Search Documents

By J. H. Frye, C. P. Sun

A PRIMARY substitutional solid solution is a solution that has the same crystalline structure as the solvent metal, and in which solute atoms have replaced solvent atoms at random on the host lattice. This replacement usually results in an increase in hardness as measured by conventional penetration tests. The factors controlling this hardness increase have been investigated in some detail for copper and silver aneys.1-5 It has been shown that at least, four factors are involved: (I) concentration of solute, (2) row of the periodic table from which the solute is taken, (3) increase in lattice parameter of the solvent produced by the solute, and (4) work-hardening produced by penetration of the hardness indenter.2,4 The last factor is of the utmost importance. An investigation of the available data2.4 leads to the conclusion that the solutes that produce large hardness increases in copper or silver do so principally because they increase the rate of work-hardening. Furthermore, it is doubtful whether any solute produces appreciable hardening in the absence of plastic deformation and hence work-hardening. Thus it is clear that an understanding of the effect of solutes on rate of work hardening is essential to an understanding of the hardness of solid solutions. This effect of solutes is also important in forming operations such as rolling or deep drawing. The presence of elements that confer rapid rates of work-hardening will increase power consumption and may well decrease the amount of deformation possible between anneals. This paper is the report of an investigation of the factors that control rates of work-hardening in copper and silver solid solutions. The silver and copper alloys considered are those in which all solutes are from the B subgroups or second short period of the periodic table. Experience with hardness, with structure of alloys, and with electrical conductivity has proved that results of a fundamental nature are most likely to be obtained if alloys are made up on the basis of the positions of the constituent elements in the periodic table. In previous work, Meyer analysis data on high-purity copper and silver solid solutions were obtained through careful measurements with fully calibrated equipment and these data were corrected to correspond to a standard grain size. From these corrected Meyer analysis data rates of work-hardening have now been calculated. CALCULATION OF RATES OF WORK- HARDENING The Meyer analyses, on which this study of rates of work-hardening is based, consisted in determining impression

Jan 1, 1944

By Geoffrey Gilbert

The Montana Phosphate Products Co., subsidiary of the Consolidated Mining and Smelting Company of Canada, operates three phosphate properties north and northeast of Garrison, Powell County, Mont. Production of all three is from the same phosphate bed, a 3 to 4-ft. member of the Phosphoria formation, whose outcrop is traceable across the mountains of the Garnet Range in a series of southeasterly pitching folds. Because of topographical differences and of variations in the attitude of the bed, each property has its own mining methods and problems. Most of the phosphate rock produced since 1930 has been shipped to the plant of the Consolidated Mining and Smelting Co. at Trail, B.C., where it is treated with sulphuric acid for conversion to phosphoric acid, which in turn is used to produce various fertilizers. History The occurrence of rock phosphate in Montana has been known since 1910, and the Garrison area was mapped by the United States Geological Survey in 1913. In the nineteen twenties William Anderson, owner of a ranch 8 miles north of Garrison, discovered phosphate on his land, and the Montana Phosphate Co., which later became the Montana Phosphate Products Co., was formed to work the deposit. Montana Phosphate Products Co. later obtained United States leases on two adjoining parcels of ground, and this combined property, known as the Anderson mine, has been the main source of Con-solidated's phosphate rock. The mine now includes an adjoining parcel leased from Anaconda and mined from the Anderson workings. In 1940, the Graveley mine, a small privately owned property 6 miles east of the Anderson, was leased from the owner by Montana Phosphate Products Co., and a U. S. lease held by Graveley on some adjoining ground was subleased. In 1943 the Luke mine, on the Mineral Hill property, 1 3/4 miles south-southwest of the Graveley, a U. S. lease, which previously had produced a few thousand tons, was optioned from the lessees by Montana Phosphate Products Co., and is now being developed. At both these mines the rock is appreciably higher grade than at the Anderson mine. Geology The Phosphoria formation is the Permian member of an extensive sequence of Paleozoic and Mesozoic rocks. It is underlain by Pennsylvanian (Quadrant) quartzite and Mississippian limestone, and overlain without any marked unconformity by Jurassic (Ellis) shale and Cretaceous shale and sandstone. In the Garrison area, the Phosphoria itself consists mainly of about 50 ft. of gray to yellow chert. Immediately below the chert is the phosphate, usually 3 to 4 ft. thick. Below the phosphate occur a few

