Search Documents

By R. D. Russell, R. M. Farquhar

ISOTOPIC tracers have become an important aid in following the progress of chemical processes in the laboratory. It has recently been found possible to utilize a system of naturally existing isotopic tracers to obtain information about the geo- logical history of lead ores. Common lead, such as is found in lead deposits, is a mixture of four stable isotopes having atomic weights 204, 206, 207, and 208. Of these, the last three are identical with the lead isotopes produced as stable end products of the radioactive decays of uranium and thorium: the first, lead-204, is not known to be produced on the surface of the earth by any process. Since uranium and thorium occur in the surface regions of the earth in amounts comparable with lead, and since the half-lives of uranium and thorium isotopes are of the same order as the age of the earth, they produce the radiogenic lead isotopes in amounts com- parable to the amount of nonradiogenic lead present. Every significant exposure of a sample of lead to uranium and thorium will therefore lead to the permanent alteration of the lead isotope ratios in that sample.

Jan 5, 1957

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ranaome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3Y4x41/4-in. tool joints; 8-in. bits, 23/4x 3 3/4-in. tool joints; 6-in. bits, 21/4x31/4-in. tool joints; 4-in. bits, 15/ix25/s-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 2-in. drill pipe with tool joints, 31/2-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 to 37/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect' and by Chapman in a report on the San Manuel Copper Deposit.' The rocks are well-consolidated Gila conglomerate, quartz monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Rannome. In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 31/4x41/4-in. tool joints; 8-in. bits, 23/4x 33/4-in. tool joints; 6-in. bits, 2Y4x3Y4-in. tool joints; 4-in. bits, 15/ix25/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property. To allow for 23/8-in. drill pipe with tool joints, 31h-in. core barrels and bits were used. With the standard 31h-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 55/8 to 3 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven machines. The open churn drill hole was cased with 21h-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in un-consolidated material like the formations drilled by

Jan 1, 1953

By Patricia J. Rand, Kailish Narayan

Atlantic Richfield Co. began operating a commercial uranium solution mining project in April 1975, in Live Oak County, Tex., 10 miles southwest of the town of George West. The operation is designed to produce 250,00 lb of U308 per year and is jointly owned by Atlantic Richfield Co., Dalco, and U.S. Steel. The proprietary process employed in this operation consists of injecting an alkaline leaching solution into the ore-bearing formation through a pattern of injection wells. The uranium-bearing solution is then removed through producing wells using submersible pumps in central production wells. The produced solution is pumped through a pipeline to the plant area where the uranium is extracted. The barren solution is refurbished and returned to the pattern area for reinjection. The injection field and plant site are located in the drainage of Spring Creek, a small intermittent stream tributary to the Nueces River. Land use in the area is primarily agricultural cattle ranching and farming---but several producing gas fields are present in the areas as well. A nine month enviromental baseline study was conducted on the property beginning in Feb. 1975. Plants and animals of the Clay West area were identified and representative terrestrial and aquatic communities were analyzed. Physical and chemical parameters of the soils were described and analyzed. The surface and underground waters were analyzed chemically; radionuclides, heavy metals, nutrients, and pesticide concentrations were measured in the creek sediments; bacteriological measurements were made in creek water and sediments; radionuclide and chemical levels in plants and animals, both terrestial and aquatic, were measured. These studies, though not required by existing, state or federal laws, were considered necessary to assess the existing conditions before operations began on site. The in-place leaching technique for uranium mining eliminates the enviromental disturbances associated with open pit or underground mining. No grinding and crushing of ore is needed, nor are large tonnages of waste tailings produced. Surface subsidence is not expected since less than 5 lb of uranium is present per ton of rock and even complete removal of such small amounts should not cause subsidence. Solution mining has fewer environmental problems than conventional mining. Members of the Texas Water Quality Board recognized the differences which exist and have recently formulated new environmental control procedures which apply specifically to solution mining. Some of the solution mining activities which are of particular concern are discussed in the following pages. Process Description The produced uranium-bearing solution is pumped through a pipeline from the pattern area to the plant area. The first pattern area consists of a nest of 125 fluid injection, production, and monitor wells [(Fig. 1)]. Injection wells have 4-in. casings and are spaced 50 ft apart on a square grid. Production wells have a 6-in. casing and are located in the center of each square. A block flow sheet of the plant is given in [Fig. 2]. The produced solution goes through parallel trains, each consisting of a carbon column and an ion exchange column in series. The carbon column removes any sand present in the produced solution and the ion exchange column extracts the uranium. The depleted solution is treated with chemicals and returned to the field for reinjection. The uranium retained in the ion exchange column is removed periodically with a sodium chloride solution. Uranium-bearing solution from the ion exchange column is passed through a charcoal column for removal of impurities and then to a precipitation tank where the uranium is precipitated as yellowcake slurry. The yellowcake slurry is clarified, filtered and dried to produce a granular yellowcake product. Environmental Considerations Sources of waste solutions to storage reservoirs, the backwash reservoir and atmospheric discharges are shown in the block flow sheet [(Fig. 2)]. These waste solutions pose a relatively small problem and are adequately controlled by conventional means. There is one area, however,

