Search Documents

By Kingman, Robert I.

SUFFICIENT testing has been .performed with the Dutch State Mines Cyclone for thickening and desliming flotation feed at the concentrator of the National Lead Co., Tahawus, N. Y., to prove its application for this work. It is the purpose of this article to present some of the test results, operational details and advantages of cyclone thickening and classification. The metallurgy of the mill operation was described by Frank R. Milliken, assistant manager of the titanium division.

Jan 1, 1950

By H. Groeneveld, C. A. Connally, P. J. Hoenmans, J. J. Justen, W. L. Mason

A miscible displacement pilot using a slug of LPG driven by separator gas was conducted in the Cardiurn reservoir of the Pembina field. The injection pattern was a 10-acre, inverted, isolated five-spot. Upon completion of the LPG-gar phase, an experiment was conducted using a slug of water followed by gas. Calculated performance of the pilot is compared with actual performance. Equations are developed to calculate the distribution of LPG into zones of varying permeability, to estimate the progress of the flood at different times in the various zones and to estimate gas rates after breakthrough. The analysis indicates that permeability stratification was a dominant factor in controlling oil recovery and that oil was completely displaced from the swept pore volume. The results of the pilot indicated that miscible flooding is a practical means of pressure maintenance in this reservoir. The total recovery from the pilot area was good in spite of the early breakthrough of LPG. The effects of stratification were reduced by injecting a slug of water into the partially swept reservoir. INTRODUCTION The Pembina field,' located in Alberta, is the largest oil field in Canada and one of the largest in the North American continent. The reservoir is a stratigraphic trap producing from the Cardium sand. Neither bottom water nor free gas has been found. The recovery of oil by the natural depletion mechanism has been estimated at 12.5 per cent. Pressure maintenance studies of various areas have indicated that the recovery can be increased 21/2 times by water flooding, and a large area of the field is presently under water flood. However, reservoir studies of the North Pembina area indicated that miscible flooding might be competitive with water flooding. A pilot test was conducted to evaluate the performance of a miscible flood. A 10-acre, inverted, isolated, five-spot pattern was selected for the pilot. The pattern area was large enough to minimize wellbore fracturing effects and contained sufficient oil to provide significant working numbers. The performance of each of the four producers could be evaluated individually and compared. In the event of breakthrough in one direction, the effect would be isolated from the other producers. The use of a single injector minimized the volume of LPG required, and, because of the high mobility of gas, one well was sufficient to inject the necessary daily volume to replace the high rate of production. With four producers, the test could be completed in time for results to be evaluated, additional engineering studies to be made and a unit to be formed before the reservoir pressure in the North Pembina area declined below the bubble point. The pilot was located in an area developed on staggered, 80-acre spacing. The injection well was drilled at a regular location, while the four producers were drilled 467-ft north, east, south and west of the injector. Each quadrant and its associated producer were identified according to their direction from the injector— that is, north, east, south or west. The eight surrounding producers on 80-acre spacing were shut in to isolate the pilot area and provide for reservoir pressure observation. The pilot wells were completed using permanent-type completion techniques. After coring, casing was run through the pay section and cemented. Inside 51/2-in. casing, 2 1/2-in. tubing was hung. The wells were perforated opposite the Upper Cardium sand and lightly fractured. Fracturing volumes, rates and pressures were low to minimize the extent of the fractures. The fracturing treatments average 1,000 lb of 20-40 mesh sand in 700 gal of a low fluid-loss sand-carrying agent. Feed rates and wellhead fracturing pressures averaged 5.5 bbl/min at 2,535 psig, respectively. After fracturing, the productivity index was measured in each of the five pilot wells. The average PI of the four producers was 0.41 BOPD/psig drawdown. The measured PI'S were approximately the same as PI'S calculated from core analysis data, indicating that the fracturing treatments were just sufficient to overcome

By G. O. Hiers

IN 1948 in the United States, 184,300 tons of lead was fabricated as coverings for electric power and communication cables. Such covering generally is called "sheathing" for the principal lengths of the cables, while the short lead encasements of the joints are called "sleeves." For the purpose of this paper, both lead sheathing and lead sleeving can fittingly be called lead tubing. In the United States in the same year, 34,262 tons of lead was consumed in making extruded lead pipes. Such pipe is employed frequently for water or chemical solution conveyance with gage pressures up to 100 psi. Consequently, the walls are thicker in ratio to diameter than is the case with the cable sheaths. For this discussion, lead pipes can be thought of as tubes or tubing. About 19 centuries ago, the Romans produced metallic lead of about 99.9 pct purity. Evidently this was cast in flat sheets of Y8-in. thickness, for instance. Such sheet of 10-ft lengths was bent around a removable core producing a tube somewhat oval in cross-section and with a typical internal diameter of, say, 3 in. This method of production necessitated a seam or longitudinal joint evidently made by casting the seam metal adherently. The seam metal, as analyzed recently, contains about 1 ½ pct Sn. Blow pipes were said to have been employed when the joint was made. Specimens of such pipe were found both in Italy and in the British Isles. It is believed the pipes conveyed water for drinking purposes and for baths. Numerous specimens are still in existence in a good state of preservation, due to lead's usual inertness in air or water. According to Claude E. Pearson,1 there were various stages in the evolution of lead extrusion presses for making tubes: I. First press by Joseph Bramah, 1797. 2-First successful press by Thomas Burr, 1820. 3-First bridge die press, J. and C. Hanson, 1837. In 1845, Wheatston and Crooke made the first lead sheathed electric cable. Flat lead strip was wound spirally around the insulated conductor. Overlapping edges of lead were soldered. Early cables were also made by pulling insulated conductors into 50-ft lengths of lead tube. Borel in France, and Wesselau are credited with devising the first presses for extruding lead sheaths directly on cables in 1879. In the United States, Eaton, in 188o, and Roberston, in 1885, introduced new presses of improved design. Following Cunningham's original idea of making lead traps and. bends in 1873, the presses apparently were improved and made successfully soon thereafter. Between the years 1930 and 1940, two continuous extrusion presses for lead were developed abroad. One apparently was originated by Dunsheath and made by the Henley Telegraph Works Co. The other was developed by the Pirelli-General Cable Co. CURRENT PRODUCTION In addition to the several descriptive chapters on lead extrusion in Pearson's book, the Metals Handbook2 recently described pipe, sheath, and collapsible tube production. The latter is by impact extrusion.

