Search Documents

By Ralph W. Bailey, William B. Price

During the past three or four years, the fabricators of silicon-bronze alloys have endeavored to induce users of phosphor bronze to use instead the silicon-bronze alloys, claiming that the silicon bronzes are superior to the phosphor bronzes for switches and springs, or where high fatigue resistance is desired. This paper gives the results of tests comparing several phosphor bronzes with a 3 per cent silicon bronze and a copper-nickel-tin alloy (Adnic), all processed by the Scovill Manufacturing Co. So far as the authors are aware, sheet-metal fatigue tests have not been made on any of the alloys included in this report, except on one phosphor bronze, material C, Table 1, which was tested by Townsend and Greenall1. Endurance Limit The majority of fatigue tests are designed to determine the endurance limit of a material. The number of repetitions of stress that will serve to establish an endurance limit varies with different materials. For ferrous materials, H. F. Moore2 has shown that stresses that do not cause failure up to 10,000,000 stress cycles will not cause failure up to 100,000,000 (and sometimes to 1,000,000,000) cycles. Thus an endurance limit for ferrous materials can be determined with a minimum of 10,000,000 stress cycles. For nonferrous materials, no such generalization holds. R. R. Moore3 has shown that for manganese bronze and elektron metal, 13,000,000 and 28,000,000 cycles, respectively, will serve to determine an endurance limit, while certain duralumin specimens gave no indications of having reached an endurance limit up to 400,000,000 stress cycles. J. B. Johnson6 showed that an endurance limit for duralumin was not found by tests running up to 500,000,000 cycles. H. F. Moore2

Jan 1, 1937

By C. G. Dunn, K. T. Aust

SEVERAL studies1-10 have reported a type of grain boundary migration which occurs when a strained grain grows into an adjacent deformed grain during annealing. Beck and Sperry called this phenomenon strain-induced grain boundary migration, since the observed boundary movement, which takes place in a direction away from the center of curvature, is apparently motivated by the excess free energy of strain hardening. However, little information has been obtained on the detailed structural changes accompanying such grain boundary motion. The problem of driving force for strain-induced boundary migration was considered by Dunn and Daniels,' who used bent bicrystals of Si-Fe. They demonstrated that two grains of differing energy, in the form of subboundaries, behaved according to the concept that the low-energy grain would grow at the expense of the high-energy grain. Beck" reported experiments of Sperry for high-purity aluminum, which indicated that generally the particular grain of a pair which work-hardened more was invaded. The measure of work hardening here was

Jan 1, 1958

Jan 1, 1970

By C. P. Proctor, J. T. Crawford, John Griffen

TROUGH washers were among the earliest methods used for concentrating ores; they are referred to by Agricola about the middle of the sixteenth century as already being used while the hand- operated jigging sieve had only recently come into use. For cleaning coal the trough washer apparently was first used in France and Belgium about 184.1. The early trough washers were intermittent and the refuse at least was shoveled out by hand. The invention of a continuous jig washer, by a Frenchman, Berard, in 1848, acted as a stimulus to coal washings in jigs and retarded progress in trough washing in the nineteenth century. Chapman and Mott 1 describe a number of trough washers developed in England and on the Continent from 1850 to 1900, such as the Bell and Ramsay, Ramsay, Bell and Green, Wunderlich, Scaife, McLellan, Lodge, Elliott, Blackett, and Murton. The later of these removed the refuse mechanically, either intermittently or continuously, but in ways that interfered with stratification. THE RHEOLAVEUR A Belgian engineer, Antoine France, is responsible for the development of means to remove refuse materials continuously from a trough washer, while preserving stratification and preventing the loss of coal with the refuse. The methods and equipment devised, which have become known throughout the world as rheolaveur, were initiated at the St. Nicholas mine near Liége, Belgium, about 1912. This installation consisted of two units to wash 20 to 8-mill. (3/16 to 5/16-in.) and 8-mm. to 0 (5/16-in. to 0), each having only two superimposed inclined troughs. The first few "Rheo" boxes on the top trough removed refuse directly and the remaining Rheo boxes discharged impure refuse to the lower trough for rewashing. On the lower trough the first few boxes removed refuse and the following boxes removed a middling product used for boiler fuel or other purposes. The overflow of both troughs was joined to form the washed coal product.

