Search Documents

By Raymond W. Henn, Kent A. Pease, Glen J. Rorison

The paper focuses on construction of a 2.55-km (8,365-ft) long, 2.4-m (8-ft)diameter storm drain tunnel in Evansville, Indiana. The tunnel was driven through saturated soft ground varying from clay to fine sand. The paper presents: an overview of design and design rational including specific EPB machine requirements; the contractor’s proposed and accepted alternative construction methods and TBM design; and construction issues and performance. Some of the key points discussed are the use of the TBM in different operational modes for alternative ground conditions, the effectiveness of dewatering systems, production rates, and issues such as surface settlements and gas.

Jan 1, 2001

By R. Sweennen, A. Vervoort, J. Caers

A case study is presented of the mechanical behaviour of fractures in the Westphalian A and B siliciclastic succession of mud-, silt- and sandstones with intercalating coal layers in the Campine basin of northeast Belgium. Mining ceased in the area in 1992 and a pilot well was drilled to assess the feasibility of methane extraction by hydraulic fracturing. Work was carried out to study the influence of types of cement fill in fractures on the shear behaviour of the rocks by comparison with that of the coal seams. X-ray computerised tomography was used for visual appraisal and selection of jointed rocks before destructive shear testing was carried out. Two major type of veins were found to be present, one cemented with carbonate and the other with kaolinite or kaolinite/carbonate. Uniaxial compressive strength and shear tests showed that differentiation of the two types of veins was vital in evaluating the strength of the sandstones, as cementing of the fractures by rigid carbonate minerals can reinstate the strength of the rock masses to that of the intact material. Kaolinite was more susceptible to plastic deformation than carbonates

Jun 19, 1905

By Wittenberg J. C, Reid A. F

A method is described for the rapid and effective production of polished section mounts of ore and mineral particulates to the standards required for automated image analysis. This requires mounting without segregation of particles by mass or density, and it is also preferable to avoid having particles in contact so that they can be recognised as individuals. To achieve this, the particle samples are first split to an appropriate degree in a rotary riffle, and the sub-sample mechanically diluted and thoroughly mixed with an inert filler of the same size range as the particles. Just sufficient epoxy resin is added to make the mixture fluid. During setting, the ore particles are mechanically supported by the inert filler particles, thus maintaining the particles in a random three-dimensional distribution. A rapid two-stage grinding process, based on the successive use of 600 mesh silicon carbide and 1200 mesh (10 um) corundum on cast iron plates, is followed by three stages of mechanical diamond polishing on cloth laps. Hand polishing is entirely avoided, as is the use of papers.

Jan 1, 1984

Using Positron Emission Particle Tracking (PEPT) to Investigate Industrial Systems

Sep 13, 2010

By Reno M. Pappas, Christopher Mark

This report presents results of a U.S. Bureau of Mines study of longwall gob material. The objective of this work was to determine material stiffness properties of the gob for use in numerical models of rock mass response to longwall mining. Photographs of actual mine gob were digitized to obtain approximate particle size gradations of gob material. The gradation curve was shifted down to a lab- oratory scale, and 20 uniaxial compression tests were conducted. Varying the maximum particle size was not found to affect the stress-strain behavior, but changing the gradation appeared to influence the stress-strain behavior. The stress-strain relationship of the simulated gob material was nonlinear, the stress-secant-modulus relationship, was approximately linear, and the stress-tangent-modulus relationship was approximately a second-order polynomial function. Equations were generated from these curves, providing numerical modelers with a means to estimate gob moduli based on the stress level. In addition, the experimental data were statistically evaluated using multiple regression analyses, producing a series of equations to predict the secant and tangent moduli from the given stress level, bulking factor, rock strength, and thickness-to-width shape ratio of the particles.

