Search Documents

By Ihsan Berk Tulu, Mark Van Dyke, Ted Klemetti, Deniz Tuncay

"Longwall abutment loads are influenced by several factors, including depth of cover, pillar sizes, panel dimensions, geological setting, mining height, proximity to gob, intersection type, and size of the gob. How does proximity to the gob affect pillar loading and entry condition? Does the gob influence depend on whether the abutment load is a forward, side, or rear loading? Do non-typical bleeder entry systems follow the traditional front and side abutment loading and extent concepts? If not, will an improved understanding of the combined abutment extent warrant a change in pillar design or standing support in bleeder entries?This paper details observations made in the non-typical bleeder entries of a moderate depth longwall panel; specifically, it explores data collected from borehole pressure cells and roof extensometers, observations of the conditions of the entries, and numerical modeling of the bleeder entries during longwall extraction. The primary focus was the extent and magnitude of the abutment loading experienced due to the extraction of the longwall panels. Due to the layout of the longwall panels and bleeder entries, the borehole pressure cells (BPCs) and roof extensometers did not show much change due to the advancing of the first longwall. However, they did show a noticeable increase due to the second longwall advancement, a maximum of about 4 MPa of pressure increase and 5 mm of roof deformation. The observations of the conditions showed little to no change from before the first longwall panel extraction began to when the second longwall panel had been advanced more than 915 meters. Localized pillar spalling was observed on the corners of the pillars closest to the longwall gob as was an increase in water in the entries. In addition to the observations and instrumentation, numerical modeling was performed to validate modeling procedures against the monitoring results and evaluate the bleeder design. ITASCA Consulting Group’s FLAC3D numerical modeling software was used to evaluate the bleeder entries. The results of the models indicated only a minor increase in load during the extraction of the longwall panels. These models showed a much greater increase in stress due to the development of the gateroad and bleeder entries—about 80% development and 20% longwall extraction. The FLAC3D model showed very good correlation between modeled and expected gateroad loading during panel extraction. The front and side abutment extent modeled was very similar to observations from this and previous panels."

Jan 1, 2019

By Oliver Bowles

Sandstone, a widely distributed siliceous sedimentary rock, is the third most popular building stone in the United States. It is formed by the breaking down of preexisting rocks by weathering, subsequent segregation of the detrital quartz grains into discrete deposits by the sorting action of water or wind, and finally cementation of the quartz sand into a coherent rock. The homogeneity and resistance to weathering of the resultant sandstone make it suitable for exterior construction. Its excellent wearing properties explain its popularity for flagging and stair treads. However, quarrying and dressing methods and costs are adversely affected by the abrasiveness and hardness of sandstone especially as compared to limestone.

Jan 1, 1963

By G. R. Rawsthorne

"The Con-Rycon mine is located on the north shore of Great Slave Lake in the Northwest Territories within the present city limits of Yellow-knife. Development work on the Con property started in 1936, resulting in a mine-mill complex which produced its first gold brick on September 5, 1938. Since that date 5,000,000 tons of ore have been mined yielding 3,000,000 ounces of gold. At present there are 220 employees at the mine.MineThe mine has 1.22 miles of vertical shaft, 41 miles of level development and 10 miles of inclined raises. There has been 1,000,000 feet of diamond drilling in search of ore. The temperature at the 4900 level (4400 feet below sea level) is 68 deg. F.The present mining method is cut and fill. The majority of the ore mined today passed through an internal winze before reaching the main shaft. The long haulage and double handling will be eliminated with the completion of a new shaft presently under construction to the 5800 level.MineralizationThe ore treated today is from the Campbell shear 1vhich is characterized by lenses and veinlets of coarse textured quartz containing some carbonate, sulphides and finely disseminated as well as visible gold. At the lower levels of the mine the arsenopyrite content in the ore is de-creasing with a~ increase in the levels of chalcopyrite and pyrrhotite."

