Search Documents

By V. C. Williams

Some of the physical, chemical, and electrical processes for conversion of saline water to potable or industrial water are economically surveyed from an engineering viewpoint. Since all these processes require energy for drive and equipment for containment, the correlative economic factors are developed which indicate directive influences in the choice of particular regional processes. The supply of natural waters and its distance also affect decision. Any one process will probably not prove dominant in the field because auxiliary considerations such as the saline water source; types and continuing availability of fuel; electric power use or recovery; area economic status and advancement; and the political pressures of population, group demands, and land use tend equivocally to obscure capital and operation cost decisions. Basic engineering considerations, data, and economic factors are presented to assist in the direction of these decisions. An exploding world population, increasing industrialization, advancing standards of living, and the desire of less-privileged nations for betterment focus attention sharply on a major problem: water. *19 Up to now, in retrospect, people have had it relatively easy in the handling of this problem. All the better dams in the most advantageous sites, the better aquifers, the shortest aqueducts have been built. In another phase of the problem, concern is evident that wastes cannot indefinitely be disposed of merely by keeping them dilute and discharging them promiscuously. 7-9 And, perhaps, as past civilizations have done,l5 water, watersheds, streams, and irrigation may have been mismanaged or, at the least, not adequately studied.3,5,36,37 In this last is perhaps the core of the problem. As Gross states, "Ignorance and too often, indifference are contributing factors. Archaeology and theology both furnish ample testimony to the existence of rich lands where deserts now stand; it was man who ravaged his land. Unless education is a companion to water development, development might as well be forgotten. But without water, there is no beginning."13 The U.S. is showing increasing concern about its water for predictions are that by 1980 the daily withdrawals will be 494 billion gal, a figure nearly equal to the dependable supply.Is This is based on a conservative projected population of 230 million. The major categories of withdrawals are: To make available this per capita average of 2150 gal per day will require an expenditure of $219 billion over the next 20 years. The U.S. is not alone in this concern. The United Nations shows as arid zones of the world: all of Africa north of the equator and south of the 20's parallel; all of the Arabian peninsula; all of the middle east and Iran, Iraq, Pakistan, Afghanistan, northern and central India; a great band about 1000 miles wide along the 40'~ parallel from the Caspian Sea east across Russia through China to the Pacific Ocean; all of Australia except the coastal plain; the Caribbean Islands; the western nations of South America; and the western third of the United States and of Mexico. With one quarter of the earth's 57,500,000 sq miles of land thus suffering from lack of good water, increasing attention goes to the treatment of brackish and sea waters. The U.S. has been a leader in this field4,12, 16123,24 through its Office of Saline Water in the Dept. of Interior because even now some of its cities and regions are short of potable water. 11j'7,M Industrial water is also of vital concern as a result of ever higher industrialization1,14122 Other nations, among them JaPan, Israel,13188 Germany, Union of South Africa, Australia, Netherlands, France, Yugoslavia, Russia, and groups such as the Organization for European Economic Cooperation (OEEC)' are also diligent. The objective is low cost water, which means that both technology and economics have prominent roles in saline water conversion processes. TECHNOLOGY: SALINE WATER CONVERSION A number of reviews of methods have been made, principally by staff members of the Office of Saline Water (U.S. Dept. of Interior). Jenkins,31'32 Gillam,34p

Jan 1, 1962

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By J. E. Pavlick, W. W. Mullins, H. W. Paxton

The growth of nitrogen-austenite during nitriding of large-gvained ferrite between 650" and 800°C has been studied as a functimz oJ time and nitrogen potential of the atmosphere for a variety of alloying elements dissolved in the ferrite. Whereas no preferential grain boundary penetration by aistenite takes place in zone-refined iron, the addition of aboit I zot pct oj' V, Ti, Cr. Si, or A1 produces significant protrusion of austenite down former 0-0 boundaries. This group of elernents also produces ragged y-0 interfaces in the a grains which advance more slozuly than those in zone-refined iron. 1 zut pct of Ni, Co, Mn, or Mo dissolved in ferrite leads to essentially smooth 7-a interfaces, which advance at rates very sinzilar to those in zone-refined iron. The reasons for this effect are not clear. Two possible limiting hypotheses, not necessarily exclusive, are discussed. One involves p.referentia1 grain bozindary diffusion of nitrogen. the other the production of a zone of ferrite, stpersatcirated with respect to nitrogen, from which austenite precipitates helerogeneozisly on the a-a gyain boundaries. In many phase transformations which occur by nu-cleation and diffusion-controlled growth, information on the parameters which control the rates of nuclea-tion and of growth is frequently not quantititative. The present work describes a continuation of efforts to obtain quantitative data on growth rates in systems where thermodynamic and kinetic factors are known independently, and thus where comparison with models of the growth process is possible. The work has been conducted on iron-base systems for two reasons. Firstly, there are several interesting transformations in this system, many of which are of practical importance. Secondly, the information on phase diagrams, activities, and diffusion coefficients is more complete in this system than in any other. These data are still inadequate to check all the effects of alloying elements, but at worst it is possible to make estimates and thus examine order-of-magni-tude agreement with proposed models. It will be necessary to do this in the present work. The problem studied was the growth of nitrogen-austenite in from the surface of large-grained columnar crystals of alloyed ferrite exposed to an NHs/Hz atmosphere. Earlier work by Grozier et al.' had suggested that growth of austenite may occur preferentially along grain boundaries of alloyed ferrite, whereas zone-refined (ZR) iron shows no such effect, Fig. 1. Growth of nitrogen-austenite into single crystals of zone-refined ferrite is planar provided sufficient nu-cleation sites for austenite are present, and is controlled by volume diffusion of nitrogen through the

