Search Documents

By Earl Greiner

THE constitution of the iron-silicon alloys containing from 14 to 33.4 weight per cent silicon has been studied by a number of investigators, whose results have been reviewed in a monograph published by the Engineering Foundation1. In these previous researches, the solubility of silicon in iron was determined by thermal, microscopic or magnetic methods and the compound Fe3Si2 was reported to be stable at tempera-tures from 0 to approximately 1030° C. This paper describes the results of an X-ray investigation of the solubility of silicon in iron and gives data which prove that the Fe3Si2 phase is unstable below 825° C. In order to obtain the present results on the solubility of silicon in iron, the authors have utilized the lattice constants of the alpha-phase iron-silicon alloys given in a previous publication2, and also some addi-tional data which will subsequently be described.

Jan 1, 1936

By Robert Mehl

IT has been shown that quenched iron of high purity exhibits a Widmanstätten figure much resembling martensite in appearance.1 This figure exhibits a maximum of four directions of the surface traces that characterize it, suggesting that a Fe forms from y Fe in plates parallel to the {111}, octahedral, planes in the y lattice. Because of this, and also because of the general similarity to the structural appearance of martensite and to the Widmanstätten figure obtaining in slowly cooled hypoeutectoid steels it has been suggested2 that the orientation relation-ships obtaining between the y and a phases in pure iron are identical with those demonstrated in martensite3 and in slowly cooled hypoeutectoid steels,4 and indeed that the crystallographic mechanism of formation of a Fe from y Fe is the basic mechanism determining the orientation relation-ships found in both martensite and in slowly cooled hypoeutectoid steels. This paper will present experimental evidence in support of this view.

Jan 1, 1934

By F. E. Luborsky, K. T. Aust

RECENT interest has been shown in utilizing solid-state techniques for obtaining large oriented grains in the Alnico Alloys.1-4 Unfortunately, due to the inherent brittleness of these materials it is difficult to introduce sufficient imperfections by deformation to support the nucleation and growth of new, recrystallized grains. As a result, recrystal-lization methods for obtaining large grains, such as the strain-anneal technique, do not appear to be feasible. Steinort et a1.2 used a combination of a thermal gradient and internal strains to obtain large single crystals of Alnico 5 from a poly crystalline casting by annealing at temperatures above 1200°C. It was suggested that the strains were the result of the precipitation of the y phase which exists between -850° and 1200°C. The purpose of the present study was to determine if the grain size of the cast Alnico alloys can be markedly increased by solid state techniques involv-

Jan 1, 1963

Florida State Geological Survey, Tallahassee, Fla Herman Gunter, State Geologist A list of publications will be sent upon request Citizens of the state may obtain publications available without cost, others may have them for postage, or they can be sent express collect Twenty Annual Reports have been issued from 1908 up to and including the 21st-22nd Annual Report (1931). Only three are now available; 4th Annual Report (1912), 15th (1924) and 18th (1927) Reports since 1921 contain statistics on mineral production. All reports contain papers on various subjects, many of which are still available separately, and are so indicated in the list of publications. Seven bulletins have also been issued, principally of interest to paleontologists Bulletin 7, The Pensacola terrace and associated beaches and bars in Florida (1931), is of more general interest Bulletins will be sent upon receipt of postage. Thirteen Press Bulletins, most of which are available, have also been issued, but are of minor interest

Jan 1, 1933

By N. Mao

This paper presents the results of a research effort to develop a technique for estimating in situ stresses by measuring stress-induced velocity anisotropy around a borehole. Relevant parameters required to make the estimate were identified and measured in the laboratory on a 35.6 cm (14.0 in) cube of Nugget sandstone with a 10.2 cm (4.0 in) diameter hole, under biaxial loading. Two pairs each of radially and tangentially polarized transducers were placed inside the hole with displacement directions either parallel or perpendicular to the principal stress directions. With this configuration, relative travel times were measured by both a pulsed phaselocked loop technique and a cross correlation of digitized waveforms. The biaxial velocity data were used to back-calculate the applied stress. The standard deviation of the differences between the calculated and applied stresses is 0.62 MPa (90 psi) for a stress level up to 8.63 MPa (1250 psi).

