Search Documents

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

By J. K. Gustafson

Since prehistoric times, gold has been sought for its beauty and its unusual physical and chemical properties. Early in the dawn of civilization it became the ultimate unit of value, and for at least 6000 years it has been used to barter for other commodities. It has been prospected for, treasured and made into works of art and personal adornment. From time to time, it has even been the object of conquest. Because of its predominant role as a basis for money in recent centuries, economists have come to think of gold solely in these terms. Gold, however, has physical and chemical properties that make it one of the most useful metals in the modern world. It is the most ductile metal known. An ounce of it can be drawn into a continuous wire over 35 miles long. It is also so malleable that an ounce of it can be beaten into films 0.00001 in. thick covering 68 sq ft of surface. It has a density of 19.3 and is so heavy that 1 cu ft of it weighs more than half a ton. Gold is nonmagnetic and has a high electric conductivity that is only slightly less than that of silver and copper. Gold is so inert to all the chemicals found in nature that gold coins and jewelry buried beneath the soil or at the bottom of the sea for thousands of years appear to be as bright and perfect as when they were first immersed. Finally, gold has an extremely high reflectivity of both light and infrared rays.

Jan 1, 1971

By Freeman Bishop

More than a few discussions are taking place these days among management economists seeking a way out of the dilemma of lower productivity vs. higher labor costs. Most suggestions would be illegal under present antitrust laws. Otherwise interindustry cooperation could be used to divide up some of management's tasks. Or price structures might be tuned to the special machinery and skills of some plants. Both remedies would be under attack almost immediately. There is one other remedy that is getting lots of attention: some form of compromise between management and labor to phase out no longer needed work practices that unions insist shall be retained. Railroads are the national industry suffering the most from this disease, still known as "featherbedding," an epithet coined by the railroaders themselves.

Jan 1, 1971

This volume constitutes the Survival Subsystem portion of the final report for the Coal Mine Rescue and Survival System (CMR&SS) program, which was conducted by the Westinghouse Electric Corporation under contract to the United States Bureau of Mines (Contract Number H0101262 dated June 17, 1970). The program was directed by the Special Systems Department of the Westinghouse Baltimore, Maryland, facility. The basic objectives of the CMR&SS program were to develop and test hardware to determine the efficacy of a variety of coal mine rescue and survival concepts and techniques. These concepts were drawn from two major sources: the Request for Proposal from the Bureau of Mines1 and the final report on the Mine Rescue and Survival Study conducted by the National Academy of Engineering2 (NAE).

Jan 1, 1971

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By Damon C. Gray

This report contains a recommended program of acoustic research to be conducted by the U. S. Bureau of Mines. The program is directed toward the abatement and control of machinery noise in underground coal mining operations. The study conclusions and specific problem areas which led to the definition of the recommended program are also briefly described.

Jan 1, 1971

Presented in this volume are the basic mining techniques and production operations associated with underground bituminous coal mining. Chapter 2, "Multiflow Process Charts", presents, in sketch form, a description of the various operations characteristic of conventional and continuous mining. In order to focus attention upon the major components and operations in each work cycle, certain items are not shown in the sketches, e. g., machine electrical cables, brattice, and rib posts. The elapsed time shown for each sketch is considered representative for the various work elements summarized by the sketch. More detailed work element times can be found in Chapter 3, "Typical Work Cycle Times", and Chapter 4. "Standard Time Data".

Jan 1, 1971

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

The strippable reserves of bituminous coal and lignite in the United States were calculated in accordance with the prevailing conditions of seam thickness and depth of overburden in each of the several coal-producing areas of the Nation. Within defined limits of seam thickness and depth of overburden, it is estimated that there was a remaining strippable resource of 118 billion tons of raw bituminous coal and lignite as of January 1, 1968. Because of topography, natural and manmade features, and other limitations, only 45 billion tons of the resource are strippable reserves. Of this, 32 billion tons is considered low-sulfur (less than 1 percent), 4 billion tons is medium-sulfur (1 to 2 percent), and 9 billion tons is high-sulfur (over 2 percent) coal. Owing to a cleaning loss affecting that portion of strip coal that is mechanically cleaned, the 45 billion tons of strippable reserves are reduced to 39.6 billion tons of marketable coal. A brief discussion is given for each coal-producing State, summarizing past and present production, historical background, and outlook. Appendix A contains reserve data by State, county, seam, and sulfur content. Appendix B contains the general information and requirements necessary to comply with the current strip mining laws covering 20 States.

