Search Documents

By R. L. Wiegel

This article proposes a physical model for an idealized binary mineral system and for the process of liberation by size reduction. Based on this model, equations are derived relating the amount of each component liberated as a function of the ratio of the volumetric abundance of the two mineral components and the ratio of the mineral grain size to particle size. A definite relationship is shown to exist between the mineral concentration within a locked particle and the frequency of occurrence of such a particle. These relationships are used to obtain theoretical expressions for the concentration-recovery diagram. Physical mineral beneficiation processes are based on breaking a mineral aggregate to liberate the dissimilar mineral grains and then making use of their physical properties to separate the mixture into its components. The effectiveness of the process is therefore dependent on how well the minerals are liberated and how efficiently they are separated. Although a substantial amount of work is being done to improve our understanding of mineral separation processes, the study of mineral liberation itself has been almost completely neglected. The purpose of this theoretical study is to shed some light on the liberation phenomenon by: 1) proposing a physical model for an ideal binary mineral system, 2) treating mathematically the fracture of this system into liberated and locked particles, and 3) deriving an expression for the liberation characteristics of this system. The results of this study are useful in understanding the effect and importance of various parameters in liberation, and provide a basis for comparison with real mineral systems. 'RANDOM' MODEL It is recognized that liberation can be caused by detachment which results from fractures occurring at the mineral grain boundaries, or by size reduction which restricts the occurrence of dissimilar mineral locking to a portion of the resulting particles. The detachment effect is dependent on the relative strengths of the mineral grains and the bonds between them, and must be treated empirically for each mineral system. The size reduction effect, however, can be treated analytically if certain assumptions are made concerning the shape and geometrical arrangement of the mineral grains.

Jan 1, 1968

By N. T. Burdine

Formulas for calculating relative permeability from pore size distribution data are derived from basic laws of fluid flow ill porous media. The tortuosity factors that appear in the equation5 are described in. terms of the physical properties of tile medium and the saturations of the contained fluids. Procedures for calculating and methods for measuring the tortuosity factors are discussed. Values of relative permeability calculated by the formulas art: compared with results obtained by experimental measurements I INTRODUCTION Recently, several investigators have derived relative permeability equations from Darey's and Poisenille's Laws in which some, physical factor or factors describing the porous system appear. The factor that has caused the greatest amount of comment, and which is probably least understood, is the tortuosity of the fluid {lath ill the porous sample. Values of the tortuosity factors appearing in the equations range from a constant for all condition- of the fluid flow system to an inverse function of the pore radii. It is the purpose of this paper to compare wine experi~i~cntslly determined relative permeability curves with those calculated by a method which utilized capillary pressure infortmation. The capillary pressure data were obtained prefer.. ably from pore size distribution information as determined by mercury injection but. in some cases, in the absence of suitable mercury injection information. data were taken from measurements made by the porous semi-permeable diaphragm method. The physical significance of certain tortuosity concepts is inferred and the determinations of the tortuosity factors from pore size distribution data and by electrical measurements are discussed. THEORETICAL BACKGROUND In previously reported studies on pore size distribution in petroleum reservoir rocks. by the author and co-workers ail equation was derived relating specific permeability. k, to pore entry radii, R, porosity. . tortuosity factor. .,, and incremental pore volume. V. The equation is where being the "effective" length of the flow path in the porous sample. and L the length of the porous sample., The constant. 0.126. is a units conversion factor. (This definition of tortuosity factor X, = L L does not conform to all such definitions found in the literature. Fly similarity, in a two-phase system. the effective permeability of the wetting-phase.

Jan 1, 1953

By E. H. Griswold, W. J. Wilkins

Pressure control of oil wells may be defined as the adjustment of pressures within a well to obtain the most efficient and economic utilization of the natural gas energy with a minimum of sand troubles or irregular water encroachment. The purpose of this paper is to present the methods used by the writers in applying pressure control and a discussion of the various effects occurring within the wells affected. The benefits to be derived from the conservation of natural gas energy have been so adequately discussed and demonstrated in prior papers by various engineers that the effects on ultimate production will not be discussed other than to mention a few representative cases. The detrimental effects of irregular edge-water encroachment and of sanding up arc of general knowledge to the industry. Effect on Ultimate Production One of the strongest objections voiced against pressure control is that of the danger or inadvisability of deferring oil production by cutting the rate of production. It has been our experience that such deferred product'ion is returned within a few weeks or months rather than years and that an increased cumulative oil production is obtained in the early life of the well by conserving the natural energy. In many cases the rate of production is increased rather than decreased by the adjustment of pressures to obtain the minimum gas factor. Fig. 1 shows the history of a Wilcox sand well in northern Oklahoma, which was pressure-controlled from completion. It is noted that during the early months while flowing naturally through the casing the gas factor was decreased rather than allowed to follow its natural tendency to increase. A string of 21/2-in. tubing was run to restrict the flow and resulted in a decreased gas factor with a more sustained rate of production. When first placed on gas-lift the gas factor again tended to increase, but after the proper pressure adjustments were made, remained approximately steady. It was necessary to defer 100 bbl. per day of oil production in order to maintain this low gas factor. In March serious

