Search Documents

By T. M. Morris, F. M. Lewis, W. C. Lay, Gordon M. Bell

Part I of this chapter is concerned with the description of and metallurgical data pertaining to the flotation circuits used in the London mill of the Tennessee Copper Co., at Copperhill, Tenn. The ores treated at the London mill are massive complex sulfides, in which pyrrhotite and pyrite are the predominant minerals. Other sulfides are chalcopyrite and sphalerite; magnetite is also of economic value. The approximate mineralogical analysis of the ore is shown in Table 1. [ ] The chalcopyrite and sphalerite are closely associated with pyrrhotite as shown by the tracings of micrographs (Fig. I), which are representative of the mill feed. Fig. la illustrates the type of locking between pyrrhotite and chalcopyrite; Fig. lb illustrates the way in which sphalerite is attached. Thesephotographs indicate that it is not practical to break all of these attachments. Hence, in order to produce concentrates with satisfactory grades and recoveries, most of the locked chalcopyrite particles must be recovered into the copper concentrate, and the locked sphalerite-pyrrhotite particles must be separated from the iron concentrate. A copper concentrate, a zinc concentrate, and an iron concentrate are made. Typical metallurgical results are tabulated in Table 2. HISTORICAL In 1922 the London mill started as a copper concentrator, with a capacity of 300 tpd, and in 1926 an additional flotation circuit was added to recover the iron sulfide remaining in the copper tailing. In 1927 a zinc flotation circuit was installed between the copper and the iron flotation circuits. This procedure was not satisfactory because the iron recovery was low, due to the

Jan 1, 1962

By L. A. Mekler

THE recirculating furnace is primarily a heating apparatus of the convection type in which the heat-absorbing surfaces are heated by a mixture of fresh products of combustion and a portion of the combustion gases that have already given off a part of their heat in their previous passage over the heat-absorbing surfaces. In its basic conception, the recirculating furnace can be considered as a closed thermal system in which the heat-absorbing surfaces are .constantly swept by a fixed quantity of products of combustion at a given initial temperature with the gases being constantly returned to the furnace and reheated before they again enter the heating zone. Gases equal in amount to that produced by the fuel burned to reheat the circulating gases are constantly ejected from the system to the stack. The recirculating furnace is the most suitable apparatus for heating by convection where low furnace temperatures must be maintained and where only a small portion of the available heat is taken out of the gases, particularly where the maximum allowable furnace temperature is low and where the final temperature of the gases is only a few hundred degrees below their initial temperature. In such cases, recirculation not only provides a method of reducing the rather high combustion temperatures of the fuel when burned without a large amount of excess air, but, by returning to the furnace the heat content of the gases at their final temperature, recovers a large portion of heat that otherwise would have been lost through the stack.

Jan 1, 1928

By George F. Becker

Complexity of Rock-Fractures.—The strains to which rocks have been subjected are manifestly very complex, and it is entirely safe to presume that every possible mode of deformation and rupture is exemplified. The most superficial inspection of any ordinary mountain region is sufficient to assure the observer that the rocks have been pressed, stretched, bent, buckled, twisted, and shorn. The study of torsional rupture cannot fail, therefore, to throw light on geological phenomena. The question is how areas which have been broken in this manner are to be distinguished from those which have yielded to other systems of forces. Phenomena of Joints.—It is well known that a large part of the more homogeneous rocks and some very heterogeneous rocks are intersected by partings often ailed joints. These partings are frequently flat surfaces even when seen in very large exposures, but are sometimes surfaces of moderate, single, or double curvature. Joint, usually occur in groups, in each of which the several partings are parallel to one another, and several such groups often intersect the same rock-mass. In such cases the different systems make large angles with one another. Nearly all students of the subject of jointing have reached the conclusion that joints are faulted surfaces, the dislocations usually being of small amplitude; and this conclusion receives abundant support from the study of thin sections under the microscope. It has thus been shown that much even of what would be regarded in hand specimens as mere slaty cleavage