Jan 1, 1984

By R. G. Fenish

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from Hoffman:"

Jan 1, 1967

During the year 1915 the Committee received 161 manuscripts, which were treated as follows: 3 accepted for. New York Meeting (110th) . 64 accepted for San Francisco Meeting (111th) 49 accepted for New York Meeting (112th) 3 accepted for Arizona Meeting (113th) 29 rejected 4 returned to authors for revision and not yet accepted 9 in committee. 161 Every paper which was presented at the San Francisco Meeting was published in advance in the Bulletin with one exception. The work of the Committee has been systematized and. the Executive Committee of the Committee on Papers and Publications has given prompt attention to all manuscripts, with the result that every paper received by the Committee on Papers and Publications is in the hands of the, printer within 30 days thereafter, unless delays occur owing to questions as to acceptability, in obtaining from the author permission for revision, or other like causes.

Jan 2, 1916

Plans for the fall meeting of the AIME, to be held in conjunction with the Centennial of Engineering -marking the 100th anniversary of the Society of Civil Engineers-indicate that the Chicago gathering will be one of the most significant in Institute history. Headquarters for the six divisions represented will be the Palmer House. Twenty technical sessions will be held from September 3 to 6, with papers of industry-wide impact to be presented. The papers will follow the theme of the celebration-a century of engineering progress. The MBD will start the ball rolling with morning and afternoon sessions Thursday, September 4. A luncheon also will be held. MBD has scheduled morning and afternoon sessions for the following day as well. MGGD, Iron and Steel, and the Coal Div., will hold sessions Friday afternoon. The Industrial Minerals Div. plans an executive meeting, 5 pm, Friday. Geology Subdivision is slated for morning and afternoon sessions Saturday. The Coal Div. will meet again Saturday morning.

Jan 1, 1952

The Second Pan-American Scientific Congress will be held under the auspices of the United States Government in Washington, D. C., Dec. 27, 1915, to Jan. 8, 1916. The organization officers are John Barrett, LL. D., Director General of the Pan-American Union, Secretary General; Glen Levin Swiggett, Ph. D., Assistant Secretary General; the headquarters of the Congress are the Pan-American Union, Washington, D. C. The program of the Congress is divided into nine main Sections, which are given below with the name of the Chairman of each Section: 1. Anthropology, William H. Holmes, B. S., Smithsonian Institution, Washington. 2. Astronomy, Meteorology, and Seismology, Robert S. Woodward, Ph. D., Carnegie Institution, Washington, D. C. 3. Conservation of National Resources, Agriculture, Irrigation and Forestry, George M. Rommel, B. S., Bureau of Animal Industry, Department of Agriculture, Washington, D. C. 4. Education, P. P. Claxton, LL. D., Bureau of Education, Washington, D. C.

Jan 12, 1915

By N. R. Adsit

THE B-Ni system was chosen for this study because of the great interest being shown in boron-fiber-strengthened composite materials. Boron fibers were obtained from Texaco Experiment, Inc. They average 4.2 mils in diam with a 0.5-mil tungsten wire in the center. In order to make the diffusion couple, the fibers were included in the nickel matrix by electroforming. The samples were placed in a preheated furnace for the desired temperature and length of time. Sectioning and polishing the samples revealed concentric rings as shown in Fig. 1. The average penetration distance, X, was calculated by measuring the radius of the second phase (the white shell in Fig. 1) and subtracting the original radius. The second phase was identified as NiB by X-ray diffraction. This allows the kinetics of the formation of the phase NiB to be calculated by Eq. [I], which is taken from offman:"

