Search Documents

By M. E. Tyrrell, Alan H. Goode

The application of a simple, two-dimensional computer technique for evaluating rock burst potential in cut-and-fill stopes was investigated. The principal purpose of the study was to compare the effectiveness of high-modulus fill and destressing as aids in the control of rock bursts. Two conclusions that are probably of general applicability are drawn. First, high-modulus fill is ineffective as a means of increasing the mine stiffness and acts to control rock bursts only if it supports enough load to reduce substantially the stresses on the unmined vein material. Second, destressing is most effective if it is performed when the vein material is near the point of failure.

Jan 1, 1975

By Eric A. Nordhausen

A good deal of dialogue has been published and voiced concerning one mining regulation or another, that, according to those raising the issues, in effect shuts down or drastically reduces mine and/or mill reduction. The objective of this discussion is to there fore synthesize the various regulations affecting the uranium mining industry and attempt to realistically assess the extent of impact to yellowcake production - on both an individual and collective basis. Emphasis is placed on the later or newer permitting requirements under the Mill Tailings Act, Underground Injection Control Program, the Consolidated Permit Program, and the Resource Conservation and Recovery Act (RcRA).

Jan 1, 1980

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland's population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

By Richard D. Hagni

Abstract-Although the ore microscopist routinely examines polished sections to determine the mineralogy and texture of ores, his importance to the solution of problems peripheral to geology is not always fully realized. The techniques which he uses can be applied with little modification to the solution of a wide variety of beneficiation problem. By extending his studies beyond those normally considered to be of interest to the geologist, he can include examinations of polished sections of selected mill products. This is a logical extension, because the minerals and textures in the polished sections of ores are the same as those in mill Products. The mill dressing engineer should be more aware of the types of beneficiation problems that can be solved by the ore microscopist and what the ore microscopist can do for him. A greater degree of cooperation between the ore microscopist and the mill dressing engineer can be of significant mutual benefit. Ore microscopy holds an advantage over chemical analysis, because the interrelations and combinations of the mineral constituents of an ore or mil1 product can be visually determined. This advantage provides solutions to many beneficiation problems. Locking is a type of beneficiation problem that is particularly amenable to ore microscopy. The percentage, type, and distribution of locked particles can be readily determined with the aid of an ore microscope and an estimate made of the extent of additional grinding required for liberation. The extent of intimately locked types, which no reasonable amount of grinding will liberate, can also be evaluated. Mineral coating conditions, free particles of a deleterious mineral, and free particles of a valuable mineral held in floculated clusters of gangue are other features that can readily be observed. In some instances, visual examination may show that the problem is not one of locking. Photomicrographs illustrate the variety of beneficiation problems for which the ore microscope is applicable. These problems and their resolution demonstrate the importance of the instrument and show the value of close coordination between the mill dressing engineer and the ore microscopist.