Jan 1, 1967

By M. C. Flemings, T. Z. Kattamis

Dendrite morphology and grain size were studied in bulk samples of iron and nickel base alloys under-cooled up to 300°C. In the alloys studied, dendrite morphology gradually changes with increasing undercooling from the usual dendritic structure to a structure composed of cylindrical dendrite arms. At a critical undercooling of approximately 170°C in these alloys there is an abrupt transition to a fine-grained structure of spherical morphology. Final dendrite-arnz spacing of melts nucleated at less than the critical undercooling decreases with increasing undercooling and with decreasing distance from a chilled surface. Grain size of melts nucleated at greater than the critical undercooling decreases similarly with these factors. It is concluded that structure coarsening, with reduction of surface area as driving force, is the principal mechanism determining final dendrite-arm spacing in melts nucleated at small undercoolings and grain site in melts nucleated at large undercoolings. IN solidification of highly undercooled melts, nuclea-tion and growth of the solid is accompanied by a rapid release of latent heat of fusion. The heat release is sufficiently rapid in bulk specimens that it takes place essentially adiabatically with respect to the surroundings; hence the specimen heats up ("recalesces") to some maximum recalescence temperature. For bulk liquid metals and alloys, a simple thermal balance shows the undercoolings obtainable in bulk samples are not sufficient to lower the maximum recalescence temperature below the equilibrium solidus temperature. Hence, some liquid always remains at the end of recalescence; this liquid must solidify by rejection of heat to the surroundings. Metals, including iron and nickel base alloys, normally freeze with only a few degrees of undercooling. In general, nucleation begins on impurity particles present in the metal, at a "heterogeneous nucleation temperature" that is quite close to the equilibrium liquidus temperature. Very small droplets of metal can be undercooled considerably before nucleation occurs,1-4 presumably because subdivision of the liquid reduces the probability of solid impurity in a given droplet. Following early work on metal droplets,' a series of studies has shown that it is possible, without great difficulty, to undercool bulk samples of many metals and alloys. Undercoolings obtainable are approximately two tenths of the melting point for nickel, iron, copper, and other metals and alloys.5-9 Specimen sizes have generally been in the range of 50 to 500 g. Studies on undercooling to date have been concerned primarily with techniques of undercooling and with nucleation and growth kinetics. Only limited consideration has been given to dendrite morphology in under- cooled alloys. One such study, in bulk Cu-Ni alloy,8 showed that at small undercoolings a typical dendritic structure was obtained. At undercoolings the order of 175°C the structure of a Cu-40 pct Ni alloy became "ray or starlike", and a dense network of subbound-aries appeared. At still larger degrees of undercooling, of the order of 250°C, the structure became more random and included an ensemble of globular forms. Comparable results were obtained by walker10 on Cu-Ni alloys, and by Kamenetskaya et al.11 in research on Cu-Ni, Sb-Bi, Fe-Ni, and Fe-Cr alloys. In this work, study was made of the processing parameters influencing dendrite morphology and grain size in undercooled alloy melts. Experiments were specifically designed to show the effects of coarsening ("ripening") during solidification on final casting morphology. EXPERIMENTAL PROCEDURE Apparatus used was patterned after that of Walker,10 Fig. l(a). Melting was by induction under reduced pressure of helium. Two different types of crucible materials were used; there was no difficulty in obtaining substantial undercooling in both types of materials. Alumina crucibles were used for the bulk of the runs made, with a glass coating separating the metal from the crucible walls. Other runs were made using fused silica crucibles with or without slag coating. A graphite susceptor was employed around the crucible to aid in melting and to reduce melt stirring. The major portion of the experimental work was on

Jan 1, 1967

By Andrew L. Mular, K. K. Humphreys

Introduction Estimates performed on potential future plants must by their very nature be either order-of-magnitude or budget (preliminary) estimates. Of the three types of estimates recognized by the American National Standards Institute (ANSI Standard Z94.2), order-of-magnitude and budget estimates are the least accurate. Order-of-magnitude estimates have an expected accuracy of plus 50 percent to minus 30 percent. In other words, it is anticipated that actual project cost will be no more than 50 percent above the estimate and no less than 30 percent below the estimate. Budget estimates, or preliminary estimates as they are often called, have an expected accuracy of plus 30 percent to minus 15 percent. The reason that greater accuracy cannot be expected in performing estimates on proposed new facilities is simply that insufficient data is generally available to permit performance of a highly accurate estimate. As stated in ANSI Standard Z94.2, a definitive estimate, i.e., an estimate with an expected accuracy of plus 15 percent to minus 5 percent," . . is an estimate prepared from very defined engineering data . . . (including). . .as a minimum, fairly complete plot plans and elevations, piping and instrument diagrams, one line electrical diagrams, equipment data sheets and quotations, structural sketches, soil data and sketches of major foundations, building sketches and a complete set of specifications." In other words, the engineering of the project must be fairly well underway to permit a definitive estimate to be performed. Such is the case only after the construction decision has been made, all potential alternatives evaluated, and major expenditures committed for a particular course of action. This situation is beyond the scope of this chapter. The chapter is directed to comparison of various technological alternatives for which site specific engineering data is not generally available. Accordingly, such comparisons can be made only by utilizing preliminary or order-of-magnitude estimating techniques.

Jan 1, 1982

By J. Stubbins

1 1.4-1. Source of Water. Precipitation in the form of rain or snow is the original source of water that enters most surface mines. The precipitation, which does not escape to the atmosphere, either becomes surface run- off or infiltrates into the ground to become ground water (3,4). Evaporation and surface run-off can be measured. The water that infiltrates the ground disappears from view and is more difficult to evaluate. In general, it moves in a pattern similar to the surface run-off, but at a much slower rate, since its progress is impeded by many subsurface conditions. The infiltrating water descends through the soil and rock by whatever passageways permit flow until the water table or top of the zone of saturation is reached. Though usually pictured as a level surface, it is dependent upon the topography and the permeability of the enclosing material, and therefore it can be as erratic and unpredictable as the subsurface geology. Ground water may become surface run-off again at a lower point, and likewise, surface run-off of lakes and streams can infiltrate to become ground water. Should the ground water be confined to a permeable zone overlain by an impermeable barrier, a pressure is created. Such water is said to be artesian if the pressure head is sufficient to raise the confined water to the surface. These conditions are more commonly found in relatively flat-lying bedded formations. 11.4-2. Recognition and Estimation of Water. Dewatering and flood control should be considered by the design engineer at an early stage in all surface mine planning. Recognition of the possible problems, and making allowance for their solution, is an inexpensive precaution. Circumstances which should lead to investigation are: 1. High rainfall 2. Experience of other mines in the area 3. Evidence of water and caving in drill holes 4. Presence of springs and artesian wells 5. Geological evidence of aquifers.

Jan 1, 1968

By G. E. Pellissier, P. H. Salmon Cox, B. G. Reisdorf

Banding that occurred in plates rolled from the early production heats of 18Ni(250) maraging steel is described and related to the segvegation of certain alloying elements (nickel, molybdenum, titanium), the extent of which was quantitatively evaluated by means of electron-microprobe analysis. The effect of banding on mechanical properties is discussed, with particular reference to observed directional differences in plane-strain fracture toughness of plates. It is shown that banding originates as interdendritic segvegation during ingot solidification and persists in some degree through normal soaking and hot reduction to plate. The results of the study showed that heating sections of small laboratory-cast ingots at 2200°F for 4 hr was sufficient to markedly reduce microsegregation and to considerably improve mechanical properties. Hot rolling of 7-in.-thick ingot sections to 1/2-in.-thick plate effected a similar reduction of microsegregation, but resulted in even greater increases in ductility and toughness than that obtained by homogenization treatment alone. DURING the past few years, considerable attention has been directed towards the low-carbon, high-alloy maraging steels and in particular towards the 18Ni-8Co-5Mo-0.4Ti alloy. The steels of this group, having an excellent combination of high strength and toughness, have a number of advantages over their more conventional medium-carbon low-alloy, quenched-and-tempered counterparts. In the annealed condition, the maraging steels are in the form of a ductile marten-site; aging at a relatively low temperature, typically 900°F for 3 hr, increases greatly the strength through the precipitation of intermetallic compounds. One problem in the early production heats of maraging steel was that the finished plate frequently displayed a banded structure. Previous work on other steels1-' had established that banding in wrought products is either a direct or an indirect consequence of chemical segregation, which occurs during solidification and persists to some extent through normal thermal and mechanical treatments. For example, Smith and others: in a study of low-alloy steel, were able to correlate the severity of banding in the wrought product with the degree of interdendritic segregation of nickel and chromium in the as-cast ingot. The effect of banding on the mechanical properties of steels is usually considered to be detrimental, although there is only limited evidence to suggest that a marked improvement in properties can be obtained with less heterogeneous structures. Comparison of the longitudinal and transverse tensile properties of banded and of homogenized 4340 steel showed that only the transverse ductility was improved by homogenization, but even then the improvement was not commercially significant.' Conversely, homogenization of through-the-thickness tension specimens of quenched-and-tempered steel plate, containing 1.47 pct Mn, increased the strength by as much as 10 pct and the tensile ductility by at least a factor of twos5 This improvement was related to the elimination of manganese-rich bands, which also are one of the factors responsible for cold cracking in the heat-affected zone of metal-arc welds.7 In the present study the nature and severity of banding in early commercial 18Ni(250) maraging steel plate and in laboratory-melted 18Ni(250) maraging steel plate was determined. The effects of banding on plane-strain fracture toughness and the effects of thermal homogenization treatments on the strength, tensile ductility, and toughness of 18Ni(250) maraging-steel as-cast ingots and rolled plate were evaluated. In addition, the effects of hot deformation by rolling on the mechanical properties of ingots were determined. 1) STUDIES OF BANDING IN EARLY PRODUCTION PLATE The chemical composition of the steel (A) used in this part of the investigation is shown in Table I. Banding was not clearly evident in either as-rolled or annealed* plate, but annealed and agedc** plate had a banded structure. The typical banded condition, Fig. 1, consists of layers of unetched austenite (white) and dark-etching martensite in a light-etching martensitic matrix. X-ray diffraction measurements showed that this steel contained more than 6 pct austenite. An electron-probe X-ray microanalyzer (using a focused beam of electrons) was used to determine the composition of the bands and of the material between the bands with respect to the main alloying elements— nickel, molybdenum, titanium, and cobalt. The recorded X-ray intensities were converted to concentration values with the use of a standard of similar composition. To facilitate probe positioning, all analyses were conducted on specimens that had been given a light etch. The influence of this etching on the analytical results was negligible; analyses made on the identical area before and after etching yielded essentially the same concentration values. The results of the electron-microprobe analyses at selected points revealed that the layers of austenite and adjacent dark-etching martensite contained greater amounts of nickel, molybdenum, and titanium than did the surrounding matrix, Table 11. The austenite layers