Jan 1, 1967

By C. N. Reid

In the course of annealing studies on molybdenum, it has been observed that a carbide precipitates preferentially on internal and external surfaces. The evidence for this is as follows. Electropolished bend specimens prepared from two grades of commercial molybdenum were loaded in a closed but unsealed tantalum can, and were annealed for 1 hr at 2000°C under a vacuum of 1 x 10-4 torr. The compositions of these materials are summarized in Table I. The samples were then slowly cooled at an average rate of 10°C per min, and were examined when cool. The surfaces of specimens prepared from Molybdenum A were consis- tently clean and featureless, except for thermally etched grain boundaries, see Fig, l(a). On the other hand, Molybdenum B had surfaces containing many needle- and featherlike markings, see Fig. l(b). These features were present in all surface grains, and within a given grain belonged to families

Jan 1, 1965

By William M. Kester

INTRODUCTION The Coal Research Bureau of the School of Mines at West Virginia University is presently conducting laboratory-scale tests to determine the technical feasibility of beneficiating pulverized coal and coal fines with high-intensity electromagnetic fields. Interest in magnetic processes for cleaning fine coals was stimulated by results obtained by Yurovsky, et a1 in 1958.1 This work, while not new in concept,2,3 indicated that pulverized coal which had been thermally treated in a rotary drum in the presence of superheated steam and air underwent thermo- chemical reactions. Films of the ferromagnetic minerals magnetite (Fe2O3), hematite (Fe3O4), and pyrrhotite (FeS[3]) were reported to be formed on the surfaces of the pyrite grains associated with fine coal during the foregoing treatment at temperatures ranging from 120 to 360°C. After thermal treatment the coal was magnetically separated in an experimental magnetic device having a field strength of 10,000 oersteds.

Jan 5, 1965

By Donald Ingvoldstad, Harold E. Lee

At Bunker Hill the original charge storage and preparation system was installed in 1917 to accommodate lead-silver gravity mill products. Only minor tonnages of wet fines such as vanner and flotation concentrates were received. Charge flux and diluent requirements were provided by an ample supply of siderite middlings and coarse limerock. While oversize material was crushed through Y4-in., the use of roll crushers in series resulted in a more or less granular, free-running charge of adequate porosity. Under such conditions, receipts could be proportioned directly from receiving bins, and suitable blending was obtained by passing the resultant layered composite through a small Stedman disintegrator. This elementary system served well for production and smelting of an extremely lead-rich sinter, in the low column blast furnace. Here sinter physical quality is less critical, and appreciable quantities of raw flux and oxidized ore may be charged directly to the blast furnace without seriously impairing furnace capacity.

Oct 1, 1956

By W. Hume-Rothery

RECENT interest has been shown in utilizing solid-state techniques for obtaining large oriented grains in the Alnico Alloys.1-4 Unfortunately, due to the inherent brittleness of these materials it is difficult to introduce sufficient imperfections by deformation to support the nucleation and growth of new, recrystallized grains. As a result, recrystal-lization methods for obtaining large grains, such as the strain-anneal technique, do not appear to be feasible. Steinort et a1.2 used a combination of a thermal gradient and internal strains to obtain large single crystals of Alnico 5 from a poly crystalline casting by annealing at temperatures above 1200°C. It was suggested that the strains were the result of the precipitation of the y phase which exists between -850° and 1200°C. The purpose of the present study was to determine if the grain size of the cast Alnico alloys can be markedly increased by solid state techniques involv-

Jan 1, 1963

The Arizona Committee, consisting of GERALD F. G. SHERMAN, Chairman, ARTHUR NOTMAN, Secretary, NORMAN CARMICHAEL, B. BRITTON GOTTSBERGER, W. L. CLARK, J. C. GREENWAY, W. G. MCBRIDE, FOREST RUTHERFORD, has arranged the following program for the Arizona Meeting, which has been approved by the President of the Institute and by the Executive Committee. It is printed herewith for the information of members, and probably will not be changed in any material respect. Sunday, September 17, 1916.-Arrive at El Paso, Texas, 2.40 P.M., leave 10.20 P.M. Monday, September 18, 1916.-Arrive at Deming, N. Mex., .12:47 A.M. Arrive at Santa Rita, N. Mex., 4.00 A.M., where luncheon will be served, after which there will be a visit to the Chino mines. From there the train will proceed to Hurley, N. Mex., where a visit will be made to the mill of the Chino Copper Co.

