Search Documents

By E. A. Gulbransen, W. S. Wysong

THE behavior of molybdenum and its surface oxides in oxidizing and reducing gas atmospheres and in high vacua at elevated temperatures is a question of scientific and technical importance The use of molybdenum as a metal or as an important component in alloys in oxidizing atmospheres at elevated temperatures has been limited because of the unprotective nature of its oxide film and the volatility of this oxide at moderate temperatures. This communication will present results of a vacuum microbalance study 1,2 of the following problems. (11) the oxidation kinetics in the temperature range of 250° to 450°C; (2) the reduction with pure hydrogen of thin oxide films formed on molybdenum; (3) the volatility of the thin oxide films, and (4) the vacuum oxidation of molybdenum at high temperatures. Molybdenum is an interesting metal to study for the following reasons: (I) although the oxide-to-metal-volume ratio is greater than one, the metal is not considered protective; (2) the metal oxidizes readily at temperatures of 250°C and higher; (3) the oxides of the metal are reduced at temperatures as low as 500°C by pure hydrogen; (4) the oxide MoO3 melts at 795°C; and (5) the oxides of molybdenum are volatile at moderate temperatures. The following variables are studied in the oxidation kinetics. time, temperature, pressure, surface preparation, surface area, concentration of inert gas in the lattice, cycling procedures in temperature, vacuum effect and high temperature vacuum oxidation The general interpretation of many of these factors has been previously discussed. LITERATURE The oxidation of molybdenum has not been studied critically. Although" many studies have probably been made on the kinetics of the oxidation process, none has been reported in the literature available to us. The crystal structures found in the oxidation of molybdenum have been studied by Hickman and Culbransen 4 Their results showed that MoO2 is the oxide which is stable in contact with the metallic subgtrate throughout the temperature range 300 to 700°C. As the film thickens in the low temperature range, MoO3 becomes predominant on the surface. Above 400°C, Mo03 is no longer observed, Mo02 being the only oxide found. Hagg and Magneli5 have shown from an X ray study that the a-phase, orthorhombic MoO3 is stable up to 1050°C. Two other phases, ß and ß', with compositions close to Mo02 90 are also obtained The formula for the ß phase is not given but that of the ß' phase is defined as Mo9026. The ß' phase is found to be built upon a monoclinic unit cell. A -?-phase is isolated from a preparation M00275 heated for 17 hrs at 670°C. This phase is

Jan 1, 1947

By George S. Barnett

The Equis and El Roble projects are located in the Cordillera Occidental of Colombia. The Equis vein deposits have sulfide ore reserves of 95,955 mt (105,770 st) grading 8.51 g/mt (0.248 oz/st) gold and 12.4 g/mt (0.36 oz/st) silver with 0.94 % copper, 1.10 % lead and 11.06 % zinc. Ore reserves at El Roble are estimated as 1.1 Mmt (1.21 million st) grading 4.89 % copper and 3.39 g/mt (0.099 oz/st) gold. Geologically possible reserves at Equis may total 1.6 Mmt (1.76 million st). El Roble has the potential to contain several tens of millions of metric tons. Exploration included diamond drilling, trenching, channel sampling, rock and soil geochemistry, geophysics and tunneling. Erratic high grade samples affect the weighting of channel and drill core samples. Secondary reconcentration of gold is also a factor. Sample maps and graphs show the distribution of values to be highly variable. Geostatistical treatment of some of these data gave important guidelines for parameters such as sampling densities, drill hole spacing and confidence limits.