Jan 1, 1978

By J. H. McCarthy, J. M. Botbol, R. B. McCammon, G. H. Gott

Four areas have been identified as favorable drill site locations for determining whether a suspected porphyry copper deposit exists in Rowe Canyon, NV. Favorability is bated on the similarity to a deposit model constructed from geochemical data for the porphyry copper deposit near Ely. Favorability is defined as the coincident number of positive anomalies for zinc, silver, aresenic, antimony, and iron. The favorable areas coincide with an observed magnetic high and areas in proximity to major faults.

Jan 1, 1983

By W. J. Feuerstein

STRUCTURAL imperfections in crystals, in recent years, have received the attention of metallurgists concerned with single-crystal properties. Certain etching solutions cause local variations in the rate of etching at dislocations.' Dislocations are expected to be preferred segregation sites for impurities' and Dash" has shown that precipitation of copper occurs preferentially at edge-type dislocations in silicon. Diffusion rates along dislocations are probably higher than rates through more perfect crystalline regions.' These and other phenomena which may be influenced by dislocations may be studied by revealing dislocations as etch pits. This study was undertaken to develop an etch solution for silicon crystals to reveal low-angle grain boundaries associated with dislocation arrays and also etch pits with good contour definition. Additional etches have been reported by Dash," Vogel and Lovell.T rystals were sectioned on crystal lographic planes at various angles from the growth direction for microscopic examination of the etch pits. Experimental Crystals of 75-100 g mass and 3 cm diam were oriented and cut on crystallographic planes. Crystals were grown by Czochralski technique from a quartz crucible. Lapped wafers were chemically polished in a modified CP-4 etch for 1 min (bromine was deleted from the etch solution). The polished wafer was then etched* at room temperature for 5 min. The use of larger amounts of H2O and/or CH2COOH slows the reaction. The Cu(NO3),.3H2O was added to increase the reaction rate and give more definition to the etch pits developed. Some pertinent features concerning the attack of this etch on silicon can be summarized as follows:

Jan 1, 1959

THERE are three chief production zones of tungsten ore in China. In the Province of Kiangsi mines are located at Kanchow, East River, and West River. Their combined production is understood to amount to 300 to 350 tons of ore per month, and their original exportation is made through the port of Kiukiang, largely to Shanghai. The second zone is in Kwangtung Province, the mines there being at Tayulin. Produc-tion reaches about 200 tons per month and cargo is gen-erally exported through the port of Hong Kong. In the Province of Hunan approximately 25 tons of ore are produced monthly in the mines at Ton-on. Tungsten ore from Kiangsi and Kwangtung Prov-inces is generally about 70 per cent WO, (tungstic acid), while that from Hunan is of lower quality, run-ning about 65 per cent WO3. Kiangsi ore is received from the mines in 100-1b. and Hunan in 224-lb. gunny sacks. No repacking is done except as it is made neces-sary by the condition of the sacks. Kiangsi Province contains the Chinese districts pro-ducing the largest amount of salable wolframite or tungsten. Many districts west and south of Kiangsi have been found to have wolframite deposits.-Com-merce Reports.

