Search Documents

By Don H. Baker

THE need for new or improved refractory materials has caused metal phosphides to be given renewed scrutiny. Some metal phosphides show high-temperature inertness, are exceptionally hard, and exhibit a marked resistance to chemical attack. Various metal phosphides have been prepared for study by direct combination of the elements,'-' by reaction of metal or metal compounds with phosphine or phosphorus trichloride,'"' by thermal decomposition of a metallic phosphate or phosphite,"-'8 and by molten salt electrolysis.19 Electrolytic preparation of phosphides of titanium, manganese, and chromium from their oxides is reported in this paper. An externally heated 3-in.-ID by 6-in.-deep graphite cell, that served as the anode as well as a container for the electrolyte, was used in these investigations, and a suspended, centrally positioned graphite rod served as the cathode. A closely fitting silicon carbide furnace liner minimized atmospheric oxidation of the crucible. Electrolyses were performed for predetermined periods and current settings. Preliminary research had indicated the more efficient current and potential settings that could be used. Upon completion of the deposition period, the deposit was hot-stripped from the cathode. The mass of crystalline deposit, plus occluded and adhering salt, was crushed to minus 10 mesh and hot-leached in dilute hydrochloric acid. The leached crystalline material was water-washed, dried, and sampled for analysis. Products were identified by X-ray diffraction and standard analytical procedures. Electrochemical studies were initiated to establish the optimum conditions necessary to produce manganese phosphide (MnP), titanium phosphide (Tip), and chromium phosphide (CrP). Among the factors studied were the operating temperature, the imposed current, and the electrolyte system. If the temperature, or imposed current, was too high, deposition of phosphorus resulted, and if either were too low, partially reduced lower oxides were deposited. The operating conditions established for repetitive high-quality production of metal phosphides of the MP structure are presented in Table I. The metal phosphide crystals varied in size, but all had a definite metallic appearance. Typical are the crystals of CrP shown in Fig. 1. Evaluation data and analysis of the crystals are presented in Table 11. Efforts to measure resistivity of these three compounds over the temperature ranges of 250o to 400°K were hampered by the small physical size of the crys-

Jan 1, 1968

By V. R. Garfias, A. C. Fernandez

Despite artificial curtailment in all the fields of Mexico during 1937, owing to strikes and other disturbances, the production of crude petroleum aggregated approximately 46,738,000 bbl., showing a substantial increase of about 5,571,000 bbl. over the preceding year. Most of this increase occurred in the Poza Rica area, where, although only two wells were completed during the year, production increased from 14,162,000 bbl. in 1936 to 18,634,000 in 1937. While production in the South fields (Golden Lane) remained practically stationary, the output in the heavy-oil district of the Northern fields showed an increase of 1,930,000 bbl., because production had been considerably curtailed during 1936. Production in the Isthmus of Tehuantepec decreased about 596,000 bbl., owing to labor disturbances. Crude run to stills in local refineries increased from 34,000,000 bbl. in 1936 to 36,650,000 in 1937. Exports of crude and refined products were approximately 22,700,000 bbl., or 500,000 bbl. less than in 1936. Domestic consumption, excluding ships bunkers, reached a total of 20,000,000 bbl., which shows a small increase of 200,000 bbl. over the. previous year. Domestic demand for gasoline is estimated at 3,400,000 bbl. for the year, which represents an increase of 500,000 bbl. over 1936. In all, 60 wells were completed in Mexico during 1937, as compared to 70 in 1936 and 74 in 1935. In proven areas 52 completions resulted in 25 producers and 27 failures. In the Northeastern area near the United States border, five gas wells were drilled, all of which were producers; one of them, in Camargo, came in with a daily production of 20,000,000 cu. ft. of gas. One well, resulting in a failure, was drilled in Las Uvas, Coahuila, and three wells were completed in Quebrache, to the southeast of the heavy-oil district, resulting in two small producers and one failure. TWO more wells drilled in San SebastiBn, east of the Golden Lane, were failures. Fields Northern Fields (Heavy-oil District).—A total of 11 producers and 22 failures was completed in the proven areas of the Northern fields, as compared to 16 producers and 25 failures in 1936. In the Altamira