Jan 1, 1950

By David Cole

At the time flotation appeared upon the metallurgical horizon in Arizona, the writer, under the direction of Dr. Ricketts, was engaged in remodeling and enlarging the No. 6 Concentration Plant of the Arizona Copper Co. at Morenci, and the work had been in progress nearly a year before the Inspiration experiments with flotation had disclosed the revolution in concentration that was at that time impending. The simplified flow sheet worked out for the remodeling of the Morenci plant had been based upon the removal of the freed metal in a minimum number of stages by treatment upon tables equipped with Butchart riffles, the latter being adapted to accomplish both classification of feed and removal of the metal at one operation, substantially as described in my previous paper.l The scheme of treatment for the slime was based upon the well-known fact that after copper sulphides, such as chalcocite and chalcopy-rite, etc., are reduced to a certain extremely fine state of comminution they are definitely beyond the reach of separation upon any of the concentrating devices then known. By using drag-belt classifiers (which served as conveyors as well as separators), the overflow ,would be of the usual "slimes" class. Experiment had shown that when these drag-belt overflows were properly diluted (that is, to about 5 to 7 per cent. solids in the feed under treatment) the very fine sand, and especially the very fine but still granular sulphide particles, would, if given a short distance to fall, quickly settle out in prime condition to yield an excellent recovery on vanners; a further valuable feature would be that the very fine non-separable final overflow tonnage might be discharged direct to tailing, thus conserving space requirements so as to permit within the old building, without embarrassment, the increase of capacity required. For reasons that are obvious, this kind of feed preparation for the slime could not be successfully accomplished in any form of pointed boxes or

Jan 1, 1917

By H. D. Newell

Jan 1, 1938

By H. D. Newell

Jan 1, 1938

By Alexander L. Field

The Bureau of Mines is investigating the problem of slag viscosity, its variation with the temperature and with the composition of the slag, and its effect upon the distribution of the sulphur between molten iron and slag, as introductory to a series of contributions to the theory of the metallurgical processes. The method of measurement, viscosity apparatus, furnace and other accessories mentioned in this paper have been described fully in s Bureau of Mines report.1 The Literature on Slag Viscosity The viscosity of blast-furnace slag had not been measured previous to the investigation described in this report. A number of investigators have determined the "fusibility," or softening temperature, of slags by means of the cone method .or other deformation method, but these methods supply only limited information regarding the temperature-viscosity relations of the slag in question. Any deformation method that may be employed indicates only the temperature at which the slag attains a more or less definite viscosity., the magnitude of the value obtained depending on the method used. For details of the various methods used by different investigators, see the Bureau of Mines paper already referred to. An isolated measurement by Doelter on a single mixture at 1,300" C. represents the highest temperature reached in the various viscosity investigations previous to those described in this report, in which results have been referred to absolute units. Arbitrary deformation tests have of course been made at much higher temperatures.

Jan 1, 1917

By E. S. Leaver

THE purpose of this paper is to describe, in a general way, gold-dredg-ing operations in California, with particular reference to unusual features, including types of deposits and recent attempts to improve the recovery of the gold. DREDGING AREAS The gold-bearing formations that traversed the western slope of the Sierra Nevadas for a north and south distance of some 300 miles furnished the immediate source of the gold found in most of the placer deposits of California.. Erosion through a long period carried the gold, together with various forms of partly disintegrated material, to lower elevations and formed placer deposits. Through the classifying action of water in motion, the coarser gold and heavier material of various kinds were deposited relatively near the source; consequently, in' the higher moun-tain country, old river channels were worked feverishly during the early California gold-rush days because of their high gold content. With the working out of these known high-grade channels, and from the knowledge thus obtained of prehistoric stream beds, drift mining was started and flourished until about 1890. Even today many drift mines are operating with the objective of opening other old Tertiary river channels that have been covered by volcanic flows.

Jan 1, 1937

By John M. Warde, Eileen P. Burke

ORES of manganese and chrome have a high order of strategic importance, both metals are basic to the metallurgy and usefulness of steel, the fabric on which our economy rests. Looking beyond the current recession and short range picture of oversupply in these ores, this review attempts to answer the following questions regarding the longterm outlook for these key commodities: By 1970, what will be the probable demand here and abroad, what are future supply prospects, and what effect is the USSR likely to have on the world market? (See summary forecast on facing page.)