Jan 1, 1948

By G. F. Comstock

These notes should be considered as a further discussion of Mr. S. W. Miller's paper on "Some Structures in Steel Fusion Welds."l In that paper and the resulting discussion, several conflicting opinions were expressed as to the identity of the needles or small crystals present in oxyacetylene and electric welds. An interesting specimen of an electric weld examined by the writer seems to afford new evidence regarding the needles, that may be worth presenting at this time. The specimen consisted of a piece of 3/8-in. (9.5-mm.) steel plate, about 21/4 by 13/4 in. (5.7 by 4.5 cm.) in size, on which some iron had been deposited by arc-welding to a depth of about 3/16 in. (4.7 mm.). The weld appeared to be a very good one, with no noticeable break or boundary between the plate and the deposited iron. Sections for microscopic examination were cut in three planes at right angles to each other through the deposited metal, two of these sections also extended through the steel base. After polishing in the usual way, the microscope showed that the deposited metal was full of very small, round, gray, oxide spots, while the steel plate contained quite a number of alumina inclusions and a little slag. The sections were etched with nitric acid in ordinary alcohol, and structures similar to those described by Mr. Miller were then displayed. Fig. 1 shows the typical appearance of the deposited metal, which was quite uniform in all three of the planes examined. The round dark-gray spots are oxides, and the pale angular crystals are evidently what Mr. Miller called cem-entite and Mr. Jeffries martensite, while Mr. Ruder and Professor Boyls-ton think that they might be nitride. The boundary between this structure and the steel base was sharply defined under the microscope. Fig. 2 shows the structure of the plate just under the weld; this is almost martensitic and resembles a coarse-grained casting. This coarse cast structure soon became finer as the distance from the weld increased, finally becoming very fine, with numerous small particles of sorbite. This very fine structure, shown in Pig. 3, became coarser in turn and finally merged into the original normal structure of the steel plate, shown

Jan 1, 1920

By H. J. Engell, W. Frank, A. Seeger

SWISHER and ~urkdogan' have determined the solubility of oxygen in a iron. They found it to lie between 7 and 10.5 at.-ppm at 881°C. Using earlier work on the permeability of oxygen in bcc iron,' they arrived at the following expression for the diffusion coefficient of oxygen in bcc iron (k = Boltzmann's constant, T = absolute temperature): where The present authors3 have estimated the activation energy QD for the diffusion of oxygen in bcc iron in two different ways from various experimental data.2'4"6 In the first method QD + QS (QS = heat of solution for oxygen in bcc iron in thermodynamic equilibrium with solid FeO) was determined either from data on the reduction of FeO with hydrogen4 or from measurements of the internal oxidation of silicon in a iron.5 Using an estimate of QS from investigations of the oxygen solubility in 6 iron2 (in thermodynamic equilibrium with molten FeO) Q = 0.97 ev or Q~ = 1.06 ev were obtained. From the magnitude of these values it was concluded that oxygen migrates interstitially in bcc iron and that consequently the activation energy QD for diffusion of oxygen has to be identified with the migration energy E~ of the oxygen atoms. Therefore, for a second estimate of QD from the diffusion coefficient of oxygen in 6 iron at 1450" ~,~ we used the theoretical expression:3 (a = length of elementary cube edge, m = mass of interstitially diffusing atom, sM = migration entropy), applicable to diffusion via the octahedral interstices in bcc lattices. Taking sM = 3.8 k (migration entropy of carbon in a iron), one gets Q = 0.90 ev. Hence, in Ref. 3 Q = (0.98 *0.1) ev was proposed as a plausible value for the diffusion energy of oxygen in bcc iron. sM + 9 (9 = solution entropy for oxygen in bcc iron) can be determined from permeability measurements.4 Using the above-mentioned estimate for QS , the following expression for the solubility c (atomic concentration) of oxygen (in thermodynamic equilibrium with solid FeO) in bcc iron was derived: From [4] the solubility of oxygen at 881°C in a iron is calculated to lie between 0.6 and 12 at.-ppm. We see that the solubility determined by Swisher and

Jan 1, 1969

By J. B. Goddard

The discovery of rhenium on the ion exchange resin used at the uraniun in-situ leach operations at Palangana, TX, led to a laborabory study of possible recovery methods. Rhenium was present in small amounts in the ammonium carbonate leach liquors as the perrhenate anion, ReO4-. It concentrated on the anion exchange resin, which was a factor of 10 more selective for rhenium than for uranium. Various elution systems were investigated for stripping the rhenium from the columns after the uranium had been eluted with chloride or nitrate solutions. Although the per-chlorate ion was most efficient on a molar basis, nitrate ion combined the benefits of efficiency and low cost. A 3N or stronger concentration of nitrate containing up to 0. 5N H + was found to be the system of choice. A rhenium sulfide concentrate containing up to 14010 Re was obtained from these effluents by hydrogen sulfide precipitation. Preliminary experiments were run to produce rhenium metal powder by oxidation of the concentrate to NH4ReO4 followed by hydrogen reduction at elevated temperature.

