Search Documents

By Kenyon Burch

ONE of the advantages presented by electric drive in many classes of work is the ease with which the electric motor can be controlled automatically. In a large number of cases certain features of the control are automatic-for example, the rate of acceleration may be limited automatically or the equipment may be stopped automatically at the limit of travel-but the equipment is started and ordinarily is stopped by hand. . In other cases the motion of the machinery is utilized to start, control the: speed, and stop the motor automatically, independently of any operator. A considerable proportion of the large mine hoists now in use have certain automatic features, particularly protective devices against over-winding, and, in some classes of electric hoists, devices for preventing excessive acceleration or retardation. The large automatic hoists discussed in this paper, however, are completely automatic, i.e., capable of snaking their trips without the presence of an operator at the control levers. According to circumstances, various advantages may be obtained by automatic control, chief of which are decreased power consumption', increased precision and safety of operation, and decreased, cost of attendance. The first step in the analysis of a prospective automatic mine hoist is to determine whether automatic operation is feasible at all. If men are to be hoisted, or levels changed, the attention of an operator is required for these purposes; but tinder some conditions it may be entirely practicable and advantageous to build the equipment so that, while provision is made for hoisting mien or changing levels, ore can be hoisted automatically from, any one level. If, however, an operator's attention is required every few minutes for changing levels, handling men or drills, or other work requiring hand control, it is obvious that automatic operation between times will not be of any, practical benefit.

Jan 3, 1916

By W. H. Emmons

INTRODUCTION MINERAL deposits that have formed by the various geologic processes, when exposed to air and water at or near the surface of the earth, break down and form new compounds that are stable under surface conditions. Mechanical disintegration of the ores proceeds along with chemical alteration which generally is attended by oxidation, carbonation and hydration. Essentially all minerals are affected-silicates, carbonates, native metals, sulphides, etc. Where iron sulphides are present, oxidation yields sulphuric acid, and in the presence of oxygen and iron, ferric sulphate, a powerful solvent, is formed. Above the water level, in the vadose or shallow zone, both air and water are present. Below the water level air is excluded and that which is carried down with water is removed from the solution by reactions with reducing materials. Above the water level, solution is the pre-dominating process; below the water level, precipitation generally is equally important. In some deposits, particularly above the hater level, valueless materials are removed from the ore, leaving certain metals in a more highly concentrated state. This type of alteration, which has been termed negative enrichment, is common in ores of iron, aluminum, manganese and certain other metals. Some gold deposits, particularly those in which the environment is unfavorable for solution of gold, have been enriched near the surface by removal of material other than gold. Certain metals are readily dissolved in an oxidizing acid environment. These include copper, silver and, under certain conditions, gold. In the presence of iron sulphides, deposits of these metals are likely to be leached above the water level. The metals are carried downward to depths where air is excluded, and where they may be redeposited, generally below the water level. Such enrichment by addition of metals has been termed positive enrichment.

Jan 1, 1933

By Donald Ofte

LIQUIDUS temperatures of molten alloys were measured in an oscillating-cup viscosimeter by observing the abrupt increase in the alloy viscosity when the apparatus was cooled below the alloy liquidus temperature. The liquidus transformation can be an elusive thermal effect in an alloy system where a small amount of material is involved in a low-enthalpy liquidus reaction, or where other unfavorable physical conditions interfere. Using the viscosity technique, liquidus temperatures were measured in binary alloys of plutonium with cerium, gallium, and iron, as well as ternary Pu-Ce-Co alloys. The previously described oscillating-cup viscosimeter1 is a torsion pendulum consisting of a right circular, cylindrical tantalum cup fitted to a rigid shaft which, in turn, is suspended by a torsion fiber in a highvacuum system. When the torsion pendulum is placed in oscillation the viscosity of the liquid contained in the cup is a function of both the decay of the oscillation caused by the viscous drag of the liquid contained in the sealed tantalum cup, and the period of the oscillation. The period is measured by a photo-electrically operated timer to the nearest thousandth of a second. Prior to each measurement, the apparatus is held at temperature between 5 and 18 hr to assure thermal equilibrium throughout the 8 to 10-cc alloy sample. When the cup, filled with a liquid metal, is oscillating. only a very thin outer layer of the fluid is in motion. This moving annulus represents the liquid's contribution to the moment of inertia of the torsion pendulum. When the viscosity increases, more liquid is placed in motion, and the slight increase in the moment of inertia causes a corresponding increase in the period of oscillation.

