Search Documents

Jan 4, 1951

By Rodolfo V. de la Cruz

The in situ deformability of rock masses is determined by relating the applied load to the radial displacements of points on the borehole wall that are outside of the loaded surfaces. The external displacement method includes the steps in which: a) radial displacement sensors are installed to measure the change in length of a diameter of a borehole; b) unidirectional self- equilibrating pair of forces perpendicular to the direction of radial displacement measurements are applied on opposite sectors of the borehole wall, and; c) using elastic theory, the in-situ deformability of the rock mass can be related with the applied loads and measured radial displacements. The displacements outside the loaded surfaces are comparatively smaller in magnitude than displacements inside the loaded surfaces. These displacements, however, are sufficiently large and can be measured precisely by commercially available linear displacement sensors. Loads are applied by a conventional borehole jack. Existing methods for measuring the in situ deformability of rock masses yields unreliable results due to complex boundary stresses, small and varying contact areas, and the existence of fractures. It was shown that in the external displacement method, the effect of boundary pressure distribution and contact area are negligible. Also, since the displacements measured in the external displacement method were due to materials that are deeper inside the rock mass, borehole fractures have less influence on the calculated deformation modulus.

Jan 1, 1982

By D. K. Bose, C. K. Gupta, K. U. Nair

A new approach to processing an indigenously available low made molysulfide concentrate by chlorination with elemental chlorine in presence of oxygen is reported. Recovery of nickel and copper values associated with the sulfide concentrate by suitably treating the residue obtained after chlorination is also reported.

Jan 3, 1978

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually has been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,1 the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin" and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between [ ]

Jan 1, 1941

By C. Dinis da Gama

In order to reduce the complexity of mechanisms influencing rock. fragmentation by blasting a simulation approach is proposed, using the capabilities of microcomputer interactive graphics. Situations involving cratering end bench blasting are simulated, and both jointed and intact rocks can be subjected to explosive action, taking into consideration its breakage mechanisms. Size analysis curves relating rock distribution before and after the blasts are determined and compared with field data.

Jan 1, 1984

By W. T. Roberts, N. G. Turner

A study of the fatigue properties of several grades of commercially pure titanium has established that the strain-aging process is of minor importance in the development of a fatigue limit and a relatively high fatigue strength ratio. Metallographic observations and damping measurements at room temperature indicate that striations are able to spread from grain to grain only at stress levels above the fatigue limit. This suggests that the fatigue limit represents the stress above which large-scale dislocation unlocking takes place. Fatigue tests on annealed material at - 60" and - 196" c showed that under conditions when a thermally activated diffusion process would be suppressed the fatigue limit is not eliminated. Prestraining at room temperature did not have a detrimental effect on fatigue strength at room temperature but a decrease was recorded at — 60°C. This is further evidence that initial dislocation locking is a important strengthening mechanism. TITANIUM and titanium alloys have S-N curves with a definite fatigue limit, and a high ratio of fatigue limit to UTS can be attained. Other materials which show similar fatigue characteristics are mild steel and some Al-Mg alloys. The fatigue limit of these materials has been associated with their strain-aging capacity. It is well-known that commercial-purity titanium contains interstitial impurities which can give rise to a sharp yield point, and a small strain-aging effect following static strain has been demonstrated.7 This type of aging reaction is differentiated from the dynamic aging process when aging occurs during plastic deformation, and which is generally observed at elevated temperatures. In a titanium at room temperature, dislocation locking is associated with the interaction of interstitial oxygen, nitrogen, and carbon atoms with dislocations. Ehr-lich has shown that the distortion produced by introduction of these atoms into the hcp lattice has no shear stress component and hence there is no interaction between the stress field and the screw component of a dislocation. Thus the dislocations as a whole are only weakly locked. It is clear that strain-aging effects in hcp a titanium will be much less pronounced than those observed in bcc iron and steel. In recent years, the attribution of the fatigue limit solely to strain aging has been questioned. It has been pointed out that a definite fatigue limit is observed at temperatures as low as -196°C in some titanium alloys,' and strain aging is not expected to be effective at this temperature. The role of initial locking of dislocations in determining fatigue behavior has been examined in low-carbon steel by Oates and Wilson. They showed that under conditions in which the aging potential is low the factors which control the buildup of local stresses and hence affect dislocation unlocking, e.g., grain size, are important. There are indications that other metals can have a definite fatigue limit with no established strain-aging capacity, an example being magnesium12 which has the same crystal structure as a titanium. The spread of plasticity from grain to grain in hexagonal metals may be more difficult than in cubic metals because of the limited number of slip systems in the former, and this may account in part for their fatigue behavior. The present work was undertaken to elucidate the relative importance of crystal structure, strain aging, and initial dislocation locking in determining the properties of commercially pure titanium when subjected to cyclic stressing. 1) EXPERIMENTAL METHODS Three grades of commercial-purity titanium were used and a material of lower interstitial content was prepared by melting high-purity Japanese sponge titanium (referred to as H.P. Ti). The compositions and typical mechanical properties of the materials are shown in Table I. Fatigue tests were made in push-pull (zero mean stress) using an Amsler Vibraphore machine at a frequency of about 160 cps. Two types of fatigue specimen were used—one with a waisted gage length for determination of S-N curves and the other with a parallel gage length for metallographic studies and damping measurements. After careful machining and mechanical polishing, all specimens were electropolished prior to fatigue testing. The electrolyte consisted of 10 parts methyl alcohol, 6 parts 2-butoxyethanol, and 1 part perchloric acid (SG 1.54) and it was maintained at a temperature of -10" to -20°C during polishing. Tests at room temperature were normally carried out with the specimen immersed in a silicone oil bath which could be heated for elevated-temperature tests.

