Search Documents

By Jose R. Hernandez-Aguilar

"Three models to predict the effect of bubble size (Db) on metallurgical response were tested in a pilot-scale flotation column at Teck Highland Valley Copper mine. The column was fed with slurry collected from the Cu/Mo separation circuit. The first model was the one developed by Gorain et al. (1997), which assumes that the collection zone rate constant (kc) is inversely proportional to Db. The second model was the one proposed by Hernandez-Aguilar et al. (2010), which considers kc as an inverse square function of Db. The third model was the one developed by Yoon and Luttrell (1989) which provides expressions to describe the efficiency of particle collection (E) based on first principles. The results showed a significant bias between experimental and predicted data using the model of Gorain et al. (1997), possibly reflecting the model’s inability to explain the impact of bubble size, bubble rise velocity and flow regime on E. The model of Hernandez-Aguilar et al. (2010) well described the experimental evidence. The model of Yoon and Luttrell gave accurate and unbiased predictions. However, Yoon and Luttrell’s approach calls for a criterion to determine whether the flow regime is potential or intermediate, a subject that requires more fundamental research.INTRODUCTIONParticle collection, i.e., bubble-particle collision followed by attachment, is the basis of flotation. In a quiescent environment (such as the one observed in a column, or away from the impeller in a mechanical cell), a collision event can take place as long as the “degree of turbulence” caused by the rising bubble does not prevent particle and bubble to flow in close proximity. Upon collision, the particle slides on the bubble surface for a period of time. If the particle is hydrophobic, attachment occurs when the “sliding time” is longer than the “induction time”, which is the time required to thin and rupture the intervening liquid (usually water) film forming a three-phase contact angle. While the induction time is largely influenced by the degree of hydrophobicity of the particle, the degree of turbulence is governed by the bubble size. Generally, direct control of bubble size is not exercised by most mineral processing practitioners, in spite of its obvious importance. Studies to model the effect of bubble size on particle collection using fundamental approaches have been conducted (e.g., Anfruns and Kitchener, 1977; Webber and Paddock, 1983; Yoon and Luttrell, 1989; Dai et al., 1999). However, these models have been validated under highly idealized laboratory conditions (micro-scale experiments using single minerals and uni-sized bubbles), far from resembling those existing in practical industrial applications. Fundamental studies to interpret the effect of bubble size on particle collection in industrial environments are largely absent in the literature. Partly because of this lack of practical knowledge, many mineral processing practitioners perceive laboratory “bubble size” studies to be valuable academic exercises, but not something that can be directly applied to daily production issues."

Jan 1, 2011

By Leandro Wiltemburg Araújo

Em Conformação sob Fluência com Envelhecimento, do inglês Creep Age Forming (CAF), o material previamente solubilizado e temperado é carregado elasticamente (normalmente por flexão) e subsequentemente aquecido à temperatura de tratamento térmico de envelhecimento. Basicamente, a conformação se dá por meio de deformações provocadas simultaneamente pela tensão aplicada ao longo do tempo (fluência) e endurecimento por precipitação (envelhecimento). Sendo assim, pretende-se avaliar os efeitos dos parâmetros mencionados no retorno elástico, como tempo, temperatura, retorno elástico e propriedades mecânicas. Portanto foi avaliado, a variação do retorno elástico (springback) em função do tempo para a liga de alumínio AA7475 submetida a um carregamento de flexão durante o envelhecimento realizado em duas temperaturas diferentes (120°C e 150°C). Foi possível observar que quanto menor o tempo e a temperatura de envelhecimento, maior o retorno elástico. Portanto, quanto maior o retorno elástico da peça, mais próxima ela estará do seu formato original antes da conformação [1]. Em relação à dureza, foi observado que quando o material é submetido a uma temperatura de 120°C obtém-se um aumento significativo de dureza Vickers com o passar do tempo (atribuída a precipitação refinada) e a 150°C não ocorre esse aumento significativo dessa propriedade mecânica (atribuído a precipitação mais grosseira).