Jan 1, 1938

By Graham John Mitchell

In May, 1919, a crosscut on the 1400-ft. level of the Briggs mine, a Calumet, & Arizona property at Bisbee, Ariz., penetrated a deposit of pyrite and chaleopyrite that had replaced quartzite and limestone and was cut, especially in the quartzite, by numerous fractures. As the drift advanced through these fractured portions, they were found to be free from copper-sulfate minerals although '(sooty" chalcocite was present in the fractures and also as coatings and replacements of pyritc. Howcver, sulfate soon made its appearance in certain fractures, filled them, and began to form stalactites. Several centers of incipient growth were noted for subsequent study, observations in the drift at frequent intervals during the past 17 months affording the opportunity of determining the rate of formation of the stalactites. The one to attain the greatest growth during the period of observation measured 27 in. long and averaged 1 in. in diameter. A close study showed it to be composed of small interlocked crystals of chalcanthite radiating from a small central tube-like opening. The trielinic form of the crystals was evident with prism and pinacoid faces recognixable. Assuming that the supply of copper-sulfate solution was constant (luring the 17 months—-and such an assumption is supported by the fact that the number of drops of excess solution falling, per minute, from the tip of the stalactite at the times of observation checked closely—thc stalactite, it has been estimated, grew at the rate of 1.58+ in. per month. DISCUSSION James I?. Kemp," New Yolk City.—J. S. Curtiss, in the monogr:tpll on Eureka, Ncv., say:: that a stalactite formed in limestonc grew 5/8 in. in three weeks and continued to grow as long as it had a drop of water or solution at the lower end. Another grew at the rate of 3/8 in. in the same time. In the case cited by Mr. Mitchell, the growth was about 136 in. in three weeks. A year ago we had an instance of the formation of cubes of galena on a railroad spike. A mine in northeastern Oklahoma had been idle about two years but on account of pumping of neighboring properties, the circulation of water was active throughout the drift. A cube of galena,

Jan 1, 1922

By Alfred James

John Stewart MacARthUr, born in 1856, was the son of Robert MacArthur of Glasgow, and came of Scots stock distinguished for character and religious conviction. His election as elder of the Free Kirk gave him greater pride than the receipt of the gold medal of the Institution of Mining and Metallurgy. The former honor was for character— it marked him as a son worthy to follow in his father's footsteps; the latter was awarded for his life work of eminent service to the gold industry. Cheery optimism, resolution, tenacity of purpose, and industry ever characterized his actions. Apprenticed to the Tharsis Sulphur & Copper Co., his work on the chemical staff brought him to the notice of the Cassel Gold Extracting CO.,. at that time struggling with an unworkable electrolytic process..He was engaged by that company, in 1886, as technical manager and before long brought out the perchloride process, which was speedily followed (in 1887) by the epoch-making cyanide process. This process revolutionized gold mining and directly led the way to the elevation of the mining engineer to the most broadly trained product of the engineering profession. A noteworthy feature of the cyanide process was its completeness when introduced. Over thirty years have elapsed and the use of the process has been worldwide, but no suggested improvement has stood the test of time. The extension of the process to the beneficiation of silver ores—containing far more metal per ton and thus requiring the employment of stronger solutions—has brought us the Merrill and Crowe improvements in precipitation and the Nipissing desulfurization process for certain silver-hearing minerals. Roasting apparatus, fine crushing, filtration, and settling equipment have all aided the extension of the process in and from its original field. As Hennen Jennings put it,, the cyanide process today is essentially that of 1890. This self-containedness of the cyanide process arose from no mere chance; it was directly due to MacArthur. It was he who personally investigated every known method of precipitation and then every form of zinc from sheet, punchings, filings, millings, rods and shaving down to fume; it was he who investigated the effect of protective alkalies, of so-called accelerators, and of the addition of lead salts; he was determined to leave nothing to chance.

