Search Documents

By C. A. Wert, M. G. Coleman

The Zener relaxation in alloys in the a! solid-solution region of the Cu-Ni-Zn ternary system has bear investigated. Of the binary solid solutions that bound this region, Cu-Zn and Ni-Zn exhibit measurable Zener peaks whereas Cu-Ni does not. At constant atomic percent copper, the Peak height drops uni.forinly from the value in the Cu-ZTL binary to zero in CIA-Ali. The cariation of peak ternperatuve with composition is linear. At constant atomic percent zinc, the peak height in the ternary alloys goes through a large maximum as compared with the binary values. The temperature of these peaks varies smoothly with composition. The half-width of the peaks in the ter nary alloys, however, are much larger than those in the binaries. A large enhancement of the relaxation strength of the Zener relaxation in ternary Au-Ag-Zn alloys as compared to the relaxation strengths in Au-Zn and Ag-Zn binary alloys was observed by Firson and ert.' Since this effect was unexpected, the present study was devised to investigate whether enhancement of the Zener relaxation in ternary alloys is a general feature or is particular to the Au-Ag-Zn system. We have chosen the Cu-Ni-Zn alloy system for this investigation. Measurable Zener relaxations are observed in both the Cu-Zn and the Ni-Zn binary systems, but not in the Cu-Ni binary system. A large solid-solution region extends to large concentrations of zinc, making it possible to vary composition of the alloys over a wide range without crossing phase boundaries. EXPERIMENTAL PROCEDURE Two series of alloys were prepared. the first at constant atomic percent copper, the second at constant atomic percent zinc. The compositions of these alloys are shown by the circles in Fig. 1. The alloys were prepared by melting the individual components, each of which had previously been vacuum-melted, in an evacuated quartz capsule in an induction furnace at 1500 C. The capsules containing the molten alloys were quenched in water to reduce coring. Any individual melt which exceeded 0.001 pct weight loss was discarded. The ingots were swaged to a 50 pct reduction of area and annealed for 1 week in an evacuated quartz capsule to aid homogenization. The alloys were then

Jan 1, 1967

By C. M. Haight

The mine blacksmith and drill-steel sharpening shop at the Franklin mine of the New Jersey Zinc Co. is on the surface, adjoining the main shaft. It is a brick building, 51 by 30 ft. inside dimensions, with a corrugated iron roof and concrete floor. .About two-thirds of the steels used are brought up through the main shaft; the remainder through two auxiliary shafts and are carried to the shop by team or truck. At each shaft sufficiently large stocks of sharp drills of various typcs are kept to replace all the dull steels that may be sent up; while at the shop enough sharp drills are kept to replace the dull steels in the stocks kept at the auxiliary shafts. Though this entails keeping a larger number of drill steels in service than might be required by other methods, there is less hurry in the sharpening shop and the steels have a longer period of rest. If a rest from use enables steel to recover from fatigue strains, this method secures that rest. The forms shown in Fig. 1 are supplied to each shift boss in books of 100. These are used to requisition sharp drills from the shaft stocks and cnable the men at the tops of the shafts to sort out the required sizes and to hare them ready to be sent to the various shaft stations. At one of the auxiliary shafts, the dull drills are placed on a platform from which they are dumped into the body of the wagon that takes them to the shop.

Jan 1, 1927

By C. V. Corless

We are living at a period of the world's history in which social phenomena are on so vast a scale, are of so profoundly soul-searching a nature, and are occurring in such rapid succession in the great world drama in which we are both actors and spectators, that, in our efforts to obtain a rational point of view in relation to them, our minds may fail to discern the simple in the complex and our understanding is liable to become confused or even overwhelmed. To the social student whose: scientific training has convinced him of the truth of the evolutionary law, Natura non facit salium, it is neither the vast scale of the events, their deeply soul-stirring nature, nor their rapid succession that matters so much, as the discovery of the underlying principle or law in accordance with which the disintegration and reintegration, which are the two aspects of social evolution, or indeed of evolution everywhere, are occurring. He is most deeply concerned in seeking an answer to the question: Have we in the present great and perplexing upheavals in human society, whether regarded in Central Europe, in Russia, in Great Britain, or in America, a really new cause at work, or, have we, though on a very large scale, merely new manifestations of the working out of an old principle? When we think of the appalling struggle in Europe, into which the world's greatest exemplar of democracy was finally drawn, no one has any hesitation in admitting that the great conflict was fundamentally a life-and-death struggle for self-preservation and self-propagation on the part of autocracy. The variations we meet with in the statement of the cause of the war arise mainly from differing distances of perspective; but in the last analysis all agree that the autocratic system of political gov ernment, which found its very soul and center in Prussian despotism, was consciously arrayed in a final "world-power-or-downf all" struggle against a love of freedom which was steadily widening and deepening throughout the world, and particularly throughout those parts of the world where this love of freedom and justice hasfound expressionin democratic institutions. It is not irrelevant to our discussion to recall in passing that this most imposing structure ever conceived by the human mind as an instrument of tyranny is lying today an irretrievable mass of ruins, completely over-