Jan 10, 1978

By L. L. Melton, W. T. Malone

Fluid mechanics research conducted with non-Newtonian fluid systems now permits prediction of the behavior of these fluid systems in both laminar and turbulent modes of flow through circular pipes. Present work concerns non-Newtonian fluid systems currently used in the hydraulic fracturing process. During fracturing treatments, an unsteady-state condition may frequently be encountered arising from. the reaction rate of a chemical additive. This condition must be evaluated in order to predict the actual behavior of a particular fluid during field application. Design and operation of the apparatus used to determine fluid-flow behavior permit obtaining data under such non-equilibrium conditions. This paper shows methods used to obtain rheology measurements, develop hydraulic relationships and evaluate chemical reactions producing unsteady-state conditions. Engineering application of this research is illustrated by employing measured rheological values and developed hydraulic retationships to produce frictional pressure loss (psi/100 ft) us flow rate (bbl/min) charts of common tubing and casing sizes for an example fracturing fluid. How these charts and chemical reaction rate information are then combined to predict actual turbulent hydraulic behavior during unsteady-state field conditions is also discussed INTRODUCTION Many fluids used in hydraulic fracturing contain chemical additives which impart non-Newtonian fluid properties that may drastically alter their hydraulic behavior. Equally drastic alteration in wellhead pressure, injection rate and hydraulic horsepower requirement may result from these fluid properties. Prior research conducted to relate non-Newtonian fluid properties with hydraulic behavior has not as yet produced a universal relationship, particularly for the turbulent flow region. which of the many Possible non-Newtonian fluid properties is responsible has not been conclusively established. A systematic description, suggested by Metzner, of the many possible non-Newtonian fluid properties exhibited by real-fluid behavior, and a current discussion of theoretical and applied aspects of non-Newtonian fluid technoloy can be found in Handbook of Fluid Dynamics. f Little or no research has previously been attempted with fluids exhibiting time - dependent properties. Addition of chemicals during a fracturing treatment is often accomplished by continuously mixing and displacing the fluid. This produces a time-dependent effect or unsteady-state condition while the fluid is progressing through surface and wellbore conductors. This condition is due to solution or chemical reaction of the additive. Considerable departure from conventional methods of obtaining and interpreting data was found necessary to consider these conditions. Therefore methods were developed to obtain hydraulic behavior information under these complex, unsteady-state conditions. Relationships presented in this paper to predict hydraulic behavior of non-Newtonian fluids in circular pipes were obtained by constructing and operating a small pipeline apparatus in the manner of a pilot-plant study. These relationships are suggested as scaleup equations and are not proposed as fundamental rheological parameters. While perhaps deficient from a fundamental research viewpoint, a pilot-plant study does permit the determination and convenient evaluation of variables pertinent to a process. A pilot-plant study can result in a valid engineering application procedure even when fundamental relationships are still undefined. An excellent series of articles by Bowen has appeared in the chemical engineering literature.2-8 These give a thorough review of proposed hydraulic relationships and their limitations for non-Newtonian fluid behavior in circular pipes. A graphical method is presented to scale up data for a fluid exhibiting an anomalous hydrau1ic behavior in the turbulent flow region. Considerable assistance has been obtained from these articles to interpret the anomalous behavior noted during this investigation. These articles also provided assurance that a pilot plant is a practical approach to evaluate the hydraulic behavior of non-Newtonian fracturing fluids. _____________

Jan 1, 1965

By Edmund M. Warner

Any city dweller who has walked alone along a remote mine passageway has to be impressed by the eerie silence-the total absence of noise except for one's own breathing and scuffing of boots on the bottom. An underground mine can have tremendous contrasts, from complete silence to the ear piercing clatter of percussion drills working in the mine roof. Noise in underground mining machines is both useful and detrimental. Without characteristic noises that are recognizable to miners, operators would have a more difficult job operating their machines. Noise serves as a warning of approaching machinery, and changes in noise give indication that breakdowns may occur.

Jan 1, 1979

By L. A. Roe

The flotation of fine particles less than five microns in diameter and the flotation of liquids from liquids generally requires bubble generation methods different than methods used in dispersed air type machines used in mineral flotation. Conditions in the separatory zone in mineral cells are generally more dynamic as compared to the quiescent conditions often absolutely necessary for the flotation of fine particles and liquids. An example of quiescent flotation with very fine bubbles is the lithium flotation plant which operated at Trona, California for 34 years, until it ceased operations in 1978. A review of the process development and the commercial flotation operations at Trona is given in this paper. The clarification of oil field brines by flotation of the oil from the brine has been used for over twenty-five years. Recent installations related to the Prudhoe Bay oil field and the Alaska pipeline are described.

