Search Documents

By Will Mitchell, Ford F. Miskell, C. L. Sollenberger

Heat treatment of ore prior to comminution reduces power requirements for grinding, reduces grinding media wear, and improves recovery of iron values from a typical Minnesota magnetic taconite. Test data demonstrating this, as well as an analysis of the economics of commercial application of the technique, are presented. THE taconites in general are hard, tough ores, difficult to grind. Liberation of iron mineral constituents usually is accomplished by grinding the ore through at least 100 mesh, and often it has been found necessary to grind substantially through 325 mesh to achieve satisfactory recovery and grade in the concentration process. Because of the fineness of grind required and the enormous tonnages of material contemplated for treatment in the future, costs resulting from grinding media wear and power consumption, together with capital investment required for comminution, approach astronomical figures. Economy in any one of these elements per ton of material ground could very well reflect a considerable saving to the ferrous industry in yearly costs. With this in mind, the Research Laboratories of Allis-Chalmers Manufacturing Co. have launched a program to discover means of effecting this economy. The initial phase of the work as described here deals with a heat treatment of crushed raw ore, followed by thermal shock in cooling, for the preparation of rod mill feed. Several investigators1-" ave noted an improvement in the grindabilities of ores treated in this manner. One investigator2 subjected low grade iron ores to heat treatment in an electric furnace. Basing his conclusions on screen analyses of crushed products, he observed that treated ore was more easily crushed than the untreated. He reported that observation of the treated and untreated ore through a microscope revealed cracks following the grain boundaries in treated ore, whereas no cracks were present in untreated ore. However, few if any have quantified the improvement in terms of total hp hours saved, reduction of wear of grinding media, or reduction of capital costs of grinding equipment involved. By means of Bond rod mill and ball mill grindabilitiesh nd by comparative wear tests, the conditions maintained during this investigation have been definitely evaluated. Heat treatment experiments have been made on a batch scale in a muffle furnace, followed by continuous scale experiments in a rotary kiln under various conditions of temperature, atmosphere, retention time, and quenching to determine the combination that would give the greatest improvement in the grindability of a taconite without affecting adversely the magnetic susceptibility of the magnetite. From these data, relative costs have been calculated for grinding both untreated and heat- treated ore on a basis of plant capacity of 120 tons per hour. Heat requirements for a rotary kiln, as well as the kiln capacity required for the treatment, have been estimated. For these tests 50 tons of ore were obtained from the Aurora mine of the Erie Mining Co., Hibbing, Minn. The ore was reported7 to have been selected from the magnetic portion of the lower chert horizons. An average chemical analysis of' this portion is shown in Table I and an approximate mineralogi-cal analysis is shown in Table 11. No attempt was made to differentiate between the various silicates because the compositions vary widely on the different horizons and depend on the degree of oxidation. Minnesotite, however, is the predominant silicate. The siderite grains were dispersed throughout the ore but were essentially associated with the rock-forming minerals. In a series of preliminary tests in which batches of —6 mesh ore were heat-treated in a muffle fur-

