Search Documents

By P. V. Martin

Shortly after the middle of the nineteenth century, the invention of the regenerative open-hearth furnace and the development of the Bessemer process stimulated a rate of steel production whose magnitude created an unprecedented demand for pig iron. Revolutionary improvements in furnace design, auxiliary equipment, and operating technique enabled the blast furnace to keep abreast of the constantly increasing requirements of the steel mill. The development of improved blowing equipment, more adequate facilities for material handling, and particularly the general use of anthracitc and coke to replace the physically weaker charcoal, led to a rapid expansion in both the height and volume of furnaces. Beyond a doubt, however, the greatest single factor in blast-furnace improvement at this time was the use of the higher blast temperatures made available by the replacement of the recuperative iron pipe stoves by the regenerative Cowper brick stove. The increased blast temperature not only resulted in greater output but also reduced fuel consumption . far more than could be explained by the additional heat content of the blast. The progress of iron manufacturing was thus largely mechanical and thermal. Little attention was given the chemistry of the process until the publication of the investigations of Sir Lowthian Bell.1 Bell's painstaking experiments and investigations gave to the blast-furnace man his first real scientific conception of blast-furnace chemistry. Bell's recognition of the dual function of the carbon, the technical importance of reversible reactions and chemical equilibria, and his conception of the degree of oxidation of the carbon as shown by the analysis of the outgoing gases as a criterion of furnace efficiency, laid the foundation upon which has since been erected the structure of blast-furnace theory. Prominent among those availing themselves of Bell's data as .a basis of further study was M. L. Gruner,2 professor of the French School of Mines. His "Blast Furnace Phenomena," published in 1870, presented

Jan 1, 1940

By Comfort Adams

WHEN this country went into the war, but two concerns, The Bethlehem Steel Co. and The Midvale Steel and Ordnance Co., knew how to make steel fit for great cannons and at these concerns there were relatively few men who knew the whole art. Fortunately, certain of these men put their knowledge at the service of the Government, and proceeded to instruct the metallurgists at the arsenals and at various steel works. The then chairman of the Engineering Division of the National Research Council, Doctor Howe, suggested that this work might be facilitated, and the number of effective gun-steel makers thereby increased, if a detailed description of the best practice could be written, giving the reasons for the various steps, and issued with the endorsement of a committee composed of those who were evidently the most competent authorities. It was thought that something would be gained by clarification of the subject, and something by the eminent authority' of the members of the committee. To that end, the Engineering Division appointed-a committee, consisting of the gentlemen whose names follow, to mention only those who retained their connection with it. At, this time there were serious difficulties in the manufacture for the Government, of aircraft and high-speed engine crankshafts, of certain ordnance forgings, and of shells for both the Army and Navy. This Committee was asked to study and report upon these, with a view to betterment of practice. There were indications that the source of some of the difficulties went back to the melting of the steel and the production of the ingot. Hence, the committee first studied steel melting and ingot production, in order to guide the wartime manufacturers to an even larger percentage of useful production from the steel initially melted.

Jan 1, 1922

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By M. C. Udy, P. C. Rosenthal

The use of minute boron additions to steel has been given considerable attention in recent years. Comparisons made between boron-free and boron-containing heats of otherwise identical analysis have indicated, beyond a doubt, the potent effect of boron for increasing hardenability. The actual hardenability increase has been expressed as a multiplying factor, or in terms of the percentage of other alloying elements boron might replace. The present study presents the results of a systematic survey of the use of boron as an addition to two types of alloyed steels and as a replacement for various percentages of molybdenum in these steels. Both cast and wrought steels of the two basic compositions were prepared. Molybdenum, because of its scarcity at the time the investigation was started, was selected as the element to be replaced by boron. Attention was also given to the effects of boron on other properties of the steels, particularly their notched-bar toughness, to investigate other advantages or limitations of this element as an alloy addition. Experimental Work Steels Investigated The two basic compositions used in this survey of boron as a replacement for molybdenum are given in Table I. The cast steels were higher than the wrought steels in silicon content to improve the casting quality. Table i.—Nominal Composition of the Two Base Alloy Steels composition. Per Cent. steel Mn Si Ni Cr Xi-Cr-Mo Wrought 0.28-0.70-0.15-o.45—o.45-0.32 0.90 0.25 0.55 0.55 Cast 0.28-0.70-0.35-0.45-o.45- 0.32 0.90 0.45 0.55 0.55 hln-&lo Wrought 0.28-I .go-o.0.15-0.32 1.70 0.15 Cast o. 28- I.40- 0.35- 0.31 1.70 0.45 a Sulphur was 0.040 per cent maximum and phosphorus 0.030 per cent maximum. Each of these base steels, both cast and wrought, was made with molybdenum contents of o, 0.10, 0.20, 0.30, or 0.40 per cent, the total comprising 20 steels. In addition, each of these 20 compositions was prepared with boron additions in amounts of o.oo15, 0.003, and 0.006 per cent as ferroboron; and in amounts of 0.002 and 0.005 per cent as two commercial intensifier alloys, designated alloys A and B. The boron-treated steels totaled 100, and the entire series 120. Test Procedure Each steel was melted as an individual heat in a 50-lb., magnesia-lined induction furnace. Ingot iron scrap or mixtures of ingot iron and steel. scrap were used for melting stock. Deoxidation was carried out in the furnace with 0.10 per cent aluminum. The aluminum addition was

