Search Documents

By Carleton Ellis

(Presented at a meeting of the New York Local Section of the Institute, Apr. 12, 1912.) I. INTRODUCTION. THE problem of the influence of hot surfaces upon gaseous combustion is one which, from a purely scientific stand-point, has engaged, for many years past, the attention of Prof. William A. Bone, of Leeds University and the Imperial College, London; and as his recent work has been the direct outcome of earlier scientific investigation, it will be appropriate, by way of introduction, to review briefly the present position of science with respect to this important subject, as stated by Professor Bone. One may perhaps best arrive at an understanding of the term " ?flameless " or " surface " combustion by considering certain facts which differentiate it from the more familiar processes of combustion as they occur in ordinary flames. All hot surfaces have an accelerating influence upon chemical changes in gaseous systems. If, at any temperature, a gaseous system, A, tends to pass over into another system, B, contact with a solid at the same temperature will accelerate the process. To take a very simple example, if a mixture of hydrogen and oxygen in their combining proportions (electrolytic gas) were maintained in an inclosure with smooth glass walls at a temperature of, say, 450° C., there would certainly be a tendency to form steam, but the rate of change would be negligibly small. If, however, there were brought into the system some porous solid material at the same temperature, so that a large surface was exposed to the gases, the rate of change would at once be rapidly accelerated in the layer of gas immediately in contact with the hot surface. Steam, the product, would diffuse outward from the surface, and the supplies of hydrogen and oxygen at the surface would be renewed by diffusion inward. Thus combustion would proceed heterogene-

Sep 1, 1912

By T. Lane Carter

BEFORE describing the experience with the Chinese on the Rand and the work they have accomplished, it will be necessary, sary, first, to give a brief account of labor-conditions in the Transvaal since the war, and then to show how the necessity of importation of labor arose. As is well known, the Transvaal mines are run on the dual system of labor-that is, the rough work is done by colored laborers under the superintendence of white men. From the start of mining operations in South Africa there has been the cry of shortness of native labor, due in great measure to the failure of Kaffirs to work continuously in the mines. While he works, the Kaffir is a satisfactory laborer, but his period of service is short, averaging about nine months. People unacquainted with the Kaffir have maintained that, by offering a higher wage and better accommodation, better results would be obtained from the native workers, but an increased wage simply aggravates the trouble. The Kaffir's wants are few. While at work he spends little of his money, and before long has sufficient capital with which to buy wives and become a gentleman of leisure. Doubling the wage of the Kaffir means that he acquires a competency in half the time, so that his period of service is correspondingly reduced. In 1899, before the war, there was always a cry about the scarcity of Kaffir labor. The highest number of natives at work was in July and August, 1899, when nearly 100,000 were employed. At the outbreak of hostilities the Kaffirs were scattered far and near, many doing well during the war by working for the military authorities. On the, resumption of mining operations on the Rand a serious mistake was made. Based on past experience, it was argued that if the whole industry decided to start anew with

Sep 1, 1908

By L. C. WYMAN

THIS paper discusses what mining reports should contain when presented to the California State Corporation Department, to accompany applications for the sale of stock to the general public, but the principles involved apply to mine financing everywhere. Such reports should 'be as clear and concise as possible, endeavoring to tell the truth in as few words as necessary. Should the engineer be aware that his report is to be used in connection with the sale of stock to the general public, he should consider the public as his client as well as the person who actually employs him. It is always required that the engineer be favorably known and of recognized standing. The following points should be given careful attention : 1. A legal description and location of the property. 2. Transportation conditions, and how they may be expected to affect the operating costs. 3. A brief history of the property, its production record as to tonnage, grade, and character of the ore should be given. Should the property have suspended operations for any reason, this should be given. Any details of former operating costs should be given, especially as to how any improvement could be made, due to better methods which might be employed.' 4. The main geological features and whether they are such as to lead the engineer to believe that the mine may possibly 'be exhausted or the ore of such grade as to be no longer profitable. If he considers them favorable, he should give his reasons for the belief that further development work may produce profitable results. A map showing these features should be submitted, and it is not necessary that such map be highly colored or contain any more than the essential matters. 5. Other mines in the district, or those with similar