Jan 1, 1985

Utah Engineering Experiment Station, University of Utah, Salt Lake City, Utah. D. A Lyon, Director. Important work on ore dressing has been carried out at this station Before listing the Technical Papers and Bulletins available, it is well to point out especially that Technical Paper 1, Flotation fundamentals, 4, Flotation fundamentals (pt 2), and 5, Flotation fundamentals, pt 3, are out of print and can only be consulted at libraries or elsewhere. The Technical Papers and Bulletins available are as follows: Technical Paper 6, Recovery of zinc from ferrite compounds in the electrolytic zinc process, 25 cents; 7, Flotation fundamentals (pt 4), 40 cents; 8, The technique of preparing thin sections of rock, 75 cents; 9, Flotation fundamentals (pt. 5) 30 cents; 10, A new development in the preparation of briquetted mineral grains, 15 cents, 12, A method for the determination of cadmium in mill and smelter products, 25 cents; Bulletin 10 (revised 1931), Mine sampling and the commercial value of ores, 35 cents, 14, Report of research investigations (1922-23), with papers on these subjects Hydrometallurgy of zinc, Flotation experiments on Utah sulphur ore, Oil shale investigations, Zinc oxide investigations, 25 cents;

Jan 1, 1933

Bureau of Mineral and Topographic Survey, University of Kentucky, Lexington, Ky. Arthur C. McFarlan, State Geologist The Kentucky Geological Survey was abolished by a recent legislative act and the Bureau of Mineral and Topographic Survey at the University of Kentucky was created in its place Publications of the former Survey are distributed by the present Bureau Several series of papers and volumes have been issued but only those of Series 3, 4 and 6 are now to be had in whole or in part Of Series 4, (1912-18) only one group of papers is available Vol: 1, pt. 2, Miscellaneous papers on fire clays, limestones and coals of parts of the state (1913), $125. Of Series 3 (1904-1912), the following bulletins are pertinent and may be had. Bulletin 3, Coals, clays, etc., of Kentucky (1905), 50 cents, 14, Coals of the Pineville Gap region (1912), $1.25, 16, The Waverlain formation of east central Kentucky (1912), 50 cents, 17, Coals of the Tradewater region (1912), 50 cents, 18, Coals of Quicksand region (1912), 50 cents; 19, Geology and coals of the Central City, Madisonville, Calhoun, and Newberg Quadrangles (1912), 50 cents

Jan 1, 1933

AUGUST began with a reminder that warfare was still in progress in the world, in that the Greeks, still at war with Turkey, threatened Constantinople in spite of the small British and French forces of occupation and opened a vista of international dangers. There was in this, moreover, a recollection that religious questions in India had prevented the British from permitting a real settlement of the Turkish question, wherein the absence of Russia as a great power is missed. Civil warfare also continued in Ireland and China. Even in the military way the world is far from being at peace. Bloody fighting between the Fascisti (anti-communists) and the com-munists in Italy led to several provinces being put under martial law, but after a while these disturbances were quelled. In the latter part of the month the assassination of Michael Collins in Ireland produced a great shock. From China, however, there came rather favorable news, indicating the early reintegration of that country, which sooner or later ought to play an important part in world affairs. Economically, instead of there being any improve-ment, there grew a clearer perception of how bad things really are. Italian politics were in chaos through inability to find anyone to accept the premiership and assume the all but hopeless task of averting national bankruptcy. The French, too, began to see their own position in true colors, and especially to see how in reconstruction they had incurred debts on the strength of what they hoped to collect from Germany, with at last the understanding that the Germans could not pay and that France herself was thereby put in a desper-ate economic position. As for the Germans, them-selves their Reichsbank defaulted on ordinary bills early in August. As the month wore on the value of marks fell more and more and at the end it appeared that Germany was on the verge of economic collapse. On Aug. 7, another international conference (with America again absent) was assembled in London, this being the thirteenth since the war, and there was a general feeling that it would be the last. The prime question was what is to be done about the German reparations, but underlying was the whole subject of the entente. The conference opened like a meeting of importunate creditors, doubtful whether the debtor had any tangible assets. On Aug. 14 this conference broke up without coming to any useful conclusion. Indeed, the acrimony among the premiers was so sharp that even the entente between Great Britain and France was endangered. The international situation was saved only by the Reparations Commission excusing the Germans from the payment of 50,000,000 gold marks that come due on Aug. 15 But although the entente was nominally preserved there is no longer any illusion about the interests of Great Britain and France being different and that henceforth they will play their own hands. The London conference was really an effort to maintain the partnership, and it failed.