Jan 1, 1928

By R. G. Treuting, W. C. Ellis

The twinned state is characterized by a lattice of coincidence sites. Imperfections are required at stable lateral twin interfaces. Twinned regions can occur with relative ease in the diamond cubic IN recent contributions1,2 on the origin and growth of cubic annealing twins, attention has been directed to the orientation relations between such twinned components and their parent matrix. There are some aspects of twinning which may be illuminated by a more detailed consideration of the twinned state" alone. As an extreme example, the dense twinning in cast ingots of germanium,&apos; as contrasted with the rarity of twins in cast face-centered cubic metals, is yet to be accounted for. It has been this that has led us to the present work, which, it will be noted, uses methods and constructions in many respects similar to those of Kronberg and Wilson.&apos; In the cubic systems, a 70" 32&apos; rotation about a <110> axis is angularly equivalent, as to twinning, to the more usually considered 180" rotation about a <111> axis. Figs. 1 and 2 show a (110) projection of a twinned face-centered cubic lattice and a twinned diamond cubic lattice. In both figures, the two adjacent planes A and B, shown by the larger and smaller circles, are sufficient to represent the entire array. In each case a section of lattice, the original atom sites of which are shown by open circles, has been rotated as indicated through 70" 32&apos; to bring an original. [112] direction into coincidence with the [112] diiection. The latter is the intercept on the (110) projection of the (ill) plane normal thereto, the twinning plane. In the face-centered cubic case the rotation can be performed about an axis passing through an atom-site; the mirror plane then is also a composition plane containing atoms common to both twinned and untwinned lattices. The diamond cubic lattice may be construed as two interpenetrated face-centered lattices. Its (111) planes recur in a sequence of alternately short and long interspacings. Consequently a mirror plane for twinning cannot be a composition plane, but must be the bisector of one of the spacings. When the longer spacing is selected, the closest distance of approach across the mirror plane in the [ill] direc- tion is identical with that in the untwinned structure. In each case periodically recurring (ill) planes (parallel with the twinning plane) are found, on which there is coincidence of atom sites of the pre-twinned and twinned orientations; these are indicated by the cross-hatched circles. In the face-centered lattice there is such coincidence every third (ill) plane; in the diamond cubic lattice, on two adjacent planes in every six. At the twinning interface in the latter, there is on each side of the mirror plane a (ill) plane of atoms common to both twin components. Conceivably, there is little influence on a plane of atoms about to be adhered to such a pair of coincidence planes, whether it be laid down in a normal or in a twinned position with respect to the previously formed structure. Slawson% as attributed the high incidence of twinning in diamond to this boundary state. Further examination shows that the motion of intermediate planes can consist of various pairs of equal and opposite translations, for example of (ill) planes in the [l&apos;;i2) direction, the familiar twinning shear, indicated in the small schematics in the figures. Since the translations form a system of shears of alternating sign between coincidence planes, twinning could take place by such a mechanism over an extended region without extensive shear; in fact, in this case any atom moves but the distance in the [1i2] direction. One alternative construction for the face-centered cubic lattice leading to the same end result is illustrated in Fig. 3. The plane (711) with respect to the pretwinning orientation (the twinning plane of Fig. 1) is given, the twinned region arbitrarily bounded by <110> and <112> directions. The coupled shear is identical to that of Fig. 1. The "rotational" movement about coincidence sites generating the same twinned position could consist as shown of the translation a,/d% for each atom of a group of three in the B layer in a different one of the three <112> directions, and a similar translation of the underlying three atoms in the C layer in either the same or the opposite sense. This is not dissimilar to Kronberg and Wilson&apos;s construction for their 22" rotation of three adjacent (111) planes.

Jan 1, 1952

By W. A. Vine

When a hole is made in a stressed solid, such as rock pierced by mine openings, equilibrium of the solid is destroyed. To restablish that equilibrium the stress condition in the rock surrounding the opening becomes rearranged. This rearrangement may or may not develop local stresses in the vicinity of the opening which exceed the elastic strength of the rock. Since stability of the opening depends, therefore, on the strength of the naturally occurring rock surrounding the opening, this rock is an engineering material of construction, and all rock affected by the associated opening or system of openings may be considered a structure. The term invert is chosen to describe the formation of the structure built from the inside, as it were, and a consequence of mining rather than an entity built for a purpose. By definition, an invert structure is formed when openings are made underground and is com- posed of that material on the solid side of a rock-air interface wherein the stress condition is affected by the associated opening or system of openings. The shape of an invert structure is never clearly defined; the skin of the structure may be mapped, and even described, but the boundary of the structure within the solid rock mass must be arbitrarily set.

