Search Documents

Last spring the suggestion was made that the national engineering societies offer to assist the War Department in the formation of an engineer reserve in the United States Army. The suggestion was brought to the attention of some of the officers of the Army, who commended it and confirmed the belief that the need of such a reserve was a real one; that the European war had distinctly shown that engineers in time of war are required on a scale never before realized and of great varieties of experience. In our own army no adequate provision is made for great numbers of engineers, for although the corps of engineers is composed of men of the very highest professional proficiency in certain lines it is greatly short of the numerical strength that would be immediately required. Acting on this suggestion, the American Society of Civil Engineers, the American Institute of Mining Engineers, the American Society of Mechanical Engineers, the American Institute of Electrical Engineers and the American Institute of Consulting Engineers appointed committees authorized and directed to take such steps as might be advisable to urge the organization of such a reserve corps as part of the. regular army, and so assist in putting the United States in a better condition of prepared-

Jan 10, 1915

Four generations ago, the Mount Morgan ore deposit sustained the hurly-burly of frantic development common to the finding of a rich discovery. In this case, it was gold discovered in gossan capping on one of the hills of the Dee Range. The bonanza ore, like the flush of youth, has been spent. Today, one recognizes in this operation the orderly manner of the senior citizen, keeping up with the times and husbanding resources. As mining towns go, Mt. Morgan has an enviable situation. The approach is from Rockhampton, Qld, a peaceful, affluent agricultural and cattle center near the sea. To reach the mine, one goes 22 miles, first across farming country, passing orange groves and occasional children on horseback. The ascent into the Dee Range is winding and rapid. In the winter, the hills are green and Bougainvillaea and flowering yellow bracken grow wild on the hillsides. Around a bend, the brown waste terraces of the mine come into view, rising above the surrounding country. The top of the mountain has been sawed off and a deep pit sunk into the core. A little further on, around a few more curves, the town of Mt. Morgan is seen nestling comfortably in the hollows, reaching up the slopes.

Jan 10, 1964

By O. C. Wheeler

There was a marked increase in the investigation of undeveloped areas in Colombia during 1936. The Shell company commenced geological and geophysical investigations on an intensive scale in the Upper Magdalena Valley and at the end of the year had several geological and geophysical parties working in that area. These investigations were supplemented by aerial photography and it is understood that negotiations are under way for having this work continued. The Shell is reported to have acquired some options and leases on private properties in the Upper Valley region and in the western part of Cundinamarca. The Socony Vacuum was making preparations to begin seismograph work on its property north of the Sogamoso River, acquired in 1934 from Sefior Luciano Restrepo. This company will probably start drilling on the property during 1937. The Richmond Petroleum Co. (Standard of California) is said to have renewed geological investigations in the Upper Magdalena Valley above Honda. Local Colombian interests took an active part in applying for concessions on nationally owned lands in the area between the Carare and Magdalena Rivers. The application of the Sociedad National del Carare for a concession in this area was granted during the year. Subsequently an agreement was reached between this

Jan 1, 1937

By N. B. Hoffman

Much of the drill steel produced in America is manufactured into hollow rods. After all forging has been finished the entire bar should be thoroughly annealed and heat treated before the point is hardened and tempered, at least where the drill has heavy duty, such as working in deep holes and hard rock. A large number of tools of like character and doing work requiring similar properties are now being made of alloy steels; for instance a steel with a carbon content of 0.75 to 0.85 per cent., manganese 0.25 to 0.35, phosphorus under 0.020, sulfur under 0.030 and vanadium 0.18 to 0.23 has proved very satisfactory for chisels. A steel of this type properly manufactured will be far superior to the ordinary carbon steels, while at the same time is one whose price range should not prove prohibitive. Much of the cutting efficiency of a drill depends on proper heat treatment. This vanadium steel has a far greater safe hardening and forging range than ordinary carbon steels, making it more nearly foolproof. It will harden nicely at 1400" I?. but will also harden well and satisfactorily at 1550" F. retaining its quality of hardness and toughness in either case.