Aug 16, 2017

By Zay Jeffries

EACH generation accepts the developments of the preceding generations without full appreciation of the difficulties that had to be overcome or of the effect of any given development on society. Today, the production of pig iron is the yardstick with which general industrial health and progress are measured. So natural and logical does this seem to us, that it is difficult to picture conditions prior to the fourteenth century when pig iron was unknown. Not only was pig iron unknown but iron or steel could not be melted and poured into castings; all iron and steel articles were forged from sponge iron. All castings, as well as many worked articles, were made of non-ferrous metals or alloys. In many parts of the world, over long periods of time, not only was the annual exchange value of non-ferrous metals greater than that of iron and steel, but their combined tonnage was greater. At present, the value of the pig iron produced in a year is of the same order of magnitude as that of all non-ferrous metals combined; the tonnage of pig iron is, however, about twenty times that of all non-ferrous metals combined. Owing to lack of records, we will probably never know the relative importance of the various metals at all periods in historic times. A certain conclusion is that the iron and steel industry, since the discovery of pig iron and the cheap methods of converting it into steel, has grown at a much more rapid rate than the non-ferrous metal industries. Notwith-standing their fundamental fitness for man's needs, iron and steel owe their importance in no small degree to the low cost of production. The low cost was a result of increased knowledge of the production appliances and of the metallurgical processes. This increased knowledge is the key to our modern industrial civilization.

Jan 5, 1924

By M. du Toit

Cromanite?is a new high-strength austenitic stainless steel developed by Columbus Stainless. It contains approximately 19 percent chromium, 10 per cent manganese and 0,5 per cent nitrogen. Cromanite can be welded successfully, but due to the high nitrogen content of the base metal, certain precautions have to be taken to ensure sound welds with the desired combination of properties. Although no matching filler metals are currently available, Cromanite can be welded using a range of commercially available stainless steel welding consumables. Welds produced using E309L, E307, E307Si and E312 filler wires are resistant to hot cracking and the formation of nitrogen-induced porosity, but the hardness, strength, ductility and toughness of the welds are generally inferior to those of the base metal. In applications where full use is made of Cromanite?s high strength, welds with matching strength levels would be required. In wear applications, where Cromanite is used primarily for its work-hardening properties and corrosion resistance, lower strength welds would probably be acceptable. Welds produced using E307 filler metal demonstrate the best combination of properties for use in wear applications. The welds display high rates of work-hardening that would result in increases in hardness and strength when subjected to abrasive or high impact environments.

Jan 1, 1999

Implementation of Fine-Screening in Preparation of KGHM PM SA Sandstone-Carbonate Copper Ore for Flotation

Sep 13, 2010

By Kenneth Eilerts

[The development and operation of ?combination on wells?5/ have created new and unusual problems, many of which cast to solved only if information is available concerning the properties of the fluids produced. Data as to the characteristics of the fluids at the relatively high pressures that exist in the reservoirs are especially important, and there is growing economic concern to know what part, if any, of the liquid recovered at the surface was liquid in the reservoir, As an extension of this problem, it is important to Know whether liquid will be formed in the reservoir it as a result o a isothermal retrograde condensation when the reservoir pressure is reduced. The pressure range of such condensation, if it occurs, is significant in the design of gas-recycling plants for maintaining reservoir pressures. In connection with the operation of such plants, it is particularly important to know how gyres sure and temperature will affect the yield of the liquid phase and the composition of the gas to be returned to the reservoir. It has not been possible to predict the behavior of these fluids that have high ratios of gas to liquid by comparing them with the behavior of low gas-liquid ratio fluids at identical pressures and temperatures. Such comparison fails because the proportions in which a component will be distributed between the phases of a system at any given temperature and pressure depend increasingly on the composition of the mixture as the critical temperature and pressure of the oysters are approached. Because many combination wells are producing from reservoirs that have temperatures near the critical point, experimental date on the properties of the fluids under reservoir conditions are particularly important at this time. To rest the immediate requirements of the industry for such experimental information an equilibrium cell has been constructed at the Petroleum Experiment Station of the Bureau of Mines, Bartlesville, Okla. When adequate experimental date, have boon accumulated, it may be possible to mare dependable estimates of the phase relations ft. high gas-liquid ratio fluids at the pre runes and temperatures characteristics of ?combination-well? reservoirs.]

