Search Documents

By R. I. Jaffee, F. C. Holden, H. R. Ogden

The mechanical properties of Ti-C and Ti-C-0 alloys can be altered by heat treatments to dissolve or reject carbon from solid solutions. The maximum strength is obtained by annealing just below the peritectoid temperature. Quenching from the ß-carbide field results in softening. Impact behavior is influenced by the extent of solution of interstitials CARBON is not as important in titanium alloys as it was in earlier years when graphite induction melting was more prevalent. With induction melting, carbon pickup is about 0.5 to 0.8 pct. Cold-mold arc melting with graphite electrodes, which is among the more current methods, results in carbon pickup of 0.1 to 0.2 pct. The titanium-sponge melting stock itself contains about 0.02 to 0.07 pct C, picked up from the magnesium used in the reduction process. Thus, carbon is still one of the more important contaminants in titanium and needs careful study and evaluation in order to understand titanium and titanium alloys. Moreover, it is equally proper to consider carbon as an alloying addition because, in controlled amounts in titanium alloys, it may serve a most useful function. This is particularly the case where the ultimate in toughness is not required. The addition of carbon to titanium results in a peritectoid-type system as illustrated in Fig. 1. The solubility of carbon is seen to be higher in the a phase than in the ß phase in the temperature range of interest. Below the peritectoid temperature, the solubility of carbon in a titanium decreases with decreasing temperature. This type of system permits many microstructural and heat-treatment variations which may influence the properties of the alloys. The study of how the microstructure variations affect mechanical properties is described in this paper. Experimental Procedures The experimental techniques and testing methods used in this work were the same as those described in detail in a previous paper.' No further descriptions will be given except where changes have been made. High purity iodide titanium, produced by the New Jersey Zinc Co., was used in all of the alloys. Carbon additions were made using high purity spectro-graphic carbon electrodes in order to obtain the highest purity carbon available. The alloys were prepared by double arc melting to reduce the possibility of segregation. The alloys were forged at 875°C to ¾ in. round, descaled, vacuum annealed for 5 hr at 900°C to remove the residual hydrogen, and swaged to ¼ in. round at 750°C. All heat treatments were made on material in this initial condition. Two of the early Ti-C ingots were found to have been contaminated in melting. Vacuum-fusion analyses showed that the two contaminated alloys had picked up oxygen, so the test results on these two alloys permitted an evaluation of ternary Ti-C-0 alloys. A list of the alloys and their compositions are given in Table I. Properties of Ti-C Alloys In a peritectoid-type system, such as the Ti-C system, the chief microstructural variable which influences the properties is solid-solution strengthening. For a given composition, it is possible to control the disposition of carbon, either in solid solution or as the compound Tic, by suitable heat treatments. When in solid solution, the carbon present in the alloy makes a definite contribution to the strength of the alloy. However, when present as Tic, it has very little effect on the strength. Other microstructural variables considered in this investigation were transformation structures and grain size. As discussed in subsequent sections, these variables have only a minor effect on properties as compared to the solid-solution effect. Solid-Solution Strengthening: The principal strengthening mechanism for Ti-C alloys has been found to be solid-solution strengthening. Carbon in interstitial solid solution strengthens titanium, but has very little strengthening effect if present as the compound. Since carbon has a higher solubility in

Jan 1, 1956

By Norman Patton

THE subject assigned is so broad that thorough discussion is well-night impossible within the space allotted, and further, few specific data are available upon which to predicate conclusions concerning the efficiency of present methods of distributing anthracite. This paper treats briefly the various agencies through which both primary and secondary distribution are effected, the methods of transportation and the general interrelation of production, demand, inventories and price. AVENUES OF DISTRIBUTION "Three distinct types of primary distribution are common in the marketing of anthracite. First, though not most important, is the sale by the producer, or operator, direct to the consumer. These sales, other than to employees and the local trade, are generally confined to steam sizes for industrial uses, and are consigned to the sidings or docks of the consumer. Sales of this type often are so closely priced to compete with oil and bituminous that the addition of even a small dealer's margin is sufficient to increase the cost to the point where the business might be lost. Second, the operator sells to a wholesaler or broker for subsequent resale, either to a retail dealer for clearance through his yard or direct to large consumers. Usually this method of distribution is employed by the smaller operators, who do not find it economically feasible to maintain extensive sales organizations. In most instances, the wholesaler retains some 5 per cent for his services, paid, of course, by the producing company whose anthracite he handles. He may, and frequently does, handle the output of several different companies, suited to the varying needs of the