Nov 1, 1955

By A. L. Mular

lnput energy-size modulus relation at small reduc-tion ratios is expressed by Et = (M, -Mt) k;. In some cases 13 is close to Schuhmann&apos;s distribution modulus a in value. Experimental results in conjunc-tion with the equation demonstrate the fact that energy input which produced fracture is not expended on unbroken starting material inside the mill at any time. Recently, schuhmann1 derived the Charles equation2 using the postulate that complex com-minution operations can be considered as a summa- tion of many comminution events. The fragments resulting from each event are assumed to follow the Gaudin-Schuhmamn distribution. In his derivation, Schuhmann implies that the size distribution of the total mass of a material is determined by the fraction of that mass actually subjected to comminution. Consider a feed to contain a volume, Vo, of uni- formly sized homogeneous material. After t seconds of grinding, let the volume of broken material be Vo - Vt where Vt is the volume of starting material not yet broken. The size distribution of the broken material is given by: where V is the cumulative volume less than size X, and k, is the size modulus of the broken material at time t. The distribution for the total volume at this

Jan 1, 1962

By D. L. Albright, G. A. Colligan

An investigation has been conducted to determine the nature of the crystallographic substructure of nickel and a 1.0 wt pct Ag-Ni alloy which had been undercooled 105°C prior to solidification. A rotating back-reflection X-ray technique and modified Weissmann diffractometer were used to orient single-crystal sections from these poly-crystalline ingots and to determine the substruc-tural features of these single crystals, The sub-grain size in the pure nickel ingot is 0.5 mm diam while the silver-doped nickel subgrain size is only 0.1 mm diam. The misorientation between adjacent subgrains is approximately 1 deg of arc in both ingots, and the spread of orientation of sub-grains about the mean orientation of the crystal is 5 deg of arc in both ingots. The addition of silver results in a stable impurity substructure which is preserved during isothermal solidification and subsequent cooling to room temperature. In the absence of silver the initial impurity substructure is destroyed by dislocation interactions which produce a secondary substructure which grows to a size five times larger than the initial substructure. THE process of undercooling a metal entails cooling of the molten sample below the equilibrium freezing point without the occurrence of solidification, i.e., by exercising proper constraint over the experimental variables contributing to nucleation in the melt. The current work of walker1 and Colligan Metal reports undercooling large continuous samples of nickel by imposing appropriate restrictions upon the parameters of solidification. The silver-nickel equilibrium diagram3 reveals the presence of a monotectic reaction at 1435°C. At this temperature the maximum solid solubility of silver in nickel is approximately 3 wt pct, but this solubility decreases with decreasing temperature and the solute is rejected as a silver-rich liquid phase at temperatures below 1435°C. Thus, the 1.0 wt pct solute should be held in solution during undercooling and solidification and subsequently precipitate as a silver-rich liquid phase at grain and subgrain boundaries following solidification during cooling below 1435. This assumes no solute segregation sufficient to cause the monotectic reaction. One would expect this second phase to inhibit grain and subgrain growth by retarding dislocation motion after solidification is complete. The effectiveness of silver addition in growth retardation of high-angle grain boundaries has been demonstrated by Colligan and suprenantS4 The principal [l00] dendrite growth directions in a 2 wt pct Ag-Ni alloy undercooled 53 all radiated from the nucleation site. A similar pure nickel ingot undercooled 59°C exhibited a random orientation of [l00] dendrite directions with respect to the nucleation site. Since undoped nickel ingots do not retain any evidence of the casting or solidification texture and silver-doped ingots do retain this texture, it is reasonable to assume that considerable grain growth has taken place in the pure nickel. These particular experiments were performed in order to reveal the differences, if any, in the features of the crystallographic substructure of undoped undercooled nickel and silver-doped undercooled nickel. 1) EXPERIMENTAL PROCEDURE Data are reported on selected specimens from two massive (approximately 260 g) undercooled ingots of nickel. One ingot consisted of electrolytic nickel and the other of this same material with 1.0 wt pct addition of high-purity silver. Powder patterns were taken of both the as-received and as-solidified materials; in all cases the reflections recorded were attributable to the individual elements nickel and/or silver. Fig. 1 is a. schematic diagram of the apparatus employed for the undercooling experiments. The equipment consists in part of a fused silica crucible for containing the charge. A fused silica tube encloses the system, which is covered by a brass cap to permit partial sealing of the inert atmosphere. This cap contains a hole through which a Pt-Pt 13 pct Rh thermocouple is inserted for temperature measurement. The charge is inductively heated under a purified argon atmosphere.