Jan 1, 1929

By Herbert Hughes

The trend in modern building construction is definitely toward the use of weight-reducing materials. The basic advantage of lighter structural weight is obvious; reduction of dead load with retention of equivalent strength affords the possibility of increasing the live load, or if this is not desirable or necessary it makes feasible a reduction in size of structural steel members and corresponding savings in other phases of construction. Among the weight-reducing materials and practices rapidly gaining favor are the use of light-weight patented insulating board to replace back-up tile or units, particularly in home construction; introduction of aluminum alloys to replace steel for many purposes; manufacture of porous brick, the use of which materially reduces the weight of masonry walls and partitions; and the use of self-rising vesicular concrete, dia-tomite and sawdust tile, porous gypsum, or gypsum tile for nonload-bear-ing partitions and walls. Even building accessories are being designed to save weight and space; one of the most striking examples of this is improved radiator construction. Concrete technique is keeping pace with the rest of the industry. Burned shale aggregates now available in many sections of the country will make concrete weighing only 100 Ib. per cubic foot, saving roughly 35 per cent. in weight and sacrificing none of the strength of a rock-sand mix. It may be more expensive, but actual experience has shown that the saving in dead load will effect a reduction in structural steel which in many instances will more than offset the increased cost of the aggregate. The vesicular nature of most light-weight aggregates gives the concrete especially good insulating, fireproofing and soundproofing properties; yet absorption is compara.tively low. Strangely enough, however, the increased use of light-weight aggregates appears to have augmented the demand for ordinary aggregates in concrete construction rather than to have decreased it. Light-weight aggregates have widened the field for concrete structures and, since the producers do not attempt to recommend the use of their material except where weight or other special properties are important factors, impetus has been given to sales of other aggregates.

Jan 1, 1931

By J. Clair, H. Mirabel

The determination of the temperature and electrical potential distributicms in the cathodes of aluminum electrolytic cells is difficult. The reascms come from the various nature and the intricate three-dimensional geometry of the materials; besides thermal and electrical phenomena react upon each other. A method of calculation using a computer program applied to a mathematical model, figuring the cathode, is developed. Both of the thermal and electrical phenomena are simultaneously considered. Temperature and electrical potential distributions are finally obtained by successive iterations. Results are compared with measurements on industrial cells. Theoretical and practical applications of these studies are given. Up to the present time the study of the distribution of the temperatures and electric potentials in the electrodes, anode and cathode, of the electrolytic cells used for the production of aluminum was limited to one of the two aspects of the phenomena because of lack of a simultaneous method of calculation. For example, the anode or cathode drop was studied assuming that the temperatures in the iron and carbon are known, a method that obviously is very approximate since iron resistivity, in particular, greatly varies with temperature, which in turn depends on current density. Consequently we tried to find a method of calculation simultaneously taking into account both thermal and electrical phenomena. We proceeded to the study of the cathodes as an initial approach to the problem. Although the cathode and surrounding materials may have varied forms and particularly very heterogeneous characteristics, their structures are simpler than that of the Sijderberg anode and boundary conditions are more easily represented than in the case of anodes even though they are prebaked. The study was in two parts: a) development of a model schematizing the true geometry of a cathode and defining the thermal and electrical boundary conditions, and b) working out a method of calculation of the temperatures and potentials by means of an electronic computer. To facilitate solution of the problem, a model was used initially much simplified in comparison with an actual cathode. This model permitted development of the method of calculation. In a second phase, this model was adjusted to the study of actual cathodes and applied to different types of cells: low- or high-intensity cells, cells set up at ground level or above ground level, cells with cathodes more or less heat-insulated. Simultaneously measurements were made with cells equipped with cathodes of the types studied to compare the values resulting from calculation. The initial model was also used for general studies, in particular for studying the effects of current density in the carbon and iron. The results were confirmed or made precise by the model of the true cathodes. This report successively describes: a) the manner in which the model representing a cathode was worked out, with the simplifications and/or the hypotheses used, b) the method of solution of the problem by means of the electronic computer, and c) an example, stating the extent to which the results obtained may be realistic. Further the possibilities offered by such a study are examined. 1) CATHODE REPRESENTATION The purpose of this phase is to represent the cathode in the form of a so-called "mathematical model", that is with a simplified geometrical configuration, in order to meet the subsequent calculation requirements, while keeping to the true facts as closely as possible. This model further includes the thermal and electric conductivities with regard to temperature for the varied materials composing the cathode, as well as the thermal and electrical conditions at the model boundaries. 1.1) Guiding Principles. For calculating the temperatures and potentials the model is divided by trior-thogonal planes into a network of small elementary parallelepipeds. At the summit of these parallelepipeds' so-called mesh points, the temperatures and potentials are computed. The number of mesh points is of course limited by the capabilities of the computer, since 1) the number of equations to be solved depends on the number of mesh points selected, and 2) the amount of time spent by the computer considerably increases with increasing this number. These conditions call for the following requirements as concerns the model: a) Dimensional requirements: the calculation will be all the more accurate as the network is more closely meshed. Since the number of mesh points is limited in practice, it is necessary to restrict the dimensions of the model. b) Geometrical requirements: so as to make things easier in working out the network, the model must be given a simple geometry. In particular, it will be convenient to have the cathode so constituted that the surfaces limiting the cathode and the surfaces within the cathodes separating the different materials consist of triorthogonal planes. 1.2) Schematization of the Cathodes. After the tech-