Jan 1, 1967

By W. M. Courtis

. There seems to be a well-established belief that there is an indescribable something in the appearance of gold-quartz not to be learned from books, that enables those who are fortunate enough to have acquired the power to recognize this characteristic, to pronounce at once that a certain quartz will or will not pay. The stronger this claim is made, the more certain is the claimant to be one of the self-styled practical miners. After several years spent among the gold-mines of California with practical and professional gold-miners, I have come to the conclusion that very few care to risk an opinion on a piece of quartz until some of it has been "horned out." Nevertheless, there is what the miners call a " kindly " appearance, that is more often followed by good results than is a vitreous, water-wet-looking quartz. A dark, resinous quartz seems to be most in favor, but there are so many exceptions that even quartz as " white as a hound's tooth " produces gold in some mines.. The ribbon-quartz, a laminated variety, separated by thin talc or chlorite partings, has a well-known good name. The slides of rich quartz specimens show that this parallelism is a microscopical characteristic of the only macroscopical distinction that, as a rule, these quartzes show. This is shown by Nos. 12 and 13, photographs of the richest quartz, that averaged $65 per pound. It is noticeable, also, in Nos. 7 and 9, and others. Dr. Hensoldt, of Columbia College, who prepared, excellently, a large number of my slides, and whom I have to thank for descriptions and suggestions, says of Nos. 12 and 13: "This variety of quartz differs considerably, microscopically, from the others of your locality, and is, in more than one respect, remarkable. Like the

Jan 1, 1890

By Charles M. Rolker

THE Allouez Mine is situated in section 31, town 57, north of range 32 west, Michigan. The mine is being worked in a conglomerate bed, which conglomerate is generally conceded to be the continuation of the Albany and Boston conglomerate of Houghton County. Besides the well-known Calumet and Hecla with the adjoining Osceola, both working on the same bed, and the new location, the Seneca, now being tried on the Kearsarge conglomerate, the Allouez Mine is the only one working on a conglomerate bed. The Albany and Boston, in Houghton County, of which, as said before, the Allouez is supposed to be the continuation, shares with all the remaining conglomerate beds, near and around Portage Lake, the property of being non-quartziferous, while the conglomerates of Keweenaw County are all highly quartziferous in character. This change takes place, according to Professor Pumpelly, about six miles northeast of Portage Lake. The Allouez conglomerate, with a dip of 38° 15' and a general course of about 36° east of north, is overlaid by a trap, and has as its footwall an amygdaloid. The trap is followed by a series of amygdaloidal melaphyres and true amygdaloids, further on by the greenstone and ashbed ; towards the lake shore alternating traps and conglomerates are found. At the footwall of the Allouez conglomerate, an amygdaloid lies, the thickness of which is not known, which is also the case with the other formations, accurate surveys and geological researches of this district having, as I was informed, never been made. About 198 meters (650 feet), horizontally measured, from the Allouez conglomerate another amygdaloid bed can be traced, on which the present rockhouse stands, further on a melaphyre is exposed, and then follow the diverse conglomerates, the Calumet, the Kearsarge, and Kingston, which, according to the last geological report, are at about the re-

