Search Documents

By W. V. Green

Creep of tantalum was measured at temperatures from 0.6 to 0.89 of the absolute melting temperature. The creep curves include first, second, and third stages. Steady-state creep rate depends on the fourth power of stress. The activation energy for creep throughout this temperature range is approximately 114 kcal per mole, measured by the aT technique. Subgrain formation occurs as a result of creep strain, and pile-up dislocation arrays are observed in etch-pit patterns. BECAUSE of its high melting point-which is exceeded only by those of rhenium and tungsten—and its high room-temperature ductility compared to most of the other high-melting-point metals, tantalum will undoubtedly be utilized in an increasing number of high-temperature applications. Alloying studies directed toward increased high-temperature strength must use data on tantalum itself as a base line in order to evaluate the effectiveness of the alloying additions. However, to date, no systematic study of creep of tantalum at temperatures above one-half of its melting point has been reported in the literature. Conway, Salyards, McCullough, and Flagella1 have measured linear creep rate of tantalum sheet as a function of stress, but at only one temperature, 2600°C. This paper describes a relatively thorough study of the high-temperature creep of tantalum. METHOD Material Tested. The commercially supplied, l/2-innch-diameter tantalum rod used for this work was electron-beam-melted, cold-forged, rolled, swaged, cleaned chemically, and vacuum-annealed for 1 hr at 1000°C, all by its manufacturer. The vendor's analysis included 60 to 170 ppm C, 3.4 to 4.2 ppm H, 60 to 80 ppm 0, 15 ppm N, and a hardness ranging from 66 to 81 Bhn and averaging 76 Bhn. Creep eimens Used. Two creep-tested specimens are shown in Fig. 1. The 1/4 in.-diameter gage section was 3/4 to 1 in. long, and terminated either at shoulders 5 mils high or at 20-mil-diameter tantalum wires spot-welded to the circumference of the gage section. Both kinds of shoulders served equally well as fiducial marks for optical strain measurements. The spot welding did not alter the creep behavior in any detectable way; the 5-mil- high sharp shoulders did not result in any detectable localized effect on the strain. Before testing, each tensile bar was first mechanically polished -id then electrochemically polished according to the method referred to by Forgeng2 as the "Thompson Ramo Woolridge" method, which was suitable for tantalum after small adjustments of technique were made. Two tensile bars tested at low stresses had 1/8-in.-diameter gage sections and utilized only the weight of the bottom grip for the applied load. Although these diameters were smaller than were desired for other reasons, applied loads were known with high precision in the tests in which they were used. Testing Procedure. Two different constant-load creep-testing machines were employed, one of which has been described by Smith, Olson, and Brown.3 In both, the tensile bar is held vertically on the axis of a cylindrical tungsten tube or screen heater by threaded tungsten grips. The tensile bars and associated grips are heated by radiation from the incandescent heaters, which are heated by their own electrical resistance. Both testing machines use pins to hold the bottom grips in place. The load is applied to a tensile bar through hanging weights, a constant force-multiplication lever, a pull rod sealed to the chamber lid, and a top grip threaded to the pull rod at one end and to the tensile bar at the other. In one machine, the vacuum seal is a bellows with a low spring constant; in the other, the seal involves a rotating "0 ring". With the latter, rotation is converted to translation with a crank shaft, so that elongation of the tensile bar is accommodated with no change of tensile load. The incandescent tensile bar is viewed by an external optical system through slots in the radiation shields and heater, and an enlarged image is projected on a ground-glass screen. Gage-length measurements are made on this image with cathetometers on traveling microscopes. With regard to creep-test results, the two machines were identical. Thorium oxide coatings were applied to the threaded ends of the tensile bars, to prevent diffusion welding of the tensile bars to the grips during testing. Specimen temperatures were measured with an L. & N. optical pyrometer which had been calibrated against a standard carbon arc, and were corrected fir window absorption by calculation from the measured spectral transmittance of the quartz observation windows. Longitudinal temperature gradients in the tensile-bar gage length and temperature drifts during testing were detectable but small, and were estimated to be 10°C or less. Accuracy of temperature measurement was confirmed by comparing the temperature measured on the surface of a special