Jan 1, 1940

By M. Jaffe

The data developed in this study establishes the technical and economic feasibility as well as the improved health and safety characteristics of a novel mining concept. The mining concept is a modified longwall technique using prestressed tendons for roof control, longhole blasting for fragmentation, and remote mucking. The technical feasibility was found to be dependent on the state of the art, while economic feasibility was found to be dependent on particular minerals and on supply and demand. Since these two conditions are not necessarily coincident in time the data is presented in the report in a manner that enables the mining engineer to perform a rapid preliminary technical and economic analyses for a specific property.

Jan 1, 1977

By David Winter

The geotechnical design, construction, and monitoring aspects of a tied back excavation 85 feet deep in Seattle, Washington are presented. The excavation was completed in overconsolidated deposits of sand, silt, and clay. Lateral soil pressures used in shoring wall design were the lowest to date for an excavation of this size in Seattle. Instrumentation data collected from hydraulic load cells and inclinometers were analyzed and are discussed. The data suggest the actual soil pressures felt by the wall were lower than the design values. Recommendations for future study, as well as future design modifications are given.

Jan 1, 1987

By C. A. Rowland

With the rapidly rising cost for electrical energy and the long range pre¬dictions for continued rising costs and even possible energy shortages, operation of rod, ball, autogenous and partial autogenous grinding circuits to efficiently utilize the power delivered to the mills will be demanded. This calls for a method to evaluate grinding circuit performance that is accurate, reliable and readily usable as an operating tool by supervisory, technical and operating personnel. Neither the Rittinger and Kick theories of comminution,(1) which preceded the Bond Theory by more than 50 years, had a mathematical means that could be used to predict and evaluate the performance of crushers and grinding mills used to comminute ores and rocks. This severly limited the practical use of these two theories, which were contradictory to each other. They have been superseded by the Bond Third Theory of Commnution.(1)

Jan 1, 1976

By John C. Machisak

INJURY and employment figures for nonmetal mines and mills in 1959 are presented in this publication. Data for nomnetal mines are presented separately from those for nonmetal mills. The Bureau of Mines is authorized to send questionnaires to the nonmetal mining industry each year requesting their voluntary submission of injury experience and employment data. The voluntary response to these requests has contributed greatly toward the promotion of safety in the industry, and every effort has been made to make the information as complete as possible.

Jan 1, 1963

By Erwin L. Zodrow

"The neglect of including the toxic metal mercury in the list of escaping elements (Zodrow, CIM Bulletin, September 1982, pp. 138-140) was pointed out to the author in a private letter by J.E. Rehder, dated September 21, 1982. I welcome this opportunity to present my preliminary mercury research data based on coal investigations supported by N.S.E.R.C and the University College.As mercury is a volatile element and liquid at room temperature, special analytical techniques are required to determine concentrations in whole coal. In the investigation, the coal is analyzed by flameless atomic absorption with a lower detection limit of approximately 10 parts per billion, which, however, is a function of the ash contents of the coals (personal communication, J.L. Brooker, XRAL, 1981).Coal seams of the Sydney Coalfield studied so far include: the Point Aconi, a thin shaly coal, the Upper Bonar, an overrider of the Harbour seam, and the Harbour, Shoemaker and McAulay seams, all of which are shown in stratigraphic succession in Figure 1. The seams have been channel-sampled taking 15-cm coal intervals as one sample for analysis. One channel sample has been investigated from each of the seams listed (two channels were taken from the Point Aconi seam), resulting in 38 samples. Table 1 shows the results, which include mercury contents, ash and total sulphur per sample interval. Figure 2 is a frequency distribution of the 38 determinations."