Jan 1, 1920

By H. F. Easter

(San Francisco Meeting, September, 1915) THE lead department of the El Paso Smelting Works at El Paso, Tex., is operated strictly oil a custom basis. The ores treated are drawn from the surrounding territory, comprising New Mexico, Arizona, western Texas, and northern Mexico. Ores received from the last-named section originally amounted to a very large tonnage, but of recent years have dwindled into comparative insignificance so far as this plant is concerned. This has been clue partly to the establishment of a lead-smelting plant at Chihuahua, which is much closer than El Paso to most of the important mines, and partly to the recent revolutionary troubles in Mexico. There are no mines of either lead or copper in the immediate vicinity of El Paso. In general, it may be said that the lead-ore supply of recent years has been uncertain and precarious, with a general tendency toward an excess of silica and a shortage of iron. This latter requirement has been met in large part by the use in El Paso lead furnaces of considerable amounts of roasted heady copper matte from the Chihuahua smeltery and of converter slag from the El Paso converters. These two materials, coupled with complex lead-copper ores from Bisbee, Ariz., have introduced into the lead-smelting operations a most unusual amount of copper, which has had an important bearing upon the smelting practice of the plant. This matter will be discussed later. The ore, loaded in either box cars or gondolas, enters the storage yard on four tracks elevated about 8 ft. above the ground. As all unloading is clone by hand, unloading platforms at the height of the car floor parallel the tracks on each side to afford a runway for wheelbarrows. At frequent intervals these lengthwise platforms are joined together by others running crosswise to facilitate the distribution of the ores evenly over the beds, which are located below and between the tracks. At present much of the bedding space formerly used for lead ores is given over to the copper department, but 20 bins of various sizes are retained for the use of the lead furnaces and the Huntington & Heberlein roasting plant. The largest of these holds about 1,000 tons, while the smallest holds not over

Jan 8, 1915

By Ernest Klepetko

A notable amount of fossil resin exists in many of the bituminous coal beds of Utah, The upper part of these show a marked concentration of resin, which occurs primarily in the fracture seams. In general, these seams are less than 1/8 in. thick, but it is not uncommon to find coal with areas as thick as 3/8 in. The resin is of the hard kauri variety, with coloration varying from deep blood red to lemon yellow and almost colorless. There is also an almost black variety, which is not readily soluble in the same solvents as the lighter colored resins. These resins are valuable for many industrial purposes. When refined, they are suitable for uses similar to those for which lac resins are usually employed. They are particularly desirable for preparing dielectric varnishes. They are also desirable in preparing printing inks, waterproofing agents, special synthetic rubbers and rubber cements, They are especially suitable as an admixture in synthetic rubbers and cements, as they supply the essential tackiness the synthetics lack. The following chemical trade characteristics' have been found by Inter-Chemical Co. research chemists in the refined resins: Specific gravity (melted)....... I. 03 -1.06 Acid number.................. 6-8 Softening point, mercury method 160°-165°C Iodine valus (Wijs)............ 140-150 Refractive index............... 1.544 Color (Hellige, 25 pct toluol)... 14 Molecular weight, average...... 732 purity, 99 + pct pure hydrocarbon "Unaffected by alkalies and resistant to one hour fusion with solid potassium hydroxide. Completely soluble in aliphatic and aromatic hydrocarbons. Insoluble in alcohols, ethyl acetate and other commonly used alcohols and esters. Compatible with natural and synthetic rubbers, chlorinated and cyclized rubbers, waxes, vegetable oils, mineral oils, rosin, ester gum, phenolic and modified phenolic resins and other natural and synthetic resins of like solvent solubility."* The recovery and refining of these fossil resins has been the subject of much research work and has intrigued many investigators. Broadly speaking, the problem involves separation of the resin from the coal into a very high-grade concentrate, and subsequent treatment of this concentrate to produce an acceptable refined resin for its various usages. Obviously it is also desirable to recover the residua] coal without excessive size degradation. The late W. D. Green, concentration engineer for Combined Metals Reduction CO., obtained U. S. Patent No. 1773997 for the recovery of resin from coal through