Jan 1, 1877

By John C. Shyne, Eric R. Morgan

WHEN temper rolled low carbon sheet is stored at room temperature before use, changes take place in its mechanical properties. This phenomenon is known as strain aging. Normally these changes are observed by means of Olsen ductility and Rockwell B hardness tests but' unfortunately such tests are relatively insensitive. Strain aging can be readily observed in the laboratory by means of tensile tests. The tensile test method is even more sensitive if the aging is allowed to take place in specimens which have been prestrained in tension rather than by cold rolling. In fact one of the great benefits of commercial temper rolling is that it introduces a residual stress pattern which tends to mask the effects of strain aging when the sheet is finally used in a pressing operation. Curves B, C, and D of Fig. 1 illustrate the changes that take place during the aging of commercial rimmed steel at room temperature following straining in tension, curve A, Fig. 1. The first important change that can be observed is an increase in the stress required to produce plastic flow. This increase is, in this paper, called the aging index. As aging proceeds and the aging index increases, there is also an observable return of the yield point, an increase in the ultimate tensile strength, and a decrease in elongation to fracture. The results of strain aging in deep drawing steel manifest themselves as stretcher strains (L?ders bands) buckling, 2nd tearing. In deep drawn parts such effects are undesirable and strain aging is a serious problem. The rate of strain aging of a steel depends upon its composition and prior mechanical and thermal history? but for most temper rolled ope

Jan 1, 1958

By Klaus Emicke

The paper describes the lead refining process operated at Norddeutsche Affinerie (N.A.). Incoming materials are different grades of lead with varying percentages of impurities: Cu, Te, As, Sn, Sb, Bi, precious metals. The facilities are designed for charge-wise operation. After drossing, generally Te, As, Sn and Sb are removed substantially by the Harris Refining Process using fused NaOH. A certain selectivity during refining is achieved by controlled addition of NaNO3. Another refining step is decopperizing by means of elemental sulfur. Complete separation of Te, As, Sn and Sb is accomplished by chemical methods in a leaching plant. A Howard Press is used in the Parkes Process for desilverizing. After vacuum dezinking in kettle, Bi is removed, if required, by means of Ca and Mg. In an end refining step Ca, Mg and Zn are removed by having the lead melt treated with NaOH and NaN03. The refined lead as such, or in the form of special alloys, is cast by an ingot casting machine into 50-kg ingots. Zinc which is used as a precipitant in the Parkes Process is recovered by distillation from the high grade Ag-Zn-Pb crystals in Faber du Faur retorts while the Pb/Ag alloy is fed to the cupellation furnace. Ca and Mg are removed from the Ca-Mg-Bi crystals formed in the course of Bi removal, and the Bi-bearing lead is cast into anodes. The electrolytic lead refining facilities at N.A. are operated largely for the purpose of separating Pb and Bi. These facilities are also used particularly for the refining of Bi-bearing lead which had gone through the above process, but from which Bi has not been removed by Ca and Mg.

