Search Documents

By Anderson Rosa Pereira

A constante busca pelo aumento contínuo de produção e redução de paradas não programadas em transportadores, tem gerado demanda para equipamentos inteligentes dotados da capacidade de corrigir os constantes problemas de desalinhamento dos TCs. Os métodos hoje utilizados para corrigir este problema são prioritariamente passivos, o que impossibilita uma intervenção mais direta, precisa, automática e efetiva no posicionamento da correia. Esta publicação descreve o funcionamento e os resultados obtidos com a integração do sistema Alinhador Inteligente para Transportador de Correia AITC em um transportador de minério de ferro com vasto histórico de problemas de desalinhamento. Assim, a linha principal deste artigo mostra através de um exemplo prático os benefícios e ganhos mensurados com a aplicação do Alinhador Inteligente para Transportador de Correia.

Aug 16, 2017

By Henrique Silva Furtado

Concerning production of low phosphorus steel critical grades at ArcelorMittal Tubarão site, bottom blowing system plays a very important role. For those systems with independently controlled tuyeres, some non-uniform bottom blowing patterns seem to be promising in improving metal-slag mixing; however, based on computational fluid dynamics (CFD) results of ArcelorMittal Tubarão’s post oxygen bottom blowing, this may not be generalized. Also, from industrial trials it became clear that higher the bottom blowing flow rate, the closer were the end point P to the equilibrium. Despite this result an analysis of the apparent mass transfer coefficient has shown a week correlation with the classical power stir correlation suggesting a more complex kinetic limiting step for phosphorus removal.

Jul 30, 2018

By D. F. Rodríguez-Pérez, J. Salinas-Reyes, Luis R. Salazar-Garza, C. A. Gómez-De-La-Garza

The Pickling Line Tandem Cold Mill (PLTCM) from Ternium Pesquería started in 2013. It is a line with 5 stands, 6 high; focused mainly on the exposed automotive market, with a wide spread of products with high quality requirements. In addition the operational continuity is very important, for this, one of the greatest challenges is to ensure operational discipline, the order of production, the quality of the input (hot band), operational interruptions, equipment failure, breakage of strip in the mill, among others. In relation to this, it has a strong impact on productivity, customer compliance, damage to equipment, rolls, safety, quality, reprocessing among others. Here is present the results obtained in the project "decrease of strip breaks" which focused on several fronts, discipline in the order of production, previous review of raw material in surface and dimensional defects with automatic inspection equipment in the hot mill, as well as in PLTCM, generation of logic in the redundant systems of alerts and prevention to avoid or minimize strip breaks that were high impact in the past. All these multidisciplinary actions led as a whole to a significant improvement in the performance indicators of the PLTCM, in productivity, compliance, reprocessing and quality in the cold rolled mill.

Oct 1, 2019

By Felipe da Silva Siqueira, Weslley Luiz da Silva Assis, Camila dos Santos Pinto, André Luiz Moraes Alves, Guilherme Dias da Fonseca, Paulo Rangel Rios

Neste trabalho estudou-se o comportamento cinético das transformações de fases por nucleação e crescimento nas interfaces (faces, arestas e vértices), das matrizes poliedricas de Kelvin, Voronoi e de Monte Carlo, através da simulação computacional. Com o objetivo principal de comparar os resultados obtidos das simulações com os modelos analíticos de Johnson e Mehl, Kolmogorov e Avrami (JMAK), e de John W. Cahn. As matrizes foram geradas por modelos estocásticos e através do método de crescimento do Cone Causal. Em engenharia o entendimento do comportamento das transformações de fases por nucleação e crescimento são importantes para prever os possíveis locais de nucleação, assim como no entendimento do comportamento dos constituintes presentes do diagrama ferro carbono, na decomposição da austenita, no processo de recristalização, entre outros. Desta forma, o modelamento computacional foi utilizado para o estudo das transformações de fases por nucleação e crescimento, obtendo como resultados a fração volumétrica, o caminho microestrutural e a contiguidade, ambos resultados foram importantes para a caracterização microestrutural e para descrever a distribuição dos núcleos no espaço. Com os resultados obtidos observou-se que se os núcleos estão bem distribuídos nas interfaces o impingement será mais fraco, levando as simulações de Voronoi e de Kelvin a corroborarem com o modelo analítico de JMAK, já o Modelo de Monte Carlo, não apresentou o mesmo comportamento, ou seja, ficou evidenciado que nem sempre a aleatoriedade vai ser válida para todos os casos. Foi constatado também que se aumenta consideravelmente a quantidade de núcleos, a distribuição perde a característica de aleatoriedade e passa a se comportar como clusters, corroborando com o modelo analítico de Cahn.