Jan 1, 1993

By R. F. Balazik

By March 2001, shrinking global markets, reduced consumer spending and declines in domestic manufacturing and industrial output ended the longest economic expansion in US history and pushed the nation’s economy into its first recession in a decade. Aggravated by the terrorist attacks of Sept. 11, the recession led to large reductions in the domestic production of processed mineral materials. Some of the most significant production declines in the US metals industry were registered by aluminum, copper and steel producers. They faced strong foreign competition, higher energy costs and lower prices for their products. However, homebuilding and other domestic construction sectors — major users of nonmetallic mineral products such as cement, brick, glass and stone — remained strong enough to help raise the output of industrial mineral materials slightly above previous year levels. A strong US dollar continued to weaken the competitive stance of US metal and nonmetallic mineral materials companies alike against foreign producers in markets at home and abroad.

Jan 1, 2002

By Patterson B. G

The small party of mining men who formed the original Mount Morgan Syndicate in 1882, commenced operations on the top of the mountain with what were practically nothing more than small hillside quarries, It was not until 1891 that underground stoping began, and open-cut mining therefore commenced with the commencement of operations. This hillside quarrying, however, seems to have been quite haphazard and unsystematic ; there is no trace or sign of any properly devised mining scheme. This can be seen plainly enough from an examination of old mine plans; for in less than five years after stoping was; adopted, the open-cut was down into the stoped-out ground. The following table, prepared from these old plans, shows the downward trend of the excavation in the past fiftyseven years:-

Jan 1, 1939

By Brad Hewitt, Jeff Belke

"Murrin Murrin Operations has not had a successful beginning. Numerous reliability and operability issues many of which are the result of design decisions have been addressed through mechanical and operational changes and the CCD circuit is no exception. Four design aspects of the CCD circuit that have caused and continue to cause operational problems are:1. the inclusion of solution neutralisation gypsum in the CCD circuit feed which was designed solely for HPAL residue without proper investigation of its impact on the achievable underflow density and resulting wash efficiency;2. the decision to construct the thickener base from thickened solids;3. the lack of redundancy in the overflow, underflow and tailings pipe work; and4. the lack of thickener operational flexibility in the central rake-lift and feedwell dilution system.In November 2002, the lack of operational flexibility in the rake-lift and the feedwell dilution system through mechanical modification as follows:•, CCD1 has a modified rake mechanism that now allows central vertical lift of 600 mm;•, CCD1 has forced dilution using the Outokumpu Turbodil® technology and replacing the E-Duc® technology of Eimco;The decision to install, the installation and the results of the CCD1 rake-lift mechanism and feedwell dilution system are discussed in this paper. The installation was justified on improved operational robustness and an increase in the in the underflow density of 1 per cent (per cent w/w). At approximately the same time process modifications in the solution neutralisation circuit were implemented and these changes altered the rheology of the slurry reporting to CCD1. Since the modifications to CCD1 and the solution neutralisation circuit, the CCD circuit has averaged a 2 per cent improvement in the circuit underflow density.The CCD1 modification was completed on time and mechanically has performed well. From a risk point of view, the central rake-lift and Turbodil®dilution system add a degree of freedom and robustness to CCD1 operation that has extended the range of operational confidence. In this respect, the modification has been a success and is complementary solution neutralisation improvements."

Jan 1, 2005

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By Christopher Mark

The Bureau of Mines has recently completed a comprehensive study of coal strength. More than 4000 individual test results from over 60 seams were extracted from the literature and combined in the most complete data base of the uniaxial compressive strength of coal ever assembled. In addition, more than 100 case studies of in-mine pillar performance were available in the Analysis of Retreat Mining Pillar Stability (ARMPS) data base. Statistical analysis of this wealth of data has yielded valuable results. The data shows clearly that the "size effect" is related to coal structure. The widely-used Gaddy formula, which predicts a significant strength reduction as the specimen size is increased, was found to apply only to "blocky" coals. For friable coals, the size effect was much less pronounced or even non-existent. Case histories of failed pillars are the best available data on in situ coal strength. This study found no correlation between the ARMPS stability factor of failed pillars and coal specimen strength. Pillar design was much more reliable when a uniform coal strength was used in all case histories.