Jan 1, 1929

By W. A., Wasley

THE EL TIGRE MINE is a highgrade silver and gold producer located in the northern part of Sonora, Mexico. It has been worked continuously since 1903, producing 50,000.000 oz. of silver and returning handsome dividends. During 1930 and 1931 falling silver prices compelled the Tigre company to make representations before the Department of Labor in Mexico City showing the necessity for drastic reductions in wages and personnel. The delays in obtaining permission from the Federal Labor Board to make these readjustments caused the company to suffer considerable financial loss during those years. After the reduction in operations was finally effected, the Sonora state government headed by Señor Francisco Elias (former Governor, now Secretary of Agriculture) and Señor Rodolfo Elias Calles (present Governor and eldest son of Señor Plutarco Elias Calles, recently Secretary of War and former President of Mexico) have cooperated with the company to make continued operation possible by revising downward certain state taxes that would have been a factor in forcing the closing of this mine. Also, permission to change our workmen over to another system of mining was essential to continued operation.

Jan 1, 1933

By A. N. Rogers

Jan 1, 1883

By J. P. Heller, H. B. Bradley, A. S. Odeh

A potentiometric model technique is presented for determining the areal sweep efficiency of a five-spot well pattern, at and beyond breakthrough. A sharp interface between displaced and displacing fluids is assumed. Although the prototype svstem is referred to as a waterflood operation, obvious changes in the notation and computations will adapt the results to other displacement processes. The results of the study include the following. 1. Areal sweep efficiencies for a five-spot well pattern, at and beyond breakthrough, for mobility ratios (displacing to displaced fluid) of 4:1, 2:1, 1:1 and 1:4. 2. Extension of potentiometric analysis to the investigation of the areal sweep efficiency beyond breakthrough in a five-spot pattern by the application of conformal mapping and conductive-solid models. 3. The use of layers of conductive fabric in representing mobility ratio changes in potentiometric models. 4. The development of a probe mechanism for probing conductive solids. The results obtained by conductive-cloth models agree with earlier areal sweep efficiencies at breakthrough obtained by Aronofsky and Ramey 1 on the potentiometric analyzer using electrolytic-tank models. Results beyond breakthrough differ from those obtained by the X-Ray Shadowgraph technique. Data from this study show that, for mobility ratios greater than one, water cut rises rapidly as fluid is produced after breakthrough. However, for mobility ratios smaller than one, a large increase in area swept resulted with only a small increase in water cut. INTRODUCTION In calculating reservoir performance of waterflood-ing operations and other fluid-injection programs, it is necesssary to estimate the areal sweep efficiency * before and after injected-fluid breakthrough into production wells. Influence of mobility ratio on oil-production history, before and after breakthrough for a five-spot well pattern, has been studied by X-Ray Shadowgraph techniques 2-5 and by gelatin models.6 In none of these investigations was the transition zone controlled experimentally. Steady-state anaiog techniques assume that a vertical and discrete interface exists between the displacing and displaced phase. Thus, when using a potentiometric analysis, it is assumed that no transition zone exists. To determine the areal sweep efficiency beyond breakthrough for a five-spot well pattern using the potentiometric analyzer, four principal problems had to be resolved. These were the following. 1. The laborious method of representing changes in mobility ratio in electrolytic tanks by means of contoured wooden blocks. 2. Vapcrization of the electrolyte solution during the study causing concentration changes and, thereby, variable conductivity. 3. The scale-limitation problem 7 that is accentuated by abrupt eiectrolyte depth changes. 4. A wellbore geometry problem. EXPERIhlENTAL EQUIPMENT AND PROCEDURES CONDUCTIVE-SOLID MODEL The theory, equipment and procedural techniques of the electrolytic-tank potentiometric model have been treaced excellently by Lee8 and by Muskat.9 By the use of a conductive solid to represent the fluid conductivity of the porous media, the need for contouring wooden blocks to represent mobility ratio was eliminated. It was found that a carbon-black coated fabric, Uskon D-16,** could be employed as a fairly uniform conductive media. This material, when stacked in appropriate layers and pressed together, can be used to represent changes in mo-

By J. E. Harris

The metallic elements, beryllium, calcium, cerium, lithium, manganese, titanium, vanadium and zirconium are used in metallurgical practice in relatively small percentages for the purpose of improving the physical properties of various alloys. No important uses for any of these elements have thus far been developed either in the pure form or in alloys of which they constitute the major constituent.

