Search Documents

By R. M. Hardgrove

Pulverized coal was first used for firing cement kilns about 45 years ago, with such success that it has continued in general use. Based on cost, pulverized coal is usually the most economical fuel. In some localities natural gas or oil is cheaper, but 85.5 per cent of all cement kilns at present are fired with pulverized coal. The pulverized-coal flame is well suited to kiln conditions. Its soft, luminous nature gives it a high radiating property and the length of the flame can be readily varied to suit conditions in a kiln of any length. Ash and slag cause most of the dificulties incident to the burning of coal. In a. cement kiln, however, the ash, being similar in composition to the raw mix and being deposited uniformly in the mix and clinker, occasions no difficulty as long as it remains constant in quality and quantity. Until 6 years ago almost all cement kilns using pulverized coal employed the bin system. The coal was dried and pulverizeti in a separate plant and delivered into a bin at the kiln. Thus the bin system requires driers, storage-type pulverizers, conveying systems, individual kiln bins, pulverized-coal feeders and primary air fans. The direct-fired system requires only a pulverizer and a blower. Fig. I shows typical plants. The first installations of direct-fired pulverizers were of the impact type but fineness of pulverization was both inadequate and variable. About 1927 a few direct-fired installations employing tube-type pulverizers were made, which were much more satisfactory. As more efficient pulverizers were developed from 1934 on, equipment for direct firing was installed at a large number of plants, until now 196 of about 900 kilns in use in the United States are direct-fired. Most of these replaced antiquated bin systems. Process of Burning Cement Clinkers The process of burning cement clinkers is fundamentally one of heat transfer. In boilers and other heat-exchange apparatus the area of the surface receiving heat from the gases is the best unit for comparing output, This seems to be equally true for kilns. The inside kiln surface is the heat-receiving surface and its area is used as the unit of kiln size in the following comparisons. Heat input is based on British thermal units in the fuel. E. G. Bailey,' in his work on boiler-furnace heat absorption, has used the unit "B.t.u. available." This is the practical calorific power of the fuel, plus the heat in the air used for combustion. In other words, it is the heat available for useful work in the furnace or kiln. The unit of kiln output is barrels per hour. The composition of the raw mix, the percentage of water in the slurry of wet plants and hardness of burning all affect the output. These conditions, however, are hard to evaluate and probably have less effect on the output than irregularities of raw feed and clinker discharge and inexpert control of combustion. Wet vs. Dry Plants The study presented here covers 88 plantsl of which 41 are wet and 47 dry. Of