Jan 1, 1953

By D. Turnbull, R. E. Cech

THE supercooling behavior of pure liquid metal droplets has been described.' The solidification behavior of small droplets of Cu-Ni alloys as a function of composition is described herein. The Cu-Ni system is of interest for such an investigation because the components are miscible in all proportions in both the liquid and solid state and the phase diagram of the system, Fig. 1, is a type often encountered in metal systems. It was noted by Van Riemsdyk2 and others that the nature of the "blick" of gold droplets during assaying is not perceptibly affected by the content of the platinum group metals that are soluble in both liquid and solid gold. With the exception of these very qualitative observations there appear to have been no prior investigations of the supercooling of alloy droplets. A series of nine alloys varying in composition by 10 pct (nominal weight) steps was made using certified OFHC copper, 99.996 pct purity, obtained from the American Brass Co., and electrolytic nickel pellets, 99.92 pct purity, obtained from the International Nickel Co. The alloys were melted and cast in vacuo in a high frequency induction furnace. Segregation was minimized by chill casting into 1-in. diam steel molds. Each alloy rod was homogenized at a temperature 50°C lower than the solidus for 100 hr in dry hydrogen. Samples for solidification experiments and chemical analysis were machined from the same portion of each rod and at a depth of in. from the rod surface. A Car-boloy tool was used in taking turnings to minimize contamination of sample by the cutting tool. As a check, a number of samples for microscopic observation were chipped from the ingot with a fragment of pyrex glass. The resultant data in all cases agreed, within experimental error, with the data obtained from machined turnings. A number of small particles, 30 to 50 micron diam, of a Cu-Ni alloy were placed in a quartz vial 1/32 in. diam x % in. long. This was inserted into a platinum ribbon heater and mounted in a high temperature microscope stage. The general procedure followed in inserting samples into the stage and measuring the temperature of melting and solidification was the same as described in an earlier paper.' A chromel-alumel thermocouple was used to study alloys of 88.93 pct Cu, 80.62 pct Cu, and 72.27 pct Cu. A platinum-10 pct rhodium thermocouple was used for the remainder of the alloys. Procedure The assembled high temperature microscope stage was first evacuated and the sample given a 2 min in situ treatment at 900 °C in dry hydrogen to remove surface oxides which might otherwise catalyze crystal nucleation. After this treatment the atmosphere was changed to purified helium and melting and solidification were observed microscopically. It was not possible to determine the solidus with certainty. However, the liquidus temperature was measured very accurately since the surface of the particle changed in appearance from coarse and uneven to smooth, mirror-like within a few degrees. The visually determined liquidus temperature was checked by finding the highest temperature to which the particle could be heated such that it did not supercool upon lowering the temperature. This temperature which checked within experimental error with that found by observing surface change was assumed to be characteristic of the thermody-namic liquidus. In order to minimize the effect of selective evaporation of copper from the alloy, samples were changed frequently and the droplets were heated no more than 50 °C in excess of the liquidus temperature T,. When the latter conditions were fulfilled, T, values were reproducible. After melting, the temperature was decreased slowly until the particles solidified. The sudden release of heat of fusion on solidification caused the

Jan 1, 1952

By Maurice E. Peloubet

This discussion of accounting will describe the statements and the information that the accounting system produces, from the point of view of those who use such systems rather than of those who prepare them and who do the detail and technical accounting work. In any well organized mine, quarry, or other enterprise exploiting a mineral deposit, no matter how small, some clerical and accounting work must be done. Miners and other employes must be paid, supplies must be purchased and issued, and various tax and information returns, which even the smallest enterprise must file, have to be prepared. In this chapter it is assumed that the enterprise has employes of this type and that they understand the fundamentals of record keeping and accounting. It would be impossible here to give sufficiently full explanations to enable a man with no previous clerical and accounting training to set up and operate an accounting and cost system for even the simplest extractive operation. Rather, we shall hope first, to tell the investor and the operator, from the chief engineer or president down to a subforeman, what to expect from the accounting statements and records and how to use this information in his daily work; and second, that it will enable the man with some knowledge of accounting or bookkeeping, but with little or no experience in any extractive industry, to set up and operate a satisfactory system for a mine or other extractive enterprise. For readers who wish to go further, the bibliography at the end of this chapter contains many references. The emphasis has, therefore, been placed on the statements to be produced and the purposes for which they are to be used rather than the underlying books and records. These are, with a few exceptions which will be described later, essentially what might be found in any industrial enterprise and would probably, in the extremely small enterprise, consist of handwritten journals, ledgers, analysis books, payroll books, and stores ledgers. In the larger enterprise, various types of mechanical accounting would be introduced in proportion to the complexity of the operation.

Jan 1, 1959

By F. A. Schaufelberger

Early work on chemical precipitation of metals from metal salt solutions is reviewed. The chemistry and thermodynamics of precipitating copper, nickel, cobalt, and cadmium metals by reaction with hydrogen are discussed. Mechanisms of metal precipitation, nucleation, growth, and agglomeration are reviewed, as well as some solubility phenomena of gases and solids at elevated temperatures. Experimental data presented deal mainly with the reaction of copper sulfate solution with Hz.