Jan 1, 1895

By J. J. Bowman, E. H. Dix

A LACK of experimental data illustrating the effect of composition, particularly in respect to impurities, on the mechanical properties and corrosion resistance of aluminum-alloy die castings induced the authors and their associates to undertake a limited study of these relations. A number of commercial alloys and several experimental variations of a commercial alloy were used for the investigation. Mechanical property, growth, steam, paraffin, salt spray and atmospheric exposure tests were employed. This paper deals with the more accelerated tests and the results they have produced. It is concluded that a high-silicon alloy with all impurities except iron strictly limited to small amounts will develop an excellent resistance to corrosion and retain satisfactory mechanical properties and casting characteristics. As a direct result of this investigation an alloy of this character with superior corrosion resistance is now available commercially. In general, copper increases the strength and decreases the elongation and corrosion resistance. Tin reduces the mechanical properties and the resistance to corrosion. Iron reduces the elongation and, if excessively high, may adversely affect the tensile strength. Even excessively high iron contents do not affect the corrosion resistance, which is fortunate for the die caster as it is this element that is the most difficult to control. Nickel and zinc in limited amounts do not seem to affect the properties or corrosion resistance of at least the high-silicon alloy. Growth tests have confirmed the previous common belief that dimensional changes under either dry or wet conditions at 100° C. are too small to be of practical importance.

Jan 1, 1935

By E. C. Lee

The safety of mine workers has received more attention from both State and Federal law-making bodies than any other industry, a fact that shows clearly the hazardous nature of the industry. The last, but by no means the least, of the measures adopted for the protection of mine workers, is workmen's compensation legislation. This is proving to be a powerful instrument for greater safety in the industries, from the fact that special stress is laid not on how the accident happened or who may have been responsible for it, but on how badly the employee is hurt by it. The injured person does not have to employ lawyers to prove his case, because- the mere fact of his employment is proof of his right to compensation. The immediate effect of such legislation is the certainty confronting the mine operator that he must. pay out large sums for every accident, regardless of its cause, thus adding materially to the cost of the production of his coal. his fact furnished to the operator the strongest incentive to reduce the causes of accidents; not that the operator has ever lacked reasonable consideration for the welfare of his employees and a proper humane interest in their safety, but his engrossmentin earning his daily livelihood has been so great that he has not felt that he had the time to devote to the safety of the operation. This time he must now find because of the actual cash value of the prevention of accidents in his mines. This agency alone proved inadequate to bring about a material improvement because operators have always been willing enough to improve safety conditions when possible to do so within reasonable limits of their financial ability. The requirement in the Workmen's Compensation Laws of several of the States, that the mine operator shall insure as a guarantee of his ability to meet his compensation obligations, has furnished the needed incentive, moral and financial, necessary to the prompt and effective dissemination of a more general knowledge of the causes and

Jan 1, 1918

By T. L. McCall

This is a continuation of the paper on bumps presented by the late Mr. Herd in February, 1929. The seam worked consists of bituminous coal, 9 ft. thick, pitching 20°, and now under a depth of cover of 2800 to 3200 ft. Full particulars are given of two bumps that happened in November, 1931, with an interval of only 9 hr. between them. The first was a "district" bump affecting an area of 1000 ft. on the strike by 700 ft. on the dip and rise, beginning at a distance of 1000 ft. from the long-wall faces. The second, which caused much greater damage, was localized to two levels 200 ft. apart, in the area left undisturbed by the first bump next to the longwall faces. Observation stations had been established in the workings in 1931 and definite records were obtained on the flow of coal taking place from the edge of large pillars developed for retreating work, into the open roadways. The records also gave evidence that "advance weighting" or "underdraw " was affecting the coal at an average distance of 260 ft. in advance of the longwall faces. The author propounds the theory that the sandstone bed varying from 0 to 75 ft. in thickness and lying 14 ft. above the coal acts as a slab in distributing the superincumbent weight. The weight is thereby concentrated on the pillars in advance of the longwall faces and this load, in conjunction with a pavement strong enough to resist the reaction, leads to overstressing the pillars, which finally collapse suddenly, thus giving rise to this particular type of low side bump. The overlying sandstone bed, which is apparently a condition common to all coal mines in which bumps occur, is not necessarily a massive bed, as the thickness of this bed at Springhill in the area that has experienced these severe low side bumps is only 25 to 31 feet. A list of 43 minor bumps occurring in the past 2½ years is appended