Jan 1, 1980

Dr. F. W. C. Schniewind, New York, N. Y.:—Mr. Vogel speaks of briquetting the flue-dust by means of lime. I learned recently in Europe of a process employed with considerable success at one of the blast-furnaces, where blast-furnace cinder is used with lime. The lime and cinder are mixed with the flue-dust, and exposed to superheated steam, which converts the blast-furnace cinder into cement. Briquettes are then formed in the usual way. Mr. Vogel :—The process referred to is the " Scoria process," which has not been in use for some time past. For that reason, I did not mention it. Prof. Arthur L. Walker, New York, N. Y.:—I would ask the commercial name for magnesium chloride, and where it can be obtained ? Mr. VoGel :—I mentioned magnesium chloride, because it has been used abroad to a large extent. In Germany it is obtained as a by-product in the manufacture of potash-salts; in the United States we have been using chloride of lime, which is cheaper. Otto Sussman, New York, N. Y.:—What is the cost of this process ? Mr. Vogel :—The cost is exceedingly low. I can give you the figures from abroad, but not for the United States, because the system has not -yet been used here commercially to

Jan 1, 1913

Jan 1, 1934

By Benjamin L. Miller, Charles H. Breerwood

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Charles H. Breerwood, Benjamin L. Miller

From earliest recorded times, limestone has been employed in the industrial life of peoples of all sections of the world where it exists. It is widely distributed and therefore has been available in almost every country and has been employed for a variety of purposes. Its earliest use was for buildings, since it is more easily quarried and dressed than most other kinds of rocks and so could be utilized by early inhabitants, poorly equipped with tools. The next use was in the manufacture of lime, which was employed by the ancients in mortar. These two uses of limestone are still all important, but they have been overshadowed in scores of regions by literally hundreds of new applications for raw limestone or products made from it. Anyone familiar with modern manufacturing processes can quickly call to mind many industries in which limestones are essential, and new uses are continually coming to notice. Any enumeration would probably be incomplete and soon out of date. Origin of Limestone Disregarding details and unusual types concerning which often there is insufficient evidence and considerable difference of opinion, limestones have been formed by the precipitation of calcium carbonate from solution through the action of organisms, both plants and animals, or in a limited number of instances by chemical reactions without the intervention of living forms. Some of the organisms extracted the calcareous material in order to build up hard structures, either as bony skeletons or as coverings (clams, snails, etc.), whereas others in their life functions emitted substances that resulted in the precipitation of the soluble constituents outside the organisms themselves. In some instances the organisms utilized only calcium carbonate but in some cases other compounds as well were precipitated. Various materials have been found in the hard parts of animals, and for that reason it is almost impossible to find a pure natural limestone; that is, one composed entirely of CaCO3.

Jan 1, 1938

By Irwin Roman

NUMEROUS results and formulas have been published for analyzing seismic records, but most of them apply only to large-scale phenomena such as are encountered in studying earthquakes. In a few cases,1 formulas have been published for some of the simpler structures. In the present paper, an attempt will be made to analyze several types of struc-tures without using methods more advanced than those of a first course in calculus. In, tracing a disturbance through a medium, it is almost always possible to base the analysis on Fermat's Principle of Extreme Time, which states that waves of displacement travel between points in such a manner as to make the time of travel an extremum with respect to all neighboring paths. In the simpler cases, comprising most of those used in optics or geophysical prospecting, this time is a minimum and the principle is often referred to as the Principle of Least Time. Within a homogeneous medium, having a uniform speed of transmission of the disturbance in all directions and throughout the medium, the paths are straight and are refracted at the interfaces in accordance with the Snell law of refraction, which states that the ratio of the sine of the angle, made by the ray with the normal to the interface, to the speed of trans-mission is the same on both sides of the interface. Thus, in any medium composed of homogeneous sections, this same ratio has a constant value at all points. In particular, if all interfaces are horizontal, it is apparent that the angles of incidence are the angles made by the ray with the vertical direction. Furthermore, the incident ray, the refracted ray and the normal to the interface are all in the same plane at each refraction;