Jan 1, 1942

By T. S. Plaskett

A striated structure perpendicular to the growth axis was observed by the copper-decoration tech-nique in dislocation-free, .float-zoned silicon crystals. The striations, which were spaced about 100 p apart, fitted the relationship d = f/u , where d is the spacing, f is the growth rate, and u is the crystal rotation rate. Each stria was resolved into an UNDOPED silicon crystals pulled from quartz crucibles by the Czochralski technique usually exhibit a striated structure perpendicular to the growth axis.'-' This structure has been attributed to oxygen segregation, with the oxygen being introduced from the quartz crucible. If the crucible is rotated, the level of oxygen contamination has been reported as high as 10° atoms per cu cm.10 These striations are similar to solute striations commonly observed in doped Czochralski-grown crystals. The periodic nature of the striations is caused by a periodic variation in the growth rate",12 which is attributed mainly to thermal gradients in the melt.13 A finer striated structure14 attributed to constitutional supercooling is sometimes observed between the coarse striae. The oxygen striations have been observed by infrared transmission techniques,' by the copper-decoration technique,' by X-ray diffraction microscopy,6-8 and by 9 p absorption measurements3 on crystals pulled from the melt both with and without dislocations. In this investigation float-zoned dislocation-free crystals were examined by the copper-decoration technique. The level of oxygen for float-zone material is less than 1016 atoms per cu cm the lower limit of detection by 9 p absorption measurement. EXPERIMENTAL TECHNIQUE The crystals were grown by the float-zone process with the rf heating coil outside of the quartz envelope containing the silicon. All float zoning was done under an atmosphere of purified helium. The Dash technique15 was used to grow the crystal dislocation-free. This involves growing the crystal initially with a diameter between 2 and 3 mm and at array of starlike precipitates of copper. The strucLure was not .found at the surface tor a depth of about 1.5 mm, or in a region of similar width ahead of a dislocation network. The structure is postulated to consist of vacancy clusterings or dislocation loops. very rapid rates, about 20 mm per min, for a distance of about 3 cm. The diameter of the crystal is then increased to the diameter of the source of silicon, which in this case was about 19 mm. Because of the arrangement of the apparatus, the zone was passed downward rather than upward, contrary to the standard float-zoning practice. Also, the source was rotated rather than the seed. ziegler17 has made dislocation-free crystals by a similar technique but has passed the zone upwards. The starting material was zone-refined and had a p-type resistivity of 150 ohm-cm. The major impurity was boron; the total impurity excluding the boron was reported by the supplier (Dow-Corning) to be typically less than 2 x 1013 atoms per cu cm. The crystals were examined by the Dash copper-decoration technique18'19—a method in which about 10" atoms per cu cm of copper are diffused at a temperature between 900" and 1000°C into silicon which is then quenched to room temperature. On quenching, the copper precipitates on crystalline defects which are then visible when viewed by transmission infrared microscopy. The photomicrographs shown were taken either of the infrared image tube screen or directly on infrared film. All sections prior to decorating were chemically polished and, for some sections, given a sirtlZ0 dislocation etch-pit examination. After decorating, the samples were mechanically polished. RESULTS A photomicrograph, taken in transmission of a decorated cross section, is shown in Fig. 1. The portion of the section shown is near the surface of the crystal. The entire cross section showed no dislocation etch pits after being given a Sirtl etch treatment. It is seen that the copper precipitated randomly. Each precipitate, as has been reported by others, was found to have a starlike structure.

Jan 1, 1965

By Robert L. Thoms, Richard M. Gehle

Hydraulic fracturing is of considerable interest as a possible release mechanism during operation of storage caverns in salt formations. However, field data are lacking on fluid pressures required to initiate and propagate fractures over a range of depth in U.S. salt domes. A currently active research project is outlined which has the objectives of gathering field data on hydrofracture gradients in inland and coastal domes of the Gulf Coast. A wireline minifracturing system with downhole microprocessor controls is briefly described.

Jan 1, 1985

By Manfred Schmellenkamp

During the lust half-dozen years, longwall mining has taken on a new look, much of which is due to the introduction of self-advancing roof supports from Europe. Here is a report on two longwall operations, one which started up in 1956, the other in 1962. It is a story of manually set, friction- type props us, the new European type; the story of an 18-ton per man-shift operation us one of 50 tons per man-shift.

Jan 6, 1963

By John F. Slonaker, Joseph W. Leonard

This note is a review of current research intended to increase the utilization of coal ash. Due to the magnitude of the fly-ash research program, some projects may be inadvertently omitted. Field research on fly-ash for use as an agricultural fertilizer is being monitored at Virginia Polytechnic Institute and State University. This research is directed at determining the plant nutrients that are available in fly ash as well as the quantities of fly ash that can be applied to agricultural soil.

Jan 1, 1975

By R. T. Hukki

BALL wear as observed in grinding installations is the combined result of mechanical wear and corrosion. Corrosion should be a linear function of the ball surface available. Ball corrosion, however, has been studied so little that its effect, although of great importance, cannot be included in the analyses given here. In a separate paper' it is shown that [ ] Exponent m is the slope of a straight line on logarithmic paper relating mill speed (on the abscissa) and mill capacity (on the ordinate).