Jan 1, 1971

In 1970, the U. S. Bureau of Mines contracted with Theodore Barry and Associates, a management consulting firm, to perform a one-year industrial engineering study of working-face hazards in underground bituminous coal mines. The field data was accumulated from industrial engineering observations in fifty underground mines. Supporting data for the analysis was derived primarily from the Bureau's fatal accident reports for the years 1966 through 1970. This report, Industrial Engineering Study of Hazards Associated with Underground Coal Mine Production, consists of three main parts: 1) The Fatal Accident Reports Analysis, 2) The Industrial Engineering Analysis, and 3) Multiflow Process Charts and Standard Time Data. The Fatal Accident Reports Analysis (Volume I, Section II) is based upon individual USBM fatal accident reports for 1966-1970. These were read, coded and computerized in terms of 84 significant variables. Cross-tabulations of these variables have been used to identify major underground hazards and to quantify significant causal factors. A very strong relationship was found to exist between fatal accident occurrences and low task experience. This led to a recommendation for formalized training, certification and supervision programs for miners. Victim compliance with federal regulations, mine regulations and supervisor instructions was analyzed, indicating that supervisors provide the most crucial communication link to workers. Thus, every attempt should be made to ensure the competence of immediate supervisors in the industry. Analysis of roof fall variables revealed a fatal propensity on the part of the miners to work under unsupported roof or under support conditions that are marginal. The technical approach to the problem is to make it physically impossible for a miner to work under these conditions; the behavioral approach is to ensure adequate training and develop proper safety attitudes among the miners. The Fatal Accident Reports Analysis revealed a need for normalizing data to interpret the results more accurately.

Jan 1, 1971

By Jan Zwarcendyk

This study is primarily directed toward providing an understanding of the economic complexities associated with subsidence damage on the surface resulting from underground mining. Some of the pertinent theories on the physical stresses involved are reviewed, and both remedial measures and relevant laws in various countries are discussed. Part I (Chapters 1-3) is an historical overview of various aspects of subsidence problems (theoretical, remedial, and legal) during pre-World War I, between World Wars, and post-World War II, respectively. Part II (Chapters 4-9) presents a comprehensive analysis of the economic aspects of subsidence in relation to the following mining alternatives: (a) carrying out the lowest cost mining method without regard for any surface subsidence, (b) special mining techniques, (c) partial mining, (d) full recovery with stowing, and (e) sterilization or leaving the mineral unmined beneath selected areas. These alternatives are evaluated in terms of their measurable expenses.

Jan 1, 1971

By G. H. Keith

Electrowon tungsten powders were investigated with respect to consolidation, fabrication, and mechanical properties. Sheet, 0.03 inch thick, was produced and its tensile strength measured between 250° and 1,935° C. The large particle size of electrowon tungsten effectively precluded sintering to a density sufficient to allow hot working to sheet or bar. The powders were consolidated by die pressing to 70-percent density, sheathing in molybdenum, and high-energy-rate extruding to either round or sheet bar of 100-percent density. The material was then rolled conventionally to sheet. The mechanical properties of the sheet prepared from the electrowon powders compared favorably with those reported in the literature for sheet prepared from commercially produced hydrogen-reduced powder.

Jan 1, 1970

By S. F. Radtke

The properties and characteristics of lead and zinc have made these metals useful to man in many ways since the days of antiquity. Despite their long history of use, however, these metals have proved to be extremely resilient and responsive to modern needs. New alloys and compounds continue to be developed, adding to the growth of these metals. Consumption data is given for 1969 and compared with one and two decades ago. Trends in major markets also are cited and explained. Uses for lead and zinc which have come into prominence within the past few years are described and explained, with emphasis on the role played by the industry's cooperative research program. Current efforts in the research phase are discussed, with details given on major efforts for both metals, including new alloys, process developments, applications research, finishes, coating, paints and pigments, batteries and fundamental research. A forecast is given of promising new areas and a projection made on a longer term of new applications that may emerge from current research.