Nov 10, 2019

By Gabriel Gonçalves Pessoa de Castro

O trabalho teve por objetivo produzir uma liga Al AA1070 com microestrutura ultrafina via prensagem por canais equiangulares. O processo empregou a rota C com 2 passes consecutivos a frio e acumulou uma deformação ?2 = 2,38. O material de partida é proveniente de um processo de laminação a quente na qual a microestrutura resultante era composta de grãos grosseiros com tamanho de grão de 14,5 ± 19,1 ?m e dureza de 31,1 ± 1,9 Vickers. Foi realizada a caracterização microestrutural com o auxílio das técnicas de microscopia eletrônica de varredura (MEV) e de difração de elétrons retroespalhados. O comportamento mecânico das amostras foi avaliado por ensaios de dureza Vickers, a fim de se determinar a energia armazenada durante os passes. Os resultados obtidos mostraram que o material de partida apresentou estrutura parcialmente recristalizada, decorrente do processo termomecânico de laminação. A deformação cisalhante severa que ocorre na interseção entre os canais durante o processamento via ECAP permitiu um intenso refinamento de grãos. O tamanho de grão após o 2° passe foi da ordem de 1,6 ± 1,7 µm. A dureza após o 1° passe quase dobrou em relação ao material de partida, mas praticamente se manteve no passe seguinte, sugerindo uma possível estabilidade. Pode-se concluir que ocorreu um considerável refinamento do tamanho de grão em função da elevada fragmentação e rotação da subestrutura após os passes de deformação.

Aug 8, 2018

By Michael Windhager

UltimaTM rolls have been designed for intermediate and finishing stands of rod and bar and small and medium section mills. The rolls and rings are spun cast, with a highly alloyed working layer and a tough nodular iron core. Microstructure and hardness level can be adjusted over a wide range, which allows us to adapt the rolls to differing rolling conditions. After introducing the UltimaTM concept, this paper will describe the results of UltimaTM rolls achieved in various mill applications, like finish rolling of rebar, and slitting. Special emphasis is given to performance gains when using UltimaTM rolls, compared to standard rolls. This paper also examines the impact of UltimaTM rolls on mill and roll shop productivity.

Jul 30, 2018

By Raúl Daniel López

Ternium-Siderar steelmaking has been focused in permanent improvements and process optimization. At present the Slab Continuous Caster N°1 has been totally transformed after 20 years of uninterrupted work. The authors of this paper summarize and comment on aspects which were the main changes and place emphasis largely on those technological developments in which they have been active during that period. Productivity and quality have been our goals during the last 20 years; it has led us to improve process and to achieve better control tools. In the development of this presentation, the authors will put special emphasis on the explanation of those works that were made following their own experiences through the technical personnel who belong to the staff of the company.