Jan 1, 1965

By P. Rama Rao, D. H. Sastry, T. R. Anantharaman

Deformation (a) and twin (a') stacking-fault densities in cold - wor ked filings of fcc silver alloys containing 2, 4, and 6 wt pct Sb have been estimated from Debye-Scherrer peak shifts and asymmetries, respectively. Evidence has been obtained for a possible strain-induced transformation in a two-phase alloy containing 9.0 zut pct Sb. Using Fourier analysis of X-ray line profiles, the effective particle sizes and root mean square strains have been determined for the three fcc alloys in the cold-worked condition. The values of the compound fault probability 0.5a + a') evaluated from peak shifts and asymmetries are in reasonable apeement with those derived from peak broadening. COLD work of fcc metals may produce both deformation and twin (also called growth) stacking faults, which can be detected and quantitatively estimated by X-ray diffraction techniques.' In addition to peak broadening, deformation faults produce a shift in peak positions and twin faults an asymmetry of the Debye-Scherrer reflections. Besides stacking faults, a reduction in the size of coherently diffracting domains and distortion within these also broaden the powder reflections of deformed fcc metals and alloys. Fourier analysis' of peak shapes provides quantitative infor- mation about the effective domain sizes, lattice strains, and also the compound fault probability (1.5a + a'), where a and a' represent deformation-and growth-fault density, respectively. The Paterson method2 for determination of a from peak shifts, the warren3 or wagner4 method for evaluation of a' from peak asymmetries, and the Fourier analysis for quantitative estimates of all the contributory causes of peak broadening have, in the course of the last decade, been extensively applied to obtain data for a number of deformed fcc metals and alloys. One of the useful results of earlier measurements of a in several solid solutions is a correlation between a and the solute valence as well as electron concentration per atom (p) in alloy systems based on a particular solvent. The work of Smallman and westmacott5 on Cu-Zn, Cu-A1, and Cu-Sn, of Foley, Cahn, and ~aynor' on Cu-Si and Cu-Ge, and of Rama Rao and Anantharaman7 on Cu-Si and Cu-Sb has revealed a common trend in the increase of a with p and also a with valency of the solute. Cahn and Davies' and Ad-ler and wagnerg have observed similar trends for silver alloys containing cadmium, indium, and tin. Data on a for silver alloys with a pentavalent solute element are not, however, available. It is primarily to fill this need that the present investigation on Ag-Sb alloys was undertaken. Utilizing the Patersonand Warren methods, values of a and a', respectively, have been determined in three silver alloys containing 2, 4, and 6 wt pct Sb. By Fourier analysis of the broadening of Debye-Scherrer peaks, effective particle sizes, lattice strains, and the compound fault probability (1.5a +a') have also been evaluated.