Jan 1, 1970

The Bureau of Mines analyzed the cycle of secondary gold to determine the quantity of gold not being recovered from scrap, and to identify areas for research to increase the supply of gold from scrap. Secondary gold in 1967 was estimated to be 2.4 million troy ounces; this excludes secondary gold which is recycled within consuming plants. Firms contacted included consumers using about 41 percent of the gold in 1967, And refiners that recovered about 90 percent of the secondary gold. Results of the study indicate that loss of gold is small, and refiners and consumers are accelerating programs designed to reduce recovery costs. With the increasing generation of low-grade industrial scrap, research is needed to improve present recovery techniques and to develop methods to accelerate the flow of secondary gold back to supply.

Jan 1, 1970

By Cuppam Dasarathy

The incidence of liquid inzmiscibility in binar)) indium alloys has been theoretically analyzed on the basis of the Hildebrand-Alott equation. Bedictions of miscibility or otherwise Imve in general been found to agree with those phase diagrams that are already publislzed in the literature. Out of a total of 27 systems, where either the complete phase diagrams are published or liquid immiscible behavior is reported, the Predictions agree with the experimental data in 25 systems, the exceptions being the Te-In and Ni-In systems. According to the equation, liquid immiscibility is also indicated in the binary alloys of indium with K, Rb, Cs, Na, Sr, Ba, Ti, Zr, V. Nb(Cb), Ta, W, U, Re, Ru, Rh, Os, and Ir. RECENT investigations by the author have shown that indium when alloyed with iron, chromium, and cobalt shows liquid immiscible behavior.1"3 The Fe-In phase diagram shows a wide range of compositions where the liquids are immiscible.4,5 No intermediate phases are present in this system. No precise information is available about the extent of liquid immiscibility in the Co-In system. However, it is certain that there is a range of compositions where the liquids are immiscible and that there are two or three intermediate phases,376 in the system. Liquid immiscibility is also strongly indicated in the Cr-In system and no evidence was obtained in the brief investigation to indicate the presence of intermediate Cr-In phases.2 The present paper deals with a theoretical analysis of binary alloys of indium with certain elements of the periodic table and indicates the systems where liquid immiscibility may be expected. The incidence of liquid immiscibility in binary systems has been theoretically examined by many workers and many excellent papers are available on the subject. In this paper, the alloy systems are examined on the basis of the more recent ideas proposed by Mott.7,8 It has been claimed8 that the Mott parameter predicts the incidence of miscibility or otherwise with reasonable accuracy and consistency. BACKGROUND TO MOTT&apos;S APPROACH Hildebrand applied his immiscibility rule for non-polar liquids to various alloy systems.9 The basis of this rule is that the equation for the excess free energy of formation of a liquid solution is rather similar to the theoretical expression for the energy of mixing of a regular solution. He postulated that when the heat of mixing is sufficiently high, separation into liquid phases will occur and the condition for complete CUPPAM DASARATHY is at the Research Centre, British Steel Corporation, (South Wales Group), Port Talbot, Glamorgan, Great Britain. Manuscript submitted March 12, 1969. IMD miscibility was shown as where VA and VB were the atomic volumes of the components A and B, and ?EV the energy of vaporization of the component. The term (?EVA/VA)1/2 was regarded as a measure of the binding energy of the component A and was called the L&apos;solubility parameter" 8A. On this basis immiscibility occurs when 1/2(VA+VB)(bA-bBf > 2RT [2] Apparently, however, there were several inconsistencies in that according to Eq. [2] several systems known to be miscible in the liquid state were predicted as immiscible. MOTT&apos;S ANALYSIS ~ott&apos;" regards that the reason for the inconsistencies arising out of Hildebrand&apos;s equation was largely due to the electrochemical attraction between the two elements, not being considered. Hence, Eqs. [I] and [2] were modified by taking into account the electro-negativities of the two elements XA and XB, and Mott arrived at an equation for immiscibility, i(VA + VB)(6A - aB)2 - 23,Q60n(XA - XBf > 2RT [3j which can be written as i **&£*&* >&apos;*°™- &apos;• HI T being the melting point of the more refractory component of the system. In Eq. [4], the numerator was called the Hildebrand term, the denominator, the electronegativity term, and their ratio, the Mott number. Mott observed that if the Mott number of a given binary system was greater than the maximum number of Pauling bonds which the two metals could form, then liquid immiscibility could be expected. The maximum number of bonds formed by a given metal was considered to be directly related to the number of bonding electrons available, i.e., to its maximum valency. Since the valencies of the elements considered vary from 1 to 6, Mott assumed that if the ratio of the Hildebrand term to the electronegativity term was >6, then immiscibility could be expected. On the contrary, if the ratio is <1, the metals should be miscible. Further, the alloying behavior is not only influenced by the valencies of the two elements but also by the relative atomic sizes that influence the types of packing and hence the coordination number. Mott considers that on average the maximum number of near neighbors of unlike atoms is 6. Thus, on both valency and size factor considerations, Mott concludes that the maximum number of bonds&apos; possible in any system was 6, this being the upper limit of the Mott number for miscibility. In considering the alloying behavior of systems with Mott numbers between 1 and 6, Mott plotted the num-