Jan 1, 1935

By Milton E. Wadsworth, J. Brent Hiskey

INTRODUCTION Fifteen years ago a distinguished electrochemist referred to electrochemistry as an "underdeveloped science " In the article in question, Professor Bockris (1) stated that many areas of.natura1 phenomena and applied technology are not perceived as being electrochemically based At that time, this was especially true for much of non-ferrous extractive metallurgy and was a particularly accurate description of hydrometallurgy During the last decade, there has been considerable advancement in applying the theory of electrochemistry to our know1 edge of hydrometallurgical processes and in understanding the mechanisms of underlying electrode reactions. Impressive as these advances are, there is still a growing need for electrochemical research of mineral systems and electrochemical engineering to apply this work in practical situations In a broad sense electrochemistry is defined as the physical chemistry of ions in solution and of phenomena which occur at the electrified interface. Bockris and Reddy (2) refer to electrochemistry as being divided into two fundamental domains, ionics and electrodics ionics is restricted to the behavior of ions in solutions, examples being many familiar redox processes Electrodics represents the main part of electrochemistry, and is the study of charged interfaces and the conditions governing charge transfer reactions across them. Considering hydrometallurgical applications, electrodics suggests the following relationship for a conducting solid (bulk or surface)

Jan 1, 1981

By Charles Hawes

WHEN sulfur is encountered in objectionable amounts, it is regarded as the most trouble-some element for the mine operator to control. It exists in two conditions in iron ores, as sulfide in iron pyrites and as sulfate in gypsum and barite. The sulfate radical (SO,) may also be linked to one or more of the several other elements found in the iron ore compound. The only dependable method for the de-termination of sulfur, particularly when found in the insoluble residue, has been the so-called fusion method. This is a long and tedious process involving several hours for its completion. In looking for a more rapid method which would be .applicable to all iron ores, the writer investigated the work of M. Groger1 who in 1881 showed that by heating pyrite with iron out of contact with air, the pyrite is reduced to iron sulfide and from the latter all of the sulfur will be given off as hydrogen sulfide gas on treat-ment with hydrochloric acid. FeS2 + Fe = 2 FeS FeS + 2 HCl = FeC12 + H2S In 1891 F. P. Treadwell2 not only confirmed the results of M. Groger but also found that iron powder would reduce to sulfide the sulfate radical of any substance, including barite, if not found in excessive quantities. The writer found this to be true and developed a method, in cooperation with F. J. Baker, chief chemist, mining department, of the Cleveland-Cliffs Iron Co., Ishpeming, Mich., for the determination of sulfur in iron ores which is not only very rapid but also accurate. Pure iron ore powder, reduced by hydrogen, gave good results but was found to be very slow in reacting. A high silicon iron with a low sulfur content of 0.012 per cent was found to be. much more active than the pure iron and gave excellent results.

Jan 11, 1927

By J. B. Mudd

Introduction It is difficult to think of any activity on which mankind has been more dependent than mining, and certainly there is much evidence in almost every part of the world of old workings that clearly demonstrate that man from earliest times has dug and toiled to take from the earth precious stones, metals and materials that from time to time have been essential or of value to him. In step with social development and industrial and technological advances the tempo of mining activity, regulated only by the laws of supply and demand, has quickened and in this century has accelerated rapidly in keeping with its dramatic development. Indeed, the rate of change of events has been such that if it were to continue to accelerate as fast as it has over the past decade there is reason to wonder how the insatiable demands for metals and minerals are to be met in the years that lie ahead. Shallow mines containing high-grade ore deposits either have been or are being rapidly mined out and their place can only be taken in general by ore lying at greater depth, or by ore of low grade, situated for the most part in remote and in underdeveloped areas. The cost of exploration and development is rising at an alarming rate, with the result that the expenditure now required to bring a mine to production far exceeds anything previously contemplated. It is estimated that the total capital required to maintain existing operations and develop new ones during the next 5 years will be of the order of $50,000 million and of this, new capital to bring new mines to production will be of the order of $3,000 million. Today no single mining finance company can, from its own resources, find all the money for a major mining development, and as a consequence there has been a strong trend toward joint ventures and to the formation of multinational consortiums. International lending institutions already play an important part in financing many new mining projects and their participation provides the financial umbrella under which other lenders can invest with greater security. There is little doubt that to finance the costly ventures in the future, governments and international lending agencies, banks and finance