Jan 1, 1974

By M. N. Shetty

LARGE copper whiskers (-100 p) of 11111 orientation were tested in a floor-model Instron testing machine, at liquid nitrogen temperature. (Testing methods will appear elsewhere.) Whiskers deformed by twinning after some initial deformation. A load-elongation curve at the onset of twinning is reproduced in Fig. 1. Twinning was confirmed by taking a back-reflection Laue picture, using a slit colli-mator, which showed distinct splitting of reflections. The tensile stress reached just before twinning is about 1.4 x 107 g per sq cm (-7.0 x106 g per sq cm—resolved shear stress) which drops to 1.2 x107 g per sq cm (-6 x 106 g per sq cm—resolved). This twinning stress is about five to ten times larger than the value for bulk single crystals of copper deformed at 77°K (-106 g per sq cm—resolved). Twinning models based on Cottrell-Bilby's pole mechanism are discussed in detail by Venables.' In the present work a mechanism based on the idea of failure of a Lomer-Cottrell barrier by recombination will be proposed. An L-C barrier may fail either by recombination or by dissociation.3 Fig. 2 provides the necessary information. It shows that the stress necessary to break such a barrier is about 1.8 x 107 g per sq cm by recombination and 4 x 107 g per sq cm by dissociation at 77°K. The twinning stress reached by whiskers is comparable to the stress level required for failure of an L-C barrier by recombination. (Stroh himself points out that his calculations should not be taken too literally.) We consider a segment of the L-C dislocation which has recombined (AB in Fig. 3) over a length to form the total dislocation which then glides in the

Jan 1, 1965

By J Wesseloo and Y Kim, Y Potvin, G Mungur, D Grant

At the previous MassMin conference held in Sudbury in 2012, the authors proposed a new framework going beyond dilution and equivalent linear overbreak sloughing (ELOS) for stope reconciliation in relation to the planned stope design. More specifically, the new process investigates performance outcomes including rock overbreak (OB) and fill overbreak (FOB), rock underbreak (UB) as well as geomechanical and operational aspects such as blasting, fragmentation and other production data.Based on the findings of the original 2012 study, a comprehensive data gathering program has been undertaken involving design and reconciliation data from 43 stopes mined between September 2012 and October 2014 at BHP Billiton’s Olympic Dam (OD) operation. The new database structure was based on four types of data:stope definition and performance datastope geometrygeotechnical parametersoperational parameters.The new database allows a more in-depth investigation of stope performance. It is now possible to quantify and analyse UB and OB performance from each wall individually as well as the crown. In this paper, the influence of several parameters on recent stope performance at OD is analysed. The underlying reasons for stope wall performance outcomes are discussed in this paper.CITATION:Potvin, Y, Grant, D, Mungur, G, Wesseloo, J and Kim, Y, 2016. Practical stope reconciliation in large-scale operations part 2, Olympic Dam, South Australia, in Proceedings Seventh International Conference and Exhibition on Mass Mining (MassMin 2016), pp 501–510 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2016

By J. Daraisme

Société le Nickel (SLN) exploits the Dôme lateritic nickel orebody at its Tiébaghi operations in New Caledonia. The site geology has an obvious bearing on recovery and metallurgical performance, and the controls are extremely complex at all scales: lithology, oxidation-reduction conditions, mineralogy, and multivariate geochemistry. In that context, establishing an adapted recoverable resource estimation method that is efficient and transparent proves an interesting challenge. The method must address the key notions of: ? Support effect: the exploration data-set can only warrant the estimation of large panels 20×20×3 m3, which are much larger than the selective mining units (SMUs) of 5×5×3 m3 ? Information effect: the selection at production stage uses estimates based on information much denser than that available for mine planning. The problem is rendered more complex in this type of deposit by the fact that the additive variables used for any estimation process (metal accumulation and ore tonnage) are not the ones used to establish the selection at mining stage (i.e. the nickel grade of SMUs, which is the ratio of accumulation on tonnage). Eventually, the selection criteria involve not only Ni grades but also other constituents such as Al2O3, Fe2O3, MgO, and SiO2. The solution presented in this paper is the construction of a platform of SMU multivariate simulations in the saprolitic horizon, together with efficient post-processing aimed at producing the multivariate recoverable resource estimates. The efficiency constraints imposed by the number of blocks to be simulated (1.5 million) lead to resorting to direct block simulations. The underlying multivariate discrete Gaussian model (DGM), the validity of which is tested beforehand, is put to good use to mimic the selection process at the mining stage, by offering the ability to simulate in each block a composite value located at random within the block. Finally, the paper presents the application of a scenario reduction algorithm to pick a representative subset of a few simulations to help appraise the risk attached to the downstream phases (reserve optimization, mine sequencing) of the project. The implementation presented here is for the first generation of the Scenario Reduction plugin built in Isatis software, where measuring the distance between the initial set of scenarios and the reduced set is based on Ni quantities only. Research is under way to adapt the measure to the true multivariate nature of the problem.