May 1, 1956

By C. J. Bechtoldt, H. C. Vacher

Quenched alloys, prepared by powder metallurgical techniques, were examined by microscopic and X-ray diffraction methods. The compositions and heat treatments were chosen so that the chromium and nickel solvuses could be determined and a range of composition and temperature, in which a eutectoid had been reported, could be explored in small intervals. The results showed no evidence of eutectoid reactions having taken place. ALLOYS containing iron, chromium, molybdenum, and nickel are extensively used in high-temperature applications. In order to provide basic information on the solid-state reactions that occur in such alloys, the National Bureau of Standards is engaged in an extensive study of the equilibrium phases in the binary, ternary, and quaternary systems involving these four metals. Attention was directed to the chromium-nickel system because a review of the literature showed conflicting data. A recent compendium1 of the constitution of binary alloys gives two diagrams for the chromium-nickel system, one a simple eutectic and the second a diagram showing a eutectoid and a eutectic. The eutectoid was the result of an allotropic transformation in a high-temperature solid-solution form of a chromium-rich phase called 0. The approximate temperature and composition of the eutectoid was 1200°C and 30 at. pct Ni. In the preliminary study, at the Bureau, no transformation was indicated in the chromium-rich phase of ternary and quaternary alloys in which chromium and nickel were major components. Similar results have been reported from time to time in the literature,2-8 In consequence of this situation, a systematic study was made of the constitution of heat-treated chromium-nickel alloys using metallographic and X-ray diffraction methods. The compositions of the alloys were selected so as to determine the boundaries of the chromium-rich and the nickel-rich phases and to explore in small intervals the ranges in composition and temperature in which the eutectoid had been reported. The results of this study are reported and discussed in the present paper. EXPERIMENTAL PROCEDURES Materials, Alloys, and Heat Treatments—The alloys were prepared by a powder metallurgy technique similar to that used in earlier work.9 Analyses of the materials used are given in Table I. Powders were mixed using a vibrator in 30-g batches of predetermined composition; 2-g pellets were made from the mixture by compacting at room temperature in a 1/2-in. diam mold under 60,000 lb per sq in. pressure. The pellets were sintered in dry hydrogen for 10 days at 1300°C. At the end of the sintering treatment the specimens were quenched in water, which caused a pale green film to form on the chromium-rich alloys and thin black scale to form on the nickel-rich alloys. The pellets after sintering were approximately 1/2 in. diam by 3/32 in. thick. The purification train9 was modified by inserting a tube of titanium turnings, heated at 700°C to increase the efficiency of the removal of oxgen and nitrogen. It was found in the earlier work that the sintering treatment lowered the carbon, oxygen, and nitrogen contents of chromium-rich alloys to 0.01, 0.01, and 0.004 wt pct, respectively, and that there was a loss of chromium. In order to ascertain the extent of this loss, the chromium contents of certain alloys were determined chemically. They included those alloys used to determine the parameter-composition curves and those of critical composition, used to determine the chromium-solvus microscopically; these analyses were made on samples after the final heat treatments. The mixed powder values for the chromium content of those alloys that were not analyzed were adjusted to conform to a smooth curve based on the chemically analyzed values for

Jan 1, 1962

[MUNOZ, P.: New Oil Fields in Trinidad, M27, 311 MUNRO, C. H., biography, M84, 354 MUNROE, H. S., biography, M83, 277 Muntz metal (See also 60:40 Brass): corrosion. See Corrosion of Metals. fatigue and corrosion-fatigue, 78, 597 heat-treated: cleavage structure, 83, 498, 505 grain growth, abnormal, 83, 503, 505 machinability, 99, 323 stress-corrosion cracking, 89, 249. 266 MURAKAMI, T.: iron-silicon diagram, 80, 253, 255 MURDOCH, J. A. W., biography, M28, 157 MURDOCK, W. J.: Discussion on Adaptability of Various Coals as Generator Fuel in Manufacture of Water Gas 78, 561, 565, 566, 568 MURPHY. D. W. AND CHIPMAN, J.: Solubility of Nitrogen in Liquid Iron (T.P. 591) 116, 179. Abs., YB35, 33; M35, 114 MURPHY, L. J.: Relative Advantages and Costa of Electric Power in Lease Operations 77, 219]

Jan 1, 1936

By K. B. Nowels

The attainment of efficient flooding to a large extent depends upon a knowledge of fluid movement through porous media and the pressures used in controlling this movement. Little has been understood con-cerning the fundamental principles involved in the forced drive of water-flooding and an attempt will be made to present some data which may be of interest. Considerable data and technical information pertaining to natural and artificial water-flooding have been presented in the past by Torrey, Umpleby, Fettke, Panyity and others. Their papers have thoroughly covered the description of past and present-day methods of oil recovery by flooding in the Bradford field, especially an article by Torreyl in the Petroleum Engineering Handbook. A bibliography of papers devoted to watcr-flooding, published in Mr. Torrey's article, is appended to this paper. No attempt has been made, therefore, to describe the installations and procedure necessary in flooding, thus permitting the writer to deal exclusively with the mechanics of water movement in flooding operations and its relationship to well spacing. Artificial water-flooding will probably always be the most successful in oil fields described by Herold as being under "capillary control"" and will probably be useless in fields naturally under hydraulic or volumetric control. The natural water drive in an oil field under either of these two controls may give efficient recoveries, as a result of the regulated encroachment of edge water. Such a "natural flood" resulting from the influence of edge water must not be confused with the term as used in this paper, however. Any reference to "natural flood" will here refer to the old method of flooding formerly used in the Bradford field. This was discovered largely by accident and utilized the hydrostatic pressure created by a column of water standing in a watered-out oil well in forcing the oil to an adjacent producing well. The same principles are involved in either natural or artificial flooding, and the latter method simply