Jan 1, 1969

By B. F. Peters, J. Gordon Parr, E. R. Macgregor

A SERIES of seven hypoeutectoid alloys, up to 18.2 atomic pct Mn, was made by the levitation melting technique. The loss of weight on melting was considered to be entirely due to volatilization of manganese, and compositions were computed on this basis. Filed samples (—200 Tyler mesh) were helium quenched from 1000°C after soaking for 5 min by a technique already described.' Quenched Alloys -Assessments of the amounts of a phase produced and the hardness of the quenched alloys are summarized in Fig. 1. The experimental techniques and calculations involved have been described previously. The amount of a decreases as manganese content increases, until at 10.6 pct Mn only a trace of a' is observed. Previous

Jan 1, 1957

"The reduction works of the Boston & Montana Reduction department, near the north end of this dam is one of the reduction plants belonging to the Anaconda Copper Mining Company, the other being at Anaconda. These works employ about 1,100 men and have a capacity of about 3,800 tons of crude ore per day. This plant is now being remodeled to embody results of experiments and investigations which have been made with a view to more economic.al treatment of ores. A brief description of the plant as it will be after the remodelling is as follows:Concentrator Department: Consists of six units or sections, each section treating from 550 to 600 tons of crude ore per day. This department is not being. remodelled at the present time. A concentrating process, however, has been developed and partially installed in the old mill, and an experimental section embodying this concentration process has also been installed at the concentrator at Anaconda."

Jan 1, 1913

By Edwin R. Phelps, Charles W. Porterfield

BACKGROUND OF SURFACE MINING Surface mining refers to the process of removing the material (over- burden) overlying a coal seam and exposing the coal so that it can be loaded out and conveyed by trucks or other methods to the preparation plant or other facility. Surface mining has not always been important in the coal industry. In the early 1900s, almost all of the coal mined in the United States was mined by underground methods. In 1900, about 192 Mt (212 million st) of bituminous coal mere mined and less than 1% was mined by surface methods. The development and use of larger equipment has allowed surface mining to gain prominence throughout the years. Table 1 shows the total production of coal by mining method in the United States for ten-pear periods since 1920 and indicates the growth of surface-mined coal production. Surface mining will undoubtedly continue to account for a large percentage of the coal production in the US for many years because: 1) The capacity of surface mining excavators has continued to increase. Today, mining companies are using shovels (see Fig. 1) which are able to move up to 137.6 m3 (180 cu pd) in each bite and draglines (see Fig. 2) which move up to 168.2 m3 (220 cu pd) in each bucketful. 2) Increasing tonnage from the thick western coal seams is being produced by surface mining methods. 3) Surface mining has normally had lower costs and a better safety record than underground mining. 4) Surface mining normally recovers a much higher percentage of the coal reserve than can recovered by underground mining. 5) Some coal measures call best be extracted by surface mining

Jan 1, 1981

By Howard Reiss, C. S. Fuller

A theoretical and experimental study has been made of those interactions between holes and electrons which influence the solubilities of donors and acceptors in semiconductors. The major portion of the work concerns the solubility of lithium in silicon doped to varying degrees with boron. This solubility increases with increasing boron content in a manner predicted by theory and exhibits the expected temperature dependence. A qualitative experiment in germanium is described which demonstrates, in accordance with theory, that doping with a donor decreases the solubility of another donor. SEVERAL authors have discussed the possibility that holes and electrons behave like chemical entities and influence the solubilities of ionized impurities, Wagner was the first to invoke this concept in connection with his studies on nonstoichio-metric oxides. He used it again in explaining the solubility of hydrogen in molten binary alloys. In a theoretical paper,' Reiss drew attention to the fact that solutions of impurities in semiconductors