Jan 1, 1949

By R. A. Harrington

THE structure of anodic films formed on aluminum and other metals under varied conditions is not well known despite the wide use of such films both as protective coatings and as the dielectric medium in elec-trolytic condensers. The present work was undertaken as a survey of the possibilities of electron diffraction in the investigation of anodic films, especially in comparing the properties of anodic films formed under dif-ferent sets of conditions and subjected to various subsequent treatments. In addition, an effort has been made to compare surface films formed on aluminum by anodic treatment with surface films formed by heating, immersion in chemicals, etc, The electron diffraction method in many cases has been successfully applied to the study of thin surface films. Its principal advantage is that it can be used without removing the films from the base material upon which they have been formed. The low penetrating power of electrons, in the "reflection" diffraction method which has been used in this work, prevents the appearance of diffraction patterns from substances at depths greater than about 100 Angstrom units (10-6 cm.). Different investigations of the structure of anodic films have shown widely varying results, depending on the methods used in preparing the films. Apparently under some conditions these films are crystalline and under other conditions they are amorphous, and it has been difficult to say which type of structure will be found in any particular case. Schmid and Wassermann's' X-ray diffraction patterns of eloxal? films show two broad, diffuse bands, which these investigators attribute to finely divided cubic y-Al2O3-§ Burgers, Claassen, and Zernicke3 obtained sharp X-ray

Jan 1, 1940

By Richard H. Willey

EFFICIENT handling of large tonnages in open-pit mining demands, primarily, an abundance of well fragmented rock. To accomplish this, a drilling and blasting department composed of a well-knit, versatile group of workers and supervisors must be established. Some costs will remain relatively on the same level over a period of years, while others can be greatly lowered as will be shown. The Utah Copper Division, Kennecott Copper Corp., Bingham Canyon, Utah, has been ever alert for improvements in operating methods and equipment to gain increased efficiency and lower costs. BINGHAM CANYON MINE The greatest dimension of the mine is 8000 ft northeast-southwest with a width of 5000 ft southeast-northwest. From the lowest level, at an elevation of 6040 ft above sea-level, the mountain rises in 27 benches on the west side to W level (elevation 7800 ft) and 21 benches on the east side to Q level (elevation 7460 ft). At the inception of open-pit mining in 1906, the overcapping of leached porphyry had to be removed to reach a commercial grade of sulphide ore. The overcapping or waste now remaining is quartzite with intercalated limestone beds. The limestones are usually soft in nature except in the south-middle portion of the mine where they have been metamorphized along the contact zone. This area usually gives drilling and blasting operations a great deal of trouble. Here occurs the greatest amount of secondary blasting, as the well-established fracture planes cause the altered beds to break into large boulders. Several massive quartzite "ribs" occur in the overburden, and as a result, the uniform breakage is difficult to obtain. The major quartzite areas have been subjected to complex folding, fracturing and faulting because of the intrusion of the underlying stock. The monzonite porphyry, which carries the commercial values, presents no serious drilling problem because of its softness and extensive minute fracturing throughout the mass. A series of major slips or faults pass through the ore body which, although of considerable advantage to the drilling and blasting department, sometimes works to the disadvantage of the track department. Drilling and blasting of the porphyry apparently becomes easier as depth is attained, but highly siliceous streaks throughout the pit still present difficulties. At no place is the rock of such character as to allow excavation without preparations. On certain higher elevations or levels, old fill material can be dug by the shovels, but only at some risk to equipment because of bank slippage. PAST METHODS At the outset of shovel operations in 1906, drilling was done with the Ingersoll-Rand F-24 piston drill mounted on an un-

Jan 1, 1947

By Grover J. Holt

A DETAILED description of the many variations in iron mining and transportation practice in Minnesota would require much space. Since a fairly detailed description of the practices then in use was published in the guidebook issued in connection with the meeting of the Institute on the iron ranges in 1920, and subsequent developments have been described by E. E Hunner,1 M. H Barber,2 and A. E. Anderson, J. M. Riddell and G. J. Holt,3 it will not be necessary here to do more than review the highlights of current practice Details on any points of interest can be obtained through correspondence with the operators involved.† The iron ores of Minnesota, which have been formed through enrichment, of the iron formation in which they occur, largely by the removal of silica, are usually covered by a blanket of glacial drift known locally as "surface." Surface material, including sand, clay, hardpan and boulders, makes up the greater portion of the stripping in open-pit operations. In some instances, stripping also includes taconite and "paint rock," directly below the surface material and overlying the ore. Taconite is the iron formation, a ferruginous chert with interbedded slate layers. "Paint rock" is a local term for oxidized slate layers interbedded in the iron formation, high iii phosphorus, alumina and moisture The iron ores fall into two classes- (I) direct shipping (merchantable ores or ores requiring no treatment except possibly crushing or screening to make an acceptable sized product), and (2) ores requiring beneficiation (such as sintering, drying, washing, jigging, high-density treatment, or magnetic separation in the case of magnetite) The Mesabi Range produces chiefly soft Bessemer and non-Bessemer ores. The Cuyuna Range produces mainly low-manganese brown ore and high+manganese black ores, with some iron ore. The Vermilion Range yields mainly Bessemer and non-Bessemer iron ore, with some hard or lump ore that finds use in the open hearth. Open-pit mining is limited to the Mesabi and Cuyuna Ranges but underground mining is done on all three. The choice of mining methods is determined by the relative economics of overburden-removal and shaft-mining costs. STRIPPING PRACTICE Common practice has been to remove the bulk of the overburden during the winter season and to mine during the summer. In the present emergency many operators are forced to forego the economies attained by year-round utilization of equipment and to equip for, and carry on, stripping and mining simultaneously. In the normal years or lean years to come, most properties probably will be overequipped and high depreciation charges will have to be absorbed