Jan 1, 1984

ALEXANDER, JOHN S, M,'74-6,'81-3 ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

ALEXANDER, JOHN S, M,'74-6,'81-3 *ASHBURNER, C A, M, '85-7 ASMUS, GEORGE, Dl, '78-80 BACON, D H , M, '00-2 BAYLES, JAMES C , M,'80-2,'91-3 P, '84-5, V,'88-9 BIRKINBINE, JOHN, M, '83-5, V, 'S7-J, P, '91-2 BLAIR, THOMAS S , M, '74-43 BLAKE, WILLIAM P , V,'71-4,'76-7,'05-6 *BLANDY, JOHN F, V,'71-3,'78-9 BLOW, A A, C, '05-7 BOWIE, A J , JR, V,'93-4 *BRAMWELL, J H , A1, '89-91 BROOKS, THOS B , M, '72 BRUNTON, D W , V, 97-8 BUCK, STUART M , M, '83-5 *BURDEN, JAMES A, V,'80-1 BURNHAM, WILLIAM, M, '82-4. CAMPBELL, H H, M, '93-5 CHAMBERLAIN, H S , V, '96-7 CHANNING, J PARKE, V,'08 CHRISTY, S B , V. '91-2, '07-8 CHURCH, JOHN A, M, '79-8l,'94-6, V, '07-8 COGSWELL, W B, V, '74-5,'86-7

Jan 1, 1910

By R. F. Hehemann, S. T. Zegler

The w phase in zirconium alloys containing more than G pct Nb can form in a difjUsionless manner during quenching or with composition change during aging at temperatures below 550°C. The latter treatment establishes a metastable equilibrium between an w phase containing 5 pct Nb and a ß phase containing 45 pct Nb. The superconducting transition temperat~ire of quenched Z?-10 pct Nb and Zr-15 pct Nb alloys is increased by aging at 375°C and both alloys exhibit the same Tc after prolonged aging. The superconducting transition both in the quenched and in the aged alloys is relatively sharp (occurring ovev a temperature range of <0.5°K), and is interpreted in terms of the microstructure that characterizes the ß-w) mixture and proximity effects postulated for thin-film superconductors. At elevated temperatures alloys of the transition elements from groups 4 to 6 in the periodic table exhibit wide ranges of mutual solubility in the bcc structure. Except for compositions that are high in a group 4 element? the bcc structure can be retained at room temperature by quenching and several systematic studies of the influence of composition on superconductivity in bcc alloys have been reported.&apos;&apos;2 The high-temperature bcc form (ß) of the group 4 elements—titanium, zirconium, hafnium—is not retained upon quenching but instead transforms marten-sitically to the hcp structure (a). The Ms temperature can be lowered by alloying the group 4 metals with a solute from a higher group and with a critical amount of solute the martensitic transformation can be suppressed. The 3 phase, however, is not retained without modification. Rather, a metastable phase, w (in particular in titanium- and zirconium-base alloys), occurs over a fairly wide range of compositions above that required for suppression of the martensitic transformation.3,4 As in the formation of a, the transformation of ß to w occurs in a diffusionless manner during quenching and the temperature for its initiation (ws) is lowered by increasing solute content. The ws temperature can be well below room temperature and reversibility of the transformation allows w that forms on cooling to low temperatures to disappear again when the sample is returned to room temperature.5 In Zr-Nb alloys the w phase can also be formed during aging at temperatures below 550°c.5 In this treatment, a metastable equilibrium is established between a niobium-rich ß phase and a zirconium-rich w phase. The present study of Zr-Nb alloys was undertaken to examine the influence of microstructure: as controlled by composition and heat treatment, on the superconducting transition temperature, Tc. MATERIALS AND PROCEDURE The alloys were prepared from zirconium crystal bar that was spectrochemically pure except for 30 ppm of Al, 40 ppm of Cu, 100 ppm of Fe, and 1 ppm of each B and Pb. The niobium used was 99.5+ pct pure containing according to the suppliers&apos; (Stauffer Chemical Co.) analysis a maximum of 50 ppmO, 60 ppm of N, 30 ppm of C, 5 ppm of H, 200 ppm of Ta, 50 ppm of Mo, and 15 ppm each of Fe, Co, and Ni. The alloys were prepared in the form of buttons weighing approximately 4 g by arc melting on a water-cooled copper hearth in an inert-gas atmosphere. All alloys were heat-treated in the ß-phase region for 3 days at 1000°C and water-quenched. For heat treatment, the specimens, 0.5 cm in diam by 1.0 cm long, were wrapped in zirconium foil and sealed in an inert-gas atmosphere inside quartz capsules. Quenching was done by breaking the capsules under water. Subsequent aging treatments of Zr-10 pct Nb and Zr-15 pct Nb alloys were done by placing the specimens in a lead bath at 375°C and quenching in chilled brine. The phases present in the quenched and aged alloys were identified by optical and X-ray metallography. X-ray powder patterns were taken at room temperature with a 114.6-mm-diam Debye-Scherrer camera and CuK-a radiation. Superconducting transition temperatures were determined from magnetic-permeability measurements6 in a 10 oe field. The superconducting transition temperature was determined from a plot of galvanometric deflection as a function of temperature by extrapolation of the linear portion of the curve to zero deflection. In Figs. 1 and 3 the arrows indicate the temperature range of the transitions. RESULTS AND DISCUSSION Superconductivity in Quenched Alloys. In Fig. 1 Tc for alloys quenched from 1000°C is plotted against nominal composition. Indicated also in Fig. 1 are results of metallographic studies. Alloys containing less than 5 pct Nb transform martensitically to a during quenching from 1000°C and Fig. 1 demonstrates that Tc increases significantly as the niobium concentration in a is increased. On the basis of the Bardeen-Cooper-Schreiffer theory of superconductivity7 it seems most likely that this increase in Tc results from an increase in the density of electronic states as zirconium is alloyed with niobium. This increased density of states has been revealed clearly in low-temperature specific-heat measurements.8 The martensitic transformation to a is suppressed when the alloy content exceeds 5 pct Nb. In the range from approximately 6 to 30 pct Nb, quenched alloys consist of a mixture of B and w phases and the amount