Jan 1, 1922

All branches of our profession may look back 'with pride upon the patriotic service rendered by engineers during the war. That war has been won. The mortal danger which it threatened has been averted. But the effects of the torture inflicted by it still remain, a fever in the blood of the body politic. Fever begets delirium and, unless its course be checked, has a tendency to produce convulsions. The only safe course is to take immediate steps to allay the fever. The seat of the present trouble is industrialism; as production is at the foundation of civilization, a diseased condition there carries pain and consequent unrest into every member of the organism. Who shall supply the cure? Quack doctors, nostrums in hand, rush forward from all directions promising to perform miracles. But sane men know that no miracles, though invoked by star gazers of purest intention, will prevent or accelerate the orderly operations of the laws of nature and of human life. Delirium must be controlled by the firm, gentle hand of intelligent, sympathetic authority. Fever must be allayed first by removal of all poisons from the system, then by consistent ministration of cooling, quieting restoratives, then by simple, wholesome nourishment. Nature will, under such treatment, supply the permanent cure.

Jan 12, 1919

By Oliver B. Hopkins

Peru produced approximately 15,838,610 bbl. of oil during 1938, which was 1,618,406 bbl. below its production during 1937. As in recent years, the entire output of the country came from the La Brea-Parinas, Lobitos-Restin, and Zorritos fields, which are all situated along the northwestern coast. Outside of the proven areas, the drilling of test wells was continued by the Peruvian Government on the reserved zone near Zorritos. Six wells have been completed or are drilling. Of these one is a gas well at 2619 ft. and one is dry at 1415 ft. It is reported that three standard and two rotary rigs are being used. In southern Peru, in the Pirin region north of Lake Titicaca, the Government made a geological study of the National Reserve. In eastern Peru, the Cia. Petrolera El Ganso Azul continued its activities in the montana region, where its first well was reported to have had a show of oil at 1000 feet. There was also renewal of leasing activity in eastern Peru, where approximately 380,000 acres of new leases were filed on near Contamana. La Brea-Parinas Estate.—Production of crude oil on this property of International Petroleum Co. Ltd. amounted to 13,137,988 bbl. which was

Jan 1, 1939

By Oliver B. Hopkins

Peru produced approximately 15,838,610 bbl. of oil during 1938, which was 1,618,406 bbl. below its production during 1937. As in recent years, the entire output of the country came from the La Brea-Parinas, Lobitos-Restin, and Zorritos fields, which are all situated along the northwestern coast. Outside of the proven areas, the drilling of test wells was continued by the Peruvian Government on the reserved zone near Zorritos. Six wells have been completed or are drilling. Of these one is a gas well at 2619 ft. and one is dry at 1415 ft. It is reported that three standard and two rotary rigs are being used. In southern Peru, in the Pirin region north of Lake Titicaca, the Government made a geological study of the National Reserve. In eastern Peru, the Cia. Petrolera El Ganso Azul continued its activities in the montana region, where its first well was reported to have had a show of oil at 1000 feet. There was also renewal of leasing activity in eastern Peru, where approximately 380,000 acres of new leases were filed on near Contamana. La Brea-Parinas Estate.—Production of crude oil on this property of International Petroleum Co. Ltd. amounted to 13,137,988 bbl. which was

Jan 1, 1939

J. E. JOHNSON, JR., New York.-It seems to me that it ought to be somebody's job to tie these notch tests with the reversed-stress tests, because the thing that causes failures in structures, in a great majority of cases, is where the material is stressed repeatedly up somewhere near the elastic limit, and the repetition of that stress seems to bring about what I suppose you may call a growth of crystals and that eventually develops into a break. It seems to me that it would be of the greatest value if there could be a coordination of the results of a shock test of some kind with the reversed-stress test, so that we could be sure that a material that had shock-test resistance would have reversed-stress resistance. H. F. MOORE,* Urbana, Ill.-The question raised by the speaker concerning the correlation of results from impact tests of notched bars with the results of repeated-stress tests is a very complicated one. Impact on a specimen sends energy into the specimen, and if the specimen absorbs this energy without fracturing there must be developed both stress and elongation. A notch in the specimen allows but little elongation to take place before rupture, and develops the ductility of the