Jan 1, 1970

By W. T. Malone, J. R. Williams, R. L. Tiner, J. M. Tinsley

Hydraulic fracturing methods for production stimulation have become a common procedure in the oil and gas industry. Fracturing treatments are performed on wells of various potentials to help increase the production rate. In addition to the desire for increased production is the need to predict what increase might be expected. This knowledge is useful in economical treatment planning to accomplish the desired production goals for the well. Theoretical production increases due to horizontal radial fractures may be calculated using equations developed from mathematical analyses and electrical models.1,2,6 It also is possible to predict theoretical production increases due to vertical fractures using curves developed from electrical3 and mathematical models.8 However, these studies assumed that the vertical fracture height and the formation height were equal, which may not be true." In addition, the final fracture height through which fluid is produced may not be equal to the created height. The development of vertical fracture proppant transport relationships has made unrealistic the assumption that propped fracture height is equal to created fracture height. Through the use of published proppant transport equations,4&apos;12 it is possible to calculate the height of a bed of propping agent deposited in a fracture of a given height. Assuming that the fluid flowing in the fracture moves through only the propped portion of that fracture (i.e., that the un-propped part of the fracture heals) it becomes essential to know how production increase varies with the ratio of propped fracture height to formation height. It should be recognized that future investigation may determine that the fracture does not heal completely and that a highly permeable channel exists over the deposited bed of proppant. The effect of this channel was not considered for the present study. The following analysis of experimental data allowed development of curves to determine theoretical production increases considering fracture height as a variable. Discussion In designing a fracturing stimulation treatment a number of variables must be considered. The size of the treatment, type of proppant used, proppant concentration, treatment fluid properties and well conditions are all factors affecting the dimensions and permeability of the fracture. Production increase due to a vertical fracture is affected by propped length, height, width and permeability of the fracture for a given set of formation conditions. Production increase may be defined as the ratio of production rate after fracturing to the production rate before fracturing at the same pressure differential, pe — pw. The producing rate in an

Jan 1, 1970

By Larman J. Heath

Wellbore enlargement was tested using hydrazine hydrate in a gas-storage well in Ohio to increase the well productivity. The wellbore was to be enlarged by chemical disaggregation of the sandstone adjacent to the wellbore. Productivity immediately declined 49.1 percent and gradually declined to zero in 7 months. A down-hole camera survey showed a white-to-gray precipitate covering the entire wellbore surface. The precipitate was chemically analyzed and identified as mostly carbazic acid, a hydrazine derivative of carbonic acid. Formation of this precipitate was not anticipated; this viscous sub-stance caused the gradual loss in productivity of the well. The wellbore was not enlarged. Laboratory tests were run to determine what clay stabilization measures could be taken in sandstone cores to prevent clay swelling and particle migration caused by hydrazine hydrate. Normal clay stabilization methods did not prevent the virtually complete loss in permeability to hydrazine hydrate. Other laboratory tests using natural gas diluted with small amounts of carbon dioxide confirmed the ease with which carbazic acid could be formed in a hydrazine hydrate-saturated environment within and adjacent to the wellbore.

