Search Documents

By P. J. Rua

The Piedras Verdes copper mine is a new run-of-mine (ROM), heap leach, solvent-extraction/electrowinning (SX-EW) operation located 21 km (13 miles) north-northwest of the town of Alamos in the state of Sonora, Mexico. The Piedras Verdes copper mine is wholly owned by Frontera Copper Corp. (FCC), a Canadian corporation, through its 100 percent beneficial interest in Cobre del Mayo S.A. de C.V. (CDM), a Mexican registered company. The January 2008, minable reserves were estimated to be 193.6 Mt (213 million st) at a grade of 0.36 percent copper. The overall recovery of total copper was estimated to be 61.9 percent. The property has an additional 17-year life and is designed to produce 31.7 kt/a (70 million lbs/year) of cathode copper. Construction commenced in early October 2005. The first copper cathode was produced 12 months later at a total capital cost of $100 million. Elevations at the site range from 150 to 300 m (490 to 985 ft) above sea level. The area has excellent infra-structure in the form of towns, power, water, roads, rail, airfield and access to the deepwater port of Guaymas (Fig. 1). The surrounding area is also famous for its numerous polymetallic (lead, zinc, copper, silver and gold) epithermal veins. Some of these were mined for more than 200 years and provided the wealth on which the town of Alamos was built. The original village of Piedras Verdes was located in the area of the proposed openpit mine and, consequently, it was necessary to construct a new townsite 6 km (3.7 miles) to the south before project development could commence. The new town site (Fig. 2), complete with power and water supplies, roads, sewer system, schools, clinic and recreational facilities, was completed and occupied by 49 families in September 2005. CDM received its remaining permits from the Mexican environmental authorities on Sept. 20, 2005. This enabled the company to proceed with full-scale development. CDM owns or controls 27 mining concessions covering the resource. Surface rights to the Piedras Verdes project were controlled by four Ejidos (communal agrarian and/or ranching societies) and five individual landowners. CDM has acquired all surface rights necessary for its mining operations and associated facilities either through outright purchase or long term lease agreements.

Jan 1, 2008

By Mark Ferra

Flotation is used in mining to produce concentrates of copper, gold and several other valuable ores. In 2017, a copper mine near Globe, Arizona improved their rougher cells productivity using technically advanced electro-hydraulic actuators in the flotation process by enabling excellent tank pulp level process stability. The new actuators controlled the dart valve position to allow pulp to leave the cell. Tank cell pulp level can change due to feed and discharge fluctuations from neighboring tanks. When traditional pneumatic actuators are used, they have sluggish response times and overshoot due to the inherent physical property of air being compressible. Electro-hydraulic actuators have the benefit of hydraulic stiffness to deliver accurate and repeatable (0.1%) dart valve positioning. The froth layer has more opportunity time to maximize mass transfer into the launderer. The results are an increase in copper recovery by 2-4%. INTRODUCTION In 2013 there was an international flotation technical conference well attended by respected flotation specialists for both mining companies and academia. During the technical session a leading metallurgist was discussing pulp level measurement and said that when he was on the cell deck he stated, pneumatic actuators air cylinders stroking up and down. The presenter then claimed with confidence that "I listened to actuator move so the pulp level in the tank was being controlled!" No one questioned his assumption and I can assert that the audience was quite technical and not shy in their critiques of speakers. The flotation community simply believed that the existing pneumatic technology was enough with no alternative. Having a stable flotation cell pulp level is critical to effective copper recovery. Controlling pulp levels in flotation cells is a complex task that includes modulating dart valves in each cell. The use of REXA Electraulic actuators will decrease the process dead time and maintain froth height in a controlled manner, especially from pulp slurry volume fluctuations from neighboring cells. By reducing flotation cell pulp level tank height variation, a copper mine in Arizona has realized a 2-4% recovery improvement by increasing the froth transfer to the launderers in the rougher cell circuits compared to pneumatic actuators. This paper examines the benefits of using an electro-hydraulic actuator to ensure proper pulp level control and reduce the process operational cost. It will focus on actuator positioning the dart valves to maintain pulp level setpoint at a copper mine in Arizona.