Jan 1, 1951

By H. H. Kaveler

A summary of the reservoir engineering and related geologic data on the Schuler field, Union County, Arkansas, is presented here in a manner intended to interest both technical and nontechnical readers. The Cotton Valley formation and the Reynolds oolite are oil-productive formations in the Schuler field, but the Jones sand pool, at a depth of 7500 ft., developed with 146 wells on zo-acre spacing, is the reservoir of principal interest. The Jones sand sandstone reservoir is an anticlinal trap typically gas-drive or depletion type in performance. The core analyses from 88 per cent of the wells drilled, together with drilling time and electric-log data, yield an accurate estimate of the "productive" sand thickness and its areal distribution over the pool. Accurate production statistics, monthly reservoir-pressure surveys, and bottom-hole sample analyses when correlated by the "material-balance equation" show unusually good agreement with that principle. Estimates of oil initially in place made by the material-balance method and the sand-volume method are in good agreement at 116 to rzo million barrels. The reservoir-pressure history of the pool reflects the reaction of a reservoir to production, proration and secondary-recovery practices. The cost of the extensive program of reservoir study in the Jones sand pool has been estimated, in order to emphasize the value derived from such an investment through better understanding of a reservoir's reaction to production practices. Unit operation of 140 of the 146 Jones sand wells made possible an effective unitized gas-injection pressure-maintenance program. Res-ervoir-pressure decline was arrested, natural flow was maintained, and pumping and lease equipment were conserved. An increased ultimate recovery of zo million barrels beyond the estimated 34 million barrels primary recovery is indicated at present. Extension of the Jones sand unit to include the undeveloped Cotton Valley formation will permit additional recovery of otherwise uneconomic reserves of oil through wells no longer required in the Jones sand operations. Introduction The Schuler field comprises approximately 4000 acres in and about sec. 18, T. 18 S., R. 17 W. in west central Union County, Arkansas. Three reservoirs are procluctive of oil and gas: the Cotton Valley formation, the Jones sand, and the Reynolds oolite section of the Smackover limestone. The Jones sand pool is the most important reservoir from an engineering viewpoint. It possesses the traditional and somewhat classic characteristics usually associated with an anticlinal trap. Development and operations have followed the dictates of advanced engineering practices. The pool has attracted attention because of the unusually detailed reservoir data obtained, its interesting production history, and the success of the unitized gas-injection pres-sure-maintenance operation now being carried out. The purpose of this paper is to present a summary of the engineering data relating to the field, with particular reference to the more interesting general applications of

Jan 1, 1944

By H. H. Kaveler

A summary of the reservoir engineering and related geologic data on the Schuler field, Union County, Arkansas, is presented here in a manner intended to interest both technical and nontechnical readers. The Cotton Valley formation and the Reynolds oolite are oil-productive formations in the Schuler field, but the Jones sand pool, at a depth of 7500 ft., developed with 146 wells on zo-acre spacing, is the reservoir of principal interest. The Jones sand sandstone reservoir is an anticlinal trap typically gas-drive or depletion type in performance. The core analyses from 88 per cent of the wells drilled, together with drilling time and electric-log data, yield an accurate estimate of the "productive" sand thickness and its areal distribution over the pool. Accurate production statistics, monthly reservoir-pressure surveys, and bottom-hole sample analyses when correlated by the "material-balance equation" show unusually good agreement with that principle. Estimates of oil initially in place made by the material-balance method and the sand-volume method are in good agreement at 116 to rzo million barrels. The reservoir-pressure history of the pool reflects the reaction of a reservoir to production, proration and secondary-recovery practices. The cost of the extensive program of reservoir study in the Jones sand pool has been estimated, in order to emphasize the value derived from such an investment through better understanding of a reservoir's reaction to production practices. Unit operation of 140 of the 146 Jones sand wells made possible an effective unitized gas-injection pressure-maintenance program. Res-ervoir-pressure decline was arrested, natural flow was maintained, and pumping and lease equipment were conserved. An increased ultimate recovery of zo million barrels beyond the estimated 34 million barrels primary recovery is indicated at present. Extension of the Jones sand unit to include the undeveloped Cotton Valley formation will permit additional recovery of otherwise uneconomic reserves of oil through wells no longer required in the Jones sand operations. Introduction The Schuler field comprises approximately 4000 acres in and about sec. 18, T. 18 S., R. 17 W. in west central Union County, Arkansas. Three reservoirs are procluctive of oil and gas: the Cotton Valley formation, the Jones sand, and the Reynolds oolite section of the Smackover limestone. The Jones sand pool is the most important reservoir from an engineering viewpoint. It possesses the traditional and somewhat classic characteristics usually associated with an anticlinal trap. Development and operations have followed the dictates of advanced engineering practices. The pool has attracted attention because of the unusually detailed reservoir data obtained, its interesting production history, and the success of the unitized gas-injection pres-sure-maintenance operation now being carried out. The purpose of this paper is to present a summary of the engineering data relating to the field, with particular reference to the more interesting general applications of

