Search Documents

By H. D. Wilde

At the Sugarland and Raccoon Bend fields in the Gulf Coast area, all wells are drilled with rotary tools and the casing is always set in cement that is placed by the circulation method. After the cement is set, the rotary mud that fills the hole is not withdrawn or bailed out; consequently, it is not customary to give the cementing job a direct test either by putting pressure on the hole to see whether the cement will hold or by observing whether an effective water shut-off is secured. About three years ago, this company started the practice of coring the cement left in the bottom of the casing and examining the core thus secured. If the core was hard and strong, the cementing job was judged a success but if the core was incoherent, soft, and crumbly, the job was considered a failure. Of course, there were intermediate types of cores and it was not always a simple matter from this examination to decide whether the job was a success or failure. After about two years, a summary of the core examinations that had been made indicated that of cementing jobs made at depths of 1000 ft. or less, 60 per cent.. were failures; of those between 1000 and 2000 ft., 80 per cent. were failures, and of those between 3000 to 6200 ft., 100 per cent. were failures. This sta,rtling table emphasized the need of the study of the conditions under which the wells were cemented and of adopting means to reduce the percentage of failures. In addition to these core tests, two wells gave direct evidence that the cementing jobs were not always successful. In one, a four-year-old well at Goose Creek, the casing was perforated, and when fluid was circulated some of the old cement wss brought to the surface. Most of it was powdery and the few chunks that were brought up were soft and crumbly. The other was a well at Raccoon Bend which during a blow-out brought a number of chalky, soft and crumbly pieces of cement to the surface. Suggested Explanations of Cementing Failures Efforts were made at once to explain the causes of these cementing failures. As all of the cements used were of a high grade and gave

Jan 1, 1930

By B. F. Buie

Included in the general category of clays is a large and varied assemblage of nonmetallic silicate minerals which characteristically occur as fine-grained particles having flaky, sheetlike, or rod-shaped form. Most, though not all, are hydrous aluminum silicates. Amount and kind of impurities vary greatly, and these strongly influence the uses of the various clay types. Clays occur in a wide range of geological situations: as bedded sedimentary deposits composed of the weathering products of feldspar and other minerals; as alteration products of igneous, sedimentary, and metamorphic rocks weathered or hydrothermally altered in place; and, to a more limited extent, as hydrothermally introduced materials. TYPES AND MARKETS On the basis of chemical composition and crystal structure, two major groups of clay minerals recognized are the "kandites" or kaolin group, and the "smectites" or montmorillonite group. Another major type is illite, particularly important as a constituent of shales. Two additional mineral species having economic importance are attapulgite (palygorskite) and sepiolite. For present purposes, however, a classification based on utilization is more appropriate. The U.S. Bureau of Mines recognizes six types of clay: kaolin, ball clay, fire clay, bentonite, fuller's earth, and miscellaneous clay. Kaolin The kaolin group of minerals consists of the mineral species kaolinite, halloysite (metahalloysite), dickite, and nacrite, although the latter two are not being produced commercially. Kaolin, also called china clay, is a high-purity white material. Perhaps it is best known as a principal ingredient in the manufacture of chinaware, porcelain, and other high-quality ceramic products. However, by the mid-1970s very close to 50% of the kaolin produced in the United States was going to the paper industry for use as a filler and coating material. Manufacture of refractories uses about 12% of U.S. production. Kaolin is also used in plastics, in the rubber industry as a filler in footwear, electrical cable, and similar products, and as a conditioner of rubber for automobile tires to add strength and abrasion resistance. Smaller amounts are used in printing ink, paint, and adhesives; as insecticide carriers; in the production of catalysts for the petroleum refining industry; and in many other industrial and commercial applications. Production and use of kaolin in the United States doubled in the ten years from 1946 to 1956, and doubled again by 1966. Growth continues at a rate of about 7 % per annum.