Jan 1, 2019

By Pedro Gabriel Bonella de Oliveira

O processo usual para elaboração de aços utilizados na indústria de petróleo e gás é a laminação controlada, porém, não é adequado para fabricação de peças de geometria complexa, como juntas e conexões. Nestes casos, o forjamento é a melhor opção, pois permite maior diversidade de conformação. A produção de componentes por esta técnica exige tratamentos de têmpera e revenimento para obtenção das propriedades exigidas em trabalho. O objetivo deste projeto é avaliar o comportamento em tração e a microestrutura de um aço microligado submetido ao aquecimento a 855, 900 e 1000°C. Modelos termodinâmicos de Kasatkin foram utilizados para cálculo das temperaturas de transformação austenítica. Os resultados mostram que o tratamento realizado na zona de transformação intercrítica favorece a formação de uma estrutura bifásica de ferrita e martensita com maiores valores da tensão de escoamento e resistência máxima à tração. Nos tratamentos térmicos realizados em maiores temperaturas há diminuição na resistência mecânica, porém com aumento no alongamento em consequência de uma estrutura composta de bainita e ferrita acicular.

Aug 17, 2017

Study on Flotation Experiment of Complex Copper-Lead-Zinc Polymetallic Sulfide Ore in High Altitude Area and its Industrial Application

Sep 13, 2010

By C Agreda

The Cushion Blasting Technique applied to solve the high risk case history represented by a 10,704 TM rock locate at 120 M from the hydroelectrical plants of 350 KV each, is described, analyzed and discussed. The generation and distribution of 700 KV produced by two hydroelectrical plants must not be interrupted by any reason, because the 26 district of the province of cajatambo, of the Lima department; would not have electrical power. The search of the best alternative and methodology, the drilling and blasting pattern calculations, charge design and loading, connections and initiations of the 50 blasts are described, analyzed and discussed. Finally, the excellent results from a technical, economical, enviromental and safety point of view of the 50 primary blasts are discussed and emphasized.

Jan 1, 2005

By David E. Nicholas, Steven R. Dismuke, Paul F. Cicchini

The Buick mine, located 195 kilometers (120 miles) southwest of St. Louis in the Viburnum Trend, is owned and operated by Homestake Mining Company. The mine produces lead and zinc ore from a room and pillar mining method at a depth of approximately 335 m (1 100 ft). The Buick orebody typically averages 60 to 120 m (200 to 400 ft) in width with ore thicknesses ranging from 2.4 to 36.6 m (8 to 120 ft). The mine is divided in two; the halves are referred to as the North mine and South mine orebodies. The North mine orebody contains the higher grade ore; however, the developed reserves for the South mine orebody comprise about 60 percent of the total developed reserves for the Buick property. Existing pillars represent one-third of the total developed reserves.

Jan 1, 1986

By S. du Plessis

Nationalization is high on the policy agenda in South Africa. This paper considers the case for nationalizing the local mining sector from an evidence-based perspective, which is derived from theoretical considerations and related to the known features of the South African mining sector and economy. A strong case against nationalization emerges, which can be summarized as follows. The mining sector is competitive and therefore a poor candidate for public ownership. Furthermore, the resources sector does not dominate the South African economy nor does it create the risk of a decrease in the competitiveness of the industrial sector via the unintended adverse impact of an appreciating real exchange rate due to a commodity boom (Dutch Disease). Nationalizing the mining sector will cost the government more than it receives. This is not only a bad idea in itself, but it will limit the scope for distributive policies on the national budget. The contemporary international experience demonstrates the risks of fiscal imprudence. Finally, nationalizing the resources sector will undermine support for those very market-based institutions required to achieve a higher long-run growth trajectory.

Jan 1, 2013

By Steve Kral

The mining industry has waited a long time for the resurgence in commodity prices and demand for its products that it is now experiencing. Base and precious metals prices have reached levels not seen before. Coal prices have also shot up. And there are encouraging signs in the uranium market. China’s nearly out-of-control economic growth is said to be the leading driver for much of this resurgence. But demand for energy, metals and building materials in the United States and elsewhere are also major factors. The result is that expansions and new mines for nearly every commodity are in the works.

