuan Sun

There are several postulations for the mechanism of slime-coating. Incel proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube. after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4:I and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,' several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.4a per liter of water, should not be

Jan 1, 1943

By Shiou-Chuan Sun

There are several postulations for the mechanism of slime-coating. Incel proposed the electrostatic hypothesis, del Giudice2 suggested the chemical theory; Bankoff3 reported that slime-coating is inhibited whenever the surfaces of the slime particles are ionized sufficiently for Brownian movement to occur, and is facilitated when they are not. These postulations were examined by experiments involving the Burton tube, the cataphoretic cell, and slime-coating. The techniques involved will be described elsewhere in this paper. The electrostatic hypothesis, supported by migration experiments in a Burton tube, was abandoned by del Giudice.2 Experiments of mineral migration in a Burton tube. after the idea of Ince with modification, indicated that this apparatus was inefficient for accurate observation. A cataphoretic cell was constructed. The experimental data, as shown in this paper, enable the correlation and advancing of this hypothesis. Del Giudice's chemical hypothesis considered that slime particles are attached to the galena surfaces by a cement formed as the result of a metathetical reaction between the sulphide and the slime particles. Applying this hypothesis, the calcite slime particles were cemented to the galena surface by the formation of a cementing lead carbonate. In a similar way, lead silicate was considered as the cement of quartz slime coating on galena. Experiments verifying this hypothesis were carried out according to the following procedure: Fresh mineral particles selected from the central part of the broken lumps and examined first under a microscope for ascertaining a clean surface were placed in a small beaker (1.5-in. dia. by 2.5 in. deep) half filled with one kind of slime pulp. The dilution of all slime pulp was 4:I and the particle size of slime was minus 400-mesh. After agitation for 5 min. the specimen was removed by a sharp-end tong and washed gently three times in three separate distilled water baths. It was dried before a small electrical fan and examined immediately under a microscope. A photograph was made of the observation. With reference to the published solubilities,' several of these experiments, which contradict the chemical hypothesis, are listed as following: I. The coating of fluorite slime on the galena surface was light but the coating of galena slime on the fluorite surface was heavy. In a similar way, the coating of quartz slime on the galena was fairly light, but the coating of galena slime on the quartz particle was heavy. According to the chemical hypothesis, using the same constituents and regardless of which is the slime, the density of the coating should be expected to be the same. This, however, as shown above, is not true. Moreover, fluorite (CaF2), having a solubility of 16 mg.4a per liter of water, should not be

Jan 1, 1943

By J. H. Westbrook

IT is always of interest to document the origin of real microstructures which closely approach various idealized morphologies. Such instances constitute excellent bases for experimental studies of the effect of microstructure on properties. Typical examples include the eutectoid steels (lamellae) used by many investigators and the two phase Cu-Cr alloys (spheres) recently employed by Hibbard and Hart The present note describes a structure with cylindrical particles. In a study of certain alloys in the Cr-C system, an alloy was arc melted whose composition was very close to the aCr-Cr,C, eutectic (3.2 wt pct C, according to the latest phase diagram published by Bloom and Grant2). The alloy was not analyzed but previous experience with the melting technique employed indicates good correspondence between intended and analyzed compositions with negligible tungsten contamination from the electrode. The phases present in the alloy were identified by X-ray powder patterns as a chromium and Cr,C,. Typical micrographs, presented in Fig. 1, show unmistakable evidence of the cylindrical geometry of the carbide phase. The eutectic grains are randomly oriented and, consequently, only a few show the true fibrous nature of the carbide particles, most being cut so as to show slightly elliptical cross sections. Within any particular grain, remarkable uniformity is to be observed with respect to the size, shape, spacing, and orientation of the carbide particles. Length to diameter ratios have been estimated from the micrographs to be at least 250:1, with diameters of about lp. This alloy may be of further interest from different viewpoints. On the one hand, it might be used to check the applicability of the equations derived by Fullman3 for computing true particle dimensions of cylindrical particles from opaque random sections. On the other hand, it might be possible to extract the carbide particles from this alloy and repack them in a ductile matrix to form a synthetic structure of the type discussed by Metcalfe et al.4 With the large l:d ratio and the small diameter of the carbide fibers, it is likely that the interdefect distance in each fiber is sufficiently great to permit realization of a large fraction of the presumed high strength of the carbide. References 1W. R. Hibbard, Jr. and E. W. Hart: Dispersion Hardening of Copper-Chromium Alloys. AIME Trans., 1955, vol. 203, p. 200; Joun-nal of Metals, January 1955. 2D. S. Bloom and N. J. Grant: The System Chromium-Carbon. AIME Trans.. 1950. vol. 188. p. 41; JouRnal of Metals, January 1950. aR. L. Fullman: Measurement of Approximately Cylindrical Particles in Ooaaue Samples. AIME Trans.. 1953, vol. 197, p. 1267; Journal of Metals. ~ebtember 1953 4 A. G. Metcalfe, C. H. Sump, and W. C. Troy: Fiber Metallurgy. Metal Progress, 1955, vol. 67, p. 81.