Jul 30, 2018

By Carlos Roberto Silva Mamede

A flotação é um dos principais processos de concentração, tendo sido empregada há mais de um século, viabilizando a obtenção industrial de diversos bens minerais, como sulfetos, óxidos, fosfatos, carvão, sais, platinas e outros. Na indústria de minérios de ferro, a flotação reversa de quartzo tem sido empregada com sucesso para obtenção de concentrados (pellet feed) com elevados teores de ferro (próximos de 69%) através de células mecânicas e colunas de flotação. Amidos de milho ou mandioca como depressores, aminas como coletores e hidróxido de sódio como modulador de pH são os principais reagentes atualmente empregados nos circuitos de flotação de minérios de ferro. O esgotamento das reservas de elevados teores de ferro, levando a necessidade de concentração por flotação de minérios de baixos teores, a necessidade de otimização de custos operacionais e a maximização da recuperação metálica são os alguns dos desafios da indústria de minérios de ferro. Além disto, a variedade mineralógica e a ampla faixa granulométrica (0,300 mm a 0,010 mm) são outros desafios desta indústria. O estudo de coletores de flotação mais seletivos para os diferentes tipos de minérios de ferro pode contribuir para aumento da seletividade desta operação unitária.

Aug 1, 2018

By Rudolf Hubmer

In October 2013 JSW Steel decided to place an order to Primetals Technologies Austria (former Siemens VAI Metals Technologies) for the installation of a comprehensive Level 2 process optimization system for more than 20 existing production facilities of various suppliers. For SMS-I new L2 systems are provided for two hot metal pretreatment stations, three hot metal desulphurization stations, three ladle furnaces, two 1-strand slab casters, a ladle tracking system as well as a shop supervisory system. Additionally the existing L2 system for one 1-strand slab caster is being upgraded in the course of the project. In SMS-II new L2 systems for the 7 hot metal desulphurization stations, 4 ladle furnaces, 1 new RH vacuum degasser, ladle tracking system and a shop supervisory system are supplied. Despite of the challenging time schedule the commissioning of the single facilities started within less than 12 month after contract effectiveness. The installed Level 2 process optimization systems together with the achieved results are described in this paper.

Aug 16, 2017

By Washington Martins da Silva Júnior

In stamping process, sliding between metal sheet and forming tool leads to wear of tool surface. Maintenance of stamping tools involves polishing the tool edge, or, in case of severe damage, replacement of the tool. Hard coatings have been applied on the stamping tool surfaces in order to reduce the maintenance cost causing a great economic impact in metal work industry. In this work, CrAlSiN coatings were applied by PVD onto SRV2W tool steel. The coating toughness was avaliated by the critical load in scratch tests. The following coating parameters were analyzed: 1- substrate surface finishing process; 2- coating architecture (multilayer or gradient); 3- chemical composition of the coating. AlSi concentration varied from the substrate/coating interface to the surface. Coatings were 3 µm thick. Scratch tests were carried out using a Vickers indenter. The applied normal load was varied from 0 to 13 N for a scratch length of 5 mm. In order to study the effect in the toughness, the substrate roughness was controlled by the finishing process before PVD coating. Samples subjected to polishing presented highest critical loads. Gradient coatings presented higher critical loads than those with a multilayer architecture. Coatings with higher concentration of AlSi near the surface supported higher loads before failure.

Jul 31, 2018

By Artur Frederico Fonseca da Cruz, Jael Moutinho dos Santos

The problem of iron ore sticking and premature wear on screening rolls on balling systems is recurrent. The importance of the "screening" function of the roller classifier is fundamental, since in perfect conservation state and operation it is possible to ensure the performance improvement of the most expensive phase in the pelletizing production chain, the thermal processing. The present works target is the identification of possible causes of iron ore adhesion in classifier rollers and develop a methodology to evaluate and quantify the iron ore sticking mechanism on the classifier surface. For this purpose, iron ore and additives were collected at four different pelletizing plants in terms of iron ore origins and process flows, three different rollers were chosen for testing around the adhesive energy at the iron ore mixture/rolls surface interface. As results, it was possible to construct methodologies to evaluate the aggregability, it was observed the importance of "specific moisture" definition and knowledge on the adhesive energy increase, besides presenting the better performance of rolls with tungsten carbide coating than other evaluated.