Jan 1, 1970

By J. E. Hove

The high temperature physical properties of graphite are reviewed and interpreted in the light of present day knowledge of the mechanisms affecting these properties. The thermal and mechanical behaviors only are discussed and, whenever possible, comparisons are made with other refractory materials. Possible further studies are indicated, including some carbide work. AS long as the term high temperature implied only temperatures up to about 1000°C, the materials problems which arose could usually be handled by fairly conventional metal alloy types, such as the Co-Cr-Ni superalloys, for which there exists a great deal of technology. Perhaps this temperature can still be considered an upper limit for normal applications, but it is certainly true that the number of abnormal applications is increasing rapidly. The advent, in recent years, of ram-jet and rocket missiles and of high power nuclear reactor heat sources has raised a host of questions concerning the basic problem of what material to use in the temperature range up to 2000°C and higher. While there are, of course, many metals, in the second and third transition series, which melt at considerably higher temperatures than this, these metals are, at present, pretty well excluded from practical use by other considerations, such as re-crystallization, chemical activity, or excessive plastic deformation. The behavior of metals, from the standpoint of dislocation theory, is just beginning to be understood and thus there is some hope for the future development of very high temperature metals, but the immediate problems would most logically appear to have solutions involving the nonmetals, such as the refractory ceramics and graphite. For this reason, there is presently a great deal of engineering and experimental research being performed on the latter materials, much of this research being exploratory in the sense of gathering new property data. The situation, so far as graphite is concerned, is somewhat more fortunate than with the other refractory solids in the sense that a great deal is already known about its basic properties. This stems both from the fact that the carbon-carbon bond has been of interest to chemists for a long time (and graphite can be considered as a very large aromatic molecule, if desired) and the fact that its properties, both as a function of temperature and of radiation damage, are of critical importance to nuclear reactor designers. It is still true, of course, that such fundamental questions as why graphite remains solid to such a high temperature and why it has such a high thermal conductivity cannot entirely be answered at the present time. It is, nonetheless, meaningful and instructive to consider such problems in the light of existing knowledge. This is what the present paper will attempt to do. Before going on, it may be appropriate to classify graphite and justify its discussion before readers primarily interested in metals. Graphite is comparatively unique among materials in that there is always a property or group of properties which precludes calling it either a metal, a semiconductor, or a ceramic. It has the high electrical and thermal conductivities of a metal, but the artificial, poly-crystalline types show a negative thermal coefficient of electrical resistivity, generally characteristic of semiconductors. On the other hand, semiconductors, by definition, show an ever increasing resistivity as the temperature is lowered, whereas graphite approaches a finite, and, indeed, a rather low resistivity in the region of 10°K and, furthermore, a good single crystal of graphite has a positive temperature coefficient, as for a metal.' On still another hand, its porosity and brittleness at lower temperatures would put graphite in the ceramic class although, unlike most ceramics, it is readily machinable and has a high resistance to thermal shock. All things considered, it is probably more nearly appropriate to call graphite a metal than anything else. Although certainly outstanding in some ways, graphite has its peculiarities and, especially if the reader is unfamiliar with the data, it is probably valuable to review some representative property variations at high temperature. This review is meant to be mainly illustrative and no attempt has been made to be exhaustive. Review of High Temperature Properties At ordinary pressures, graphite does not melt, but sublimes directly into the gaseous phase at about 3700°C. Although the phase equilibrium diagram is still in some doubt, graphite will melt, at a slightly higher temperature, at pressures in excess of about 100 atm. The chief difficulty of using graphite in an oxidizing atmosphere is that the reaction rate becomes quite high at fairly low temperatures. If a threshold oxidation temperature2 is defined as the temperature at which graphite loses 1 pet of its weight in 24 hr, the value in air is 450°, the value in steam is 700°, and the value in carbon dioxide is 900°C. Efforts are presently being made to raise this threshold temperature either by impregnation with a retardant of some type (sodium tung-state and phosphoric acid, for example) or by a suitable metal or oxide coating. It is probably fair to say that, to date, these attempts have not shown any outstanding success in all respects. Most commercial graphites are fabricated by impregnating a carbon flour (say of coke or lampblack particles) with some type of hydrocarbon

Jan 1, 1959

By Benj. N. Webber

There is a broad analogy between super gene nickel deposits and super gene copper deposits of the porphyry type. Some of the nomenclature of supergene copper may he applied to super gene nickel deposits. The obvious connection between lateritization and supergene nickel concentration requires some clarification of the nomenclature of laterite of ultrabasic rock parentage. Lateritization is a progressive process and the transition products of the laterite profile are a key to the process of nickel concentration since the profile grades from unaltered peridotite to the highly ferruginous ultimate laterite capping. This profile is formed under highly restricted geographic and geologic conditions. Faulting contributes to the formation and localization of the higher grade commercial segregations of nickel. That there may be auxiliary sources of nickel other than olivine is suggested. The volume of peridotite necessary to produce a unit of laterite at any point in a complete profile is calculated on the basis of the chromite content. The lixiviation, transportation, and precipitation of the elements involved is considered and the source of the reagents and chemical mechanisms are suggested. The role of sodium chloride is considered important. The progressive changes in the lateritic profile have an effect on the general process since lateritization takes place in overlapping environmental phases. The mineralogy of laterite and the redistribution of elements is illustrated by compositional curves derived from a completely mature laterite. Nickel scanvenged by iron oxides tends to be redissolved and moves downward to the zone of transitional magnesium silicates where it is reprecipitated. The geometry of the nickel enrichment zone is simple in general, but complicated in detail. Elongated pods of a greater concentration of nickel are indicated to be a reflection of faulting. Lateritization and concentration of nickel may be arrested at any stage and be modified by several factors.