Jan 1, 1967

By I. R. Kramer

The apparent activation energy, U, JOY plastic deformation of aluminium, copper, and gold single crystals and polycrystalline aluminum was found to he dependent upon surface condition. At low strains, the value for U for aluminum single crystals was 4200 cal per mole ; however, this value decreased to 920 cal per mole when the specimens were polished during the test at a rate of 50 X 10-5 win-1 The activated volume also was found to increase with the rate of metal removal. That the surface plays an important role in plastic-deformation processes has been adequately demonstrated.1-4 Of particular interest at this time are the observations4 that the creep rate of single crystals of fee metals is increased markedly when specimens are polished during the deformation process. These observations were interpreted in terms of a dislocation debris layer at the surface regions of the crystal. This layer, which appears to be a region containing a high concentration of dislocations or segments of dislocations, not only will impede the egress of dislocations on the primary slip system, but will also provide a barrier against which dislocations may pile up. By this means, a stress which opposes the motion of dislocations will be generated. It is considered that this stress must be taken into account in any theory which describes the plastic-deformation process. Although a detailed dislocation model cannot be given at this time, it may be stated that the stresses opposing the motion of dislocations arise from the dislocations in the debris layer, Ts, and ti due to the resistance to motion imposed by internal obstacles such as Lomer-Cottrell barriers, subgrain and grain boundaries, forest dislocations, and so forth, as well as the resistance due to the presence of jogs on dislocations and the interaction of the stress fields of dislocations, and so forth. In essence, we have added an additional term, ts, to the usual form of the equation T = Ta- Tb, where Tb is the back stress due to the various types of obstacles which impede the motion of dislocation. Accordingly, the net stress, t, acting on a dislocation may be written as where Ta is the applied shear stress. For deformation which occurs by a thermally activated process5,8 ?=Ae-u/kT = A e(u,-VT)/kT [2] and U = Uo- Vt PI where U = activation energy for plastic flow, y = shear strain rate, Uo = activated energy for plastic deformation in the absence of stress and depends upon the particular deformation process, V = activated volume, k = Boltzmann constant, T = temperature, OK, and A = frequency factor. From Eqs. [I] and [3], U = Uo- V(Ta - Ti - TS) [4] and it is seen that if Ts decreases, the activation energy, U, must decrease if V remains constant. However, as will be shown, V is a function of the surface conditions. In their work on aluminum, Lytton and coworkers7 reported that at low strains the activation energy was 3400 cal per mole and at high strains it was 28,000 cal per mole. The lower value was interpreted in terms of the energy necessary to overcome the Peierls force, while the higher value was associated with the energy necessary for dislocations to move by a cross-slip process. It will be shown that the lower activation energy is associated with the surface debris layer rather than with the Peierls force. EXPERIMENTAL PROCEDURE Single crystals having a nominal cross section of 1/8 in. and a 3-in. gage length were prepared by a modified Bridgman technique using a multiple-cavity graphite mold. The initial purity of the metals was 99.997, 99.999, and 99.999 pet for aluminum, copper, and gold, respectively. The orientation of the specimens is given in Fig. 1. The measurement of the activation energy as a