Jan 9, 1922

The University of North Dakota, State Geological Survey, Grand Forks, N. D A G. Leonard, State Geologist. Two publications of the State Geological Survey are of interest Fourth Biennial Report, The clays and clay industries of North Dakota, and Bulletin 4, Lignite deposits and lignite industries of North Dakota. Bulletin 11 of the University is of interest: Geology and natural resources of North Dakota For further information, address the above

Jan 1, 1933

By H. A. Bedworth

ALLOYS of copper and silicon have been known for one hundred years or more but the commercial development of this type of alloy has taken place during the past few years. In 1905, Sperry1 proposed the use of copper-silicon alloys for springs and other purposes for which copper-tin bronzes were used. Some attention was given to this proposal at the time but no one succeeded in producing a practical alloy containing more than a fraction of a per cent. of silicon. The equilibrium relations of the copper-silicon system were studied first by Rudolfi2 and later by Sanfourche3 and Corson.4 The constitution of the system has also been recently investigated by Matuyama,5 and in the laboratories of the American Brass Co. by Smith.6 Some of the physical properties of the copper-silicon alloys have been investigated by Norbury7 and by Geiss and Van Liempt.8 Summarizing the results of various investigators of, the constitution of copper-silicon alloys, the solubility reaches its maximum value, 6.7 per cent. silicon, between 721° and 782° C. At 852° C. the solubility is 5.25 per cent., while at 400° C. it is only 4.1 percent. silicon. The copper-silicon alloy begins to get so hard at about 3 per cent. silicon that it is difficult to manage. It was found by Jacobs that the addition of manganese to this alloy considerably improved the working

Jan 1, 1929

By F. F. Lines

IT is not the intention of the writer to enter into a discussion of the relative merits of the duplex process as compared with the straight scrap and pig iron process, working under the same conditions, but rather to present in a general way several modifications of the former process, and then describe the method adopted by the Maryland Steel Co., as best suited to local conditions, and also to meet the metallurgical problem presented in the removal from the iron of an unusual constituent-chromium. The principal factors to be considered in deciding whether or not duplexing should be employed are: (1) Chemical constituents of pig iron. (2) Variety and quantity of steel to be produced. (3) Relative cost of pig iron and scrap. (4) Regularity of operation. (5) Capital to be invested. (6) An existing Bessemer plant. Having decided to adopt the duplex process, several combinations may be used, viz.: (1) Acid-lined converter with basic open hearth. (2) Acid-lined converter with electric furnace. (3) Basic-lined converter with basic open hearth. (4) Basic-lined converter with electric furnace. (5) Basic open hearth with electric furnace. The combination of an acid-lined converter with a basic open-hearth furnace is the one most commonly employed, and as it is the one best adapted to the conditions encountered at the plant of the Maryland Steel Co., we will briefly outline the advantages and disadvantages of the different methods of working.