Jan 1, 1973

By Oliver C. Ralston, James E. Norman

SEPARATION of minerals by froth flotation is rightly called an art. It can truthfully be said that no two ores separate in the same way. The difference in results obtained when natural and synthetic mixtures of minerals are separated is so great that such tests frequently have been worthless in attempting to select conditions in which a natural mixture will separate. With a few rare exceptions, the natural mixture is much more difficult to treat than a synthetic mixture, and a much poorer separation is obtained. Perhaps several experimenters have wondered why 10 or 20 per cent of a mineral being floated from an ore does not float and is different from the 90 or 80 per cent that is recovered. In experimental tests on pure sphalerite, observers1 have noted that varying amounts of sphaIerite may be froth-floated with pine oil alone, the amount recovered in the froth depending apparently upon the source of the sulphide. The only explanation of results such as these, barring insufficiency of frother or time of flotation, is that the surface of the mineral floated is different from that of the mineral depressed. This difference often has been found to be caused by natural contamination of mineral surfaces, apparently brought about by weathering and exposure to natural solutions. There is virtually no rock that is absolutely unweathered. One of the writers had an exceedingly instructive experience in 1931 while working with United Verde copper-zinc iron sulphide ore in Arizona. Nonselective flotation of chalcopyrite and sphalerite away from some of the pyrite was all that could be accomplished. All known depressants produced only slight effect. Sodium cyanide showed some effect, but so much had to be used that only a small amount of chalcopyrite could be

Jan 1, 1939

By A. N. Mitinsky

(San Francisco Meeting, September, 1915) THE theory of elasticity, the science of the strength of materials, and all our calculations regarding engineering structures are based on Hooke's law, that in loaded bodies the deformations are, proportional to the load producing them. Without this law it would be impossible to design intelligently engineering structures such as bridges, frames, axles, etc. This being the case, the proportional limit,1 that is, the point at which deformation ceases to be proportional to load, is the most important factor in engineering design. Further, the working fiber stress should be fixed in reference to the proportional limit instead of, as is usual, in reference to the ultimate strength. The incorrect use of the ultimate strength instead of the proportional limit in setting the working fiber stress is probably clue to two reasons: (1) it is a more delicate operation to measure the proportional limit; (2) it is usually -assumed, though incorrectly, that the proportional limit is determined by the ultimate -strength. In Germany the point at which permanent set first appears is often taken instead of the proportional limit. The two points will coincide if Gerstner's law, that elastic deformations are proportional to the loads producing them both before and after permanent set, is true; and the limit of proportionality and the elastic limit or point of permanent set will both 'be represented on a stress-strain diagram, by the point at which the line ceases to be a straight line and becomes curved-or changes its inclination. It is to be further noted that the difference in definition between proportional limit and elastic limit introduces a difference in methods of determination in the testing laboratory. The German method of determining. the elastic limit by alternately loading and unloading

Jan 8, 1915

By Frank Firmstone

In a paper read at the meeting in Cleveland, Ohio, in 1875,* I showed that as a result of changing from open-topped to close-topped furnaces at the Glendon Iron Works, there had been a decided falling off in regularity of working, which we attributed to the very different distribution of the materials in the new method of filling. Subsequent experience has, on the whole, confirmed the opinions then expressed, and in 1881 we decided to try the modification of the Langen charger, shown on the accompanying drawings, thinking by its use to approximate to the distribution obtained by dumping the barrows at six equidistant points in the circumference of the open-topped furnaces. The top of the furnace is closed by a ring-shaped " bell," as we still call it, the outside of which is cylindrical and rests by the turned lower edge on the bored seat of a " loose ring," supported by the lower part of the hopper. The inside of the bell is an inverted frustrum of a cone, the central opening in which is closed by a cylindrical plug, which is prolonged into a pipe to carry off the gas.? This center-plug is connected by rods and chains to sectors on the ends of a forked lever, to the other end of which is attached, by a wire rope, the piston-rod of the blast-cylinder used in opening the top. The rods connected to the center-plug pass loosely through the apexes of triangular frames, to the other angles of which the bell is attached; it thus being suspended by four points when the top is open. When the materials are dumped out of the barrows into the hopper, a part is thrown over the crest of the bell into the space between it