Jan 1, 1964

By J. W. Rutter, K. T. Aust

The migration of individual, large-angle grain boundaries has been studied as a function of tempereature and solute concentration in specimens of zone i.e filled lead containig very small additions of silver and of gold. Tile results are compared with various the-ories of grain boundary migration and with observations made prev.iorlsly of grain boundary migration in similar specimens of zone-refined lead containing tin additions. A previous investigation by the authors dealt with [he temperature dependence of grain boundary migration in bicrystals of zone-refined lead containing small additions of tin.' It was shown that tin additions as low as a few parts per million cause a large decrease in the grain boundary migration rate at any given temperature, as well as a marked increase in the temperature dependence of the migration rate. It was found that existing theories of grain boundary migration. based on the motion of dislocations. or upon the concept of atom transfer in groups across the boundary (group process theory). or upon the control of grain boundary motion by volume diffusion of impurity atonls along with the boundary. are incapable of accounting for the observations. The single process theory of grain boundary migration. which is an absolute reaction rate calculation based on the transfer ui atoms singly across the moving boundary, was found to predict the migration rate reasonably well for a number of boundaries whose motion was shown to be very little influenced by impurities, but not for boundaries whose illation was influenced markedly by impurities. It was concluded that the elementary process of grain boundary migration involves the activation of single atoms during transfer across the boundary. and that inadequate knowledge is available to permit the influence of impurities to be properly taken into account. The present study was initiated to check the validity of the above conclusions with other alloy systems, namely high-purity lead with small additions of silver and of gold. Both silver and gold diffuse faster. and with a lower activation energy of volume diffusion. than does tin in lead;' consequently, a study of the effects of silver and gold on grain boundary migration in high-purity lead offered a means of testing theories of boundary migration based on bulk diffusion of the solute (eg. ref. 3). In addition. it was hoped that the present work, in comparison with the results for tin in lead, would provide information concerning which factors are important in determin- ing the interaction between solute atoms and a grain boundary. EXPERIMENTAL PROCEDURE The preparation of bicrystals of zone-refined lead, with various silver or gold additions, was identical to that previously described for the lead-tin alloys.''4 Each bicrystal consisted of a striated crystal which was grown from the melt. and an adjacent striation-free crystal which was introduced by artificial nucleation and growth.''4 The striation or lineage substructure in the melt-grown crystal provided the driving force for grain boundary migration. During the preparation of striated single crystals by growth from the melt, it was found that silver or gold concentrations as low as 2 or 3 ppm by atoms were sufficient to cause formation of the hexagonal cell structure. which is due to the presence of impurity, during freezing. This structure is revealed on the solid-liquid interface by decanting the liquid during freezing. The hexagonal cell structure was observed previously4 in zone-refined lead crystals with tin contents above approximately 200 ppm by atoms. These concentrations of silver, gold, or tin are in agreement with the predicted amounts required for cell formation in lead,5'6 under the present conditions of freezing.4 The absence of cell structure at decanted interfaces, therefore, served as a useful indication that the silver or gold contents were less than 2 or 3 ppm by atoms in the specimens as grown. It was found that grain boundary migration occurred only very slowly when the solute content approached that necessary for cell formation. As a result, the present experiments were conducted with silver or gold additions less than 1 ppm by atoms. This impurity level is well within the solid solubility limits for silver and gold in lead.7 The annealing treatments, measurements of grain boundary velocities, and orientation determinations were carried out as described previously.' However. each bicrystal was also chemically polished in a solution consisting of 8 parts glacial acetic acid and 2

Jan 1, 1961

By Knut L. Sandvik, Aage Solbakken

it is an established fact that the collecting properties of xanthates and anionic collectors are dependent on the hydrocarbon chain length. This is ascribed to the greater adsorption densities caused by increasing the xanthate chain length. As batch flotation tests showed similar trends for amines, an investigation of the adsorbing properties of amines was undertaken. Because earlier investigations showed adsorption densities for dodecylamine salts on quartz varying as much as 20 times under apparently similar conditions,1-4 it was decided to make a survey of the changes in adsorption density due to the drying conditions of the quartz. EXPERIMENTAL PROCEDURE The quartz, handpicked in the pegmatite quarries of Iveland, Setesdal, had the following composition: SiO2 99.81, A12O3 0.01, Fe2O3 0.05 and loss by ig-

Jan 1, 1969

By S. Yukawa, M. J. Sinott

The low solubility of bismuth in copper and its segregation at copper grain boundaries with resulting embrittlement is well known.1-3 The heterogeneous diffusion of liquid bismuth into polycrystalline copper has also been studied.4 This work presents some further observations on these phenomena using high-resolution auto radiography to detect the presence of bismuth in copper polycrystalline and bicrystal specimens. The auto radiographs were made by the stripping film technique which produces an autoradiograph that is intact with specimen surface and can be examined simultaneously with the under-lying microstructure. The details of the technique have been described previously.3 In one series of experiments, high-purity copper was alloyed with 0.02 to 0.03 wt pct radioactive bismuth obtained from the Oak Ridge National Laboratory. Melting and casting was done under a