Jan 6, 1954

By W. D. Haentjens, A. P. Pipilen, M. Weintraub, A. A. Orning

W. D. Haentjens (Barrett, Haentjens and Co., Hazleton, Pa.) — The authors are to be complimented on undertaking a project which has little available experimental data. There are so many variables in the hydraulic transport of solid materials that it is difficult to correlate the experimental information from one series of tests into usable data involving other materials or even similar materials but of different size consists. The friction data is of particular interest to those involved in pipeline design. Most such pipelines, however, involve portions which are not level and the effect of sloping or vertical lines might also be considered in extensions of this test work. Pump manufacturers are concerned about criticism resulting from the stated amount of degradation occurring in a pump. The amount of degradation is affected somewhat by pump design and this should be taken into consideration. The pump which was loaned for this work was a modification of a standard medium duty slurry pump. This modification was for maximum particle size, however if minimum degradation is the object, then other design changes would be indicated. Although there is a tendency to be less concerned with degradation in industrial applications, it is nevertheless an important factor in many uses and further studies should be made. In particular, the amount of degradation could possibly be segregated into more classifications, rather than charge some losses to the pump which apparently are occurring in other handling. It seems difficult to evaluate the degradation which occurs in handling the coal into the pump sump and in removing it from the line into the tank. Each handling, of course, contributes some degradation, as does the screening operation itself. These are all charged to the pump, or to the pipe line and pump together; and, although they may be small, they could possibly be evaluated. It is interesting to note the verification of the old rule of thumb of maximum particle size equal to approximately one-third of the pipe size. Our experience has shown size distribution to have an effect on the flow characteristics and if this data is available for the tests which were run, it would be interesting supplementary information. A. P. Pipilen, M. Weintraub and A. A. Orning (Authors' Reply) — In this paper the authors have attempted to outline some of the major factors affecting a rational design for a solids-liquid transport system. They are grateful to Mr. Haentjens for pointing out several other equally important considerations. Pump manufacturers, in general, should be complimented on the strides that have been made in decreasing particle degradation within the pump. Considerable research and a great deal of mathematical analysis is required before pump design in this field can become a science rather than an art, for each system requires a different set of compromises. As Mr. Haentjens indicates, maximum-particle-size handling capability may be inconsistent with minimum degradation; even more important, the rotor profile for the most efficient transfer of energy to the fluid may have to be compromised to reduce particle breakage, for, whenever particle density differs from fluid density, the two phases will have different trajectories. Some evidence of this geometric factor is provided by a cursoy analysis in the Bureau of Mines Report of Investigations now in preparation, where it is indicated that, for the pump used, degradation decreased when the tangential velocity was decreased and when the radial velocity was increased. This relation, itself, is probably a function of particle size and concentration. Some data on particle size distribution, as requested by Mr. Haentjens, will be provided in the Report of Investigations referred to above in addition to that already presented in Table II of the original paper. However, in the limited number of tests it is difficult to distinguish between cause and effect, for not only did the particle size distribution alter the flow characteristics, but, through the medium of degradation, the operating conditions rapidly altered the particle size distribution.