Jan 1, 1968

By Andrew Mayer

Early in 1942 National Lead Co. was requested by the War Production Board to construct and operate a plant for the Government to produce magnesium by the ferrosilicon process which had been developed by Dr. E. M. Pidgeon in the laboratories of the Canadian National Research Council. A contract with the Defense PlantCorporation was concluded in May 1942 and Magnesium Reduction Co., a wholly owned subsidiary of National Lead Co., was formed to carry out this project. The capacity of the plant was rated at I0,000,000 lb. of magnesium per year, equivalent to an average production of about 14 tons per day. The Process The process, in brief, is as follows: The raw materials are dolomite and ferro-silicon, 75 per cent grade. The dolomite is calcined, the calcine and ferrosilicon are ground and mixed and the mixture is briquetted. The briquets are charged into tubular retorts of chrome-nickel steel set horizontally in a furnace with the open ends projecting outside the front wall. The retorts are then closed and evacuated. Magnesium is liberated according to then reaction 2(MgOl CaO) + Si = 2Mg + zCaO, Si% It is distilled from the charge and con- densed on a removable sleeve in the throat of the retort. Sodium and potassium, if present, are also liberated, distilled and condensed on a "sodium condenser" in the end of the retort. At the expiration of the distillation period the retorts are discharged and the cycle of operations is repeated. For the rated daily capacity of 14 tons of magnesium there are required approximately 170 tons of dolomite, equivalent to about 85 tons of calcine, and 16.5 tons of ferrosilicon. The retort residue, a bulky powder which at present is waste, amounts to about 87 tons. Choosing the Site The investigation to select the location of the plant was conducted by the Research Laboratories of National Lead Co. This work included geologic and economic surveys of a number of districts, examination of dolomite samples by chemical, spectrographic and petrographic methods and large-scale tests of dolomite from several of the more promising localities. in the last-named tests 2-ton samples were put through the ferrosilicon process in the pilot plant of the Canadian National Research Council, under the guidance of Dr. Pidgeon. The conclusions drawn from the investigation, in regard to the quality of dolomite to be used in the ferrosilicon process, were: First, the dolomite should contain not less than 21 per cent MgO and not more than 2 per cent acid-insoluble material. Second, the dolomite should

Jan 1, 1944

By O. Mellgren, A. M. Gaudin, P. L. De Bruyn

The adsorption density of ethyl xanthate on pyrite was determined as a function of xanthate concentration. Surface preparation of the mineral appears to have asafunctionsome effect on the subsequent adsorption process, A monolayer of xanthate on the surface is exceeded only in presence of oxygen. The effect of OH- , HS- (and x and CN- S=)and on the amount of xanthate adsorbed was investigated. Competition between OH- and X- (xanthate) ions for specific adsorption sites is indicated over a wide pH range. IN the flotation of sulfide ores, xanthates are most commonly used to prepare the surface of the mineral to be floated so that attachment to air takes place. The quantity of agent required to make the mineral hydrophobic is usually very small, of the order of 0.1 to 0.25 lb per ton of mineral. Details of the mechanism of pyrite collection are for the most part unsettled. Adsorption of collector has long been believed to involve an ion exchange mechanism as demonstrated for galena' and for chalcocite.2 In the work on chal-cocite it was also demonstrated that a film of xanthate radicals unleachable in solvents that dissolve alkali xanthates, copper xanthate, or dixanthogen was formed at the surface of the mineral. The unleachable product increased with increasing addition of xanthate up to a maximum corresponding to an oriented monolayer of xanthate radicals. Pyrite is extremely floatable with xanthate if its surface is fresh.9 ut the floatability decreases rapidly as oxide coatings increase in abundance. Pyrite shows zero contact angle when in contact with ethyl xanthate solution at pH higher than about 10.5;4 at neutrality, a contact angle of 60" is obtained at a reagent concentration of 25 mg per liter. Alkali sulfides and cyanides are pyrite depressants. In this study of pyrite collection the writers have sought to relate measured xanthate adsorption to the method used in preparing pyrite, to the presence or absence of oxygen, to concentration of hydroxyl, hydrosulfide, sulfide, and cyanide ions. The principal experimental tool has been radioanalysis," " using xanthatcx marked with sulfur 35. Experimental Materials Pyrite: Unlike most sulfides, pyrite is a poly-sulfide. The structure given by Bragg7 resembles that of sodium chloride, the iron atoms corresponding to the position of sodium and pairs of sulfur atoms corresponding to the position of chlorine. The edge of the unit cell in pyrite is 5.40 A and in halite 5.63 A. The S-S distance in pyrite is 2.10 A; the Fe-S distance, 3.50 A: and the Fe-Fe distance, 3.82 A. Natural pyrite from Park City, Utah, was used in this investigation. Pyrite 1 was obtained by hand picking pure crystals. Pyrite 2 and Pyrite 3 were obtained from finer textured crystalline material containing inclusions of silicates. The same cleaning technique was utilized for the preparation of Pyrite 2 and Pyrite 3, whereas a different cleaning technique was used for Pyrite 1. Pyrite 1 was prepared as follows: The crystals were ground in a porcelain ball mill and the 200/400 mesh fraction was separated by wet screening with distilled water, followed by washing for 1 hr with deoxygenated distilled water acidified with sulfuric acid to pH 1.5. The acid was removed by rinsing with deoxygenated distilled water on a filter until a pH of 6.0 was reached in the effluent. This filtration was carried out under nitrogen. The sample was then dried in a desiccator under nitrogen. The period of time for which this pyrite sample was in contact with water containing oxygen was about 4 hr. The specific surface as determined by the BET gas adsorption method was 582 cm2 per g. Final material assayed 53.12 pct sulfur and 46.5 pct iron (theoretical, for FeS,: S, 53.45 pct; Fe, 46.55 pct). After crushing, Pyrite 2 and Pyrite 3 were washed with 1 M HCl. rinsed, and fed to a laboratory shakinq table to remove the small amount of silicates. The concentrate obtained was ground in a laboratory steel ball mill. The 200/400 mesh fraction was separated by classification in a Richards hindered settling tube. This fraction was then given a final wash with 0.1 M HCl and deoxygenated water was filtered through the sample. The final effluent showed a conductivity equivalent to that of a solution having a salt concentration of 0.3 ppm. Aqueous hydrogen sulfide solution was then added to the sampln (about 100 ml saturated H,S solution to about 1000 g pyrite under a few hundred milliliters of water) which was stored wet under nitrogen. The sample stored in this manner showed no indication of formation of iron oxides, whereas iron oxides appeared