Jan 1, 1968

By G. S. Hume

Activity in geological exploration and drilling continued in Canada in 1945 at about the same rate as in the previous year, but with disappointing results as far as new production is .concerned. Both in the foothills and on the Plains of Alberta, however, there are wildcat wells that have either given encouraging shows or some production, which are very important in relation to future developments. The normal decline of Turner Valley, the largest producing field in Canada, has continued, and this decrease has not been offset by new discoveries. In addition, the closing of the Canol pipe line on March 31, 1945, isolated the Norman Wells field in the Mackenzie River valley, and the outlet at present. is confined to supplying the relatively small local requirements. This

Jan 1, 1946

By A. L. Barnes, A. M. Rowe

A heat transfer study was made of hot gas injection into oil shale through wells interconnected by vertical fractures. This analysis involved the simultaneous numerical solution of a nonlinear, second-order partial differential equation that describes two-dimensional conduction heat transfer in oil shale and a nonlinear first-order partial differential equation that describes convection heat transfer in the fractures. Three nonlinear, temperature-dependent coefficients were used in this work; they are thermal conductivity, thermal capacity and retorting endothermic heat losses of oil shale. Vertical fractures were considered to be of finite height. Although vertical conduction heat transfer was not considered, an estimate of the error resulting from this limitation was made. The effects of injected gas temperature, injection rate, system geometry, cyclic injection and time upon retorting efficiency were investigated. Results from this study show that the rate of retorting oil shale is a direct function of both injection temperature and rate, and the theoretical producing air-oil ratio:(AOR) is an inverse function of temperature. Retorting rates are constant until "breakthrough" of the 700 F isotherm at the producing well, assuming constant injection parameters. Retorting rates for bounded systems are higher than the analogous unbounded systems and likewise AOR's are less. The use of an alternating injection-soak routine with high injection rates is less efficient than continuous injection at lower rates. These results indicate that injection temperatures on the order of 2000F or greater may give theoretical AOR's in the economic range. INTRODUCTION Over half of the known oil shale reserves are located in the U.S., and most of them lie in the Piceance Creek basin of Western Colorado. The Colorado oil shale outcrops on the edges of the Piceance Creek Basin. At the outcrops the shale beds are relatively thin, from 25 to 50 ft thick. In the center of the basin the oil shale is as great as 2,000 ft thick and is covered with 1,000 ft of overburden. It has been estimated that there are over 1,000 billion bbl of oil in shales having an oil content over 15 gal/ton in this basin. Oil shale does not contain free oil but an organic matter called kerogen. Kerogen yields petroleum hydrocarbons by destructive distillation. It must be heated to approximately 700F, at which temperature it decomposes into shale oil, gases and coke. The U.S. Bureau of Mines and, more recently, oil companies have conducted considerable research on surface retorting methods to economically recover oil from this shale. Another approach to exploit the oil shale deposits, in particular that portion having 1,000 ft of overburden, is to retort the oil shale in place and produce the liquid and gaseous hydrocarbons through wells drilled into the shale. Some research has been done on this approach.l,2 There are several variations to the in situ retorting approach. These variations fall into one of two groups, depending upon the geometry of the system: (1) retorting in a highly fractured or broken up matrix; (2) retorting from single fractures between production and injection wells. The latter is the group studied. Several investigators,3-6 using various assumptions, have studied flow of heat through horizontal systems. The objective of this work was to make a heat transfer study of in situ retorting oil shale by hot gas injection through wells interconnected by single vertical fractures of finite height. The oil shale thermal conductivity, thermal capacity and retorting endothermic heat losses were considered to be functions of temperature. A knowledge of the