Jan 4, 1915

By H. M. Dess, S. R. Bolin

A modifiedl Czochralski technique has been utilized to grow single crystals of YVO, pure or doped with europium or neodymium, from 1 to 2 in. long and 4 to 1/2 in. in dianz. An oxyhydrog-en gas-fired furftace zuas used in this ulork, and melts were contained in iridium crucibles. Successful application of the Czochralski ~vzethod was found to depend upon atmosphere control to prevent crusting and to limit melt decomposition, the establishment of symmetrical thermal gradients in the melt to obtain stable growth, and the selection of high-quality single-crystal seeds to prevent propagation of misorientations during growth and subsequent catastrophic cracking. The suitability of YVO4 as a host for laser-active trivalent rare earth ions has long been recognized. However, the problems associated with the growth of sufficiently large, good-quality single crystals have, until quite recently, seriously hindered satisfactory evaluation of the laser potentialities of this material. Both flux growth and Czochralski growth techniques were investigated at an early stage of interest in YVO,. The former method proved incapable of yielding crystals large enough for practical use,ly2 and the latter was beset with difficulties which took some considerable time to understand and overcome. Recently, however, the Czochralski growth process for YVO, has been improved along separate but similar lines of development by groups working independently in the Crystal Products Department of Union Carbide's Electronics Division and Bell Telephone Laboratories3 so that now good-quality single crystals of satisfactory size can be produced on a routine basis. Stimulated emission from a neodymium-doped YVO4 crystal grown by the Crystal Products Department of Union Carbide was obtained by O'connor4 of MIT, Lincoln Labs. An oxyhydrogen gas-fired furnace was used in this work, Fig. 1, and melts were contained in iridium crucibles. The starting material was 99.9 to 99.99 pct pure YVO4 powder purchased from the Chemical and Metallurgical Division of the Sylvania Electric Products Co. Typical impurity levels, determined by spectrographic analyses, were as follows: Si, 50 to 500 ppm Al, Fe, Mg, 5 to 50 ppm Ni, Pb, Mo, Mn, Ce, Cs, 1 to 10 ppm Initially, YV04 powders predoped with neodymium or europium were obtained from Sylvania. Later, however, because of a desire to grow a series of crystals containing relatively broad concentration ranges of these dopants, it proved more convenient to start with pure YV04 and mechanically admix Nd2O3 or Eu@~ powders plus equimolar amounts of V2O5. The empty crucibles were preheated to 1900" to 1950oC, a temperature range where melting occurred readily. The powdered YVO4 feedstock was then added incrementally. However, a marked tendency toward

Jan 1, 1968

By A. J. Opinsky

THE purpose of this note is to indicate the locations and sizes of various interstitial holes in the orthorhombic uranium lattice based on a hard-sphere model. First, plane configurations of three and four atoms will be examined, and then the true interstices surrounded by four atoms in space and by five atoms in space will be obtained. The data and notation contained in a report by Tucker' will be used. Plane Configurations Fig. 1 presents the orthorhombic uranium lattice made of spheres touching at the closest interatomic distance. The three light-colored spheres in the ab plane are illustrative of the first type of configuration to be examined. If one edge of the unit cell is taken as the origin, the three atoms can be represented by the vectors [Oi + Oj + Ok], [ai + Oj + Ok] and [(a/2)i + (b/2)j + Ok] where i, j, and k are respectively parallel to a, b, and c. In the future, this notation will be shortened to [000], [a00] and [a/2 b/2 0], respectively. A vector R = [r s t] de-scribes the position of the hole surrounded by the atoms. Since the center of the hole must be equidistant from the three atoms R2 = r2 + s2 + t2 = (r-a)2 + s2 + t2 = (r-a/2)2 + (s-b/2)2 + t2. R = [a/2 (b/4) - (a2/4b) 0] is the solution of these

Jan 1, 1955

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

By W. H. Geis

The following pages summarize the causes that led to the suggestion of unit operation of the paloma field, the organization of com-mittees, preparation of the Paloma Operators Agreement and the reasons for rejection of the plan. Introduction Long ago an Austrian physicist observed that under certain conditions the condensation of a liquid from gaseous mixtures resulted from pressure reduction. Some 50 years later he would have known that his research was not in vain. He would have seen a group of serious operators and engineers seeking to apply that principle to a conservation . program for unitized production in the Paloma gas field—but he would also have been saddened to see that forces unsympathetic to the application of science in oil production, with little or no appreciation of modern methods and the advantages of cooperation, so far have prevented the adoption of that program. Soon after the Paloma field was discovered it was realized that all the hydrocarbons in the reservoir existed in the gaseous phase. This condition was confirmed over a large area. Therefore, if the field was to be properly exploited with the greatest ultimate recovery of condensate, the hydrocarbons in the reservoir must be produced in the single or gas phase. They must be cautiously extracted with the least possible reduction of the natural pressure. If this could be accomplished, or if artificial pressure control were utilized, the condensation and underground loss of the valuable distillate would be preventable—otherwise it would not be. Wholehearted cooperation of all oper-ators was required in order to accomplish the conservation purposes of the program. To this end the production engineers of the several companies concerned lent their time and talents. They fully investigated the physical relationships of the products within the complicated gaseous mixture, prepared extensive reports on the subject and drew up a reasonably efficient plan of operations, which now is commonly called the "Paloma Unit Plan" but actually was entitled "The Paloma Operators Agreement." All of the engineers were not in perfect agreement on all the features of the plan, or even on all the engineering principles. However, it is safe to say that on all the important or essential factors there was a unanimity of opinion, particularly as to the objectives. These were fairly simple and reduce to one controlling item, "pressure control" by cycling or recycling. Organization The principal operators initiated the program by calling a meeting of all the lessees in the area, at which an organization was perfected, known as the "Paloma Operators Committee." Various subcommittees were appointed to expedite the work, including an "Engineering Committee." These func-tioned in a businesslike manner, frequently reported to the superior committee and