Jan 1, 1935

By R. Van A. Norris

The following tests were made, during 1889, for the Susquehanna Coal Company, to determine the relative efficiency of several styles of mine-car wheels in use at their collieries at Nanticoke, Pa. The wheels experimented upon may be divided into two classes: The "old style" (Figs. 1 and 2), which are oiled at every trip; and the "new style" (Figs. 3, 4, and 5), which require oiling about once in two to four months. Fig. 1 shows a section of a plain cast wheel, with patent annular oil-chamber. This is held in position on the axle by a square, split cotter-pin. Fig. 2 is a similar wheel, with a patent cast bushing, which is readily replaced when worn. The lubrication is effected by a simple oil-hole, but the oil is delivered a little inside of the gaugeline of the wheel, where it is most needed. Figs. 3, 4, and 5 are sections of a " new style " patented, self-oiling wheel. In this, the outer end is cast closed, and the wheel is fastened to the axle by a spring cotter-pin passed through one of the plugged holes. Dirt is prevented from entering the open end by a cap, with faced end and packing-ring, fitting over the end of the hub. The lubricant is introduced into the oil-chamber through one of the plugged holes in the hub. When the wheel is in motion, the lubricant is thrown by centrifugal force away from the axle, enters the two ports shown, and is

Jan 1, 1890

By J. W. Freeman, R. F. Decker

A microstructural investigation was pursued to establish the mechanism of the pronounced benefits of traces of boron and zirconium on creep properties of a 55 Ni-20 Cr-15 (20-4 MO-3 Ti-3 A1 alloy at 1600°F. The mechanism of improvement of creep properties was found to be a pronounced stabilizing effect of traces of boron and zirconium on the grain boundaries of the alloy. The alloy with low boron and zirconium was subject to rapzd agglomeration of M23 C6 and in the grain boundaries, followed by depletion of y ' and intergranular microcracking at the grain boundaries transverse to applied stress. Brittle fracture then occurred by linking of microcracks. However, additions of zirconium, boron, and boron plus zirconium decreased this tendency in that order, allowing longer creep exposure and higher creep defor.mations before fracture occurred. VERY little information has been published describing the mechanism by which trace amounts of boron or zirconium improve the creep properties of complex nickel-base heat-resistant alloys, although the effect is now well recognized.1-4 Because the phenomenon is so important to properties and the effects are so striking, a study was made of the mechanism in a 55 Ni-20 Cr-15 Co-4 Mo-3 Ti-3 A1 alloy. It was believed that such a mechanistic approach would increase knowledge in theory of alloying and give a more basic understanding of alloy design to resist creep. The basic premise of the study was that boron or zirconium would alter the microstructural characteristics controlling creep and fracture to the extent that the effects could be identified by light and electron microscopy and by electron diffraction techniques. Characteristic of the microstructure of the Ti + Al-bearing nickel-base alloys is the dispersed precipitation of the intermetallic compound Ni,(Al, Ti), the ? ' phase, which is generally con- sidered to be the major source of high creep resistance.5-7 In addition, carbide phases have been identified8-10 and these can alter creep properties markedly.11 Since both the ?' and carbide transformations have been found to control properties, careful attention was paid to the effect of boron and zirconium on these transformations.

Jan 1, 1961

By D. R. Shoemaker

BACKGROUND AND PROJECT DESCRIPTION A 16.5 kt per day underground molybdenum mine is being developed at Questa in northern New Mexico by Molycorp, Inc., a wholly-owned subsidiary of Union Oil Company of California. Small scale underground mining first began in 1920 and large scale open-pit mining was initiated in 1965, but because of the high stripping ratio, surface mining is being phased out. Construction of the underground mine began in 1979, and first production is scheduled for 1983. Full production of 9 Gg of molybdenum per year will be reached in 1984. Access to the mine will be through a service shaft, development shaft, and a conveyor decline. 'The service shaft, 7.3 m in diameter and 396 m deep, will be used for personnel, supplies, development muck, and fresh air intake. It will be equipped with a large, double-deck man and material cage. A double-drum hoist will be used for cage hoisting and will handle up to a 27-t load in balance with a counterweight. Development muck will be loaded into skips in balance and a single-drum auxiliary hoist will provide secondary access. The 396-m-deep, 4.3-m-diameter development shaft will be used for initial mine development, mine exhaust air, and a slick line pass for concrete entering the mine. The development shaft is located 400 m north of the service shaft. Run-of-mine ore will be transported from one of two 1.4-kt storage pockets by a 1.2-m-wide conveyor belt located in the 10°, 1980-m-long, 5.0-m-wide, and 4.6-m-high decline. The decline conveyor belt has a centerline length of 2229 m and a vertical rise of 363 m. It will be powered by four 448 kw motors driving a single drive pulley. There will be two 1.2 m transfer belts on the surface with centerline lengths of 322 m and 542 m. All three conveyor belts will be reinforced with steel cables. On the surface, in addition to the headframes and hoist houses for the two vertical shafts, a large maintenance shop, warehouse, compressor house, change house, main office building and timber framing building have been constructed.