Jan 1, 1976

FOLLOWING the presentation of the papers by Messrs. Mahan and Butler, the discussion printed below ensued. A. C. LANE* With particular reference to the New England con-sumer, I entirely agree with Mr. Mahan that intelli-gent marketing methods will do a good deal, but there is more than one way of improving them. For instance, coal can be shipped best to New England about this time of year-after the storms of the winter and before the movement of crops in the summer. For that reason there ought to be seasonal freight rates. This will be agreed to by most coal men if you will ask them, especially those who are connected with large concerns like the Metropolitan Coal Co., and yet they do not get seasonal freight rates partly because the railroads are afraid if they once reduce them they will never have a chance to get them back again. But it would be an improvement to have seasonal freight rates. Another thing: When we are buying in New England we want really a certain amount of heat value in our coal. There is no great advantage in our buying ash, nor is there any particular advantage in the railroad shipping ash and clogging the circulatory system of the body politic any more than clogging the circulatory system of the physical body. It would be desirable if the wholesaler, and to some extent the retailer, could guarantee the amount of ash or sell their coal on heating value. If you are interested in that you will find some interesting charts, in "Anthracite Coal Costs Analyzed," a pamphlet issued by the Anthracite Coal Consumers Association, Inc., New York City, as to rates from various and sundry points for bituminous and anthra-cite coal from the field to New York, Buffalo and Chi-cago. Here in New England they are both up against the competition of oil. About 3 or 3 1/2 bbl. oil will do the work of a ton of coal. One of my millionaire friends who is well posted on the situation is putting oil in his Commonwealth Avenue house because it is the most economical. Moreover, we can get Welsh coal from across the water (and help equalize this matter of exchange with Europe) in close competition with Penn-sylvania coal.

Jan 4, 1928

By C. F. Willis

Many of the failures in vocational education are due to the fact that the educational methods were not designed to the capabilities, habits, and environments of those to be trained; rather they were based on the policy that education is education and lessons are lessons, whether for youngsters of fifteen or for men of forty. Vocational education among miners involves, first, a study of the men themselves, their habits, and the use of their leisure time; second, a study of the differences between the methods of teaching required for men and for children. Certain fundamental requirements of training methods for miners are reasonably universal and may be applied with success to any ordinary mining community. The rate of labor turnover is another consideration; it would be useless to design a four-year course for men who remain in one place only a few months. Length of Course The first consideration should be the length of the course. Few mining communities have a sufficiently stable population to make it possible successfully to carry on a course for over a year. While some men might complete a four-year course, the number is comparatively small compared with the number to whom a shorter course would be of service, and it is better to raise the standards of education even a little for a large number than to raise them to a high level for a few. It is perfectly possible to attain both objectives by arranging the courses in small units; all the units, when grouped together, should comprise a fairly complete course, yet any one unit should be complete in itself and of benefit to the workman. It should not take many of these units to make a miner or a timberman out of a mucker; but to do this the course should be short, because muckers seldom stay in one place long. By grouping a number of these units together it Would be possible for a miner to become a shift boss or a shift boss a foreman, and so on. As far as possible the units of the course should not be dependent on those preceding or following. The workman understands the completed job but he is not accustomed to carrying on several jobs at the same time and

Jan 1, 1920

By Ralph E. Grim

THE technology of clay minerals is defined, for the purpose of this review, as- the application of fundamental data regarding clay minerals, and techniques of handling them, to the various industries, arts, and professions concerned with clay materials. The aim of the paper is to narrate recent developments in clay mineral technology. This review does not claim to be complete, and perhaps gives undue emphasis to matters that have been worked on in the author's laboratory or with which he has some other connection. In the United States in recent years, particularly since the end of World War 11, interest in clay mineralogy has increased greatly. Many laboratories in many different fields have embarked on studies of clay minerals but unfortunately much of this work has not been published. CERAMICS In the field of ceramics, in recent years, a great deal of interest has developed in clay mineralogy. Papers too numerous to be reviewed here have been published portraying the clay mineral composition of substantially all the important types of ceramic clays in all countries. There has been a growing tendency to attempt to solve processing problems on the basis of clay mineral data rather than chemical analytical data. Likewise, there is an in- creasing tendency to control the characteristics of raw materials on the basis of clay mineral composition rather than chemical composition. In the United States in the last few years something like 50 differential thermal analyzers have been set up, and many are for the sole purpose of controlling raw material and processing. The ceramic industry is currently increasing its attention to the influence of exchangeable ions and soluble salts on physical properties. Ion concentration in clay suspensions has long been a matter of interest, but now it is also of interest in clays in the plastic state because of its recognized importance in the plastic, shrinkage, and bonding properties of clays. Students of clay have long recognized that an understanding of the plastic properties of clays is based on an understanding of the character of the water in clay-water systems, the nature of the binding force between individual clay mineral particles, and the factors that control the character of the water and the nature of the bonding force. In the last few years, some extremely important contributions have greatly increased the understanding of the nature of water adsorbed on the clay mineral surfaces. In this connection the work

