Search Documents

By Bill M. Stewart

Since 1974, a large amount of data has been developed concerning the physical properties and stability characteristics of waste generated by the mining and preparation of bituminous coal. However, very little information has been developed on the properties and characteristics of anthracite waste. During this Bureau of Mines research project, coarse anthracite breaker refuse from five sites in eastern Pennsylvania was sampled and the physical properties, which indicate stability characteristics, were determined in the laboratory. Coarse anthracite breaker refuse is quite similar to coarse bituminous refuse in chemical and mineralogical composition. However, the physical properties of the anthracite waste materials tested are different from those of coarse bituminous refuse. For the coarse anthracite breaker refuse tested, the average maximum laboratory density is 113.2 lb/ft3, the average angle of internal friction (direct shear) and average cohesion are 30.2° and 2.6 psi, respectively, and the average permeability (four sites) is 1.24 x 10-2 cm/sec. Stability analyses were conducted on six theoretical anthracite waste embankments. These analyses show the effects on minimum safety factors of geometry, phreatic surface level, and physical properties.

Jan 1, 1983

By K. J. Ladwig

The Bureau of Mines conducted a field investigation of the water quality in inundated underground coal mines in the Northern Anthracite Field, eastern Pennsylvania. Water samples were collected at multiple depths from nine abandoned mine shafts in the Wyoming Basin, ranging from 68 to 650 m (223 to 2,132 ft) in depth and intersecting as many as seven mined seams in a single shaft. The shafts were also monitored for fluid resistivity, fluid temperature, Eh, and pH using downhole instrumentation. The monitoring program showed that the formerly highly acidic mine water is now slightly alkaline. Sulfate concentrations decreased as much as 74 pct in the flooded workings and 54 pct at a mine water discharge from values reported in 1964 and 1968, respectively. These data are consistent with the inhibition of pyrite oxidation and gradual flushing of oxidation products in flooded mine environments. The monitoring program also revealed significant vertical stratification in water quality in five of the nine shafts, each characterized by two easily recognizable zones. The transitions between zones were sharp, marked by rapid changes in Eh, pH, and ionic composition, the upper zones being less contaminated than the lower zones. The development of stratification appears to be a function of shallow localized flow conditions, arising primarily from the relative positions of mine openings and structural features of the coalbeds.

Jan 1, 1984

By Annie G. Smelley

The Bureau of Mines is testing a dewatering technique for phosphatic clay waste that will recover a portion of the water lost using conventional waste disposal methods and produce solids suitable for land reclamation. The technique utilizes a flocculant, polyethylene oxide (PEO), that forms strong, stable flocs that can be dewatered on a static screen followed by further dewatering on a rotary screen. In field tests conducted in northern Florida, clay wastes containing a nominal 2.5 pct solids have been consolidated to greater than 20 pct solids. The rate at which PEO-treated material continues to dewater in a mine cut also was monitored. Preliminary results indicate that PEO--treated material will dewater to 30 pct solids in 140 days. Pretreatment of phosphatic clay waste with lime and H202 was shown to improve the dewatering technique for problem clay wastes.

Jan 1, 1985

By J. L. Holman

The Bureau of Mines is conducting research to improve technology for the recovery of strategic and critical metals, such as cobalt, nickel, and chromium, that are lost in bulk and particulate superalloy-type scrap because it has not been possible to process mixed contaminated scrap efficiently. The research approach involves melting and casting mixed superalloy scrap into soluble anodes for electrodeposition of Ni-Co alloys by controlled-potential electrolysis. The initial experimental results described in this report are from electrolytic tests us-ing alloy anodes cast from elemental nickel, cobalt, and chromium, the main constituent metals of superalloys. Baseline data and operating parameters are necessary for Ni-Co and Ni-Co-Cr alloys before detailed experiments can be conducted on the more complex superalloy scrap. This basic research assessed the effects of cathode potential, S04:CI electrolyte ratio, electrolyte pH, stirring rate, deposition time, cathode current density, and chromium concentration on cathode current efficiency, alloy deposit composition, and deposition potential at a cell temperature of 55° C.