Jan 1, 1942

By C. G. Brennecke, R. T. Gallagher

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in , mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. Purpose Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls of roof, coal, or ore. Table Il,2 is a compilation of statistics as published by the United States Bureau of Mines, showing the percentages of fatal accidents caused

Jan 1, 1947

By R. T. Gallagher, C. G. Brennecke

This paper is the result of a research program entered into cooperatively by the General Reinsurance Corporation and Lehigh University in January 1944. The research program was instituted to find a more positive method to determine the presence of hazardous roof conditions in , mining operations. The co-authors, together with Mr. R. D. Currie, Engineer for the General Reinsurance Corporation, started working on the project in January 1944, first undertaking a library search; second, a preliminary study based on some existing equipment; third, the design of new and more suitable equipment; and finally, the field testing of equipment and methods. Purpose Any study of the accident statistics of mining operations will disclose the rather startling fact that approximately 50 to 60 per cent of all fatal underground accidents in the anthracite and bituminous mines are caused by falls of roof and coal, the metal and nonmetal mines showing only a slightly smaller percentage. Advancements in safety engineering have produced definite results in the decrease of accidents due to blasting, haulage, electricity, and explosions but no such decrease is shown in those caused by falls of roof, coal, or ore. Table Il,2 is a compilation of statistics as published by the United States Bureau of Mines, showing the percentages of fatal accidents caused

Jan 1, 1947

By Henry S. Munroe

THE earliest accounts we have of Japan represent the country as having great mineral wealth, especially of precious and useful metals. Marco Polo, the Venetian traveller, in the thirteenth century, writes of "Zipangu:” "They have gold in greatest abundance, its sources being inexhaustible. The king does not allow of its being exported. To this circumstance we are to attribute the extraordinary richness of the sovereign's palace. The entire roof is covered with a plating of gold. . . . The ceilings of the halls are of the same precious metal ; many of the apartments have tables of pure gold of considerable thickness, and the windows also have golden ornaments." Marco Polo also gives an account of an unsuccessful Tartar expedition against Japan, prompted by the supposed great wealth of the country. Columbus also, as well as many other explorers, were attracted and encouraged by these prevalent reports of the wealth of the islands of Zipangu. Kaempfer, writing in 1727, speaks of the great mineral wealth of Japan, and especially of the abundance of gold, which, he says, is found in many provinces. The Portuguese and Dutch, while they had trading-posts in Japan, furnished tangible evidence of the truth of the early reports. Between 1550 and 1639 the Portuguese merchants sent home from Japan nearly three hundred million dollars' worth of bullion, most of which was gold. As the relative value of equal weights of gold and silver was then six to one, while in Europe, at the same time, it was nearly twelve to one, the exchange of silver bullion for gold was by no means an unimportant part of their business. After the Portuguese, the Dutch continued the exportation of bullion, and the exchange of silver for gold, though with less profit, as the relative value of gold increased with the demand. Between 1649 and 1671 the Dutch traders sent home over two hundred million dollars in bullion, of which, however, nearly two-thirds was silver. In 1671 the Japanese government, alarmed at the rapid rate at which the precious metals were leaving the country, issued an edict forbidding the exportation of gold or silver, under heavy penalties, which had the immediate effect of stopping this trade. Besides bullion, copper formed at this time a most important article of export. According to Dr. Geerts,* who has examined the old * Transactions Asiatic Society of Japan, vol. iii, p. 41.