Jan 1, 1934

By Julius Pohlman

Considering the truly wonderful natural resources of the United States, and the variety and extent of uses for hydraulic cement at the present day, it seems strange that the manufacture of the artificial product called Portland cement has not been introduced here. Possibly the reason may be we have in different States of the Union rock deposits from which a cement can be obtained that is as good, and some claim even better, because of a more uniform quality, than the English product after it has been subjected to transportation across the ocean. One of these natural cement-rock deposits is found in the northern part of the city of Buffalo, and its manufacture has been carried on successfully for the past eleven years by the Buffalo Cement co., Mr. L. J. Bennett, President. The quarries cover an area of about two hundred acres, of which only twenty-five acres have been exhausted up to date; and the supply is assured for years to come. One acre yields on an average 80,000 barrels of cement; hence 12,000,000 barrels is a low estimate of what these quarries will yield before they are exhausted. According to the Geology of New York this cement-rock deposit is called the Water-Lime group, and forms in this section the uppermost member of the Upper Silurian. Its outcrop can be traced along the base of the second limestone terrace of Western New York, but at Buffalo a very large part of the overlying Corniferous limestone has been removed by natural agencies, leaving only about eight feet (six feet of rock and two feet of clay) on the top of the cement-rock, and thus furnishing the conditions for successful quarrying at a minimum expense. This rock is really an impure limestone, a mixture, as it were, of the underlying shales of the Onondaga Salt group with the overlying

Jan 1, 1889

By William F. Blake

In September I contributed an article upon Columbite in the Black Hills of Dakota to the American Journal of Science. I had not at that time seen the paper by Professor Charles A. Schaeffer, of Cornell University, upon the occurrence of tautalite in the same region," or I would have gladly made reference to it. His analysis, proving the entire thence of columbic acid, shows that the specimen he analyzed, at least, should be called tantalite, and not columbite, if the distinction between these two closely related species is to be maintained. It is hard to say where the line is to be drawn, in such cases, between two minerals, when the specific characters and the composition are so nearly the same. If the name is to be determined by the relative amounts of tantalic and columbic acids, what shall we call the mineral when these acids are present in nearly equal quantities? Preference was given in this case to the name columbite, for the reason that the specific gravity, as ascertained by the ordinary scales at command, was nearer 6 than 7. As Professor Schaeffer had only one fragment by post, while I had an abundance from many places, it may yet be found that columbic acid predominates in some of the specimens. I therefore use the name columbite or tantalite indifferently. With this explanation I proceed to give a few observations upon the occurrence of the mineral with the tin-ore of the Black Hills. There are two localities, especially, where the mineral is found in the same dike or vein as the cassiterite: 1. at the Etta mine; 2. at the Bob Ingersoll claim. At the Etta it occurs in close association with albite and feldspar in crystals from one to four or five inches broad, and from one-quarter of an inch to three inches thick. It is not in contact with or mingled with the cassiterite, and each call be

Jan 1, 1885

By E. P. Jennings

These unique copper-deposits occur on the top of the Kaibab Plateau, in Cocouino county, Arizona, and extend from the northern edge of the Grand Cañon of the Colorado river to near the Utah State line. The best-developed deposits are near Jacobs Lake, 30 miles south of the Utah line, where they are 16 ft. thick, of unknown width, and are more or less continuous for 5 miles. From Jacobs Lake to the edge of the Grand Cañon, a distance of 40 miles, outcrops of ore have been found, but no explorations have been made except those of wandering cowboys and hunters. The Kaibab Plateau, the highest of the Colorado river plateaus, is a great uplift, about 90 miles long from north to south, and from 10 to 20 miles wide from east to west. Its southern face is the Grand Cañon; its western boundary a N—S. fault plane, which separates it from the Eanab Plateau, lying 1,500 ft. below. Its eastern edge is a monocline which brings the horizontal beds of the high plateau to the level of the plateaucountry of eastern Utah. The elevation of the plateau near the Colorado river is over 8,000 ft., and about 6,000 ft. at the Utah line. Its structure, as shown by the western fault, consists of about 500 ft. of Aubrey limestones underlain by 1,000 ft. of red sandstones. The limestone is the upper member of the Carboniferous, and is overlaid by the marls and shales of the Permian, 25 miles to the north on the Kanab Plateau. At the town of Kanab, near the Utah line, the Permian strata pass under the magnificent redsandstone cliffs of the Triassic, that rise to heights of 1,000 ft. above the desert. The Grand Cañon exposes a section a mile deep at the southern end of the plateau, showing all the formations from the Archean to the top of the Carboniferous.

