Search Documents

The problems associated with the processing of the Tilden ore are very much representative of the problems encountered in plants processing fine grained magnetic and nonmagnetic iron ores. I would like to comment on some of the problems mentioned in Dr. Nummela'spaper and add to his list of research opportunities in the processing of iron ores. Grinding, the most important step in the processing of fine grained iron ores, is synonymous with liberation. One grinds to separate discrete grains of minerals from the gangue. By convention- al grinding in tumbling mills, mostly random size reduction is achieved with relatively little preferential liberation of minerals. Not only are discrete particles broken that should not be broken, but damage is done to the mineral surfaces. The combination of over- grinding and surface damage shows up in lower recovery figures and higher grinding costs. What is obviously needed is a better comminution process that is more discriminating and that would permit liberating mineral particles at the coarsest possible size with a minimum production of fines. Laboratory attempts at such preferential grinding have been quite successful, but technological difficulties have unfortunately prevented its use. Impact grinding is a good example of a new comminution process that has not been accepted because of equipment problems. Either these problems have to be solved or new comminution systems have to be developed to reduce grinding costs and improve liberation. In his paper Dr. Nummela mentions the change in the primary mill throughput that occurs during the winter months. Seasonal changes in the operation of the grinding circuit and other unit operations have been observed in many plants, and many explanations for this phenomenon have been advanced. The fact is that we do not fully

Jan 1, 1979

By R. P. McLaughlin

EXACT information as to performance of the gas lift from the mechanical engineering standpoint is hard to obtain. Several hundred wells are now producing in California fields by means of the gas lift, and a survey of results shows that the gas lift has increased production at these wells by approximately 60 percent. Similar or even larger figures describe results in Mid-Continent fields. Such an increase in output of oil is so satisfactory, to the average oil producer, that it may not encourage investigation looking to more efficient operation. The cost of lifting oil by compressed gas varies from 3 c. to 15 c. per bbl. of oil, depending upon the efficiency of the gas lift. A difference of 10 c. or 12 c. per bbl. of oil is immediately noticed by an oil operator and the cost in production is as real to him as is the price of his product. Therefore, the efficiency of gas-lift process deserves more consideration than it has been given in some quarters. It has been found that there is a wide variation between different operators and at different wells in the amount of gas used per barrel of oil lifted. Some of the most efficient operations show oil being lifted with only slightly over 400 cu. ft. of gas per bbl. of oil.1 On the other hand, wells are being flowed and using as high as 3000 cu. ft. per bbl. of oil. The cost of compressing gas to 300 or 400 lb. varies from 3 c. to 5 c. per 1000 cu. ft. of free gas. This figure has been obtained from a number of sources and as a matter of fact is the basis of actual business transactions involving gas compression. The cost of lifting oil with compressed gas is thus determined.

Jan 12, 1926

By W. E. Thorne

The object of this graphic method is to estimate the weight of the casting, which is to be made from a given pattern, when the cross-section is not a uniform geometrical figure. Such an estimate is a very important guide to the foundryman, who would otherwise guess at the probable weight of a casting of new design, and, in trying to be on the safe side, would probably melt an unnecessary amount of iron. It is also an aid to the designer of a new car-wheel pattern, who must otherwise estimate from general experience the probable weight, have test-wheels made, and correct the pattern afterwards, so as to obtain the weight prescribed. For the method here described, an accurate drawing of the pattern is employed. This gives a closer result than a drawing of the wheel itself, for the following reasons: 1. Calculations based upon the actual dimensions of the wheel involve the erroneous assumption that the specific gravity of the casting is uniform throughout; and upon that basis the calculated weight would be wrong, because the amount of metal poured has shrunk in the mould, acquiring the highest density in the outside chilled portion, and growing less dense through the mottled to the gray portions. 2. Calculations based upon the dimensions of the pattern or " chiller " assume that the cooled metal will not have shrunk, but will have the volume of the pattern and a uniform density. These assumptions, though erroneous, counterbalance each other. For instance, the patterns and the chiller which give a wheel 33 in. in diameter when cold, are respectively 33.5 in. in diameter. This shows a shrinkage for wheel-iron of about & in. (ordinary gray pig is commonly assumed to shrink about 1/8 in.) per foot. Wheels cast in 33.5-in. chillers do not always have the