Jan 1, 2005

From Sept. 22-24, the Las Vegas Convention Center will be home to MinExpo 2008, the world?s largest mining equipment show that comes along once every four years. Sponsored by the National Mining Association (NMA), this year?s show is on pace to be the largest ever. Nearly 1,300 exhibitors have purchased nearly 55,700 hm2 (600,000 sq ft) of booth space. At the center of it all will be some of the most impressive mining equipment that the industry has to offer. And in the shadows of the massive haul trucks, drill rigs and bulldozers, attendees will be able to see the latest and greatest products including hand tools; the latest in automation and robotics; safety and communications equipment; longwall mining equipment; engines and parts; materials handling and processing equipment and services; pollution control equipment; reclamation equipment and services; computer applications; consulting and financial services and more. While many companies will be on hand to display the tried and true, there will also be plenty of new things to see. ?We anticipate that a whole range of new products will be introduced at the show,? the NMA said of the show that has been called the world?s richest deposit of mining technology, services and products. In addition to the show that will take place in Center Hall and North Hall of the Las Vegas Convention Center, MinExpo 2008 includes a conference program with 20 educational sessions that will tackle the most timely and pressing issues affecting the mining industry. Many of the industry?s top professionals will lead the discussions.

Jan 1, 2008

By Craig T. Jones, Zachary Q. Maassen

"Jet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. Data from projects completed in Toronto and Ottawa is presented where BOS Solutions’ services provided significant savings compared to the traditional spoils treatment utilizing vacuum trucks for spoils disposal. These traditional treatment methods are cumbersome and expensive by nature. BOS Solutions provided an alternative solution that is environmentally friendly and capable of handling full flow to process these jet grout spoils utilizing a tank system paired with centrifuges and flocculation additives to remove the ground soils and grout product from the spoils slurry. BOS’ process produced a clean water for reuse in the project while reducing the overall waste volume by producing a dry, stackable solid that could be hauled to a landfill. Benefits observed by using the BOS process were disposal waste volumes decreased over 30% and at least a 19% reduction on disposal costs.SCOPE OF WORKJet grouting is a method of ground improvement that relies on the erosive capacity of high-speed jets to cut and mix the ground in place with a cementitious grout. A continuous return flow of cuttings, called jet grout backflow or spoils, is expelled to the surface during the grouting process. The backflow, or spoils, is a mixture of grout, water and soils. Traditionally, the spoil would be collected in in-ground pits and allowed to solidify for a few days prior to hauling to a final disposal site. For the projects completed in Toronto and Ottawa, the jet grouting work was performed at street level, in high traffic congested areas, presenting the challenge of insufficient space for the contractors to process the jet grout spoils in the traditional way. At first, attempts were made of using vacuum trucks to collect and haul the wet spoils to an off-site location where the spoils would be allowed to solidify. However, this method proved cumbersome and expensive due to the high volumes of spoils generated daily and the high number of vacuum trucks required to support the jet grouting operations, respectively."

Jan 1, 2017

By Sangseom Jeong, Moonkyung Chung, Junyoung Ko

"Abstract The plugging effect of open-ended piles in sandy soil is analyzed by full-scale field test and plugging measurement. PLR (plug length ratio) measurement data from 144 field cases are analyzed with pile diameter. Based on the plugging measurements, PLR of open-ended piles which have above 1000mm diameter is predicted to be above 0.9. Through plugging measurements, a new empirical method is suggested for quantifying the plugging effect of open-ended piles. The proposed PLR equation is possible to predict the behavior of soil plug in the preliminary design stage. In addition, in order to investigate the behavior of the soil plug of open-ended pile, field load tests are performed on instrumented three piles driven into sand. It is obtained that the resistance components of open-ended pile are separated by double-walled pile system. It is found that inner shaft capacity is developed nearby pile tip. However, upper soil plug did not influence the inner shaft capacity. Also, it is found that all test piles are floating piles and unplugged condition because the sum of inner shaft capacity and outer shaft capacity is calculated about 58 to 76% of the ultimate bearing capacity.INTRODUCTIONIn Korea, a number of huge construction projects such as harbor terminals, offshore grand bridges, and lifeline systems are progress in urban and costal area. In these areas, steel pipe piles are frequently used to support high-rise buildings and heavy weight structures for ensuring structural safety rather than serviceability limit capacity. Also, steel pipe piles are frequently used in civil engineering structures because they have many advantages such as high-load bearing capacity, light weight and outstanding workability. The mega foundations of grand bridges and high-rise buildings are required in geotechnical engineering. Large diameter driven piles are frequently used in several projects.Many specifications such as API, FHWA and AASHTO have been reported as a design guideline of plugging effect, however , the current design method for plugging effect of steel pipe piles are mainly based on the our knowledge derived from observation of the model test or the small diameter pile load test. Therefore, these specifications have limitation to apply the large diameter steel pipe piles.Much work has been done to study the plugging effect by many researchers. Yamahara (1964) reported that soil plug has been modeled as a thin disk element as shown in Figure 1, since the increment of radial strain of the soil plug can be neglected due to high rigidity of the pile compared to that of the soil plug. Klos and Tejchman (1977) reported that the end bearing capacity of open-ended piles was almost equal to that of a closed-ended pile when penetration depth of pile was above 15times the pile diameters by model tests. Paikowsky and Whitman(1990) reported fundamental studies on mechanism of plugging effect in sand. Paik et al. (2003) reported that empirical relations for plug load capacity, annulus load capacity, and shaft load capacity of open-ended piles are proposed based on the model pile tests. As discussed above, much work has been done in the area of plugging effect. But little work has been done to study the plugging effect by full scale field tests."