Jan 1, 1982

By M. Schmidt, P. Nord, M. Larinkari

Cathode stripping machine technology has been developed significantly both in electrorefining (ER) and electrowinning (EW) applications in the last ten years. The main driver has been robotic cathode handling, which has enabled increased flexibility to meet different layout and material handling requirements for both ER and EW processes. Additionally, cathode stripping stations have been continuously developed to optimize speed and to reduce mechanical stress of permanent cathodes. 'taco' type cathodes have been proven as beneficial approach for high capacity operations (particularly in Cu ER), where over 600 cathodes per hour continuous throughput has been achieved. However, the latest developments also apply to split type cathode stripping. Besides material handling, the modern cathode stripping machine has also an important role to provide information for production and quality monitoring. This paper describes the latest developments from the field of copper cathode stripping based on several different projects implemented in the recent years. INTRODUCTION After introduction of the permanent cathode technology in the late 1970s, it became the prevailing technology in copper refineries over the traditional starting sheet process by the end of 1980s. The main driver was less labour-intensive production due to fewer processing steps required along with more automated electrode handling equipment (cathode stripping machine, anode preparation machine, anode scrap washing machine and tankhouse cranes). Since then the design of the cathode stripping machine has followed the development of permanent cathode technology. The main development steps so far can be summarized as follows: Full Deposit Stripping Machine (FDSM) based on waxed permanent cathodes or cathodes with bottom edge strips resulting in split cathodes (copper sheets separated, see Figure 1) Wax less cathode stripping based on V-groove on bottom of the edge strip resulting in either ‘taco’ cathodes (enveloped copper sheets, see Figure 1) or split cathodes Full Deposit Robotic Stripping Machines (FDRSM) using 1–5 robots for permanent cathode handling and cathode stacking.

Jan 1, 2019

By S. Kitamura

In recent years, the amount of ferritic stainless steel production has increased. However, the rust formation by the salt spray test was pointed out in the past. At the centre of the circular rust zone, pitting corrosion where water-soluble nonmetallic inclusions were embedded was observed. These inclusions originated from the suspended refining slag and consisted of multi-phase oxides and sulphides. By the experiments and thermodynamic consideration of the water-solubility, not only CaO or CaS, but also lime rich calcium-aluminates or calcium-silicates have shown large water-solubility. The composition of oxide phase in the inclusions was almost the same among the samples from molten steel, slab, or cold rolled sheet. On the contrary, CaS was clearly observed around the oxide in the sample of cold rolled sheet, although it was not found in the molten steel or slab samples. The enrichment of sulphur occurred from the desulphurization reaction of the suspended slag particles in the molten steel and also occurred from the diffusion of sulphur to the oxide inclusions during the heating of the slab. The optimization of refining slag composition has lead to produce the ferritic stainless steel without rust formation. Keywords: stainless steel, rust, calcium aluminates, calcium sulphides, water-solubility, refining slag, composition control of inclusions.

By Charles Merguerian

In medium- to high-grade metamorphic terrains such as found in New York City(NYC), rock mass texture and mineralogy are important factors in predicting TBM penetration destiny. Integration of data from over two decades of traditional field and tunnel mapping suggest that hard-rock TBM penetration in the NYC area depends upon textural, mineralogic, and structural control. The bedrock of NYC consists of many different lithologic units of varying age, composition, texture, and metamorphic grade including many varieties of intrusive rock. In addition, brittle faults of numerous orientations cut the polydeformed crystalline bedrock, producing zones of highly fractured and disturbed ground and high water inflows. Pre-bid compilation of published bedrock data, drill core analysis by geologists to establish lithologic and mineralogic trends, integrated surface geologic mapping along a proposed alignment, and targeted petrographic and geotechnical investigations to characterize the rock mass conditions together constitute an important prelude to successful subsurface bidding and tunneling. A carefully planned program of as-built geological mapping, structural analysis, fracture class mapping, and monitoring of machine performance data provide important information for adjusting to changed conditions. In complex terrains, a clear understanding of the structural geology of any proposed tunnel line is the simplest and most cost-effective method to mitigate losses encountered during TBM tunneling.