Jan 1, 1952

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By Lawrence K. Jetter, Robert F. Mehl

Some advances have been made recently in the theory of the kinetics of precipitation from metallic solid solution despite the complexities of the problem, but there is surprisingly little quantitative information available on rates of precipitation with which to test present theory or upon which to build new theory. Attempts to measure rates of precipitation have been beset with difficulties which originate both in the anomalies that attend the changes in the properties selectcd for measurement, as, for example, in electrical conductivity or mechanical properties, and also in the complexities in the structural changes in some systems, as in the aluminum-copper system. If the functional relationship between the quantity of precipitate and the value of the selected property is uncertain, measurements of that property are obviously of uncertain utility in determining absolute rates of precipitation. If the precipitating system passes through one or more transition stages, the interpretation of measured rates lacks definiteness; in such cases, it is necessary to measure the rate of reaction in each separate stage, if the rate measurements are to have any significance from the kinetic point of view.* These difficulties cannot be wholly avoided, for at least in some measure they are characteristic of the process of precipitation from solid solution, but they can be minimized both by the selection of a simple system and by the use of a method of measurement relatively free from anomalous behavior. The present paper reports dilatome tric measurements on the rate of precipitation of silicon from the aluminum-rich solid solution in the aluminum-silicon system—a study that approaches the desiderata of simplicity. The aluminum-silicon system offers advantages from these points of view: there are no known anomalies in the property changes accompanying precipitation; there are no known transition stages; the precipitate is an element, not a compound, and both matrix and precipitate are cubic, and while the structures are not identical (the solid solution is face-centered cubic and the precipitate is diamond cubic), the system at least approaches the ideal case of a crystal precipitating from a matrix of the same crystal type—the ideal case which Becker6 assumed in treating the precipitation process theoretically. The dilatometric method, while not free from disturbing effects, as the subsequent dis-

Jan 1, 1943

By W. L. Freyberger, R. B. Booth

Froth flotation is a chemically induced method for beneficiating or up- grading an ore, which utilizes a layer or column of froth as a separating medium to segregate and remove the valuable minerals from the worthless gangue components of a finely ground ore suspended in water. The object of this chapter is to discuss the theoretical aspects of froth formation, the various frothing agents employed in flotation, and the effect of chemical structure on froth formation, and to correlate these factors with flotation technology. The flotation method of separation is conducted in three main steps: 1) selective chemical modification of the surface of specific mineral particles to effect floatability or nonfloatability; 2) contact between air bubbles and mineral particles, the selective adherence of floatable minerals to these bubbles, and the rejection of nonfloatable minerals; and 3) separation of the floatable minerals from the nonfloatable minerals. As indicated above, these three operations are achieved by the use of chemicals. Frothers play their most important role in the second and third steps by influencing particle- bubble contact and by affecting the degree of separation obtained in the froth column. Frothers, as defined by flotation operators, are compounds that are used specifically for the purpose of creating a froth in a flotation separation. How- ever, some collectors produce froths that are adequate for some flotation operations. Although this chapter is chiefly concerned with the specific frothers used in flotation, some discussion of frothing collectors is included. Otherwise, collectors (or promoters) and modifiersare not discussed at length; for information on these types of flotation chemicals, the reader is referred to other sections of this book or to other sources.l HISTORICAL DEVELOPMENT OF FROTHING AGENTS Historically, there are two distinct phases in the development of frothing agents and other flotation chemicals: 1) 1860 to 1920-oil flotation, and 1921 to date-chemical flotati0n.2~3 Early in the first period, large quantities of fatty and oily materials, up to 10 to 20% of the weight of the ore, were used as a means of separating the sulfide and oxide components from the gangue minerals in ore pulps. Later, various gases replaced these large quantities of oil as a buoyant and separating medium, decreasing oil requirements to less than 1% of the weight of the ore. With this reduction in oil