Jan 1, 1981

By A.A. Grubb, F.L. Wolf

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By F. L. Wolf, A. A. Grubb

The tests here described were rrlade to obtain information regarding costs, efficiency, etc. of baking cores in an oil-fired oven and two electric ovens, which were installed, early in 1920, in the core room of The Ohio Brass Co. and were used almost continuously during the rest of that year. Operating costs were rather high so a complete test was undertaken early in 1921. The ovens will be referred to as Nos. 1, 2, and 3. Nos. 1 and 2 are electric ovens of different makes while No. 3 is an oil-fired oven made by the firm that made No. 2. The three arc. equipped with similar ventilating devices. They have full-height doors at front and rear. The cores are placed on iron racks, which arc lifted by Cowan trucks and rolled into the ovens through the front doors. When baked, they are removed through the rear doors. Fig. 1 shows the general plan of the elecric ovens while Fig. 2 shows the plan of the oil-fired oven. Oven No. 1 is 91 in. (231 em.) wide, 83 in. (210 em.) high. and 79 in. (200 cm.) deep, inside measurements. The walls are constructed ill panels about 18 in. (46 cm.) wide and 43/16 in. (10.6 em.) thick, packed with blocks of insulating material and covered with sheet iron. Thc concrete floor oil which the owns set is 13 in. (33 cm.) thick. 4 recess about 5 in. (13 cm.) deep was cut in the floor to provide room for the heating units. Channels and plates supported on I beams serve as supports for the trucks and racks. The ventilating system consists of a Sirroco No. 11/2 fan, connected so as to draw air from the top of the oven or from the room, through damper C, and to deliver it either to the bottom of the oven or to the floor; the delivery is controlled by the vane A. The fan 2nd pipes are covered with 1/4-in. (6.3 mm.) asbestos-cement lagging. The heating units have a capacity of 91.4 kw. and arc located along

Jan 1, 1923

By M. E. Fine, A. A. Hendrickson

The critical resolved shear stress and the strain rate dependence of the .flow stress are reported for Ag base A1 single crystals up to 6 at. pct A1 over a temperature ralzge of 4.1° to 470°K. At room temperature the solid solution strengthening is attributed brinciballv to an increase in the dislocation density on alloying. At 42°K the alloys are relatively stronger because the dislocations widen on alloying and are more difficult to cut. In a previous paper, the authors reported the characteristics of strain aging in Ag base A1 alloys.' The variation of the magnitude of the strain-aging yield drops on aging time, aluminum content, and testing temperature strongly indicated that the phenomenon is due to the Suzuki mechanism. In the present paper, the critical resolved shear stress (CRSS) and the strain rate dependence of the flow stress are reported for Ag base A1 single crystals as functions of testing temperature (4.2" to 470") and A1 content (0 to 6 at. pct). Observations on the substructure and measurements of the effect of crystal growth rate are also given. The experimental re- sults appear explainable considering that aluminum additions increase the dislocation density and dislocation width. EXPERIMENTAL METHOD The methods of specimen preparation and tensile testing were described previously.' Briefly, single crystals were grown from the melt in a vacuum (1 x lom5 mm Hg), shaped into tensile samples by a combination of abrading and acid etching, annealed at 850°C in a vacuum (1 x 10" mm &Z) for several days, and furnace cooled to 200'. The testing was done on a model TM Instron using friction grips and a strain rate of about 5 x 106 per sec unless otherwise noted. The various testing temperatures were obtained by immersing the specimens in the following media: 1) 4.2': liquid helium using the apparatus of G. Byrne;' 2) 77°K: liquid nitrogen; 3) 200"K: dry ice and acetone; 4) 415' K: ethylene glycol; 5) 460' \ to 480' : molten Stanalax. In the determination of the CRSS above 296' K, a ratio method was used; the crystals were strained initially at the higher temperature, 0.1 pct shear strain, and then tested at 296' . The ratio of the flow stress between the two temperatures was then multiplied by the average CRSS at 296' K to obtain the value of the CRSS at the high temperature. (The test at 296' showed a yield point resulting from strain aging; the flow stress at 296' K was taken as the lower yield stress.) The ratio method, we believe, is more accurate than using different crystals since