Jan 1, 1967

By N. J. Grant, B. C. Giessen, Paul Predecki

ALLOYS of gold, silver, and aluminum with elements of the groups BII, BIII, BIV, and BV were prepared by a rapid quenching technique (splat) and were examined by X-ray diffraction. Five new intermediate phases were found and will be described briefly herein. For the gold and silver systems, the concentration ranges having an electron/atom ratio e/a of 1.4 to 1.5 ("3/2 Hume-Rothery phases") were studied primarily. Master alloys were prepared from high-purity metals (99.9+ pct or better) by melting either in evacuated fused silica capsules or by nonconsum-able-electrode arc melting in an argon atmosphere. Small pieces, 20 to 50 mg, of each alloy were blast-atomized to form a splat, by a technique similar to that described by Duwez and Willens.1 The technique used for this study is described in detail in Ref. 2; it utilizes a resistance-heated graphite crucible with a small hole at the bottom, directed toward a metal substrate or quenching plate. The prepared alloy rests over the fine hole, through which it is expelled by an explosion shock wave in the form of fine droplets (1 to 50 µ) of molten metal onto a copper or silver substrate, which is maintained at about -190°C. The resulting very high cooling rates (see Ref. 2 for quantitative measurements) can prevent the process of nuclea-tion and growth in many instances, resulting in the formation of metastable phases. The splat particles were transferred to a GE-XRD5 diffractometer and maintained at -190°C, where they were examined with CuKa radiation. The samples were then allowed to warm to room temperature or were heated to higher temperatures until the equilibrium structures formed. Of fifteen alloy systems considered, nonequi-librium structures were encountered in six; these are described below and summarized in Table I. In the system Au-Sb a metastable £ phase (A3 type, hcp, a = 2.898 + 0.002A; c = 4.731 * 0.004A; c/a = 1.633) was found in the concentration range Au + 13 to 15 at. pct Sb. This phase is isomorphous with the stable phases in the systems Au-Cd, Au-In, and Au-Sn, all at an average e/a ratio of 1.4 to 1.5. The concentration range of one-phase metastable was deduced from the small amounts of supersaturated gold solid-solution phase present in the splat product. It was found that ? could also be retained by splatting onto a substrate held at room temperature: however, decomposed into the equilibrium phases Au + AuSb2 after heating to 200°C for 1/2 hr, or on holding the powdered splatted alloy at 20°C for several months. Calorimetric measurements will be made in an attempt to decide the question whether ? is metastable at all temperatures or whether it is a stable phase at low temperatures. There is evidence that another phase, possibly also close-packed but with a different stacking sequence, can be obtained by rapid quenching of alloys with a different antimony content. Klement, Willens, and Duwez3 reported the existence of an amorphous phase on quenching Au-Si alloys (25 at. pct Si) to - 196°C. They found that on heating to room temperature another phase of unknown crystal structure was formed. This was confirmed (see Table I); however, the new crystalline phase, designated as ?, could also be formed simply by rapid quenching to room temperature, and even was found to exist already in the as-cast Au + 20 at. pct Si alloy. It was found that ? decomposed into Au + Si on the specimen surface at room temperature. This behavior, and the question whether or not there is an equilibrium-temperature region for ?, have not yet been resolved. It is probable that ? (Au + 20 to 21 at. pct Si) is cubic of the -brass type (D81-3) with a = 9.60, + 0.01A and N = 52 atoms per cell [compare 6 (CU-Sn)4]. Except for two very weak lines, the powder pattern of about thirty lines could be indexed on this basis; however, a determination of the atom positions has not yet been attempted. For Au-Ge the C phase was observed at about 21 at. pct Ge as reported by Luo et at.5 Lattice parameters a = 2.876A, c = 4.73,A, c/a = 1.64 were found. In the Au-Pb system, formation of a ? phase was not observed, but in the lead-rich region at 75 at. pct Pb, broad peaks belonging to an amorphous phase were found. The maximum diffracted intensity occurred at 28 = 32.4 deg which is about 1 deg larger than the position of the (111) line of lead (Cuka). For Ag-Pb, an amorphous phase analogous to the one found in the Au-Pb system was observed; this metastable phase exists probably at about 75 at. pct Pb. Since no lead-rich alloys were tested, all alloys consisted of silver + amorphous phase at -190°C. In A1-Ge alloys, line-rich and complex powder patterns were obtained at about 30 at. pct Ge; they bear similarities to those of aluminum and germanium, but are of lower symmetry; the existence of more than one intermediate phase is possible. The authors are grateful to the Kennecott Copper Corp. for Fellowship support, and ARPA (Contract