Jan 1, 1962

By Oleg N. Tikhonov

Control of ball mill grinding circuits is important due to the enormous consumption of electrical energy in mineral processing and other industries. Optimal control requires preliminary detailed studies of static and dynamic characteristics of the process. In this paper a study of nonlinear dynamics is presented with a view toward application to automatic control and the achievement of maximum grinding rate at minimal energy consumption. The study begins with Zagustin's equation (1935) of grinding kinetics [ ]

Jan 1, 1984

By J. A. Jargon, H. K. van Poollen

Flow of slightly compressible fluids through porous media can be described by linear equations. Many mathematical solutions- are available for the boundary conditions of constant terminal pressures or constant flow rates, or a combination of both. Various techniques of formation evaluation use drastic rate changes, such as sudden shut-in. Other methods require that the well be produced at a constant rate. In practice, one is not always able m fulfill these rigid requtirements. This report shows a methor1 by which varying-rate data can be converted to a constant-rate pressure response, called the unit response function. After obtaining the unit response function, one may analyze it, using techniques described in the literature. The method uses tile principle of superposition. Necessary data is a time history of pressure and production. If pressure changes and/or rate changes are very drastic, the unit response function becomes erratic and oscillates The erratic and oscillating results are obvious, and under those circumstances, no answer can he obtained. It appears, however, that a response function without oscilla-tion will not contain any appreciable errors —- one gets either good results or no results. This report includes a mumber of examples of converting constant-rate data to constant terminal-pressure data and vice versa. In addition, a number of field-test applications are given. This method should be useful in converting mathematical solutions from one boundary condition to another. It already has proven useful in converting varying-rate data to constant-rate conditions. INTRODUCTION Pressure drawdown tests are performed on production wells to determine various reservoir characteristics, including permeability, distances to discontinuities, reservoir continuity and wellbore conditions. An ideal drawdown test is performed at a constant production rate with pressure observation during the drawdown period. A typical drawdown curve for a constant rate of production is shown in Fig. 1. In practice, a constant production rate cannot always be maintained. Fig. 2 shows a pressure drawdown curve for a varying rate. Usual methods of analysis are not applicable to tests such as this. It is, therefore, necessary to convert the varying-rate data somehow, before usual analytical techniques can be applied. This report describes a method of obtaining a response function. A response function can be defined as the relationship between pressure and time for a well producing at a constant unit rate. Such a response function can be analyzed by the usual analytical techniques. Hutchinson and Sikora' first approximated a resistance function (response function), and by applying the superposition principle, pressures were calculated using the varying rates. If no match was obtained, adjustments were made to the response function and the closer approximation was used again in an attempt to match calculated and observed pressure behavior. If a good match was obtained: the response function was then used to extrapolate the future aquifer behavior.