Jan 1, 1985

By J. S. Hansen

To advance technology that can conserve critical materials, the Bureau of Mines investigated a cast-on hard-surfacing that wear resistance and confines alloy additions to wear-prone surfaces. Wear-resistant material in form is on a polystyrene , the is embedded in a mold of unbonded s and the wear-resistant material is transferred to a cas surface at the time of For low-stress abrasion, derived from high-carbon ferro-chrome had higher wear resistance than did commercially available weld-hard. The microstructure of the was typi-white iron carbides. Free carbon added to the ferrochrome powder produced more M7C3 carbides than did material contained in surfacings made from ferrochrome alone, and improved the wear resistance. Several white iron powders with greatly reduced chromium contents also white iron contain-M7C3 carbides. One derived from white iron powder had wear resistance to that of weld-deposited hard facings. Among the parameters investigated, surfacing thickness was found to have a or influence on diffusion of elements out of the , microstructure, and wear resistance. The results of field tests on bucket-wheel excavator teeth and plowshares with cast-on hard surfacing are given.

Jan 1, 1985

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By A. Visnapuu

Excessive noise and high vibration are inherently associated with equipment used in the mining, extraction, and processing of mineral resources. High vibration degrades structural components, often leading to catastrophic failure and loss of productivity, and excessive noise can result in permanent hearing loss. In order to foster efficient utilization of the Nation's mineral resources and minimize occupational hazards associated with mineral processing, the Bureau of Mines investigated the relationship between the microstructures of carbon and alloy steels and cast irons and their damping capacities (ability to absorb vibration). Researchers measured damping capacity and other properties and investigated the effects of carburizing, spheroidizing, and annealing. The investigators found that in carbon and alloy steels, rounded colonies of fine-grained pearlite in a ferrite matrix correlate well with low damping capacity. Steel microstructures that exhibit sharp-faceted pearlite in ferrite matrix and partially or fully spheroidized cementite in ferrite show considerably higher damping. In cast irons, the lowest damping capacity is associated with nodular graphite microstructure, and the specific damping capacity (SDC) increases as the graphite micro-structure progresses from nodular to compacted to flake. Predominant ferrite in cast irons is also associated with good damping. SDC data are presented for selected carbon and alloy steels and cast irons.

Jan 1, 1987

By S. J. Anderson

To deftne the capabilities of a nonexplosive excavation concept, the Bureau of Mines conducted reduced-scale laboratory tests of a mechanical excavation tool called a rock splitter. The splitter investigated was capable of applying combinations of radial and axial loads to rock when placed in a predrilled hole. Experiments conducted with the tool in concrete, limestone, and granite proved it capable of excavating all three materials. Break geometry in these three materials was the same, which encourages the prediction of performance in all rocks. The design of the radial-axial loading splitter's feather components significantly affected the tool's performance. It appears the design of this in-hole component should be tailored for the rock to be excavated.

Jan 1, 1987

By Richard A. Allwes

This Bureau of Mines report presents a procedure for the design of an arch canopy for use in rehabilitating a high-roof-fall area. Only dy-namic line loading of an unbackfilled arch canopy at its crown is considered, and the procedure does not account for an asymmetrical loading condition. The evaluation of whether an arch canopy is suitable for a particular installation depends on many variables, including in-mine conditions and the engineering properties of the structure. However, a general evaluation can be based on a comparison of the arch's maximum crown deflection and a prescribed allowable crown deflection. The design procedure is based on the concept that when an arch canopy is sub-jected to impact loading at its crown and deflects from its unloaded state to maximum crown deflection, the structure absorbs strain energy, both elastic and plastic. As a result, this strain energy can be calculated from a static load-displacement diagram for the structure. The significance of this design procedure is that it gives mine personnel an analytical tool to select an arch canopy to meet the dimensional and functional requirements of a mine entry and a prescribed allowable crown deflection.

Jan 1, 1987

By Sterling J. Anderson

Through the use of nondestructive testing techniques, the Bureau of Mines is pursuing a goal of improving the efficiency of the rock excava-tion process. Toward this end, 44 laboratory tests were conducted to identify a practical method of monitoring fracture development in rock, as caused by an excavation tool. An acoustic emission CAE) transducer was used to monitor the test samples as they were loaded. The signal from this instrument was recorded in real time along with the radial and axial loads generated by the fracturing device. Through the review of these signals on a common-time base, it was possible to see the relationship between the developing fracture and the loading conditions. As a part of the posttesting investigations, samples that were pletely fractured were sawn and ground to expose the fractures. examination of these samples allowed approximations to be made incom-Visual of the total surface created. Surface area approximations were also made for the completely fractured samples. Quantitative analyses· of the AE signals were conducted for comparisons with the calculated surface areas.