Jan 1, 1960

By Ernest G. Enck

"The Rockets' Red Glare" of the Fourth of July is produced by strontium compounds. However, strontium has a number of less spectacular uses; i.e. in, or in connection with, the manufacture of ceramics, caustic soda, glass, railway and truck signal flares, beet sugar and steel. The principal ore of strontium for use both as the mineral and for production of compounds is celestite (SrSO4). This mineral varies in color from white to pink or blue depending on presence of impurities. It has a hardness of about 3.5 and specific gravity of 3.9. It is brittle and has perfect basal and prismatic cleavages. The high grade ore is obtained from England, hence it has become the standard for all other producing areas. (See analyses, Table 1.) The most objectionable impurity in English celestite is iron, coming mostly from adhering clay. On the other hand, Mexican celestite, while no higher in strontium sulfate content, is extremely low in iron (less than 0.2 pct), hence it is more desirable for certain uses. Most of the celestite in Spain and in the United States is high in calcium and barium, and commonly high in iron, and requires some form of beneficiation in order to be equal to English ore. The natural carbonate (SrCO3), or strontianite, is less important than celestite as a source of strontium, because it is less abundant and is not so widespread in its occurrence. Furthermore, it generally occurs with calcite (CaCO3) and lead sulfide (PbS), and for most uses these impurities are detrimental. This mineral is generally white or yellowish, forming needle-like crystals. It has a hardness of about 3.7 and a specific gravity of 3.68-3.8. The mineral is brittle and has an imperfect cleavage. A typical analysis of German strontianite is shown in Table 1. [ ] Distribution of Deposits UNITED STATES Occurrences of strontium minerals are known in Arkansas, Arizona, California, Illinois, Ohio, Pennsylvania, Tennessee, Texas, and Washington. Celestite occurs in the Vulture Mountains, Maricopa County, Arizona in beds three to ten feet thick associated with sandstone, gypsum, and barite. Because of the low strontium content, approximately 86 pct SrSO4, it has no commercial value. A large deposit of celestite occurs in San Bernardino County, California, in the Cady Mountains near Argus Station, about eight miles west of Ludlow. The celestite here is interbedded with shaly and clayey tuff in a zone about 300 ft thick. Massive, finely crystalline ore has been recovered with an analysis

Jan 1, 1960

By Michael B. Kahle, Fred J. Scheaffer

Production scheduling, along with production planning, provides projections of future mining progress and time requirements for the development and extraction of a resource. These schedules and plans are used by management as a means of attaining the following objectives (1) maintaining or maximizing expected profit, (2) determining future investment in mining, (3) optimizing return on investment, (4) evaluating alternative Investments, and (5) conserving and developing owned resources. The first four goals are generally concerned with mining costs, both capital and operating requirements, and as such, play an important role in production planning. However, this chapter is concerned with the fifth management objective of resource development in order to conserve and perpetuate the corporate entity. The following discussion is based on the premise that detailed economic evaluations and market surveys have been performed and analyzed and that the results indi¬cate a viable project.

Jan 1, 1979

By L. R. Velho, N. A. D. Parlee, J. Gani

THE unsteady-state type of gas-liquid metal diffusion cell1 has found considerable application.2"4 Cells of this general design can function as steady-state cells if allowed to operate long enough to reach steady state. This report tells of some success in the adaption of this type of cell for steady-state work, using the 0-Ag system in which the mass transfer of the gas "species" is basically controlled by diffusion in the liquid. The gas, e.g-., O2, is maintained in the cell tube'-3 at 1 atm pressure, Fig. 1, by buret and sensitive oil manometer. The gas, after diffusing through the stagnant metal, escapes at the annular metal surface around the tube at a lower constant partial pressure, in this case that of O2 in slowly flowing air, 1 atm.

Jan 1, 1970

By J. M. Dupouy, R. A. Rawe, M. B. Bever

The aging characteristics of a titanium alloy containing 13 pct V, I1 pct Cr, and 4 pct A1 have been investigated by hardness measurements, X-ray diffraction, and metallography. The P phase decomposes into 0 + a, and 0 + a, + TiCr, above about 1050°F; below this temperature a transition phase, believed to be w, precipitates first, followed by a, and TiCr,. The observed hardening is attributed to these reactions. Cold working of solution-treated specimens accelerates hardening and raises the hardness level attained. A TTT diagram is proposed. NEW titanium-base alloys, designated as "all-beta," have recently been developed. These alloys contain large amounts of P-stabilizing elements such as molybdenum, chromium, or vanadium. When cooled from the solution temperature, they consist only of P; in particular, the martensitic a,' phase does not form.