Jan 1, 1885

By A. D. Rich

THE term "bleaching clay" or "bleaching earth," as used in the oil industries, refers to clays that in their natural state, or after chemical or physical activation, have the capacity for adsorbing coloring matter from oil. There are three common types of bleaching clays: fuller's earth, activated clays, and activated bauxite. Fuller's earth, or naturally active clay, is prepared from bentonites that possess natural activity. It is not activated commercially; in fact, earths of this type ordinarily do not respond satisfactorily to acid activation. Fuller's earth is prepared in pulverized as well as granular form for use in the contacting and percolation processes, respectively. Acid-activated clays also are of bentonitic origin. The basic raw clay, however, is of a type that has a very low natural activity but is highly activable by treatment with mineral acid. Commercial acid-activated clays generally possess several times the decolorizing power (bleaching efficiency) of the best quality of fuller's earth. The former are prepared commercially only in the pulverized grade because of the difficulties in obtaining a satisfactory granular product, and hence are used only in the contact process. Activated bauxite is made by heat-treating bauxite ore, which in its natural state has very little natural activity. The commercial product is prepared in granular form for use in the percolation process on petroleum oils. For the most part, bleaching clay is used commercially in the decolorization of animal, vegetable and petroleum oils, fats and waxes. It is applied in two ways: (1) by the percolation method and (2) by the contacting method. Percolation refers to the passage of oil through a bed of granular clay whereas contacting refers to direct agitation of oil and pulverized clay followed by removal of the clay from the oil by filtration. In either case, the decolorizing effect is obtained by inti-

Jan 1, 1949

By Norbert R. Morgenstern

INTRODUCTION An understanding of the role of water in controlling the stability of rock masses is central for a rational approach to the subject. The presence of water can hinder mining opera- tions in two ways: 1. excessive discharge 2. excessive pressure It should be noted that if the rock mass is very tight, excessive pressures can exist without large discharges. Alternatively, if abundant water is available and the rock mass is open, then substantial discharges can occur under quite small pressures. The problems associated with excessive discharge are usually well understood by the mining engineer. Vehicle mobility is inhibited, some areas are flooded and hence become inaccessible; at best, a costly nuisance exists. The methods of solving these problems are also well-known to mining engineers. They generally involve tapping the source of the excessive discharge and channeling it away in such a manner that any hindrance to the mining operation is minimized. The effects of water pressure on the stability of rock masses are less obvious and the following will be devoted solely to this aspect of the problem. The manner in which water pressures enter into the consideration of stability is made clear by an understanding of the concept of effective stress. THE CONCEPT OF EFFECTIVE STRESS The simplest mechanical model for the problem of rock slope stability consists of a rough, rigid block sliding down an inclined plane under the influence of gravity. This is illustrated in [Fig. 1]. The down-slope component of the weight of the block tends to produce movement which is resisted by the shearing force generated by friction along the base of the block. The shear stress per unit area inducing movement is