Jan 1, 1904

By John Hall

THE recently announced run of three years, nine months and eleven days made by a. crucible steel melting furnace of the Columbia Tool Steel Co., which is claimed as a. world's record, brings forcibly to our attention the great improvements that have been made in the design, construction and operation of the Siemen's regenerative crucible- melting furnace since its introduction in this country. Credit for this advance should be given to the furnace designer, the manufacturer of refractories, and the operators of the furnaces, whose persistent efforts and intelligent co-operation in attacking the problem have resulted so satisfactorily. There are three factors that determine the life of a crucible furnace, or any other furnace for that matter : Design, nature of refractories and conditions of operation; (including the nature of steel melted) and to some extent these factors are interdependent. Thus, for instance, if a crucible furnace is to lie operated single turn and allowed to cool off considerably at night, in order to save fuel, the use of clay-brick melting holes may be advisable, since silica brick is not well adapted to endure rep eated heating and cooling. But the total life of a clay-brick melting hole is necessarily short. Again, if local conditions such as danger of flood make necessary the building of the furnace largely above ground, so that the radiation of beat is promoted, the cooling down of the furnace over the week ends, when no steel is melted, will be considerable-and the contraction of the furnace that results tends to wrack it to pieces. The character of the metal being melted affects the life of the furnace to a great extent. Low-carbon steels and steels made from iron and charcoal require higher temperatures and much longer melting tune than high-carbon steel or steel made largely from scrap; the life of the furnace will be shorter, and the number of heats melted will be much less, when such materials are melted.

Jan 9, 1913

By Eliot Blackwelder

For the purposes of this paper, the boundaries of China and Siberia will be taken as they stood about 1907. Except in the Caspian region, it is doubtful if all the oil ever produced in these countries would equal one day's flow of a good Texas well. Considering the vastness of the regions and the variety of strata, it seems strange that these two countries should have made so small a showing in the petroleum industry. No doubt the condition is caused partly by lack of prospecting and of modern methods of development; in larger measure, however, it is evidently because of unfavorable geological conditions over nearly all of east-central and northern Asia. CHINA The known oil occurrences in China are very few. For many years, perhaps a barrel a day has been obtained by primitive methods from wells near the city of Yenchang in the northwestern province of Shensi. A like amount was obtained from wells bored for salt water in the vicinity of Kiating in southwestern Szechwan. The little oil was separated from salt water by allowing it to stand in jars. The salt wells yield also considerable natural gas, which is used to evaporate the salt and also for domestic purposes. There is evidence that wells were bored in this part of China before the third century. It is said that more than 1200 wells have been sunk in that district to depths of 1600 to 2000 ft. (485 to 610 m.) in connection with the salt industry. The scarcity of petroleum in China may be ascribed to three general geologic conditions: First, China contains practically no marine sediments of Mesozoic or Cenozoic age; second, the Paleozoic sediments are not for the most part of the types that generally contribute petroleum; third, the rocks of nearly all ages have been strongly folded, faulted, and more or less intruded by igneous rocks in all parts of China except certain areas in the west and northwest.

Jan 7, 1922

By T. W. Guy

THE increased moisture due to water¬spraying for coal dust control is of interest even for mines from which the coal is to be wet-washed before screening, because in many cases wet coal dust materially decreases the loading efficiency of men an equipment at the faces. It also causes serious increase in the normal wear and deterioration of all equipment with which it comes in contact. It is important to the consumer if it increases his as-receive moisture. No attempt will be made in this paper t cover the entire subject of water-spraying of coal for dust control. It will be confine to discussion and data on (r) percentages c dust in bituminous coals, (2) moisture increases due to spraying for dust control in mines or plants by methods which have proven satisfactory for periods of one to five or more years, and (3) a few suggestions for research. SIZE AND PERCENTAGE OF COAL DUST The U. S. Bureau of Mines1 classifies a coal dust all bituminous coal passing 20-mesh sieve (0.0328 in. square opening; The percentage of such dust to be found is ROM coal, of course, varies widely wit. the characteristics of the seam, and with the methods used in the mining and in the preparation of the coal. ROM screen analyses of 12 U. S. coals selected at random from personal files given in Table I show: A few other screen analyses examined indicating 40 pct or more of 2o-mesh X o dust in 3/8 in. X o-sizes were not included because of uncertainty that they were representative. The number of results in Table I is not sufficient to give a reliable estimate of the average, or of the range to be expected, but it indicates that in every case the coal dust is a relatively large percentage of the total ROM coal, and, of course, a progressively larger percentage of resultants as the larger sizes are separated for marketing.