Jan 1, 1957

By R. W. Bartlett

The rates of oxidation of tungsten have been determined at temperatures between 1320" and 3170°C and oxygen pressures to 1 amn using a surface -recession measurement technique. Above approximately 2000°C and 10-6 atm the rate is independent of temperature and can be calculated from gas collision theory assuming a constant reaction probability, e, of 0.06. Oxygen molecules react at surface sites where oxygen atoms have previously chemisorbed. This provides a direct pressure dependence at low pressures but at high pressures tungsten oxide molecule s form an adjacent gas boundary layer which lowers the PO2 at the tungsten surface. A correction for this effect using free-convection theory fits the rate data over the entire oxygen-pressure range from 10-8 to 1 atrn as well as data using O2-A mixtures. Below 10-6 atrn and above 2000°C, e decreases with increasing temperature because of desorption of oxygen atoms. Below 2000°C the rate decreases with decreasing temperature at all oxygen pressures following an apparent activation energy of 42 kcal per mole and depending on (Po2)n with n varying between 0.55 and 0.80. MOST of the previous tungsten oxidation studies have employed gravimetric methods and have been limited to temperatures below 1000°C where the weight loss associated with evaporation of tungsten oxides is negligible compared with the weight gain from oxidation.' At higher temperatures, oxygen-consumption rates have been determined from pressure measurements, usually at constant flow rates, by Langmuir,2 Eisinger,3 Becker, Becker, and Brandes,4 and Anderson.5 The sensitivity of this method decreases with increasing pressure and, with the exception of Langmuir's work, these investigations were confined to pressures below 10-6 atm. Above approximately 1300°C, depending on the oxygen pressure, the rate of oxide evaporation is greater than the oxide-formation rate and the recession of the tungsten surface can be measured optically without interference from an oxide layer. This was first done by Perkins and crooks6 who heated tungsten rods in air pressures from 1 to 40 torr at temperatures between 1300" and 3000°C. The present investigation of the oxidation kinetics of tungsten at high temperatures emphasizes oxygen pressures from 10-6 to 1 atm. This is the range of interest for earth atmosphere re-entry applications of tungsten for which little data were previously available. APPARATUS The apparatus is a modification of the type used by Perkins and crooks.' Ground tungsten seal rods, 6 in. long by 0.125 in. diam, were mounted vertically between two water-cooled electrodes, one fixed and the other having free vertical travel. The movable counter-weighted electrode is prevented from undergoing horizontal displacement by three sets of runners mounted at 120-deg intervals. Electrical contact is made by means of a water-cooled mercury pool. A 24-in. vacuum bell jar having a volume of approximately 267 liters was used as the reaction chamber with the sample holder mounted in the middle of the chamber. Power was supplied from an 800-amp dc variable power supply. Temperature readings were made by means of a Latronics automatic two-color recording pyrometer. With this instrument, corrections for emissivity are not necessary provided the spectral emissivi-ties at two closely spaced wavelengths are equal. Supporting measurements were made with a micro-optical pyrometer corrected for emissivity of bare tungsten and window absorptivity. The micro-optical pyrometer was calibrated against a National Bureau of Standards calibrated tungsten lamp and both pyrometers were periodically checked against the melting points of tungsten and molybdenum using the oxidation apparatus. Above 10-6 atm, pressures were measured with an Alphatron gage calibrated against a McCleod gage. At 10-6 atm, a hot-filament ionization gage was employed. A magnified image of the self-illuminated tungsten rod was formed using a 360-mm objective lens mounted outside the bell jar. When the experiment exceeded 1 hr, the image was focused on a ground-glass plate about 10 ft from the tungsten rod at about X8 and the recession of the thickness of this image was monitored with a Gaertner cathe-tometer. When faster rates were encountered, a 35-mm time-lapse cinecamera with a telephoto lens and bellows extension was substituted for the ground-glass plate and cathetometer. Diameter recession rates were determined from the photograph image projected on the screen of an analytical film reader. EXPERIMENTAL PROCEDURE After installing the rod in the apparatus and cleaning it with acetone, the system was evacuated to 5 1 x 10-5 torr. Before oxygen was introduced,

Jan 1, 1964

By Edward B. Walker, Michel Grosmangin

The geological and economic conditions peculiar to the Greater Oficina area are presented to demonstrate the necessity of a low-cost, well-site method of distinguishing gas-bearing formations. The method of gas detection with the neutron log is briefly discussed and its limitations are explained. A new method is described which consists in running a second neutron log with a larger source-to-detector spacing. Field data indicate that under favorable conditions the larger spacing response is proportionately more influenced by the virgin gas zone than is the shorter spacing response. One important condition is that the gas sands be invaded, with a diameter of invasion equal to about two to three times the hole diameter. The calibration of the longer spacing log is made so that the two logs read the same deflection in shale and in a known water or oil sand. Under such conditions, gas is indicated by a positive separation, i.e., the curve for the longer device is displaced to the right of the curve for the shorter device. Because of the non-linearity of the long spacing response, low porosity formations also show positive separations. In sands with large porosity variations, the gas sands can no longer he located visually. They can be detected on a plot of shorter spacing vs longer spac-ing deflections. INTRODUCTION In the Greater Oficina area of Eastern Venezuela, the rapid and accurate detection of gas from well logs is of primary importance because of a combination of economic, geologic, and operational conditions. Briefly, these conditions are: economic—there is no market for gas at the present time; geologic—a single well may contain as many as 30 or more oil or gas sands for which intervals -to be tested must be selected; opera-tional—first, once opened to the casing through perforations, gas sands are extremely difficult and expensive to squeeze off, and second, gas detection must be rapid because the geologist must decide immediately, at the well, which sand to perforate. During the early period of exploitation in Greater Ofi-cina, when clay base muds were used, sidewall samples, together with electric logs, gave fairly good distinction between oil and gas sands. When exploitation became concentrated on deep fields of poorer sidewall sample recovery, and after the advent of oil emulsion muds, now the standard drilling fluid in Greater Oficina, the regular neutron log became the most reliable indicator of gas. In 1953, R. Norelius devised the dual-spacing neutron technique for gas detection. The dual-spacing neutron log has proved to be highly successful in detecting gas and has been adopted as a regular survey by all of the oil companies of the area. Several hundred dual-spacing neutron logs have been run in Eastern Venezuela and several tests per well are available for positive evaluation of the logs. The findings outlined below are based upon this extensive field experience. GEOLOGICAL CONDITIONS OF THE GREATER OFICINA AREA The Greater Oficina area lies on the south flank of the Eastern Venezuela Basin (Fig. 1). Nearly all accumulations of oil and gas in the area are trapped, in whole or in part, against normal faults. All known oil and gas reservoirs in Greater Oficina occur in the Ofi-cina formation (Miocene-Oligocene) or in the "U" sands. The U sands are the lithologic equivalent of the Merecure group (Otigocene-Eocene), which contains oil in many fields north of Greater Oficina. Most of the petroleum produced in Eastern Venezuela is from the Oficina formation.