Jan 1, 1942

The figures given here were received through the courtesy of the Bataafsche Petroleum Maatschappij and the Standard-Vacuum. There is an increase in production for the year of approximately 4½ million barrels. In November the average production indicated that during the year 1935 the total production would probably exceed 50 rnillion barrels. To maintain this production, only 106 wells were drilled during the year, mainly in South Sumatra.

Jan 1, 1935

By V. V. Clark

WHEN a district is more or less primitive, and a trained mining engineer attempts single- handed to prospect it according to old standards, he generally fails. He has not the ability to live out in the open alone for months at a time and carry on with enthusiasm and determination like the old-time prospector. But the same engineer, placed in an organized group where modern prospecting methods are employed, is immediately put on his mettle and his chances of winning are greatly increased. Marsman Investments, Ltd., with headquarters in Manila, has at the present time, Sept. 4, 1937, six prospecting parties in the Netherland East Indies. Three of these groups are combing their assignments for lode mines, studying structures, developing and reaching out into veins and zones with diamond drills. The other three are searching for placer mines with pans, pits, and Empire drills. I am in charge of one group seeking commercial gold placers on the Island of

Jan 1, 1937

By V. Kondic, W. M. Rumball

HUNT and Jackson' have recently suggested that binary eutectics might be classified according to the entropy of fusion of the component phases. Such a classification was in fact proposed2 some time ago by the authors and the purpose of this communication is to present some supporting evidence. As pointed out by Hunt and Jackson' typical metals of low entropy of fusion, ?S, tend to form normal eutectics (using Scheil's terminology3). Where one phase is metallic (low ?S) and the other nonmetallic (high AS) then anomalous structures are formed. These anomalous structures may either be regular (e.g., Bi-Sn)or irregular (e.g., A1-Si). Finally Hunt and Jackson suggest that where both phases are of high ?S regular faceted structures are formed. In the proposed classification2 the ratio of the entropies of fusion is taken as the quantitative parameter, i.e., ?Sa/?SB = E, where e > 1.0. An extensive literature survey has been carried out2,4 for reliable photomicrographs of eutectic structures. The structures, numbering 151, have been classified into two classes, viz., normal (i.e., lamellar and rodlike) and anomalous. The latter group has been arbitrarily subdivided into regular and irregular anomalous eutectics. Details and sources of the structures are given elsewhere.2,4 In the absence of better thermodynamic data the value of E has been determined for each of the systems making the following assumptions and approximations: l) The entropy of fusion of solid solutions may be calculated additively;5 ii) Inter metallic compounds are treated similarly but with the addition of the following term for fully ordered structures.5 -4.573(Ni lOg10 Nl + N2 log10 N2) where Nl and N2 are the atomic fractions. It might be argued that the entropies of fusion are meaningless as the eutectic phases form at some temperature (T,°K) below their true melting point (Ta or Tb). As AS, = Lo/To if La the latent heat of fusion of a, is assumed independent of temperature, the actual entropy change AS& is given by La/Te. The ratio of entropies of fusion then becomes Fig. 1 shows E' plotted against cumulative totals for normal and anomalous systems from which it is seen that normal eutectics predominate at low values of E'; e.g., some 90 pct of normal systems lie below E' = 1.5 with 65 pct of anomalous systems above this value. Fig. 1 also shows that the regular anomalous structures occur mostly at low values of c' possibly suggesting growth more akin to normal than anomalous growth. The choice of c as a classification parameter was based on nucleation concepts, it being observed that metals widely separated in Sundquist and Mondolfo's8 nucleation series were anomalous and those close together normal. The basis of these classification views is really outside the intended scope of this communication but it is hoped to explain them fully in the near future.7 Having arrived at this entropy of fusion classification by nucleation considerations it is interesting to note that Hunt and Jackson's ideas are based on growth considerations. Elsewhere one of the authors4 has shown that an even better classification of the metallographic structures reviewed is obtained from purely conventional heterogeneous nucleation concepts. It has been found that systems having a value of the parameter +b less than 0.28 are almost certainly normal and above this anomalous: V, is the gram atomic volume. This parameter is nevertheless closely related to c and c', these being an approximation of p. The parameter is also related to the other classification3,8,9 which have met with any success in the past. All these classifications are to be reviewed shortly by the authorsU7 A significant thing about the classifications based on