Jan 1, 1948

By Alexander Field

IN THE light of the experimental data on equilibrium for the reaction C + FeO = Fe + CO in molten steel recently obtained by Kinzel and I Egan,1 it is necessary to revise current theories regarding the nature of equilibrium between carbon and FeO in the basic open-hearth furnace. According to the measurements of these investigators the equilibrium constant m for the above reaction for a pressure of dissolved CO equal to 1 atm. is equal to 0.0005 at 1550° C., when concentrations of carbon and. FeO are expressed in percentages by weight. Their work also shows that, with the pressure of CO fixed at 1 atm., not only is the product of carbon and FeO constant, but carbon and FeO are each independently constant-a circumstance which might have been predicted from theoretical considerations. At 1550° C., carbon is constant at about 0.025 per cent. and FeO at about 0.020 per cent., with the pressure of dissolved -CO equal to 1 atm., the product of these two constants being equal to the originally mentioned constant of 0.0005. Available data on the dissolved FeO content of samples taken from the metal bath at practical slag-metal equilibrium prove that this FeO content is determined solely by temperature and the effective FeO content of the slag. The distribution constant r at 1550° C., as determined by Herty, Gaines, Larsen, Simkins, Geruso and Watkins2 is equal to 0.0086. A slag would have to contain 0.020/0.0086 = 2.3 per cent. effective FeO or less in order to prevent the metal from containing more dissolved FeO than that required for equilibrium with CO at 1 atm. pressure. Such low percentages of FeO are never found in basic open-hearth slags at the completion of a heat when rate of carbon drop has become practi-

Jan 1, 1930

By Nicholas T. Camicia

A career in the coal mining industry today offers students one of the most interesting and challenging opportunities available in the industrialized world. As reserves of other fossil fuels dwindle in face of the world's demand for energy, it has become apparent that coal, once the king of energy sources, must be relied upon again as the major fuel for powering industrial growth in developed and developing nations. Centuries of coal supplies lie beneath the earth's surface, assuring the world of a steady, plentiful supply of energy until science and technology can produce a way to harness and efficiently use renewable sources, such as solar. The need to increase our use of coal during the last two decades of the 20th century is reason enough to believe that the future growth of the coal industry is assured. A major impediment to that growth might be backward national public policies that could restrict the full utilization of our coal reserves. These policies could result from overregulation and a failure of the public to recognize that coal use, with proper techno- logical safeguards, is compatible with our society's environmental-quality objectives. Communication of this problem and its solution is a major undertaking of the coal industry in the 1980s. At the end of the 1970s, the American coal industry was producing approximately 635 Mt/a (700 million stpy) of coal. To meet the nation's projected energy needs by 1985, the annual tonnage must be doubled. A similar scenario is predicted for the rest of the world. Such growth in the modern international business world will require huge additional amounts of capital, equipment, and people who know how to wisely raise and apply the capital; use the equipment productively; and deal with the many community, public, and governmental problems such expansion will create. Whether a student's interest is in actual mining operations, business administration, engineering, finance, law, industrial relations, marketing