Jan 1, 1933

By Franz Fohr

On July 27, 1919, there passed away a simple, unassuming gentle-man, who, throughout his life, allowed his intense modesty to keep him-self in the background and during his later years effaced himself so thoroughly that but few of his acquaintances knew aught of him. Yet he was one of our accomplished metallurgists, who did good work in the practice of his profession and lived an upright life. Now that he is no longer with us Franz Fohr cannot plead to be overlooked, and those who fondly remember him will be gratified by his receiving his due. Franz Fohr was born, Sept. 7, 1838, in Mannheim, Germany. Of his ancestry, education, and early career we know scarcely anything. We do not even know just when he came to America, or. what led him hither. The first record of his professional work in this country, found among his papers, shows that from July, 1870, to Jan. 1, 1872, he was superin-tendent of the Newark Smelting & Refining Works, then owned by Ed-ward Balbach & Son. At that time the Balbach works at Newark, established in 1850, and the Selby works at San Francisco, established about 1866, were the only important silver-lead refineries in the United States. Mr. Fohr may have been associated with the Balbachs for some time before he became superintendent of their plant or he may have come from Germany but a short time previously. At all events, it is certain that he was at that time an experienced and accomplished metallurgist. After leaving Newark and going to San Francisco, he soon formed a connection with Thomas H. Selby & Co. Early in 1874-this firm sent him to New York to procure information respecting the manufacture of white lead. His engagement in New York terminated on-Jan. 31, 1875. During 1875, Mr Fohr spent some time at Silver Islet and in the Lake Superior copper region, but of his work there no record remains. In the latter part of 1875, or early in 1876, he associated himself as metallur-gist with the Boston Silver Co., operating at Saint John's, Summit County, in which William L. Candler, of Boston, was the moving spirit. That company was developing its mine in 1875. At the end of that year it "had about 800 tons of ore on hand, about three-fourths of which is dress-ing ore, to be concentrated in its very systematic establishment and to be smelted into pig lead." Evidently Mr. Fohr was engaged for the latter purpose. Henry A. Vezin, erudite and painstaking, was the mechanical engineer for the company. In the fall of 1876, Anton Eilers took his family for the first time so far West as Denver and Mr. Fohr went with them. I do not think that Mr. Eilers had any connection with the Boston Silver Co., save possibly in a consulting capacity, but he visited Saint John's and the enduring friendship among Eilers, Fohr, and Vezin, which terminated only with their deaths, dated from that time.

Jan 12, 1919

William M. Courtis, Detroit, Mich. (communication to the Secretary*):—I have a few items to add to the history of the Lake Valley mines. In December, 1879, I was sent to the Bassic mine of Colorado and then to Lone mountain, near Silver City, N. M., and to various copper-camps in Arizona. I staged from Glorietta, N. M., to Tucson, Ariz., stopping at Silver City to see the Cosette mine. This mine led to the opening of the Lake Valley mines, and is a deposit of similar formation. New Year's day, 1880, found me crossing the Rio Grande above the Jornado del Muerto. At Aleman, Victorio's band crossecl four hours ahead of us. We picked up four wounded soldiers to take to Fort Bayard, for during the day the colored troops under General Hatch had been driving the Indians back through the San Andreas mountains. The traveler of to-day little realizes the dangers of these trips, when over very rough roads we made about 100 miles in a day and a night. I subsequently made this trip six times, up to 1882, and each time I missed an Indian attack by from one to four days. The day I arrived at Silver City news had come of the massacre of 75 women and children at the San Francisco ranch. The fighting-men of' Silver City had gone to rescue others. I was the only passenger from Socorro, N. M., until we picked up the soldiers. The next day we came suddenly on 5 of Victorio's band, but we had picked up several miners, so our stage bristled with guns, and we mere let alone. At or near my stone quarry, 6 miles from Socorro, 9 men, were killed by the band that, a day or two after, killed George. Daly, Lieutenant White, and all their men. During this raid, our miners and women at the mine slept in the tunnel. At the Cosette mine I had 35 men at work. These Indian raids had