Jan 1, 1996

By A. T. Iannacchione

Underground mining of stone in the US is increasing, as is the depth of overburden above the mines. Data gathered from mine visits, maps, discussion with operators and numerical simulation have been used to investigate pillar design and recommend safe practice. Many pillars have slender shapes with relatively large adjacent mine openings: width-to-height ratios range from 0.54 to 3.13 and extraction ratios from 0.56 to 0.91. The pillar material is often very strong and average overburden only 80 m, but occasional failure due to excessive local stress has occurred where pillar size had been unintentionally reduced, overburdens were greater than 200 m, width-to-height ratios were less than 1.25 or extraction ratios were greater than 0.83. Pillars with width-to-height ratios of less than 1.5 appear more likely to fail under excessive stress. When width-to-height ratios fall below 1.0, defects such as through-running discontinuities can have a significant influence on stability. Dip, orientation and material properties are also important

Jun 21, 1905

By D. M. Doyle

A study of the various components contributing to energy costs and their relationships to generally trended operating data, such as tonnage, operating costs, etc., over progressively shorter time periods provides information for an energy audit. A study of annual data gives some insight into the importance of various energy components. As the time frame of the study progresses through monthly, daily and, finally, into quarter hourly data, the variations become more evident and, most important, strategies develop to minimize energy costs. The results of an audit conducted during the summer of 1978 at Wesfrob Mines Limited are reported to illustrate this important phase, prerequisite to a meaningful energy cost avoidance program. The balance of the paper deals with the energy conservation program at Falconbridge Nickel Mines Limited's Sudbury operations, the metering and control equipment, the commitment, the new energy accounting practices and, lastly, the policies. Examples of successful energy conservation endeavours include automatic peak electrical load control, waste heat recovery from mine air and compressor cooling water, energy reductions resulting from lower building temperatures and curtailment of idling loads. The use of pulse meters to measure the flow of gas, steam, compressed air and electrical energy, with their signals interfaced to process computers, allows monthly, daily and, if necessary, immediate reporting of energy and energy per unit of production information The program so reported at Falconbridge's Sudbury Operations is credited with an annual cost avoidance of .9 million dollars in a 14.0-million-dollar annual energy account

Jan 1, 1979

By Patrick E. Durnal

The Richmond-San Rafael Bridge was built in the early 50s' and was first opened to traffic on August 31, 1956. Among California's longest steel bridges, it spans more than 21,000 feet across the northern portion of San Francisco Bay. It is one of six toll bridges currently undergoing seismic retrofit in the Bay area. Current retrofit criteria require the structure not to collapse in a Magnitude 8.3 earthquake lasting 45 seconds on the San Andreas Fault. The earthquake epicenter is 10 miles to the west of the Bridge, near the mouth of San Francisco Bay. Another major fault is the Hayward Fault, with a potential of a 7.5 magnitude earthquake. It is only 4 miles east of the eastern end of the bridge. The retrofit criterion is that the structure survives these earthquakes without collapse or loss of life, and that they are capable of repair within a period of one year. Therefore an energy absorbing, ductility and nominal resistance based approach to the retrofit design have been adopted for the retrofit of this bridge. Foundation Retrofit The foundation retrofits were designed to satisfy of drift criteria of 6 inches at the base of the footings, and to keep the existing H-piles from experiencing unacceptable levels of permanent soil displacement and /or structural rupture. Full-scale structural lateral load testing of BP14x89 piling, to rupture, has helped to determine the drift criteria. However recent non-linear analytical results, have led to a redesign, which may allow for 12 inches of drift. The as-built analysis of the Micropile piers determined that those piers would not exceed the 6-inch drift criteria so lateral resisting shear piles were not needed at those piers.

