Search Documents

By Gail Moulton

THE oilfields in Illinois are located principally along the LaSalle anticline in the southeastern part of the state. The oil produced comes most largely from beds of Pennsylvanian and Mississippian age, but there is an increasing important production from deeper horizons, as will be noted under new development. The oil is largely of paraffin base, and has an average specific gravity of about 35° Baume. The rank of Illinois as an oil producer has dropped from third since 1913, when its production was exceeded only by that of California and Oklahoma, to eighth in 1923. This has been the result of failure to find new pools of considerable size to offset the declining production of the old wells and of the greatly increased production of some of the other states. The noteworthy features of petroleum production in Illinois during 1924 are: the low rate of decline for the state as a whole; the smaller percentage of dry holes; and the larger average initial yield of the new wells.

Jan 3, 1925

By M. L. Brashears

IN the last 15 years industrial use of ground water has more than doubled, and in 1951 amounted to 5 billion gallons per day. A similar sharp increase in the utilization of ground water for irrigation and public-water supply occurred in the same period. In many areas rapid increase in withdrawal from wells has taken place almost entirely unhampered by regulatory control and with little or no integration of effort. As might be expected, the chief interest in many regions has been maximum production rather than sustained perennial yield. As a result, widespread depletion of underground reservoirs and deterioration of the quality of the water stored in them has taken place in many areas, even though total pumpage in the United States is far below ultimate potential. Of even more concern is the fact that excessive withdrawal has drawn salt water into the reservoirs beneath many heavily populated centers along the Atlantic, Gulf, and Pacific coasts, causing costly abandonment of pumping plants.1

Jan 10, 1953

By T. H. Janes

NATURAL abrasives of some type are found in all countries of the world. In order of their hardness the principal natural abrasives are diamond, corundum, emery, and garnet, which are termed high grade, and the various forms of silica, including pumice, pumicite, ground feldspar, china clay and, most important, sandstone. The properties qualifying materials for use as abrasives are hardness, toughness, grain shape and size, character of fracture, and purity or uniformity. For manufacture of bonded grain abrasives such as grinding wheels, the stability of the abrasive and its bonding characteristics are also important. No single property is paramount for all uses. Extreme hardness and toughness are needed for some applications, as in diamonds for drill bits, while for other purposes the capacity of the abrasive to break down slowly under use and to develop fresh cutting edges is of greatest importance, as with garnet for sandpaper. In dentifrices, soaps, and metal polishes, of course, hardness and toughness are objectionable.

Jan 10, 1954

By Charles M. Haas

WHEN minable ore has been located, the problem of mining is synonymous with the problem of movement --movement of men and equipment to mine the ore, and movement of the ore from the earth to the mills. In slusher drifts and shafts, on shovels and dragline excavators, on churn drills and bulldozers, wire rope is essential to the transportation of men, ore, overburden, and equipment. Although a casual glance creates the impression that all wire ropes are alike, there are crucial differences between ropes. Strand diameter, number of strands, weave, core, and resistance to corrosion all decide the type of job a wire rope can do, and where and how long it can do that job. These factors are, of course, the responsibility of the rope manufacturer. Beyond this, he can extend his function into the mine itself by advising users on the use, care, and maintenance of these sinews of the mining industry. This article, then, covers both the manufacturing and end-use aspects of wire ropes.

Jan 9, 1951

Open pit operators have found the dropball crane a great aid in cutting costs and hazards of secondary breakage. But a common problem in using the unit has been with the shock absorbing connection from the cable to the dropball itself. Blair Limestone Div. of Jones & Laughlin Steel Corp. has come up with a new connector to solve this problem and to save the time usually lost in frequent replacement of the cable slings, chains, or old tires hitherto used at this point. J&L personnel solved the problem by combining three ideas from other dropball crane owners. Their unit consists of two long U-bolts running through a heavy spring originally made for use on a vibrating screen. Heavy duty swivels attached to the bent ends of the U-bolts provide attachment points for the crane cable and the special chain to the dropball. Connection at the dropball is by an eyelet welded directly into the mass of steel, and a special alloy chain is connected to this with a clevis.