Jan 1, 1987

By D. A. Larson

The Bureau of Mines conducted basic experiments to study the process of crack propagation with a wedge indenter. The work was conducted under plane stress conditions in a hard, brittle limestone. The purpose of these experiments was to first gain an understanding of the basic crack propagation process under a sharp indenter, and second, to determine how the crack propagation process could be used to improve mechanical fragmentation systems. Three methods of rock fracture with the wedge indenter were investigated in this program. These were the confined indentation tests, the unconfined splitting tests, and the edge chipping tests. The confined indention tests represent worst case conditions for crack growth and formed the lower bound on fracture efficiency. The unconfined splitting tests represented best case conditions and fixed the upper bound of fracture efficiency. The edge chipping tests represented an idealized fragmentation process based exclusively upon the highly efficient fracture propagation process. Edge chipping achieved a specific energy of 25 in lb f/in3 compared to conventional drag cutters, which required a specific energy of at least 2,385 in·lb f/in3? Thus edge chipping is up to 100 times more efficient than conventional drag cutting. Because of these promising results, more work is planned with the fracture propagation process in three dimensions.

Jan 1, 1987

By D. K. Ingram

In situ horizontal stresses were measured to determine the influences of geologic anomalies on the regional horizontal stress field in two coal mines in southern Illinois. Stress measurements were obtained near a normal fault having a 121-ft displacement at the AMAX Wabash Mine and a large coalbed want at the Kerr-McGee Galatia No.5 Mine. Horizontal stress measurements were completed using a Bureau of Mines borehole deformation gauge. The average maximum and minimum horizontal compressional stresses at the Wabash Mine were 1,400 and 800 psi, with the direction of maximum stress ranging from N 78° W to N 83° E. At the Galatia No.5 Mine, the averages were 1,500 and 500 psi, with the direction of maximum stress ranging from N 85° E to N 75° E. Generally, the geologic anomalies appear to have no dramatic effect of the regional horizontal stresses. However, subtle differences between stress measurements suggest an influence by the fault zone at the Wabash Mine. The larger anisotropic stress conditions at the Galatia No.5 Mine could be responsible for the increase in kink zones and directional roof failures.

Jan 1, 1988

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By Jon C. Volkwein

The U.S. Bureau of Mines conducted a study to assess the impact of a directional water spray system on a unique single inlet dust scrubber on a low-profile mining machine. Tests were conducted in a full-scale model mine using a continuous mining machine. Tracer gas was introduced at the face and concentrations of the tracer gas were monitored at the face and in the return. Various parameters tested included mining position, depth of cut, brattice setback, and combinations of scrubber, and directional or symmetrical sprays. Results indicated that either water spray configuration improved the ventilation effectiveness of the scrubber by a factor of 2 to 3. Average face ventilation effectiveness (FVE) values for all testing of the scrubber and directional sprays were 0.95, versus 0.37 for a standard 20-ft blowing curtain without sprays. No FVE values were less than the standard 20-ft blowing results.

Jan 1, 1989

By John J. Sammarco

The U.S. Bureau of Mines seeks to increase safety and efficiency in U.S. coal mines. One approach is to develop technology for automation of a continuous mining machine. Realization of an autonomous mining machine requires development of subsystems for machine intelligence, navigation-positioning, and computer control. This report focuses on investigation of one subsystem, an onboard heading system, which would be responsible for determining and controlling machine heading. The onboard heading system investigated is a multisensor system to determine machine heading, pitch, and roll. A directional gyroscope provides heading (yaw), fluxgate sensors provide a compass heading, and gravity-referenced clinometers give machine pitch and roll. The system utilizes a dedicated microcontroller networked to an external system of computers. Tram commands, supplied to the network from external computers, are executed by the onboard system. Sensor feedback is employed for closed-loop control of machine heading by controlling pivots and turns. The report discusses operating limitations and error sources of system sensors and presents test results of closed-loop control of machine heading. Results of tests with a mining machine are used to exhibit various sensor shortcomings and to evaluate control of pivots and turns.

Jan 1, 1990

By N. Kyriazi

The U.S. Bureau of Mines subjected the CSE SR-lOO self-contained self-rescuer (SCSR) approved by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) to a series of laboratory treatments designed to simulate various environmental conditions in underground coal mines. The tests were designed to predict the ability of the self-rescuers to withstand those environmental stresses without causing a decrease in wearer protection. The apparatus were heated to 710 C for 48 h, cooled to -450 C for 16 h, vibrated for 9 h, and dropped 1 m on each axis. A critical concern was internal damage to an apparatus, without any obvious external signs, that would cause it to malfunction or seriously degrade its performance. Carbon dioxide (C02) levels in apparatus with combined treatments were higher than in apparatus with individual treatments and untreated apparatus. The higher levels remained within safe limits, however. None of the treatments caused venting of the small oxygen cylinder that provides starter oxygen. Some bottles were found to be empty because of manufacturing defects in the burst disks. This problem was corrected in later models. The heat treatments did make the case ends more difficult to remove and the breathing bag sticky and subsequently more difficult to unfold. An apparatus that was dropped and vibrated had a broken desiccant bag that released some of its contents which compromised the seal of the relief valve. The case was dented from the drops. As with the first-generation self-rescuers, if there is visible damage to the case of the apparatus, the apparatus should be considered to be internally damaged and must be removed from service.