Jan 1, 1970

By R. L. Whiting, H. J. Ramey

The basic study from which this paper was prepared was started as the result of the growing need throughout the world for increasing quantities of energy in all forms. Quite obviously, natural forms of energy that are readily available at low development cost are those in greatest demand. The underdeveloped countries — and particularly those having little or no petroleum resources — are the countries in which the most interest is being shown in the newer energy sources. One of the least expensive energy sources is natural geothermal steam.&apos;-* Although this form of energy has been recognized for centuries, it has been only during the past 20 years that serious efforts have been made to harness it. Natural geothermal steam energy in Italy, New Zealand, Mexico, Japan, and California is now being produced through wells to drive turbines and generate electricity. Further, active exploration for natural geothermal steam is being conducted in Hawaii, Fiji, Taiwan, Chile, Russia, Greece, and Katanga. It is surprising to find that most geothermal steam exploration is in the "steam seep" stage. That is, surface studies are made and exploratory wells are drilled in the general area of steam seeps. However, in the larger geothermal steam areas, there have been efforts to apply the most modern geological and reservoir engineering principles in order to define the reservoir parameters, particularly those relating to estimates of reserves and future productivity. This paper is concerned with the development of appropriate equations and techniques to facilitate these estimates. Production of natural steam or hot water presents problems different from those experienced in the production of oil and gas. For example, steam or hot water systems may be essentially single-component systems, while hydrocarbon systems are most frequently multicomponent fluid systems. Heat effects are much larger for water than for hydrocarbon systems; and the natural steam production may or may not be isothermal, while production of petroleum reservoirs is considered normally to be isothermal. Petroleum reservoir engineering principles may be applied to natural steam or hot water reservoirs if the inherent differences in the systems are considered. The basic considerations involved in geothermal steam reservoir engineering are: thermodynamics, physical and thermal properties of water, materials and energy balances, fluid influx, and performance matching and predicting. Thermodynamics Fig. 1 is a pressure-temperature diagram for the liquid-vapor region for pure water, showing the critical point and five other points representing possible initial conditions for a geothermal steam reservoir. To generate a physical appreciation for the mechanics of natural steam production, it is helpful to consider

Jan 1, 1970

By K. Thirumalai

This study forms a part of Bureau of Mines continuing research on thermal fragmentation of rocks. The potential of internal heating techniques for rock fragmentation is discussed. A concept of rock fragmentation with rapid inter¬nal heating of a localized inner volume of rock is advanced The energy required for rock fragmentation is made available by creating a required vol¬ume of localized heating. The fragmentation of rock using the proposed method is analyzed and qualitatively compared with the results of experiments with Charcoal granite, Dresser basalt, and Sioux Quartzite. High frequency dielec¬tric heating below 100 MHz is used in the study as an example to examine the working of the concept. The selection of operating conditions for the experi¬mental heating is explained. Fragmentation of Charcoal granite and Dresser basalt test rock blocks is achieved for localized heating below 550° C. The heated volume required for fragmentation is observed to be less than 2 percent of the test block volume and the electrical energy consumption is in the order of 3.5 to 6 5 kwhr/m3 The method offers a possibility for in situ fragmenta¬tion of rocks, favorable for internal heating. The method is highly dependent on rock properties governing internal heat generation The efficiency of dielectric heating in the experimental study is observed to increase with increasing dielectric loss of the rock material, ranging from about 10 percent in Sioux. Quartzite to about 50 percent in Dresses basalt

Jan 1, 1970

By S. Akhtar

Interstitial compounds of iron, cobalt, and nickel, and their binary and ternary mixtures with silver, gold, palladium, and platinum were prepared and tested as fuel cell catalysts. The first step in the preparation of the interstitial compounds consisted of preparing finely divided metals. This was done either by the Raney method or by reduction of precipitated hydroxides of the metals. The finely divided reduced metals were then treated with carbon-and/or nitrogen-containing gases to prepare their carbides, nitrides, and nitrocarbides. The materials were tested for cathodic activity towards O2 and for anodic activity towards H2, C3H8, NH3, CO, and N2H4 in acid and alkaline electrolytes at 25° to 90° C in half-cell assemblies. Samples of carbided and nitrocarbided INi-lAg-1Au were about one fifth as active as Pt-black in the reduction of O2 in 35 percent KOH solution, whereas the activities of several interstitial preparations exceeded the activity of Pt-black in the reduction of O2 in 12M KOH containing N2H4. Nitrocarbides of x-Fe2C, 3Ni-1Au, and 1Ni-3Au were effective catalysts for oxidizing N2H4 in liquid NH3 containing NH4SCN. Corrosion of the catalysts by electrolytes was severe in many cases.

Jan 1, 1970