Jan 1, 1971

By H. C. Brassfield, R. E. Fryxell, E. C. Duderstadt, E. A. Aitken, P. K. Conn

Permeation rates of hydrogen through are-cast tungsten were measured at temperatures from 1300" to 2600°C with hydrogen pressure differentials of 1 and 0.1 atm across isothermal membranes. Rates were nearly Proportional to square root of pressure, were inversely ProPortional to membrane thickness, and were temperature-dependent according to the equation: p = permeation coefficient in cu cm (stp)-mm per sq cm-min-atmlr2, R = gas constant in cal per mole-OK, T = absolute temperature in OK. Permeation rates of oxygen through tungsten were deternlined in the range 1965" to 2300°C and at calculated oxygen (02) pressures of 3.3 x 10-4 to 2.2 x at?n using sealed capsules containing Kmown quantities of tungsten oxide. Permeation coefficients obtained in this manner had a temperature dependency in the range of 40 to 45 kcal per mole of permeating species. Permeation coefficients for oxygen were higher than those for hydrogen in the temperature range studied. This is probably the result of oxygen solubility being much greater than hydrogen solubility at these temperatures at a gzven pressure. The purpose of this investigation was to determine experimentally the permeabilities of hydrogen and oxygen through polycrystalline tungsten at temperatures ranging from 1300° to 2600°C. Permeation rates of hydrogen through tungsten have been measured at temperatures up to 925°C,but no previous measurements have been reported for the temperature range covered in this investigation. Some diffusion measurements3&apos;&apos; and solubility measurements3 have been made for hydrogen at temperatures below 2200°C. No previous permeability studies of oxygen through tungsten are known to the authors; however, efforts have been made to determine diffusion rates5-&apos; and solubilities PERMEATION THEQRY Permeation has been defined by ortton" as the overall steady-state flow process from the gas phase on one side of a membrane or wall to the gas phase on the other side and includes the steps of adsorption, solution, diffusion, exsolution, and desorption; in a given temperature range, any of these processes may be rate-controlling. For diatomic gases, which dissociate prior to diffusion, the quantity of gas which permeates through a membrane or wall at a given temperature is directly proportional to the surface area of the membrane, the length of time of permeation, and the difference between the square roots of the pressures on each side of the membrane, and it is inversely proportional to the thickness of the membrane when diffusion-controlled, thus: q = total amount of gas permeating a membrane, p = temperature-de pendent permeation coefficient, A = area of membrane exposed, / = time, p i = gas pressure of high-pressure side, p2 = gas pressure of low-pressure side, d = thickness of membrane. When the surface reactions are not rate-controlling steps and the solution of the gas in the metal follows Henry&apos;s law, the permeation coefficient, P, is equal to the product of diffusivity and solubility. The permeation coefficient is also temperature-dependent according to the equation: Po = permeation constant, Q = activation energy, R = gas constant, T = absolute temperature. MATERIALS The tungsten materials used in this investigation were greater than 99.9 pct pure. The interstitial impurities ranged from < 1 to 50 pprn C, 7 to 35 ppm O, less than 15 pprn N, and undetectable quantities of hydrogen. Previous high-temperature studies of are-cast tungsten have shown that thermal treatment similar to that which the hydrogen permeation cells experienced reduces the carbon content from starting levels of 50 to 60 ppm to about 30 ppm. Metallic impurities were in the low (1 to 50) ppm range. The argon gas used in this investigation contained about 8 ppm N. None of the following gases were