Jan 5, 1919

By John V. Beall

What progress has been made in rapid excavation of tunnels and shafts? Where do we go from here? To get some answers to these questions was the reason that 500 tunnel men-contractors, geologists, professors, lawyers, mining engineers--came to the University of Minnesota May 15-17. The attendance of 500 astonished conference organizer Professor D. H. Yardley, who had anticipated half that number. They came from Japan, South Africa, Austria, Sweden, and Australia to name a few, and an officer of the Corps of Engineers thought all his people should have been there. The Civil and Mining Engineering Departments of the University combined for the program, which was staged by M. K. Cragun for the General Extension Division. The Saga of the Oso Tunnel The present state of the art of rapid excavation is "good." There is little controversy about where we go from here and what's more, this reporter finds that the technical know-how to automate excavation in any kind of ground is extant, even if it will take some years to achieve this state. In a nut- shell though, the present status can be seen in its various ramifications in the saga of the Oso Tunnel, as told by V. L. "Vic" Stevens of Boyles Brothers Drilling Co. :

Jan 7, 1968

L. S. PANYITY.-I made inquiries from the Smith and Dunn people, who are the originators of the compressed air and gas method of increasing the production of oil wells, as to how much pressure the sand will stand; that is, relative to the original rock pressure. They tell me that they have not been able to show, up to date, any pressure in a sand greater than the original pressure. I have also made 'a statement to that effect, but I am really dubious as to whether that is right, as I am not sure that you cannot get a greater pressure. However, I think that a greater pressure would be dangerous because it might cause a loss of gas. C. H. SHAW, ? Lawton, Okla.-In regard to the gas that was put into the pool up in New York State, may it not be possible that, on account of errors, etc., in measuring or computing, there is a mistake in the apparent fact that more gas was gotten out than was put in? L. S. PANYITY.-Unfortunately, I have not the papers I expected from those people to show the actual conditions, but I do not doubt that such

Jan 4, 1919

By John W. Cabot

THE following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the much-vexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a period of about eight days, part of, which time the rail-steel showed great variation in rolling qualities. During the first part of the time in question, it rolled well; later on it began to roll worse until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this .time of transition 'from. good rolling to bad, and back to good again, the course of the manganese was followed' quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no unusual variation Tim steel, in question, was ordinary rail-steel of about "the following composition : C=.35.P=.08.Mn=.98. Si=.08. S=.05. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By John W. Cabot

The following series of analyses, which may, be of interest to Bessemer-steel makers, is submitted as a contribution to the muchvexed discussion of manganese in Bessemer steel. They were made by the writer in the spring of 1881, at the works of the Pittsburgh Bessemer Steel Company Limited, during a' period of about eight days, part of. which time the rail-steel showed great variation in rolling qualities. During the first part of tile time in question, it rolled well; later on it began to roll wome until, finally, it cracked very badly, reaching its worst stage. After this it rapidly improved until it again rolled smoothly. During this time of transition from good rolling to bad, and hack to good again, the course of the manganese was followed quite closely. It is the striking correspondence between these varying manganese contents and the differences in rolling which is here presented as worthy of notice. The other ordinary elements were determined occasionally, but showed no. unusual variation: The steel, in question, was ordinary rail-steel of about the following compusition : C=35. P - .08. Mn - .98. Si = .08. 8 = .06. The samples for manganese determinations were taken at first from an average of two days' work, and later on, when the steel