Jan 1, 1958

By G. H. Bishop

The kinetics of the inter granular penetration and embrittlement of [100] tilt boundaries in 99.998 pct pure nickel upon exposure to bismuth-rich Ni-Bi liquids have been determined in the temperature range from 700° to 900°C. The kinetics of penetration are parabolic in time at constant temperature over most of the temperature range. In a series of 43-deg bicrystals the rate of penetration is anisotropic with respect to the direction of penetration into the grain boundaries. In lower-angle bicrystals the penetration rate is isotropic. The rate of penetration decreases with tilt angle at 700°C. The activation energy for penetration in the 43-deg bicrystals is 42 kcal per g-atom independent of direction. It is concluded that the intergranular penetration and embrittlement in the presence of the liquid proceeds by a grain boundary diffusion process and not by the intrusion of a liquid film. This was confirmed by a determination that the kinetics of penetration and embrittlement were the same in the 43-deg bicrystals upon exposure to bismuth vapor under conditions such that no bulk liquid phase would be thermodynamically stable. WhEN solid metals are exposed to a corrosive liquid-metal environment, the grain boundaries are sites of preferential attack. Depending on the temperature, the composition of the liquid, and the composition, structure, and state of stress of the solid, a number of modes of attack are possible. This paper reports a study of the kinetics of intergranular penetration and embrittlement of high-purity nickel bicrystals upon exposure to bismuth which, together with an earlier study by Cheney, Hochgraf, and Spencer,&apos; demonstrates that there are at least two modes of intergranular attack possible in the Ni-Bi system. In the study by Cheney et al., columnar-grain specimens of 99.5 pct pure nickel were exposed to liquid bismuth presaturated with nickel in the temperature range 670" to 1050°C. They found that the majority of the boundaries, which were predominantely high-angle boundaries, were penetrated by capillary liquid films, the attack proceeding by a process which will be termed grain boundary wetting. This process occurs in a stress-free solid when twice the liquid-solid surface tension is less than the surface tension of the grain boundary,* i.e., when 2yLs < YGB In this case the penetration of the grain boundary by the liquid occurs at a relatively rapid rate, resulting in the severe embrittlement of a polycrystalline solid. Grain boundary wetting is a common mode of intergranular attack in systems in which the lower melting component is relatively insoluble in the solid, but the solid has an appreciable solubility in the liquid, for example, the Ni-Bi system, Fig. 1. In systems of this type at temperatures above the range of stability of any intermetallic phases, once the liquid is saturated with respect to the solid so that no gross solution occurs, chemical gradients are small, and surface tensions become major driving forces for attack, provided the solid is stress-free. The results of Cheney et al. appear to be typical of those encountered when grain boundary wetting occurs.&apos; Capillary films were observed in the boundaries after quenching from the exposure temperature. The mean depth of penetration increased linearly with time, and the activation energy for the process was found to be 22 kcal per g-atom. In a study of the Cu-Bi system Yukawa and sinott4 found that the depth of penetration of bismuth into high-purity copper bicrystals of orientations from 22 to 63 deg of tilt about (100) at 649°C ranged from 0.05 to 0.25 in. after a 12-hr anneal. This corresponds to a linear rate of 6 to 15 X 10~6 cm per sec. At the same reduced temperature of 0.68 the rate for the Ni-Bi system&apos; was 7 x lo-&apos; cm per sec. In another study of the Cu-Bi system, Scheil and schess15 determined the kinetics of grain boundary wetting in hot-worked commercial rod. While there were several complicating factors present in this study, there is general agreement with the above results. The kinetics of penetration were linear, the activation energy was 20 kcal per g-atom, and at 650°C the rate of wetting was 2 to 5 x 10-6 cm per sec. The rate of wetting in the A1-Ga system6 is somewhat

Jan 1, 1969

By Arthur H. Wilson

INTRODUCTION The stratified deposits of the coal measures are strongly laminated and exhibit a high degree of anisotropy. The stronger rocks in the sequence possess joints and shear planes, the coal itself has a closely spaced cleat pattern, and the softer rocks are capable of flowage. To calculate the general distribution of stress in such a medium by analytical means based on the theories of elasticity is difficult, and has not yet been satisfactorily achieved. Nevertheless, some estimate is required to aid the design of supporting pillars and permit the correct siting of main roadways. This is important when laying out districts for longwall extraction, particularly if the results of previous experience are not available in the area to be exploited. Although elastic stress analyses, including finite element analysis, may not be very appropriate, the basic equilibrium conditions will apply. These, combined with logical deductions based on observed fact, can be used to give appropriate solutions which experience has shown to be capable of giving acceptable results in the design of pillars associated with longwall workings. Constancy of cover load is one of the fundamental equilibrium conditions. When mining below ground, the cover is not removed, therefore the average vertical load after mining must equal the initial cover load. If mining produces a local decrease in load in any particular area, it must be balanced by an equivalent increase in load nearby. Bending moments in the strata above are capable of compensating for the turning moments which this redistribution of load may produce, and the existence of a "rear abutment", much discussed between 1950 and 1960, is not an essential equilibrium requirement. If the distribution of vertical stress is plotted three-dimensionally, then the load on any small element of area 6S will be o.6S, where o is the average stress. This also represents the volume of the "stress envelope" which lies above 6s. By making the individual areas very small and summing together, it is possible to show that the total load on any particular area can be found by calculating the volume of the stress distribution envelope which lies above it. A similar consideration applies to the stress distribution in a two-dimensional situation. If the stress distribution curve is drawn, then the area below any portion will represent the load per unit depth of section. For example, Figure 1 represents the possible stress distribution across a caved waste and associated ribside. If AW is the load deficiency [ ] These loads must balance, therefore area AW = AS, and if one can be deduced, the other will then be known. Attempts have been made to measure stress distributions in the ribside and in the waste. Stress meters in soft rocks such as the coal measures have not proved very effective. Those based on the measurement of strain have experienced difficulty in strata capable of flowage, high modulus stress meters suffer from cross sensitivity, and overcoming to obtain absolute stress is almost impossible. Load measuring instruments left in the waste have also proved largely ineffective, mainly as a result of the difficulties of protecting the leads in a caving environment. Certain logical deductions, however, can be made about the conditions in the waste. CONDITIONS IN THE WASTE Over the area of the waste the surface trough which develops is remarkably consistent, despite the geological variations which occur from coalfield to coalfield. In Britain, an accuracy of 210% is claimed for subsidence prediction based on width of extraction and depth of cover (National Coal Board, 1975). The subsidence in the USA is more variable (Adamek and Jeran, 1981), particularly with respect to the point of inflexion, but the same general pattern occurs. At the shallower depths the somewhat harder roof strata involved in the caving in the USA may suffer less compaction, giving reduced values of subsidence. Subsidence at intermediate horizons below the surface