Jan 1, 1968

By Michael Hoch, Walter C. Wyder

The isothermul section of the Nb-Ti-Zr-O system at 1500°C was investigated using X-ray dzffraction and metallographic techniques. UP to 66.7 at. pct 0, the system contains nine four-phase regions. Tsopleths at 10, 20, 30, 40, 50, and 55 at. pct 0 weye constructed. The purpose of this investigation was to determine the general shape of the quaternary equilibrium phase diagram of niobium, titanium, zirconium, and oxygen at 1500°C. The system was truncated at 66.7 at. pct. O., PREVIOUS INVESTIGATIONS The Ti-Zr-O system was investigated in this laboratory.' The binary systems of interest have been compiled and discussed by anssen2 and Levin, McMurdie, and Ha11. Elliott4 has determined the Nb-O system by metallographic and X-ray diffraction techniques. He shows the existence of three oxides, namely NbO, NbO2, and Nb2O5. At 1500°C the solubility of oxygen in niobium is about 4 at. pct. No solid solubility region is shown for either NbO or NbO2. EQUIPMENT The same equipment as that for the study of the Ti-Zr-O system was used. The X-ray diffraction patterns were analyzed with the help of the ASTM card set5 and NBS circulars.6 MATERIALS The niobium powder (99 pct pure), the titanium powder (99.6 pct pure), the niobium pentoxide, and the zirconium dioxide used in this study were purchased from the Fairmount Chemical Co., Newark, N.J. The zirconium powder (99.4 pct pure) was obtained from the Charles Hardy Co., Inc., N.Y. Reagent-grade titanium dioxide was purchased from the Matheson Co., Inc., Norwood, Ohio. The oxides were dried in air at 700°C for 24 hr before use. Though the materials used were not "hyper-pure," the impurities present do not affect the results (lattice parameters, phase boundaries), within the experimental accuracy. PROCEDURE Samples of the desired compositions were made up, in mole pct, from the materials listed above. In some cases the intermediate binary compounds, such as NbO and TiZrO4 were prepared beforehand and used in the preparation of the samples. This technique enabled equilibrium to be reached from two sides. The components of each sample were mechanically mixed in a mortar and pestle and pressed into 3/16-in. diam pellets. The pressures used in compacting were of the order of 50 to 100 x 103 psi. Sintering was accomplished by heating the samples in a tungsten crucible (3/4-in. high, %-in. diam, 1/8-in. wall, lid with XB-in. hole). The pellets were separated from each other and from the crucible by means of small spiral coils of tungsten wire placed between the stacked pellets and on the bottom of the crucible. The sintering time was from 4 to 12 hr at 1500°C under a vacuum of 6 x 101-5 to 1 x 10-6 mm of Hg. All samples were reground after the first or second heating repressed, and reheated. In most cases: equilibrium was obtained after the first heating, as the X-ray diffraction pictures after each heating remained unchanged. Quenching of the samples from 1500°C was at first only possible by allowing the crucible and its contents to lose heat by radiation. The temperature dropped from 1500° to 900°c in approximately 1 1/2 min, which was considered adequate when compared to the times used by other investigators to reach equilibrium in the temperature range of 1000°c and lower. Later, a new technique for faster quenching of the samples was cleveloped. This technique involved the removal of the samples from the crucible, whereupon they were quenched by coming in contact with the water-cooled copper base of the furnace. This manipulation was performed without breaking the vacuum. The sample pellets were placed on a tungsten wire rack inside the crucible. The wire rack passed through the hole in the crucible lid, where it was connected to a small nonmagnetic chain. The chain was fed to the side of the furnace by means of a brass rack which fitted between the body and lid of the furnace. Suspended at the end of the chain, near the furnace wall, were three magnetic washers. With the use of a strong