Jan 1, 1965

By B. B. Rath, Hsun Hu

Rates of migration of large-angle boundaries have been studied in zone-refined aluminum crystals, defonned 80 pct by rolling in the (110)[112] orientation at -78°C followed by a recovery anneal at 80°C. Artificially nucleated grains show a marked variation. by an order of magnitude, in their growth rates in different directions. The average activation energy for the migration of all boundaries was found to be about 16,000 cal per mole. The anisotropy of the boundary migration is rationalized on the basis of the boundary structure. It has been observed by Beck and HU,1 Kohara el al,2,3 and Czjzek and Haessner4 that recrystallized grains formed upon annealing Of deformed sing1e crystals of aluminum show anisotropic growth characteristics. Kohara et al. found that single crystals rolled in the (110)[112] orientation, when random nuclei were provided on one side of the crystal by rubbing with emery paper and annealing, developed a sharp recrys-tallization texture on the other side of the crystal upon further annealing. This sharp recrystallization texture consisted of four components, which were related to the deformation texture of the crystal, i.e. (110)[112], by rotations of ±40 deg around each of the two common [ 111] axes&apos; They also noted that recrystallized grains were elongated in directions perpendicular to either of these two common [1111 axes. They attributed this anisotropic growth to the difference in the rate of self-diffusion or diffusion of impurity atoms along the tilt and the twist boundaries. A somewhat similar investigation was conducted by Czjzek and Haessner4 On strained single-crystal sheets Of alum- inum. These authors claimed that the matrix structure of the deformed crystal had a greater effect on the growth anisotropy of the recrystallized grains than did the boundary orientation itself. In the present investigation quantitative measurements of the rate of grain boundary migration in anisotropic growth have been made in zone-refined aluminum (99.9999+pct pure) crystals deformed 80 pct by rolling in the (110) 112] orientation. Crystals of this particular orientation were chosen because of the following desirable features: 1) the crystal does not change its orientation during rolling; 2) the rolling plane contains all the significant crystallographic directions; and 3) when annealed, following deformation, the crystal does not re-crystallize spontaneously but polygonizes to a stable and homogeneous structure. Hence, the initial orientation of the crystal and a constant strain energy in the matrix can be maintained during subsequent grain boundary migration studies. It is essential to keep the driving force constant for the study of boundary mobility.5 EXPERIMENTAL PROCEDURE A cylindrical single crystal of 1 in. diam was grown by the Bridgman method in a high-purity graphite mold. The resistance ratio, R(4.2°K) /R(298°K) , of the grown crystal was approximately 2.0 x 10-4. A number of slices, 1/4 in. thick, were cut from the crystal along the (110) plane and were mechanically and electrolyti-cally polished to remove the strained surface layer. The crystals were then rolled along the [112] direction to 80 pct reduction in thickness at -78°C. To minimize surface friction, the crystals were rolled between two layers of 0.005-in. teflon sheet. Rolling was interrupted, prior to completion, to remove the surface layers and the edges by electropolishing. These and similar precautions in handling the rolled crystals