Jan 1, 1982

By Arcy A., J. G. Davis, D&apos Shock

Results of a pilot operation in the Carlsbad Basin are discussed. After hydrafracing between wells, a block of potash was removed by solution techniques. The distance between frac wells was about 200 ft, the thickness of potash mineralization, 5 ft. By proper manipulation, a feed of concentrate brine was obtained. The ex-periment showed that the thin-bedded potash could be removed by the solution techniques. The details of well construction, method of operation, and removal rates are discussed. Continental Oil Co.&apos;s laboratory research on the fundamentals of potash solution mining has been expanded by means of a series of field tests, and subjects such as well completion and hydraulic fracturing were added to the investigation. Both single-well and multi-well systems were studied in the field work. Discussion Background: The current paper discusses one field test in which potash was solution mined by a two-well system from a thin sylvinite zone. The potential economic value of solution mining evolves from (1) the use of drilled holes and solution techniques instead of excavated shafts and caverns and (2) the ability to mine both land and marine deposits through any type of overburden geology and below conventional mining depths. Recent interest has been focused on potash&apos; and other soluble minerals, such as trona. Solution extraction minerals, such as copper and uranium, are also worthy of important consideration. In addition, many of the techniques are directly applicable to the construction of horizontal underground storage carverns in salt. There are two general approaches to potash solution mining. The first is to mine on a single-well basis, in which the same well bore is used for both injection and production. This method is slow, and the areal extent may be quite limited in other than very thick ore zones. The second, and the preferred approach, is to mine on a multi-well basis in which the solvent is circulated between wells. This technique, if applied in a manner which allows the ore zone to be mined from the bottom upward, results in nearly all the solution taking place from the cavern roof. Salt removal rates, therefore, are very much higher than from a single-well system.l Wells can be interconnected into a multi-well pattern by several means. One is to join single-well caverns in the lower part of an ore zone. Another is to use the hydraulic fracturing techniques developed in the oil fields.&apos; We preferred the fracture approach because of its potential for creating the greatest area of salt exposure. Test Site Description: The field tests were conducted in New Mexico&apos;s Carlsbad Basin, where the potash deposits are flat and uniform over reasonable distances. Here, 12 potash zones are present in the massive Salado Salt section. The specific target was the Third Ore Zone which is about 4 ft thick at our location and about 1150 ft deep. The test pattern was designed in the shape of an equilateral triangle with a fourth well located in the center, 200 ft from each of the vertex wells. This configuration allowed the ore zone to be hydraulically fractured from the center well with good assurance that the fracture would intersect the bore of at least one outside well. Several multi-well test patterns would be available if the fracture connected all wells. Well Completion: Surface casing was set in the top of the Salado Salt at 600 ft to shut off water flows from the surface sands, and the salt section was drilled and diamond-cored to a point below the Third Ore Zone. A drilling fluid made of diesel oil with a small amount of emulsified water was used to drill and core the salt. This fluid was highly successful in preventing enlargement of the drilled hole and in promoting good core recovery. The three outside wells were completed by setting 51/2-in. casing at the base of a streak of anhydrite about 20 ft above the ore zone. Pipe was set high so that the intersection point of the fracture could be detected even if the fracture migrated above the ore zone as it progressed outward from the center well. The center well itself was completed by cementing 51/2-in. casing through the Third Ore Zone. Cement bond logs run on the center well have shown excellent bonding. Fracturing Practice: A mechanical tool was used to cut a notch through the casing and into the salt at a point about 1 ft below the ore zone in the center well. The purpose of this notch was to fix the point of fracture entry into the salt. The fracturing was done with water at injection rtaes as high as 30 bbl per min. The salt parted at 1450 psi; and it required only 5 min for the fracture to reach the well which was 200 ft to the south. It took about 5 min more to reach the other two wells. Caliper surveys were run to locate the point of fracture entry in the three outside wells. The fracture appears to have drifted downward slightly, entering the outside wells at the top of a streak of carnallite 8 or 9 ft below the ore zone. A cross section of the wells selected for the multi-well test is shown in Fig. 1. The figure includes KC1 values based on core analysis and the trace of the fracture plane between the wells.

Jan 1, 1971

By P. A. Farrar, M. D. Silver, K. L. Komarek

Thermodynamic properties of Hf-0 alloys have been determined from 0 to 25 at. pct 0 between 1000" and 1200°K by equilibrating specimens with alkaline metal oxide-metal vapor combinations. Partial molar-free energies, enthalpies, and entropies of oxygen have been obtained and are conzpared with similar results for the Ti-0 and ZY-0 In continuation of a thermodynamic investigation of the Ti-O and Zr-O systems1 activities of oxygen and lattice parameters of Hf-0 alloys have been deter- system. The positional entropy in all three systems corresponds to an ideal random interstitial solution with one interstitial site per one metal atom. The lattice parameters of hafnium and Hf-O solid solutions have been determined in the range 0 to 20 at. pct O from measurements of Debye powder patterns. mined. All three metals dissolve large quantities of oxygen to form interstitial solid solutions. The phase diagram of the Hf-O system is shown in Fig. 1.&apos; The maximum solubility of oxygen in the cph a phase is considerable (up to 25 at. pct O). The solubility in the high-temperature phase is much smaller. The only stable compound in the solid state is HfO2 which may exist with a certain oxygen deficiency. The low partial pressure of oxygen of Hf-0 alloys required the application of an indirect method. As the most suitable procedure a method, first applied by Kubaschewski to the V-O system,3 was combined with a principle developed by Herasymenko for the

Jan 1, 1963

By D. E. Marks, Arnold, C. W, R. J. Robinson, A. E. Hoffmann

The efficiency of operation of a fixed-bed adsorption unit is infEuenced both by the absolute adsorption capacity of the bed and by the rate of adsorption. This paper describer studies of adsorption rate which were conducted in an experimental unit designed such that conditions existing in the treatment of high-pressure natural-gas mixtures could be duplicated. Variables investigated included pressure, temperature, gas composition, adsorbent particle size, depth of packed bed and gas velocity. The adequacy of a simplified mathematical model for predicting the observed phenomena was tested. A correlation is preserited which relates adsorption rate to the process variables stlldied. This correlation is useful in combination with the matheinatical model. INTRODUCTION Of the techniques available for contacting adsorbent particles with fluid streams to be treated, fixed-bed adsorption columns offer definite advantages in simplicity and ease of operation. As a result, they are often used in preference to others for such petroleum industry applications as dehydration and purification of natural gas and hydrocarbon recovery. Fixed-bed adsorption units usually consist of two or more towers filled with a desired adsorbent and operated in a cyclic manner. While one is being used to process the main flow stream, the others are undergoing regeneration to remove the adsorbed phase. When the tower on stream becomes saturated with the preferentially adsorbed material, the roles of the towers are switched, and the freshly regenerated tower is placed on stream. Cacle duration is determined by the bed capacity under the process conditions and by the flow rate through the bed. The sharpness of separation which can be effected is a function of both the absolute capacity of the bed and the rate of adsorption in the bed. The effect of rate for a particular set of conditions is evidenced by the sharpness or diffuse-ness of the adsorption front as it advances through the bed. Since data needed for design of adsorption units to treat high-pressure natural-gas systems were not available, an experimental program was designed to investigate the effects of different variables upon adsorption rate in fixed beds. In the present paper, effects of gas composition, column length, temperature, pressure, adsorbent particle size and flow rate (actual linear flow rate of the gas) are shown, and utility of a simplified mathematical model for describing the process is discussed. As gas enters the top of a cool, clean bed of adsorbent, preferentially adsorbed materials are stripped from the main flow stream by the uppermost particle layers. As these layers become saturated with a particular component, new supplies of this component are carried further down the column until fresh adsorbent is encountered. An adsorption wave thus moves through the column as material is supplied to saturate succeeding elements of the bed. Adsorption from a Multicomponent gas stream occurs as a succession of such moving waves corresponding to the different components in the gas. The leading edge of an adsorption wave for a component of a natural-gas stream moving through a bed of a common commercial adsorbent such as silica gel would be sharp but for the influence of certain broadening fac tors. These factors include a nonuniform velocity profile in the bed, longitudinal dispersion or mixing in the main gas stream, and the time required for a molecule to migrate from the main gas stream and be adsorbed at a site within the body of an adsorbent particle. If packing is uniform and the ratio of column to particle diameter is greater than approximately 15:1, the first factor is relatively unimportant&apos; Longitudinal mixing is of importance only for the case of moderately high mass transfer with extremely slow flow rates.&apos; The sharpness of an adsorption front, therefore, is, primarily a function of the rate of adsorption or the time required to saturate a particle of zdsorbent. Two methods for defining adsorption rate are used in this work. The first is a normalized or relative rate which describes the rate of saturation of a differential element of the packed bed. This can be measured by observing the time required for the concentration of the preferentially adsorbed material in the effluent gas from the bed to rise from zero to a value equal to that in the inlet gas stream. The second definition describes the absolute rate of mass transfer from the gaseous to the adsorbed phase. This definition is used in a mathematical description of the adsorption process. If the concentration of a component in the gas strcam leaving an adsorption column is measured and plotted as a function of time, a curve such as that shown in Fig. I results. It is seen that for a period of time the effluent gas is devoid of the component under consideration. As the bed approaches saturation, a small percentage of this material will appear in the effluent gas. The concentration will then rise with time, or increasing cumulative gas flow, until it is equal to that in the inlet gas stream. If adsorp-