Jan 1, 1962

By J. M. Seeman, R. A. Dodd

If some solution-quenched supersaturated aluminum solid solutions, e.g.., Al(Cu), are plastically deformed at room temperature and then aged at 200oC, the hardness may first decrease before increasing in the usual manner ' A similar transient softening is observed, even in the absence of plastic deformation, when a thin foil or small-diameter wire Al(Cu) specimen is rapidly quenched from the solution-treatment temperature and then aged.' Also, some solution-quenched and neutron-irradiated alloys undergo an initial hardness decrease during subsequent aging.3 The usual explanation of the transient softening in the above examples involves the effect of vacancies introduced by plastic deformation, rapid quenching, and neutron irradiation, respectively However, the mechanism of softening is not unequivo-cably established. In the first-noted case, Gane and parkins' observed that the softening was approximately proportional to the difference in the atomic diameters of solute and solvent, and it was argued that, if a large relative difference in atomic diameter promoted vacancy-assisted room-temperature solute diffusion to dislocations, dislocation climb occurring during subsequent aging at 200°C could cause transient softening. Some substantiation of this theory was offered by the additional observation that discontinuous yielding of solution-quenched polycrystalline Al(Cu) tensile specimens was suppressed by interrupting the test for a short aging treatment at 200°C. Of course, reversion (resolution of GPI) at 200°C would also cause softening, and Sil-cock4 expressed the opinion that the softening in the case of Al(Cu) must be partly associated with reversion. Also, Hirsch5 commented on the possibility that, if jogs cause hardening, an anneal at 200°C should straighten the jogged dislocations and result in softening. However, parkins' has re-expressed his belief that these mechanisms are not entirely consistent with the observed serrated stress-strain curves. Experimental. New data has now been obtained for Al(Cu), Al(Ge), Al(Mg), and Al(Zn) primary solid-solution alloys. These alloys were prepared from metals exceeding 99.99 pct purity, and specimens 4 by 4 in. diam were solution-treated, quenched, deformed 10 pct in compression at room temperature, and aged at 200'C in a cottonseed oil bath for various times. Generally, these operations could not be carried out in rapid succession, so the alloys were stored in a freezer between treatments to minimize aging. The variation in hardness with aging time, Figs. 1 to 4, was determined by microhardness testing with a 3.0-kg load. At least five readings were averaged to obtain each data point, and all measurements were taken about the center circumference of each cylinder (region of maximum deformation). Each specimen was used to obtain only one data point, i.e., specimens were not replaced in the aging bath after measurements were made. In