Jan 1, 1967

By Wing L. Lew

LEAD, silver, and zinc, in quantities of economic importance are found in the Aguilar ore. The lead occurs as galena and the zinc as sphalerite and marmatite. The silver occurrence is more complex. Pyrargyrite and proustite have been identified only occasionally. Galena is silver-bearing and so are the various other sulphides, though to a lesser degree. The principal nonsulphide gangue minerals include calcite, quartz, wollastonite, rhodonite, and various calcium, aluminum, and iron silicates. A typical analysis of, the ore is: Pb, 11.2; Zn, 12.3; Fe, 4.4; Mn, 2.2; Cu, 0.15; S, 11.2; CaO. 7.6; "Insoluble," 50.1 percent; and Ag 263 g per ton. Crushing is done in three stages. The primary crusher at the mine is set to deliver about a 5-in. product. The crushed ore is then transported to the secondary crushing plant by a 3-km cableway where the general practice is to hold the product of the first Symons to about 1 in., and of the second Symons to about 1/2 in. When the ore is soft and rich the product of the first Symons is by-passed directly to the ball-mill bins. Dust control in the secondary crushing plant is effected by enclosing the dust-emanating sources and exhausting the enclosures with a Clarage No. 18 fan driven at 1300 rpm by a 20-hp motor. Use is also made of spray water at one or two critical places. Every effort is made to keep the air free from visible dust. Dust counts taken at the working places show dust concentrations of less than six million particles ner cu ft. The composition

Jan 1, 1947

By J. F. K. Brown, E. E. Roecker

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By E. E. Roecker, J. F. K. Brown

For three years The Hudson Coal Co. has used egg anthracite instead of coke in its foundry cupola. It has long passed the stage of being told it cannot be done—the metal would be cold, of poor quality, or the speed of operation would be low. From observation, from use and from test. we know that our metal is about average; the cast iron invokes no adverse comment from the machine shop and the speed suits our foundry requirements. We have there-iore resolved into practice anthracite combustion processes in an industrial furnace formerly using coke, under conditions suitable to our needs. When it comes to translating what we know into use in another cupola, however, where operating conditions may be different, or to explaining why, with seemingly the same conditions in our own cupola, we have attained sometimes a temperature of 2800° in the metal and at another time 2600°, or a speed of 5 tons per hour against 2 35 tons per hour, we cannot do it. We cannot do this because there seems to be an unbridged gap between laboratory ideas on combustion and practical ideas on com-bustiqn, which we have been unable to cross in terms understandable to us as practical consumers. This gap or bridge centers around the problem of how combustion actually takes place; and we believe it is controlled by two factors: (I) the character of the surface of the fuel and (2) the space provided and needed within which the oxygen of the air is allowed to or can act on that surface. It has long been contended on behalf of coke that porosity is an important factor in combustion, although, admittedly, there are two schools of opposing thought on this question, as revealed in technical literature. It has been understood generally that a light, porous coke is the best metallurgical fuel because there are more square inches of carbon exposed to the blast of air, therefore more useful carbon-dioxide reactions can take place in the given space between the entrance of the air and the point where useful work is done. It is now our general idea that the heavier and the harder the coal, the better the metallurgical fuel, provided the surface of that fuel is suitable for fast reaction with the oxygen. Time and Space A cupola is loaded in layers of fuel and iron. The horizontal line where the first charge of iron rests on the coal is the top of the bed coal. With us that is 22 in., usually, above the tuyeres where the air enters. This means 600 lb. of coal. Every subsequent coal layer is 100 to 125 lb. of coal, and that 100 to 125 lb. of coal melts 1000 lb. of iron at around 2700° in the ladle. This quantity of coal represents a 3-in. layer spread across the cupola. The question arises: If this 3 in. of coal will melt 1000 lb. of metal, why was it necessary to use 600 lb., or 22 in., of coal beneath and between the first charge of iron and the air entrance?

Jan 1, 1944

By Walter C. Holmes

IN the recently published book entitled "Man in a Chemical World," by A. Cressy Morrison, the several pages discussing explosives were included in the chapter on "Serving Industry." Such a classification is entirely correct, as blasting explosives function only as a tool for accomplishing certain useful work, a tool which is completely destroyed in one use. Explosives are so important to industry and to modern society, in fact, that it seems impossible to imagine the existence of civilized nations without access to commercial explosives as ready servants. Two main types of explosives are now in use, the low-velocity or deflagrating type, such as black powder, which is adapted for use in coal mining and other applications where a slow, heaving effect is desired, and high explosives of the dynamite type,

Jan 1, 1938

By L. E. PORTNER

INCREASING military demands on the petroleum industry have brought into bold relief the crude-oil reserves now available to meet combined military and civilian demands, emphasizing the necessity for a greater efficiency in recovery from what has been discovered than ever before, particularly in light of the absence of new discoveries. This situation-and the fact that the industry, as well as members of the Government charged with governing oil production, desire to meet all crude-oil demands made of the industry with the least loss in tangible reserves through production practices-paves the way for increasing application of sound principles of production engineering and conservation.