Jan 1, 1903

By Ralph Nichols

THE mines are near the town of Gilmore, in the Texas mining district. This district was organized in 1880. The present producing mines are near the terminus of the Gilmore & Pittsburg railroad. This railroad connects with the main line of the Oregon Short Line at Armstead, Mont. The distance from Gilmore to Armstead is 70 miles. The town of Gilmore is near the head of the Lemhi river at an elevation of 7,000 ft., while the mines are from 400 to 1,300 ft. higher. The range of mountains upon which the mines are situated forms the water shed for the Little Lost river on the west and the, Lemhi river on the east. The winters are severe and the snow fall is heavy, but the mines ship right through the year. There is an abundance of timber suitable for all mining purposes in the immediate vicinity. Water is piped into the camp from a lake about 2.5 miles distant. This lake is about 1,400 ft. above the town of Gilmore. The water is exceptionally good for boiler and domestic purposes. The mining companies now producing are. the Pittsburg Idaho Co., Ltd. ; the Latest Out Mining & Smelting Co:, Ltd. ; and the Gilmore Mining Co., Ltd. Besides the above properties, there are a number .of prospects in different stages of development. The producing mines of the district are fissures in limestone, with a general northeast-southwest course .and a dip to the west of from 40° to 70°. These fissures are at about right angles to the bedding of the limestones. The veins are regular and the ore shoots strong, both laterally and in depth, so far as developed. The ore shoots have a rake or pitch to the south. The character of the formation is shown in Fig. 1, a section of the Latest Out mine.

Jan 11, 1913

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By Henry M. Howe

The transformation which steel undergoes in slow cooling, from the condition of austenite whelk above the transformation rage into that of pearlite plus either ferrite or cementite below that range, is subject to great lag. This transformation is essentially the pearlitizing of the austenite. Indeed the hardenillg of steel is due to this lag, which is made so great by extremely rapid cooling that a very large part of the transformation itself is restrained, so that the rapid cooling catches the metal in an only partly transformed state, that of martensite, and under favorable contditions even in an almost wholly untransformed state, as in the cases of Maurer's austenitic manganese steel. Hadfield's austemtic. manganese steel, 25 per cent. nickel steel, and other anstenitic alloy steels, arc austenitic even after slow cooling. It has long been known that this lag increases (1) with the rapidity of cooling, (2) with the presence of certain retarding elements, notably manganese and nickel, and (3) with the temperature from which cooling starts. The present inquiry touches the last of these influences, but incidentally it throws light on the first also. This influence of higher heating ill increasing lag manifests itself in different ways which, though they may at first seem unrelated, are in fact hut different aspects of one and the same thing. Thus, among heatings to different high temperatures, all of them above the transformation range: the higher the temperature to which the steel is heated (1) the lower is the temperature at which the transformation occurs in cooling slowly down, (2) the shorter is the time occupied in the actual cooling from above the transformation range to the room Temperature under given external conditions, Whether of slow or

Jan 1, 1914

By G. G. Gunther, C. L. Boeke

THE zinc deleading processes at the Parral and Santa Barbara mills are described separately to provide a basis for comparison. Although the two procedures are fundamentally alike, there are some differences in application to meet specific conditions. The Asarco mill at Parral in the State of Chihuahua is a flotation plant treating 1450 metric tons per day of complex sulphide copper-lead-zinc ores. In general, the procedure used for selective separation of the minerals into a copper, a lead, and a zinc concentrate follows the usual practice. First, a bulk copper-lead concentrate is floated and then separated into a final copper and a final lead concentrate by the sulphurous acid process. A small tonnage of high grade gravity lead concentrate is tabled from the bulk copper-lead cleaner tailing before it is reground so as to avoid undesirable over-grinding and sliming of this portion of the lead mineral. Next, a zinc concentrate is floated from the lead rougher tailing and, as described later, is separated into a final lead product and a final zinc concentrate. Finally, the zinc rougher tailing receives a strong scavenger float to remove all recoverable middling values for regrinding and return to the flotation circuits. The slime is separated from the scavenger flotation product, and only the sand portion goes to the regrind section. The minerals in the separated slime are extremely resistant to all methods of selective separation and pose one of the major problems awaiting solution. Nevertheless, the slime shows a profit when mixed with either the lead or the zinc concentrate, except when metal prices are very low, so it is accepted as a final product for lack of a more profitable method of handling it. In contrast, the minerals in the reground sands of the