Jan 1, 1969

By Dever C. Ashmead

COAL companies in the anthracite region are studying various methods of mining that will permit a considerably shorter life of gangway and therefore a decrease in the maintenance charges. Maintenance charges in the upkeep of gangways where the measures are steeply pitching are high due to the excessive cost of the replacement of timbers and the cleaning up of falls. Therefore, if the length of gangway in the coal beds can be decreased and the mining more concentrated, the life of the coal gangways will be decreased and consequently the maintenance charges will be lower per ton of coal produced. Customary practice in the anthracite region is to drive long coal gangways and to work the breasts as the gangway from which they were driven is advanced.

Jan 1, 1925

By J. M. GARZA

The production of oil in Mexico during 1945 was 43,402,852 bbl., or a daily average of 118,912 bbl. In March 1938 most of the oil properties were taken over by the Mexican Government and since then have been operated by Petroleos Mexicanos, an agency of the Government. The variations in the production during the last 8 years have been due to- fluctuations in the export market demand for Mexican oil rather than to the productive capacity of the fields. Since 1937, yearly production, to the nearest hundred thousand barrels, has been as follows :

Jan 1, 1946

By F. H. Bunge, W. H. Jr. Dailey

This paper covers an investigation of the magnetic roasting characteristics of several iron ores when treated in the form of small pebbles (1/8" to 1/2" in size), and in the form of balled fines. The roasting treatment was carried out with apparatus capable of very close control of time, temperature, face velocity, and per cent combustible in the reaction gas. The effect of rapid initial heating was not studied although it is believed that this has a major effect on the results when processing solid pebbles. The test equipment is a fixed bed type, with such a wide range of gas velocities, temperature, combustible content and etc., that the results obtained can be made to approximate those from various commercial roasting processes. The data presented in this report covers reaction rates, effect of processing variables on silica in the concentrate, flow resistance of beds, and to a limited extent, the effect of particle size. The work is far from complete and raises many more problems than it gives answers for. We believe, however, that much of the information will be useful to those engaged in investigation of magnetic roasting processes. We measured the time required for various degrees of completion of the reaction of hematite to magnetite, for finely pound material in balled form and for carefully sized crushed ore. Measurements were made for a variety of Minnesota and Labrador ores. This report covers an ore requiring fine ginding (-325 M) for liberation (Lower Kevin) and an ore requiring coarser grinding (-100 M) for liberation (Upper Olson). These ores represent approximately the range of characteristics for a group in the west end of the Mesabi Range. Our data shows that the reaction rate is very fast for the finely ground material and that tests are readily reproducible. The reaction rate of the larger size material, in the range of 1/8" to 1/2", is much slower and the results more erratic. We found that for the ores tested, the percentage of silica in the Davis tube magnetic concentrate was a function of iron recovery. Normally the concentrate had a low and relatively uniform percentage of silica up to a critical value of recovery. Above this critical recovery value the percentage of silica increased very rapidly. For example, for one particular ore roasted in the form of 3/8" diameter balls made from -28 mesh fines, the silica remained at about 7% to 8% until the recovery exceeded about 93%. Increasing the recovery beyond 93% resulted in over 25% silica with the additional recovery. The degree of conversion of hematite to magnetite (% completion of roast) required to obtain 93% recovery for balled material, varied inversely with the gas flow rate. Percentage silica in the concentrate resulting from roasting 3/16" and 1/2" solid material was relatively erratic. However, for varying degrees of iron recovery the lowest silica percentages corresponded to those obtainable when roasting fines. It is thought the probable reason for the erratic values was the variation in shattering or cracking of the pebbles during initial heating and roasting. There is some indication that very fast initial heating will greatly increase the permeability of the individual particles of ore to gas flow so that the reaction rate for coarse sizes will approach that obtainable with balled fine material.