Jan 1, 1998

By Florian Häckel, Ulrich Schwarz-Schampera, Benjamin Bühring, Katja Schmidt, Dieter Garbe-Schönberg, KoschinskyM Andrea

"The Vanuatu island arc and its adjacent back-arc basins form part of the southern New Hebrides subduction system in the southwestern Pacific Ocean within a triangle defined by the Solomon Islands, New Caledonia and Fiji (Meffre & Crawford 2001). The back-arc region east of the volcanic front is characterized by three structural depressions namely Vate, Erromango, and Futuna (from N to S), also known as the Coriolis Troughs. Earlier studies of lava compositions reveal the occurrence of highly evolved alkali-rich dacites as well as ankaramite basalts within the individual troughs (McConachy et al. 2005).Here we present the first mineralogical and geochemical analyses of hydrothermal fluids and precipitates (sulfides, sulfates, Fe-oxyhydroxides), sediments, and volcanic rocks, sampled during the "Coriolis Volcanism and Vents" (COVOLVE) cruise SO229 in July 2013 aboard the German R/V Sonne. The samples were retrieved during several ROV Kiel 6000 dives directly from the newly discovered active vent sites at the neovolcanic Nifonea Ridge, and from multiple sites at water depths ranging between 200 to 2800 m within the Vate and Futuna Troughs as well as from the shallow water Epi Caldera NNE of the Coriolis Troughs (Fig. 1)."

Sep 1, 2014

By Frank Haehnig, Kjell-Åke Averstad, Johannes Glückert

"AbstractThe Söderströmstunneln is part of the Citybanan project that is currently under construction in the centre of Stockholm. Main part of the lot Söderströmstunneln is a 300m long immersed tunnel connecting the inner-city islands Södermalm and Riddarholmen. It consists of three tunnel elements that have been immersed in summer 2013. Since the solid bedrock is descending in that area to more then 40m depth, the tunnel elements have been placed and are permanently supported on four pile groups that have been constructed in advance. The common Swedish system of steel core piles has been used to built the pile groups. Drilling and installation of the steel cores piles in free water depth of up to 20m had to be done from a pontoon. The steel core piles are connected with underwater concrete pile caps.IntroductionCitybanan is a new 6km long double track railway tunnel running beneath central Stockholm including two new underground stations Odenplan and Stockholm City. When completed in 2017 commuter trains will have their own tracks through Stockholm, whereas the remaining railway traffic will continue to use the exisiting two tracks (see Fig. 1). This will double the capacity of the railway traffic through Stockholm. The Swedish transport administration Trafikverket is the client for this project. The design and built contract is carried out by the German contractor Züblin Spezialtiefbau GmbH together with their Swedish subsidiary Züblin Scandinavia AS.As the new Citybanan tunnel is in large parts situated below the bedrock level, it can be executed as rocktunnel in the common drill and blast method. Between the two inner-city islands Södermalm and Riddarholmen the tunnel is crossing the Söderström, an arm of the lake Mälaren. Here the bedrock is descending to a deep valley with more then 40m depth. To connect the rock tunnels between these islands a 300m long immersed concrete tunnel supported on pile foundations is currently under construction."

Jan 1, 2014

By James E. Hill

Tremendous improvements in mining technology have been witnessed during the past 100 years. For example, before 1860 all blastholes were drilled manually and blasting was done with low-energy black-powder. During the 1860's both the pneumatic rock drill and high-energy dynamite were introduced, ushering in an era of mining mechanization that has steadily progressed since that time. Today, with the rapid implementation of the latest advances in communication science, mining technology is moving into a new era that goes beyond mechanization as such. Transistors, transducers, scanners, telemetry, and the like, all terms largely derived from the new communication sciences, add up to what is popularly know as automation-the communication of machine with machine. Automation is now playing an important role in selected parts of the mining process, such as hoisting, hydraulic roof supports, and underground surface locomotive haulage and belt conveyor systems. But this year marked the first attempt to auto-mate the total mining process with the commencement of production at the British National Coal Boards Bevercotes mine. If this full-scale experiment proves successful, it could lead towards other fully automated mines in both Britain and other parts of the world. This decade, there-fore, could be considered the one that provided the foundation for the mines of the future.