Nov 1, 1955

By H. E. Sadler, Prof. Silliman

The research here recorded was undertaken early in the present year, and has been prosecuted steadily for about eight months. While the work has been under my constant supervision and advice, the labor has all been performed by Mr. Sadler, to whom is chiefly due the development of the successive steps which have led to the final result. The process is better than I dared to hope, and we are able to place at the command of chemists and engineers interested in the matter an apparatus of continuous and uninterrupted action, and methods of analysis by which the daily averages of the two variable and inconstant factors of illuminating gas, ammonia and sulphur, may be determined with all needful accuracy, even by those little skilled in chemical manipulation, and with very little loss of time. This research has been carried out in the laboratory of the New Haven Gaslight Company.

By A. V. Henry, W. Harry Vaughan

THE kaolins of the southeastern United States were known to civilization as early as the latter part of the eighteenth century-and yet the [ ] commercial history of Georgia kaolins may be said to begin in the year 1900. The U. S. Bureau of Mines reported for that year a production of 6885 tons of "miscellaneous" clays in Georgia. A comparison of these figures with those of 1934, when the production rose to 284,556 tons (65 per cent of the domestic production), indicates the growing economic and technologic importance of this raw material. Fig. 1 clearly shows that a part of the increase is due to a normal growth in the use of kaolinitic clays and a part is due to replacement of clays formerly imported. Occurrence Georgia kaolin occurs in an irregular belt extending diagonally across the middle of the state, a distance of approximately 225 miles. This belt

Jan 1, 1937

By Joseph W. Murray

Prior to 1950 Magma's ore production came from two parallel, steeply dipping, east-west striking mineralized faults, one called the Main or Magma vein and the other the Koerner vein, which lay about 1100 ft to the south. This vein system has been explored and mined over 9000 ft horizontally and 4800 ft vertically. In 1950 continued exploration led to the discovery and development of replacement orebodies in the Devonian limestone zones adjacent to the veins. These replacement deposits occur in the eastern part of the Magma mine and follow the strike and the 30º east dip of the host limestone. Strike length of the ore bodies varies from 250- 500 ft and thickness from 15-125 ft. The orebodies are large tabular masses with chalcopyrite and bornite being the dominant ore minerals. Hematite and pyrite are the most abundant gangue minerals. Incompetent limestone, shale, or a porphyry sill hanging wall is characteristic of portions of the replacement beds. In many instances the ore is blocky, badly fractured and intermixed with layers of limestone gouge, pyrite and hematite.

Jan 6, 1973

By Gill Montgomery

The strong upward curve of fluorspar consumption continued through 1968, with domestic producers unable to furnish more than 30% of U.S. requirements. Stocks of all grades were quite short at all points during most of 1968. This resulted in price increases as both domestic and foreign producers sought to cover spiralling labor costs. Further increases are probable for 1969. All Illinois mines were closed by strikes in January and February. The strong trend in metallurgical imports reflects the increased use of fluorspar in steelmaking, as new oxygen process steel plants come into production. The growth of use of all fluorocarbon chemicals continues to require additional acid grade fluorspar, with military uses a major factor. Several new aluminum smelting facilities coming into production are adding to the aluminum fluoride needs, bringing further pressure upon the world supply of acid grade fluorspar. The world-wide consumption pressure on all grades of fluorspar is pushing prices up, and no end to the tight supply is in sight, even assuming that all the new projects cited here are finished on schedule.