Jan 1, 1953

By L. P. Davidson

THE new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, Ill., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through Shriver presses, which deliver the purified solution to storage tanks, and the copper-cadmium-zinc cake is shipped for retreatment and recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutions can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid-either as acid or as sulphate sulphur in the calcine-because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60° Bé. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1942

By J. B. Chatelain, M. F. Dufour

FLUID jet mills, employing a compressible fluid to grind materials to the subsieve range, was developed in the early 1930's, and the subsequent acceptance of these units was the result of their ability to pulverize solids that, because of physical properties, could not be processed by other attrition methods, such as ball, pebble, and hammer mills. Also, the fluid energy pulverizer is the only grinding device that will discharge continuously a 5-micron or smaller product. Simultaneous ultra-fine grinding and classification is the widest application of this unit. Jet mills may be used to advantage to reduce particle size of solids suspended in liquids, for coating one material with another, and effecting chemical reactions and changes in physical characteristics other than a reduction in size. Materials that can be processed by this grinding method include nonmetallic and metallic minerals, ores, metals, pigments, insecticides, fungicides, pharmaceuticals, plastics, dyes, and numerous other organic and inorganic products. Grinding principles utilized in the fluid mills available on the market are basically the same, the major difference being in the shape of the, grinding and classification chamber. Grinding in fluid jet pulverizers is accomplished by collisions between particles of the material being ground with the energy being supplied by compressed fluids entering the grinding chamber at high velocities. The "Micronizer" is a fluid energy mill employing a relatively flat cylindrical grinding chamber. Fig. 1 shows general construction details. The mill shown is equipped with a venturi type feeder using a compressed fluid to inject the feed into the grinding chamber. The energy consumed in forcing the feed into the grinding chamber against the mill pressure is, in some cases, as much as 40 pct of the total required for processing. Recent improvements, using a compression screw feeder as shown in Fig. 2, can reduce this to 1 or 2 pct of the total energy requirements. Grinding Grinding, as carried out in the. Micronizer involves the action of gaseous jets emerging from nozzles located in the peripheral wall of the grinding chamber. The axes, of the jets are tangential to a circle of smaller diameter than the grinding chamber as is shown in Fig. 1, and the gases entering the chamber maintain a high rotational velocity. The feed introduced into the mill is accelerated by the rotating gases and is thrown to the outside where a portion, coming in the zone of action of a nozzle, is further accelerated tangentially and inward. Violent collisions occur between the particles so accelerated and other particles circulating at a slower rate in a thin band near the periphery. It is estimated over 90 pct of the reduction in Micronizers occur as a result of impact within a fraction of an inch of the orifice. Observations also indicate that size reduction is independent of any interaction with the walls of the

Jan 1, 1952

By L. P. Davidson

The new electrolytic zinc plant of the American Zinc Company of Illinois commenced operation in April 1941. The simple flowsheet using the standard current density and the economic reasons that dictated it are given herewith. The Evans-Wallower Zinc Co. built an electrolytic zinc plant at Monsanto, 111., in 1929 and operated it for about two years. The plant stood idle from 1932 and was purchased by the American Zinc Co. in 1940. Because of the condition of the , equipment, excepting the motor generator set, a complete rebuilding was necessary. The Fairmont City plant of the American Zinc Co. could treat the leach residues, the purification cake and the skimmings from the melting furnace in its various plants. This possibility permitted a simple flowsheet with good economic results. The flowsheet is shown in Fig. I. The calcined concentrates are leached in mechanically agitated tanks with spent electrolyte and such ferric iron solution as necessary. When the acid has been neutralized and the iron coagulated, the fluid is discharged to settling tanks. The underflow from these thickeners is filtered on a Moore filter; the filter cake leaves the plant for retreatment and the filtrate joins the thickener overflow. Zinc dust is added to this solution until the copper and cadmium are precipitated. The pulp is filtered through shriver presses, which deliver the purified solution to stor- age tanks, and the copper-cadmium-zinc cake is shipped for retreatment snd recovery of these three metals. The purified solution is electrolyzed; the regenerated acid is returned for use in the leaching plant and the cathode zinc, after stripping, goes to the melting furnace, from which it is cast in slabs. The skimmings from the melting furnace are shipped to the Fairmont City plant for reduction to metal in the retort furnaces. The choice of this simple flowsheet was made possible only because of the facilities of the Fairmont City plant. The long leaching period, with high acid content and high temperature which characterize the high-density process, gives a higher zinc extraction but also dissolves more impurities, which must be removed. The same is true to a lesser degree of the multi-step leaching of the western low-density plants. By the sacrifice of some initial extraction, solutid'ns can be obtained that are relatively easy to purify and give good ampere efficiency. This loss in initial extraction is made up in the retreatment of the residues in the Waelz plant. The impurities that accompany the zinc thus extracted are inconsequential when the Waelz product is treated in a distillation plant. It was recognized that this flowsheet would require a somewhat greater amount of sulphuric acid—either as acid or as sulphate sulphur in the calcine—because of poorer washing. The sulphuric acid plant at Fairmont City could deliver 60" BC. acid to compensate for the sulphate loss and the cost would be less than the cost of more intensive washing.