Jan 1, 1962

By AIME AIME

COMMITTEES. LOCAL COMMITTEE.-R. C. Crawford, Chairman; Harrison W. Craver, Secretary; Julian Kennedy, Taylor Allderdice, E. W. Pargny, Charles L. Miller, W. H. Rea, S. A. Taylor, M. E. Wadsworth, W. A1. Henderon, A. C. Dinkey, W. L, Jones, E. L. Messier, George Mesta, J. H. Jones, G. H. Riley, S. L. Goodale, D. W. McNaugher. LADIES' COMMITTEE.-Mrs. Taylor Allderdice, Chairman; Mrs. Julian Kennedy, Mr. R. C. Crawford, Mrs. E. M. Herr, Airs. J. W. Marsh, Mrs. T. A. Mellon, Mrs. G. P. Bassett, Jr., Airs. D. M. Clemson, Mr. Charles L. Miller, Mrs. V. L. P. Shriver, Mrs. W. A. Bostwick, Mrs. A. C.. Dinkey, Mrs. A. P. Childs, Jr., Mrs. F. R. Dravo, Mrs. Hermon Griffin, Mrs. W. H. Nimmick, Mrs. F. H. Lloyd, Mrs. S. G. Cooper, Mrs. S. H. Church, Mrs. E. N. Ohl. The Institute Headquarters was established at the Hotel Schenley, where a bureau of information was maintained for the benefit of the visiting members and guests of the party during the time of the meeting. TECHNICAL SESSIONS. The first session, held Tuesday evening, Mar. 1, 1910, in the large lecture hall of the Carnegie Institute, was called to order by Harrison W. Craver, Secretary of the Local Committee. Mr. Craver introduced Dr. John A. Brashear, who extended to the members and guests a hearty welcome to the city of Pittsburg, to which David W. Brunton, President of the Institute, responded. The following papers were presented in oral abstract by the authors: Biographical Notice of Dr. Charles B. Dudley, by Dr. R. W. Raymond, New York, N. Y. Biographical Notice of William Metcalf, by Col. II. P. Bope, Pittsburg, Pa. Development of Hindered Settling Apparatus, by Robert H. Richards, Boston, Mass. (Illustrated by lantern-slides.) A Few Mining Districts in the Argentine Republic, South America, by Z. S. Beyl. (Illustrated by lantern. slides.)