Jan 1, 1877

By N. J. Grant, C. C. Wang

The Ti-Cr-O ternary system has been studied in detail near the titanium-rich corner within the limits of 10 wt pct 0, and 20 wt pct Cr. Studies were extended, but not in detail, to the region beyond 25 wt pct 0, (50 atomic pct) and 62 wt pct Cr (60 atomic pct). Four isothermal sections at 1400°, 1200°, 1000°, and 800°C are presented as well as two vertical sections at 1 and 2 wt pct 02. DURING the last decade much interest has been shown in the development of high strength titanium alloys for high temperature and corrosion resistant applications. Extensive research is being carried out at present, as the current literature indicates, in order to study the properties of titanium and to develop improved alloys. Two of the important alloying elements in commercial titanium alloys are chromium and oxygen and it would be desirable to know their combined influence upon titanium. For this purpose the present work was carried out to investigate the titanium-rich corner of the ternary system TiICr-0. The binary systems Ti-Cr and Ti-0 have been published recently. The Ti-Cr system was studied by several investigators " and their results are in close agreement. The eutectoid decomposition of the B phase has been shown to be extremely sluggish. TiCr, was the only intermetallic compound found in this binary system and was formed at 1350°C by a transformation from the p phase. TiCr? was established as the cubic C 15 (MgCu,) type of structure with 24 atoms per unit cell and was designated as the y phase. This terminology will be adopted in the present work. There was disagreement about the actual composition of this compound among the several investigators, although it is evident from their data that the compound probably has a solubility range of about 2 to 3 pct and is in the vicinity of 65 pct Cr. It has been indicated recently that a high temperature modification of this y phase (TiCr,) existed at a temperature above 1300°C." ' This high temperature modification was identified as a hexagonal C 14 (MgZn,) type of structure with 12 atoms per unit cell. The exact transformation temperature from the high temperature phase to the low temperature phase has not been established. A considerable hysteresis was observed and, due to the sluggishness of this transformation, the high temperature phase often co-existed with the low temperature phase at temperatures below 1300°C. A preliminary study of several Ti-0 compounds and the Ti-0 system had been carried out by Ehr-1ich."-"' The most complete binary Ti-0 system was the one reported recently by Bumps, Kessler, and Hansen." The first intermediate phase found in the system was the 8 phase which formed by a peritec-toid reaction of the phases a and Ti0 at temperatures below 925 °C. This reaction is extremely sluggish. The structure of this 8 phase was tentatively identified by these authors as being tetragonal and the lattice constants were found as c,, - 6.645A, a,, = 5.333A and c/a = 1.246A. Experimental Procedure The raw materials used for this investigation were TiO,, electrolytic chromium, iodide titanium, and sponge titanium. The TiO, was in the form of powder of chemically pure grade (99.8 pct pure). The chemical analysis of the electrolytic chromium was: 0, 0.50 pct; Fe, 0.07; Cu, N, and C, 0.01; and Pb, 0.001. The oxygen in the chromium was calculated as part of the final oxygen content of the alloys. The alloys were prepared by the cold crucible method using a tungsten arc. The entire system was evacuated and flushed with purified helium three times and then filled with helium. Each alloy was melted, turned over, and remelted at least four times to insure homogeneity. The total melting time was generally from 6 to 10 min. A master alloy of 25 pct 0,-75 pct Ti was prepared to facilitate alloying by melting compacts of TiOl powder with either iodide or sponge titanium, yielding the compound TiO. It was found necessary to bake the TiO, powder compact at about 150°C to remove adsorbed moisture. This was done to prevent the disintegration and spattering of the compact when the arc was struck. TiO, powder dissolved quite readily into the melt and no other trouble was encountered.

Jan 1, 1955

By C. J. P. Ball

Prior to 1939 the bulk of the magnesium metal produced outside of the united Stater was extracted directly from the ore and ifi the United States from magnesium chloride obtained as a by-product from the treatment of natural brines. A typical brine is one containing about 0.25 to 0.75 per cent bromine, 11 to 14 per cent sodium chloride, 9 to 11 per cent calcium chloride and 3 to 10 per cent magnesium chloride. The state of Nevada was known to possess large deposits of magnesite ore (MgCOs, the carbonate of magnesium), in Gabbs Valley, near Luning, approximately 350 miles north of Boulder Dam. Deposits mined in Europe were supplying magnesite giving 97 per cent MgCOs with about I per cent each of silica, lime and oxides of iron and aluminum. parts of the Luning de-posits Were almost equally rich, and the general average was of sufficiently high grade for production of magnesium. power to the amount of 200,000 kw. was available immediately from Boulder Dam, and water from Lake Mead, and it was this combination of available power, water, and ore that led to the initial proposal to erect a magnesium reduction plant in southern Nevada to reduce the magnesite ores from Gabbs. The extraction of magnesium metal from these magnesite deposits had been considered by the I. G. Farbenindustrie of Germany as far back as 1929. Mine and Oxide Plant The mine and oxide plant of Basic Magnesium Incorporated are perched upon the oride slope of the Paradise Range, at an altitude of 5000 ft., overlooking the 30 mile desert panorama of Gabbs Valley, Nevada. , Ore Occurrence The Gabbs magnesite ores occur in a thick series of flat, westerly dipping dolomites of Upper Triassic age. The mag-"esite bodies are exposed in steep canyon "areas encircling the north and east edges of a northerly projecting tongue of a roughly elliptical stock of granodiorite, which intrudes the dolomite. The magnesite mineralization is considered to be a a of calcium by magnesium through the agency of hydro-thermal solutions associated with the intrusion of the granodiorite. The ore bodies are of very irregular shape and distribution. Incomplete evidence points to deep pipelike replacement shapes that mushroom out erratically at various elevations. A wide latitude in the degree of magnesium replacement is reflected in a variance of quality from pure magnesite to magnesitic dolomite. The, ore is a massive crystalline mag-nesite. Though some differences in characteristics occur between ore bodies, in general the ore is a medium-grained carbonate varying in color from white, through all shades of gray, to black. Recrystallized dolomite, which encloses and occurs as