Jan 1, 1921

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By H. W. Imholz

Active interest in the North Central Texas area centered in the development of the Palo Pinto limestone-producing zone, near the town of Avoca, in the northeast part of Jones County. This producing horizon was discovered in 1937, in the Iron Mountain Oil Company's well No. 1 Olander, in sec. 196, B.B.B. & C. survey, at 3238 to 3250 ft. During the development of this pool, it was generally referred to as the Avoca pool. As a second pool has been discovered in the same producing zone, also near the town of Avoca, the writer has taken the liberty of changing the name of the original Avoca pool to Avoca-Olander pool. Forty producers had been drilled in the Avoca-Olander pool by the end of 1938; their initial ranged from 28 to 300 bbl. per hour. Stimulus was given to the interest in the development of the Palo Pinto limestone when the Ungren-Frazier No. 1 Griffin, in sec. 199, B.B.B. & C. survey, Jones County, found the limestone from 3225 to 3250 ft., with an initial production of 931 bbl. per day. (This new pool has been given the name of Avoca-Griffin pool, by the writer.) The best well to be completed, up to the present time, is the Bert Fields No. 1 Taylor in sec. 199, B.B.B. & C. survey, which had an initial production of 748 bbl. in 3 hours. The Owen-Snebold No. 1 McKeever in sec. 158, B.B.B. & C. survey, in northwest Shackelford County, added to the interest in the Palo Pinto limestone when it extended the Ivy pool with a well in the Palo Pinto limestone from 3145 to 3183 ft., and was estimated good for 6,000,000 cu. ft. of gas and 6000 bbl. of oil per day. During 1938, Stonewall County obtained its first commercial producer when the Stonewall Oil Co. in No. 1 Parriott discovered the Palo Pinto limestone saturated from 5169 to 5176 ft. and tested 371 bbl. per day. Two new producing horizons were discovered about 2 miles east of the old Noddle Creek pool, Jones County; the first, the Humble Oil & Refining Co. No. 1 Irvin, in sec. 48, block 18, T. & P. R. R. Co. survey, which had saturated limestone from 2550 to 2567 ft. and was good for 100 bbl. per day; the second, in the Humble No. 1 Horton, sec. 40, which

Jan 1, 1939

By Alexander Deussen

The figures listed in a table for Gulf Coast fields given by L. P. Teas1 in 1934 are so greatly at variance with results that I have obtained from a serious study of this subject over a number of years, that I am disposed to challenge the correctness of Mr. Teas' figures as an accurate representation of acre-foot yields of Gulf Coast fields, and as regards at least two of the fields listed by Mr. Teas I desire to "put into the record" some figures that, according to my study, are more nearly in accord with what I conceive to be the actual facts. Upon investigation I find that Mr. Teas' figures, inadvertently no doubt, arc not what they purport to be. Apparently the figures were arrived at by considering as thickness of the producing formation the net thickness of producing rock corresponding "to the total of the net portions of the producing zones which actually yield oil into the drill hole"—and in following this method I am under the impression that Mr. Teas was acting under instructions of the Institute in the preparation of this paper, in order to get comparable figures from the several fields of the United States. Apparently the author interpreted these instructions to mean that in the absence of cored thicknesses of producing horizons the actual number of feet of screen set in the various producing zones was to be taken as the basis for arriving at the thickness of these zones and the "acre-foot" yields. It is obvious that in many instances only 20 ft. of screen, or even 10 ft. of screen, might be set in a well, when there might be actually 100 ft. of oil sand present. In the early operations in the Gulf Coast it was usual to set much less screen than the amount of sand. It follows that the "acre-foot yields" so arrived at would be much greater than those found by using the full amount of sand. In Mr. Teas' table, it was indicated that up to the end of 1933 "acre-foot" yields had been obtained in the several fields as listed in Table 1. A casual inspection of these yields will show that certainly they do not properly reflect the amount of oil produced from an acre-foot of the

Jan 1, 1936

By J. R. Wylie, L. C. Huntley

Drilling for oil in the eastern producing states was fairly active during the first part of 1931, although less so than in 1930. With low prices development declined during the year, until the low prices of the summer resulted in an almost complete shut-down of drilling. This coincided with the action of the Conservation Board of the Pennsylvania Crude Oil Producers Assn, in limiting pipe line runs to 50 per cent of the 1930 normal for the Bradford district and upper country, and to 70 per cent for the balance of the region. Not only was new drilling halted but in many cases oil-producing properties were shut in. In November crude prices were partly restored, and all oil offered was being taken except in the Bradford district which was restricted to 80 per cent of the 1930 normal. During the latter part of the year drilling was being resumed on a moderate scale, and new production indicated a resumption of the proration order. The interest in gas development which has been under way for several years, maintained its supremacy over the search for oil in 1931. New reserves of importance were developed during the year in the Western Kentucky Coal Basin, in the Eastern Kentucky shale gas territory, in Stark County, Ohio, as well as the Oriskany sand development in northern Pennsylvania and central New York. A gas line was completed to the Eastern Seaboard serving Washington and Baltimore, and other lines were under construction designed to serve portions of the territory not hitherto supplied with natural gas. The low price of fuel oil at seaboard is understood to be the deterrent factor against further extension of natural gas lines to these markets at present. The development of these new reserves, as well as those developed by intensive drilling in old areas, resulted in the building up of large potential gas production and a lowering of rates paid to the producer. This, coupled with the country-wide tendency to lower the consumer rates of all public utilities, resulted in a general threat to reopen rate cases before various state commissions. Oil Development The past year was marked only by the almost complete shut-down of new development, reaching its low point during the summer, with its