Jan 3, 1969

By A. T. Janssen

Production planning of direct-shipping ore from a number of relatively small deposits serves to sequence development and mining of these deposits so that both long- and short-range demand can be met while the timing of development cost is such that the average annual rate is minimized. Hand-computed methods have the disadvantage that they require substantial effort and time and cannot be exhaustive. The application of operations research and computers not only overcomes these disadvantages, but opens up additional applications, such as feasibility studies involving alternative mining strategies and changes in the ore market. The method employed concerns linear programming and specifically the Big-M algorithm applied to the variant on the simplex technique with penalties applied to deviations from the desired ore grade. Acceptable 20-year production schedules could be generated in relatively little time, i. e. , in less than 200 seconds for the central processor of the Control Data Corporation 6400 system of the University of Colorado in Boulder.

Jan 1, 1969

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By Milton E. Wadsworth, W. Martin Fassell, William H. Dresher

A study of the rate of dissolution of molybdenite (MoS2) in alkaline solution was carried out under carefully controlled conditions. Effects of temperature, oxygen over-pressure, and KOH concentration were evaluated. Studies were made in the temperature range 100°C to 175°C and in the pressure range 0 to 700 psia of oxygen. Under these conditions molybdenite was found to leach according to a linear mechanism. Both oxygen over-pressure and KOH concentration were found to control the rate of leaching. The mechanism has been explained in terms of adsorption of oxygen at the molybdenite surface followed by configurational rearrangement of the adsorbed molecules. The hydroxyl ion dependency is believed to be diffusion-controlled. Laboratory batch studies have shown that molybdenite can be readily dissolved in alkaline solutions under moderate conditions of temperature and pressure. Commercial application of this process to the production of ferro-molybdenum and molybdenum chemicals is promising in view of the ease of dissolution of molybdenite and the relatively noncorrosive conditions involved in the process.

Jul 1, 1956

By O. W. Ellis

The writer has dealt with the effect of various methods of melting copper upon the gas content of the metal.' The copper referred to in his earlier paper was melted in the foundry both in the oil furnace and the electric furnace. As the metal did not measure up to conductivity standard, the term "casting copper" was applied to the material in the title of the paper. It was thought that some information in regard to the gases in a sample of overpoled copper might also be of interest, and through the courtesy of C. R. Stevens, superintendent of the copper mill of the West-inghouse Elec. & Mfg. Co., such a sample was obtained. The metal was chill-cast in the form of an ingot about 7 in. long, 2 1/2 in. deep (from the base to the raised surface of the ingot) and from 1 3/8 to 1 7/8 in. wide. A photograph of part of the ingot is shown in Fig. 1. The effect of over-poling on the surface of the metal is here quite clearly shown.

Jan 1, 1929

By Henry Logan

THE purpose of mine-hoist safety con-trollers is to prevent hoists from being operated at speeds above those considered safe and expedient, to ensure proper accel-eration and retardation near the ends of travel, and to prevent overwinding. In other words, they are to safeguard the normal speeds and movements of the hoist-ing drums and cages. The object of this paper is to explain the fundamental principles of hoist controllers, and to aid in their selection, installation, and maintenance. There have been many designs of me-chanical hoist controllers, the basic ele-ments of which as ultimately developed consisted of a flyball governor and another movable member supported by a frame and arranged to move in a vertical, horizontal, or rotary direction, depending upon the particular design, the whole mechanism arranged to be driven in synchronism with the hoist drum. In case of overspeeding, inadequate retardation, or overwinding, a pawl or catch controlled by the governor would engage teeth or dogs on the moving member, which through mechanical con-nections would cut off the power and set the brakes.

Jan 1, 1940

By R. Varbanov, D. Nikolov, I. Nishkov

An interesting new flotation technique which reportedly improves mineral recovery over an extended particle size range-from 3 mm to 5 microns and below-has been developed by the Institute of Physical Chemistry, Bulgarian Academy of Sciences. Designated the "static" flotation technique, it is suited for upgrading tin, molybdenum, tungsten, uranium, gold, copper, lead, zinc, and other metallic ores. Recoverable nonmetallics include feldspar, sulfur, and phosphorite. Characteristic of the static flotation process are: •longer contact period (up to 1000 times longer between particles and bubbles, •low collision velocity and inertial forces between the contact and aeration in a thin pulp layer, • aeration without the harmful hydrodynamic repulsion upon particles below 5 microns (the pulp layer is only a few millimeters thick and rising bubbles collide with the particles either directly or in the thin foam films formed), •option to conduct the process with or without froth by film flotation at equilibrium contact angles, and • the use of inexpensive frothers and/or unstable froth with separate regulations of froth stability by hydrodynamic, ultrasonic, or electrostatic means.