By J. G. Bouwkamp

This paper presents three general approaches towards the solution of the stress distribution and the behavior of tubular connections as used in offshore well drilling structures. First, the possibilities of using plastic models and photoelasticity techniques in evaluating the stress distribution in gusset plate connections are analyzed. The results of photoelastic studies on the stress distribution in the in-plane gusset plate of two-dimensional joints are presented. The influence of the configuration of the gusset plate (with and without cut-outs) is discussed. Second, the paper deals with recent developments and applications of computer programs to analyze connections with directly inter-welded tubes and with gusset plates. The possibilities and limitations of these programs are discussed. Stress patterns analyzed with these programs are presented for different joint configurations. Finally, the basic test procedures and results of a test on a tubular joint under static and alternating loads are discussed. INTRODUCTION The effective design of tubular connections as encountered in offshore well drilling towers or floating platforms has been complicated basically by the radial flexibility of the tube walls. This flexibility is a source of severe stress concentrations which can initiate an early failure of these joints. In an attempt to reduce the influence of the wall flexibility of the column tube, certain joints are presently designed by inter-welding the incoming branch members. In those designs, the force acting normal to the chord tube can be reduced considerably. A second group of joints incorporate gusset plates or stiffening rings to stiffen the column wall and to distribute the incoming branch member forces over a larger part of this wall. A third approach to improve the stress distribution in a tubular joint is to increase the wall thickness of the column member. This can be achieved by simply applying a thicker wall section in the vicinity of the joint. A fourth possibility to restrain the radial flexibility of the tube wall is to fill the column member with concrete. Also, a single, cast steel seat welded to the column tube can be used to improve the stress distribution in this wall. Although all these designs improve, in general, the state of stress in the column wall, the altered stiffness often causes the development of critically stressed areas in the web members. At the same time the actual design in most instances is decisively influenced by the site which governs the depth and controls the forces produced by waves, earthquakes and ice flow. Also, the towing, erection and foundation requirements of offshore structures can affect the actual design selection. Because of the complexity of the structural configuration of tubular joints, the stress analysis of these connections has necessarily been based on simplified and often crude assumptions. For the earlier and smaller type of connections with about 4-ft diameter column sections, the primary problem was to evaluate the relative stiffness of the column wall section and the load transfer between joint members. Due to the recent developments of offshore drilling structures with increasingly larger connections (e.g., column diameter. 32 ft; web members, 8.5 ft) this problem has become even more critical. One design philosophy for such large joints follows a member-to-member connection with radially heavy reinforced column sections. This radial stiffness can be attained by closely spaced and intensively stiffened horizontal diaphrams together with vertical stiffeners. A second solution incorporates a concrete-filled section between the outer and inner walls of the column tube. Another philosophy considers large gusset-plated joints. The problem in these joints is to develop an effective load transfer between the branch tubes and the gusset plate and to minimize the stress concentrations in the member walls as effectively as possible. Several concepts are followed to achieve this gradual transfer between web-member walls and gusset plates. Because the number of joints in these huge platforms is limited compared to the over-all size, a proper design of these joints is even more important than was the case for the many joints in the smaller, but multi-legged towers. A failure of one of those ultra-large joints could well cause the complete collapse of such a structure. Under these circumstances an accurate analysis of the large joints is of the greatest importance, together with information regarding the expected behavior of such joints under critical alternating load conditions. Recent applications of photoelastic model techniques have proved to be quite effective in evaluating the elastic behavior of such joints. Although a complete study of such connections is quite well possible with present-day photoelastic techniques, it might often be feasible and necessary to limit the objectives and to restrict these investigations to the study of a specific aspect of the joint. Another very promising avenue of approach to solve the complex stress pattern in these connections seems to be the recent development of digital computer programs. In this category, cylindrical shell programs and finite element methods for more complex configurations have