Jan 1, 1932

By E. E. Barker

Although flotation was known to be a successful process prior to 1312, Utah Copper Co.'s ores were not entirely treated by this process until 1923. Experiments had been conducted, of course, prior to that time, and in February, 1917, the first unit of the Arthur plant was changed over from gravity concentration to flotation. On May 16, 1918, the entire Arthur plant was on flotation, excepting the coarse concentrate which was tabled prior to fine grinding. The reasons for the delay in adopting flotation at these plants were, first, that it was decided to await the outcome of the litigation with the Butte & Superior Mining Co., which began with an injunction served on Oct. 3, 1911. This litigation continued for years. Then the demands on the plants in the war years 1916, 1917 and 1918, really precluded any further drastic changes during that period, as all efforts were bent on maximum tonnage, and the cry of tonnage, rather than of recovery, was the major issue. The postwar depression followed these years of intensive production, so that it was not until 1922 that the Magna plant was equipped to use this process. Excepting, then, the amount of coarse concentrate that was tabled, 1923 was the first year when the Utah Copper Co.'s ores were on a full flotation basis. Effect of Flotation on Ore Reserves The object of this paper is to point out the effect that flotation has had on the operations of the Utah Copper Co. In 1905, when D. C. Jackling began making history in copper, the ore reserves were 34,000,000 tons, with a grade of 2 per cent. copper and a mill capacity of 700 tons daily. The point of cut-off between nonprofitable and profitable grades was 1.2 per cent. A few years later the capacity was increased to 6000 tons, when 1.1 per cent. became the point of cut-off. Ore reserves had climbed to 80,000,000 tons, having a grade of 1.9 per cent. In 1911 there was an ore reserve of 300,000,000 tons, with a grade of 1.5 per cent. and a cut-off of 1 per cent.; in 1918 the ore reserve was approximately 400,000,000 tons, and a grade of 1.38 per cent., and point of cut-off 0.95 per cent., based on normal costs and prices. Up to this

Jan 1, 1928

By R. A. Pallanch

SODIUM sulfite as a zinc retarding agent in the selective flotation of complex lead-zinc sulfide ores was discovered by the writer in the summer of 1919 in the testing laboratory of the U. S. Smelting, Refining & Mining Co.'s gravity concentrator at Midvale, Utah. It proved to be the first reagent to give consistently good results in the laboratory on the company's Bingham ore. In December, 1919, C. A. Lemke, concentrator superintendent, recommended that a flotation unit be added to the existing gravity mill to handle the mill slimes, using sodium sulfite as the zinc depressant. Owing to the poor lead and zinc markets and the unfavorable royalty schedules offered by the Minerals Separation Co., the project fell through at this time. In 1921, a number of laboratory tests were made at Midvale on other ores, among them ore from the Sunnyside mine at Eureka, Colo. Both sodium and calcium sulfites were used with success on this ore. Early in 1923, further tests were made at Eureka, shortly after the Sunnyside company had resumed operations after a two-year shutdown. As a consequence sodium sulfite was given a trial in the mill. The results showed sufficient improvement over previous work as to warrant continuous use of this reagent in the lead circuit. Except for a week or so in 1926 and for several weeks in April, 1927, when sodium cyanide and zinc sulfate were given trial runs in this mill, sodium sulfite has been used ever since. Sodium sulfite was chosen rather than the calcium sulfite because of its greater solubility, making it possible to introduce the reagent as a solution. This solution is introduced into the Marcy ball mills along with the original feed of ore. The consumption of sodium sulfite in the Sunnyside mill varies from ¼ to ½ lb. per ton of ore, the smaller amount probably being nearer the average. In February, 1924, laboratory work at Midvale demonstrated conclusively that good results could be obtained on the company's Bingham ore and on most of the custom ores tested by using sodium sulfite as the zinc depressant, xanthate as the lead enhancer in the lead circuit, followed by copper sulfate and additional xanthate to float the zinc. Sodium sulfide was used to float the iron pyrite after the lead and