Jan 10, 1979

By M. D. Arnold, P. B. Crawford, P. C. Hall

An experimental study has been made to determine the optimum flooding pressures for four different oils. The oil formation volume factors ranged from 1.08 to 2.13, and solution gas-oil ratios ranged from about 200 cu ft/bbl to 2,250 cu ft/bbl. Viscosities ranged from 0.38 to 0.95 cp at the respective bubble points of the fluids and from 0.7 to 20 cp at atmospheric pressure. Water floods were conducted at various pressure levels from run to run. The recovery as a function of flooding pressure was found to be different for each fluid, with optimum gas saturations ranging from 7 up to 35 per cent. The data indicate that substantially higher recoveries may be obtained if water floods are conducted at an optimum pressure and that this optimum pressure is a function of fluid properties. The same core was used for all tests, and the reproduction of saturations for various runs indicates that wettability in the predominantly water-wet core did not change. INTRODUCTION A paper was presented by Bass and Crawford' which described an experimental study of the effects of flooding pressure and rate on oil recovery by water flooding. This work was conducted using high-pressure models operated in a manner similar to that of an actual reservoir, with gas saturations being obtained by a solution-gas-drive mechanism. They found that the greatest oil recovery was obtained for the system studied by flooding in the presence of a 5 to 7 per cent gas saturation. Another experimental study simulating field conditions was presented by Richardson and Perkins.' They used an unconsolidated sand pack containing kerosene-natural gas fluid and interstitial water. They flooded at various pressures and flooding rates. For their system it was found that the recovery was independent of the pressure level at which the water flood was performed. Kyte, et al," found that oil recovery by water flooding was increased as the free gas saturation at waterflood initiation was increased. However, after the initial gas saturation was increased above 15 per cent, the increase in oil recovery tended to level off. All of their runs were made at the same pressure using a light oil saturated with helium. The desired gas saturation was obtained by injecting helium into the core. Dyes' made calculations which showed that an optimum gas saturation of 12 to 14 per cent may result in an increase in oil recovery of 7 to 12 per cent over that obtained by flooding at the bubble-point pressure. Others have also found that the presence of a free gas saturation may increase the waterflood oil recovery. In each case shrinkage was small and changes in fluid properties with respect to pressure were small. A careful review of the literature reveals that at the present time there is a wide difference of opinion on the factors affecting waterflood recoveries. This diversity of opinion is probably due to the fact that very little research has been done which has taken into account the many variables existing in an actual field being water flooded. Since the literature contains little information on high-pressure waterflooding studies using various types of reservoir fluids, it was believed appropriate that such a study should be made. EQUIPMENT AND PROCEDURE All tests were made using the same consolidated sandstone core. Torpedo sandstone was used to turn a cylindrical core 13.5-in. long and with a 2.92-in. average diameter. The core had a porosity of 28 per cent and a permeability to brine of 146 md. This brine was made up by adding 20,000-ppm sodium chloride and 30,000-ppm sodium nitrite to distilled water. This was used as connate water and flooding water. No fresh water was ever brought in contact with the core, as tests showed the sandstone contained argillaceous material which swelled in the presence of fresh water and plugged the stone. The core was sealed in a section of 6-in. N-80 tubing with Woods metal filling the annulus. The core was mounted horizontally; an injection well was placed in the center of one end and a production well in the center of the other. Pressure control was maintained by placing a back-pressure regulator (upstream control) on the producing well. The "live" oil was stored in a separate bottle and water was injected into this bottle to displace the oil for saturating the core using a two-cylinder standard-proportioning pump. This same pump was used for water flooding the core at a constant rate. This system was enclosed in water jackets and the temperature was automatically main-