Jan 7, 1916

By Benjamin C. Koskiniemi

Introduction When evaluating any ore body, one of the first questions concerns the ore reserves. In the case of an open pit mine, this is not possible to answer reliably until the ultimate (final) pit limits have been established. Techniques used in designing an ultimate pit are classed as (1) manual, (2) computer, and (3) combined manual-computer. This chapter will describe how manual techniques can be utilized in designing an ulti¬mate pit Certain economic and design criteria must be established before the actual design begins In order to begin designing an ultimate pit, it will be assumed that the engineer already has the following data available (1) vertical sections, (2) horizontal sections for each level, (3) stripping curve, (4) bench height, (5) bank slope angle between levels, (6) level berm width, (7) roadway width, (8) pit slope angles at ultimate pit limits (estimated average including roads and ramps and between roads and ramps), and (9) minimum width of pit bottom

Jan 1, 1979

By Ellsworth Daggett

THE system of pitwork used with the Cornish pumping engine, and which, for want of a better name, we may call the Cornish system of pitwork, consists essentially of a series of plunger-pumps, situated one below the other, in a shaft or incline, the plungers being operated by a rod called the pitman or pump-rod, which must, therefore, extend from the motor at the surface to the lowest pump. The subject will be best understood by reference to Fig. 1, in which k may be taken as typical of the ordinary plunger-pump, in which S is the suction pipe, u, the lower valve situated in the H piece T; v, the upper valve situated in the valve-box O; I, the mounting-pipe or column through which the water is carried to the surface; L, the plunger-barrel, and P, the plunger working through the stuffing-box, and actuated by the branch rod r, which is attached to the main pump-rod, R. The action of the pump is as follows : On the ascent of the plunger, acting now by suction, the water flows from the reservoir through the valve u, into the barrel, L. On the descent of the plunger, the water is forced up through the valve, v, which acts merely as a check valve, into the pipe, I, through which it is, at each successive down-stroke of the plunger, forced upward until it reaches the next reservoir, from which it is taken by another similar pump, and so on until it reaches the surface or drain-tunnel. The pump is obviously only single-acting, i. e., it acts only during one-half of its entire stroke. The weight of water raised during the up-stroke of the plunger is equal to the weight of a column of water whose base is the area of the plunger and whose height is the mean distance between the plunger-face and the surface of water in the lower reservoir, a distance not usually exceeding 12 or 15 feet, and which obviously cannot under the most favorable circumstances, exceed 25 or 30 feet. The water forced up during the down-stroke is equal to the weight of a column of water whose base equals the area of the plunger and whose height equals the length of the mounting column above the mean position of the plunger-face, say from 150 to 300 feet. Almost all of the useful work, therefore, is done on the de-

Jan 1, 1879

By Arthur A. Center

HIGH GRADE zinc stocks were reported short early in 1943, but not Prime Western. Maximum production of High Grade was expected to be reached before the middle of the year, and demands of new brass mills were to take all of the increase. In February three premiums (A, B, C) of 2 3/4c. per lb. of zinc in ore were announced to encourage production from high-cost mines, the number of premiums being in proportion to estimates of ore-production costs.

Jan 1, 1944

By Joseph D. Weeks

FIFTY-eight years and a day, full of labor, of achievement and of honor had been completed when, at Pittsburgh, on the 5th day of May, 1892, the wheels of a life that had but just before lost its inspiration stood still, and the work here of William Powell Shinn was at an end. Born at Burlington, N. J., May 4,1834, he received such an education (and it was. the only school education he ever had) as the public