Jan 8, 1958

By Christopher W. Schram, Allan B. Tanner, Frank E. Senftle, George R. Boynton, Philip W. Philbin

A borehole sonde using a 252Cf neutron source and a Ge(Li) gamma-ray detector was field tested in a coal bed in Belmont County, Ohio, to ascertain whether such a device could be useful as a coal-exploration tool. As the sonde was lowered into the borehole, successive spectra were accumulated over short time intervals. The intensities of the capture gamma rays from hydrogen and of decay gamma rays from aluminum were determined simultaneously in each spectrum. A log of the intensities versus depth shows the depth and thickness of the coal bed. With the sonde stationary at points above, in, and below the coal bed, capture gamma rays were measured to show the variation in concentration of certain elements. From the spectrum recorded in the bed, a complete ultimate analysis, the percent ash content, and the heat content were determined without recourse to an external standard. Delayed gamma-ray analyses of the core were also made on the surface in the vicinity of the borehole in a fixed-geometry irradiation facility wing the detector in the borehole sonde. The concentrations of 10 elements were determined by this method on a coal split from the drill core. These experiments show that it is feasible to use a 252Cf- Ge(Li) borehole sonde as an aid in coal exploration.

Jan 1, 1979

By D. W. Fuerstenau, S. Raghavan

This paper presents a brief summary of some of the thermo- dynamic aspects of flotation processes. Thermodynamic considerations that control interfacial and wetting behavior in mineral/water/air systems are discussed. Particular attention is given to the thermodynamics of collector adsorption.

Jan 1, 1976

By K. G. Davis, P. Fryzuk

WEINBERG,' in an investigation of solute distributions along unidirectionally solidified rods of dilute silver in tin alloys, concluded that, for rods of 2 mm diameter or larger, a very high degree of convective mixing takes place in the melt ahead of the advancing interface. Suggested causes for this mixing were (1) thermal convection, (2) convective currents set up by changes in fluid density associated with concentration gradients, and (3) currents set up by changes in volume during freezing. Evidence was presented that causes (2) and (3) were not primarily responsible for solute mixing. Further, convective mixing took place in horizontal rods with temperature gradients as low as 6°C per cm, putting doubt on the importance of thermal convection. In the present work, convective mixing is examined in melts with known initial solute distributions. The absence of a moving solid-liquid interface eliminates convection caused by volume changes on solidification. In the first experiment, three silica tubes 2 mm in diameter and approximately 20 cm long were filled with an alloy of 100 ppm Ag in tin (99.999 pct purity), placed adjacent to one another in a horizontal furnace, and solidified from one end at 1 cm per hr. A110, a Y emitter, was used as tracer. A few centimeters at the start of the rod were left un-melted, to determine the initial concentration Go. After solidification was complete, one sample was removed. The hot furnace was then brought back to

Jan 1, 1965

By R. I. Jaffee, F. C. Holden, H. R. Ogden

IN a previous series of papers, the results of studies made on various types of high purity base titanium alloys were presented. Included in this work were the Ti-Mn' and Ti-Cu' alloys, representative of sluggish and active eutectoid systems, respectively. The present paper gives the results of a simi- lar study made on Ti-Mo alloys as an example of a ß-isomorphous alloy system. Experimental Procedures Alloy Preparation—Six ½-lb ingots were prepared from iodide titanium and high purity molybdenum stock. The ingots were arc melted in a water-cooled copper crucible under an argon atmosphere. Each ingot was melted at least twice to insure homogeneity and complete solution of the molybdenum. This was done by inverting the ingot in the crucible and remelting completely.

Jan 1, 1957

By Oswald J. Heinrich

During the last twenty years much has been done to investigate and define the Mesozoic formatibn of the United States along the Atlantic States, as well as in' the Territories. The investigations of Professors Hitchcock, Emmons, Hayden, H. D. Rogers, and those now in progress in connection with the geologicd surveys of Penn-

Jan 1, 1879

By Roy Lindgren

SINCE the year 1643, when the first blast furnace in America for treating iron ore was built at Saugus, Mass., out of mica schist quarried in the neighboring district, the procurement of a suitable refractory for furnace lining has been a problem of concern to the operators of furnaces. The stacks built of mica schist continued to smelt iron ore until about 1836, when, according to F. H. Norton, the first firebrick were produced1, at Queens Run, Pa. Other writers speak of brick having been molded and burned in Massachusetts about the year 1834. In 1841, Andrew Russell began to produce medium refractory plastic clay brick near East Liverpool, Ohio, that were used for lining blast furnaces1. The well-known Kentucky clay-producing district was not opened up until the year 1871, but since then it has produced a large percentage of the linings for iron blast furnaces. While some strides have been made by the refractories industry during the 100 years that have passed since the first firebrick were produced, it has been only during the last two decades that any real progress has been made towards bettering the product, even though the method of production had improved. Perhaps the fault lies with the user of the brick rather than with the producer, for not sooner demanding a supe-rior product. During the past 15 years the tonnage produced per lining has increased from 500,000 gross tons to 1,000,000 gross tons, and now some furnaces are producing 1,600,000 gross tons and better on a single lining. It is true that enlarged capacity of furnaces and improved practice have accounted for some of this increase in tonnage, nevertheless better quality in firebrick must be given credit for its share. However, we are not yet ready to say that we have reached a maximum life of furnace lining. We believe that a better product can be produced and that the refractories industries of America will, through their extensive research depart-