Jan 1, 1965

By D. L. Everhart

The search for new deposits raises two important questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? A review of the wide geological variety of recent uranium discoveries tells how these questions are being answered. SOONER or later intelligent exploration for uranium leads to these questions: Where did the metallic ions that formed the orebodies come from? What processes and geologic factors were involved in ore replacement? These matters, of course, make a big difference in how best to look for orebodies. Before these questions are discussed it might be well to point out other factors bearing on the subject. The whole business of uranium exploration is only a little over ten years old, participation by the public is only about six years old, and real interest and activity by more than a few large mining companies has arisen only in the past two or three years. Throughout this short period, uranium exploration has been affected by the unique influences of necessary security measures and by division of the overall job into individual projects by a large number of specialists in diverse fields. This has meant that a normal interchange of information on the nature of uranium deposits has really only just begun. Compared to the vast amount of published studies on iron, copper, lead, zinc, and gold deposits over the past 50 to 75 years, current knowledge of uranium deposits is in its infancy and much of the pertinent information is still scattered about in a number of unpublished sources. The volume of reports on all phases of uranium exploration is now beginning to mount at a remarkable rate, and geologists with widely varying specialized backgrounds in uranium geology are engaging in spirited debates over the origin of uranium and the relative importance of geologic controls of various deposits. One of the most interesting features of known uranium deposits of the world is the wide variation, see Table I, in character and geologic environment. It should be noted that many types became prominent during 1953. The davidite-bearing veins of Radium Hill, South Australia, are almost unique, although the same mineral occurs in a different kind of deposit in Mozambique. Recent studies indicate that brannerite disseminated in the granite near Cracker's Well, South Australia, may soon constitute uranium ore. Basalt has been added to the list of favorable host rocks in the Northern Territory of Australia. Basalt is also the host of the pitchblende veins of the Martin Lake deposit, Beaverlodge district, Saskatchewan. The truly remarkable rich and extensive Steen deposit near Moab, Utah, is of the uraninite-vanadium oxide type. Secondary hydrous uranium arsenates and phosphates constitute the uranium minerals in the disseminated deposits of the Wind River Basin, Wyo., a new district discovered in the summer of 1953. Uranium minerals in shales adjacent to fractures were newly reported in New Mexico and several other parts of the world during the year. The well-known important uraninite dissemination in the Rand conglomerates of South Africa has a counterpart, as discovered in the summer of 1953, in the Mississagi quartzite and conglomerate of the Blind River district, Ontario. Gunnar deposit of the Lake Athabaska district, Saskatchewan, consists of uraninite in both granite and sedimentary gneiss beneath a granite cap, and large new orebody of the Eldorado Co. in the same general area follows a preferred stratigraphic horizon in schists. Uranium is, generally speaking, a very soluble and ubiquitous element. It occurs in at least two valency states and for this reason is not easily tied down in natural solutions. As Gruner' has pointed out, it is probable that uranium starts in the hexava-lent state in nearly all solutions instrumental in its transfer. It is believed that under oxidizing conditions the uranium moves in solution as the uranyl ion, UO. In solutions ranging in pH from 1 to 5, the uranyl ion is most commonly in association with

Jan 1, 1955

By J. Kitagawa

INTRGDUCTION The Paragsha concentrator is the largest of Cerro de Pasco Corporation's base metal beneficiation plants operating in Peru. At present, this plant is treating an average of [ ]

Jan 1, 1970

By J. R. Johnson

ZIRCONIUM'S corrosion rate by reactor fuel solutions increases with increasing reactor power. It is believed that the protective oxide film is affected by radiation damage. Observations of the