Jan 1, 1944

By H. A. Fisch, A. J. Opinsky, J. L. Bartos

Fort?-six- two-grain bounduries were studied in doped tungsten 1amp wire that had been heated to 3450°K very vapidly. Back-reflection Laue photograms were taken of the grain boundary partners and solved, using a computer. The resulting distribution of large-grain orientations was analyzed. Rotational axes were calculatedfor each grain boundary pair. The axes of least rotation show an anisotropy of rolalional angle. WhILE the orientations of large grains in straight doped tungsten wire have been studied extensively, little has been done to characterize the boundary that separates them. Rosi.1 upon seeing the jagged interlocking boundary in doped tungsten wire. inferred that the grains should have a preferred orientation, and proved it. He interprets his data as indicative of a single ideal orientation—(531)— being parallel to the wire axis. Rieck2, 3 and Mannerkoski' have essentially confirmed this finding. Opinsky, Orehotsky, and Siegle argue that the data suggest that (211)—a plane-is parallel to the wire axis instead. This (211 ) contains the (531). and hence would appear to be a more general case.5 Ahlborn and wasserman6 report that their orientation data stretch from (110) through (531) to (311). This path is the locus of {211 Recently. Opinsky has suggested that the data can be interpreted as a series of ideal orientations that can be related by coincidence relationships to the (110) fiber texture. All these investigators have determined the orientations of the large grains by the back-reflection Laue technique, and they have all obtained similar results. Only Rieck5 as methodically looked at the large grains along a wire. He was apparently not concerned with the relationships of the large grains across their common boundary, but only with their individual orientations. This research was undertaken to fill this gap in the under standing of the mechanical properties of tungsten wire. Only the crystallographic aspects of the problem will be reported here. In addition, the large number of large-grain orientations, which was accumulated in this study. will also be analyzed. EXPERIMENTAL MATERIAL AND TECHNIQUES All of the data were obtained from four pieces of the same 7-mil-diam General Electric tungsten lamp wire. Twelve-inch lengths of the cleaned wire were heated in vacuum by the flick of a switch to 90 pct of the amperes necessary for fusion (a temperature of approximately 3450°K) and held for 1 min. On the basis of other data. it is estimated that the rise time is of the order of 0.5 sec. The four pieces of wire could have come from anywhere within about 18 ft of wire. Consecutive segments of each piece of wire were mounted in bakelite and polished metallographically The polishing procedure followed that described by woods. "nly boundaries between two grains that each occupied the entire cross section of the wire were photographed and X-rayed. The metallographic sample was mounted accurately with respect to the X-ray unit. Steps were taken to read the films as accurately as possible with the conventional Greninger net. The data were then entered into computer programs that solve the Laue film by precisely the same techniques that are used in the solution of the film by means of the stereographic projection. The use of the computer has probably shifted the main source of error from the stereographic plot to the reading of the film. On the basis of several experiments, it is thought that the error associated with the entire process, from mounting the sample through the computer solution, is of the order of about one-half degree. The output of the computer is the direction cosines of the fiducial direction (the wire axis) and the locations of the three cube axes. The former data were used to calculate the differences in orientation between the two grain boundary partners, and the latter were used in the calculation of the rotational axes that could bring the two grains

Jan 1, 1970

By H. H. Kaveler, Z. Z. Hunter

Variation of the horizontal permeability (parallel to the bedding plane) in the vertical section of reservoir rocks has long been observed as a characteristic of a normally heterogeneous system which reservoir rock represent. The use of a recently developed water injection profile device offered opportunity to measure with a high degree of reliability the rate of inflow of water into Burbank sandstone in wells previously cored. Water injection profiles were not correlative with core permeability profiles in such wells. Apparently the vertical permeability substantially influences the flow between strata in a formation in a manner as to void the usual conclusions that have been drawn from consideration of the horizontal permeability measurements alone. The results obtained in comparing water injection profiles with horizontal permeability profiles suggest that many of the usual production operations based upon "selective" behavior or treatment of rock exposed in well bores need to he re-valuated and re-examined. INTRODUCTION Petroleum reservoir rock are heterogeneous systems. Heterogeneity exists in respect to lithologic character insofar as such rock are composed of distinguishable solid phases. Heterogeneity also exists in respect to certain properties, such as porosity and permeability, that vary due to variation of the physi-cal structure of the rock. Except in exceptional cases, both the horizontal permeability (measured parallel to the bedding planes) and the vertical permeability (measured perpendirularly to the bedding planes) exhibit significant variation in any common source of supply. The variation in horizontal permeability. as reflected by con. analyses. has drawn the greatest attention of petroleum technologists probably out of the general notion that the mass movement of fluids in a reservoir is predimonantly in the horizontal direction. Furthermore, in the usual case, the rock permeability measured in the horizontal direction is greater than that in the vertical. The variation of horizontal permeability of reservoir rock has been the basis for developing a number of operating practices and procedures intended to improve the petroleum production operation. Many such procedures are referred to as "selective" in the sense that the practice is intended to control the flow to a more. or less. permeable interval within the common source of Supply. It is often said that such practices are "tailored" to the permeability profile. The practices referred to involve, among others, the following: selective perforation of casing; selective shooting, acidizing and plugging: plugging back to intervals of low permeability; and, regulation of flow to prevent coning of water or gas, or irregular encroachment of water or gas. Certain expressed notions involving a concept of "by-passing," or "trappingl" that are held to be particularly harmful in causing the avoidable loss of recoverable petroleum have grown from observed variations in the horizontal permeability. Oftentimes estimates of the reserve of a common source of supply are tempered by conclusions relating variation in horizontal permeability to recover-ability of the oil-in-place. Certain conclusions attributed to the significance of the variation of the horizontal Permeabilitv often extend to the design and operation of pressure-maintenance projects involving both water flooding and gas-injection. Many advocate increasing the number of injection wells, advocate maintaining uniform and equidistant input-output well patterns, or advocate so-called "dispersed" gas-drive techniques rather than gas-cap injection because the permeability profile of cored wells is supposed to indicate that "by-passing" or "trapping" would otherwise exist. It is important, therefore, to have an opportunity to test whether the variation in the horizontal permeability found through core analyses of a typical reservoir rock is sufficient to establish the paths of fluid flow in a reservoir. It is particularly important to have an opportunity to determine whether flow at the sand face of a well conforms to the permeability profile as established by core analyses. In that manner, the merit of certain 50-called "selective" operating procedures and other notions may be evaluated. The purpose of this paper is to compare horizontal permeability profiles of wells in the Bartlesville (Bur-bank) sandstone with water injection profiles, for the purpose of showing that there is no correlation between the horizontal permeability of a core and the water intake characteristics of a typical sandstone. GENERAL CHARACTERISTICS OF BARTLESVILLE (BURBANK) SANDSTONE The Bartlesville sandstones of Northeastern Oklahoma are off-shore bar deposits.' Although other reservoirs had different processes associated with their deposition or with the formation of their porous, permeable structure, the l!artlesville sandstones on which these field Fields were made are, in every respect. typical petroleum reservoir rock. The permeability of the Bartlesville sandstones shows a typical variation in both the horizontal and vertical direction. Furthermore, the permeability profile logs of wells in any pool are not correlative, even as between wells as close as 660 ft and 330 ft apart.'. The same condition exists in such sand-tones as the Jones Sand at Shuler' and is the ordinary and usual characteristic of reservoir rock. THE FIELD DATA The data reported herein are those obtained from coring of nine wells on the center of ten-acre locations for the purpose of providing water-injection wells in the Bartlesville (Burbank)