Jan 1, 1944

By S. C. Lindsay, D. J. I. Evans

With each year that passes hydrometallurgical processes are being more widely used to recover base metals from ores and concentrates. Generally these processes involve liquid-solid separation of metal-bearing liquors from barren residues. This may be done by countercurrent decantation, thickening and filtration, or filtration or centrifuging only. Choice of method is governed by chemical and physical characteristics of the pulps; cost of labor, power, materials, and waste disposal; and even by the amount of capital available when building plans are under way. Since all these controlling factors change with time and location and with technological advances, the separation method must be re-evaluated when new plants or expansion programs are contemplated. At the Sherritt Gordon refinery in Fort Saskatchewan, Alberta, an ammonia pressure leaching process recovers nickel, copper, and cobalt from the nickel concentrate produced at Lynn Lake, Manitoba.&apos; Pregnant liquors are separated from the barren leach residues in a thickener-filter liquid-solids circuit. The decision to use this type of separation was based on a summation of economic factors during the pilot plant and design stages. Although countercurrent decantation was not incorporated in the refinery flowsheet, the problems solved in thickening the leach residues and the experience gained in operating the commercial plant are pertinent to countercurrent decantation, particularly where it is applied to slow-settling leach slurries or slurries having a relatively high vapor pressure of a valuable, obnoxious, or poisonous vapor. The nickel sulfide concentrate is leached under pressure with air and ammonia to dissolve the nickel, copper, and cobalt and most of the sulfur, leaving a residue of iron and siliceous material to be discarded.2,3 During a subsequent distillation stage to recirculate part of the ammonia used for leaching, copper is recovered from the solution as a high-grade sulfide. After further purification to remove traces of copper and undesirable sulfur compounds, the nickel is precipitated by hydrogen under pressure at an elevated temperature. The cobalt, together with unreduced nickel, is precipitated as a mixed metal sulfide by hydrogen sulfide for eventual cobalt recovery. The end solution is then evaporated to produce a crystalline ammonium sulfate byproduct. As shown in Fig. 1, the nickel concentrate is leached in a continuous, two-stage, countercurrent circuit. In the first stage, or adjustment leach, the fresh concentrate is partially leached (60 pct) in the liquor produced in the second stage, or final leach. This system is necessary to produce a solution suitable for treatment in the copper sulfide precipitation step. Both stages are carried out at 170" to 180°F under a total pressure, with air, of 100 to 120 psig in large, horizontal, water-cooled autoclaves. The autoclaves are divided by overflow weirs into four compartments to give a certain amount of staging during leaching. In each compartment a relatively slow-speed (100 to 150 rpm) agitator maintains the nickel concentrate in suspension. Adjustment leaching, carried out in two autoclaves in parallel, is followed by a thickener-filter liquid-solids separation. Final leaching is done in two parallel trains of three autoclaves using aqueous ammonia to extract metal values from the adjustment leach residues. This too is followed by a thickener-filter circuit. Here the residues are repulped once with aqueous ammonia and twice with process water and refiltered after each repulping stage, to insure a maximum recovery of soluble metal, before being discarded to the tailings pond. The adjustment leach is followed by a seven-disk Dorr-Oliver American filter, with an agitator in the filter boot to keep the residues in suspension. Agitators have also been installed beneath the four ten-disk filters following the final leach thickener. Slurry Characteristics: A typical analysis of the Lynn Lake nickel concentrate, produced by differential flotation,&apos; is given in Table I. The concentrate comprises 35 to 49 pct pentlandite, (Fe, Ni)S; 3 to 6 pct chalcopyrite, CuFeS,; 1 to 4 pct pyrite, FeS2; and 24 to 42 pct pyrrhotite, Fe1-2S (where x varies between 0 and 0.2) together with various siliceous minerals such as actinolite, hornblende, and talc. During leaching, the sulfur in the pentlandite, chalcopyrite, and part of the pyrrhotite is successively oxidized through the thiosulfate and poly-thionate radicals to sulfate and sulfamate." Simultaneously the nickel, copper, and cobalt are converted to soluble ammine complexes and the iron in the pentlandite, chalcopyrite, and part of the pyrrhotite is oxidized to a spongy hydrated iron oxide. The hydrated iron oxide is readily broken down by the agitation needed to sustain the concentrate in suspension and to maintain a satisfactory mass transfer of the oxygen from the air to the slurry. Table I shows typical chemical, screen, and