Jan 1, 1961

By O. R. Wagner, R. O. Leach

Immiscible displacement tests were performed in a consolidated sandstone core over the interfacial tension range from less thdn 0.01 to 5 dynes/cm to better define how interfacial tension (IFTJ reduction can lead to increased oil recovery. Data obtained were displacement efficiency at breakthbrough vs IFT for both drainage and imbibition conditions. These tests simulate water flooding under oil-wet and water-wet conditions, respectively. Results of the study have shown that displacement efficiency under both oil-wet and water-wet conditions can be markedly improved by a sufficient reduction in IFT. In the particular porous media used and for the low pressure gradients employed, the IFT must be reduced to a value less than about 0.07 dynes/cm to achieve increased recovery at the time of breakthrough of the injected phase. Below 0.07 dynes /cm, further small reductions in IFT result in large increases in displacement efficiency. Observed increases in recovery were obtained at pressure gradients which are well below those which can exist in the interwell area of a reservoir under water flood. The effect of pressure gradient on recovery is discussed. INTRODUCTION A residual oil saturation remains in rock which has been water flooded because, under usual reservoir conditions, the driving force which can be generated is inadequate to expel oil trapped by capillary forces. Since these capillary forces can be reduced by reducing the IFT a frequently studied method of increasing oil recovery has been the use of surfactants to reduce the water-oil interfacial tension. Mungan l observed improved recovery in both water-wet and oil-wet systems at 1.1 dyne /cm IFT, finding that the amount of improvement was greater in oil-wet systems. Moore and Blum,2 working with visual flow cell micro-models, con- cluded that recovery cannot be improved in water-wet systems by injecting surfactant solutions. They calculated that, for a pressure gadient of 1 psi/ft in their model, the IFT must be reduced to 0.03 dynes/cm to release oil trapped under water-wet conditions. Berkeley et al.3 indicated that, at representative field flooding rates, the IFT must be reduced to 0.001 dyne/cm to improve recovery, Thus, there is a wide variation of opinion about the IFT levels needed to improve recovery under field conditions. These previous investigators all have used as their experimental method the addition of surfactants to the injected water. The use of surfactant solutions to reduce IFT creates two experimental problems: (1) the loss of surfactant through adsorption on reservoir rock can obscure the true IFT value which exists at the displacement front, and (2) at very low values of IFT emulsifica-tion of oil and water commonly occurs. It is difficult, therefore, to determine whether the increased recovery is caused by IFT reduction as such, or is instead caused by emulsification. Also the properties of the available surfactants limit the IFT range which can be studied. In the present study the purpose is to better define how interfacial tension reduction can lead to increased oil recovery. A matter of great interest is the amount of recovery improvement potentially achievable in this way. The study was made using very low pressure gradients which was well within the range achievable by water flooding in the interwell region of petroleum reservoirs. A unique experimental approach was chosen to avoid adsorption and emulsification problems, and to allow convenient control of IFT. The fluid phases used were the equilibrium vapor and liquid phases of the methane-n-pentane system. The interfacial tension level was varied by changing the equilibrium pressure of the methane-pentane system over the range from 1,200 psia to near the critical pressure (2,420 psia). All tests were performed at a controlled temperature of 100F. The IFT-vs-pressure relationship for the methane-pentane system was based on the data of Stegemeier and Hough,6 and on new data obtained in this study. With this experimental approach it has been possible to study displacement at lower values of IFT than have been previously investigated.

Jan 1, 1967

By D. M. McFarland

A FEW years ago a novel electric detonator known as the split-second or millisecond delay electric blasting cap was introduced for use in quarry blasting. Regular electric blasting caps fired in series may be depended upon to fire within a millisecond or so from the first to the last in a series. Regular delay electric blasting caps are provided that fire one period after the other period in intervals of 1/2 to possibly 1 1/2 sec. Most split-second or millisecond delays are designed to fire one period after the other period in possibly 25 to 50 millisecond intervals. The ear is not capable of detecting time intervals of this magnitude. The primary thought at the time millisecond de- lays were introduced was to investigate the results on rock breakage by firing a line of holes in a quarry face.so that charges in adjacent holes would not be detonated simultaneously. This could not be accomplished satisfactorily with regular delays. The time interval between successive periods of $5 to 1 sec was sufficient to permit considerable movement of the burden. If the burden of one hole was reduced to a great extent by the firing of an adjacent hole, the firing of the hole with the reduced burden would likely reveal this lack of confinement by a terrific report and wild throw of rock.