Jan 1, 1959

By Oren C. Baptist, Carlon S. Land

Laboratory research has been conducted to evaluute the effect of clay hydration on the permeability to gas of water-sensitive reservoir sands. Samples of a .sandstone containing trace amounts of montmorillonite and a sample of montmorillonite were .studied in the laboratory to detertnine whether swelling or dispersion was the cause of permeability reduction in these samples. Heliuin, containing various amounts of water vapor, was used to hydrate the clay minerals and to determine the gas permeability at various stages of clay hydration. The amount of water adsorbed by the samples using this method is small. The nonwetting-phase permeability at higher water saturations war investigated by saturating the with water and measuring the permeability to humid helium while decreasing the water saturation, Relative-permeability curves obtained from results of these procedures were used to estimate the effect of the swelling of trace amounts of mont/tlorillonite on the permeability of the .samples. Most of the damage to the permeability when reservoir sands containing trace amounts of montmorillonite are exposed to fresh water is due to dispersion and movement of clays. Blockage of pores by the increased volume of expanded montmorillonite is believed to result in permeability damage that is small in comparison to the observed damage to the samples tested. INTRODUCTION Studies have shown that permeability is severely damaged when sands containing only small amounts of montmorillonite are contacted by fresh water.15 When samples of sands containing large amounts of montmorillonite are placed in fresh water in the laboratory, these samples may completely disintegrate, forming an unconsolidated mass of larger volume than that occupied by the dry sample." In this case, it is apparent that the swelling of montmoril-lonite has destroyed the pore structure of the sand. If only a trace of montmorillonite is present in a sand. samples may remain intact when saturated with water, although the permeability to water is a small fraction of the gas permeability of the dry sample. Many workers in the field of water sensitivity have attributed this reduction in permeability to the blocking of pores and reduction of pore size by the increased volume occupied by expanded mont- niorillonite. if the sand contains a detectable amount of montmorill'onite or mixed-layer clay containing rnontmorillonite. Logically3 the smaller amount of montmorillonite present in a sand, the smaller should he the effect of montnlorillonite swelling on permeability; however, the quantity of montmorillonite sufficient to cause severe damage by swelling is not known. Although hundreds of samples have been tested in our laboratory, no correlation has been established between the amount of montmorillonite in samples and the permeability reduction caused by fresh water. To many petroleum engineers, the phrase "clay swelling" is synonymous with "water sensitivity", or "permeability reduction" implying that any formation damage due to the hydration of clays is caused by swelling. Although all clays adsorb water on their surfaces, montmorillonite is the only clay mineral commonly found in reservoir rocks which adsorbs water between intercrystalline layers, resulting in expansion of the clay particle. As montmoril-lonite swells, the first few layers of water adsorbed between platelets are strongly held and well oriented, and the montmorillonite retains its crystalline structure, although expanded. As swelling of sodium montmorillonite continues, the platelets become farther apart and the forces orienting the platelets in the crystalline structure become weaker, resulting in a less orderly orientation of platelets. In an abundance of water, small groups of platelets may become detached from the original monl-rnorillonite particle and may be dispersed throughout the water phase. Because of its swelling properties, sodium montmorillonite is very easily dispersed in water. Particles of other clay minerals. such as illite and kaolinite may also be dispersed in water. causing water sensitivity of sands not containing montmorillonite. The presence of an immobile layer of water adsorbed on the surface of clays has been considered a possible cause of the low permeability to water of dirty sands. Grim states that the thickness of the layer of immobile water held by sodium montrnorillonite is three nlolecular layers or 7.5 A (angstroms), with some orientation of water extending to 100 A. Assuming a very thick, immobile water layer adsorbed on the surface of a pore represented by a capillary tube, the maximum effect of the water layer on permeability can be calculated. Using a pore radius of 10 ' cm and an immobile water layer of 50 A. the calculation shows the permeability to be reduced only 2 per cent. Similar calculations can be used to show that the effect of electro-osmotic counterflow is of the same order of magnitude as that of bound water. The reduction of the permeability to water by either an immobile water layer