Jan 1, 1961

By John R. M. Hill, Gerald Zink, Fun-Den Wang

The work described in this paper is sponsored by the Bureau of Mines for the purpose of accelerating the drilling of roof bolt holes and reducing the quantity of materials needed to fill each hole. A high-speed, small-hole drill has been fabricated and tested in the laboratory. High Priority has been given to safety, reliability, and compatibility with underground coal mining practice. The combination of drag bits and erosion jets is designed for high penetration rate, long wear life, and uniform hole size in a variety of sedimentary strata. A reliable high-pressure, high-speed swivel feeds water to the bit at about 4 L/min (1 gpm). The duplex hydraulic intensifier which drives the jets has a 40-kW (30-hp) capacity. Results of recent full-scale laboratory testing (Now. 1977) are presented.

Jan 12, 1979

By Gilbert Thiessen

THE purposes of this paper are (1) to show that the mineral matter content of coal is satisfactorily represented by the Parr formula; that is, Mineral matter = 1.08 Ash + 0.55 Total sulfur (2) to compare ash-to-mineral-matter ratios with factors by which ash values must be multiplied in order that dry, factor-times-ash-free values shall equal Parr unit coal values; (3) to examine such ash-correction factors and to compare them with similar factors corresponding to certain simplifications or modifications of the Parr formulas and (4) to show that ash-correction factors used for simplification in calculating approximate unit coal calorific values cannot be. correctly used for the conversion of other determined values in an analysis to the unit coal basis, but that each type of calculation requires separate treatment in simplification.

Jan 1, 1934

By J. J. Marcus

Mineral industry decision-makers are frequently required to select between competing equipment. Various criteria and methods are currently being used, and this writer would like to suggest a method recently tested on two large power shovels in an open pit mine. An initial examination of both shovel A and shovel B indicated that the latter should give the best overall results. since: 1) It swings 13% faster; 2) it carries a dipper with 23%: greater capacity; 3) purchase price is 8.6% lower; 4) shovel weight is 12.5% greater; 5) it has considerably greater bail pull under most operating conditions; 6) the electric controls are of a more modern design. However, shovel B has half the service life. With these points in mind, shovel A was selected by The Buckingham Method, an operations research technique.

Jan 9, 1965

By Benny Langston, Frank M. Jr. Stephens

IN recent years much attention has been given to recovery, treatment, and disposal of dusts discharged into the atmosphere from operations of industry. Considerable data has been accumulated on both operational1-4 and design5,6 of dust-collector equipment for commercial installations. On the other hand, there is almost no published data on design and construction of small-scale equipment to handle dust problems that arise in the ore-dressing laboratory. Dust-collection equipment such as multiclones, single-cyclones, scrubbers, chemical and mechanical filters, settling chambers, and electrostatic separators has proved its efficiency for collecting dust in industry. In the laboratory, however, the engineer is faced with the problem of collecting small quantities of dust, inexpensively, without diverting the major effort from the metallurgical problem to the problem of collecting dust produced by the process.