Jan 1, 2014

By John A. Breslin

The year 2010 will mark the 100th anniversary of the beginning of the research efforts by the U.S. government to improve the health and safety of miners working in the United States. This research began in 1910 with the establishment of the U.S. Bureau of Mines (the Bureau) and it has continued during the past 10 decades, even after the closure of the Bureau in 1996. The research on safer mining technology, formerly done by the Bureau, has now been combined with National Institute for Occupational Safety and Health (NIOSH) studies of miners? health to form a unified federal research program to improve the health and safety of miners. This article describes this research and places some of the accomplishments into perspective with other activities in the U.S. Mine Safety and Health Time Line (insert).

Jan 1, 2010

By C. P. Kelley, T. J. McKeon

Several recent developments in fine screening technology have been implemented at the DuPont Starke, Florida plant allowing enhanced zircon recoveries while minimizing operator requirements and total operational costs. The total design concept came about through the efforts of engineers at Derrick Corporation (Buffalo, New York), DuPont Titanium Technologies (Starke, Florida) and Roche Mining (Carrara, Australia). The use of the Kelsey Jigs for zircon recoveries from the tailings stream requires two wet sizing functions in order to operate properly. The first wet sizing is required on the initial mineral slurry feed to the Kelsey Jig. This sizing is intended to protect the Kelsey Jigs internal screen basket from plugging with nearsize particles, thereby keeping production rates maximized. The second sizing function is intended to recover properly sized garnet ragging material, which inadvertently ends up in the tailings stream leaving the Kelsey Jig. The unique machine design developed by the three partners in this project incorporated both wet sizing functions (protection and garnet recovery) into a single patented high capacity wet screening machine fitted with patented screen surface technology. This screen surface technology allowed for high capacity slurry handling capabilities at separations as fine as 230 microns while experiencing no nearsize blinding and extremely long screen panel life. The high open area urethane screen surfaces utilized in the application typically last 20 to 30 times longer than stainless steel wire surfaces. The stacked machine design minimized total equipment requirements and screen footprint requirements, and reduced power consumption and overall installation costs.

Jan 1, 2005

By G. S. Hansford, C. J. N. Dempers, G. E. Searby, A. W. Breed, M. A. Jaffer

The bioleaching of sulfide minerals involves a ferric attack of the mineral with the role of the micro-organisms being the oxidation of the ferrous-iron back to the ferric form, and the oxidation of sulfur, either via thiosulfate or polysulfides, to sulfate. The kinetics of bacterial ferrous-iron oxidation and the chemical ferric leach kinetics of sulfide minerals can both be described as functions of the ferric/ferrous-iron ratio. The independently determined bacterial ferrous-iron oxidation and chemical ferric-iron leaching kinetics have been successfully used to predict continuous bioleaching operations.

Jan 1, 2000

By Rajendra Singh

Underground depillaring of contiguous coal seams/sections is a difficult problem, which becomes even more complex if the interburden/parting between them is thin. Conventionally, the depillaring with caving of contiguous seams/sections is done in descending order. However, if the parting is thin, the influence of the top sections/seams working over the standing pillars of bottom the sections/seams becomes extremely important for the safety and optimal exploitation of coal. Field investigations were carried out at Nowrozabad East mine where superimposed pillars of the Johilla top section were depillared above the developed pillars of the Johilla bottom section with a 3 m thick parting between the two sections. The competency of the 3 m thick parting (which consists of alternate layers of shale, sandstone and shaly sandstone) was improved by reinforcement (underpinning). The strata control investigations did not show any considerable instability problem of the 3 m thick reinforced parting and pillars of the bottom section due to top section depillaring. On the basis of this field investigation and a laboratory study on simulated models, simultaneous extraction of both the sections, along with reinforcement of the parting, was suggested for the geomining conditions of the Johilla top and bottom sections. Adopting the suggested simultaneous depillaring process, two sub panels of Johilla top and bottom sections have successfully been extracted without any strata control problem. This paper presents this case study along with the results of the strata monitoring conducted to evaluate performance of the underground structures during the field trial.