Oct 1, 2019

By Gilberto Álvares da Silva

New elements have been inserted in NiTi lately, resulting in ternary alloys with specific characteristics beyond Shape Memory Effect and Superelasticity. Among all others alloying elements, the Ag additions itself gives potential antibacterial activity to that smart material. So on, the elaboration procedures of ternary NiTiAg alloys was studied in order to obtain a melting procedure to ensure further studies on this alloy. Microstructural and thermal analyses were used to evaluate the VAR-remelting production of NiTiAg with 4.0% wt silver content. The microstructure is composed by a NiTi matrix, pure Ag precipitates, and, scarcely, TiC inclusions. Heat treatments at high temperature could not dilute those Ag particles, but could lead to the precipitation of new ones. The silver element reduces the temperature of the martensitic transformation, yielding a material with superelastic behavior, beyond induces the R-phase on cooling stage of this alloy.

Aug 8, 2018

By Jan Krull

A high productive coke making process in connection with stringent emission control has clearly become a demand of plant operators and stakeholders. Further to this, availability, quality and coal costs are key concerns for the iron and steel industry in its efforts to optimize raw material cost. Today, the optimization of raw material cost in integrated steel works has further gained priority. Coking coal reflects up to 20% of the cost of steel. In top charged batteries coal preparation and blending is one of the concerns to lower coal cost by maximizing the percentage of non-coking coals in the blend. Stamp charging technology is technologically and economically an effective solution in the process of pre-carbonisation. Paul Wurth’s jumbo top charged oven as well as proven stamp charging technology have recently set new benchmarks in Europe, India and Brazil in terms of productivity, stability and emission control.

Aug 1, 2018

By Wen Xuan

Oolitic iron ores have significant economical importance because of their extensive resources in the world. However, their utilisation is often quite limited due to the high content of phosphorus inside. The phosphorus is often finely disseminated in the oolite structure and generally not liberated in the form of free particles. The iron ore used in this work is a typical oolitic goethitic iron ore with high phosphorus. The process of phosphorus removal from this ore is difficult because the phosphorus is not present as distinct minerals. As a result, no physical beneficiation process is able to separate the phosphorus from the iron bearing phases. The current concentrate contains low iron grade (Fe ~49%) and high phosphorus content (P 0.7~0.8%). The acid leaching is a potential way to dissolve phosphorus. Previous studies have shown that the thermal treatment makes the phosphorus more accessible for the acids and enables more efficient phosphorus dissolution. Some chemical additives are reported to enhance this phenomenon. A series of tests have been carried out using roasting - grinding - magnetic separation - leaching technologies to remove the phosphorus from this current concentrate. In the first stage, several tests were performed at pilot scale under the same conditions as described in some publications. The achieved results were similar to those from previous tests at laboratory scale. In the second stage, new test conditions were investigated in laboratory scale in order to achieve better result and to reduce the operational cost.

Aug 1, 2018

By Felipe Beluche Lima, Caio Augusto Silva Santos

Brazil is the largest producer of crude steel in the Americas by BOF process and many challenges come along with the increasing market demand. In the BOF, a tubular wall hood structure has been showing premature failures related to the overlay welded tube technology placed in the hood wall. The main root causes were: thermal fatigue at 1800°C, hot spot formation, high heat-affected zone (HAZ) leading to susceptibility of stress cracking, carburizing corrosion and superficial wearing. Based on that, co-extruded tube technology (named composite tube by Sandvik) was the alternative chosen to enhance hood performance without compromising BOF process. In order to rises safety and productivity, composite tube has 100% metallurgical bond assuring stable expansion, high heat exchange efficiency, better corrosion resistance and less rough surface finishing. It was highly suggested to many others mills due to similar and already existing reported cases.

Oct 1, 2019

By Francisco Morganti

In order to support hot rolling mill managers in improving the utilization of their plants, SMS group offers well defined Performance Modules. These are technologies, components, automation solutions or services, which can be implemented in existing plants to increase competitiveness in categories of efficiency, productivity, quality and process and product control referred to as “Industry 4.0”. Except the Performance Modules dedicated to the last category, targeting overall process controls, Performance Modules are characterized by quantifiable benefits. Performance Modules related to hot rolling mills are e.g. camber free rolling, modular laminar strip cooling system, new edge masking and intelligent components.