Jan 1, 1966

By M. Khorouzan, L. Thomas

Designers of semiconductor devices have been strivi,ng to resolve problems associated with Au-A1 alloys in bonded in.tercomzeclions. One approach now being- used is that of waintaining a physical seyav-atioz between the two metals in bond areas. This is accolrzplished by alunzincnz-plating a bonding area on the tips oJ the kovar leads and using alcminurn wires to join the senzicondictor device to the leads. The portion of the kovar lead which is on the externul side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. A discoloration condition originally thought to be sinilar to purple plague, occuving in the yluled uluninur bonding area after package sealing, has been investigated to determine its efiects ipm bond integrity. Electron-micro-probe analysis determined that no1 only gold, but lead, zinc, and silicon were also present in the discolored area. A series of samples conlaining' conkrolled umonts of these inzpitrities weve prepared and subjected to a sil.zuluted sealing process. The investigations swcued that, of the contawiinants, only zinc toas detrinenlul to Lhe bond integily. The discoloration condition itself was found not to be detrimental to the bond integrity. DESIGNERS of semiconductor devices have been striving to resolve problems associated with Au-A1 alloys in bonded interconnections. One approach now being used is that of maintaining a physical separation between the two metals in bond areas. This is accomplished by aluminum plating a bonding area on the tips of the kovar leads and using aluminum wires to join the semiconductor device to the kovar leads. The portion of the kovar lead which is on the external side of the sealed package is gold-plated to provide an oxide-free surface for soldering or welding. Contamination as evidenced by discoloration of the aluminum-plated area was observed in a number of integrated circuits undergoing examination for defect characteristics which cause electrical failures.' This paper contains the results of an investigation to determine the nature of this discoloration, its cause, and its effect upon the integrity of the interconnection bond. I) THE NATURE AND EXTENT OF ALUMINUM-BOND CONTAMINATION The initial hypothesis in the investigation was that the discoloration was caused by reaction of the aluminum film with some unknown contaminants during the sealing of the hermetically sealed integrated-circuit flat package. The package is a rectangular ceramic container sealed with glass which surrounds the kovar leads as well as joining the top to the bottom. The seal is made hermetic by heating and cooling the package to devitrify the glass. In the case of the packages under investigation, the hermetic sealing had been accomplished with dry air as internal atmosphere. The apparent effect of contaminations as observed by microscopic examination was the formation of surface oxides having variations in color encompassing the whole spectrum of visible light. The contamination appeared to be related to one of the more notorious examples of these colorations, the so called purple plague.' In addition to purple plague, Fig. 1 shows the tarnish in the luster of the aluminized surface in the bond area which had been observed in many of the integrated circuits. To identify the contaminant in the bond area electron-probe microanalysis techniques were used.3 Fig. 2 shows the result of this analysis. The contaminants identified were gold, aluminum, zinc, lead, silicon, and cobalt. Fig. 2(a) is a back-scatter display of the area under study. The back-scattered electrons provide a general indication of the distribution of elements in the specimen surface. Elements with higher atomic number scatter more electrons back from the surface and are seen as light areas in the picture. The sample current, Fig. 2(b), is the amount of current conducted by the specimen as a result of electron-beam striking it and is an indication of element distribution. The Sample current is the reverse of back-scatter and complements it. Other pictures in Fig. 2 are produced by characteristic X-rays generated by the elements, allowing the isolation of the element of interest. The isolated element appears white and all other elements are dark. In this manner a comparative study provides a correlation between different surface areas and the elements which are in these areas. The area covered by the gold film, Fig. 2(c), shows that the boundary between the gold film and the kovar is not sharp as expected and that some sort of diffusion has taken place. Fig. 2(c) shows that some gold particles have been carried to the bond area and are in the proximity of the bonded wire in spite of the presence of a physical barrier in the form of the un-

Jan 1, 1967

By Nelson Severinghaus

THIS Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also present, several theories on the action of explosives in this type of blasting. [ ] The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break clown the rock in large blocks.

Jan 1, 1938

By Masatsugu Taniguchi

Onoda Cement Co., Tsukumi is one of the largest limestone producer in Japan. From mines called Suisho and Ganji, it supplies limestone for cement plant, lime manufacture, iron and steel industries and for many purposes. The Suisho mine is highly productive, though it's operations are governed by the utmost regard for its impact on the surrounding environment. However, it became difficult to meet additional expanding demand and to assure continuity of high rate production. Present production rate 1s 6 million tons per year. The Ganji mine, some 2 km south west of the Suisho mine, began first-stage development In mid- 1973 and in january I976 started production. The capacity of major facilities is 9 million tons per year. Full production is predicted in 1979. Mining and milling methods of these mines under strict environmental considerations are discussed.