Jan 1, 1958

By L. D. Woodworth, E. E. McGinley

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By E. E. McGinley, L. D. Woodworth

During the past several years has occurred what, in the light of future events, may aptly be called the rebirth of the acid Bessemer process. The increased attention given to the technical and metallurgical details involved in the production of Bessemer steels has been exceedingly fruitful, and indicates the value of further research and p1ant development. In times like these, when the steelmaking capacity of the country is operating at a maximum rate to supply materials for the national defense program, it behooves the Bessemer operator not only to strive to increase production but also to maintain a high standard of quality. The opportunity is ripe, it seems, to recapture fields of application once considered the birthright of Bessemer steels, but supplanted in recent years by open-hearth grades. This involves cooperation all along the line, from the blast-furnace operator to the metallurgical contact man and salesman. The metallurgist's part in this program involves the study of the many steelmaking variables and the measures necessary to ensure constancy in the finished product. It is equally important that the knowledge gained be disseminated widely to ensure the wise application of Bessemer steels in new fields. The merits of Bessemer steels for certain work are well understood. The combined properties of good weldability, machinabil-ity and stiffness are unique and fully explain the strong entrenchment of Bessemer steels in certain fields; e.g., skelp for small butt-weld conduit, screw steels machined in automatics, and certain tin-plate applications. It is the purpose of this paper to review briefly the physical properties of Bessemer steels as contrasted with those of open-hearth steels, to discuss control measures now employed in the making of Bessemer steel, and to consider the advantages derived from the use of these control measures. Physical Properties oF Bessemer vs. Open-hearth Steels A number of Bessemer blows and open-hearth heats were tested for tensile strength, ductility and impact strength. The steels selected were confined to sections from 3/4 to 1 1/4-in. diameter, inclusive, and the carbon content covered was sufficient to yield parallel ranges in ultimate strength for the comparison. Other factors, such as the extent of deoxidation of the steel and variations in chemistry, were kept as comparable as possible. Machined test pieces of 0.505-in. diameter with an 8-in. gauge length were pulled. The data obtained are shown in Fig. I, ultimate strength being plotted against carbon content. This graph shows that for equivalent carbon content Bessemer steel has on the average 15,000 lb. per sq. in. greater tensile strength and, conversely, for the same tensile strength Bessemer steel requires on the average 0.14 per cent less carbon. The average phosphorus content for the Bessemer steel was 0.090 per cent,