Jan 1, 1910

Energy conservation has been the keyword in many plant expansions. Far many years, most of the phosphate industry has been dry grinding their phosphate rock. Agrico Chemical in Florida has recently been evaluating the wet grinding of phosphate rock, a process which eliminates a pre-dry stage for mill feed while allowing higher through- puts. This same company also plans to open a new phosphate facility in Louisiana that will use wet grinding in both ball mills. The Eveleth Expansion Co.'s Fairlane concentrator will have the largest rod and ball mills in the US mining industry. The plant will consist of three lines, each with one rod mill and one ball mill, and will process 464 ltph. The rod mills will be 15 x 20% ft, drawing 2035 hp. The ball mills will be 17 x 41½ ft, drawing 6900 hp and driven by dual 3000- hp motors. The plant is scheduled for startup in the fall of 1976.

Jan 2, 1975

By George Espey, George Sachs, G. B. Kasik

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By G. B. Kasik, George Sachs, George Espey

IT has been reported frequently that the hardness and strength vary over the cross section of cold-worked, particularly cold-drawn, material. Brass rod and wire usually have been found to possess a maximum strength and hardness near the surface.1,2 According to Sachs,' the center fiber has about the same strength as a wire stretched by the same amount in a tensile-test machine, the strength increasing toward the surface (Fig. I). These differences are particularly large for wire given a small reduction on drawing through a die with a wide opening. However, with increasing reduction and hardness, a tendency to form a thin soft surface skin becomes apparent. On the contrary, copper wire has usually been found to possess a soft surface skin3-5 and it has been reported by Harris3 that during the cold-drawing of hot-rolled wire the surface layer becomes increasingly softer than the core, while the layer of maximum strength moves toward the core, it being found near the surface at first. The increase of strength and hardness from the core to the skin is readily explained by the observation that, in addition to the stretching, the layers of a rod or wire are sheared more the closer they are to the surface.1,6-8 However, the presence of a soft surface layer can be attributed only to an annealing effect. The source of such a softening might be the extremely high temperature that originates from the friction between

Jan 1, 1942

By George Moore

IN spite of many investigations of the occlusion of hydrogen in iron, the nature of the process and the reasons for the accompanying effects upon the metal are still open questions. This is in large part due to three causes: (1) the difficulty of obtaining iron of adequate purity as starting material; (2) the occurrence of allotropic transformations, which compli-cate the effects; and (3) the fact that the body-centered cubic modifica-tion does not lend itself readily to crystallographic investigation. The present paper attempts a critical review and correlation of the somewhat scattered and disconnected existing observations, and an experimental determination of the extent to which the conclusions that appear to follow from these are applicable to iron of really high purity, studied under well-defined conditions.

Jan 1, 1939

By R. L. Doan

WHEN the Plutonium Project was started in the spring of 1942 there was no technology to produce uranium metal of the required purity. Not only was there no such metal available; no one knew how to make it or fabricate it after it was made. Since this time vast technical effort has been ex-pended in the atomic energy field. A short 15 years later the metallurgy of uranium is probably better known than that of any other metal, with the possible exception of steel. At the beginning of the 1942 drive to obtain pure uranium metal the most available raw material was black uranium oxide (U3O8) of about 92 pct purity from the Great Bear Lake region of Canada. It took only three months for the project chemists to develop a process for bringing the purity of this oxide up to 99+ pct and another three months for Mallinckrodt Chemical Co. of St. Louis to build the purification plant and get it into operation. In early summer of 1942 the purified brown oxide (UO2) started moving to the Metal Hydrides Co. in Beverly, Mass., and to the Westinghouse Research Laboratory in Bloomfield, N. J., both of which had been granted Government contracts to try to make pure uranium metal.