Jan 1, 1966

By D. A. Keefe, O&apos

The electrowinning of beryllium from beryllium oxide (BeO) using a molten-salt electrolyte composed of 56 LiF-37 BeF2-7 BeO (mole-percent) was investigated. Anodes made of porous carbon were found to be superior in current-carrying capacity and gave a lower cell voltage than other types of anode material tested. When porous carbon anodes were used) the resultant increase in anode area prevented anode passivation. The cell voltage was 3.3 volts) and electrode current efficiencies of 50 to 70 percent were obtained. The electrodeposited beryllium was recovered as beryllium powder or was coalesced to metal beads by heating to 1,300° C.

Jan 1, 1970

By J. D. Appleton, J. Ridgway, K. B. Greally

Paper presented at the 28th International Geological Congress held in Washington DC, July 1989 (International geochemical mapping sessions). The results suggest that meaningful geochemical maps can be produced from very low-density surveys, and that existing data sets could perhaps be incorporated into such a map series with the use of a system such as Uniras software. There are still many problems to be resolved, however, including the compatibility of data derived from different analytical methods, and the precise methods to be employed will necessarily require international agreement. Sampling densities should be chosen on the basis of the scale of the geochemical and geological features to be distinguished and will vary from region to region. Reanalysis of selected samples from archives to increase the range of elements determined or to unify analytical methods is only likely to be effective if the original survey was at quite a low density

Jul 1, 1991

By James Dunn

“The strongest argument of the detractor (of mining)is that the fields are devastated by mining operations ...They argue that the woods and groves are cut down, for there is need of an endless amount of wood for timbers, machines and the smelting of metals. And when the woods and groves are felled, then are exterminated the beasts and birds, very many of which furnish a pleasant and agreeable food for man. Further, when the ores are washed, the water which has been used poisons the brooks and streams, and either destroys the fish or drives them away.” Georgius Agricola, 1556, De Re Metallica, translated by Hoover, 1950. Technical problems associated with the cleanup of historic mines are not new. Nor are they unique to the mining industry or the governmental agencies addressing them. Both face the same issues and challenges of defining the problems, evaluating remediation options and finding the most economic and effective solutions.

Jan 1, 1999

By J. G. Haymes

This report by the Bureau of Mines is the first of two proposed papers on evaluation of spectrophotometric, spectrographic, polarographic, and other analytical methods for quantitatively determining impurities in high-purity tungsten. Some of the methods described are standard methods that have been successfully applied to determine low-level impurities, several are modifications of known methods, and some procedures are entirely original. The Bureau of Mines is actively engaged in tungsten research because tungsten has an extremely high melting point, in fact the highest of any known metal. The metallurgist must know the content of impurities in tungsten because of the marked effects even micro amounts of impurity elements have on its physical properties. The Bureau procured a number of analyzed samples of above-average purity from research laboratories of companies engaged in production and fabrication of tungsten. These samples were investigated by the analytical procedures of those companies for several metallic impurities. Subsequent analytical laboratory determination of impurities in these samples agreed with the analyses as reported. With this assurance that analytical methods were basically accurate for metallic impurities, procedures for the determination of several of these elements were modified to lower the limits of detection and increase the sensitivity of methods. Carbon and the gases hydrogen, nitrogen, and oxygen were determined by standard instrumental methods, modified to provide greater sensitivity for reliable determinations when content of these elements was low. After the reliability of the modified procedures was affirmed, they were used as a product evaluation guide in the development of a vapor-plating technique for the production of high-purity tungsten. The following list of elements can be determined by one or more of these methods: AI, B, Be, Ca, Co, Cr, Cu, Fe, Mg, Mn, Mo, Ni, Pb, S1, Sn, Ti, V, and Zn. In addition, a vacuum-fusion method for the determination of H, N, and 0, and a conductometric method for carbon are described. Lower limits of determination and detection for each element listed are given.

Jan 1, 1962