Jan 1, 1941

By R. I. Jaffee, J. G. Dunleavy, W. Hodge, H. R. Ogden

Early in 1946, at the instigation of the U. S. Army Signal Corps, the authors made an extensive survey of the available literature covering high-strength, high-conductivity alloys. For the purposes of the Signal Corps, the minimum tensile strength to be considered was 150,000 psi, together with at least 50 pct IACS conductivity. No single alloy was found to be in production, or mentioned in the literature, which had this combination of properties. The constitution diagram for the iron-copper alloys is not well established in the respect to the two-liquid region. Fig I, taken from the 1939 Ed. of the ASM Metals Handbook, shows a two-liquid system existing above the liquidus temperature, but disconnected from it. Although Ruer and Fickl and Ruer and Goerensz definitely established the fact that two liquid layers could occur in the system, Ruer3 was not convinced that the line of immiscibility was closed in the center. Maddocks and Claussen4 found no liquid immiscibility at temperatures up to 157oOC in alloys containing almost no carbon. Although the diagram would indicate age hardening of the copper-iron alloys is possible, Hanson and Fords found that little hardening effect could be obtained. However, Gordon and Cohen6 reported that the response is better if the quenching is very efficient. Although iron has a potent effect on the conductivity of copper, Hanson and Fords have shown that, when hot-rolled copper-iron alloys are aged at 1200°F, the electrical conductivity decreases sharply with iron contents up to 0.2 pct Fe, and then levels off at conductivities between 60 to 70 pct IACS with compositions to 2.1 pct Fe. They also found that aging did not increase the tensile strength, although increasing iron content gave a moderate improvement in strength. High-strength copper-iron alloys, usually containing about 60 pct iron, had been reported by Smith and Palmer.7 They found that an alloy containing 56.4 pct copper, 0.21 pct magnesium, balance iron, would give a maximum tensile strength of 170,000 psi and an electrical conductivity of slightly over 35 pct IACS. The alloy could also be processed to have I50,000 psi tensile strength, and about 41 pct I.\CS conductivity. Decreasing the iron content increased the electrical conductivity, but the long mushy range during freezing of the alloy containing 10 to 20 pct iron made the production of good castings difficult. In spite of the difficulty encountered by Smith and Palmer with alloys of around 20 pct iron, it was decided to make a rather complete investigation of this type of alloy. As a result of this investigation, a method of alloying and fabricating copper alloys containing 10 to 15 pct iron was developed

Jan 1, 1949

By I. D. Shah

A roasting procedure for synthetic copper sulfide which results in a reproducible transient melting at 450° and 470°C is described in this paper. Possible causes for this melting phenomenon are suggested, and also a procedure to avoid it during the roasting. This melting is believed to be responsible for the occasional occurrence of stickiness in the commercial roasting of copper sulfide concentrate. Many workers have studied the roasting of copper sulfides, but only Lewis et al. have reported that fusion and, in some cases, fusion with "boiling" occurred in the neighborhood of 450°C. The DTA and TGA apparatus, the materials used in this investigation, and the discussion of chemical reactions occurring during the CuS roasting are described in an earlier publication. CuS, in the form of either pellet or powder, was heated at 280° to 330°C in a flowing air or 30% 02: 70% N2 atmosphere. Heating was continued at this temperature until no further weight increase due to sulfates formation was observed on the TGA thermogram. This is believed to be due to the inability of SO, to diffuse out from the sulfate layer on the surface of the pellet, thus halting the sulfate-forming reactions. Hereafter, the sample oxidized in this manner will be referred to as "partially oxidized CuS." X-ray analysis and microscopic examination of a polished cross section of a partially oxidized CuS pellet showed the following order of layers starting from the center of the pellet: Cu2S, Cu2O, CuO • CUSO4, and CuSO4. A bare thermocouple inserted in the center of a partially oxidized CuS pellet (2.5 g) did not indicate any noticeable change in the temperature of the pellet when melted at 450° to 470°C in an inert or oxidizing atmosphere. During the preparation of a partially oxidized pellet, the temperature of a CuS pellet increased by 50°C due to the exothermic formation of sulfates in air at 320°C. The endothermic peak associated with the melting phenomenon at 450°C is shown in [Fig. 1.] A CuS pellet (0.2 g) was oxidized in flowing air (150 cc per min) at 10°C per min up to 320°C and held there for about 2 hr. Then, N2 replaced air and heating was continued up to 500°C. The exothermic peak at 320°C represents an overall formation of sulfates, and an endothermic peak at 450° to 470°C represents the melting phenomenon. To observe the melting visually, a small (50 mg), partially oxidized CuS pellet was heated (in static air) in a hot-stage microscope. The melting phenomenon was observed on an auxiliary TV screen. The sample