Jan 1, 1944

By Willis T. Burns

I. Introduction.......................................... 703 II. History................................................ 703 III. General Description of Plant......................... 704 IV. AnoDes................................................. 711 V. Cathodes............................................... 714 VI. Electrolyte............................................ 718 VII. Electrolytic Slime..................................... 727 VIII. Power................................................. 728 IX. Operating Details..................................... 732 X. Furnace Refining...................................... 736 XI. Physical Testing oF Products.......................... 739 I. Introduction. These notes are submitted, not as a discussion of the modern practice of electrolytic-copper refining, but as the record of a refinery that was among the pioneers in the field and that is to-day, and has been for 17 years, operating under conditions not to be found in any similar plant in the country. I refer to the current density, which is at least 60 per cent. higher than that regularly employed elsewhere, and to the fact that the anodes treated are the direct product of the converter rather than of the reverberatory furnace. The writer has no knowledge of any other refinery treating anodes of this character. II. History. This refinery, now one of the oldest plants of its kind operating in this country, was built in 1892 by the Boston & Montana Consolidated Copper & Silver Mining CO. to refine the product of its Great Falls reduction works. The estimated capacity of the plant as designed was 65,000 lb. of cathodes per day at a current density of 16 amperes per square foot.

Jan 1, 1914

By Edward P. Chapman

IN the Leadville district toward the close of the "intermediate mesothermal period" of mineralization, there occurred a stage of ore deposition marked by a rather complex mineral association. As bismuth minerals formed in many places during this period, it is here called the "bismuth stage" for convenience of description. The minerals so far identified with this stage, listed roughly in the order of prominence, are: chalcopyrite; several varieties of galena, differing slightly from one another in their small contents of silver, bismuth and tellurium; altaite; hessite; galenobismutite; alaskaite; aikinite; ,gold; tennantite; argentite; and perhaps sphalerite and arsenopyrite. With the exception of gold, the age relations of these minerals are difficult to determine. As shown in their descriptions, they all appear contemporaneous and hypogene. Gold may be in part contemporaneous, but most of it is distinctly later. Where minerals of this stage occur so that they can be mined alone, as at the Tucson mine, they constitute high-grade ore. Elsewhere their presence in small amounts has served to increase greatly the value of what otherwise would be low- grade pyritic or zinc-lead sulphide ore. The distribution of the bismuth ores corresponds closely to the distribution of gold ores, though not so general. It seems probable that most of the gold in the district was deposited during the "bismuth stage." These ores occur relatively near the supposed centers of mineralization in Breece and Printer Boy Hills or deep down along the Tucson-Maid fault, which is one of the well recognized channels of mineralization in the Iron Hill and Graham Park areas. Consideration of the high-grade nature of this mineralization and the fact that it appears to be found relatively close to the source of mineralization suggests that prospecting along some of the known channels, even deeper than they have yet been prospected, may offer hope of commercial success.