Jan 1, 1928

By David Donoghue

THE. years 1901, 1910, and 1924 may be considered as the beginning of new eras in the history of the oil industry of the Gulf Coast of Texas and Louisiana. Spindletop, in 1901, with its enormous cap-rock production revealed the possibilities of the salt domes. The lateral sand development at Vinton, in 1910, renewed interest in the then known domes which were non-producing, or were producing from the cap rock or from sands above the cap rock. The discovery of three domes, Nash, Orchard and Long Point, in the year 1924, by means of the torsion balance and the seismograph, is the beginning of intensive explorations of the Gulf coastal plain by geophysical methods. Domes other than those mentioned have no doubt been found during the last few months of the year but tests have not been drilled to confirm the evidence of the instruments. DISCOVERY OF DOMES BY GEOPHYSICAL METHODS The Rycade Oil Corpn. operated the first torsion balance on the Gulf Coast in October, 1922, and the Roxana Petroleum Corpn. brought in one of these instruments and began work in December, 1922. The U. S. Coast and Geodetic Survey made some gravity observations at Damon Mound, in 1923, with a pendulum apparatus. In March, 1924, the Marland Oil Co. placed the first seismograph on the Gulf Coast and the Gulf Production Co. followed with one in May. In June, 1924, the Gulf Production Co. began operations with a torsion balance. The Atlantic Oil Producing Co., The Texas Co., and others have experimented with several types of instruments involving various principles. During the next few years, a great advance in geophysical methods may be expected, especially if one of the newly discovered domes should be productive. The first dome discovered was the Nash, in Fort Bend County, Tex., about 6 mi. east of Damon Mound. A slight elevation and two shallow wells containing sulfurous waters made the locality somewhat interesting from the standpoint of surface indications, and the torsion-balance measurements indicated the presence of a dome. On July 20, 1924, the Rycade Oil Corpn. No. 1 Wisdom encountered lime at a depth of 634 ft. and anhydrite at 639 ft. The hole was abandoned on Sept. 8, 1924, at 769 ft. in anhydrite. A cavity in the anhydrite caused much delay and the final abandonment of this test.

Jan 3, 1925

He took a great interest in technical matters and his inclination was strongly toward research investigations. At the same time he was effective in manual and mechanical work and was generally found working side by side with the men under his direction. His nature was unselfish and he was extremely popular socially. He was a member of the Coeur d'Alene Commandery, Knights Templar. Stanly A. Easton. Lieutenant.Louis Baird Louis Baird, a Lieutenant in the Royal Field Artillery of the British Army, died on the battlefield in 1915. Lieutenant Baird was born July 28, 1880, at Stirling, Scotland. His technical education was obtained at King's College, Melbourne, Australia, in 1893 to 1895, and at the Technical College at Glasgow, Scotland, in 1897 to 1900. After an apprenticeship with the Mexican J. & 8. Rec. Co. of Mexico, lasting from 1900 to 1903, he became mill superintendent for the Cia. Minera Benito, at Juarez, Zac. During the year 1905-6 he was assistant manager of the Caridelaria y Anexas, at Pinos, Zac., and from 1906 to 1907 was engineer with the Cia. Minera Jalisco, San Sebastian, Jalisco. At the time of his admission to the Institute, in 1908, he was practising as a mining engineer at Etzatlan, Jalisco, Mexico. For the next four years he practised his profession in the City of Guadalajara, Jalisco, removing, in 1913, to Ixtlan del Rio, in the State of Tepic. It was from here that he returned to England to put his services at the disposal of the British Government. The Institute is not definitely informed as to how, where, or when Lieutenant Baird met his death. iCaptain John H. Ballamy John H. Ballamy, Captain on the Regimental Staff of the 103d Engineers, was killed near Fismes, on Aug. 9, 1918. Captain Ballamy was born at Plvmouth. Pa.. in 1886 and graduated from' the High School of that town in 1903. In the following year he began work as a coal miner, and at the same time began the study of mining engineering in the evening and any other spare time. He continued this diligent and energetic practice for many years. For sixteen years he continued in the employment of the Delaware, Lackawanna & Western Rai1roa.d Company's coal mining