Jan 1, 1966

By P. A. Fisher, J. B. Wilson, D. J. Whitehead, C. J. P. Ball, A. C. Jessup

The properties of a new magnesium alloy ZT1 containing 3.0 pct Th, 2.5 pct Zn, 0.7 pct Zr are described. The alloy possesses good creep and fatigue resistance up to 650°F, is free from microporosity, and is readily sand-cast. ZT1 is shown to be superior to zinc-free Mg-Th-Zr alloys. THE advent of the jet engine created a demand for a light sand-casting alloy capable of being cast into large complex shapes and capable of resisting creep at temperatures up to 500°F. This demand has been largely met by alloys of the magnesium-cerium mischmetal-zirconium types, containing about 3 pct Ce mischmetal and 0.7 pct Zr, typified by Elektron magnesium alloys MCZ and ZREI, the latter alloy also having a zinc addition of 2.5 pct. These alloys utilize the valuable properties at elevated temperatures conferred by the addition of rare earth metals to magnesium, a fact which has been known for many years and discussed by several investigators.1-1 Murphy and Payne8 showed that the addition of the powerful grain-refining element zirconium to Mg-Ce mischmetal alloys produced alloys with attractive room temperature properties combined with good creep properties and castability. With the increasing power of modern jet engines the temperatures to which some of the magnesium parts are subject are likely to exceed the safe working range of the cerium-mischmetal-containing alloys, and at the beginning of the research considerable interest had been shown by aeroplane engine designers in a magnesium sand-casting alloy suitable for service at higher temperatures, e.g., 600°F and above. At an early stage in the development of this type of alloy a check on the fatigue properties at elevated temperatures indicated that, since the fatigue limit even at 108 eversals was appreciably higher than any permissible creep stress, the main emphasis of the research could be concentrated on creep behavior. The primary aim in developing the new alloy has therefore been to attain maximum creep resistance; but due consideration has also been given to other important properties such as castability, tensile strength, and cost. It is by now well established that it is not possible to correlate creep strength with other short time mechanical properties such as are obtained in tensile

Jan 1, 1954

By E. W. McAllister

The decision of the California Oil Umpire's' office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in thcir respective wells. Shortly therefter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clark and C. B. Kimberlint in a report2 dated March 1933. PRODUCTIVITY Index In the majority of individual well problems involving the use of subsurface- pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettlcman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time fur various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By E. W. McAllister

The decision of the California Oil Umpire's' office to accept well potentials established from subsurface-pressure data has brought to the attention of many operators for the first time the application of such data to production problems. This paper reviews the development and application of subsurface-pressure data in kettleman Hills, where these data have been used in production work since 1932. The Kettleman Hills field was discovered in October 1928. The first subsurface-pressure surveys were made early in 1932 and by the middle of 1933 the two major operators in the field were making routine pressure runs in thcir respective wells. Shortly therefter, these companies agreed to exchange pressure data, and later a third company entered into the agreement. This made it possible to analyze the effects upon the reservoir pressure of past production practices, which are discussed in the latter part of the report. It is interesting that many of the applications of subsurface-pressure data discussed herein were anticipated by C. L. Clark and C. B. Kimberlint in a report2 dated March 1933. PRODUCTIVITY Index In the majority of individual well problems involving the use of subsurface- pressure data, it is necessary to use a factor known as the "productivity index," which indicates the ability of a well to produce and represents the number of barrels of oil or oil and water per day that will enter the well bore for each pound per square inch pressure drop made opposite the producing interval of the well. The productivity index may be determined from pressure and production data for one or more rates of flow and a static or shut-in pressure survey or from production and pressure data for two or more rates of flow. Productivity indices may be based upon either net oil or total fluid production. All indices referred to in this report are based upon net oil. The value of the productivity index for Kettlcman Hills wells decreases generally with time and it is not uncommon for the index to vary in value at any specific time fur various rates of flow. The decline of the productivity index may be attributed partly to the loss of reservoir pressure. As the reservoir pressure decreases, gas originally in solution is released from the oil, congesting the flow of fluids through the formation and increasing the viscosity and surface tension of the oil; thus the flow resistance of the fluids through the formation is increased, resulting in a decrease of the productivity index. For convenient reference, the productivity indices for each well are plotted against time and a curve is drawn through the points showing the trend of the average index value. Plotted on Fig. I are index values for five