Oct 30, 2017

By Xiaowei Du, Xitao Wang, Xuekun Shang

The deformation behaviors under both tensile and compressive forces and microstructure evolutions of cast SA508-4N steel were investigated at elevated temperatures. True stress-strain data were obtained from hot deformation experiments performed on a Gleeble-3500 thermal-simulator under different temperatures (750-1200C) and strain rates (0.001-10 s-1). The reduction of area decreases as a function of temperature from 750C to 900C and then increases. At 1200C, the reduction of area reaches more than 99% with the strain rates of 0.5 s-1 and 1.0 s-1. The dynamic recrystallization under compressive stress occurs at 800C under low strain rate and a complete dynamic recrystallization can be observed when the temperature reaches above 1100C. A “two-stage” flow stress constitutive model concerned with dynamic recovery and dynamic recrystallization was established based on the true stress-strain data. This model shows good agreement with experiment results. Moreover, we developed a dynamic recrystallized grain size model to describe the average grain size after complete dynamic recrystallization.

Oct 1, 2019

By Élida Gonçalves das Neves

Nos últimos anos as siderúrgicas têm investido na melhoria de seus processos e produtos buscando à produção de clean steels, onde menor nível inclusionário é almejado. Neste contexto foi objetivado neste trabalho, em um primeiro momento, realizar uma revisão bibliográfica afim de buscar um modelo que pudesse relacionar a composição química da escória com a capacidade da escória de remover de forma eficiente as inclusões, garantindo assim a limpidez de aços. A partir destes dados, buscou-se, como segundo objetivo, avaliar alguns resultados de escórias industriais e compará-los com o proposto pelo modelo. A viscosidade e molhabilidade foram os parâmetros de maior impacto neste estudo, sendo a viscosidade obtida através da termodinâmica computacional com o FactSage e a molhabilidade estimada a partir do modelo de Nakajima.

Jul 30, 2018

By Maria José Santos Lima

Neste trabalho a estrutura cristalina do carbeto de tântalo (TaC), que é um material extremamente duro, com elevado ponto de fusão e elevada estabilidade química, foi analisada por difração de raios- X e pelo método Rietiveld.Para isto, o carbeto de tântalo foi obtido a partir do precursor tris(oxalato)oxitantalato de amônio hidratado, através de reação gás-sólido e sólido-sólido a baixa temperatura (1000°C) e curto tempo de reação, e foi caracterizado através de Difração de Raios-X (DRX), Refinamento Rietveld e Micróscopia Eletronica de Varredura (MEV). Através das analises de DRX e do refinamento Reitiveld para o TaC com S= 1,1584, observou-se a formação do carbeto de tântalo puro com estrutura cúbica e tamanho médio de cristalitos na ordem de 12,9 nanômetros.

Aug 16, 2017

By Felipe da Silva Siqueira, Mariana Sizenando Lyrio, Aline Cristine Lemos Duarte, Weslley Luiz da Silva Assis, Harison da Silva Ventura, André Luiz Moraes Alves, Paulo Rangel Rios

A nucleação nos contornos de grão é um fenômeno muito recorrente em materiais metálicos. Essa situação foi tratada por diversos autores como Cahn e Rios e Villa, usando a abordagem de nucleação em planos e linhas aleatórias. Neste trabalho estudou-se a nucleação nos contornos do polígono de Poisson-Voronoi e de uma matriz hexagonal em 2-d com métodos analíticos e simulação computacional. Utilizou-se uma equação baseada no método de Cahn para nucleação nos contornos de grão. Para nucleação nos contornos do polígono de Voronoi a equação não mostrou adequação total com os resultados simulados para dois tipos diferentes de casos, já para os contornos da matriz hexagonal, notou-se que quanto maior a quantidade de pontos sorteados na matriz, mais os resultados simulados concordaram com a equação proposta.

Nov 13, 2019