Jan 1, 1963

By E. F. Reed

CONSIDERABLE deep hole prospect drilling has been done in the last few years in the Globe-Miami mining district about 70 miles east of Phoenix, Arizona, and in the San Manuel-Tiger area about 50 miles south of the Globe-Miami region. More than 205,000 ft of churn drilling have been completed by the San Manuel Copper Corp. at their property in the Old Hat Mining District in southern Pinal County. The deepest hole on this property is 2850 ft; there are 49 holes deeper than 2000 ft. At the adjoining Houghton property of the Anaconda Copper Mining Co., where only one hole reached 2000-ft depth, there were 27,472 ft of churn drilling and 3436 ft of diamond drilling. Three churn drill holes were deepened by diamond drilling methods. Near Miami in the Globe-Miami district the Amico Mining Corp. drilled four holes by combined churn and rotary drilling methods, the total amounting to 13,879 ft, of which 2256 ft were drilled with a portable rotary rig. In the same district, besides doing a large amount of shallow prospect drilling, the Miami Copper Co. drilled two holes of 2560 and 3787 ft, respectively, which were completed by churn drilling methods. The rocks encountered in drilling at San Manuel and Tiger are described by Steele and Rubly in their paper on the San Manuel Prospect&apos; and by Chapman in a report on the San Manuel Copper Deposit? The rocks are well-consolidated Gila conglomerate, quartz , monzonite, and monzonite porphyry. In some places these formations stand very well while being drilled, and three holes were drilled without casing, the deepest of which was 2200 ft. In other holes faulted and fractured ground made drilling difficult. In the Globe-Miami district the deep drilling was done in the down-faulted block of Gila conglomerate east of the Miami fault and in the underlying Pinal schist. The geology of this area is described by Ransome.3 In the Amico holes the conglomerate varied from material consisting entirely of granite boulders and fragments to a rock made up of schist fragments in a sandy matrix; in the Miami Copper Co. holes there were more granite boulders and the material was poorly consolidated. Drilling was much more difficult and expensive in the Miami area than in the San Manuel district, mainly because of the depth of the holes and the formations drilled. All the deep hole prospecting described in this paper was done with portable rigs. The churn drill rigs were of several types, of which the Bucyrus-Erie were the most popular. Bucyrus-Erie 28L, 29W, and 36L rigs were used on some of the deeper holes on the San Manuel property. A few Fort Worth spudder types were tried, and the deepest hole at San Manuel was drilled with a Fort Worth Jumbo H. The spudder type is considerably larger than most other rigs used on this work and required a larger location site. The spudders were belt-driven machines with separate power units, and time required for setting up and moving was much longer than with the more portable drills. All the churn drilling was done by contractors or with machinery leased from them. A few of the contractors had complete equipment, including most of the necessary fishing tools. Unusual and special, fishing tools were obtainable from the supply companies in the oil fields of New Mexico or in the Los Angeles area. Most of the contractors used equipment with standard API tool joints, so that much of it was interchangeable. Failure of tool joints is one of the principal causes of fishing jobs. It can be minimized if the joints are kept to the API specifications and the proper sized joints are used in the various holes. The minimum sizes that should be used with various bits are as follows: 12-in. and larger bits, 4x5-in. tool joints; 10-in. bits, 3 1/4x4 1/4-in. tool joints; 8-in. bits, 2 3/4x 3 3/4-in. tool joints; 6-in. bits, 2 1/4 x3 l/4 -in. tool joints; 4-in. bits, 1 5/8 x2 5/8-in. tool joints. Two rotary drill rigs were tried at San Manuel on the same hole, and a portable rotary drill rig was used on the Amico drilling for test coring the formation and for drilling in holes 3 and 4. Rotary drilling differs from churn drilling or cable tool drilling in that the bit is revolved by a string of drill pipe and the cuttings are removed from the hole by a thin solution of mud pumped through the drill pipe. The principal parts of a rotary rig are the power unit, a rotating table to revolve the drill pipe, hoists to raise and lower the pipe and to handle casing, and a pumping system to circulate the drilling liquid. The rig used on the Amico property at Miami was mounted on a truck. The larger rig used on the San Manuel property was hauled by several trucks and had separate turntable and pumping units. Diamond drill coring equipment was used successfully with the rotary rig in the holes on the Amico property, To allow for 2 3/8-in. drill pipe with tool joints, 3 1/2-in. core barrels and bits were used. With the standard 3 1/2-in. core barrel there was considerable difficulty in maintaining circulation with mud, so a barrel was designed with a smaller inner tube and a broad-faced bit. This allowed coarser material to circulate between the barrels. Rock bits of 5 5/8 to 3 7/8 in. were used with the rotary rig for drilling between core runs. Diamond drill equipment is much lighter than churn drill tools, so that fishing tools can usually be obtained from supply houses by air express when needed. Three churn drill holes on the Houghton property at Tiger were deepened by diamond drilling with Longyear UG Straitline gasoline-driven-machines. The open churn drill hole was cased with 2 1/2-in. black pipe. In deep hole churn drilling, casing is one of the most important items, especially in drilling in unconsolidated material like the formations drilled by