Jan 1, 1957

By R. S. Busk, R. F. Marande

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By R. F. Marande, R. S. Busk

The magnesium-aluminum-zinc 'system contains most of the magnesium-base alloys used commercially, although in practice the ternary alloys are usually modified by the addition of a small amount of manganese. Table I contains the magnesium-base commercial sand-casting alloys most widely used throughout the world, together with their typical tensile properties. These alloys may be regarded as a single family of varying aluminum and zinc content, disregarding manganese. A concise means of presenting data for them is by means of iso-property lines plotted on triangular coordinate paper. Constitutional, casting, and mechanical properties are presented in this manner. The data are given with the obiect of providing reference material, and to aid in the choice of a commercial alloy to serve a particular purpose. Detailed, critical analysis of the commercial alloys has been covered in a previous paper.' All alloys reported were made in rj-lb. melts, superheated to r700°F. for 15 min., cooled to r400°F. and poured in sand molds. The test bars produced had a 1/2-in. reduced section and were about 6 in. long. Except for the data represented in Figs. I and 3 the alloys used were of commercial purity and contained 0.1 to 0.2 per cent Mn in addition to the aluminum and zinc. Constitutional Data Under the heading of Constitutional Data are included all known data on con-

Jan 1, 1946

By E. S. Wheeler, M. W. Murphy

A LARGE part of the molybdenum produced in Colorado is converted and consumed in the Eastern States. As the raw materials and the power needed for the conversion of the Colorado concentrate are also accessible in the Eastern States, the conversion plant has been installed some 1500 miles east of where the ore is mined and milled. When concentrate was first produced at Climax in 1918, a custom smelter converted the product into ferromolybdenum. By 1924, the Company had decided to produce calcium molybdate and rented a building and installed equipment for that purpose at Langeloth, near Burgettstown, Pa., about thirty miles west of Pittsburgh. For the first few years the plant was a simple one of small capacity. A small hand-rabbled roaster was used, the product of which was made iota calcium molybdate by a conventional method; then an eight hearth mechanically rabbled roaster was installed to increase and speed up production. The output was considerably less than a million pounds of contained molybdenum annually until 1928, when a small part of the produc-

Jan 1, 1946

By J. O. Lewis

Oil wells usually reach their maximum daily output shortly after they are completed. From that time they decline in-production, the rapidity of decline depending on the output of the wells and on other' factors governing their productivity. The production curve of a well shows the mount of oil produced per unit of time for several consecutive periods; if the conditions affecting the rate of production are not changed by outside influences, the curve will be fairly regular, and, if projected, mill furnish useful knowledge as to the future production of the well. By the aid of this knowledge the value of a property may he judged, and proper depletion and depreciation charges may be made on the books of the

Jan 2, 1918

By W. L. Freyberger, H. Alter, K. L. Woodruff, E. L. Michaels

Laboratory and pilot scale tests have been made to determine the utility of heavymedia separation, particularly a cone-type separator, as a means of recovering aluminum and other values from shredded municipal solid waste. The effect of the method of shredding on the behavior of aluminum in a heavy-media system was determined. Two-stage pilot-scale heavy-media separations were made with size fractions of shredded refuse. Recoveries of aluminum, as well as other components of the refuse, were measured and medium losses determined. The experimental results indicate that with certain reservations a heavy-media cone system can be utilized for aluminum separation and recovery from shredded and air-classified municipal solid waste. Observations made using two-stage heavy-media separation in a drum unit are included. Qualitatively, the results from the two types of separators are similar.

Jan 1, 1976

By L. C. Glenn

IN the preparation of this paper the writer has drawn freely upon the writings of Orton, Munn, Shaw, Mather, Miller, Hoeing, St. Clair, Jillson, and others, as well as upon his own personal knowledge of the fields of both states. It is to be regretted that certain data gathered by him and his assistants last fall are not available for publication. OIL IN TENNESSEE A few wells drilled for brine for salt making in Tennessee between 1820 and 1840 obtained oil, but no definite search was made for oil until just after the close of the Civil War. Active drilling was then begun in Overton and counties southwest of it on the eastern half of the Highland Rim. A number of strikes were made at shallow depths in the basal part of the Mississippian but the wells were soon exhausted and abandoned. Drilling was revived, about. 1892, when the Spurrier district in Pickett County was developed and was followed by the Riverton district in the same county in 1896. A pipe line was laid from the Wayne County, Ky., fields and about 60,000 bbl. of oil were run before a very heavy slump in the production, a failure to find an extension of the field, and excessive local taxation caused the removal of the pipe line in 1906. There was then no production in Tennessee until the discovery, in 1915, of oil near Oneida, Scott Co., at about 950 ft. (289 m.) in fissures in the Newman or St. Louis limestone. This field, however, soon failed and was abandoned. In 1916, oil was found at Glen Mary, Scott Co., in the Newman limestone at a depth of 1232 ft. (375 m.) A number of wells have since been drilled there, some of which were dry while others, close by, were producers. The largest one yielded, at first, about 340 bbl. per day and produced for several months, when it suddenly went dry. Several of the first wells began at 6 or 8 bbl. per day and are still maintaining that