By J. T. Burwell

THE crystal orientation in silicon iron that has been given a particular treatment described by Goss,1 has been studied by Goss, by Bozorth2 and by Sixtus,3 but their results do not agree and are almost entirely qualita-tive. The following pages give a description of the orientation of the crystals in the material as determined by means of X-rays and expressed graphically in a pole figure. The treatment consists of hot-rolling the material into strip and then giving it two cycles of cold reduction followed by recrystallization. This produces remarkably good properties in the rolling direction, the product having a maximum permeability in this direction of more than 25,000 and a permeability at 16,000 Gauss of more than 2200, It is now generally agreed that Goss's original conclusion' that the crystals in the final product are randomly oriented was incorrect, since Bozorth2 and Sixtus,3 using different methods, have shown that there is a decided preference in orientation. Those writers, however, expressed their results only in terms of one or more ideal orientations with deviations therefrom.

Jan 1, 1940

By C. F. Jr. Park

HOG MOUNTAIN is in the north central part of Tallapoosa County, Alabama, about 13 miles northeast from Alexander City. The Hog Mountain Mining and Milling Co. controls 1658 acres of land and is the only company operating in the district. The principal mine workings are in sections 10 and 15, T.24N., R.22E. The region has been visited by geologists many times, has been briefly described in several papers,1 and mentioned in many others. No detailed map of the mine or vicinity has been published. The field work for this report was started in March, 1934, as part of the Public Works reemployment program. About a month and a half was spent mapping both the surface and underground geology. The mine owners and operators have cooperated in every way possible to facilitate the work. N. 0. Johnson, the mine engineer, E. W. Ells-worth, J. E. McCoy and J. G. Englebert have acted as assistants for part of the work. The University of Alabama and the State Geologist's office have aided materially by permitting free use of their libraries and laboratory equipment.

Jan 1, 1935

By B. C. Scott, A. Baker

The Pitch mine of Pinnacle Exploration, Inc. is in the Marshall Pass district, thirty miles east of Gunnison, Colorado. This is a new mining district, having come into existence as recently as 1955, when uranium mineralization was discovered rather late in the days of the uranium boom. There have been three other mines in the district, all of them now inactive. Two of these produced a few hundred tons of very high-grade uranium ore, and the third, Pinnacle's Little Indian 36 mine, produced a few thou- sand tons of lower grade ore. Pinnacle was one of the first companies in the district, and was able to acquire a large acreage. The first two years of exploration were essentially wasted in looking for Plateau-type deposits in a mineralized sandstone bed, but this "wasted" work produced two specific items that paid off. One was an ore-grade outcrop that ultimately became the Little Indian 36 mine, and the other was a boulder of very high-grade uranium ore that eventually led to the discovery of the Pitch mine; however, the actual source of the boulder still has not been found.

Jan 5, 1961

By J. B. Scuffham, G. I. Warwick, J. B. Lott

The development of solvent extraction processes over recent years has led to their application on an increasing scale in metal extraction plants. The author's company has recently been awarded a contract for the design of the world's largest solvent extraction plant based on pump-mix mixer-settlers. The plant is designed to extract copper from a leach liquor and has an aqueous throughput of 12,000 imperial gpm. The design is based largely upon data obtained from the company's own research laboratories, where work has been undertaken on mixer impeller design, baffle design. settler area, organic entrainment recovery, etc. Investigations have been conducted into the effects of mixer impeller speed, recirculation rates, phase continuity, phase ratio, etc., on extraction efficiency, settler area, and organic entrainment losses. The implications of the results of this work on the design of a large plant using pump-mix mixer-settlers are discussed and the techniques used in overcoming certain scaling problem are outlined.

Jan 1, 1973