Jan 1, 1968

By M. F. Williams, L. G. Hendrickson

IN classification of pulps bearing magnetized ferromagnetic particles, depolarizing is of great importance. If size separation is to be effective, particles must be individual rather than in floes. Depolarizing is also practiced in heavy medium separations in which ferrosilicon or magnetite is the medium. When particles of ferromagnetic material have been removed from a magnetic field, residual magnetism causes agglomeration. The term depolarizing refers to the operation of reducing or eliminating this residual magnetism and may thus be considered magnetic deflocculation. The terms demagnetizing and randomizing are also used. At the Research Laboratory of Oliver Iron Mining Div. in Duluth a method was developed for measuring depolarization of the pulp of ferromagnetic material. Experiments were made with Mesabi taconite,&apos; a natural magnetite of low coercive force. Ferromagnetic materials of higher coercive force, such as lodestone or the artificial magnetite produced by reduction roasting of hematite, present a more difficult problem, which was not within the scope of this investigation. It is possible, however, that some of the techniques evolved for measuring and calculating electrical characteristics of alternating current coils would be of use in depolarizing high coercive force material, particularly in conjunction with high-frequency alternating current, as proposed by Hartig and others.&apos;," Properties of Ferromagnetic Materials:&apos;7 Experimental work, described below, has shown that if a sample in the magnetized state is heated above the Curie point and cooled, much of the preferred orientation is destroyed and the sample is substantially depolarized. It has been thought that when the sample cools below the Curie point the domains cancel each other, leaving a zero net moment. However, such particles still exhibit a tendency to cohere, and undoubtedly this is caused by the forces of residual magnetism. -AS measured by the percent depolarization, this tendency is reproducible for any sample upon repeated heating above the Curie point and subsequent cooling and is independent of the initial state of magnetization. It is postulated, therefore, that as the material is cooled below the Curie point the domains in any particle do not completely cancel each other, but rather are preferentially oriented to some extent. Mechanism of Depolarizing with Alternating Current Magnetic Fields: It is believed that when ferromagnetic material is passed through an alternating magnetic field, depolarizing occurs in the decaying portion of the field. As the particles pass through the portion of highest intensity they become magne- tized. If the particles are not free to move, the polarities of the particles will be reversed (by a mechanism similar to that described above for magnetism) at a frequency equal to that of the applied field. As the material moves through the decaying field, intensity levels become such that a domain does not completely reverse, but stops on an axis of easy magnetization. By the time the material reaches the point of zero field intensity, a state of fairly random orientation of domains is achieved. If conditions are such as to give a completely random orientation, the particle will have little or no external magnetic field, and a pulp of such particles will be depolarized. Previous Work In 1918 E. W. Davis was granted a patent for demagnetization of magnetite pulps.&apos; His method consisted of passing the pulp through a tapered coil, activated by alternating current of normal frequency (60 cycle). This method, with minor modifications, has been used almost universally in all pilot plants and commercial installations in which depolarization of low coercive force materials has been required. Hartig, Onstad and Foot2,3 avd made a detailed study of the factors involved in depolarizing both low (below 100 oersteds) and high (above 100 oersteds) coercive force material. They developed a method for evaluating the relative degree of depolarization of any pulp based on the settling characteristics of the pulp. Their standard of comparison was a sample heated to above the Curie point and cooled in a zero field, all in a neutral atmosphere.* For low coercive force material they found treatment.Thisprocedure is subsequently called, in this report,theCurie that results equivalent to Curie treatment could be

Jan 1, 1957

OPEN-HEARTH refractories are not merely an accessory to the furnace. They are the furnace, to all intents and purposes. The steel work of the main structure is merely an open frame which helps to support the refractories; and the regenerators, a necessary part of the furnace system, consist almost entirely of refractories. Not only do refractories constitute the essential part of the furnace, but they also carry the liquid steel all the way &apos;to the point where it begins to solidify. On leaving the furnace the liquid passes through a refractory runner into a refractory-lined ladle, then through a refractory nozzle closed by a refractory stopper on the end of a rod protected by refractory sleeve bricks. The liquid is sometimes sent through an additional refractory- lined tundish, a supplementary ladle, or a refractory runner for bottom pouring, until it finally enters the iron mold in which it solidifies. Even in the mold, refractory materials are sometimes used to provide a nonconducting "hot top." This series, from runner and ladle to hot top, inclusive, is often referred to collectively as the "pouring-pit refractories." REFRACTORY RAW MATERIALS The raw materials available are best classified into basic and acid types. The principal basic raw materials are magnesite, dolomite, and chrome ore. The principal acid materials are silica in various natural forms, and fireclay. Magnesite. Austria was the principal source of magnesite (MgC03) until recent years, when the Province of Quebec, in Canada, and the states of Nevada and Washington became important sources for the American steel industry. More recently these natural sources have been supplemented by the so-called "sea-water magnesite"-which is the name somewhat incorrectly given to magnesium hydroxide obtained as one of the products

Jan 1, 1951

By A. B. Kinzel

PRECISE knowledge regarding the effect of heat treatment on the properties of steel has made possible the detailed specifications and instructions covering optimum heat-treating temperatures and practices that are in current use. A distinct contrast is presented by the metallurgical treatment of steel adjacent to a fusion weld, as such steel is subjected to each temperature from room temperature to fusion temperature, and cooled at a rate that is not generally controllable but is predetermined by the nature of the assembly to be welded, the kind of welding used, and the surrounding conditions. This is true regardless of the type of fusion welding: oxyacetylene, electric arc, thermit or flash resistance. Therefore it seemed desirable to investigate the effect of this metallurgical treatment on the characteristics of carbon steels commonly used for welding, by a detailed study of metal subjected to each temperature range; i.e., each heat-affected zone. Oxyacetylene welding was chosen for the investigation because of the experimental facility of accurately segregating and studying each temperature zone. The nature of the zones produced by other types of welding is the sane. The difference is primarily a matter of dimensions of each of the temperature zones involved. The advantages and disadvantages of the extent of the zone are of prime moment, and are discussed after the presentation of the detailed zone study. No mention is made of the fused metal proper, as this has been the subject of much published research and the nature of the solidified metal is fairly well known. GENERAL METHOD The scheme of procedure in the work herein reported involved the testing of the metal of each temperature zone adjacent to the weld in so