Jan 1, 1952

A. G. Cockbain—The paper by Burlingame, Bitsianes and Joseph is of great interest in extending the work done on high grade sinters, particularly that of Hessle, and the development and application to them of the technique of McBriar, Johnson, Andrews and Davies on ironstone sinters. In this laboratory the work of McBriar et al. has also been continued and extended to cover high grade sinters, and a sectioning technique similar to that used by McBriar et al. was attempted on sinter cakes made in the laboratory sinter unit, using magnetite concentrates (containing 64 pct Fe). In these experiments no attempt was made to flush out the products of combustion with nitrogen before cooling. It was considered that free air penetration would occur on only a limited scale with the size of sinter cake made (14 in. sq x 12 in. deep). Chemical analyses of the zones showed generally similar features of those described by Burlingame et al. and especially the FeO rich region at and just behind the flame front, i.e. zones of ignition and combustion. This seems to indicate that the nitrogen atmosphere does not materially affect the states of oxidation in the sinter cake or at least that special care is not required unless the sinter cake is small. Burlingame et al. consider that FeO present has some significant part to play in the mechanism of sintering. This view does not find favor with the author. The reduction of iron oxides in the presence of red hot coke is a well known phenomenon, whether conducted in an atmosphere of nitrogen or in a crucible in air, and in view of the presence of some carbon in the hot sinter, especially just at the ignition zone, cessation of the progress of the flame front will in no way affect the reduction of iron oxides near hot coke. Even in a nitrogen atmosphere some CO and CO, will be generated by reduction and by continual oxidation and reduction of CO as the transfer agent, the oxidation state of the iron oxides can be lowered quite rupidly so long as free carbon exists with enough heat. Knowing the composition of the gas at the flame front (obtainable by probes), it would be possible to calculate the static oxidation state of Fe2O3/Fe3O2 in equilibrium with it and hence obtain a check on the chemical analyses to see if in fact direct reduction of the Fe2O3/Fe2O1 to FeO has taken place. Have the authors attempted this? It appears to this writer that what is required is some means of reducing rapidly the heat content of the ignition zone and immediately behind, and at the same time insuring no oxidation by the air. In ironstone sinters the difficulty of oxidation state of the iron did not arise on account of the very large slag bulk. However, in high grade sinters knowledge of this, and also the mechanism whereby high oxidation states can be obtained in the final sinter, is of great interest. R. D. Burlingame (author's reply)—The question has been raised as to whether the high FeO content found in high-fuel sinters is due to actual reduction at the advancing flame front or due to unavoidable direct reduction during the quenching period. For such direct reduction to have taken place in the freshly-formed sinter, a considerable amount of solid carbon would have had to escape combustion and be available throughout the hot sinter zone during the quenching period. A simple stoichiometric calculation with the limited data available indicates that a zone of freshly-formed sinter over 2 in. wide must have averaged roughly 2 pct C to accomplish the amount of reduction found. Furthermore, the presence of this amount of carbon would indicate that the fuel in the charge had not burned over a narrow front but over a zone at least 2 in. thick. In contrast to such a condition, the data of the present investigation indicate that the combustion of fuel is confined mainly to a narrow front in which high temperatures and reducing conditions favor. the formation of excess ferrous iron.