Jan 1, 1981

By R. W. Raymond

The various modifications of the art of photography have become within the last few years the indispensable allies of every art and science. But, before the introduction of the process which is the subject of this paper, there was, so far as I am aware, no satisfactory means by which certain photographic negatives could be made to yield, without the intervention of the skilled draughtsman, electrotypes suitable for surface-printing. I refer to negatives taken from originals, such as natural objects, or or lithographs, in which the lights and shadows are not represented exclusively by lines and dots, such as can be photo-engraved. The greater usefulness to engineers and manufacturers of electrotypes as compared with lithographs is evident. The electrotypes can be kept indefinitely and used in the production of many thousand copies. They can be duplicated at trifling cost. They can be placed for printing together with the " forms " of type, or included in these, upon an ordinary press. Finally, they are cheap, when made mechanically from a suitable original. Various methods have been adopted for the preparation of such a secondary original (as it might be called) in cases where the first original is unsuitable for photo-engraving. Thus, for instance, portraits have been produced in electrotype from ordinary photographs as follows: A large negative is made of the original (say a carle de visite of a person deceased), and a proof taken, but not " fixed." Over this proof a skilled artist draws the portrait with a pen, producing a picture which resembles a line-engraving. The photographic proof, which has served merely to guide the artist, is now obliterated, and the pen-and-ink drawing is photo-engraved. Electrotypes thus produced often retain the likeness in a wonderful degree, and give spirited and satisfactory pictures. 1 may instance, as examples, which many will recollect, the portraits of our deceased members,

Jan 1, 1887

By C. E. Van Orstrand

AN intrusive body is a mass of igneous rock that has migrated upward, presumably from great depths. Great variations in form, composition and depth of burial occur. It is not proposed in this paper to go into all of the details of the problem. Instead, it will be assumed here that the intrusive has the form and characteristics represented in Fig. I. According to W. H. Emmons,1 minerals are not deposited in appreciable quantities below the "dead line." Important amounts of ores of virtually all metals may be found around summit cupolas, but only gold, copper and zinc (in limited quantities) are usually associated with trough cupolas. Most students of ore deposits agree that temperature changes are largely instrumental in precipitating many ores in the "hood" and that the difference in temperature between the intrusive and that of the country rock may be the chief factor in determining the mineralogy of a deposit. A problem then of some interest is to correlate the principal physical features of the intrusive with the phenomena of heat conduction as evidenced by the cooling curves and the isothermal surfaces. MATHEMATICAL THEORY In order to show the possible application of heat conduction to the interpretation of the processes of metalliferous deposition associated with intrusives, it will be assumed that the intrusive is a large parallelopiped of dimensions, 2l, 2m, 2n. The equation that represents the flow of heat from the parallelopiped into country rock (v = o, t = o), which has the same thermal properties as the intrusive, is2,3 [ ] In this equation, the origin, x = o, y = o, z = o, is at the center of the parallelopiped. 'v = temperature at point x, y, z, time t. vo = initial temperature throughout the intrusive, t = o. K = coefficient of thermal diffusivity. a, ß, ? are variables of integration. Put n = m in Eq. I, and we have [ ]

Jan 1, 1944

By Joseph P. Hodgson

Since about 70 per cent. of the total cost of mining is due to underground work which is out of sight, it is essential that expenditures should be made here to the best advantage. A great many mistakes have been made which were expensive, but perhaps these have not even been detected by mine owners. In the future these may be minimized to some extent, especially if there is cooperative effort on the part of each employee. I have been interested in this subject for some years and have tried to deduce principles and methods. These have proved highly advantageous and may also be of help to others. Some corporations, like the United States Steel, and the Cleveland-Cliffs Iron Co., have done a great deal in this field by having stated meetings of their organizations, with the view to interchanging ideas among their men and educating them along the lines of concerted effort. Since no man knows all about the various branches of mining, it is advisable that frequent meetings of the operating department be held for the interchange of ideas and that all members of the organization have an opportunity to express themselves on the various subjects. It has often been found that in discussions between heads of departments, foremen and bosses, many valuable suggestions may be obtained which promote the best interests of the company. The method regarded as the most conducive to cooperative effort, and pursued by the organization, is to analyze and develop the different phases of various mining subjects at regular meetings. Nine Foremen's Dinners In the latter half of 1912, the Copper Queen Consolidated Mining Go. gave monthly dinners to the men in the operating departments. Those who attended were superintendents, foremen, shift bosses, engineers, geologists, and heads of all departments, making a total of about 75 men. After the dinner, lectures were given on subjects which pre-