Jan 1, 1935

By H. A. Wahl, J. M. Campbell

This study extends our information on solid-liquid slurries to the flow of sand in horizontal fractures. Inasmuch as this is basically an unsteady-state process, a comprehensive photographic study was undertaken in a 10-ft windowed cell to determine if the basic flow regimes described for steady-state flow in pipes applied to the subject process. Since the number of potential variables far exceeds the capacity of a single study, emphasis has been placed on the effects of sand concentration, oil viscosity and oil flow rate. The extensive photographic evidence obtained has proven very valuable in gaining an insight into the basic flow mechanisms. Being able to follow visually the flow characteristics that accompany the quantitative data is valuable in the application of the results. Although the use of dimensionless parameters was carefully investigated. it was found that the data obtained could be more easily, and as accurately, correlated by judicious use of the dimensional variables investigated. However, a study into the feasibility of scaling slurry flow was made in the event this technique is justified in future investigations. The data presented show that the pressure behavior observed in solids transport in pipes basically applies to slurry flow in horizontal fractures. The roles of the parameters are altered but a basic equivalence exists. The most significant correlating parameter was the oil viscosity (µo) and the bulk velocity of the slurry (vn), expressed as &apos;&apos;µv" product. The most significant correlation expresses the rate of advance of the sand as a function of the variables investigated. There are many practical ramifications of this phase of the investigation that should aid in better treatment design. Evaluation of sand advance rates provides a means of estimating sand placement efficiencies during a treatment and the resulting sand distribution in the fracture. The results show that sand placement efficiencies are low under typical treatment conditions. A brief description of the effects of overflushing is also included. INTRODUCTION The flow of sand-oil slurries in fractures is an area in which little basic knowledge is available. This stems to some degree from the fact that it is impossible to duplicate fractures at the surface. They occur in various shapes and sizes with an infinite combination of irregularities. Unfortunately, we can never "see" these fractures except in cores and by indirect means of measurement. In spite of this inherent difficulty, it is desirable to develop some basic concepts that will provide a better understanding of the sand transport mechanism. An insight into the problem is provided by investigations of fluid flow in rectangular conduits. Several studies on the flow of liquids in non-circular conduits1,13 show that a Reynolds number-Fanning friction factor relationship can be written if the hydraulic diameter is substituted for the regular diameter in a circular pipe. This hydraulic, or equivalent, diameter is taken as four times the cross-sectional area occupied by the flowing fluid divided by the wetted perimeter. Eq. 1 expresses an extension of this same work when applied to infinite parallel planes b distance apart.&apos; Eq. 1 is a theoretical equation expressing the friction factor as a function of the Reynolds number for laminar single-phase fluid flow. This expression has been verified experimentally. The equivalent expression for a smooth circular conduit differs only in that the value of the constant is 16 instead of 24. Numerous studies have related friction losses to Reynolds number in both circular and non-circular conduits. These results are widely used and are not reviewed here. Huitt&apos; investigated the effect of surface roughness on fluid flow in simulated fractures. He concluded that fluid flow in fractures may be treated similarly to fluid flow in circular conduits. This work, together with that of Nikuradse,&apos; shows that surface roughness has no appreciative effect upon the resistance to flow in the viscous flow region. In the region of turbulent flow, surface roughness is a prominent factor. Hydraulic conveyance literature is another important source of information. Durand3 has attempted to organize systematically the variables involved in hydraulic-solid transport in pipes. He has classified the modes of flow into three types according to the size of the particles in the mixture— homogeneous mixtures, intermediary mixtures and heterogeneous mixtures. With the usual concentrations and flow rates used in hydraulic transportation, particles with diameters of less than 20 or 30 microns form eszentially homogeneous mixtures with water. The data show, however, that even small materials will tend to settle out under laminar flow conditions. Mixtures containing solids over 50 microns in diameter do not achieve total homogeneity even under turbulent flow conditions. Particles from 50 microns to 0.2 mm in diameter may be transported in fully suspended flow at normal transport velocities although the concentration in the vertical plane is not uniform. Above 2 mm in diameter solid materials are transported along the bottom of the conduit at a velocity substantially less than that of the liquid itself. Between 0.2 and 2 mm in diameter, the particles tend to be in a transition zone between heterogeneous suspended flow and deposit flow at normal hydraulic transport velocities. The sand sizes used in fracturing usually fall in this size range. It is interesting to note that the grain size range designated by Durand for this transition zone corresponds closely to the transition zone between