Apr 1, 1910

By P. S. Kotval

THE nominal composition of "hconel" alloy 718 is 53 pct Ni-19 pct Cr-19 pct Fe-3 pct Mo-5 pct Cb-0.8 pct Ti-0.6 pct A1-0.05 pct C. The nature of the fine strengthening phase in this alloy has been open to debate. iseelstein' has identified the strengthening phase in the matrix of "Inconel" alloy 718 as a colum-bium-rich fcc y' precipitate. Wagner and Hall2 have noted that the metastable y' precipitate overages to an orthorhombic Ni3Cb precipitate which manifests itself as an acicular phase. These authors thus clarify Kaufman and Palty's earlier suggestion3 that the strengthening phase is orthorhombic NisCb. Wagner and Hall's review also reports work by cometto4 which suggests that the fine strengthening phase is not fcc / but bct with a Ni3V type structure and based on the Ni3Cb composition. Kir man and warringtons have shown by analysis of electron diffraction patterns that the metastable strengthening phase in a 55 pct Ni-15 pct 0-25 pct Fe-5 pct Cb alloy is bct and based on the Ni3Cb composition. Raymond~ has provided electron diffraction evidence which indicates that "y'" in "Inconel" alloy 718 is bct in structure. This note presents unambiguous data on the structure of the strengthening phase in "Inconel" alloy 718* ihe samples of this alloy were provided by courtesy of the ASTM task group on phase identification in 'superalloys. after prolonged aging. The electron diffraction patterns presented show that strengthening phase is not y' but bct as was proposed by cometto,' supported by Raymond,~ and identified by Kirman and warringtons in a similar system. Fig. 1 shows a selected-area diffraction pattern taken from a thin foil of "Inconel" alloy 718. The sample had received a final aging treatment of 1118 hr at 1200°F to precipitate the strengthening phase in the matrix. Fig. 2 is a schematic representation of the features in the diffraction pattern. The matrix orientation is (0i2)~,, as is shown by the indexed zone in Fig. 3. Figs. 4, 5, and 6 illustrate that the pattern, Fig. 1, is composed of three bct zones, viz., (0i4), (2i0), and (i01), respectively. These three zones correspond, respectively, to the alignment of the c axis of the bct unit cell with the [001], [loo], and [OlO] directions of the fcc matrix and serve to illustrate the fully coherent relationship of the precipitate structure with the matrix. The streaking of certain reflections is also consistent with the above orientation relationship. The interpretation of the diffraction effects presented here shows the metastable strengthening precipitate in "Inconel" 718 alloy to be bct in structure and demonstrates that it is not an ordered fcc y' phase.

Jan 1, 1969

By John Fritz

Gentlemen of the American Institute of Mining Engineers : I desire to thank you sincerely for the distinguished honor you have conferred upon me by electing me to the presidency of this society, a position which in the past has been filled by some of our most distinguished and ablest members, men eminently qualified by education, practical training and a business ability which has enabled them not only to fill the position with credit to themselves, but as well with honor to the society. In deference to a custom long established, by which the presidentelect is expected to read a paper on some subject with which he is more or less familiar, I have thought that a brief review of the methods employed in the manufacture of iron, as witnessed by myself, and reaching back to 1838, would interest some of our older members and give our younger ones a glimpse into the trials and difficulties encountered in those early days by the pioneers in this great industry. In 1840, 12 to 20 tons of pig-iron was the make of a furnace per week—at this time from 1200 to 2000 gross tons. In 1840, 3 to 4 tons No. 4 wire rods per turn. They have lately made 176 gross tons in 11 hours. In 1840 I have not the quantity of puddled iron made; but it was

Jan 1, 1895

By J. E. Coyne, L. E. Tanner, J. E. Boyd

In recent investigations of the isothermal transformations of the retained 0 phase in a titanium alloy having 13 pct V, 11 pct Cr, and 3 to 4 pct Al, there have been indications that the w transition phase is the initial decomposition product at temperatures below about 950°C (510 c).' This metastable phase, found in a number of titanium-base alloys rich in stabilizing elements and known to have an adverse effect on their ductility and toughness, is not easily observed by the usual experimental techniques. Since wis coherent with the /3 matrix,495 distinct interphase boundaries are not revealed metallographically. However, in some cases, an etching effect (i-e., a "mottled" /3 surface) poorly resolved by light microscopy has been found to correspond with the presence of w.6 X-ray diffraction examination has generally been the most suc- cessful means for identifying this phase and crys-tallographic determinations have been made.4'5 Dynamic elastic modulus7 and electrical resistivity measurementse have also aided in the identification of w. In the current study, the electron microscope was utilized to examine microstructures in aged Ti-13V-11Cr-3A1 that were unresolvable by light microscopy techniques. Using negative parlodion replicas (shadowed with chromium at 27 1/2 deg) examination was made of various transformation

Jan 1, 1962