Jan 1, 1917

By H. C. Kenny

The annealing or softening temperature of cold-worked copper is appreciably increased by almost unbelievably small amounts of silver. As indicated by some data in this paper, the softening temperature of high-conductivity, tough-pitch copper may be increased from 200" to 350" C. by the addition of only 15 oz. per ton (0.052 per cent) of that element. Because it has this higher annealing temperature as compared with the silver-free metal, silver-bearing copper finds considerable use in industry. For example, when hard-rolled copper is used in operations that involve soldering or tinning, silver-bearing copper insures against loss of strength, whereas silver-free copper becomes "dead soft." Yet—though several investigators, beginning with Caesar and Gernerl in 1916, have shown that small amounts of silver do definitely raise the softening temperature of copper—data are lacking on the problem: What is the specific influence of different amounts of silver on this temperature? It was to help in filling this gap in the knowledge of what might be termed "alloy coppers" that the data given herein were obtained. The softening of cold-worked copper depends, of course, on a number of factors, of which the composition of the material is only one. Other highly important factors are the degree to which the material is cold-worked and the time it is held at the annealing temperature. The method of cold working and the grain size of the metal produced are also significant. All these variables were taken into account in the investigation reported here, and the influence of silver on the electrical conductivity and on the working was also considered. The coppers used in the softening tests were Lake coppers melted and cast by the Calumet and Hecla Consolidated Copper Co. The ires were fabricated by the Roebling Wire Co. and the sheets were rolled at the Battelle Memorial Institute. Partial analyses of some of the coppers are listed in Table 1, with their electrical conductivities.

Jan 1, 1934

By L. W. Bahney

The photograph, Fig. 1, shows the apparatus a little less than half size, consisting of a filtering-flask fitted with rubber stopper through which passes a bent glass tube, and an extraction-thimble fitted with rubber stopper through which passes a glass tube of 0.25-inch bore. Both tubes are connected by a short piece of rubber tubing. A section of a thimble is shown in the photograph ; the tube extends to within & in. of the tapered end. The object of using the thimble is to remove the acid from the beaker after all the copper has been precipitated. Time is saved, the copper is not exposed to the acid alone, and there are none of the losses attending ordinary filtration. I have accomplished these results by means of a piece of perforated platinum fastened in the end of a (0.25-in. bore glass tube and a filter-mat of asbestos, but after my supply of proper length fiber became exhausted I could not replenish it even after purchasing 14 lots from four different dealers. The above apparatus may be used to remove at least seven-eighths of a supernatant liquid from a settled precipitate without disturbing the latter. The application of the thimble is best shown by partly outlining the assay for copper, as follows: Dilute the acid solution of copper and other sulphates to 150 cc. in a 200-cc. Jena beaker, place on a hot plate, add 2 drops of concentrated HCl, then place a strip of aluminum in the beaker (this may be bent or straight, as desired). Connect the apparatus, as shown in Pig. 1, with a filter-pump having a strong suction. When the copper is precipitated, remove the beaker from the hot plate and insert the extraction-thimble alongside the strip of aluminum. The acid solution will be drawn through the porous tube. Wash the upper end of the aluminum strip with a jet of hot water, wash down the sides of

Jan 1, 1913

By Jan Wolski

Today's rapidly shrinking world requires a common language of measurements, a consistent system which could be used by everyone. The S.I. system of units is generally accepted as such and is already in use by a great majority of nations in the world. The change to S.I. units is also slowly taking place in U.S. engineering practice. The transition period is difficult and long because it takes time to get familiar with the new system, to start "feeling" values in new units. Instruments, formulas, computer programs, survey grids, etc. have to be converted or exchanged. The transition period should be used not only for substitution of units, but also for rationalization of presently used calculation methods. This paper examines the major parameters of mine ventilation from the above point of view and discusses a system which is much simpler and more consistent than the American Unit System still in use in the United States. In October 1979, the Society of Mining Engineers of AIME decided to introduce the S.I. unit system in all its publications including the periodical "Mining Engineering", and since February 1980 the system has been used consistently, not only in SME publications but in all conferences and meetings organized by this Society. The authors have no intention of explaining the details of the S.I. system in general. Any reader can find this information in many available publications and conversion tables, and in particular in the ASTM Standard for Metric Practice, E380-79. A comparison is made between various units used in mine ventilation from the past and those presently in use. This will allow an easy translation from one system to another, important when reading publications from abroad. S.I. and customary U.S. formulae are shown side by side for easier visualization of similarities and differences. Recommendations for the necessary steps in order to switch from American to S.I. units conclude the paper.

Jan 1, 1982