By John W. Frey

[Minerals, generally of great geological age, are to a very large extent the material basis of what we know as modern civilization. In most of the so-called civilized world the use f minerals has become such a commonplace that it is easy to se sight of their importance. It was the use of minerals, obably more than anything else, that made it possible for e American people to expand from the Atlantic seaboard the Pacific in a little over one hundred years. As the 1 to use the natural wealth at hand constitutes a funda¬ental element in American life, there seems to be justification for the thought that American geography is largely mineral geography. Of all American environmental reactions, the most striking are those which have come about through the use of the metals and the power fuels. If we turn to the ancient industry of agriculture, we find very little that is unique in North America except those developments which have come about through the use of machinery and transportation, both of which are contingent upon the use of minerals. Practically every crop now grown n North America was grown in some part of Europe before merica was discovered. One can point out exceptions to statement but in general it is true. Analysis of the es of North American agriculture shows that the outstand¬ characteristics are: regional specialization (i.e., the Economic Geographer; Chief, Petroleum Section, Minerals Division, u of Foreign and Domestic Commerce.]

Jan 1, 1932

By Oliver C. Ralston

This paper reports the results of the use of salt in some research work carried on during the past 3 years at the Salt Lake City Station of the Bureau of Mines, which is quartered in the University of Utah, whose Metallurgical Research Department cooperates with the Bureau. Only the work involving the use of salt is described. The authors wish equal credit given to J. F. Cullen, C. L. Larson, C. Y. Pfoutz, C. E. Sims, H. C. Neeld, R. W. Johnson, F. G. Moses, N. C. Christensen, and G. H. Wigton, who have all in some way contributed toward the success of this work, while connected with the station in one way or another. Lead Metallurgy Popularly Supposed to be Without Problems In lead metallurgy it is difficult at first to find metallurgical problems, as the prevailing conception has been that lead is so easily concentrated in its various ores and so easily reduced to its metallic form that the only progress possible is that involved in cheapening methods of mining and of reduction. Most of the problems usually considered are of minor nature and do not involve radical metallurgical changes. During the three years of work of the Salt Lake Station, the following classification of problems in the metallurgy of lead has been made: Oxidized Ores. 1. Ores containing only lead. 2. Ores containing lead and silver or gold. 3. Ores containing lead and zinc, with or without silver. Sulphide Ores. 1. Ores of pyrite carrying some lead. 2. Ores of complex zinc-lead-iron sulphides. 3. Complex sulphides containing precious metals.

Jan 1, 1918

By R. W. Waterfill

MANY existing ore deposits of valuable metals have been worked out in their upper surface levels and the continued productivity of these mines is dependent on their extension to greater depths in the earth. The maximum depths at present reached are about 6000 to 8000 ft. below the surface, with no evidence of an impoverished ore vein. These mines are widely distributed; some of the best known are in South Africa, Brazil, India and in the western sections of the United States. Among the factors which increase the difficulty of working these mines at increasing depths are hoisting, rock pressure and temperature. The manner and effectiveness with which these problems are met will, no doubt, determine in a large measure the ultimate depths to which any mine can be profitably worked. The most critical of these three factors at present is the increase in temperature with depth. The high temperature and humidity in many of these mines at present is severely detrimental to the health of the workers and greatly hampers their efficiency. Some have almost reached a condition in which the human system cannot survive. The problems involved in the cooling and ventilation of mines have all been ably analyzed and presented in previous articles. For this reason, only a resume of conditions affecting the cooling and conditioning of deep and hot mines will be given in this paper before attention is directed to possible methods of improving atmospheric conditions in the working levels.

Jan 1, 1929

By W. R. Johnson, M. Hansen, John M. Parks

AS part of a research project sponsored by the Signal Corps Engineering Laboratories, which had the objective of obtaining a magnet wire of good conductivity and low temperature coefficient of resistance, a comprehensive literature survey, supplemented by experimental work, revealed that a linear relationship exists for solid-solution alloys between the electrical conductivity, K, and the temperature coefficient, a, as expressed by the equation: k = a/ß where ß is constant for the solvent metal and a - per°C. tR0 It has long been known that the electrical conductivity at a given temperature and the temperature coefficient of resistance of binary alloys are related to their constitution by the LeChatelier-Guertler rules, as illustrated by Figs. 1 and 2: Rule 1—In alloy systems consisting of a heterogeneous mixture of two phases, the electrical conductivity and temperature coefficient vary as a straight line, if the composition of the alloys is given in volume percentage, Fig. 1. Rule 2—In solid solutions, the electrical conductivity and temperature coefficient are always lower than those of the solvent metal, and usually a considerable decrease occurs with the first small percentage additions of the solute metal, Fig. 2b. If the two components form a continuous series of solid solutions, the electrical conductivity and temperature coefficient curves take the form of a U-curve, Fig. 2a. That some kind of proportionality exists between electrical conductivity and temperature coefficient of resistance is implied by the LeChatelier-Guertler rules and by study of data such as those given by Smith and Palmer,&apos; Fig. 3. Dellinger2 in 1910 first recognized this relationship in a number of commercial copper wires, ranging in conductivity from 94 to 100.7 pct I.A.C.S. He gave the ratio of temperature coefficient to the percentage of conductivity as a constant, C = 0.003939. A year later, Lindeck observed that the linear relationship was valid for a wider range of conductivity in "various sorts of copper," and concluded that the product of resistivity and temperature coefficient was 6.78x10-5 1.5 pct. Since then, this relationship seems to have been entirely ignored. Conductivity-Temperature Coefficient Relationship If the electrical conductivity of copper solid-solution alloys with phosphorus, silicon, arsenic, antimony, aluminum, nickel, manganese, and iron is plotted against the temperature coefficient of these alloys, the diagrams in Figs. 4 and 5 are obtained. Similar data were found with copper-rich solid solutions containing magnesium, cobalt, and titanium,&apos;" as shown in Fig. 6. In all cases, a linear relationship exists. The point representing the highest