Jan 1, 1967

By Claude P. Heiner

mountain region to M tht Coast points for domestic consumption and for export are shown in Table 11. There is considerable disparity in rates from both Rock Springs, Wyo., and Castle Gate, Utah, to the four coast cities where the slack coal is to be used for purposes other than export. The rate on coal to be exported is the same from either starting point to any of the four coast cities even though there is a difference of as much as 341 miles in the shipping distance. It is interesting to note that the freight rate between Sunnyside, Utah, and Fontana, Calif., on coking coal is $5.05 per ton and that coal up to 8 in. can be moved on this rate if it is suitable for coking. This rate was published late in 1942 on a contemplated annual movement of more than 500,000 tons. There have been decreases in freight rates since 1923 on movements of slack coal from Utah into Seattle and Portland due to pressure on the railroads and to greater. quantity of coal shipped. It is the author,&apos;, opinion that a movement of slack coal in excess of 3 million tons of coal per year from Utah to any point in central California would justify a freight rate equal to that puhlished for Fontana, Calif.. or $5.05 per ton. The movement of 3 1/2 million tons of coal per year on the basis of 240 mine working days per year would require that 14,600 tons be handled each mine working day. If it is assumed that shipments could be arranged for a 6-day week, the average railway movement would he 11,200 tons, or approximately 3 trains containing fifty-five 70-ton coal cars per day. Such movements of coal would require railroad equipment represented by the investment amounts stated in Table 12 and entail the services of 250 men. Table 12 ... Railroad Equipment and Investment Required To Move 11,200 Tons of Coal a Day from Utah to California Railroad Equipment Cost 2800. 70-ton coal cara at $6.000 each $16,800.000 32 locomotives at $310.000 each. 9.920.000 Miscellaneous eauiument:.......... .5;000:000 Total........................ $31,720,000 It therefore appears that, under presently known mining methods, the lowest price at which coal could be sold f.0.b. the mine in amounts of 3 1/2 million tons per year for generation of power in central California would be $4.60. It also appears that the lowest freight rate that could be expecled between intermountain points and the central California area would be $5.05 per ton, making a total cost of coal delivered at a plant site of $9.65 per ton. Conelusions The following are the author&apos;s conclusions: 1. Coal mines in Utah and in the Kemmerer and Rock Springs districts of Wyoming could increase annual production by 6 1/2 million tons per year. 2. Under present conditions coal could probably be delivered to any steam electric plant in central California at a price not to exceed $9.65 per ton. 3. The use of coal at such a price, while higher than the equivalent present price of fuel oil, is entirely feasible. 4. There are adequate railroad facilities for movements of large quantities of coal from the intermountain region to the Rest Coast. 5. In a national emergency it probably would be extremely difficult, if not impossible, to obtain sufficient oil to meet requirements of the greatly expanded West Coast steam electric generatsing capacity. 6. The intermountain region contains ample coal reserves to supply all conceivable demands for West Coast power generation for a number of generations. 7. Increasing demands of labor threaten to lessen, if not eliminate, savings in cost of coal production through the use of new mining machinery. 8. Continuation of experiments in socialism by the Federal Government through construction of hydroelectric generating plants, particularly those unrelated to land-use reclamation, defies justification. Rates under this concept of a governmental function are subsidized through greater taxation of its people. Private capital is available to construct steam plants, or hydro plants where feasible, and should be permitted to continue in order to preserve the principles of our free enterprise system. DISCUSSION (L. C. McCabe and Robert P. Koenig, presiding) C. C;. BALl*—I was asked to lead off the discussion, but it is not with the thought that I might be able to add anything to the paper. The thoroughness with which it was prepared rather forestalls the asking of many questions. Your treatment, Mr. Heiner, is a very valuable contribution. I do want to suggest—that although you have limited your study to this specific question, with certain geographic limitations, many of the things in your paper apply just as well to the eastern coals. I want to agree 100 pct with your final conclusion concerning government-subsidized construction. Id. C. McCabe*—It is certainly worthwhile to take stock occasionally to see where we are going in problems of this nature. I agree with Mr. Heiner that ultimately the only reliable source of fuel that the West Coast has is coal hut the time factor is the difficult element to evaluate. Just before I came here I discussed this subject with N. B. Hinson, Vice President and Executixe Engineer of the Southern California Edison Company, and Chairman of the West Coast Inter-Power Exchange Committee. He has given much thought to utilities&apos; fuel supply and it was very helpful to me in preparing a discussion of the paper to talk with him beforehand. Stock taking and forecasting of future development are essential to the continuing success of any enterprise. Mr. Heiner has called attention to the unprecedented growth of central and southern California and to the increased demands for fuel and power which have accompanied it. He discusses the increased fuel oil and natural gas requirements and the probable limits on the future use of these fuels and of hydroelectric power. In contrast to the calculable limits of these sources of electric energy, the author points to the availability of enormous reserves of coal in the Rocky Mountain States adjacent to the Pacific Coast which can be utilized for power generation. That there will be increased use of coal for power generation in the area under discussion is generally accepted hut it is in the timetable of such development that there is not complete agreement. In a recent report, Mr. Hinson reviewed the future power outlook for the Pacific southwest area. He pointed out that the use of steam plants in connection with water power plants in this region has made the maximum use of hydroelectric energy possible, and that the correct balance between hydro and steam generating plants produces the most economical overall system. Steam plants in the area which had been installed to protect against deficiency in hydro energy in dry years were used to carry war loads. Fortunately, no dry

Jan 1, 1950

By William J. Gillich, Gerald L. Moss

PREVIOUS studies of the shock loading of randomly oriented polycrystalline aggregates have firmly established that, after rather short load duration, hydrostatic compression closely approximates the shocked state.&apos; However, McQueen deduced from pressure measurements with good time resolution that, during shock loading, metals begin to undergo a stress relaxation at the yield stress. He suggested that the relaxation is due to plastic deformation accompanying the change from a one-dimensional compression to a three-dimensional, hydrostatic, compression.&apos; Stress relaxation may occur faster as stress is increased above the yield stress, but the existence of unidirectionally compressed states for finite times suggests that the concept of a unidirectionally distorted lattice should furnish considerable insight into the mechanical behavior of materials subjected to shock loading. Here, a crystallographic analysis is presented for the hypothetical situation where atom motion may be considered as unidirectional which, as indicated above, is a useful extension of the macroscopic concept of shock loading to the microscopic domain. Only motion caused by the com-pressive forces is treated; i.e., lattice vibrations upon which this motion is superimposed, as discussed by Fitzgerald, are ignored.3 The purpose of the analysis to be presented is to develop a description for single crystals of the lattice rotations that occur for idealized uniaxial strain deformation. The usefulness of such an analysis in realistic deformation is to give a method of specification of those properties of an initially distorted lattice which would affect the subsequent deformation. Non-axial complications that arise experimentally, such as off-axis rarefaction waves, must be treated in proper context. Consider the material element shown in Fig. 1 and let the compression be uniform at all regions of the element. Then, any interior point of the element is displaced in proportion to its distance from the base of the element. Accordingly, if the top of a unit element is displaced by an amount, (-K), with respect to the base, a point P(X, Y) will be displaced by (-KY). Crystal planes are, therefore, rotated by the compression. Analysis of this rotation may be accomplished from the geometry shown in Fig. 1 where the line OP is the edge of the plane {hkl} and N is its normal. The orientation of the crystal plane with respect to the shock direction is specified by the angle, before deformation. After deformation the edge of plane {hkl}

Jan 1, 1969

By J. A. Ede

The object of the writer is to call attention to a rather unique aggregation of economic products distributed over a line of succeeding formations about 3 mi. long, to be seen within a few miles of La Salle, Ill. Fig. 1 is an ideal section of the stratification exposed and exploited along a distance of 3 1/5 mi. in a southwesterly direction from the quarry of the Utica Hydraulic Cement Co. located near the historic site of Kaskaskia village to the Oglesby shaft at Oglesby. No attempt has been made to cover the whole field, special mention only being made (with the exception of two places) of the operations found along the course or parallel to the direction assumed in the ideal section. I have used Fig. 2, after J. R. Bent and De Witt Kelly, to locate the relation of the La Salle anticline to the coal mines of this district and to show the operation of No. 1 and 3 mincs of the Illinois Zinc Co. Anticline and the Rock Formations Owing to the structural deformation between La Salle and Utica, the older rocks of the state are exposed to the surface along the northern embankment and the bottoms of the Illinois River valley near the latter place. At; the Illinois Zinc Co. works, Sec. 16, Tp. 33, R 1, a well for water mas sunk 1828 ft. and samples taken every 10 ft. of the ground penetrated; duplicates were sent to Mr. Cady of the Illinois Geological Survey. A general compilation or synopsis study of this section is here presented. As the well is over 1 mi. west of the Western limb of the anticline, the section affords some reliable data. These samples were studied and interpreted by H. M. DuBois as Lower Magnesian, and by G. H. Cady as the Lower Magnesian. The results are given in Fig. 3. The most interesting geological feature of this district is the La Salle anticline. In 1865, Leo les Quereux, looking at Split Rock, asked how it happened that the upper coal measures overlie strata of the Lower Silurian and what has become of the formations which are generally found intermediate—the Upper Silurian, the Devonian and sub-carboniferous, and the lower member of the coal measures?

Jan 1, 1920