Jan 1, 1950

By JOSEPH MACDONALD

STRIPPED of its romantic possibilities, mining is a commercial business, carried on for the profit there is in it, and the business of the manager, in its ultimate analysis, is to make the profit as large as possible. The general manager of a mining company should keep himself personally familiar with all the details of its operations. If be fails to do so, chaos results, labor becomes inefficient, costs go up, and profits go down. Nowhere is this emphasized more than in Mexico. If the mining operations are extensive and complex, involving, besides the work of mining the ore, its transportation and treatment by various milling operations, and the marketing of the products, the business, to be carried on properly, must be divided into a number of main departments, which are subdivided into minor departments. Each main department should be under the immediate charge of a superintendent, or a foreman, and each minor department under a shift-boss. Organized in this way, and with all the principal centers of activity connected by telephone, the manager can keep in touch at all times with the details of every branch of the business, and be in a position to perform effectively the full duty of manager. The ?total cost of mining operations may be broadly divided under the heads of Labor, Supplies, and Marketing. Of these, it will be found, on averaging a number of cases, that the cost of labor will be about two-thirds of the total cost. The importance, therefore, of an efficient labor-department will be apparent. This department must be sub-divided and organized differently, according to the peculiar conditions at each mine, and no one system, however well suited for one particu-

Jan 1, 1909

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

By Louis C. McCabe

The control of dusts and fumes of submicron size is involved in many process industries. This paper presents in tabular form the quantitative data from a number of metallurgical operations and discusses allowable discharge in terms of effluent-weight ratio. Typical installations for recovery of stack effluents are cited. THERE are many sources of smoke, fumes, gases, and dusts that may cause undesirable contamination in an industrial area. Fumes and gases are the result of chemical action or volatilization, while dusts are produced in processes of disintegration and dispersion. Commonly, smokes are suspended particles formed by combustion or destructive distillation. Methods for controlling smoke are generally known, and great improvements have been made in equipment for removing fine dusts and fumes from gases. In most of the industrial centers of the country, the chief duty of the air-pollution abatement agency is the elimination or reduction of emissions resulting from improper combustion. Correct methods of firing, proper fuel selection, and installation of properly designed equipment may accomplish this. It is becoming more widely recognized that much of the contamination of an industrial atmosphere is caused by dusts, fumes, and gases that are not related to the process of combustion. As such emissions are usually a functional part of plant operation, they rarely can be prevented even by better design and careful operation. When dusts, fumes, and gases are an integral part of the operation, mechanical equipment must be designed to remove these emissions. Most of the dusts and fumes that should be controlled are less than 1 micron in size. Control of such small particles is largely a new and untried field in many industrial areas. However, where conditions have been critical, effective control equipment for dusts, fumes, and gases has been in operation for many years. The problem is not one of smoke abatement and requires an entirely different set of standards for effective solution. Identical standards need not be applied to all industrial areas because of differences in meteorology, physiography, plant location, plant density, and nature of stack effluents. In this paper, discussion of control of atmospheric contamination by industrial plants refers specifically to the Los Angeles area, but the method of approach is applicable to any area where similar problems are encountered. Quantities of particulate matter reported in analysis of stack effluents indicate the need for standards of emission. Many types of dusts and fumes that contribute materially to the air-pollution problem are discharged into the atmosphere at a lower rate than 0.40 grain per cu ft at standard conditions. On the other hand, some stacks discharge at a higher

Jan 1, 1951

The annual world production of minerals approximates 1,700,000,000 tons, over 90 per cent. of which consists of coal and iron. Of this amount about two-thirds is used within the countries where the minerals are produced and one-third is shipped to other countries. The movement of most of these minerals, though, shows a rather remarkable concentration. For instance, manganese moves from three principal sources and converges at four or five consuming centers; chromite and tungsten move from two principal sources. The United States is more nearly self-sustaining in regard to mineral commodities as a whole than any 'other country on the globe; but the interests of conservation - call for an international viewpoint in the handling of our mineral resources., There is perhaps as much need of specializing in mineral output as there is of specializing in manufacturing. The thought that every country on the globe should be self-sustaining in regard to mineral supplies is of somewhat the same order as the thought that every family should produce all its own raw materials rather than take advantage of the more favorable conditions existing elsewhere and so specialize in human effort. Extension of international control of minerals seems to offer possibilities of loss and gain-loss through a considerable sacrifice of national trade .and a narrowing of the field for private initiative in trade; gain through the possibility of attaining certain ends which are attainable only by international agreement, such as an allocation of supplies which will be to the advantage of the greater number of nations rather than to the advantage of the few that are strong enough to dominate the situation. The interests of conservation clearly require international control. Moreover, the lesson of the war points to the necessity of overhauling old international understandings and machinery, even though such a task would encounter great difficulties, not the least of which lie in the persistence of human habits and inertia. Whether the time has come to establish a league of nations with economic control can be determined only by our individual and collective answers to the question whether we are willing to make the necessary economic sacrifices, individually and nationally, in the interest of world harmony. The mineral industry should fully understand that, with international control, efforts to promote export will need to be modified and curtailed; that expansion of our trade in many lines will mean equivalent loss of trade to other nations; that the almost universal conception that expansion of foreign trade is a meritorious aim and end in itself, without regard to its effect on other countries, will need revision.