Jan 1, 1920

?AARONSON, ALFRED E, .Vice-Pres, Mid-Co Petroleum Co , Mid-Co Bldg, Tulsa, Okla '18 ABADIE, EMILE R, Min Engr - Box 927, Porterville, Cal '76 ||ABADILLA, QuiRiCo A, Student, Colorado School of Mines, Golden, Colo. '20 ABBOTT, CLARENCE E, Gen'l Supt, Iron Mines Div, Tenn Coal, Iron & R R Co , 1405 Minnesota Ave, Bessemer, Ala. '04 ABBOTT, Louis BENJAMIN, Chief Engr, Consolidation Coal Co-, Elkhorn Div, Jenkins, Ky '15 ABBOTT, ROBERT R Met. Engr, Peerless Motor Car Co, Cleveland, Ohio. '12 ABE, ASAKA Fujita Min Co, Dojima, Osaka, Japan '14 ABEEL, GEORGE H, JR, Cons Min Engr, 633 St Paul Ave, Los Angeles, Cal '18 ABEL, ALBERT E, Mgr., Pittsburgh Dist, Valley Mould & Iron Corpn, 28th St & R R Ave, Pittsburgh, Pa '19 ABEL, W D, Min. Engr. 3897 Sacramento St , San Francisco, Cal. '19 ABELL, 0 J, Pres & Treas, Abell-Howe Co, 332 South Michigan Ave, Chicago, Ill '19 ABERNATHY, G E Willow Springs, Mo '20 ABEY, HIROSHI, Min & Met Engr, Arakawa Mine, Mitsubishi Co, Senpoku-gun, Akitaken, Japan '17

Jan 1, 1923

Aamot, Olav Crone, Research Engr., Norsk Elektrokemisk Kongensgt, 18, Oslo, Norway ?29 Abbott, Clarence E., V.P., Charge of Raw Materials, Tenn. Coal, Iron & R. R. Co., 1242 Brown-Marx Bldg., Birmingham, Ala. '04 Abbott, Louis Benjamin, Chief Engr., Consolidation Coal Co., Watson Bldg., Fairmont, W. Va. '15 Abel, Raymond L., Asst. Prof., Dept. of Pet. Refin., Univ. of Pittsburgh Pittsburgh, Pa. '28 Abel, Walter D., Cons. Engr 364 S. Cloverdale Ave., Los Angeles, Calif. '32 Abele, Louis T 1457 Euclid Ave., Zanesville, Ohio. '31 Abell, Leo M Sullivan Concentrator, Chapman Camp, B. C., Canada. '31 Aborn, Robert H., Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. '19 Abraham, W. E. V., East India United Service Club, 16 St. James' Sq., London, S. W. 1, England. '28

Jan 1, 1936

Jan 1, 1978

By Herbert J. French

Herbert 1. French (Member 1934), vice president of the International Nickel Co. Inc., assistant vice president of the International Nickel Co. of Canada Ltd., and AIME Howe Memorial Lecturer for 1956, died in Rochester, Minn. on Aug. 17, 1955, after a long illness. Before his death, Mr. French had laid the foundation of research on which the Howe Memorial Lecture (p. 770) was based. His associates at Inco, 0. 0. Miller and J. W. Sands, were able to complete the project, present the lecture, and prepare it for publication, following Mr. French's general outline. Born in New York on May 27, 1893, he graduated from the School of Mines, Columbia University, with a degree in metallurgical engineering in 1915. Mr. French gained his early engineering experience with the American Smelting and Refining Co., serving as a chemist and as-sayer at the company's Murray, Utah, installations. He later returned east and became a metallurgical engineer for the General Vehicle Co., Long Island City, IT. Y., a subsidiary of the General Electric Co. In 1917 Mr. French was appointed civilian inspector of materials for the U.S. Army Signal Corps, and continued this work when it was later absorbed into the Bureau of Aircraft Production. Subsequently he was appointed district inspector in Philadelphia for the Pittsburgh (Ordnance Metallurgical) office, later transferring to Pittsburgh. After World War I Mr. French became an assistant physicist on the metallurgical staff, U. S. Bureau of Standards, Washington, D. C. During his years with the Bureau, he was successively associate physicist, metallurgist, senior metallurgist, and assistant chief, division of metallurgy. In 1929 Mr. French joined International Nickel as a metallurgist at the company's Bay-onne, N. J., research laboratory. Transferring to the development and research division, New York, in 1931, he took charge of alloy steel and iron development, becoming assistant manager of this division in 1943. Mr. French's appointment as an Inco vice president came in March 1947. Previously, he was appointed assistant vice president of the International Nickel Co. of Canada Ltd. in January 1947. Mr. French served the War Production Board during World War II as senior technical consultant in charge of the metallurgical and specifications section of the iron and steel branch. When this section of the WPB was organized into the steel division, he was appointed chief of the metallurgical branch. From March 1944 to September 1945 Mr. French served as assistant director. Herbert French was well known not only for his prolific contribution to the metallurgical literature, for which he received numerous awards, but also for his prolonged service to the profession through its technical societies. He was a past president of ASM, and was the Campbell Memorial Lecturer for that group in 1933. Mr. French was honored by the American Society for Steel Treating in 1931 when he was awarded the Henry Marion Howe Medal. A series of lectures he gave in 1941 before the Fourth Western Metal Congress in Los Angeles was later published in book form under the title Alloy Constructional Steels.