Jan 1, 1941

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By C. Baldwin Sawyer

During the last half century, much time has been devoted to investigations of the effect of nitrogen on the physical properties of steel, but in all discussions of results there is considerable doubt as to the accuracy and interpretation of analyses. No conclusions concerning the effects of nitrogen on the physical properties of steel can be more reliable than the methods used for determining the quantities of nitrogen present. The work described in this paper endeavors to establish some additional conditions required by the customary distillation method for reliable and nccurate determinations. Results by a combustion method of analysis for total nitrogen content are presented; these indicate that all of the nitrogen in steel, exclusive of that contained in blowholes, may be determined by the distillation method. Based on these more sound and more reliable analyses, results havc been obtained that bear on the following divisions of the general subject, nitrogen in steel: Nitrification of steel by melting in nitrogen, nitrification of steel by heating in ammonia, decomposition of nitrified steel by heating, and thermal analysis of nitrified steel. Consideration of Two Methods of Analysis and Some Results The details of the distillation and combustion methods are chemical in character and of little interest to most readers. They are therefore described in an appendix. The distillation method is essentially that described by Hurum and Fay1 and was generally used throughout this work. It is capable of the greatest accuracy and all results given are significant to the last, figure. Where analyses do not check, the samples

Jan 1, 1923

By L. Cichowicz, K. K. Millheim

The constant-rate drawdown test performance for a low-permeability, verticany fractured gas well was investigated. A series of gar wells were tested by flowing each well at constant rate until the data could be analyzed using con-ventional radial flow theory. Each well was then shut in to build up. After a sufficient buildup was obtained, another flow Iest commenced but at a higher flow rate than Ihe first test. Again, the well was shut in when radial fiow was obtained. his procedure was repeated for three to four different flow rates. Two wells in the San Juan basin were tested using this procedure. Both wellere fractured after completion, cleaned up and then shut in until flow testing commenced. Test designs of both wells permitted investigation of the most realistic values of egective permeability, wellbore radius and turbulence factor. Also, being able to determine the eflective fracture flow area and vertical fraclure efficiency was inherent with this testing approach. It was observed that fractures in both wells influenced the Pressure behavior for approximately Is to 40 hours (depending on the flow rate) before radial flow was evident. After this time, drawdown data were analyzed using radial pow theory. When a low-permeability gas well has vertitally oriented, induced fractures, the early flow geometry ic. essentially linear. It will be shown how to determine when a flow test has been conducted long enough so lha' the most representative values of effective permeahiiity. wellbore radius and turbulence factw can be calculated. From the linear pressure data, valuable information about The fracture treatment, such as the effective flow area and vertical fracture efficiency, can be determined for vertically froctured wells. Introduction During tests on gas wells in the Sari Juan basin7 initial transient behavior lasted for many days because of the low permeability of some porous media. As a result, stabilized flow performance could not be obtained. If these wells received some type of stimulation treatment, early pressure behavior deviated from conventional theoretical radial Row. When conventional radial flow theory was used to analyze these low-permeability fractured gas wells, larger values of flow capacity and absolute open flow potentials (AOF) sometimes resulted. Wells were assigned open flow poten- tials that proved to be 3 to 10 times higher than the well would sustain over a longer period of production. In some cases where the wells had flowed for longer periods of time during a constant-rate drawdown test, it was noticed that the effective flow capacity appeared to be decreasing with time until a certain value was reached. The early nonradial pressure behavior can be explained If linear flow is assumed. Rusell and Truitt mathematic. ally investigated the vertically fractured well in a bounded area. They showed that early flow behavior was essentially linear and, for x,/x. approximately less than 0.10 radial flow was obtained after short periods of time. Then realistic values of effective permeability and skin could be determined. Scotta experimentaliy studied the vertically fractured well with a heat flow analog. He showed that earb flow was linear, Both studies indicate that, for small values of x,/x,, linear flow approaches radial flow if the well is tested long enough, To help prove this concept of early linear flow caused by induced vertical fractures, two low-permeability gas wells were tested. Both wells received large fracture treatments prior to testing. A vertical fracture was indicated from the analysis of fracture treatments, As anticipated, tests of both wells indicated early linear flow that was later followed by a period of radial flow, Data collected from each well were analyzed. From the well tests, plus other information on each well, the effective permeability, wellbore radius and turbulence factor were calculated. Effective fracture flow areas calculated from test analyses for each well proved to be approximately one-fourth the created area calculated from classic hydraulic fracturing theory: other fractured wells that were tested but not presented in this paper also indicated that the effective fracture flow area was one-fourth to one-third the created area predicted from hydraulic fracturing theory. The vertical fracturing efficiency was estimated from the calculated values of effective wellbore radius and fracture flow area. For the two wells tested, calculated fracture lengths x, were 112 and 105 ft, and the vertical fracturing efficiencies E, were 122 and 183 percent. Development of Flow Model Agnew' showed that most induced fractures below 1,500 ft are vertical. Anderson and Stah15 indicated that most of the fractures they studied were vertical. Thc model proposed for early flow in most vertically fractured gas wells is shown by Fig. 1. This model should approximate early flow behavior until radial flow is reached, at which time a radial model with an effective wellbore radius of 0.5 they will