Jan 1, 1893

By Ross C. Anderson, William I. Weisman

THE manufacture of anhydrous sodium sulphate or salt cake from natural deposits in the United States has been in general somewhat of a marginal undertaking. Competition from foreign sources and from large quantities of byproduct sodium sulphate produced domestically in the manufacture of hydrochloric acid and other chemicals has existed and continues. For example, most of the sodium sulphate produced is a byproduct or co-product in the manufacture of hydrochloric acid through the reaction of sodium chloride with sulphuric acid. In recent years, many manufacturers of rayon have installed equipment to recover sodium sulphate from waste spin bath liquors; today this is an important source. Before World War II large quantities of sodium sulphate were imported from Germany. In 1949 imported material from Europe again appeared on the domestic market. Natural sodium sulphate from Canada in substantial quantities also enters the United States markets. Despite this kind of competition, numerous attempts have been made to exploit various natural deposits of sodium sulphate in this country, but only a very few of these have survived economically over a period of years. One of these few operations is the plant of the Ozark-Mahoning Co. located 13 miles south of Monahans in West Texas. Several factors contributing to the successful life of this plant may be summarized as follows: 1—Geographical location. Monahans is reasonably close, freightwise, to the Kraft paper mills in Texas, Arkansas, and Louisiana; the Kraft paper industry is the greatest consumer of sodium sulphate in the United States. 2—Availability of natural gas as low cost fuel. Proximity of the natural gas fields of West Texas has been a tremendous asset, as the availability of low-cost natural gas is to all industry throughout the Southwest. 3—The nature of the deposit. The occurrence of sodium sulphate brines in southeastern New Mexico and West Texas has been very well described by Lang,' who writes that the brines are found in the Castile formation of the Delaware basin. Here weathering has altered the anhydrite so that a relatively porous gypsiferous zone overlies a dense impervious mass of anhydrite. This porous zone provides traps where percolating ground waters that have picked up soluble salts may lodge. These traps or pockets are the natural brine reservoirs exploited at Monahans. Although several hundred wells have been drilled, currently some 25 wells serve to supply brine to the plant. All are within 1 1/2 miles of the plant and are conveniently tied together by an electric power system serving electric motors driving the pumps. Having the raw material in the form of a brine which can be pumped from shallow wells makes possible much simpler and more efficient handling than if it were in form of solids. By contrast, other deposits of sodium sulphate, such as those in Arizona, Nevada, and North Dakota, are in the form of the solid minerals, thenardite and mirabilite, which present somewhat more of a mining and mineral dressing problem.' The largest producer of sodium sulphate from natural sources in the United States is at Searles Lake, Cal., and there a brine also is utilized. 4—Water. Substantial quantities are needed for cooling towers and for operation of gas engines. An area underlain with brine is not a promising source of fresh water, but fortunately, after a long search, an adequate supply was found nearly two miles from the plant. It may be appropriate to discuss briefly the grades of sodium sulphate offered on the market. Salt cake is the name usually applied to the grade of sodium sulphate used by the Kraft paper industry. It may be a low analysis byproduct, 95 to 97 pct sodium sulphate, with as much as l 1/2 to 2 pct residual acid, or it may be a natural product. Usually salt cake is considered a low grade product, but a great deal of a higher grade of material is marketed under this name. The specifications for glassmakers' salt cake are somewhat higher than those of the paper industry, usually requiring 98 pct sodium sulphate. Technical anhydrous sodium sulphate is a high grade material and usually exceeds 99 pct sodium sulphate. It finds the biggest market in the textile industry and is used as a builder in some synthetic detergents. Glauber's salt, Na2SO4. 10H20, is usually of high purity. Preferred for some uses, it normally has been recrystallized from an anhydrous salt. A unique manufacturing process has been developed at Monahans. This process results in the production of an exceptionally high grade of salt cake, and qualifies for nearly all uses, including many which specify the technical anhydrous grade. All of the finished product, which is very white, passes a 10-mesh U. S. Standard screen, and is retained on a 200-mesh U. S. Standard screen. It is over 99 pct Na2SO4 with main impurities being sodium chloride and magnesium sulphate. Iron content is less than 0.01 pct. As mentioned, the raw material at Monahans is a brine drawn from wells. Attention was first attracted to this location because a so-called alkali

Jan 1, 1954