Jan 1, 1952

By Leonard Grimshaw

THE idea of bonding two dissimilar ferrous metals, and making use of both, is an old one. Tips have been brazed onto tool shanks for many years. The bonding of larger pieces to form whole bars and sheets has also been accomplished, but has received little attention in the technical literature, although a number of patents have been issued covering various methods for its accomplishment. There are three main motives behind the manufacture of composite steels. One is that the physical properties of one steel may supplement those of another; a useful, but at the same time, hard, brittle steel may be backed by a soft ductile one, or a stainless steel may be backed by a steel possessing greater strength. Another motive is direct lowering of cost; an expensive steel may be backed by a less expensive one, bringing down the cost of the piece as a whole. The third motive is an indirect lowering of cost, as when a useful steel is backed by a steel that is easier to machine, so that machining cost on a finished product is lowered considerably. Often more than one of these motives lead to a decision to use a com-posite steel.

Jan 1, 1936

By E. H. Bunce

CONTINUED progress in zinc metallurgy has been shown during 1933 by the adoption of new methods as well as the modernization of old processes and equipment, and by the initiation of new fields of activity for future advancement. The use of suspension roasting continued to grow as its advantages and adaptability became increasingly, apparent. The process developed by the National Smelting Co., Ltd., several years ago, of completely roasting on large sintering machines with utilization of the gas for acid manufacture has worked so successfully that an additional machine was installed during the year. At both the Swansea and the Avonmouth Works all of the ore for smelting is now roasted on the large sintering machines, thereby completely eliminating the old hearth-roasting furnaces. Work continued on obtaining partial purification of zinc ores from lead and cadmium by close control of conditions on the sintering machine, and in a few instances by chlorine additions to the ore before sintering. Ores so treated were either partially roasted or com-