Jan 1, 1961

By Roger B. Alke

INTRODUCTION Request to Mine Beneath Bridge The Jakes Run Bridge is a reinforced Portland concrete arch filled bridge located on WV Route 7 near Pentress, WV. The bridge has a span of 22.9 m (meters) and a height of 4 m above normal pool elevation to the underside of the center of the arch (See Fig 1). The bridge is a two lane structure with a width of 6.86 m. The structure is over 50 years old having been built in 1929 and is owned by the Department (WV Department of Highways). [ ]

Jan 1, 1984

By George S. Rice

MECHANIZATION in coal mining is a phrase which has attracted world-wide attention, and those persons not engaged on the practical side of coal-mine operations seem to regard mechanization as a panacea for many difficulties of the industry. The term "mechanization" as now employed by experienced mining men is restricted to mean mechanical loading of coal at the face. In a broader sense mechanization in coal mining was begun nearly half a century ago with the introduction of compressed-air undercutting machines and locomotives and, later, of electrically operated locomotives, undercutting and shearing machines, and drills. The use of coal-cutting machines, which has increased until now about three- fourths of the bituminous coal produced is being mechanically cut, first displaced hand-picking except in a few long-wall mines, and later gradually displaced the dangerous and coal-smashing method of blasting-off- the-solid.

Jan 1, 1929

By A. M. Sarem, J. M. Campbell

Molecular refraction is introduced as a new and improved third parameter for prediction of the PVT behavior of hydrocarbon systems. This parameter, characterizing the complex as well as the pure hydrocarbon systems (1) is a direct measure of London dispersion forces which affect the PVT behavior; (2) can be measured directly, accurately and easily for complex as well as pure hydrocarbon systems; (3) varies significantly between the reference substances thus allowing accurate interpolation of PVT properties; and (4) has a fundamentally sound basis. Molal average molecular refraction was used with the pseudocritical mixing rule proposed by Leland and Mueller to predict the molal volume of liquid and vapor for 84 published data points on nC4-nCI0, Cl-nC5, Cl-nC4-nC10 systems in the region of coexisting vapor-liquid and at the critical point. The same technique was applied to predict the densities of liquid hydrocarbon mixtures in the two-phase and single-phase regions near the critical point for seven different systems each having different properties of the heptanes-plus fraction, but all simulating the fluids of either gas-condensate or volatile oil reservoirs. A modification of the Leland-Mueller mixing rule for the determination of pseudocritical properties is also presented which yields more accurate liquid density predictions than the original form when used with the proposed third parameter. INTRODUCTION The PVT behavior of multicomponent systems has received widespread attention in the literature in recent years. A large portion of the reported work has stemmed from attempts to overcome the inherent difficulties encountered when using the standard compressibility-factor chart which shows 2 as a function of reduced temperature T, and and reduced pressure p,. This chart assumes that z, is constant for all systems. The error in this assumption is not pronounced for pipeline-type gases high in methane and low in heavy ends, particularly when contained at moderate pressures. For such gases the error in the calculated z is usually less than 2 to 3 per cent. However, the reliability of this approach becomes somewhat nebulous for gas condensate and volatile oil systems at high pressure. One logical approach has been to recognize the variation of 2,. This idea was first suggested by Meissner and Seferianl and used by Lyderson, Greenkorn and Hougen2 to prepare extensive tables of thermodynamic properties. Other third parameters have been proposed by Stockmeyer, Kihara, Riedel, Lightfoot, Bloomer and Pitzer. These were tested by Satter and Campbel13 for many gas mixtures and it was shown that they were inter-related. All of these third parameters have a common fault — they cannot be directly evaluated for the heptanes-plus fraction. Consequently, one necessary requisite of an improved method for predicting the density of multicomponent hydrocarbon systems, was development of a third parameter that could be evaluated for that fraction. PREVIOUS MULTICOMPONENT DENSITY PREDICTION METHODS Sage and Lacey4 suggested a method of using partial molal volumes for computing the density of hydrocarbon gas mixture for pressures to 3,000 psi. In this technique, they approximate the complex multicomponent gaseous mixtures by a quarternary system of methane, ethane, propane and butane. Sage, Hicks and Lacey5 suggest a method of using partial molal volumes for computing the density of hydrocarbon liquids. The results agree within 3 per cent of the experimental values. However, the composition range is limited to about 10 per cent by weight of methane. Consequently, this correlation does not cover the low-molecular-weight liquid similar to natural gasoline and high-pressure gas condensates.

Jan 1, 1966

By Rclssell Gibson, F. S. Turneaure

The tin deposit of Monserrat; Bolivia, consists of one major vein 1600 m in length. The ore is unusual because of the notable quantity of teallite, even though cassiterite is the principal tin mineral. The deposit, formed at shallow depth under a wide range in temperature, may be classed as xenothermal. Polished sections reveal a complex history of replacement, with low-temperature minerals deposited before high-temperature minerals.

Jan 1, 1950