Jan 1, 1959

By M. H. Mueller, P. A. Beck, W. P. Chernock

HARRIS introduced the term inverse pole figure for the diagrams previously used by Barrett' to represent the volume fraction p(a,ß) of material in various orientations with respect to the fiber axis in a specimen with fiber texture. The direction of the fiber axis with respect to the crystal lattice is specified by the two independent angle variables a and ß. In such a diagram p gives the fiber axis density distribution over the various crystallographic directions. The p(a,ß) may be given in a two-dimensional diagram by means of contour lines (p=con-stant) in a stereographic projection. The inverse pole figure incorporates in a single contour line diagram all the information given conventionally in pole charts for various (hkl) reflections and, therefore, it represents a considerable degree of condensation. Also, it gives this information directly in terms of the volume fraction of the specimen in various orientations, and it obviates the necessity of referring back and forth between the various pole charts in an attempt to interpret them in terms of orientations. Inverse pole figures undoubtedly represent the most adequate method for describing a texture in a quantitative manner and, at least in the case of fiber textures, this method is certainly a practicable one. Harris described1 a simple procedure for determining at least the rough outlines of a quantitative inverse pole figure. This method depends on the measurement of the intensity of X-ray reflections from various (hkl) planes lying parallel to the same specimen surface. In the case of a rod, reflections from a plane specimen surface perpendicular to the rod axis (fiber texture axis) are to be used. Harris has shown that the measured intensities I,,, reflected by crystal planes (hkl), aligned perpendicularly to the fiber axis of a specimen with unknown fiber texture, and the corresponding intensity Iu nkl from a random specimen are related to the p(a,ß) value for the unknown texture by the following equation IAkl/I°Aklw=c/c°.p(a, ß) [1] where C and C° re parameters depending on the crystal imperfections (extinction), surface preparation (e.g., thickness of oxide layer), the absorption coefficient in the specimen, effective line breadth, and instrumental factors. The values of the variables a and ß1 defining the crystal orientation, depend only on the indices hkl of the reflecting plane perpendicular to the fiber axis. Since p, as described by Harris1, is normalized in such a way that upon integration over the total orientation range its mean value is 1, the parameter C/C may be calculated approximately by the summation of Eq. l over all available X-ray reflections hkl, corresponding to a set of discrete orientations (rather than by integration over the complete range of orientations represented by the continuous variables a and ß). From the summation of Eq. 1 1/n SI AKL/I° Akl = C/C. SP(a,ß)/n is obtained where, as stated above 2p(a,ß) =1. n Therefore

Jan 1, 1959

By J. W. Stewart

ONE of the postwar problems posed for mineral engineering educators is the desire of some mature student veterans to finish their college education under the G. I. Bill of Rights as quickly as possible, a desire that is quite understandable. Not only have they lost several years of education, which they wish to make up as quickly as possible, but many are married and have families and want to become productive as soon as possible in order to support their families properly. The obvious solution to this problem, if it really is serious, would appear to be a continuation of the wartime Accelerated Program, as it was carried on in most colleges and universities. As a matter of fact some schools are known to have continued their wartime programs in one or another form. To ascertain just what our mineral engineering schools generally are doing to meet this postwar problem, last April a questionnaire was sent to administrative officers at colleges and universities

Jan 1, 1946

By Eugene F. Poncelet

GLASS squares compressed on edge by steel jaws in poor contact with them developed jagged "partial-contact" cracks caused by the formation of local tensile stresses. Compressed by steel jaws in perfect contact, they developed smooth "release cracks" during release of the pressure, caused by the formation of local tensile stresses during the release of the pressure. All these cracks were parallel to the pressure. A Microflash photograph of a disintegrating specimen under sufficient pressure reveals a network of fractures roughly normal to each other, also "release cracks" and a disintegration cloud. The Griffith theory is amended to account for the formation of a first crack. A new theory, based on the theory of thermal agitation and wave propagation, is proposed to account for the progress, velocity and forking of cracks. The network of fractures is shown to have been caused by reflection at a free boundary of pressure pulses emanating from a first crack. Postulating equal distribution of energy in the pulses emitted on either side by a crack in particles, the smaller fragments are shown to continue fracturing preferentially while some of the coarser fragments remain as residual pieces. As comminution of the smaller fragments proceeds, the solid is reduced to a collection of residual particles of smaller and smaller sizes, accounting for the disintegration cloud. EXPERIMENTAL PROCEDURE Apparatus A crushing device was built, consisting of a steel frame and two polished, hardened steel jaws to crush plate-glass samples. This device was placed between the plates of a hydraulic press (Fig. I). For centering the pressure, the upper jaw was guided vertically and provided with a rounded top. Later it was replaced by a steel jaw ground out of a 2 1/2-in. steel ball, the lower surface being ground to an optical flat (Fig. 2). Four rollers were used to eliminate side thrust. Screws and centering blocks served to center the specimen in the crushing device. Hard steel shims placed under the shoulder of the upper jaw limited the "follow through" of the jaw after failure of the specimen. Stress distribution was first examined with a polariscope mounted on an optical bench, using monochromatic light. It was found convenient to mount polaroid, quarter wave and monochromatic plates directly on the device itself. A Microflash unit* was used as light source for the photographs. A gold-paint pattern was fused on the plate-glass specimens and connected into the spark-

Jan 1, 1944

By Frederick Laist

ABOUT six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electro-negative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection-1 mg. or less per liter.