Jan 1, 2005

By M. K. Mohanty

One of the main objectives of this study was to evaluate a fine-coal cleaning circuit using an enhanced gravity separator specifically for a high sulfur coal application. The evaluation not only included testing of individual unit operations used for fine-coal classification, cleaning and dewatering, but also included testing of the complete circuit simultaneously. At a scale of nearly 2 t/h, two alternative circuits were evaluated to clean a minus 0.6-mm coal stream utilizing a 150-mm-diameter classifying cyclone, a linear screen having a projected surface area of 0.5 m2, an enhanced gravity separator having a bowl diameter of 250 mm and a screen-bowl centrifuge having a bowl diameter of 500 mm. The cleaning and dewatering components of both circuits were the same; however, one circuit used a classifying cyclone whereas the other used a linear screen as the classification device. An industrial size coal spiral was used to clean the 2- x 0.6-mm coal size fraction for each circuit to estimate the performance of a complete fine-coal circuit cleaning a minus 2-mm particle size coal stream. The ?linear screen + enhanced gravity separator + screen-bowl circuit? provided superior sulfur and ash-cleaning performance to the alternative circuit that used a classifying cyclone in place of the linear screen. Based on these test data, it was estimated that the use of the recommended circuit to treat 50 t/h of minus 2-mm size coal having feed ash and sulfur contents of 33.9% and 3.28%, respectively, may produce nearly 28.3 t/h of clean coal with product ash and sulfur contents of 9.15% and 1.61%, respectively.

Jan 1, 2008

By F. A. Penning

Improved skips, with lightweight cylindrical bodies, have made a significant contribution to advancing mine hoisting technology. New concept skips of aluminum bodies with rubber lining; fiberglas bodies with polyurethane liners have been designed and fabricated for field testing at an operating mine. New design, adjustable guide rollers have shown improved ride characteristics with noticeably less wear. Major reductions have been made in stress levels and stress concentrations. Field experience has shown the practicality of the approach. Guide alignment has been measured using the Guide Alignment Measuring System (GAMS). Analysis has been applied to interpret the data. Field measurements in an operating shaft and a test tower have shown the agreement in data from GAMS and plumb wires. Reproducibility has been demonstrated. The data are useful to realign shafts, to use as s maintenance tool, and to evaluate the maximum safe hoisting speeds. The surveys are made at several hundred feet per minute and the system is self-contained. Dynamics of skip-guide interaction has been analyzed using the computer program SKIP II. The effects of speed, weight, type of guides, kind of misalignment have been studied. Resonance has been demonstrated and factors that eliminate resonance have been identified. Data from the GAMS surveys are applicable to the SKIP II program. Interaction between the hoist rope and the mine conveyance has also been studied. Computer programs and closed-form solutions are presented. Economic impact of lightweight skips is presented for an existing mine and for a new mine. Reduction in rope size has a profound effect when using a lightweight skip for the same capacity. Increased productivity can be realized by keeping maximum rope pull the same while increasing skip capacity. Examples and charts project the significant savings in capital expenditure for new installations.

Jan 1, 1985

The Barmac autogenous crushing mill is one of the most successful new comminution technologies to become available to the mining and industrial minerals industries in this decade.   The Barmac autogenous crushing mill is an innovative Vertical Shaft Impactor which operates in essence like a high intensity dry ore centrifugal pump with the reduction occurring primarily as a result of high velocity rock to rock impact in a fully rock lined crushing chamber.   With applications in a wide range of mining and industrial minerals operations the Barmac autogenous crushing mill presents an opportunity to enhance reduction and liberation whilst providing many cost savings and production increases in new and existing plants.   This paper briefly describes the operation of the Barmac autogenous crushing mill and reviews its benefits.