Jan 1, 1882

By N. M. Saum, W. T. Caneer

Uranium may be in short supply due to the predicted energy needs in the coming years. As a result of this, a new surge of uranium exploration is underway accompanied by the refinement of numerous exploration techniques. One such technique is the monitoring of radon gas in surface soils and rocks as a guide to subsurface uranium deposits. The Colorado School of Mines Research Institute became involved in radon studies in 1967 on a project for the Atomic Energy Commission. Since that time the Institute has conducted numerous radon surveys for a large number of companies which have been active in uranium exploration. The objective of this paper is to relate the techniques utilized by the Research Institute and the results of some of the studies performed. Most of the studies performed by the Research Institute were related to roll front, sandstone-type uranium deposits. However, we have performed radon studies in various other types of rock. For those who may not be familiar with the application of radon "sniffing" in soils and rocks, a brief descriptive background should be given. The following question may be asked-why use radon as a guide to uranium mineralization? Some of the answers to this question are:

Jan 5, 1974

By Robert H. Merrill, Raymond M. Stateham

Recently, the Denver Mining Research Center of the U.S. Bureau of Mines began tests to detect hazardous or potentially hazardous conditions in or around mines with infrared measurement devices. Among the many potential uses of infrared detection techniques are the location of misfires, underground mine fires, combustion in waste dumps, underground water courses and loose rock. However, the primary emphasis has been placed upon the detection of loose rock in roofs, pillars and faces in underground mines. The rock along the edge of an underground opening is subject to two temperature environments: the temperature of the air in the opening, and the temperature of the rock surrounding the opening. Assuming that the rock on the edge of the opening is solid, the rock will reach an equilibrium temperature that depends upon the temperature and flow of the air, the thermal conductivity of the rock and its ambient temperature. Presume that a loose rock exists among this solid rock; because there is a temperature barrier, to some extent, between the loose and the solid, the loose rock will be affected more than the solid rock by the temperature of the air. Therefore, depending upon the temperature differences between the rock and the air, the loose will be warmer or cooler than the solid.

Jan 1, 1970

The banquet Wednesday evening was attended by about 700. The list of speakers was unusually brilliant and each one proved to be so interesting that it was nearly midnight before the dancing began. Capt. Robert W. Hunt was toastmaster. Captain Hunt is about to celebrate his eighty-first birthday but is blest with unusual vigor and it was a great pleasure to all his friends to honor him at this time. His selection is toastmaster was a happy one. The guest of the evening, if among so many stars one could be selected from the rest, was Charles M. Schwab, who said nothing but the urgent telegram from his dear old friend, Captain Hunt, could have drawn him away from his seclusion on his Pennsylvania farm to attend the meeting in Chicago. Mr. Schwab's address was, as usual, scintillating with wit and humor; and while lie did not directly or indirectly allude to the steel strike lie did at the end of his talk discuss serious things and gave it as his opinion that any effort to legislate or control the high cost of living would be futile until this country got down to a basis of an honest day's work for an honest day's wage.

Jan 11, 1919

By D. A. Schemnitz, O. W. Ellis

Certain alloys1 that, as a result of quenching, are retained in the form of homoaeneous solid solution are known to increase in hardness and strength on standing at room temperature or on heating at slightly elevated temperatures. Other alloys2 that, on rapid cooling, are held in the form of homogeneous solid solution, as, for example, certain steels, behave in like manner on heating to somewhat higher temperatures. The observed increase in the hardness and strength of these alloys, referred to as " aging"' or as "secondary hardness," is widely accepted as being occasioned, either in whole or in part, by the precipitation in submicroscopic form of such constituents as were held in supersaturated solid solution as a result of cooling in excess of a certain critical rate. In earlier discussions of the cause of age hardening or secondary hardness, the question of the hardness of the precipitated particles does not appear to have been raised. At present, however, the general opinion appears to be that age hardening and secondary hardness are occasioned by the precipitation of hard particles within the supersaturated solid substance.3 The authors may be wrong in their belief that the last is a prevailing opinion. Nevertheless, it is thought that the following experiments,