Jan 1, 1971

By Charles M. Rolker

The Allouez Mine is situated in section 31, town 57, north of range 32 west, Michigan. The mine is being worked in a conglomerate bed, which conglomerate is generally conceded to be the continuation of the Albany and Boston conglomerate of Honghton County. Besides the well-known Calumet and Hecla with the adjoining Osceola, both working on the same bed, and the new location, the Seneca, now being tried on the Kearsarge conglomerate, the Allouez Mine is the only one working on a conglomerate bed. The Albany and Boston, in Houghton County, of which, as said before, the Allouez is supposed to be the continuation, shares with all the remaining conglomerate beds, near and around Portage Lake, the property of being non-quartziferous, while the conglomerates of Keweenaw County are all highly quartziferons in character. This change takes place, according to Professor Pumpelly, about six miles northeast of Portage Lake. The Allouez conglomerate, with a dip of 38" 15' and a general course of about 36' east of north, is overlaid by a trap, and has as its footwall an amygdaloid. The trap is followed by a series of amygdaloidal melaphyres and true amygdaloids, further on by the greenstone and ashbed; towards the lake shore alternating traps and conglomerates are found. At the footwall of the Allouez conglomerate, an amygdaloid lies, the thickness of which is not known, which is also the case with the other formations, accurate surveys and geologiwl researches of this district having, as I was informed, never been made. About 198 meters (650 feet), horizontally measured, from the Allouez conglomerate another amygdaloid bed can be traced, on which the present rockhouse stands, further on a melaphyre is exposed, and then follow the diverse conglomerates, the Calumet, the Kearsarge, and Kingston, which, according to the last geological report, are at about the re-

By John T. Norton, V.G. Mooradian

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

By V. G. Mooradian, John T. Norton

The diffusion of metal atoms into the crystal lattice of another metal and the assumption of regular positions to form a homogeneous alloy are some of the most fundamental phenomena of structural metallurgy. The mechanism of this process has been the subject of a great deal of study from many viewpoints, but the picture is still far from complete. It is generally believed that if one metal is to diffuse into another, the first must have some solubility in the second1. This means that the solvent must be able to accommodate the stranger atoms, either on points of its own lattice or in the interstices between, without losing its own crystal-lographic identity. It is also a general observation that cold-working is a distinct aid in the diffusion process, causing it to take place with greater rapidity at the same temperature or with the same speed at a lower temperature. There is considerable doubt, however, as to the real significance of the deformation in its effect on the diffusion mechanism. Several factors associated with the cold-working may be responsible for the increased diffusion rate. The plastic deformation causes a distortion of the solvent lattice, which may be an aid in the assimulation of atoms of another kind. There are many references2 in the literature that suggest that some distortion or "loosening" of the lattice is necessary for atomic migration and that diffusion cannot take place in the undis-torted lattice. On the other hand, it may be that the cold-working causes an increase in surface of contact between the two metals through fragmentation or provides a more intimate contact that is necessary for diffusion. If it is true that lattice distortion is an important factor in diffusion, it seems as if there should be some particular relation between

Jan 1, 1935

IN the western mines, the boss, engineer, geologist, or nipper in making rounds have a password which usually guarantees safe entrance to a working place from below the working miner. Most men won't climb a raise or enter a stope from below where a miner is working until they have shouted "nothin' down" and heard those words shouted back by the miners above. "Nothin' down" is a safety pledge as necessary and as binding as the truce flag to the soldier. It implies mutual confidence that work will be suspended until the person below has come abreast of the workers; and also confidence that the miner who replies "nothin' down" is reasonably sure the place is safe to enter. Like truce flags which are not infallible, so is this password subject to human errors or unexpected falls of rock, tools, or timber. Everyone knows these unavoidable hazards, but what is important to the exposed man is that in that precise moment of time when he has heard the reassurance of "nothin' down," he knows that safety is uppermost in the minds of the men above him. With such assurance we would go anywhere and so would most mining men. If that period of safety consciousness, procured by the utterance of two words, could be multiplied to equal the hours in the working day, there would not be any accidents but those by "the act of God." It is the aim of every safety program to make safety as natural as breathing. That is the reason for the posters, the conferences, instruction periods, safety engineers, and the inspections. But none of these are as effective as one accident, which keeps men on their toes for weeks to come. This is not the price we want to pay for safety consciousness. This Annual Review number of Mining Engineering is full of talk about production. Production for defense, production for profit. In this tremendous surge of industrial might . to make this nation and our very families safe S from the predatory forces abroad in the world today; let us not lose sight of the fact that the . safety of our manpower is more precious than any commodity. Production without safety is detrimental to the national interest, to that of the company, and to the individual. If the words "nothin' down" can give us the best human guarantee of safety, for however brief a time, let us adopt them at least in principle as our slogan in 1952. Production for preservation in '52 - but NOTHIN' DOWN!