Jan 10, 1920

By Nicholas J. Grant, Joseph T. Blucher

High-purity aluminum and an Al-10 pet Zn alloy zvere tested in axial fatigue from 80" to 900oF, at struzn vales of 5 and 150 pct per min, at a strain amplitude of 1 pcl. Cycles to failure were recorded as well as the load per cycle during the entive test. Several grain sizes were examined in each material. Examination was made of modes of deformation, initiation and growlh of' cracks, and vecovery mechanisms such as srbgrain formation and boundary migration. Strain rate effects on cycles to failure are first observed ahoi'e 50O0F, the highev vate vesulting in longer lije. Crack initiclion at room temperature may be truns-or iutercrystalline but fructures are transcrystalline. Abore 600'F, crack iniliation and growth ave largely inlercvystalline. Boundary wzigratiotz to 45-deg positions is observed above 70Oo F, and fractrrves are a combination of grain bol~ndary voids and cvacks. It is only in recent years that studies of deformation and fracture which prevail in fatigue at elevated temperatures have attracted significant attention.' Of such studies considerably less attention was given to high strain-low strain rate fatigue. Moreover, the majority of high-temperature fatigue studies were performed at conventional machine speeds (1000 to 10,000 cpm). As it is well-demonstrated in uniaxial creep-rupture series, at high strain rates, even at high temperatures, metals undergo work hardening with little or no attendant recovery or recrystallization thus the nature of deformation and fracture which is observed is similar to that encountered at lower temperatures.'-" Thus, for example, fatigue testing of a stainless steel at 750°F does not involve high-temperature deformation processes,2 and might more correctly be termed "fatigue testing at an elevated temperature". It was the purpose of this work to study deformation and fracture in fatigue as a function of low strain rates and temperature, selecting conditions which would result in grain boundary sliding, migration, fold and subgrain formation, and intercrystalline cracking in high-purity aluminum and a high-purity A1- 10 pct Zn alloy. Grain size was an additional variable. Extensive studies of the deformation and fracture behavior of these aluminum materials in simple creep had been done in the authors' laboratory, and were to serve as a basis of comparison for the observed effects in fatigue:'-'' the range of the creep test temperatures was 80° to 1150oF. MATERIALS AND EXPERIMENTAL PROCEDURE The compositions of the 99.99 pct pure A1 and the A1-10 pct Zn alloy are shown in Table I. Button-head specimens, with a liberal fillet, of 0.20 in. diam and of gage length 0.40 in. were machined from wrought bar stock. The ratio of 2:l gage length to diameter was selected after preliminary tests showed that a shorter length gave a shorter life, probably due to end effects, and after evidence of buckling in longer gage length specimens. After machining, the specimens were chemically polished to remove the worked outer layer, and were subsequently heat-treated to stabilize the selected grain sizes. Both the high-purity aluminum and the A1-10 pct Zn alloy were heat-treated to produce grain diameters of approximately 0.5 and 2 mm in each case. These grain sizes are referred to in the text as fine and coarse grain, respectively. One lot of the high-purity aluminum was heat-treated to produce a still coarser grain size in which the cross section was occupied by 2 to 3 grains. This structure is referred to as very coarsegrained. After heat treatment, the specimens were again electropolished. To avoid complications of both stress and strain gradients in the cross section of the specimen, a hydraulic, axial fatigue machine was designed and built. A button-head specimen, 1/2 in. diam at the head, was firmly gripped in a split-type holder free of any play in the grips. The test temperatures varied from 80" to 900°F. The strain amplitude in all of the reported tests was 1 pct for a total strain amplitude of 2 pct. The strain range was set by precision micrometers and measured by a precision dial gage. Constant strain rates of 5 and 150 pct per min were selected so that high-temperature type deformation and fracture would occur in the higher-temperature tests5,6 The strains and strain rates must be regarded as nominal values because they are based on the original specimen dimensions, which changed significantly as a result of necking and crack propagation, as can be observed from Fig. 8. For the elevated-temperature tests, a thermocouple was inserted into a well in the head of the specimen; the selected temperatures could be maintained with less than ± 5oF fluctuation during the entire test. To avoid changes in grain size before the test, specimens were heated to the test temperature in less than 15 min; similarly, they were cooled to room temperature after fracture with an air blast to avoid or minimize recovery or recrystallization. During the fatigue tests, load vs strain curves were recorded by a strain gage load cell for each fatigue cycle. In addition, the maximum values of load amplitude were recorded for the entire test.

Jan 1, 1968

By T. A. Griffin

Surface mining today is faced with a twin challenge: (1) accelerating the rate of removal of massive quantities of overburden and ore, and (2) replacing comparable high volumes of overburden in the mined-out portion of the pit. It is against this background, coupled with increased demands for fossil fuels worldwide and legitimate environmental concerns, that the role of bucketwheel excavators and reclaimers has been raised to new prominence.

Jan 10, 1974

By Samuel L. Hoyt

Cemented tungsten carbide, a product of a branch of metallurgy which has never possessed more than a relatively minor interest and importance, has recently commanded the attention of engineers, industrialists, financiers and men of business. New methods, new opportunities, new goals, never before considered, have suddenly been brought within the scope of practical realization. It is these results that attract the interest of the world, but we, as engineers and metallurgists, will have equal interest in the product itself and in that branch of metallurgy from which it comes. It seems appropriate, therefore, to speak today on Hard Metal Carbides and Cemented Tungsten Carbide, as the latter represents one of the outstanding developments of recent date in non-ferrous metallurgy. We are interested in the hard metal carbides as a group of related metallic substances and in cemented tungsten carbide as the leading representative of the metallurgy of this group. The literature of this general field is limited, and, bearing this in mind, it seems advisable to attempt to cover the field broadly and to correlate the subject matter, rather than to present a detailed account of any one of its phases. Our annual lecture lends itself admirably to this plan. The quickened interest in cemented tungsten carbide, once its potentialities were recognized, the many sides to the problem of developing the manufacture and use of this new product, and the desire to economize as much as possible in the time of development, have brought many into this work, both in this country and abroad, notably the Osram Lamp Co. and Friedrich Krupp in Germany and the General Electric Co. in this country. It would be presuming too much to attempt to speak too broadly of the present state of the art and science of the hard metal carbides and my remarks arc guided largely by the work done in the General Electric Co., and by our associates in the Carboloy Co. Even here the activities of many in these two groups have centered around the utilization of cemented tungsten carbide, which is outside the scope of this talk. To those whose work is represented in this lecture, it is my pleasant duty to acknowledge their assistance and advice. To Dr. Zay