Jan 1, 1925

By G. M. Ritcey

Continuous contacting equipment for solvent extraction can be divided into two major areas, according to whether their mode of operation is stagewise or differential (Figure 1). Mixer settlers and the recent Kenics and Sulzer mixers typify the stagewise contactors. In these counter- current contactors, the aqueous and the organic phase are mixed and then separated in a large settling area before the next stage of mixing. Countercurrent differential contact- ors, such as centrifuges and various types of columns, are more compact in that they require less ground area than mixer settlers. [ ] Contactors, in addition to being either stagewise or differential, can be further subdivided into non-agitated and agitated depending on the method used for mixing the phases and producing the countercurrent flow. The simplest contactors such as spray, packed, or perforated plate columns achieve both the mixing and countercurrent flow by means of the gravity difference between the two phases. In agitated contactors such as the Scheibel, Reciprocating Plate, and Sieve-Plate Pulse, mechanical agitation is introduced but gravity differences still produce countercurrent flow. To conserve plant space, and for large throughput with short contact time, centrifugal contactors are used where possible. The reader can refer to reviews on the subject (1-11).

Jan 1, 1978

By Dorsey Lyon

I. INTRODUCTION THE utilization of hydro-electric power in electro-metallurgical indus¬tries, aside from purely mechanical operations, may he of two kinds. The electric energy may be used to supply the heat necessary for the per¬formance of the chemical reactions of a metallurgical process, or the elec¬trolytic action of a direct current may be employed for extraction of metals, either in a reduction process or a refining process. In discussing this subject, it is well to distinguish between established industries, which are producing metals and alloys at a profit by use of the electric current, and the many processes which are either still in the experimental stage or have not even passed the paper stage of development of a patent. That is, we consider electro-metallurgical industries as commercial operations which are now consuming large blocks of electric energy, while processes which are not in commercial operation are only prospective consumers. Also, owing to the difficulty and risk of any attempt to foresee the effect of the European war upon electro-metallurgical industries, we have felt obliged to disregard the war entirely, and state our opinions regardless of its existence.

Jan 8, 1915

By John C. Branner

Inquiries are frequently made concerning the chalk- and clay-beds of Arkansas, usually with a view to the manufacture of Portland cement. The chalk-deposits were first described by Professor R. T. Hill in the annual report of the Geological Survey of Arkansas for 1888, vol. ii., pp. 153-162. Since the publication of that report I have visited localities then unknown, and have accumulated considerable additional information concerning these deposits, dl of which is brought together in the present paper. My report upon the clays of the State has never been published; only a few of the more conveniently available deposits are mentioned in the present paper. The Chalk-Deposits. Stratigraphic Position of the Chalk.—The chalk-deposits of Arkansas belong to rocks of Cretaceous age. The Cretaceous rocks are confined to a single definite area in Southwest Arkansas. Beginning on the Ouachita river, a little northeast of Arkadelphia, its southern or upper margin follows a line about five miles southeast of, and approximately parallel to, the St. Louis, Iron Mountain and Southern Railway from Arkadelphia

Jan 1, 1898

By BION J. ARNOLD

WE can, I think, rightfully claim, irrespective of our faults, that engineers must, in order to last as engineers, possess the qualifications of integrity, stead- fastness of purpose, ability to think straight, and to apply these qualities consistently and continually in their everyday work. All engineers know this, most of them conform, and in order to drive it home I might, if 'clothed with proper authority, preach to you at length, but I shall not take the chance. So I only want to make a suggestion or two to the young engineers. Have an ideal and work toward it. You will have your disappointments and your temptations but keep your record clean, and if anyone says you are foolish or ugly, or homely, or that you need a guardian, take the criticism with a smile, for he may be able to prove his contention; but if he attacks your integrity, strike at once and fight hard, for he has assailed not only your character but your principal asset as an engineer.

Jan 1, 1929