Jan 1, 1944

By M. N., Short

TIE Pioneer mining district, better known as the Superior district, from its principal town, is located in Pinal County in south-central Arizona about 80 miles east of Phoenix and 22 miles west of Miami. The region embraces a confused series of mountain ranges of moderate FIG. I.----SUPERIOR, LOOKING NORTH FROM SOUTH BANK OF QUEEN CREEK. MAGMA MINE IS INDICATED BY WASTE DUMP IN GULCH TO RIGHT OF CENTER. height but precipitous slopes, between which lie irregular valleys filled with alluvial detritus. The average elevation is about 2800 ft. in the valleys and the summits of the ranges reach 2000 ft. above this. Superior is situated on the north bank of Queen Creek where it emerges from one of those ranges into a more or less basin-shaped valley. The drainage of Queen Creek is to the southwest and the flood waters spread out and lose themselves in the desert northeast of Florence, the county seat of Pinal County.

Jan 2, 1926

By Y. Nakada, U. F. Kocks, B. Chalmers

The stress-strain behavior of the gold single crystals in easy glide was found to be affected by the specimen dimension which is parallel to the projection of the Burgers vector of the primary-slip system. The larger this dimension is, the larger is the slope of easy glide. Previously severa1 investigators attributed the size effects to either the existence of surface films or the grip constraints. However, in this experiment both of these possible causes were not present. It is proposed that the length of slip path (defined as the crystal dimension parallel to the Burgers vector of the primary system) is the controlling factor in the size effect observed in gold. THERE are many possible effects of the specimen dimension on the work-hardening behavior of single crystals: grip effects which prevent end regions of the crystal from deformation or rotation; effects of a surface film, for example a coherent oxide; effects of a subsurface layer of accidental or intentional

Jan 1, 1964

By Frederick Clapp

INTRODUCTION - SCOPE OF DISCUSSION There has hitherto been no systematic effort to make public the available information on petroleum in South America and the object of this paper, therefore, is to broadly discuss the subject as it pertains to South America as a whole, endeavoring to collect in readable form what is known regarding individual fields. This article is not intended to exhaustively discuss individual fields, or to solve the many complicated problems regarding petroleum and natural. gas in the various republics, since those necessitate years of study and work by petroleum geologists, engineers, financiers, and drillers. Neither. can the reader expect absolute accuracy in all statements, since this is impossible at the present time. The writer has, of course, attempted to be correct in all cases, but in a review involving so many countries and extending over so many, phases of the subject, it is to be expected that some errors will have crept in.

Jan 10, 1917

By T. P. Meloy

In a recent paper, Gaudin and Meloy1 derived a size distribution function for single, impact fracture. Mular2 extended the use of this size distribution to describe the output of carefully controlled grinding experiments. As it stands, the function is difficult to compute. Consequently, a series of tables of the function are presented below: where M(x) is the cumulative fraction finer than size x when x is particle size. Weight percents are tabulated for the single parameter, r, in three different size ranges: from 0 to 1, from 1 to 10 and from 10 to 100. Tables I, II and III are cumulative percent finer and Tables IV, V and VI are for weight percent passing screen size x, retained on the screen below. A number of conditions from the table are plotted in Figs. 1 and 2. Fig. 1 is a plot of the cumulative percent finer vs. size, and Fig. 2 is the weight per-

Jan 1, 1963

By T. F. Adams, D. P. Morse

Tunneling is primarily an excavating cycle consisting of a sequence of operations: drilling, shooting, ventilating, mucking, and erecting supports, if necessary. However, the type and condition of the ground that is being worked, as well as the size and shape of the tunnel, determine the rate of advance. In addition developments in drilling, ventilation, mucking, and haulage equipment have contributed to faster tunneling. Geology: This discussion will be limited primarily to rock tunnels or those which require the use of explosives, and the cost and hazards depend primarily on the condition of the rock which may be broken, decomposed, and contain water with gas. Advance geological study is an important part of any tunnel work and helps to minimize serious miscalculations. The geology itself, at best, is a matter of experience and prediction and it is not so much a matter of the types of rock the tunnel may go through, but a knowledge of the class and intensity of the rock defects that may be encountered.