Jan 3, 1919

Without having asked for it, the writer has apparently been drawn into the discussion regarding relative hoisting capacities which was started by Woodward Iron, egged on by Joe Haller of Cleveland-Cliffs [Mining Engineering, August p. 642] and Axel Kjelgaard [November p. 919], who took exception to Mr. Haller's remarks of tonnage hoisted and avers that they do better in Sweden. It does not appear to the writer that Mr. Haller was inclined to refer to the tonnage hoisted at Cleveland-Cliffs in a manner to imply that they claimed any hoisting record, but rather as a statement that they had hoisted a certain amount of ore during the year 1950. Mr. Haller has been in the mining game long enough to appreciate what Mr. Kjelgaard did not apparently take into consideration, that length of haul, shifts hoisted, nature of ore, method of loading and the many other factors which influence the hoisting cycle make a comparison of tonnages hoisted of two given mines almost an impossibility. Mr. Cheyette sent you .a copy of his letter to Bob Manegold relative to the capacities of the Orient #2 mine. There are several mines around the Country which constantly set up records about which little or nothing at all is ever heard. We cite the Snow Hill Coal Co. mine at Terre Haute, Ind., which has an automatic Nordberg hoist and which hoists 12 tons per trip or 700 tons per hr from 700 ft. This is a counter-weighted installation and a complete cycle is made every 62 seconds or 58 trips per hr. Another mine, The Potash Company of America mine at Carlsbad, N. Mex., has a Nordberg automatic hoist, hoisting eight tons per trip from 1150 ft on a one minute cycle. The materials hoisted in these two mines are ideal for automatic hoisting-they are free flowing so that no hang up is anticipated and hoisting is continuous. Multiplying out the above figures you will find that it is possible to hoist 11,000 tons in two shifts at Snow Hill or over 3 million tons in 300 days per year and over 2 million tons at Potash. Other mines have records which can be pointed to with pride. When a record for one year is established, it doesn't stand too long as here in America the ambition of all the men connected with the operation forces them on to larger tonnages. T. C. WIEDENHOEFER MANAGER MINE HOIST DEPARTMENT NORDBERG MANUFACTNRING CO. MILWAUKEE, WIS.

Jan 1, 1952

By C. E. Birchenall, R. H. Condit, M. J. Brabers

In the oxidation of pure iron above 700°C the overall rate is determined mainly by the rapid growth of wiistite, through which iron ions can diffuse rapidly.' Nickel added to the iron progressively decreases the stable range of composition of wustite.' When enough nickel is added to eliminate wiistite as a stable phase, the spinel is the fast growing phase. This investigation was undertaken to test the hypothesis that nickel substituting for iron in magnetite might decrease the rate of spinel growth by reducing the iron mobility. Nickel ferrite boules grown by the flame fusion process were purchased from the Linde Co. Chemical analysis gave an atomic ratio of iron to nickel of 2.88 and showed no other cations. They were cut into discs and ground to give flat, parallel faces. The experimental procedure employed was like that of Eisen and Birchenall in which the distribution of radioactivity diffused in from a vapor deposited surface layer was determined by counting the residual activity through a series of ground faces. The diffusivities were calculated in a manner consistent with the requirements discussed by Condit and BirchenallP The details will be given in connection with a more extensive spinel diffusion study now in progress. The results of the measurements are shown in the figure in comparison with earlier data on magnetite1 and zinc ferrite. The uncertainties arising from scatter in the activity vs distance relationship and uncertainties in the temperatures are shown by flags. Despite the scatter it is clear that substitution of a considerable part of the iron in magnetite by nickel, in this case about one third decreases the iron mobility substantially. sachs' determination of the distribution of iron and nickel in scales on iron-nickel alloys appears to show that nickel is less mobile than iron in the spinel layer. It is evident, therefore, that nickel plays several roles in reducing the oxidation rate of iron-nickel alloys. 1) It reduces progressively the stability range of wiistite. ' 2) It reduces progressively the stability range of the iron-nickel spinel phase in terms of the variation in cation to anion ratio.' 3) As shown in this investigation, it reduces the cation mobility in the spinel phase which is the faster growing phase in the absence of wiistite. The fe was obtained from the Oak Ridge National Laboratory. The research was supported by the Air Force Office of Scientific Research (ARDC) under contract number AF 18(600)-967.