Jan 1, 1930

By C. E. Lundin

The Ce-H system was investigated in the temperature range, 573° to 1023°K, and the pressure range, 10-3 to 630 Torr, as a function of 'composition up to 72 at. pct H. Families of isothermal arid isopleth curves were plotted from the pressure-terr~perature-composition relationships. From these curves the solubility relationships were determined for the system. The isopleths are analytically represented by equilibrium dissociation pressure equations. The relative partial molal enthalpzes and entropies of solution of hydvogen in the systerrz were calculated fronz the dissociation pressure equulions and are tabulated. The integral free energies, enthalpies, and entropies of mixing in the Ce-H system were determined from the relative partial quantities and are also tabulated. The standard free energy, enthelpy, and entvopy of reaction of the dihydride phase at kcal per kcal per mole H2, and ?S° = -34. 1 cal per deg mole H2, respectively. The equilibrium dissociation pressure equation in the two-phase region is: UNTIL recently very little was known of the detailed solubility and thermodynamic relationships of the Ce-H system. Two previous investigations1,2 are noteworthy. However, significant discrepancies and omissions exist on analyzing them. The work of Mulford and Holley1 on cerium did not clearly delineate the boundaries of the two-phase region, Cess - CeH2-x. The plateau partial pressures were not thoroughly defined and were considerably displaced in pressure compared to those from the work of Warf and Korst.2 These latter authors concentrated their studies primarily from 823° to 1023°K in the pressure range of 1 to 760 Torr. No data were determined to outline the regions of primary solid solubility and the hydride phase. Also the establishment of the plateau partial pressures was rather limited in scope. In neither work was a treatment conducted of the relative partial molal enthalpies and entropies of solution of hydrogen in the single-phase regions and the integral thermodynamic quantities of mixing throughout the system. Therefore, it was the objective of this research to determine the complete equilibrium solubility relationships and thermodynamic data for the system by pressure-temperature-composition studies. EXPERIMENTAL PROCEDURE The cerium metal for this study was donated by the Reno Metallurgy Research Center of the Bureau of Mines. Total impurity content was 0.13 pct with only 60 ppm O. The metal was checked metallographically and contained only minor amounts of second phase compared to cerium from other sources. Specimen preparation was done in a dry box flushed with argon gas. The surface of a small rectangular piece of cerium (about 0.2 g) was filed with a clean, mill file. Final weighing was done in a tared enclosed vial containing argon gas. The specimen was then loaded quickly into the reaction chamber which was purged several times with high-purity hydrogen gas and then allowed to pump to about 10-6 Torr. The furnace was heated to the reaction temperature and the run started. The equipment used to conduct the hydriding was a Sievert's-type apparatus. Basically it consisted of a source for pure hydrogen, a precision gas-measuring burette, a heated reaction chamber, a McLeod gage, and a mercury manometer. Pure hydrogen was supplied by the thermal decomposition of uranium hydride. The 100-ml precision gas burette was graduated to 0.1-ml divisions and was used to measure the quantity of gas and admit it to the chamber. The reaction chamber was a quartz tube. Prior to each run, the cerium specimen was wrapped in a tungsten foil capsule to prevent reaction of the cerium with the quartz. Control of the temperature was achieved within ±1°K. Pressures in the manometer range were measured to ±0.5 Torr and in the McLeod range (10-3 to 5 Torr) to ±3 pct. The compositions of hydrogen in cerium were calculated in terms of hydrogen to cerium atomic ratio. These compositions were estimated to be ±0.01 H/Ce ratio. The technique used to study the equilibrium pressure-temperature-composition relationships of the Ce-H system was to develop experimentally a family of isothermal curves of composition vs pressure. The range of pressure through which each isotherm was developed was from 10-9 to about 630 Torr in the temperature interval, 573° to 1023°K. RESULTS AND DISCUSSION The hydriding characteristics of cerium are iso-morphous with those of the elements of the light-rare-earth group (lanthanum, cerium, praseodymium, and neodymium) wherein the region from the dihydride to trihydride is continuously single phase.' The structure of this phase is fcc.3 The heavy rare earths form a trihydride,2 which is hcp, separated by a two-phase region from the fcc dihydride phase. The Ce-H system is represented by the family of experimental isotherms in Fig. 1. Due to the small scale required to draw the curves, the experimental points are omitted; however, a total of 240 experimental data points were taken to prepare these curves. The solubility relationships can be deduced therefrom. Three distinct regions of partial pressure and composition can be seen. The region of cerium solid solution is represented by the rapidly rising isotherms in the dilute composition range. In accordance with Gibbs Phase Rule only one solid phase, the cerium solid so-

Jan 1, 1967

By Richard W. Smith

THERE are three distinct varieties of phosphate rock, in Tennessee, known commercially as: (a) the "brown" rock, which is the residual pro- duct of the weathering and natural concentration of certain phosphatic Ordovician limestones; (b) the "blue " rock, which is an unaltered phosphatic stratum of Mississippian or Devonian age; and (c) the "white" rock, which is the result of chemical replacement and deposition. Before 1894, South Carolina and Florida had supplied most of the phosphate of the United States, South Carolina leading until that date and Florida from then until the present time. In December, 1893, the blue phosphate of Tennessee was discovered almost simultaneously on Swan Creek, in Lewis County, by two independent parties-by one as the result of a careful and systematic search for a workable deposit of the long known kidney phosphate, and by the other through mistaking it for a "bloom" of coal. Leases were taken and, with further prospecting disclosing other deposits in the region, the development progressed as rapidly as 'could be expected without railroad transportation