Jan 1, 1968

By John Henderson

Densities of melts 0f the lime-iron oxide-silica system in contact with solid iron have been measured by the maximum bubble pressure method in the temperature range 1250° to 1440°C and the composition range 0 to 40 mol pct lime, 15 to 100 mol pct iron oxide, and 0 to 55 mol pct silica. Densities range from 4.65 g cm 3 for wustite at 1440°C to 2.75 g cm-&apos; at 1350°C for a melt containing 30 mol pct lime, 20 mol pct iron oxide, and 50 mol pct silica. The results are interpreted in terms of a postulate that the melts can be regarded as a random array of oxygen ions in which regions of local order exist to satisfy the coordination requirements 0.f the cations. An understanding of the nature of metallurgical slags is basic to the development of a sound theoretical description of heavy metallurgical extractive and refining processes. Because these liquids are complex, direct measurements of their properties has not thrown much light on their structure. This has led to the approach of measuring the properties of simpler liquids, and building up their complexity until slag compositions are reached. In this way the density of liquid iron silicates was measured in a previous study1 and the present work represents a further stage in this synthesis. EXPERIMENTAL The technique used in the measurement of density was the maximum bubble pressure method. Details of the apparatus and procedure were similar to those previously reported,&apos; with the exception that a constant voltage transformer was used to supply the power input to the furnace and six silicon carbide resistance elements were used in place of the molybdenum winding. With these modifications melt temperature could be maintained within 1 centigrade degree during the course of a run. The silica used to prepare the melts was washed natural quartz ignited at 1000°C; wustite was prepared by air-melting A.R. grade ferric oxide in an iron crucible and lime was prepared by air ignition, at 1000°C, of weighed quantities of A.R. grade calcium carbonate, previously air-dried at 110°C. The finely ground constituents were intimately mixed in a glass ball mill prior to melting. Temperatures quoted are accurate to * 5°C and the standard deviation of the density values, calculated by the method of least squares, ranged from 0.5 to 1.8 pet. However, replicate determinations of density on different melts of the same nominal composition at the same nominal temperature did not vary by more than 1 pct, Table I, and this figure has been taken as an estimate of the accuracy of the density results. The density of carbon tetra-chloride was also measured as a check on the absolute performance of the experimental method. At 20°C a value of 1.593 * 0.002 g cm"3 was obtained; this compares with the literature value2 of 1.595 g cm"3. Results of experiments designed to measure the dependence of the density of lime-iron oxide-silica melts, in contact with solid iron, on composition and temperature are shown in Table I. Because iron sometimes precipitated in the sample during quenching, the Fe203 chemical analyses were only poorly reproducible and should be taken as a guide rather than as absolute values. Fig. 1 shows the data from various sources for the density of liquid iron silicates and Fig. 2 shows isodensity contours at 1410°C for lime-iron oxide-silica melts, calculated by graphical interpolation of smoothed curves drawn through the experimental results, together with the 1400°C results of Adachi and ogino3 and Pope1 and Esin.4 Fig. 3 shows the isothermal variation with composition of the volume of melt per gram ion of oxygen at 1410°C and Fig. 4 shows regions in which the temperature coefficient of this volume is negative, positive, or negligible (<0.005 cm3 deg-I). DISCUSSION a) Disparity Between Reported Density Results. Consider the system iron oxide-silica, the results for which are summarized in Fig. 1. Although there is some difference in the temperatures at which the various densities apply, this difference is not sufficiently large to account for the observed discrepancies. The reliability of the present results for the low-silica region has been confirmed by measurement of the density of liquid wustite by three different techniques. At 1410°C the density measured by a balanced-column method was 4.55 g cm"3, by a combination balanced-column and gas-densitometer method 4.59 g emd3, and by a pycnometer method 4.53 g cm"3. Schenck, Frohberg, and Hoffermann&apos; have also reported a value of 4.55 g cm"3 for the density of liquid wustite at 1400°C. It must be concluded, therefore, that neither Pope1

Jan 1, 1964

By R. V. Horrigan

High purity ZrC14 (25 to 200 ppm of metallic impurities) can be readily prepared in simple apparatus by thermal decomposition of alkali chlorozirconate fused salts at 500° to 600°C and at atmospheric pressure. Suggested phase diagrams for the systems NaCI-ZrC14 and KCI-ZrCI, are presented. ALKALI chlorozirconate compositions — anhydrous fused mixtures of ZrCl4, NaC1, and KC1— are manufactured commercially and are used by the magnesium industry to introduce zirconium into magnesium alloys. Zirconium refines the grain size and improves the physical properties of many important magnesium alloys. In the course of working with chlorozirconate compositions of high ZrCl4 content, it was noticed that these salts decomposed progressively itwaswith increasing temperature to yield considerable amounts of a ZrCl4 sublimate of high purity together with a solid chlorozirconate residue. Further research led to: 1—improvements in the