Jan 8, 1954

By John Chipman

HE lecture on 'Thermodynamic Properties of Blast Furnace Slagso prepared in 1959 and published two years later required revision in one particular before it appeared in print. The activity of SiO, was deter mined through studies of the equilibrium: SiO, (in slag) 2C (graphite) = (in Fe) 2C0 (1 atm) The ratio for each experimental temperature was found from the heat of formation of cris-tobalite, the entropies and heat capacities of the re-actants, by virtue of the third law of thermodynamics. Discrepancies between several kinds of data led to investigations regarding other equilibria involving SiO, on the suspicion that there might be an error in the third-law value of its free energy. In particular the equilibrium: was restudied by Kay and Taylor who Confirmed the earlier results of Baird and Tayloron which their SiO, activities depended. The free energy of Sic was also rechecked4 independently. These and other equilibrium measurements led to the conclusion6 that the free energy of SiO, at high temperatures is in error and requires a correction of about -5 kcal. The exact source of the error is uncertain; it could lie either in the entropy of SiO, or in its heat of formation, but it more probably lies in the latter. Adjustment of this free energy lowers the ratio by a factor of approximately 4. Accordingly it will be necessary to multiply by this factor all of the SiO, activities determined by this method.',B Referring to the lecture cited, this correction should be applied in Figs. 8, 9, 10, 19, and 20. It applies also to the experimental data of Fig. 13, bringing these as well as those on the ternary system into good agreement with the work of Taylor and associates. At the same time it eliminates the discrepancy shown in Fig. 11, lowering both lines until the upper

Jan 1, 1962

By C. A. Eligwe, F. W. DeVries, A. E. Torma

This study is an investigation on using hydrogen peroxide for tank-leaching of uranium with sulfuric acid. The optimum sulfuric acid concentration was found to be 0.03 mole 11 -'for a 25% pulp density suspension. The order of reaction with respect to sulfuric acid concentration was found to be ns0.75. The best results vith hydrogen peroxide were obtained at a 4.64 molar ratio of 6202 to U in the ore. The order of reaction was found to be zero with respect to hydrogen peroxide concentration. The theoretical maximum rate effect of Hz02 on uranium extraction was derived as Vm = 8.15 x mole &-'min-'. The highest rate experimentally attained was 8.09 x mole kL'min-'. It was found that the uranium extrac- tion was not affected by the pulp density up to the 50% used in this study. However, the final yieldswere significantly higher (over 90%) for leaches carried out in the presence of Hz02 than (less than 90%) for leaches carried out in the absence of H202. The reaction was found to follow a first order course with respect to substrate concentration (pulp density) regardless of the presence of H202. The effect of temperature was more explicit at moderate tempetatures (30 to 55 C) than at lower (10 C) or at higher (70 C) temperatures. At this latter temperature an almost complete extraction was realized even without H202. The apparent activation energies were found to be AEa = 2.68 kJ mole-' in the absence of H202, 0.5 kJ mole-'with Hz02 at 40 C to 70 C. and 4.72 kJ mole-' with Hz02 at 10 C to 40 C. All these activation energy values suggested that the uranium extraction process is diffusion controlled regardless of the presence of H202. Further, the change in activation energy in the presence of Hz02 indicates the possibility of change in the reaction mechanisms at lower and higher temperatures.

Jan 1, 1980

By Hans Strack

Electroluminescence of GaAs p-n junctions fabricated by simultaneous diffusion of sulfur and iron was investigated at 77°K. A narrow emission peak with a half width of about 4 kT in the energy range between 1.14 and 1.155 eu was attributed to iron. Other transition elements exhibited light emission in the vicinity of the iron peak, namely nickel between 1.15 and 1.16 ev and cobalt between 1.16 and 1.17 ev. The efficiency of the doping with iron depended on the amoz~nt of arsenic present. A weight ratio of arsenic to iron of 4:l was sufficient to observe the emission lines associated with transition elements. The presence of oxygen reduces the intensity of the light emission. In addition to the levels associated with transition elements, levels at 1.05 and 1.28 ev, probably due to lattice defects, are observed except in diodes fabricated in solution-grown GaAs. THE near band edge emission of GaAsp-n junctions has been studied extensively in the past.' GaAs devices utilizing spontaneous and stimulated near band edge emission are of considerable practical importance. Typical junctions are fabricated by diffusion of a heavily doped p region into degenerate n-type GaAs. Much less work has been done on investigating the radiative recombination via deep levels in lightly doped p-type material. This area is of interest in understanding the performance of GaAs n-p-n transistors. GaAs transistors show remarkable improvement in high-frequency performance and current-gain stability at high temperatures, when iron is added to sulfur during the emitter diffusion process. The present work was initiated to investigate deep-level electroluminescence of iron-doped GaAs p-n junctions fabricated on vapor-phase epitaxial GaAs and on solution-grown GaAs. For comparison several diodes doped with cobalt and nickel were studied. Iron, cobalt, and nickel have an electron configuration of the type