Jan 1, 1952

C. W. GOODALE, Butte, Mont. (member of the committee)- (communication to the Secretary*).-In the discussion of papers presented at the New York meeting of the Institute in February, 1915, and at the Arizona meeting of September, 1916, I referred to the activities of the Bureau of Safety of the Anaconda Copper Mining Co., and I am now submitting a few thoughts by members of the staff of that Bureau. TORGUS H. OAAS, Safety Engineer, Butte, Mont.-The report of the Committee on Safety and Sanitation has described different organizations and methods of promoting safety work. The effectiveness of these methods would aid the beginner in his campaign for safety in choosing the kind of organization and methods best adapted for his field. This can he obtained only by a discussion by those who have long promoted this kind of work, and have met with successful results. As the field is new, the different organizations promoting safety work have not established a common basis of rating for their fatal, serious and slight accidents, so that it is now difficult to get a comparative basis from which to judge the merits of the different systems. C. W. GOODALE.-The U. S. Bureau of Mines adopted, at the beginning, as a basis for its yearly summaries, the number of accidents. per 1,000 men employed, and it is now (quoting from its report for 1915, Technical Paper 168) making the following "classification of injuries:" "Many of the States now have. compensation laws, and in order to conform with their classifications, the bureau&apos;s classification of serious and slight injuries for 1915 is on a 14-day (2-week) basis instead of 20 days, as in previous years. The new classification of injuries includes three types, as follows: 1. Fatal 2. Serious (time lost, more than 14 days) (a) Permanent disability Total Partial

Jan 6, 1917

By Franz Wever

The importance of the Widmanstätten structure to structure theory in metallography has been recognized by many writers.l It is a structure produced by the precipitation of a, new phase from a solid solution upon cooling as a result of changing solid solubility, and displays a characteristic appearance indicating a crystallographic relationship between the new phase and the original solid solution (Fig. 1). First discovered in 1808 by Alois de Widmanstätten2, the structure has been traced by analogy through many alloy systems. Particularly is this true of the steels. Sorby&apos;s classic work3 on the microstructure of iron and steel was in essence an attempt to explain the origin of this characteristic structure in meteoric iron. He observed in a Ressemer steel and in a cast-steel ingot structures which we now recognize as typical Widmanstatten figures.4 Osmond Observed structures in a steel ingot analog-ous to those found in meteorites. Arnold and Mc William6 obtained (and recognized) a

Jan 1, 1931

By William E. Ford, Edward Salisbury Dana

THIS Appendix contains a series of tables, more or leas complete, of minerals arranged according to chemical composition or to certain prominent crystallograhic or physical characters. These, it is believed, will be of service not only to the student, but ago to the skilled mineralogist. The type used in the printing of the mineral names indicates their relative importance. Table I is a complete list of the species named in this book arranged fist according to the prominent basic elements which they contain and secondly according to their acid radicals. Table II is of Minerals arranged according to their System of Crystallization The other tablets make no claim to completeness, being limited often to common ah important species. For an exhaustive system of Determinative Tables based particularly upon blowpipe and chemical characters, the student is referred to the work of Professors Brush and Pen- field, mentioned on p. 330.

Jan 1, 1922

By J. H. Fletcher

AIR has been cooled, heated, washed; humidified and dehumidified for many purposes and in many industries. At a number of metal mines air is conditioned to reduce the high humidity and unbearable heat found in deep workings, and at some mines air is washed to allay siliceous dust. Steam is introduced into the intake air at many coal mines, particularly in winter, for the purpose of keeping loose coal dust so moistened that the hazard of an explosion is lessened. This paper will describe a further successful application of air conditioning in a coal mine, where, for over three years, all intake air has been cooled to a constant temperature for the sole purpose of preventing roof falls.