Jan 1, 1969

By Paul Gordon, A. S. Iyer

Apreliminary investigation has been carried out on the annealing behavior of explosively deformed copper as compared to that of conventionally deformed copper, using hardness, stored energy, and the sharpening of X-ray spots on Debye rings as the measures of annealing. Some metallographic observations were also made. Two purities of copper were studied. The first was tough pitch copper obtained as a small piece from the guard ring of a sample explosively deformed to approximately 500 kbars.* The second consisted of mentedand deformed these samples quite badly so that only a few small fragments were available for the annealing experiments. As a result, little in the way of quantitatively significant data was gleaned from the measurements. However, several important qualitative differences between the annealing of explosively deformed and conventionally deformed copper have been observed. It is these effects which are described in this report. Fig. 1 presents the results of hardness and stored energy measurements during the annealing of the high-purity copper after explosive and after conventional deformation. The data for the conventionally deformed copper were taken from the work of Gordon;' in this copper it is evident that most of the stored energy is released concommittantly with the hardness drop. As shown in orddon's' investigation, these effect:: are definitely associated with recrystal-lization. In the case of the explosively deformed copper, on the other hand, a large fraction of the stored energy is released before any appreciable hardness change takes place. At 160°C about 40 pct, and at 170°C about. 80 pct, of the stored energy appears to have been released prior to the onset of softening, i.e., undoubtedly prior to recrystallization. In view of the facts that the hardness and energy measurements were made on separate samples and that there is reason to suspect that the intensity of the explosive deformation from sample to sample may not have been uniform, a check run was carried out in which both energq release and hardness changes were measured cnn the same sample. The results of this run, shown in Fig. 2, confirm the conclusion that much of the stored energy is released before the hardness begins to change appreciably. In an effort to obtain some idea of the activation energy associated with the early release of energy, a single callorimetric sample was annealed in two steps, first at 149.5"C and then at 159.5"C, Fig. 3.

Jan 1, 1962

By J. N. Houser

THE industrial relations between the Tennessee Copper Co. and its employees have developed a number of interesting things and have been most, profitable to the employees and to the company. It is noteworthy that considerable has been done without a formal organization of any kind built up through the efforts of the company. From time to time there have been discussions regarding the advisability of a formal organization and the decision has always been in favor of the present method. In the year 1919, the company was dealing with its employees through union committees and, after an understanding was reached, satisfactory results began to be obtained, but as time went on the committees did not function and it came to a question of how to reach the men. For the past two years, about once a month, but at no stated time, there has been a meeting with a committee of employees consisting of 40 or 50 men out of 700. This committee is secured by notify-ing the locals. In addition, the Service Department notifies a number of men not represented in the union, so as to have a large representative committee. The meetings are on company time and the men are rotated, so that in time every employee attends , at least one meeting. All department heads and a number of foremen also are present. The operating plans and policy of the company are set out at the meetings and the market outlook for products is discussed. Explana-tions are also given of anything that has come up since the last meeting which affects the employees, and an effort is made to inform them of what will probably happen in the next month or two. Once a week there is a meeting of department heads with the manager, for discussion of all operations as a whole and such depart-mental details as seem advisable. When the depression started, it was necessary to curtail operations and the reasons were carefully explained; before the men were laid off, the employees as a whole were advised of the coming layoffs through these meetings. They were also advised generally who would be retained and given an opportunity to express their agreement or their. disapproval. In fact, an effort was and is being made to keep the employees advised in advance of matters affecting them and to give them full opportunity to express themselves.