Jan 1, 1936

By F. W. Lee

Historical-From the beginning of time, all ingenuity of mankind has been concentrated upon the methods of finding gold and unusual deposits in the earth. An illustration (Fig. 1) from the old treatise by Agricola, "De Re Metallica," published in 1580, will serve to show the im-plicit faith of that generation in divining methods. However, it was not until 1920 that real progress was made in prospecting by using the latest advances of the physical sciences. The public interest was stimulated by the successes of these methods on the part of commercial oper-ators, and governmental agencies received many requests for information concerning their relia-bility. There were also, in the late 1920's.high- pressure mine-promotion schemes which used geophysical methods in a very questionable manner, symbolized in Figure 2 as of 1928 by an elec-trified forked stick. Authoritative information concerning such practices for public protection was needed to curb such notorious undertakings. Dr. Scott Turner, then Director of the United States Bureau of Mines, thoroughly understood the situation and was first in the governmental de-partments to recognize the possible value of a study of modern prospecting methods. The Bureau of Mines began this investigation by employing Drs. A. S. Eve and D. A. Keys of McGill University for short periods in the summer in 1927. Their first publication [see 1 of "References" at end of paper] served to illustrate the fundamental scientific principles which underlie geophysical prospecting. This was followed by a second publication [21 giving the results of field-tests. In the light of the rapid improvements during the intervening ten years, these two papers take a historical position. Later a full-time position under Civil Service was planned by the Bureau of Mines for con-tinuous investigations and research concerning geophysics and its applications to prospecting. It was Turner's idea that. since the oil-industry had been making very rapid progress with good results, if mineral mining could also benefit to the same degree, it would be of great help to that industry.

Jan 1, 1940

The ten-year "supply-demand relationship" tables in this chapter for various mineral and metal commodities have been adapted from Minerals in the U.S. Economy, compiled by the Bureau of Mines, U.S. Department of the Interior, published in 1975. Acknowledgment is made to the Bureau of Mines for compilation of the tables. [ ]

Jan 1, 1976

By A. B. Parsons

NOT every organization on reaching the relatively ripe age of three score and fifteen can say with truth that its purpose and objects remain precisely the same as prescribed by its founding fathers. Of course, constancy of purpose may be something else than unalloyed virtue. It could merely reflect slavish worship of tradition, intellectual stagnation, or sheer inertia. On the other hand, it could establish the fact that the founders were men possessed of broad outlook, of prophetic vision, and of an acute sense of direction. In addition to charting the course with precision, the founders of the A.I.M.E. surely showed a flair for expressing clearly in a few words what others might say obscurely in many words. To quote verbatim from the "call" for the meeting, in 1871, the proposed organization was to have: "two great objectives: "First, the more economical production of the useful minerals and metals. "Second, the greater safety and welfare of those employed in these industries." This text underwent some refining on several subsequent occasions but today the ultimate product, as set forth in the Constitution reads: "to promote the arts and sciences connected with the economic production of the useful minerals and metals and the welfare of those employed in these industries by all lawful means." The original call was dated "Wilkes-Barre, Pa., April, 1871," and was signed by Eckley B. Coxe, of Jeddo, and by R. P. Rothwell and Martin Coryell, both of Wilkes-Barre, each of the three subscribing himself as "mining engineer." The authors proceeded to explain briefly just how it was proposed to achieve these objectives: "In European countries, where the arts of mining and metallurgy have long been the subject of the most careful study, no means have been found so effectual in attaining the end above proposed, as the free interchange of experience among those actually engaged in these industries; and this object has been accomplished mainly through the medium of `Institutes,' `Associations,' or `Societies,' composed of those engaged in these occupations, and by the periodical publication of `essays' or `papers' communicated to such societies by their members. "It must be evident to all practical men that the interchange of the varied experience

Jan 1, 1947

By Oscar Glaeser

THE purpose of this paper is to present specific applications of the fundamental principles of mine ventilation and the means that are at our disposal to accomplish the task of maintaining a healthful atmosphere in small mines and prospect openings.

Jan 1, 1936