Jan 1, 1933

By H. J. Ramey

Conventional calculation of total system isothermal compressibility for a system containing a free gas phase involves, among other things, evaluation of the change of oil and gas formation volume factors and the gas in solution with pressure. Preferably, this information should be obtained from laboratory measurements made with particular oils and gases. Often, experimental measurements are not available. In this case, it is necessary to obtain pressure-volume-temperature relationships from general correlations such as those of Standing' for California oils. In order to speed estimates of compressibility, generalized plots have been prepared of the change of both oil formation volume factors and gas in solution, with pressure from Standing's correlations. A generalized plot for estimating the change in the two-phase (oil and gas) formation volume factor with pressure is also presented. Usually, the effect of gas dissolved in reservoir water upon the total system compressibility is neglected for gas saturated systems, due to the low solubility of gas in water. Results of this study indicate that the increase in total system compressibility caused by solution of gas in water is often as large as the compressibility of wafer, and can be magnitudes larger for low pressure systems. Generalized results for estimating the change of gas in solution in water with pressure are presented in tabular and graphical form. INTRODUCTION During the past decade, pressure build-up and drawdown techniques have gained an important place in reservoir engineering. Build-up and drawdown analyses are only two special applications of the broad field of transient fluid-flow theory. All solutions of transient fluid-flow problems contain a parameter called the total system isothermal compressibility. This property of fluids and porous rock is a measure of the change in volume of the fluid content of porous rock with a change in pressure, and it may vary considerably with pressure. Evaluation of total system isothermal compressibility is not difficult, but it is tedious and time-consuming. Often compressibilities are estimated roughly, or transient flow methods are neglected completely. The benefits of using accurate system compressibility in properly-executed build-up or drawdown analyses are: 1. Better planning of pressure build-ups may be achieved to avoid unnecessary loss of revenue due to excessively long shut-in periods, or to shut-in periods too short to yield useable data. 2. Better and more reliable estimates of static formation pressures for reserves estimates and rate performance estimates. 3. Reliable information for evaluation of well completion effectiveness, and planning and interpretation of well stimulation efforts. The purpose of this paper is to clarify the nature of the total system isothermal compressibility, and to present useful methods for estimation of compressibility, particularly for systems containing a gas phase. DEVELOPMENT Numerous publications have presented solutions to transient single-phase flow of slightly compressible fluids, stressing pressure build-up applications. In transient flow, a compressibility* term arises to permit volume content of fluids in porous rock to change as pressure changes. The basic nature of the compressibility term is usually taken for granted. Problems arise in practical applications of transient fluid theory because most published works consider only one flowing fluid—in an ideal porous system containing only one fluid. In 1956, Perrine2 presented an intuitive extension of single-phase flow pressure build-up methods to multiphase flow conditions. Later, Martin- established conditions under which Perrine's multiphase build-up method had a theoretical foundation. Perrine has shown that improper use of single-phase build-up analysis in certain multiphase flow situations can lead to gross errors in estimated static formation pressure, permeability and well condition. It is likely that, much pressure build-up data for oil wells should be analyzed on the basis of multiphase flow. For both single-phase and multiphase build-up analysis, the isothermal compressibility term in dimensionless time groups often should be interpreted as the total system compressibility. All real reservoirs contain one or more compressible fluid phases. In addition, rock compressibility can contribute in an important way to the total system compressibility. The proper total system compressibility expression may contain terms for compressibility of oil, gas, water, reservoir rock and terms for the change of solubility of gas in liquid phases.

Jan 1, 1965

By J. A. Brierley, Roshan B. Bhappu, D. H. Reynolds, P. H. Johnson

Although the economic importance of recovering copper by leaching of mine work dumps from open-pit operations has been realized for some time, serious attempts to understand and to improve such operations through scientifi research has been made only in recent years. This progress report covers the results of chemical, physical, and biological studies pertaining to the dump-leaching process and discusses salient features and parameters that may be helpful in improving such operations. The dump leaching of low-grade copper ores, as an integral part of the open-pit mining operations in the Southwest, has been practiced for the last 50 years and is increasing in importance as one of the major sources of copper. The recent acceleration in dump leaching can be attributed to: (1) the greater tonnages of low-grade ores mined and dumped at newer mines as well as resulting from increased stripping ratios at the older mines, (2) the relatively small investment required for dump leaching facilities per pound of copper recovered contrasted with expansion of milling facilities to recover equal amounts of the metal by raising tonnage throughout, (3) low labor requirements needed for leaching, and (4) the simple and continuous nature of the process needing little close supervision of trained operators. In the past, the mining companies have not worried about efficiency in dump leaching but have been satisfied with whatever metal recoveries could be made without much effort. However, because of the huge amounts of metal accumulating in the low-grade waste dumps, compared to the relatively small amount recovered annually, an operator today cannot leave dump leaching to chance. What appears to be a simple, empirical process is actually a very complex one involving a large number of critical factors that encompass Several Scientific disciplines, such as physics, chemistry, geology, biology, and hydrology. It is imperative that