Jan 12, 1922

Discussion of the paper of EZEQUIEL ORDOÑEZ, presented at the Pittsburgh meeting, October, 19.14, and printed in Bulletin No. 94, October, 1914, pp. 2531 to 2536. DAVID T. DAY, Washington, D. C.-Dr. Ordoñez is really the pioneer in the study of the occurrence of Mexican oil. His studies came at such an early time as to prove really prophetic. He was successful in pointing out the relationship of these oil deposits to the volcanic teeth which are so very characteristic as a geological feature in the coastal plain of Mexico. At that time only the first wells around Ebano had been drilled, and drilled under the direction of Dr. Ordoñez himself. Only these Ebano wells were available for a real study of the condition of the occurrence of oil, the other large gushers not then being known. From that time on, the study of the geology of the country has, in large measure, been able to keep up with the oil development. As usual, a great deal of haphazard work in the exploration of the oil fields has been carried on. The results have been good, bad, and indifferent. We know a great deal more about the distribution of oil in Mexico than we do about the geology of it. Two ideas have become prevalent in regard to the Mexican oil, due to the peculiar development there: (1) That oil is omnipresent over a tremendous area bounded by De Soto La Marina, in the province of Tamaulipas, on the north, to south of Tuxpam in Veracruz; and (2) that there are very few spots in all this region which have rich gushers. The truth is somewhere between the two. The amount of land taken up, chiefly by three or four large companies, is extremely great, and covers all the possible chances. The idea that oil is going to be discovered in a large percentage of the land taken up by the oil companies, seems to me entirely unjustified. The amount of oil that will be produced from comparatively small spots here and there over that territory and other territory, undoubtedly will be very great. I do not think there is any hope of multiplying the capacity of these large gushers by the area of that part of Mexico in which they are contained, as a, large number of promoters are inclined to do.

Jan 4, 1915

By F. E. Bash

Previous to the war, this country depended on Europe for its supply of a number of alloys of great importance in the manufacture of electrical apparatus and equipment. When this source was cut off shortly after the beginning of hostilities and the small stocks in the United States were exhausted, either inferior substitutes had to be used or the manufacture of the apparatus suspended. Since electrical equipment was of primary importance in the prosecution of the war, the substitutes had to be used until the composition and processes of manufacture of the alloys could be determined. Included among these alloys was one generally known as manganin, which is composed chiefly of copper and manganese and which, beside having a low-temperature coefficient of resistance, has a low thermal electromotive force against copper. These qualities make it valuable for the manufacture of electrical instruments and machines in which it is used in the shape of wire, rod, and strip. As a result of these circumstances, an investigation was started to determine how manganin could be made on a commercial basis so that a product of uniform quality and the necessary electrical characteristics could be produced. The object was to procure an alloy with temperature coefficient of resistance not greater than 1 X 1X per " C. and a thermal e.m.f. against copper no greater than that of the imported material. It is characteristic of manganin that the temperature-resistance curve is not a straight line but has a peak, which varies in position with different samples; it is most desirable, however, to have it at a temperature of 25' C. if possible. The coefficients of manganin from all records available ranged from a large negative to a large positive value. The composition as reported by different authorities is given in Table I. Prof. Matthew A. Hunter, of Rensselaer Polytechnic Institute, made up a number of small melts of manganin in a graphite crucible and the one that he reported as having the best cocfficient gave the following analysis: Copper, 83.6 per cent.; nickel 2.5 per cent.; manganese, 13.6 per cent.; iron, 0.3 per cent. An analysis of a sample of German manganin gave the following: Copper, 82.6 per cent.; nickel, 3.8 pcr cent.; manganese, 12.8 per cent.; iron 0.7 per cent.

Jan 1, 1921