Jan 1, 1934

By R. W. Hertzberg, R. W. Kraft

A study of the fracture behavior of unidirectwn-ally solidified Cu-Cr eutectic alloy was performed. Fractured whiskers, grain boundaries, and the interface between proeutectic Cr dendrites and the Cu matrix were the predominant failure initiation sites where grain size was larger. Strain induced void formation was restricted at lower solidification rates. This was attributed to a lack of adequate plastic constraint and a probable preferred orientation. A modification of the Crussard et al. model is presented to explain the appearance of "elongated dimples" on the shear fracture surface. A Cu-Cr alloy containing about 1.8 at. pct Cr solidifies by a eutectic reaction forming filamentary crystals of chromium within a continuous copper solid solution matrix.&apos; Webb and Forgeng2 have shown by bend tests that the extracted chromium filaments, which are ordinarily curved and branched (due to random solidification), have the high strengths associated with whiskers. If an ingot of the eutectic alloy is unidirectionally solidified and appropriate control exercised over the thermal gradient, growth rate, and impurity level, the chromium fibers can be forced to solidify as fibers which are substantially parallel to the growth direction, Fig. 1. Uniaxial tensile tests on these straight chromium fibers extracted from controlled ingots3 have confirmed the earlier bend test results on curved fibers. Combining the facts that the strength and modulus of the chromium filaments are higher than the more ductile copper matrix and assuming that a "good bond" exists between the two phases, the Cu-Cr controlled eutectic system fulfills the requirements for effective fiber reinforcement of ductile matrices as established by studies on fiber glass reinforced plastics and other two-phase systems.4 Therefore, it was decided to study the fracture characteristics of morphologically simple specimens of chromium fiber reinforced copper (i.e., specimens of the controlled eutectic with substantially parallel reinforcing fibers) with the objective of establishing the dominant aspects of fracture. PREVIOUS WORK Comparatively little work has been done to understand the manner in which ductile alloys fail be- cause of the limited demand for this kind of information. Ordinarily ductility is specified for safety or similar reasons and when a part deforms plastically its useful life is terminated. In recent years, however, a number of investigators have begun to

Jan 1, 1963

By M. L. Fuller

IN connection with an investigation in this laboratory on the high-zinc side of the copper-zinc system, it was observed that well developed segre-gate structures of the Widmanstätten type were formed when a secondary phase precipitated from the solid solution of copper in zinc. This paper presents an analysis of the crystallographic relationship between the segregate and the solid solution matrix. The data to be presented are an interesting addition to the literature on segregate structures in that the plane of segregation is one of the less densely populated planes. In agreement with the generalization of C. H. Mathewson and D. W. Smith1 the plane of segregation in the matrix con-tains the direction of closest atomic packing of the lattice. Furthermore, the matrix and the segregate are both hexagonal close-packed, which has not been reported hitherto in the literature.2 The increasing com-mercial importance of zinc alloys containing copper makes this funda-mental study of value to the metallography of zinc alloys.

Jan 1, 1933

By Frank S. Shuri

INTRODUCTION The Calumet Pumping Station, located on the south side of the Greater Chicago area, is part of the Tunnel and Reservoir Plan to accomodate the city&apos;s wastewater. The Station consists of two parallel rock caverns, each 18 m high, 20 m wide, and 62 m long, located in Silurian dolomite approximately 91 m below the ground surface. The caverns are oriented N-S with a 24-m-wide pillar between them. Prior to construction, rock mechanics studies were conducted in an L-shaped test adit at the location of the west cavern. The purpo3e of the rock mechanic studies was to characterize the site, particularly the in situ stress field and deformation characteristics of the rock. This information, together with other physical properties of the rock and geologic data, was used to evaluate the stability of the preliminary cavern design, with particular emphasis on cavern orientation, rock reinforcement, and pillar stability. GEOLOGY OF THE SITE Stratigraphy The Chicago area is located on the Kankakee Arch, a broad, gently sloping arch of Paleozoic sediments. Rocks in the project area consist of Silurian dolomites unconformably overlain by Pleistocene glacial deposits. The formations of interest to this study are: - Racine Formation, inter-reef facies. This dolomite is gray- brown, silty, and compact. It contains occasional prominent bedding surfaces. The Racine Formation in the project area varies from 73 to 74 m in thickness.

Jan 1, 1984

By K. Aoki, N. Kameda, T. Esaki

The shortage of adequate construction sites and their difficult location has compelled many engineering structures to be planned in old mining areas in Japan. This paper shows, first, the characteristics of the excavated underground environment and next, the necessary preventive measures during construction of surface structures. Where the depth of a mined out area is relatively shallow, there is a tendency of cave-in consequent to surface loadings. The effect of surface loadings is inversely proportional to the depth of goals. Finally, a power plant project is studied as an example.

Jan 1, 1984