Jan 1, 1976

By B. Wilshire, W. J. Evans

W. J. Evans and 8. Wilshire SEVERAL recent investigations1-6 have shown that the strain, c, during transient and steady-state creep is well-represented by the expression: € = e0 + et(l - e-mt) + Esl [l] where Eo is the instantaneous strain on loading, ET the total transient strain, C, the steady creep rate! and m a constant relating to the rate of exhaustion of transient creep. However, it has been noted6 that deviations from this equation occur over the first 10 to 15 pct of the transient stage, when the creep rate, (. decreases more rapidly than is predicted by this equation. This rapid decrease has been attributed to a large change in work-hardening coefficient. It 1s widely accepted that steady-state creep results from a balance between the rate of strain hardcning h and the rate of recovery r (=-s(st) as: dE/dt = Es = r/h [2] Comparison of values obtained for h at the end of the initial extension and during steady creep suggests that h increases several fold during the transient stage. which has the effect of reducing the creep rate proportionally.7 To examine the dependence, on r and h, of the deformation behavior during transient and steady-state creep. a series of constant-stress creep tests was carried out at 413°C at 6000 psi using 70-30 a brass. Prelinlinary investigation showed that. with this material. the transient stage constituted a significant portion of the total creep life (-0.4tf. where tf is the time to fracture). The alloy. obtained from Metals Research Limited. was made from high-purity copper, 99.999 pct. and zinc. 99.99 pct. Heat treatment at 675°C for 4 1/2 gave a uniform grain size of 5 mm-1. Details of specimen preparation and creep testing procedures have been given previously.6 Values of h (?s/?E) were determined by measuring the instantaneous strain. ?E. which occurred on increasing the stress during creep by a small amount. ?s. Similarly. v (= -?s/ ?t) was derived from the incubation period. At, after a small decrease in stress.' Several values of v and h were obtained throughout duplicate creep tests. using different stress increments in the range 300 to 800 psi. The accuracy with which Eq. [I] represents the present creep curves was established by determining the best value of the constants Es, Et, m , and 6, using a digital computer program based essentially on the graphical solution for this equation devised by Conway and Mullikan.9 About 40 strain/time readings were taken during transient and steady-state creep. Over most of the creep curve, the average difference between the measured reading and the calculated strain at the appropriate time was less than 0.0001. However.

Jan 1, 1969

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By Herbert H. Kellogg

In 1930, Taggart, Taylor and Knoll1 found that addition of various electrolytes to suspensions of ground minerals resulted in the stopping or starting of Brownian movement of the suspended particles. On the basis of the many new facts found, they rejected the " classical"† theory of Brownian movement and proposed an "ioniza-tion " theory. This new theory was further supported in later publications by Taggart.3,4 The acceptance of the ionization theory by men in the field of flotation may be judged by the mention given this theory in Gaudin's "Principles of Mineral Dressing,'16 Wark's "Principles of Flotation,"8 as well as in a recent paper by Fitt, Thomas and Taggart.7 The proponents of the ionization theory have gone further than the mere statement of the new theory. A parallelism between the Brownian movement of mineral particles and their behavior in flotation was reported.1,3,4 Likewise, the correlation between flocculation-dispersion of mineral particles and the Brownian movement of these particles has been investigated.' Bankoffl5 has suggested that "slime-coating" can also be directly correlated with the Brownian movement of the slime particles. In each of the instances mentioned it is the ionization theory of Brownian movement that has been used to "explain" the correlations that were found. The essential conflict between the kinetic theory and the ionization theory can be understood best by a brief description of each. The kinetic theory* proposes that Brownian movement is caused by the impacts of liquid molecules against the solid particles. At any instant of time, the molecular impacts on all sides of the solid particle will not balance, and the particle will receive a push in some direction. According to this theory, dl particles suspended in a liquid are in Brownian movement. However, if the particle is very large, the impacts on all sides will very nearly balance and the motion will not be noticeable. Another factor, besides the size of the particle, that affects the magnitude of the Brownian movement is the viscosity of the liquid—the greater the viscosity, the less the displacement of particles by Brownian movement. This theory has been verified experimentally by measurement of the velocity of Brownian movement, and by measurement of the compacting of suspensoid particles under the influence of gravity.2 The originators of the ionization theory found that he addition of various electrolytes to slime pulps caused cessation or commencement of Brownian movement, depending upon the chemical nature of the particle and the electrolyte. The Brownian movement of quartz particles was observed to stop upon the addition of Certain electrolytes, where the conditions of the experiment prevented flocculation

Jan 1, 1947

By J. A. Barr, R. B. Burt, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By R. B. Burt, J. A. Barr, I. S. Tillotson