Jan 1, 1956

By A. Cochardt, D. H. Feisel

HE success of the sintered aluminum powder material (SAP)&apos; in raising the maximum useful temperature of aluminum alloys has stimulated effort in investigating similar systems in which the metallic matrixes have higher melting points. Examples of such systems which have been studied are nickel-alumina,2, 3copper-silica,4 copper-alumina,4 titanium-cerium oxide,5 and 80/20 nickel-chromium,8 cobalt,= and molybdenum7 matrixes with various hardeners. Conventional precipitation-hardened high-temperature alloys are often thermally unstable in service. The original fine particles that are responsible for good strength properties grow in size at elevated operating temperatures, a process termed "over-aging." This growth of precipitated particles causes a gradual loss in strength properties. A previous paperb describes the factors that govern the process of overaging, and estimates the time required for overaging of a nickel-alloy matrix dispersion-hardened by various precipitates such as are found in current high-temperature alloys, and by alumina. These calculations indicate that nickel-base alloys hardened with Ni3Al, Tic, or TiN are quite unstable at 1340" F (727°F). Such alloys should overage within a few hours at that temperature. A nickel-base alloy hardened with alumina, on the other hand, should behave differently. It should not overage appreciably within a thousand years. It was further shown8 that the thermal stability of the oxide-hardened alloy is mainly due to the low solubility of oxygen in equilibrium with alumina in the nickel-base matrix. Since the oxygen solubility is small, little oxygen can diffuse, and structural changes require very long times. This paper illustrates the effects of time and temperature on the structural stability of nickel alloy matrixes hardened by dispersions of Ni3A1, Ni3Ti, Tic, and alumina, and of nickel-chromium matrixes hardened by alumina. Hardness measurements and metallography have been used as a measure of structural stability. EXPERIMENTAL PROCEDURE Using the best information from published phase diagrams,&apos;-l4 compositions of the Ni-Al, Ni-Ti, and Ni-Ti-C alloys were determined so as to have 5 vol pct of precipitate at 1350° F(732°C), the temperature selected to illustrate the effect of time on structural stability. Table I lists the chemical compositions of these alloys. Standard laboratory melting and alloying techniques were used in preparing ingots of the F-Series of alloys. The cast ingots, 1 3/4 in. in diam, were forged to 3/8-in. diam rods.

Jan 1, 1960

By John M. Lovejoy

FEDERAL regulation of the petroleum resources of the nation has long been an interesting topic for discussion. A plan to accomplish Federal control has now taken definite form. At the request of the President of the United States, a bill to be known as the Petroleum Conservation Act of 1939 has been presented to Congress-H. R. 7372, offered by Representative Wm. P. Cole, Jr., and more usually known as the Cole bill. It is an act ostensibly designed to conserve our petroleum resources, through regulation of production practices. Hearings are being held currently by a subcommittee of the Interstate and Foreign Commerce Committee, in compliance with the request of the President to report the bill early in the next session of Congress.

Jan 1, 1939

By F. Robertson Jones

IF the tendency toward extending the scope of the workmen&apos;s compensation system to include life, health, accident, old age, and unemployment insurance for workers is not promptly altered, I believe there will be a complete breakdown of that system. This is not because of any objections, there may he to requiring industries to provide these additional forms of protection in whole or in part to their employees. It is rather because our workmen&apos;s compensation laws, their scale of benefits, and the administrative procedure under them are not adapted or suited to such situations. If the compensation principle is limited to its own proper sphere and is not enlarged so as to include all the ills that the flesh is heir to, it is practical, "workable, and beneficent. If it invades foreign realms, it is bound to grow into a veritable Frankenstein&apos; which will harm principally those it &apos;is supposed to aid, and, at the same time, will promote waste, fraud, and Industrial demoralization. Compensation risks will become almost uninsurable; the cost to business will be intolerable; and the development of sound relief measures which will give to labor the protection now sought by the uneconomic device of enlarging the compensation law territory will be retarded.

Jan 1, 1934

By John V. Beall

HEAVY-DENSITY separation processes, a commercial application of the sink-float test used in mineralogical laboratories for the separation of mineral particles by their difference in specific gravity, are the biggest development in mineral dressing since flotation, which was at about the same stage of development thirty years ago. The scope of their application has broadened and, though still in the development stage, they are being accepted in a constantly increasing number of commercial installations. This progress in mineral beneficiation is especially satisfying when we realize that our high-grade ore deposits are fast disappearing and a big factor in determining whether a hole in the ground is being sat upon by a liar or an honest citizen is how economically the ore dressers can concentrate comparatively low-grade ores. As early as the middle of the nineteenth century attempts were made to use aqueous salt solutions in a heavy-liquid separation for cleaning coal. But the original and recovery costs of these liquids were high and further, the fact that they were corrosive, unstable, and toxic added to the difficulty in using them.

Jan 1, 1948