Jan 9, 1957

By E. F. Ketterer, D. B. Collyer, A. B. Wilder

The microstructural stability of 59 carbon and low alloy steels after 34,000 hr exposure at 900' and 1050°F, including the weld heat-affected zone, is discussed. The tensile and creep rupture properties of the parent metal of many of the steels before and after 10,000 hr exposure are presented. SEAMLESS pipe has been used for many years at elevated temperatures. When seamless first began to be used, operating temperatures and pressures were relatively low and the steel produced adequately met the existing requirements. The need for knowledge of creep properties and graphitiza-tion was nonexistent. Today the requirements for tubular products have changed considerably. Operating temperatures and pressures are increasing continually and corrosion, particularly at high temperatures, presents a problem. Carbon steels have, under these conditions, certain economic advantages particularly in oil refinery use. However, the use of low alloy steels in the generation of steam power has increased appreciably due to the influence of molybdenum on creep strength and the control of graphitization with chromium. The behavior of carbon and certain low alloy steels after long periods of exposure at 900° and 1050°F (480° and 565°C) has been investigated. The steels were examined before and after 10,000 to 34,000 hr exposure. Results obtained with material exposed at 1200°F (650°C) are not presented due to the severe oxidation and resulting decarburiza-tion after long periods of exposure. The graphitization characteristics of carbon and low alloy steels are of fundamental concern to the users of these materials. This is particularly true where welded joints are employed. In order to evaluate properly the behavior of steels at elevated temperatures, it is desirable to employ not only long periods of exposure under controlled conditions, but to use material with known properties and steelmaking practices. The purpose of this investigation has been to study the microstructure of the weld and the tensile and creep rupture properties of the parent metal after long periods of exposure at elevated temperatures. In the report'.' of a previous investigation data were presented on the microstructure, impact strength, hardness, and oxidation characteristics after 10,000 hr exposure at elevated temperatures. When this investigation was planned, methods for controlling the graphitization characteristics of steel were not established and, therefore, a number of special alloy steels were included in the study. During the exposure of these steels, the influence of aluminum in accelerating the rate of graphitization and the inhibiting power of chromium were established by various investigators. Also, the vanadium-bearing steels, because of their outstanding creep properties, received attention. As a result of these developments, considerable progress has been made in the field of high temperature tubular products, and the necessity for special alloys to prevent graph-itization has been restricted largely to the use of chromium. Material Chemical analysis, deoxidation treatment, and austenitic grain size of the 59 steels discussed in this paper are shown in Table I. The steels were forged to 1x1 in. bars with the exception of steels 12B, 12DX, 12DY, 12DZ, 70, 70A, 72 to 78, 82, and 83 which were machined from heavy wall pipe. All bars were surface ground before exposure. Heat treatment before exposure is shown in Table 11. The majority of the steels included were melted in either a basic open hearth or basic electric furnace; how-

Jan 1, 1955

By G. Sandoz

A simple diffusion-couple experiment was carried out for the purpose of determining whether chromium in sufficient amounts would cause the cementite phase in cast irons to become thermodynamically stable with respect to graphite and austenite at 1750°F. The implications of the results to some current theories on graphitization mechanisms are discussed. The literature abounds with evidence that chromium retards the decomposition of cementite to graphite and austenite or ferrite, for example during first-stage and second-stage graphitization in malleabilizing white cast irons and the subcritical graphitization of steels. Efforts to explain this retarding action of chromium have been conjectural, however, because the mechanisms controlling graphitization kinetics in the absence of chromium have never been clearly established. Concerning rate control, there are basically two schools of thought: 1) that graphitization rates are limited by diffusion potential (the stability of cementite relative to graphite, and 2) that graphitization rates are limited by diffusivity of Fe, C, Si, vacancies, and so forth.5'10 Chromium then, is thought either to increase the stability of cementite or to retard some critical diffusion process.