Jan 1, 1957

[A AALSETH Earl P (M 51) Consult Geol Engr 2019 Eldorado Dr, Billings, Mont ABADIE Henry G (M 43) Asst to. Supt of Oper Long Beach Oil Dev Co 925 Harbor Plaza, Long Beach 2, Calif. ABBET Waldo (A 56) Asst Diet Oper Supt Sun Oil Co P 0 Box 66, Stowelt, Tex ABBOTT Clifton T (A 60) Apartado 677, Maracaibo, Venezuela ABBOTT Fred E Jr (M 59) Abqaiq Diet Mgr Arabian American Oil Co Dhahran, Saudi Arabia ABBOTT J L (M 56) Partner Pritchard & Abbott 1010 Ft Worth Natl Bk Bldg, Fort Worth 2, Tex ABBOTT Richard H (J 51) Partner Abbott & Howard 422 W Hermosa, San Antonio 12, Tex ABBOTT William G (M 50) Div Mgr Rice Engrg &. Operating Inc Box 1142, Hobbs, N. M. ABDERHALDEN Ronald R (J 59) Prod Engr Continental Oil Co Box 100, Carml, 111]

Jan 1, 1961

Jan 1, 1907

By S. Floreen

Seven iron alloys ranging from 5 to 12 pct Ni and 5 to 14 pct Cr were studied. All alloys transformed to bcc massive martensites. Tempering increased the strengths , probably because of relief of residual stresses generated by the martensite transformation. The major strengthening mechanism appeared to be solid-solution hardening by nickel and chromium. Studies of the work-hardening behaviw, of the effects of prior austenite grain size, and of the effects of changing strain rate and test temperature gaue results very similar to iron or low-alloy steels. Increasing nickel contents markedly improved the toughness at subzero temperatures. Studies of the flow properties did not, however, indicate the reason for the beneficial effect of nickel on toughness. The marine atmosphere corrosion resistance of the alloys was improved primarily by chromium additions, but increasing nickel contents were also beneficial at low levels of chromium. J\ number of maraging and PH stainless steels are strengthened by precipitation hardening in a low-carbon Fe-Ni-Cr martensite matrix. To some extent the resultant properties of these steels must depend upon the properties of this matrix. The present study therefore was conducted to evaluate the transformation characteristics and mechanical properties of a series of Fe-Ni-Cr martensitic ternary alloys. A limited evaluation of the corrosion resistance of the alloys in marine atmosphere was also made. ALLOY PREPARATION Seven 100-lb air induction melts were prepared using electrolytic iron, nickel, and chromium metal additions. The initial Fe-Ni charge also contained 0.05 wt pct graphite to produce a carbon boil during melt down. After melting of the base charge, the heats were refined with 0.1 wt pct additions of manganese, silicon, aluminum and titanium and poured into cast-iron molds. The ingots were homogenized at 1250°C and uni-directionally hot-rolled to 2-in. plate. They were then homogenized another hour at 1250°C, and unidirection-ally hot-rolled to %-in. plate at a finishing temperature of approximately 1050°C. The compositions of the heats are given in Table I. Two additional heats were prepared as 40-lb vacuum-induction melts using electrolytic iron, nickel, and chromium metals, and commercially pure molybdenum chips. A carbon boil, and 0.1 wt pct additions of aluminum and titanium were again employed, but manganese and silicon were not added. The heats were converted to %-in. plate using the procedure described above. The compositions of these heats are included in Table I.

Jan 1, 1967