Jan 1, 1948

By A. S. McLatchie, R. A. Hemstock, J. W. Young

Much attention has been given in the past few years to methods of increasing the recovery of oil from proven reserves. Numerous laboratories have made investigations to evaluate the possibilities of increased oil recovery by high-pressure injection of dry gas, injection of a propane slug followed by dry gas, solvent flooding. and by the injection at relatively low pressures of gases enriched with ethane and propane. Several years ago, Whorton and Kie-schnick' published the results of laboratory studies on high-pressure gas injection which showed that, in the case of light oils, recoveries could be considerably increased by sweeping the reservoir with dry gas at pressures in excess of 3,000 psig. The increase was attributed by those authors to the vaporization of oil at the invading gas front and viscosity and solubility effects produced at the front by the invading gas. Later, Stone and Crump' presented the results of a series of displacement experiments in which a light under-saturated crude oil was displaced from sand-packed columns with unusually high recoveries when the displacing gas was a rich condensate or a dry gas enriched with ethane or propane. They also conducted similar experiments at higher pressure on heavy undersa tu rated crude oil, although in this case the increase in recovery was not as great as in the case of the light oils. In both cases, viscosity reduction and swelling of the by-passed oil behind the invading gas front were believed to be responsible for the more favorable recovery of the original oil in place. Within the past year, other investigators", ' have presented the results of laboratory studies of miscible slug and solvent flooding recovery processes. This paper describes the laboratory methods developed for evaluating benefits to be obtained by enriched gas drive in specific reservoirs, and presents the results of several displacements of crude oils which possess a wide range of physical properties. The displacements were conducted at reservoir conditions of temperature and pressure. The apparatus used in the following experiments consisted of a sand-packed tube which served as the model reservoir, a cylinder of injection fluid, and a mercury pump. The stainless steel tube, 8 ft long and 0.53 in. I- was packed with a graded quartz sand. The high-pressure pump discharged mercury into the bottom of the injection fluid cylinder at a constant rate as low as 1 cc/hr. The average porosity and permeability of the sand column were 34.6 per cent and 3.25 darcies, respectively. In each case the tube was charged by the displacement of salt water by the reservoir oil under consideration. Recently a project was initiated to evaluate oil recovery by enriched gas drive from three oil reservoirs. Samples from a fourth reservoir (in this case high-viscosity oil) were studied with a view to obtaining recovery information of general applicability to low-grade, high-viscosity crudes. The oils from these four reservoirs exhibited a wide range of physical properties, and the reservoir conditions of pressure and temperature simulated in the laboratory represented several typical field conditions under which enriched gas drive might be employed. One of the reservoirs selected for laboratory displacement experiments produced an intermediate-gravity crude (29.6" API) by solution gas drive and a weak water drive. A low recovery in the range of 10 to 20 per cent was anticipated. Four displacement experiments were made to determine the effect of injection gas composition and initial gas saturation upon recovery of oil from the laboratory model. Two types of reservoir oil were used in these experiments. In the first run, a desaturated crude with a bubble point of 395 psi was charged to the tube. In the three subsequent runs, a simulated original reservoir oil was charged at 2,000 psi and produced by solution gas drive to 300 psi before beginning gas injec-

By Edmund Davenport

Tier; production of thorium of high purity by the Ca-CaCl2 reduction has been described by Marden and Rentschler,1 who also reported some of the properties of the coherent, ductile metal obtained from this pure thorium powder. The present paper describes the properties of thorium produced by the Ca-CaCl2 process modified in some details to meet commercial conditions. The principal effect of these changes in process has been an unavoidable increase in the oxide content of the thorium.

Jan 1, 1929

By Charles H. Jacoby

Solution-mined salt cavities are being used for storage of liquid petroleum gas, natural gas, and other hydrocarbons; waste disposal or storage; storage of radioactive wastes; and as a surge vessel for air compressed by an electric utility during off-peak hours. Examples of each use are given. Other contemplated uses of salt cavities are noted.