THE pumping of solids in water suspension is an important part of many metallurgical and mining operations. In most cases, it is still in the rule of thumb category for which no universal formula has been developed, and much research is needed. Because of the limited and incomplete data available, this article may be classed as an experience paper, which is presented with the hope that some contribution will be made toward the development of the so-called universal formula. This formula, if and when developed, may be evolved from several factors, many of which are not now available for general application. The designing engineer is interested in obtaining accurate forecasts on: 1—the minimum velocities needed to prevent choke-ups in the pipeline, which in turn dictates pipe sizes, 2—power required for pumping, 3—pump selection. The basic factors for a given problem will include: 1—weight per unit of time of solids to be handled, 2—specific gravity of solids, for calculation of volume, friction and power, 3—screen analysis of solids with the colloidal acting, i.e., the slime fraction, a very important factor, 4— shape of particle or some means of determining a friction constant, 5—effects of percentage of solids, 6—development of a viscosity factor to be used in the overall calculations, 7—calculation of the lower limits of pipeline velocities permissible, 8—calculation of total head, pump horsepower, and 9—setting up of pump specifications. In certain limited cases horsepower and total heads and minimum velocities may be computed and a suitable pump selected from basic data, but in many cases, as in mining of Florida pebble phosphate, experience rather than a hydraulic formula still should be used as a basis of selection. Pumping Florida Pebble Matrix Pumping at the Noralyn mine of International Minerals and Chemical Corp. will be used as an example. Other areas will vary as to the characteristics of the matrix, especially the slime content. A typical screen analysis of this matrix is: +14 mesh, pebble size,* 2.1 pct; —14 +35 mesh, 11.4 pct; -35 +I50 mesh, 60.5 pct; -150 mesh, 25.0; total, 100 pct; moisture in bank, 20.0 pct; weight per cu ft in bank, 120 lb. The —150 mesh fraction may increase to as much as 35 pct in adjacent areas. When thoroughly elutriated, the matrix has a relatively slow settling rate, which is an important factor in permitting lower pipeline velocities without choke-ups. Exact data is not available to evaluate settling rates. For a factor of 100 a suspension of clean building sand in water is suggested. When pumping long * Pebble is a commercial designation for the coarser fraction of finished phosphate from a washer, usually +14 mesh. distances, a quick settling matrix allows the coarser solids to settle out along the bottom of the pipeline, causing drag, turbulence, and increased friction. With a slow settling matrix as at Noralyn, turbulence acts to keep the solids in suspension at a lower friction head, regardless of the pumping distance. When the pebble content of the matrix, i.e., the + 14 mesh fraction, is in excess of 10 pct of the total solids, trouble may be expected from settling out even in normal pumping distances. To prevent choke-ups and maintain tonnage, an additional pump must be added in the long runs, where one pump would otherwise be satisfactory. A typical pulp handled is: total volume, 7800 gpm; water, 4500; solids pumped per hr, 4200 lb; sp gr pulp, 1.4; percent solids in pulp, 46.; pipe size, 16-in. ID; pulp velocity, 12.85 fps; probable critical velocity, 10 fps, as below this minimum velocity choke-ups would be numerous. In calculating friction heads the Armco handbook is used where a roughness factor based on 15-year-old pipe is set up. Because the pipe used in pumping matrix is smooth and polished because of the scouring action of the phosphate and its silica content, the head losses in the Armco table for water are practically the same as in pumping the Noralyn matrix through smooth pipe, plus the fact that conditions vary widely over short periods, making accurate determinations difficult to obtain. New pumps and pump changes are being tested continuously and a wealth of data built up. This has resulted in a substantial improvement and lower relative costs in pumping matrix. The Florida phosphate industry is constantly seeking to offset higher wage and material costs with improved technique. Until a few years ago a 12-in. discharge pump was commonly used, with heads as low as 80 ft. Sizes have gradually increased and heads more than doubled. For example, the following pump was placed under test at the Noralyn mine: make, Georgia Iron Works; size, suction 16 in., discharge 14 in.; impeller, 39-in. diam; motor, 600 hp, slip ring; full load speed, 514 rpm. The results were increased head, higher capacity than the older design, with fewer pumps in the line from mine to washer.