Jan 1, 1939

By E. C. Bitzer

The primary object of the work described in the following pages was to simplify the equipment in the separating circuit of the heavy-media process by substituting a spiral classifier for the separatory cone. Mechanical considerations were the leading attraction and the best that was hoped for on metallurgical performance was that the new vessel would give results equal to those obtained by conventional equipment. Tests have demonstrated in commercial operation on iron ore that the mechanical advantages of the spiral separator are about as predicted; also, the metallurgical performance is superior to the cone on the ores treated. Treatment of iron ore involves the separation of two products: a concentrate that sinks and a float product that contains true float material plus a controlled division of interfering middling. The middling material is heavier than the average specific gravity of the separating medium. Recent work with the spiral separator on Tri-State zinc ore showed that the middling material had to be recovered as concentrate because this fraction contained the bulk of the zinc in the ore. It has been demonstrated that it is possible to make three products with the new separator on an ore such as this: a float tailing, a float middling, and a high- grade heavy sink product. It appears from this last work that the new separator has definite mechanical and metalluigical advantages over any type of separating cone for treating feed that contains large amounts of material of a specific gravity close to that of the separating medium. However, either type of separator should perform equally well, metallurgically, on feed that is free of middlings. Each series of experiments with the spiral separator has required additional work to fully develop the possibilities of the machine. For this reason the paper is divided into chronological parts. History of Development A drag-type classifier was first proposed as a substitute for the cone separator by Butler Brothers technicians during the initial tests with galena medium at Crosby, Minn., in 1937. The desire for finding a substitute for the cone arose from trouble with interfering middlings and certain operating disadvantages of the cone. The possibility of using a spiral classifier was also suggested at this time by Emmett Butler and C. J. Abrams. However, inability to satisfactorily recover fine galena, which was used as a medium, terminated all development work at Crosby. During the winter of 1937--1938 investigation started on magnetic medium with concurrent development of the inverted or closed-top cone, which was found necessary to eliminate iron-ore middlings with the float product. About

Jan 1, 1949

By G. W. Healy, D. C. Hilty

MAJOR considerations in the production of stainless steel are the utilization of stainless steel scrap and the recovery of chromium and other metallic values from the initial furnace charge. The decarburization of a bath of molten chromium steel with gaseous oxygen is usually accompanied by a considerable amount of metallic oxidation. Since recovery of this metal from the slag may require substantial expenditures of time and materials for slag reduction, holding metallic oxidation to the minimum consistent with good operating practice is generally desirable. The important role of temperature in minimizing metallic oxidation is illustrated by Fig. 1, taken from the results of Hilty, Healy, and Crafts,' who established the quantitative relations connecting the amounts of chromium, manganese, and iron oxidized during the oxidizing period of chromium steel heats with the composition of the initial charge and the temperature and composition of the molten bath after oxidation. Higher temperatures after the oxygen blow result in lower metallic oxidation. Although high temperatures are desirable for minimizing metallic oxidation, practical operating considerations limit the degree to which they can be employed. Excessively high temperatures or prolonged operation at moderately high temperatures may cause serious damage to the furnace refractories, so that a compromise must be effected. The problem, therefore, is one of controlling the oxidizing period of chromium steel heats to the shortest time at the highest practical temperature. The most effective tool the steel melter has for attaining high temperature while decarburizing a chromium steel heat is now commonly considered to be the oxygen lance with an adequate supply of gaseous oxygen. In order for the tool to be effective, however, the heat resulting from the oxidation of carbon, chromium, silicon, manganese, and iron in the bath must exceed the heat losses from the furnace. General recognition, of this principle has stimulated a trend toward faster injection of oxygen. For example, Pachaly2 proposed a high temperature at the start of the oxygen blow or a high rate of oxygen input as a means of obtaining the desired carbon level with high chromium recovery. On the other hand, limited understanding of the specific effects of oxygen input rate has hampered development of optimum practices. As part of a broad study of the metallurgy of chromium steel melting, therefore, the Linde Air Products Co. and the Electro Metallurgical Co. at their Metals Research Labo-ratories have evaluated the heat-balance during the oxidizing period in terms of oxygen input rate. The evaluation has then been related to factors such as temperature increase, metallic oxidation, oxygen Utilization, etc., and extrapolated to include a wide

Jan 1, 1958

By M. I. Sherman, J. D. H. Strickland

PRELIMINARY experiments in these laboratories showed that whereas pyrite1 produced only sul-fate the action of aqueous chlorine solutions on most other sulfide ores resulted in the formation of a mixture of sulfate and elemental sulfur, the production of the latter being favored by a very dilute solution of oxidant. The reactions taking place were obviously complex and only a detailed kinetic study could be expected to clarify the position and enable a prediction to be made of conditions leading to the rapid formation of metal salt and the economically desirable elemental form of sulfur. Galena was chosen for the first investigation as it is of widespread occurrence and is representative of a simple cubic lattice sulfide containing the monosulfide unit, S2-. Experimental Procedure The apparatus and general technique used in this work have already been described.' Analyses for chlorine and sulfate were carried out by the same methods as those used for pyrite. The lead in 1 ml aliquots of solution was determined polarographi-cally, after destroying chlorine with hydrazine hy-drochloride and making solutions 0.5 molar with hydrochloric acid. A large sample of Kansas galena, assaying at better than 98 pet PbS, was crushed and wet sieved to give fractions of —10 + 14, —20 + 28, —28 + 35, and —48 + 65 Tyler screen. The particles were almost perfect cubes and the apparent surface Per gram was calculated assuming each particle a cube Of side equal to the mean mesh opening. A volume shape factor, calculated as for pyrite, was exactly unity. The main apparatus was unsuitable for direct visual examination of the ore particles during the reaction. For this purpose a small cell from a Spekker Absorptiometer optical flats 1 cm apart) was l by a greased microscope slide after filling with oxidant solution. One or two ore particles were placed in the cell and the solution was stirred by a glass covered speck of iron wire activated by an external rotating magnet. The surface of an ore particle was examined under a binocular microscope at between 10 and 40 magnifications. Results Experiments were made under a wide variety of conditions, the form of presentation of the data being illustrated by Fig. 1, where the concentrations of chlorine, sulfate, and sulfur are plotted against time. The fictitious concentration of solid sulfur is used for convenience and is the molarity of sulfur which would be recorded if the elementary sulfur formed during the reaction were dissolved in the liquid iii the reaction vessel. As some lead sulfate is occluded with the sulfur on the ore particles the amounts of sulfur and sulfate formed during a reaction cannot be calculated