Jan 1, 1970

By Y. L. Yao

The solubility limit of oxygeu in a titanionn at 850°C has been determined by magnetic measurements as 12.5 + 0.5 pct (29.0—30,9 at. pct). Also in the susceptibility-co~centmtion curve, there is n distinct but not sharp maximum at 19.0 * 0.5 z~t pet (40.5--42.1 at. pct), which indicates the presence of the 6 phase. The magnetic susceptibilities of the alloys of the titanium-oxygen system were determined byEhrlich in 1939.' is alloys were prepared by sintiring mixtures of titanium and its oxide at high temperatures. On the titanium-rich side, despite the fact that the alloy compositions he measured crossed two phase boundaries, the limited results obtained

Jan 1, 1960

By Thomas Watson

INTRODUCTION THE users of barite in the United States derive their supply partly from the domestic production and partly from the imports from foreign countries. According to the Mineral Resource division of the U. S. Geological Survey, the domestic production of barite in 1913 was 45,298 short tons, valued at $156,275, or $3.45 a ton, and the imports of crude barite were 35,840 short tons, valued at $61,409, or $1.71 a ton. These figures clearly show a decided advantage in cost of the foreign over the domestic barite to users in the United States. The difference in cost is the only advantage to the consumer of foreign barite, for there are large reserves of the mineral in the United States of good grade. The production of many of the operating mines is capable of decided increase, and it is believed that the operating mines together with the large reserves of undeveloped deposits of barite are entirely adequate to meet the demands of the users in the United States. Deposits of barite are known in California, Idaho, Nevada, and Alaska, but most of them are undeveloped because there is, apparently, no market for the .material in that region. The domestic production is derived from Missouri and the Appalachian States, the greater part being obtained from Missouri. Following the outbreak of war in Europe many users of foreign barite in the United States have been forced to seek their supplies at home. It seems opportune at this time, therefore, that a general review be given of the barite industry in the Appalachian States, one of the two areas from which the domestic supply of the mineral is derived, and that attention be directed to the undeveloped deposits in the region. Briefly, then, this paper reviews the barite industry in the Appalachian States, and describes the occurrence, preparation, and uses of the mineral.

Jan 2, 1915

By A. A. Bauer, F. A. Rough, G. H. Beatty

AS a result of recent studies, the constitution of the zirconium-uranium system has been fairly well defined. A diagram for the system is shown in Fig. 1. However, both oxygen and nitrogen are known1-3 to have a pronounced effect on the limits of both ß- and e -phase regions. It has been shown that small amounts of oxygen severely constrict the compositional limits of these phase regions in the ternary zirconium-uranium-oxygen system. A previously published tentative diagram shown in Fig. 2 illustrates the ß-phase constriction resulting from oxygen additions. Generally, iodide zirconium has been used in constitutional studies of zirconium-uranium alloys. While this is the highest purity material available, cast iodide zirconium-uranium alloys will generally average from 200 to 300 ppm 0 and from 50 to 60 ppm N. Thus, while the constitution of the zirconium-uranium system is fairly well defined, it must be realized that this definition applies to alloys containing in the vicinity of 250 ppm 0 and 50 ppm N. The present investigation was undertaken to accurately determine the boundary between the ß-plus-P and ß phases at a single temperature in the binary zirconium-uranium system by quantitatively