Jan 1, 1976

By David R. Maneval, W. E. Foreman, J. Richard Lucas

INTRODUCTION The objective of this chapter is to inform the industry, as well as the public, of the challenges in dealing with problems associated with air and water contamination by coal preparation plants. The need for an informed industry is most important. It is hoped that some contribution may be given to a more efficient and economical approach to the problems of plant waste contaminants at individual plants. The problem has many facets, and consideration should be given to specific areas before any significant problems develop at a given plant. It is then possible to have a reasoned approach before the pressures of an emergency environment force hasty and incomplete solutions. It will be necessary to anticipate these problems in the design of new preparation plants, and advance consideration should be given to all problems concerned with contaminants.

Jan 1, 1979

By D. L. Wood

This investigation was concerned with the aluminum-oxide particle dispersions, the mechanical properties, and the re-c,uystallization characteristics of some internally oxidized copper-aluminum alloys. Obserued hardness vaviations are in agreement with variations in oxide particle size revealed by electron metallographic studies. The increase in yield strength caused by internal oxidation is quite sensitive to matrix grain size and is accompanied by a loss of ductility, particularly at higher temperatures. Elevated temperature ductility is con-side,vably improved if major grain reorientation is accomplished by ve recrystallization prior to testing. The oxide particles offer a considerable restraint to softening during annealing after cold deformation. THE diffusion of oxygen under appropriate conditions into a suitable alloy causes solute oxide particles to be precipitated at an inward moving interface.1,2 Previous work has shown that the hardness

Jan 1, 1960

For some years MINING ENGINEERING has published abstracts of the articles appearing in each issue and also of the Transactions papers published in the Quarterly. Beginning this month, a list of key words is being given with each abstract as an aid to indexing the articles for ease in retrieving them when they are needed. The value of a home or office system of indexing and retrieving technical articles is hard to over-estimate. How often is it that a technical problem comes up and someone says: "Oh yes, I've read something about that." Many hours can be expended tracing down that nebulous source. A modest indexing and retrieval system will save those tedious hours, and the person who is able to produce technical documents when they are needed will achieve an enviable status for being on the ball.

Jan 1, 1964

By Mahesh C. Jha

Arsenical gold ores occur in many parts of the world, including numerous mines in Canada and the western United States. Free gold is often finely disseminated in the grains of sulfide minerals, arsenopyrite, pyrite, orpiment and realgar. Generally a sulfide concentrate is produced by flotation. Arsenical ores or concentrates are not amenable to direct cyanidation and therefore are considered refractory. A wide variety of roasting equipment and conditions have been used by the mills to remove arsenic and sulfur from these concentrates. The resulting calcine is easy to cyanide and gold is recovered from the cyanide solution by zinc dust cementation. Room-temperature potential-pH diagrams and high-temperature phasestability diagrams are presented to discuss the chemistry of the gold cyanidation, cementation, and roasting steps in the presence of arsenic. The environmental aspects of arsenic discharge are also included.

Jan 1, 1984

By Nelson Severinghaus

The Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also presents several theories on the action of explosives in this type of blasting. The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break down the rock in large blocks.

Jan 1, 1938

By Nelson Severinghaus

The Rock Chapel plant of Consolidated Quarries Corporation (Fig. 1) is three miles northeast of Lithonia, DeKalb County, Georgia. It was opened about eight years ago for crushed stone aggregate. This paper reviews a number of experiments that have been tried in drilling and blasting, and gives the practice in use today. It also presents several theories on the action of explosives in this type of blasting. The rock worked is a bare dome of granite gneiss about 3000 ft. in diameter, rising 150 ft. above the surrounding ground (Fig. 2). It is uniform in composition and quality, without seams, and extends downward to unknown depth below the quarry floor. A water well drilled 600 ft. remained in the same rock. The principal difficulty encountered in blasting is an easy split, which tends to break down the rock in large blocks.

Jan 1, 1938