Jan 1, 1973

By Paul Cherin

ThE angle of intersection, 0, between h2k2l2 planes and the (loo), (110), (101), and (111) planes was calculated on an IBM 7040 using the well-known relationship

Jan 1, 1968

Jan 1, 1938

Modern, mechanized coal mine ranks with largest in the West - plays major part in CF&I's broad expansion program

Jan 11, 1953

ARIZONA Tucson University of AriZona, Mining Engineering Society. B CALIFORNIA Berkeley University of California, Mining Asso. B University of California, Library. B & T Los Angeles Chamber of Mines and Oil. B Southern California Local Section. T Public Library. B & T Oakland Oakland Free Library. T San Francisco California State Mining Bureau. T Mechanic's Merchantile Library. B Mining and Scientific Press. B Stanford University Stanford University Geological and Mining Society. B San Diego Public Library. B COLORADO Boulder University of Colorado, Library. T Denver Bureau of Mines. B Colorado Scientific Society. B Mining American. B Denver Public Library. B & T Golden Colorado School of Mines Magazine. B Colorado School of Mines Library. T Colorado School of Mines Scientific Society. B

Jan 1, 1923

By F. M. Hamilton, R. G. Fleck

As the result of extensive small laboratory experiments, the metallurgical results of sintering iron ore from the Benson mines at Star Lake, N. Y. were clearly defined. But the practical operation had not been proved; so, the sintering strand, which went into operation at the mines in 1952, was designed to minimize the risk involved. It was built by the Dwight-Lloyd Div. of McDowell Co. Inc.

Sep 1, 1956

Jan 1, 1949

By E. D. Meier

SINCE Dr. St. Albans, in 1840, began to build successful watertube boilers—some of which are still in use—the gravity-return water-tube boiler has been built in many forms, more or less familiar to all who have studied the subject. A single firm in this country published recently a pamphlet, showing some fourteen modifications of their boiler during about as many years. There were hence available to the thoughtful inventor of this latest form many data showing what forms were to be avoided, as well as the effects sure to follow certain erroneous methods of construction in the older types. Improvements in materials, tools, and workmanship made possible, forms formerly prohibited by excessive cost. The first Heine boiler was built by A. Borsig & Co., for the

Jan 1, 1886

By J. R. Thoenen

THE Bureau of Mines has used various sizes of core barrels above 2 in. and below 10 in. in diameter to core manganese, potash, coal, brown iron ore and bauxite. The paper describes in some detail the methods and types of equipment used to obtain maximum sampling accuracy.

Jan 1, 1947

By H. A. Wheeler

It may surprise some of our members to learn, that, among the industries based on the mineral resources of the United . States, clay now ranks third, being exceeded in value of product only by pig-iron and coal. The present annual value of clay-products exceeds the value of the outputs of gold or silver, and also exceeds the combined values of copper, leacl, zinc, aluminum, mercury, antimony and nickel. These facts are shown in Table I. which gives the statistics for the year 1902 :

Jan 1, 1905

[ ]

Jan 1, 1938

By F. S. McNicholas

IN the first big blast at Climax, a "loop back" (three-wire system) was used (Fig. I), with the idea of securing a wiring system that would give to all series the same amount of current. Single-phase, 60-cycle, 13,800-volt [ ] power was furnished to the blasting transformers, each of which has a rated capacity of 600 amp. at 480 volts. Two blasting leads were taken from these transformers, giving a blasting current of single phase, 60 cycle, 480 volts, with an instantaneous capacity of more than 600 amp. The blasting switch was on the secondary leads from the transformers, to avoid lag in energizing them.

Jan 1, 1938

By H. F. Silver

Although the literature indicated that a hydrogen-ated coal bitumen might be used as a substitute for petroleum asphalt and road tar, no work could be found in which the material was actually used or evaluated as a road binder.' Therefore, a study was initiated to investigate the production and properties of a road binder made by hydrogenating coal in the presence of a solvent at elevated temperatures and pressures. HYDROGENATlON PROCEDURE Four different samples of sub-bituminous Wyoming coals and three samples of coals from other states, ranking from lignite to a low-volatile bituminous coal,

Jan 1, 1969

By R. R. Nash, W. F. Sheely, E. D. Levine

ThiS note reports on the variation with temperature of critical stress for basal slip of binary solid-solution single crystals of indium and of thorium in magnesium. PROCEDURE Alloy single crystal spheres were acid machined to 3/8-in. diam cylinders with the basal planes of the crystals normal to the cylinder axis and then annealed at 810°K. Stress was applied parallel to the slip system, (0001) [1120]. Experimental details will be presented in another paper.' Two nearly equivalent' techniques of stressing were used. Stress on the magnesium-indium alloy crystals was increased by 1 g per sq mm at 1-min intervals, and the critical flow stress was defined as the lowest stress to pro-

Jan 1, 1960