Jan 1, 1924

By H. H. Kellogg

Available high-fernperatzwe equilibrium measurements and other thermochernical data have been critically reciewed for sulfation reactions of the type: Recommended values for log K and ?Fo as junctions of temperature are given for thirty-six suck reactions involving twenty-six different metals. Methods of calculation and choice between conflict-ing data are discussed. SELECTIVE sulfation now enjoys a considerable renaissance as a metallurgical unit process due, in large part, to the available of the fluid-bed re- actor—a device capable of the close control of temperature and gas composition necessary for a successful sulfation process. An additional need, however, if sulfation chemistry is to be approached in a scientific manner, is a reliable body of data on the equilibrium and kinetics of sulfation reactions in simple and complex systems. This paper offers a critical review and compilation of equilibrium data on pure sulfates (simple systems). The last such review, by K. K. Kelley in 1935:30 has proven itself most useful, but the existence of many new data makes necessary a re-evaluation of the available information. METHODS OF CALCULATION For a simple sulfation reaction such as MS04(c) = MO(c) + SO3 [1] there are two approaches one may take toward establishing the value of ?Fo or K as a function of

Jan 1, 1964

By Frederick Laist

About six years ago the Anaconda Copper Mining Co. decided to investigate the possibility of extracting zinc from the ores of certain mines in the Butte district. These ores are of a complex character and contain so much iron and lead that the concentrate contains only 33 to 35 per cent. zinc. Investigations showed that while a high-grade concentrate could not be obtained by ordinary methods, such as tabling and magnetic treatment, a fair grade could be made by the Horwood process. In this method, the concentrate resulting from the flotation of all of the sulfides is given a light roast and this calcine is subjected to flotation in the presence of a large amount of sulfuric acid; the resulting concentrate contains most of the zinc and a residue contains most of the iron. The fact that the lead, copper, and silver are divided approximately equally between the zinc concentrate and the iron residue and the large consumption of acid, which ranged from 50 to 100 lb. (22 to 45 kg.) per ton of concentrates, were serious objections to this plan. The zinc recovery, moreover, was low, as a considerable percentage invariably accompanied the iron. While a profit might be made on the ores by the use of this process, it was thought that other and more promising methods might be devised. After carefully studying the field and doing some laboratory work on various processes that had been suggested, it was decided that the electrolysis of sulfate solutions was the most promising. We soon found, as have other investigators, that the only way to obtain a good zinc deposit is to have the electrolyte free from all metals more electronegative than zinc, such as copper, cadmium, lead, arsenic, antimony, etc. Arsenic and antimony are particularly injurious, causing very poor current efficiency and small yield per horsepower when present in amounts so small as almost to defy detection—1 mg. or less per liter. A pure zinc is soluble only with difficulty in sulfuric acid; an impure zinc dissolves very readily. Electrolytic zinc deposited from pure solutions is, of course, extremely pure and dissolves only about one-fiftieth

Jan 1, 1921

By F. F. Aplan, P. H. de Bruyn

The adsorption density of hexyl mercaptan was measured at the gold-solution and the gold-vapor interfaces. This collector is strongly adsorbed at low concentrations, a monomolecular layer being formed at the gold-solution interface at concentrations as low as 2 x 10'6 moles per liter. A maximum contact angle of 83 ± 3° is observed. From a thermodynamic analysis of the experimental data the changes in surface tension at the gold-gas and gold-solution interface are calculated. The data also suggest that the adsorption density of mercaptan at the gold-gas interface exceeds that at the gold-solution interface. In the equilibrium state, a simple flotation system consists of three phases, the solid to be floated, air, and an aqueous solution in stable contact along a line. During the process leading to this final state, a solid-gas interface is created at the expense of a portion of the liquid-gas and solid-liquid interfaces. This change of state is achieved by addition of a collector and, if necessary, suitable modifying agents to the system. By a combined application of the Gibbs Adsorption and the Young Equations, de Bruyn, Overbeek and Schuhmannl were able to show theoretically that the equilibrium distribution of the collector at all three interfaces determines the magnitude of the contact angle. Their analysis led them to conclude that the equilibrium adsorption density of the collector at the solid-gas interface exceeds its density at the solid- liquid interface. This paper succeeded in focussing attention on the neglected role of the solid-gas interface in flotation. In recent years the application of radiotracer, infrared, electrochemical and electro-kinetic techniques to studies of the solid-liquid interface2-5 enhanced our understanding of adsorption processes at this interface. Except for the measurement of contact angles, the solid-gas interface received no attention in fundamental flotation studies. In an attempt to apply the analysis of de Bruyn, Overbeek and Schuhmann to a simple flotation system, an investigation of the adsorption of hexyl mercaptan onto gold was undertaken. Gold was chosen as the solid phase in order to keep the number of dissolved chemical species in the solution phase to a minimum. Hexyl mercaptan (1 - hexanethiol) was selected as collector because its relatively high vapor pressure at room temperature makes it possible to obtain adsorption measurements at the solid-gas interface. This flotation system consists, therefore, of a pure solid phase (gold), an aqueous solution of a weakly dissociated collector (1 -hexanethiol), and a gaseous phase, nitrogen saturated with respect to both water vapor and mercaptan vapor. EXPERIMENTAL MATERIALS AND METHODS Materials: Liquid 1-hexanethiol (C6H13SH) was obtained from Distillation Products Industries and was further purified by double distillation. The purity of the final product was established by boiling point and refractive index measurements. For the adsorption studies from aqueous solution, the radiotracer element, sulfur-35, (half life 87.1 days, 0.169 Mev beta ray) was synthesized into the mercaptan by Tracerlab Inc., Boston, Mass. A close boiling fraction of the synthesized compound was used in the adsorption studies. The specific activity of the radioactive compound was 10 millicuries per gram.

Jan 1, 1963