Jan 1, 1920

By A. F. Meger

REPRESENTED here are the ideas and varied experiences of many people in the Hanna Coal Co. who have helped develop, over a number of years, an efficient and flexible method for spraying con- trolled amounts of oil on coal. Since the George- town preparation plant began operations early in 1951, oil treatment of coal has received special attention. It is believed that oil treating will satisfy present customers and also attract new markets. The first step in developing the new method of oil spraying was the construction of a dust cabinet for testing 50-lb samples of treated coal with the available oil sprays on the market. Tests results were tabulated for both indoor and outdoor storage.

Jan 7, 1954

By A. Matsubara

Jan 1, 1922

By A. Matsubara

Jan 1, 1922

By M. A. Childers

Recent work with controlled laboratory tests.' field experience and a new analytical approach indicate that casing centralization, pipe movement and relative rheological properties between the mud and cement (yield point and density) are the three controlling factors in successfu1 primary cementing of dual casing. Turbulent flow has been demonstrated to be unnecessary under the severe displace ment conditions of parallel dual strings of casing. Simultaneous reciprocation of dual casing in directionally drilled boreholes is highly dependent on centralization and on the rapid initiation of pipe movement once the casing has been run to total depth. Successful cementing of 30 out of 32 dual, 3%-in casing wells substantiated these conclusions. A review of 15 dual, 3 1/2-in. casing wells completed prior to the adoption of these principles disclosed only one success. Mathematical and graphical techniques permit the engineer to analyze and anticipate the success or failure of a cementing operation. Standoff, mud displacement and reciprocation can be analyzed mathematically and planned in deep, directional or straight boreholes by review of annular geometry, relative rheological properties between the mud and cement, and forces caused by caring weight, functional drag and differential sticking. Introduction The objective in primary cementing is to displace the drilling fluid with cement that will bond to the formation and casing to prevent communication through the annulus. The predominant cause of failure appears to be channels of gelled mud that remain in the annulus after cementing.1 '* Past investigations have noted many procedures that could improve the displacement process.2-' These procedures include centralization, chemical preflushes, mechanical mud cake removers, controlled flow rates in certain regimes, pipe movement an1 control of mud and cement properties. Not until recently have the effects of many of these procedures been isolated so that their individual importance could be determined. In a recent paper,' a comprehensive and analytical laboratory study of various factors controlling the displacement process concluded that there are three major factors in obtaining complete mud displacement by the cement slurry. 1. Good relative rheological properties between the mud and cement. The cement should be heavier and have a yield point and plastic viscosity higher than the mud being displaced. Buoyancy forces often can dominate the displacement process. 2. High degree of standoff or centralization. The more centered the casing, the greater the likelihood of complete mud displacement and removal. 3. Pipe movement obtained by rotation or reciprocation. Often unfavorable rheological properties between the mud and cement, and poor standoff can be compensated by pipe movement. This work demonstrates the compatibility of the latter concepts with field results extended to the more severe dual casing displacement process. Early Experience With Dual 3'/t-In. Primary Cementing Early slim casing completions in the West Delta Block 73 field, offshore Louisiana, included 17 dual 3%-in., 3 single 3% -in. and 1 dual 2% -in. casing installations. Table I provides data on these earlier wells. Usually, common Class A cement was placed across the pay zone and 12 percent gel cement was placed to a height of 500 ft above the highest productive sand. Centralizers (6%-in. OD maximum expansion) were placed two or three per joint on both casing strings from total depth through the completion intervals and at least one per joint for the remainder of the cement sheath. A number of techniques and procedures were attempted to improve cementing success. Casing was run simultaneously or separately with a number of mud conditioning and circulating techniques. Mechanical aids such as cement bonders, slmiding sleeves, turbulizers and various sizes and strengths of centralizers were used. Common and gel cements were mixed with fresh or sea water with a number of different additives to control retardation and dispersion. Cements were thinned and mixed at high rates to try to induce turbulent flow in the annulus. On one well the "slow flow" method was used." Perforating was accomplished with a jet orienting gun. Unsuccessful cement jobs were indicated by production of extraneous fluids or by pressure communication between zones. On test, five wells flowed water, four flowed sand and six had pressure communication with the other string or the 10%-in. casing. A total of 25 remedial squeeze ce-

Jan 1, 1969