Jan 1, 1960

By Charles Barron McIntosh

BECAUSE of the well known relationship between a low atmospheric pressure and increased amounts of methane in coal mines, attempts have been made to find associations between low pressures and coal mine explosions. An early study by F. Able disclaimed this relationship. He found that half the explosions took place during a rising barometer when methane content in a ventilated mine would be decreasing. A more recent study by C. L. Hosler revealed a close relationship between anthracite mine explosions and low atmospheric pressure. Bituminous coal mine explosions, where coal dust as well as methane can be exploded, were found to be more closely associated with a rising pressure following a low barometer than with the falling or low pressure period. Emphasis on rising pressure periods led the present writer to investigate the effect of the post-frontal or post-cyclonic weather on coal dust. Dust samples of uniform mesh were exposed in an Illinois mine. Analyses of the dust taken before and after the passage of cold fronts and their accompanying low pressure troughs indicated an increase in coal dust moisture prior to a frontal passage and loss of moisture from coal dust following the time of lowest pressure. Thus the warm, moist air (Tropical Maritime)found over the mine during the falling pressure period was cooled in the mine and moisture added to the dust. Cold, dry air (Polar Continental) accompanies' the rising barometer following a frontal passage and the air, being heated in the mine, subtracted moisture from the coal dust. A similar but seasonal phenomenon occurs from summer to winter, the dry dust period in winter being recognized as the more dangerous period. The question arose as to how the short period or daily changes in moisture content of coal dust compared with the seasonal changes. Temperature and humidity statistics were obtained from the surface and mine entry for the months of July andJanuary. The gain and Ioss of mdisture. to the hine were calculated for these two morths as were the gain and loss associated with mT (Tropical Maritime) and cP (Polar Continental),air masses as observed in the investigatiynsl. Temperature and humidity statistics tigatiynsl.taken from [the two air masses represent atimp span of only 34 hr. The redultant changes as presented in the accompanying table verify the supposition that short period changes in coal mine moisture may attain the magnitude of recognized dangerous seasonal changes. Statistics for the mT air and the July air have been placed next each other and those for cP and January air together for easier comparison of the two warm and two cold air units. The last column readily reveals that there is little difference in the amount of moisture being deposited in the mine from the mT air and the July average air. A similar conclusion is reached regarding the loss of moisture from the mine when it is affected by the cP air mass or the average January air. This comparison would be particularly true from late fall through early spring when strongly contrasting air mass changes are a common occurrence. The invasion of cold, dry air following a cold front thus produces a drying period that could well receive more attention as a danger period for coal dust explosions. This drying period would compare with Able's explosion period during a rising barometer. The drying period is also perltinent in Hosler's findings, where it was noted that the average explosion day (for bituminous coal mines) followed the day of lowest atmospheric pressure. Moreover, the author's investigation of some 365 coal mine explosions also indicates that this post-frontal period should receive special attention in connection with mine safety measures. Two comparatively recent major explosions in Illinois (Centralia and West Frapkfort) occurred after the mines had been under the influence of cold-dry air for 25 to 30 hr-following a deep low pressure passage. Dust was the important explosive element in both these explosions.

Jan 1, 1958

By G. K. Dumbauld, B. E. Morgan

Kesults of laboratory investigations of the effects of drilling muds on oil well cements are presented which show that relatively large quantities of untreated muds do not seriously interfere with the setting of cement slurries, but that relalively small quantities of treated muds seriously retard the setting of cement slurries. Laboratory results also indicate that the harmful effects of contamination with treated muds can he counteracted by the addition of activated charcoal to cements. Also described is the successful use of cement containing activated charcoal for the placement of plugs in oPel hole after previous attempts with ordinary cement had been unsuccessful. INTRODUCTION The contamination of cement slurry by dilution with drilling mud has long been considered a cause of failure in oil well cementing. The cement slurry must displace the drilling mud from the annulus between the casing and the walls of the borehole. and it is probable that some mixing of the slurry and the mud occurs even under the most nearly ideal displacement conditions. Hole enlargement, failure to center the casing in the hole, and formation of gel structure in the drilling mud increase the probability of contamination. In some cementing operations, such as the placement of a cement plug in open hole, considerable mixing of the mud and slurry is likely. Many cement failures which can be attributed logically to no cause other than contamination of the cement slurry by the mud attest the need of a better understanding of this problem. Considerable attention was given to the problem of mud contamination of cements about 20 years ago.The effects of field mud upon cement slurries prepared with different amounts of mix water were investigated thoroughly, and the data obtained were invaluable in determining the causes of the high percentage of failure in oil-well cementing at that time and in bringing about improved cementing results. Since then, many aspects of the problem have changed, due primarily to advancements in cement and drilling mud technology. Today, several types of portland cement are used in well cementing and numerous chemical additives are used in drilling muds. An excellent report on the effects of drilling mud additives on oil-well cements was issued during 1951 by the American Petroleum Institute. Data in the report revealed that many mud additives, notably organic materials in relatively small amounts, produce a marked effect on the properties of cements. Prior to this time, little information has been available on the effects of chemicals commonly used in the treatment of drilling muds upon the properties of cements. Another aspect of the problem of mud contamination of cements, which has received no attention heretofore, is the possibility of producing a cement having properties unaffected by a reasonable amount of mud contamination. In view of the need for additional information on the contamination of present-day cements by currently-used drilling Muds, the investigation described herein was initiated Several years ago with a two-fold purpose: first, to determine the capacity of cement slurries to tolerate contamination by both untreated and treated muds without loss of ability to set and develop strength within a reasonable time; and, second, to investigate the possibility of enhancing the ability of cement slurries to withstand mud contamination by incorporating additives in the cement. The data for this study were obtained by mixing drilling mud with cement slurry and testing the resulting slurry-mud mixture for rate of set and development of strength. Also, several materials were tested for their possible improvement of the property of cement slurry to withstand mud contamination; these materials were tested in both contaminated and uncontaminated cement slurries.