Jan 1, 1990

By William C. Cooley

A technical and economic study was made of the feasibility of establishing an underground hydraulic coal mine in the Wilkeson-Carbonado coal field approximately 25 miles southeast of Tacoma, Washington. The deposit contains reserves of more than 200 million tons of generally high quality metallurgical coal. It is located in nine seams of minable thickness in a complex, folded and tectonically disturbed set of anticlines and synclines. Typical dip angles are up to 60°, with minable seam thicknesses of 6 to 17 feet. A mine plan was made for a 2 million TPY mine (clean) using two shafts to access the deposit to a depth of 2500 ft. The mining method uses monitor jets to break coal by sublevel retreat mining, fluming to a sump and pumping the minus 0.25 inch coal to the surface and to a preparation plant. The plus 0.25 inch coal is hoisted by skip. Cleaned met coal would be shipped by rail for export. A middlings product would be sold as thermal coal. Assuming a coal price of $48 per short ton (FOB the mine) for the met coal and $35 for the middlings, the return on investment is estimated at 20% after taxes. The many uncertainties about the geological conditions and the specific mine design parameters make the economic analysis and conclusions somewhat tentative. A second mine could also be developed in the eastern section of the reserves to produce 1 million TPY of clean coal and is expected to have similar economics. Recommendations are made for a Test Mine and a Pilot Mine leading to a production mine.

Jan 1, 1983

By George S. Dulikravich

An advanced semi-stochastic algorithm for constrained multi-objective optimization has been adapted and combined with experimental testing and verification to determine optimum concentrations of aJ10ying elements in heat-resistant and corrosion-resistant H-Series austenitic stainless steel alloys. The objective was to simultaneously maximize a number of alloy's mechanical properties. This research will result in a rigorous tool for the design of high-strength H-Series steels and other types of alloys unattainable by any means existing at the present time. Such a material-by-design tool will also be able to reduce or minimize the need for the addition of expensive elements such as Cr, Ni, Co, Nb, Ti, V, etc. and still obtain the optimum properties of an aJ1oy.

Jan 1, 2003

By F. Freme

Coal production in the United States in 2008 reached a record level of 1.06 Gt (1,171.5 million st), according to preliminary data from the U.S. Energy Information Administration (EIA) (Table 1). This is an increase of 2.2 percent, or 22.5 Mt (24.8 million st) above the 2007 level and 7.9 Mt (8.7 million st) above the prior record level set in 2006. Although coal production was higher in 2008, U.S. total coal consumption decreased in all sectors for the year. Coal consumption in the electric power sector in 2008 was lower by 0.3 percent, while coking coal consumption decreased by 2.8 percent and the other industrial sector declined by 3.7 percent. The commercial and institutional sector, that had been called the ?residential and commercial? sector prior to 2008, declined by 0.6 percent in 2008. It is the smallest of all the coal-consuming sectors. (Note: All percent-age change calculations are done at the short-tons level.) U.S. coal exports were significantly higher in 2008, while coal imports decreased during the year. Total coal stocks increased in 2008, as some consumers added to their stockpiles. The coal synfuel industry, which grew throughout most of this decade, disappeared from the scene due to the expiration of the available federal tax credits at the end of 2007. The decline in coal consumption during the year was the consequence of slowing domestic economic growth, particularly in the latter half of the year, combined with the weather conditions in 2008, resulting in lower demand for electricity. Preliminary data show that total generation in the electric power sector (electric utilities and independent power producers, including useful thermal output) in the U.S. decreased in 2008. Coal-based generation also decreased, resulting in a 3.2-Mt (3.5-mil-lion st) drop in coal consumed in the electric power sec-tor. Coal use in the non-electricity sector decreased by 3.3 percent to a level of 72.6 Mt (80.1 million st). The international coal markets in 2008 were the driv-

Jan 1, 2009