Jan 1, 1961

SMALL things are customarily moulded in two ways (unless they have undercut parts which hold them in the moulds); that is in clay, or with natural or which artificial earthern powder made in halves in either wooden boxes or bronze frames. This also depends on whether the object is larger or smaller. Now if you wish to mould with moist clay, you must grease your relief with oil or pig fat; apply a dusting of charcoal, ashes, or cuttlebone on it; or gild or silver it dry with gold, silver, or tin foil. Then, first make with moist and somewhat firm clay a plate as, thick and large as can conveniently hold your relief, and carefully set the latter halfway into this and let it dry. Then, greasing or dusting it again, make the other half. When both are well dried, take out your relief and at the top make its gates and vents. If plastering is needed, do it. Finally, bake the halves, fit them together, and tie them well, as you wish, using the procedure that I taught you in the discussion of brass. But if one has to make a large quantity of works of one kind, he should for the sake of convenience use the method with powder [120] because it is short and requires less time and expense. Therefore if you wish to do this, you need to have several pairs of bronze frames or wooden boxes, higher than half the relief that you wish to mould, and of convenient length. On a flat board always keep half of one of these frames full of powder that has been slightly moistened for moulding, as I told you, so that by pressing with the ends of the fingers and with the hand it holds together as well as possible. Level it off with a cutting tool and when leveled put a flat board over it and turn it over. Turn it on to a dusting of ashes so that it will not stick, dust it on the other side, and remove the excess by blowing it off Then mould the thing that you wish to mould, pressing it halfway in once or twice, always taking it out and putting it back again. Then the other frame is fitted in its place and filled with earth by pressing and squeezing it carefully. Then it is leveled off on the outside with a sharp tool as you did with the other part, and then one of the parts of the frames is lifted up with the point of a knife or some other tool and,

Jan 1, 1942

By S. Suphi Yavasca, A. M. Gaudin

This paper is intended as a contribution to our knowledge of the mechanism of comminution and of the work of crushing. In a previous paper1 it was shown that with quartz comminution proceeds as follows: 1. The size distribution of broken fragments made by a single fracture is such that the new surface on each grade is the same. 2. Multiple fracturing results in a size distribution such that in the he sizes the surface per grade is the same in every grade; in coarse sizes the surface per grade decreases gradually with increasing size. In that paper it was mentioned that determinations on minerals other than quartz were in course of completion in order to establish the generality of these observations. In this paper, condensed data1 are presented for galena, pyrite and glass. Galena and pyrite are crystalline materials and glass is noncrystalline. Galena has excellent cubic cleavage. Pyrite, although cubical, does not have marked cleavage. Quartz, on which the original determinations were made, does not cleave and although crystalline (hexagonal) breaks conchoidally. Glass breaks much like quartz. It is apparent, therefore, that the minerals selected represent some range in character of the solid without covering all possible types. Glass Fifteen glass marbles were crushed individually in the pendulum crusher described in the preceding paper,' then subjected to careful screening for 30 min. Six sized fractions were selected and cleaned in a hot 0.12 N solution of hydrochloric acid, washed with distilled water and dried on a hot plate. This was followed by an examination with a binocular microscope, to remove foreign matters not eliminated in cleaning as well as to eliminate "compacts" of fine particles. These compacts are groups of he irag-ments that seem to be mechanically stuck together as a result of localized compacting during the comminution operation. The presence and the abundance of these compacts may be related to the amount and direction of the forces applied in different crushing devices. Since, properly, such compacts should be entirely eliminated in the sizing analyses, it is necessary to remove them to the last before making surface determinations on sized fractions. For example, with a — 28 + 35-mesh glass the surface areas of two samples, one cleaned with acid and under the binocular, the other only washed, were 102 and 172. cm' per gram, respectively. Examination of the samples under an Ultropak microscope showed that washing alone failed to remove the compacts and also that it fails to remove certain fine dusts attached to the particles. Cleaning with acid loosens the fine dusts and

Jan 1, 1947