Jan 1, 1958

By W. O. Philbrook, A. H. Jolly, T. R. Henry

In the course of a study of slag-control methods, the authors devised a laboratory technique by which the basicity of basic open-hearth furnace slags could be estimated with sufficient accuracy to make the method of possible interest for slag-control purposes. The process consisted of measuring the slight basicity of an extract of the powdered slag in water. The procedure was presented, for the benefit of those who might care to experiment with it, in a paper submitted in the 1944 McKune Award Contest and presented at the 1944 Open-hearth Conference in Pittsburgh.' Interest expressed at that meeting and favorable operating experience with the method at a neighboring plant, as described in a related paper by Michael Tenenbaum and C. C. Brown,; have encouraged us to present further details of the development, technique, and pitfalls of the method and some additional data not included in our first report. At the outset it must be admitted that this method of estimation of slag basicity is not perfect; neither is any other that we know of. It is subject to somewhat greater errors than would be desirable, but compares favorably with other techniques in this respect. It has the disadvantage that it places the final determination of slag basicity in the hands of a laboratory technician rather than the furnace oper- ator, although it can be operated in a control laboratory adjacent to the furnaces. It requires close attention to certain details, as do most laboratory procedures. On the favorable side, it eliminates the "human factor" of personal judgment inherent in estimation from pancakes or powdered samples. The procedure can be placed in practice much more rapidly and presents much less of a training problem than visual methods of estimation. The principle and operation of the method are so simple that it would not be surprising if others have experimented with the same or similar procedures, but we are not aware of any prior publication of details. Our own shop has been operating fairly successfully for several years with the aid of slag pancakes. Since the past year or two have not been favorable for the expenditure of time and energy where the need was not urgent, we have not introduced the new practice for actual slag control and hence do not have extensive operating data. In presenting this method, therefore, we make no claims as to theoretical justification nor guarantees as to practical applicability, but offer it as an empirical observation. We believe it has sufficient merit to warrant its investigation by those just instituting a slag-control program or in search of supplementary methods for judging slag basicity Principle of the Method It is well known that when burnt lime or slaked lime is shaken up with water it

Jan 1, 1945

By J. J. Van Nouhuys

THE economics of aerial survey and the technical processes by the aid of which vertical and oblique aerial photographs are turned into line maps showing the most profuse topographical detail such as contours, rivers, roads, plantations, habitations and cultivated lands do not concern us here. They have been ably and exhaustively described in the publi-cations of the British War Office, handbooks on surveying methods and on photogrammetry and in the South African mining, engineering and geological press. Suffice it to mention that for geological interpretation vertical photo-graphs are used on such scales as soon to 1/5,000 to 1/10,000, overlapping each other by 55 to 60 per cent in the direction of flight and some 10 to 20 per cent sideways on to the next sequence or strip. Through this duplication in the overlap the stereoscopic examination becomes possible. The standards by which monochrome aerial photographs are inter-preted can be grouped under the following headings: 1. Continuity.-The continuity of topographic relief not obtainable on the ground owing to the smallness of man relative to that relief. Here lies the greatest value of aerial survey with relation to geology. An immediate alignment can often be made of drainages running in different directions on each side of a hill; saddles and gorges in the mountainsides; abrupt termination of outcrop or indubitable signs of faulting. Most conclusive evidence is thus often obtained about faults which may be perfectly visible at one place on the ground but cannot elsewhere be identified because of decreased throw. Similarly, dikes can often be followed notwithstanding frequent interruption and disappearance under the soil. Scattered outcrop in scrub-covered or bush-covered country can be conveniently located and often correlated, with a large saving of time compared with field work. The same applies to geological contacts. Once these have been established at a few points on the ground, the intervening stretches can be drawn in.

Jan 1, 1937