Jan 1, 1968

By William E. Ford, Edward Salisbury Dana

A. Hexagonal Division 1. Normal Class (13) Beryl Type 2. Hemimorphic Class (14) Zincite Type 3. Pyramidal Class (15) Apatite Type 4. Pyramidal-Hemimorphic Class (16) Nephelite Type 5. Trapezohedral Class (17) B. Trigonal or Rhombohedral Division 1. Trigonal Class (18) Benitoite Type 2. Rhombohedral Class (19) Calcite Type 3. Rhombohedral-Hemimorphic Class (20) Tourmaline Type 4. Trirhombohedral Class (21) Phenacite Type 5. Trapezohedral Class (22) Quartz Type 6. Other Classes (23) 7. Other Classes (24) Mathematical Relations of the Hexagonal System 119. The HEXAGONAL SYSTEM includes all the forms which are referred to four axes, three equal horizontal axes in a common plane intersecting at angles of 60") and a fourth, vertical axis, at right angles to them. Two sections are here included, each embracing a number of distinct classes related among themselves. They are called the Hexagonal Division and the Trigonal (or Rhombohedral) Division. The symmetry of the former, about the vertical axis, belongs to the hexagonal type, that of the latter to the trigonal type. Miller (1852) referred all the forms of the hexagonal system to three equal axes parallel to the faces of the fundamental rhombohedron, and hence intersecting at equal angles, not 90". This method (further explained in Art. 169) had the disadvantage of failing to bring out the relationship between the normal hexagonal and tetragonal types, both characterized by a principal axis of symmetry, which (on the system adopted in this book) is the vertical crystallo raphic axis. It further gave different symbols to faces which are crystallographally identical. It is more natural to employ the three rhombohedra1 axes for tri- gonal forms only, as done by Groth (1905), who includes these groups in a Trigonal Syslem; but this also has some disadvantages. The indices commonly used in describing hexagonal forms are known as the Miller-Bravais indices, since the were adopted by Bravais for use with the four axes from the scheme used by Miller in the other crystal systems.

Jan 1, 1922

ADVANTAGES OF LIFE MEMBERSHIP The Institute calls the attention of members to the following advantages of obtaining life membership: 1. One payment avoids the trouble of future payments. 2. The interest on $150 is less than the annual dues. 3. Provision is thus made early in life for the less productive years. 4. In case of in increase of clues at any time in the future life members are exempt from increased payments. Excerpt from, By-Laws. Article III. Section 3 Any Member or Associate not in arrears may become, by the payment of one hundred and fifty dollars at one time, a Life Member or Life Associate, and shall not be liable thereafter to pay annual dues. The money thus received shall be invested and only the income thereof used for current expenses of the Institute.

Jan 1, 1916

(Under this heading will be published notes sent to the Secretary of the Institute by members or other persons. ) Position in sales department is open for a mining engineer with experience in mine ventilation and possessing some knowledge of fan design; one competent to lay out ventilating systems to meet various conditions. No. 2. A large company manufacturing mining machinery has an opening in one of its Western agencies for a young mechanical engineer who has had some experience in designing along general machine shop lines, and who is familiar with cost systems. No. 3. A large university desires to secure a prominent metallurgist for a vacant professorship in metallurgy. No. 4. Opening at a mine in New Jersey for a technical graduate to begin work as chairman on the surveying squad. Salary $50 per month to start. No. 5.

Jan 11, 1913