Jan 1, 1931

By Alfred H. Bell

The year 1936 in Illinois was marked by considerably increased activity in drilling, both wildcat and proved territory, in leasing, and in seismic and geologic exploration. Of the 92 oil and gas wells completed during 1936 in Illinois, 49 were oil wells, 3 were gas wells and 40 were dry holes. This compares with but 34 completions in 1935. The total of the daily initial productions of the new oil wells was 1755 bbl., or an average of 36 bbl. per well. One new field was discovered, the Bartelso field in Clinton County. The leasing of some large blocks of acreage in Clay, Marion, and other counties by the Carter Oil Co. in the late fall of 1935 was followed in 1936 by extensive leasing in southern Illinois by 10 major companies and many smaller companies and individuals. It is estimated that 2½ million acres were under lease by the end of 1936. Seismograph surveying has been carried on by about seven companies, and the number of seismograph parties operating in Illinois has varied from six to eight throughout most of 1936. It is estimated that approximately two million dollars has been spent in the state in seismic and geologic exploration and in leasing during the last quarter of 1935 and all of 1936. Production of crude oil in Illinois in 1936, according to the Bureau of Mines, was as follows: Barrels Barrels January...................... 325,000 July........................ 402,000 February..................... 294,000 August..................... 380,000 March....................... 396,000 September.................. 386,000 April......................... 347,000 October.................... 393,000 May......................... 389,000 November.................. 363,000 June......................... 383,000 December................... 387,000 4,445,000 This 4,445,000 bbl. was an increase of 3 per cent over 1935. Although this increase was due largely to the fact that production was not artificially curtailed, it also reflects some new production and some increases in production from repressuring and water-flooding, which offset the

Jan 1, 1937

By Brian J. Gorval, Robert L. Kemeny

INTRODUCTION Financing, or providing adequate capital at low cost for developing and bringing a natural resource property into production, is a fundamental requirement for profitable operation. Under the present economic environment the cost of financing any project is gaining more importance than ever. The fundamental keys for success in mining are "the Four M&apos;s": Mineral, Market, Management and Money. In recent years, with capital and operating costs skyrocketing, increased emphasis on obtaining adequate and low cost capital funds for bringing in a prospect is essential. For a small mining company there are limited sources for raising funds. In most cases these companies have neither a substantial asset base, nor any cash flow, and they are deemed as risky investments. The issue of shares of capital stock of such a company is probably the most common method of raising funds via the public purse. Alternatively, debt could be used and a source of such capital might be private investors or financial institutions. The company which intends to raise funds from the investing public by way of the sale of equity, subsequently lists those shares for trading on a stock exchange. Going and staying public commits a company to a multitude of complex laws, rules and reporting requirements. The governing bodies are the watch dogs for the public. The largest of such an organization of this kind in the world is the Securities and Exchange Commission (SEC) in the United States. In Canada, the Securities Laws come from within provincial jurisdiction. Most provinces have their own Securities Act, and Securities Commission. It is the Commission which administers the Act, and hence controls the distribution and trading of securities within the province. Extra provincial registration is required for trading and distribution in more than one province. In British Columbia, prior to a public offering, the approval of the Superintendent of Brokers (SOB) and of the VSE must be obtained. THE VANCOUVER AND TORONTO STOCK EXCHANGES There are five stock exchanges in Canada which supply a trading forum in which mining companies may operate. The stock exchanges are located in Montreal, Toronto, Winnipeg, Calgary, and Vancouver. Of the five stock exchanges, the Vancouver Stock Exchange (VSE) and the Toronto Stock Exchange (TSE) are the most heavily used for resource-based issues and are the focus of this paper. The objective of this section is to provide a brief background on the VSE and TSE. The Vancouver Stock Exchange The VSE is Canada&apos;s predominant stock exchange for financing resource-based, junior issues. Since 1907, the VSE has acted as a source of funds for mining, exploration and energy companies throughout Canada and the world. Currently, there are over 1400 companies listed on the VSE. During 1983, over 3.1 billion shares traded at a value exceeding CDN$3.96 million. The VSE has developed a reputation as one of the few exchanges where a speculative resource venture may obtain a listing and subsequent financing in a relatively short time, generally five to ten months. The SOB, the Investment Dealer&apos;s Association of Canada (IDA), and the VSE all regulate trading at the Exchange. Any irregularities in a company&apos;s stock dealings are investigated and trading may be halted by the VSE until a satisfactory explanation has been received from the suspended company. Companies can be suspended from trading or delisted for various reasons. One reason is misrepresentation of facts in documentation submitted to the SOB, VSE, or to the public, through news releases.

Jan 1, 1985