Jan 1, 1952

By R. G. Gifkins

Mean boundary migration depended linearly upon creep extension under various conditions. Prolonged annealing or air-casting increased the proportion of immobile boundaries at a given stage of tests. Grain growth during annealing followed a power law. The linking of migration and sliding in creep and models for migration are examined; activation energies are calculated from these models. Segregation of oxygen to boundaries appears to be a controlling factor. THE idea that boundary migration and boundary sliding during creep are linked has often been suggested,'-5 especially when evidence has been obtained for an alternation between the two processes. In simple bicrystals sliding can occur without any migration6 but in more complex bicrystals7 it is observed. McLean' and Couling and Roberts 5 made measurements of both sliding and migration; McLean concluded that there was no linking of the two processes whereas Couling and Roberts supported the idea. McLean' also developed a model for migration during creep and annealing. The present work was initiated as part of a study of the recrystallization of lead during creep9 but has been extended to examine some aspects of the mechanism of migration. MATERIALS AND METHODS Specially refined high-purity lead* was used; the total of impurities, excluding oxygen, was 0.0008 wt pct. Oxygen was removed as far as possible by melting in vacuo, treating at 550" to 600°C with hydrogen and then casting at 450°C under a vacuum of 10-2 mm Hg; the oxygen was then believed to be 0.00005 wt pct. Specimens were made from extruded strip and then annealed at the required temperature in an air oven, controlled to 5 lac. They were then polished in a mixture of acetic acid and hydrogen peroxide. At this stage some specimens were etched to give grain contrast and their grain sizes determined by the intercept method. Migration of boundaries during creep was measured on the surface of polished (not etched) specimens, directly loaded at room temperature (22°C) or 50°C (52"C) to initial stresses of 300 to 700 1b per sq in. Twenty six vacuum-cast hydrogen-reduced specimens were used and, in addition, two specimens were from material air cast after hydrogen reduction ("partial" air cast) and two from air-cast material not treated with hydrogen ("full" air cast). Duplicates were made in the majority of tests. At intervals through the creep tests, specimens were unloaded and the migration measured, normal to the direction of migration at the point of measurement, for each boundary along standard traverses. Usually between 110 to 180 boundaries were measured at each of some twelve stages of the tests. Migration was measured on the projected image (X100) using prism illumination. Fig. 1 illustrates the method of measurement and shows the kind of variation of migration found from boundary to boundary and along particular boundaries. Fig. 2 gives an example of more extensive migration. The mean value of distance migrated was generally reproducible to *10 pct but occasional points gave a scatter of *20 pct. The correctibn applied by McLean8 to allow for the contribution sliding makes to the apparent distance of migration could not be used, for the sliding at most boundaries was too small to measure with the equipment available. There were two reasons for supposing the correction unnecessary in the present work;

Jan 1, 1960

By J. Bruce Wagner, Roger L. Levin

Lattice-parameter measurements have been carrzed out at room temperature on undoped and on chromium-doped wustite as a function of oxygen concentration. Results may he expressed by for the undoped uustite. These data are in agreement with and extend the work of' Jette and Foole. The present results are consistent with the cation vacancy model. for metal- deficil wuslite, both undopen and doped. SEVERAL investigators have made room-temperature lattice-parameter measurements on wustite as a function of composition. Jette and Foote used these measurements to determine the phase limits of wustite. Willis and Rooksby and Benard have also measured the lattice parameters of wustite at room temperature, but their values of a. vary considerably from those of Jette and Foote. In conjunction with Studies' on the transition from surface-controlled heterogeneous reactions involving CO-C02 oxidation of metals, lattice-parameter measurements on undoped and chromium-doped wiistite have been performed. These studies are especially needed to clarify conflicting data of previous authors, to extend the data to the stability limits of wiistite as determined by Darken and urr,6 which include a larger range of existence than that found by Jette and Foote, and to test by X-ray means the role of chromium as a vacancy producer in wiistite.

Jan 1, 1967