Jan 4, 1958

By S. W. Parr

STUDIES relating to the behavior of coal toward oxygen may have for their purpose the determination of the fundamental factors that underlie spontaneous combustion, weathering and deterioration, and the general topic of storage, as well as those properties that have to do with the underlying principles of carbonization. There is also involved the possibility of developing information relating to the constitution of coal, or at least the chemical properties inherent in the type substances of which the coal is composed. It is the purpose here to record certain FIG. 1. results bearing on this latter idea of the chemical properties that characterize the main constituents of bituminous coal. The avidity of freshly mined coal for oxygen has long been known. What happens to the coal or to the oxygen is not so clear. Is the oxygen absorbed or chemically combined, and what are the conditions as to time, temperature, texture, or components that are most involved in the phenomenon?

Jan 6, 1925

By John R. Dyni

Colorado nahcolite deposits, estimated at 29 Gt, formed in an asymmetric permanent-lake basin whose waters were rich in algae and sulfate-reducing bacteria. Nahcolite (NaHCO3) occurs in oil shale of the Green River Formation (Eocene) as aggregates (62%), disseminated crystals (24%), and impure beds (13%). Because much of the nahcolite is nonbedded, it will be mined with oil shale and can be concentrated to marketable grade by crushing and screening. Impurities in nahcolite are kerogen, quartz, pyrite, and carbonate minerals. A promising new market for nahcolite is in the process of removal of sulfur dioxide from industrial stack gases. When heated, nahcolite reacts with sulfur dioxide to form sodium sulfate. Differences in thermally induced microporosity may explain why nahcolite is more reactive than trona, a Possible competitor with nahcolite for SO2 removal. Limited production of nahcolite at one or possibly two localities is expected in the next several years, but large-scale production is probably at least 10 years away.

Jan 1, 1982

By Thomas D. Henderson, Donald E. Crowell

INTRODUCTION This paper presents a "case history" of the steps taken to estimate capital and operating costs for a typical porphyry copper concentrator of ±9,070 metric tons (10,000 short tons) per day capacity. The concentrator described herein is hypothetical, but is based on experience and is, in effect, a composite of several actual projects. The numbers used are illustrative only and do not represent actual costs at any particular concentrator. These numbers are, however, representative of typical milling costs at one point in time, and. are sufficiently accurate to illustrate the cost estimating procedures described in this paper. It is not possible to publish actual, current milling costs and, in any event, actual cost figures quickly become meaningless in today's economic situation with various costs all rising at different rates. The paper is divided into three parts: (1) order-of-magnitude estimate, (2) feasibility study estimate, and (3) discussion of differences between estimated and actual costs.

Jan 1, 1978

By S. A. Braley

DRAINAGE of acid mine water into surface streams of coal mining areas is one of the most serious problems of stream pollution, since there is no known method that completely prevents its forming and no economically feasible treatment after it has formed. The mine acid problem differs from other pollution hazards because acid production does not end with cessation of mining but actually becomes more evident when pumping is stopped. The acid problem in the Pennsylvania, Ohio, West Virginia, and Kentucky bituminous coal areas of the U. S. began with the first operation in 1761, and the volume of acid discharge today is largely the cumulative result of years of mining. Provided they lie above the drainage area, the oldest mines, now long abandoned, are almost without exception producing acid in the same manner as those now operating or recently abandoned. It is well to consider some of the many procedures that have been used to determine the composition

Jan 1, 1957

By R. A. Kinzie

In a conventional cement plant, the drying and heating of the raw material takes place in the upper section of a cylindrical kiln where the heat exchange is poor. In a Lepol kiln this part of the process is carried out on a traveling grate where the heat exchange is efficient. The increase in fuel economy justifies the greater complexity of the installation.

Jan 1, 1950