Jan 1, 1953

By C. E. Sims

IN an earlier paper by Sims, Moore, and Williams: data were given to show that hydrogen contents of 0.3 relative volume (0.00033 wt pct), existing at the center of 4-in.-square cast-steel coupons, could be removed by aging at 400°F for 125 hr. At the end of that time, complete restoration of normal ductility for the steel was obtained. Replicate specimens of the same steel were aged at room temperature up to 555 days or .18 1/2 months. At the end of that time, the hydrogen content at the center had fallen to 0.13 relative volume or 0.00015 wt pet, but there was no perceptible change in the ductility. On the basis of experience with accelerated aging of 1-in. and 4-in. coupons and room temperature aging of 1-in. coupons, it was predicted that, some time after two years and when the hydrogen content has been reduced to about 0.10 relative volume, there would be some recovery of ductility. One set of three bars remained, and these were held for 1310 days, or more than three years. Then tensile test bars were cut from the center, and these bars were sampled for hydrogen analysis at the time they were broken. The sample specimens were cylinders % in. in diam x 1 1/4 in. in length. The data showed that in this time the average hydrogen content had fallen to 0.096 relative volume or 0.00011 wt pct, and the ductility had increased sharply. Elongation had risen from 10 to 17.3 pct, while reduction of area increased from about 16 to 27.5 pct. On the basis of these data, fig. 1 was drawn to replace fig. 15 of the earlier paper. Extrapolation of the curves of fig. 1 indicates that it would require a period of about 2200 days or approximately six years at room tem- perature to reduce the hydrogen to the minimum value and to recover full ductility in the center of the coupons. The aging process apparently involves the movement of hydrogen from the interior to the surface of the bar and evaporation at the surface. This flux of gas presumably follows some diffusion mechanism, and an effort was made to use the aging data, obtained at room temperature and at 400°F, to calcu-late coefficients of diffusion, in the hope that they might indicate the nature of the diffusion. The conclusion was reached. however. that the data were inadequate for such a purpose.

Jan 1, 1951

By George C. Fryburg

The oxidation of platinum at high temperatures (above 800°C) is controlled by boundary-layer diffusion, except at the lowest pressures. The rate of oxidation is determined by the rate of diffusion of oxide through the boundary layer away from the platinum. This is in contrast to the situation in tungsten and molybdenum oxidation, where the rate is controlled largely by the diffusion of oxygen through the boundary layer towards the metal. The difference in mechanism is a consequence of the much lower rate of oxidation of platinum. Evidence is presented that supports this mechanism for the oxidation of platinum. SOME years ago we reported1 a study of the oxidation of platinum in ordinary oxygen in the temperature region above 800°C, where the oxide is volatile. All the data available up to that time had been obtained with platinum crucibles or plates heated in tube furnaces. The results were widely variant and highly dependent on the flow rate of gas through the furnace: the faster the gas flow rate, the higher the measured oxidation rate. These results indicated to us2 that reaction equilibrium was being approached in the furnace and that the rate was diffusion limited. To minimize these effects, we employed1 electrically heated ribbons placed in a cooled bulb. We were primarily interested in the low-pressure region, but some experiments were performed at pressures up to 1 atm. We found a peculiar pressure dependency which was explained on the basis that the rate of oxidation was proportional to the pressure at all pressures, but that with increasing pressure an increasing fraction of the volatilizing oxide was back-reflected to the ribbon by the surrounding gas molecules. The oxide molecules are not stable at the temperature of the platinum and are decomposed on impact, the platinum being re-deposited on the specimen. Because of the limitations of space, this explanation was offered summarily without detailed support. Recently, Jaffee and associates3, 4 have suggested that the pressure dependency of our data up to 0.5 torr could be explained on the basis of a Langmuir-type adsorption of molecular oxygen followed by dissociation. Since the correct explanation of the effect of pressure on the oxidation rate is a necessary requirement to the development of the basic mechanism of the oxidation reaction, we felt that the back-reflection theory should be presented in more detail. This is the object of the present paper. RESULTS AND DISCUSSION A typical set of results showing the pressure dependency of the oxidation reaction is presented in Fig. 1, where we have plotted, on logarithmic scales, the rate of oxidation, R, vs the pressure, p. For comparison some results of Krier and Jaffee4 and of Raub and plate5 are also shown. These data were taken at atmospheric pressure using furnaces. The effect of reaction equilibrium within the furnace is apparent from the much smaller values that these observers obtained: Raub and Plate In O2 found a rate of 3.1 µg cm-2 hr-1 compared to our value of

Jan 1, 1965