Jan 1, 2004

Experiment of Improving the Quality and Decreasing the Impurity of Titanium Concentrate in Panzhihua Mine in China

Sep 13, 2010

By S. H. Jason Choi

The Systems Conveyance and Operations Program (SCOP) is being implemented to convey tertiary-treated effluent to Lake Mead near Las Vegas, Nevada. The Reach 3 Tunnel Project is part of SCOP. The tunnel?s planned location along and across the Las Vegas Wash creates challenging tunneling conditions. A number of feasible excavation and initial support methods are being considered during the final design stage. This paper describes how the tunnel construction options were refined based on anticipated tunneling conditions and compatibility between tunnel excavation and initial support methods. A brief description of the most significant characteristics of the anticipated ground conditions is included for the purpose of discussion.

By W. Abdellah

The purpose of this paper is to establish a qualitative method to estimate the risk level (e.g. rating and ranking) resulting from mining activity. Risk is the product of two factors: probability of failure and cost of consequences. A resultant assessment scale matrix is then used to assign a risk index value which is directly proportional to the potential for excavation instability. A case study, the No. 1 Shear East orebody at Vale?s Garson Mine in Sudbury, Ontario will be examined. A three-dimensional, elastoplastic, finite difference model (FLAC 3D) is presented for a mine development intersection situated 1.5 km below ground surface. The developed assessment scale matrix is used to estimate risk index for intersection (2981) located on 5000 level. The results are presented and categorized with respect to risk-index value, probability of instability, cost of consequence, and mining stage.

Jan 1, 2014

By Willem Le Roux

Occupational health and safety is regulated by statute and common law. South Africa has, like many other countries, legislated extensively on occupational health and safety. Despite the body of legislation, the common law continues to play an important role as far as it concerns contractual, delictual and criminal liability. Two major Acts regulate occupational health and safety viz. the Occupational Health and Safety Act, No. 85 of 1993 (?OHASA?) and the Mine Health and Safety Act, No. 29 of 1996 (?MHSA?). The MHSA applies to mines and works as defined and related aspects. OHASA applies to other industries but does not apply to employers and workplaces to which the MHSA and certain matters covered by the Merchant Shipping Act, No. 57 of 1951 apply. See section 1(3) of OHASA. 2 The employer?s health and safety obligations in terms of the MHSA 2.1 Section 2(1) of the MHSA provides amongst others, as follows: ?The employer of every mine that is being worked must: (a) ensure, as far as reasonably practicable, that the mine is designed, constructed and equipped: (i) to provide conditions for safe operation and a healthy working environment (ii) ... (b) ensure, as far as reasonably practicable, that the mine is commissioned, operated, maintained and decommissioned in such away that employees can perform their work without endangering the health and safety of themselves or of any other person?.

Jan 1, 2011

The Bureau of Mines studied available information on the nature and occurrence of potential sources of aluminum in the United States, its Pacific island possessions, and Puerto Rico to obtain data for use in evaluating the production capability and costs of extracting the aluminum from such materials. The quantity, type, and grade of the materials range from 4 billion tons of bauxite, bauxitic clay, and kaolin averaging 33 to 42 percent Al2O3 to nearly 600 billion tons of anorthosite containing only 27 percent Al2O3. Principal deposits of bauxite, bauxitic clay, and kaolin occur in Arkansas, Georgia, Hawaii, and Oregon. Major anorthosite deposits are located in New York, Wyoming, California, Idaho, and Montana. About 11 billion tons of material in deposits of various types of clay, the kyanite group of minerals, laterites, and shales averaging 27 to 30 percent Al2O3 comprise additional resource's from which aluminum some day may be extracted. Material meeting specifications of the study was found in only 22 States and the Pacific island possessions. Utilization of these large low-grade sources of aluminum awaits development of processes that are economically competitive with the Bayer process for extracting alumina from baxuite, which is at present the only commercial ore of aluminum. Changes in economic and political conditions also may play important roles in the eventual development of the potential sources of aluminum.

Jan 1, 1967