Jan 1, 1959

By Robert N. McIndoo, M. G. Woodle

10.5-1. Introduction. In the not-too-distant past, maintenance and the facilities for maintenance were considered a necessary evil to be given only secondary consideration in the development and planning of a surface mine operation. With the increasing sophistication of mining equipment and machinery, this concept has been replaced; and today's mine managers recognize that planning for adequate maintenance facilities is as important to a successful operation as a sound mining plan. This chapter will present the basic maintenance facilities and the fundamental considerations necessary to meet the varied requirements of surface mining. 10.5-2. Determination of Shop Facilities. The size, shape, and extent of maintenance facilities are contingent on the general mining plan, the location relative to outside facilities, and to the available capital. The type of construction employed is dependent on climatic conditions and preference. HAULAGE SYSTEMS. The type of haulage equipment used will dictate the kind of shops needed. Truck haulage requires entirely different facilities than rail haulage. Some mines will employ both systems, and can include hoists, skips, or conveyor belts in combination with locomotives or trucks. The requirements of each type will be discussed. MAINTENANCE ORGANIZATION. The pre-planning decision as to centralized maintenance vs. area maintenance, or a combination of both, will greatly affect the maintenance facilities required. A single pit with relatively short travel from shops to pit will probably have a centralized maintenance system. Where more than one mine is involved, or where there are diversified sections or functions in a mine (mine equipment, mill, conveyor, or

Jan 1, 1968

By C. F. Wang

Page I. Introduction............:.............. 395 Manchuria in General ....................... 395 Pen-hsi-hu............................ 397 Pen-hsi-hu Coal & Iron Co., Ltd................... 399 I1. organization........................... 400 III. Coal Deposit........................... 402 Location..............................402 Geology............................. 403 Coal Mining...........'.................. 404 Mining Methods........................407 Mining Cost.........................408 IV. Coal Washing Plant.......................408 V. Coking Plant..........................410 VI. Iron Deposit...........................413 Magnetite Belt.......................... 413 Origin of Deposit......................... 414 Iron Mining........................... 415 VII. Concentration Plant........................ 417 VIII. Briquetting Plant.......................... 418 IX. Blast-furnace Smelting...................... 418 iNTKODtrCTION Manchuria in General Manchuria. called the "Three Eastern Provinces" in Chinese. forms the northeastern corner of China and is bordered by Siberia on the north and northeast. and by Korea on the east. It is a land famous in Chinese annals as the place of origin of the Ching dynasty. and in more recent times it has bcen an arena for diplomatic maneuvering and commercial competition between the Russians. advancing from the north. and the Japanese from the southeast. It derives its name of "three eastern provinces" from the fact that it is divided into three provinces; Hei-

Jan 1, 1918

By G. H. Clevenger

Continuing the discussion of the paper of James Johnston, presented at the New York meeting, February, 1914. See Trans., xlviii, 3 to 32 (1914). This paper cannot fail of being of great interest and value to all who are interested in the cyanide process, on account of the important developzn~ents which it records. Mr. Johnston is to be commended for the large amount of detail which he gives, and the company and its management for permitting the publication of data of this character, which while of great value to others could well be considered private property. It might be discussed from a number of standpoints: First, as an example of recent practice in mill and cyanide plant construction; second, the mill practice; third, the cyanide practice; and fourth, the new features in cyanide treatment involved. Perhaps a more vivid way of expressing it would be: First, the equipment or tools with which the various operations are carried on, are they the best and most efficient which could have been selected for their respective uses; and, second, is the best use in every case made of these tools? It may be well inquired is the highest possible recovery of silver made at the lowest cost per ounce recovered? For after all, the making of the greatest ultimate profit is inseparably associated with successful metallurgical practice; there must therefore be at all limes a careful balance maintained between recovery and cost of obtaining it. I wish to call attention in a very general way to the equipment used and to an anticipation of questions which are bound to arise in this connection. However, the bulk of my discussion will be confined to the presentation Of certain additional data, together with a more or less general discussion showing the line of development which leads up to the present practice and the applicability of certain features of it to similar problems elsewhere. There are a number of vital points of broad general interest involved in Nipissing low-grade practice upon which metallurgists will by no means be agreed to which I wish to call particular attention in the hope that it will lead to the presentation by others of data of practice in other districts which will assist in reconciling this divergence of opinion.

Jan 1, 1915