Jan 1, 1952

By Charles A. Mitke

Discussion of the paper by CHARLES A. MITKE, presented at the San Francisco meeting, September, 1915, and printed in Bulletin No. 105, September, 1915, pp. 1941 to 1958. GERALD SHERMAN, Bisbee, Ariz.-Mr. Mitke justly might have made much stronger his claim for increase in efficiency of labor due to the introduction of forced ventilation. The product per man shift in stoping in the Gardner division has practically doubled. While it is true that improved methods have been responsible for a great part of this gain, and what is due to better ventilation cannot be definitely known, yet it is also true that the results could not have been obtained in that division as it was in 1912. . The paper discusses the two systems of ventilation in use, exhaust and pressure. In both the object is the same, to take foul air or gas out of the mine by the most direct course and replace it by fresh. In coal mines, the exhaust system is in almost universal use, and since the most advanced work in ventilation has been in that class of mines, it was naturally the first one to be considered. It has the advantage of leaving all adits, shafts, or other openings free for use. Doors are only needed to direct the course of the air, and not to confine it. Its disadvantages appear in case of fire, or if the ground over the mine is much broken by subsidence. The fan must work in gas in the case of a -fire, and may be. damaged or destroyed either by heat or by corrosive gas. At the time of the fire in the Lowell division of the Copper Queen, a small exhaust fan was placed over a ventilating raise, but the vanes and housing were destroyed by sulphurous gases within a few weeks. If the ground above the mined area is much broken, as is frequently the case when the ore deposit is thick vertically, a good deal of air is likely to pass through it, particularly if it is near the surface. Leakage from this source is a loss to the exhaust system by short circuiting, which is exaggerated by a contraction or block in the air course. It serves as an added outlet in the pressure system. This is strikingly shown at the United Verde, where many jets of steam may be seen coming up through the ground above the stoped country on a cold day.

Jan 12, 1915

By Andrew Allen

WHEN a mine is changed from hand, to me-chanical loading, the character of the coal dumped at the tipple is changed in many ways. Selective mining is not so easy with mechanical load-ers, and where much picking is done at the face it is apt to be wasteful anyway. Much recoverable coal is apt to be lost by too free gobbing and, in my opinion, picking at the face should be confined to removal of heavy rock, such as pieces of roof or bottom or sulfur balls. and to such clearly defined and persistent bands as can be readily recognized and segregated. With mechanical loaders of the shovel type, even this amount of gobbing is almost impossible. When coal is shoveled into a conveyor there should be no difficulty in doing as much picking as now by hand loading. The size of lumps may be greatly increased, on ac-count of the ease of handling them with a shovel, as the miners will not break them up in order to lift them into cars. Fines may be increased. This is, of course, not universally true, yet it is my opinion that a shovel breaks the coal more, as a rule, than hand loading. This might not be true with all types of shovels and is cer-tainly not true with a conveyor, either with or without the "duck-bill." The average car load will be greatly reduced in fields such as Illinois and Indiana, in which it is the practice to build up the coal above the sides. Where "level full" regulations prevail there should be no material change. When the coal comes to the tipple these differences usually result in the discovery, that many changes are necessary in the preparation plant. The increase in the percentage of fine sizes will probably not bother the screen, but may overload the conveying apparatus. The larger size lump may clog the chute, but as a rule the efficiency of the sizing screens is not greatly affected. In one completely mechanized mine the proportions of 6-in. lump and 2-in. screenings, when loading by hand, were 16.9 and 51.3 per cent respectively. When loading mechanically, these proportions changed to 15 per cent lump and 53.5 per cent screenings. The picking force on the tipple has been increased from 14 on hand loading to 33 men on mechanically-loaded coal. This is for an output of about 5000 tons.

Jan 4, 1927