Jan 1, 1990

By C. W. Whitten

Iron ore deposits in south-central Missouri have emerged as a possible resource for the rare-earth elements. The Pea Ridge Iron Mine is one such deposit. Rare-earth minerals at the Pea Ridge Iron Mine are contained in breccia pipes consisting primarily of silicon oxides and feldspars. These pipes extend up through the magnetite ore body and appear to be alterations and replacement of earlier hematite. The mineralogy of these pipes is very complex and varied, which could complicate the concentration and extraction of the rare-earth minerals. This U.S. Bureau of Mines !eport represents a study by characterization of the mineral phases to assess the amenability and development of concentration and extraction techniques. Previous characterization of rare-earth minerals has been mainly by transmitted light microscopy. This method along with reflected light microscopy, scanning electron microscopy, and X-ray diffraction was used to identify and characterize the rare-earth and associated minerals. The minerals identified were the major ore minerals, magnetite and hematite; the rare-earth phosphates, monazite and xenotime; the rare-earth silicate, allanite; the minor associated minerals, cassiterite, pyrite, and apatite; and the gangue minerals, feldspar, quartz, and actinolite.

Jan 1, 1990

By Stephen C. Tadolini

The U.S. Bureau of Mines has developed ultrasonic measurement instrumentation capable of measuring strains and elongations on tensioned and untensioned mine roof bolting systems. This report evaluates the pulsed-phase-lock-loop and pulse-echo systems. The pulse-echo systems measure time of flight of a signal through the bolt. The ultrasonic instrument converts the measurement into elongations or stress. The most recent Bureau instrument development converts travel-time measurements directly into elongation, load, stress, and torque by simple data manipulation from the keyboard. Bolt preparation and instrument calibration are described in detail.

Jan 1, 1990

By Thomas M. Barczak

This US. Bureau of Mines report examines the roof and floor contact pressure provided by the interaction of a shield with the surrounding strata. Controlled forces were applied to an 800-ton two-leg shield in the Bureau's mine roof simulator; the distribution of forces acting on the canopy and base of the shield were measured with 24 hydraulic pressure cells. Several influential factors that affect the load distribution were investigated: (1) the magnitude of loading (leg pressure); (2) the profile of the canopy, principally the upward-sloping tip; (3) the base-lifting device; (4) horizontal load acting on the shield; and (5) compliancy of the immediate roof and floor. It was concluded that the shield does not develop full canopy or base contact without deformation of the strata. Maximum contact pressures are developed at the rear of the canopy and on the toes of the base. Less than 10 pct of the available shield capacity is developed at the canopy tip despite the design intention to ensure tip contact. Horizontal loading reduced the toe pressure acting on the base by as much as 75 pct. The base-lifting device exaggerated the inherently high toe loading, increasing the contact pressure by more than 200 pct.

Jan 1, 2010

By F. M. Boler

The U.S. Bureau of Mines conducts research at the Galena Mine, Wallace, ID, with the aim of mitigating the effects of rock bursting. Destress blasting is commonly used as a stress control technique at the mine. A digital seismic array and an array of borehole pressure cells (BPC's) had been installed near the site of a stope undergoing mining and periodic de stressing. The instrumentation was being monitored at the time of a destress blast of the 46-99 stope. No significant seismic events occurred coincident with the destress. However, the destress was followed by a 2 ½ -week period of increased seismic activity, including two damaging events on February 7, 1990, at 034500 (hour, minute, and second) and 122020 Pacific standard time. BPC measurements indicated coseismic ground pressure changes on the order of 200 to 300 kPa associated with the damaging events. Fault plane solutions and dislocation models established that stress changes induced by the event at 034500 may have been significant in promoting the occurrence of the event at 122020. Theoretical investigations suggest that applying knowledge of the existing stress field, an understanding of rock burst mechanics, and fracture mechanics principles can improve destress effectiveness.

Jan 1, 2010