Jan 1, 2014

By Zhan Jing

Keywords: thermodynamic, Ni-Co alloy powders, composition, fibrous The mathematics model of Ni(II)-Co(II)-C2O42?-NH3?H2O-H2O of thermodynamic equilibrium system has been developed theoretically according to the law of conservation of mass and the law of simultaneous equilibrium, and the logarithm concentration-pH (log[Me2+]T-pH) diagrams of this system have been made. The effect of ligand and pH value was studied. Two issues in coprecipitation route to synthesize fibrous nickel-cobalt alloy precursor powder, com-position and morphology which are a first priority, are addressed based on thermodynamic analysis and experiments. The results show that suitable pH value range of coprecipitation of nickel ions and cobalt ions in theory can be obtained to maintain fibrous, excellent compositonal homogeneity and stoichiometry in coprecipitation products. Experimental demonstration is also carried out.

Jan 1, 2005

By J. -P. Saindon, L. D. Nel, A. E. Hall, S. G. Hardcastle

"This paper reports on an investigation into gas and dust concentrations in Ruttan Mine's exhaust air. The values obtained indicate that there is excellent potential to recirculate approximately 25% of the hot exhaust air into the intake air to reduce winter heating costs. Contaminant concentrations vary significantly during the course of the working shift and decrease in the mine exhaust system as the air returns to surface. A proposed on-line control system is outlined which would permit recirculation to be implemented with a pay-back period of less than two years. IntroductionIncreased energy costs and depressed mineral prices have resulted in mines, which use winter ventilation air heating, reviewing their systems to try to reduce costs. Heating costs can be significant, for example, Potash Corporation of Saskatchewan spends an average of $580,000 per mine per year and Ruttan mine spends approximately $IM per year on propane for its direct-fired heating system.Several method s of reducing heating costs have been considered and the following have potential application.Heat Exchange Between Exhaust andIntakeThis is usually accomplished by run-round glycol systems. The system is limited by ice formation on the coils in wet exhaust air and by the low exhaust air temperature, usually l0ºC. It also requires close proximity of the intake and exhaust airways to ma~e the cost of the connecting pipeline and pump systems economic . A feasibility study by Inco's Thompson operation reported that a proposed system of this type had a 19-year payback period and was, therefore, uneconomic. Potash Corporation of Saskatchewan is currently investigating plastic heat exchangers for a trial system because of corrosion on metal exchangers. It has the advantage of a 17°C exhaust temperature and relatively dry exhaust air.Waste Heat ReclamationThe waste heat from compressors and hoists can be used for heating in some mines. The feasibility of such a system depends on the individual layout and the proximity of the heat source to the inlet airway. Other mines have considered using the exhaust air in greenhouses to provide a cash crop."

Jan 1, 1988

By Steven Putt

Seismic While Drilling (SWD) is a newly developed technology in the mining industry. Improving upon Measurement While Drilling (MWD) systems, SWD measures mechanical properties of the rock at incremental depths down a blast hole at a much higher resolution. SWD is also immune to common failures and inconsistencies of MWD such as operator and drill specific variation. Seismic While Drilling records the velocity and elastic modulus of the rock with centimeter accuracy in real-time. These properties measured while drilling blastholes are then used as a proxy for density which can be used for: • High resolution geologic modeling • 3D ore control • Drill and blast optimization • Drill to mill tracking One of the distinct challenges with SWD systems is the sheer volume of information acquired. With thousands of measurements per blasthole, the data can be overwhelming for even an experienced engineer. To overcome this complex challenge, the latest cloud computing and analytics models have been simplifying and organizing the data. These newer technologies can amplify an engineer’s capability by delivering actionable insights into their drilling and blasting workflows. The paper presents new results from Datacloud during recent Seismic While Drilling trials in iron ore, metallurgical coal, and hard rock mines around the world. The measurements are compared with wireline geophysical logs, core data, drill cuttings, and conventional measurement while drilling (MWD) systems to validate the technology and show how the data can be used.

By Gaspard Devos

1. A NEW CONTEXT FOR METAL INDUSTRY Producers and owners of industrial extractive sites are living hard times due to Environmental pressure and liabilities. This is valid whatever the region in the world, it is just a question of time. On one hand, the normative environmental pressure is increasing through more severe regulations and controls on all pollution sources and production materials. [ ] Furthermore, more impurities are extracted and captured, more the volume of the related wastes is increasing. But disposal costs are increasing, disposal areas for wastes are restricted, markets for wastes are limited and technologies for waste treatment are, most of the time, not available. On the other hand, for most of the extractive industries, the costs required to get access to refine primary raw material are killing the profitability of the industry. Definitively, a technological and economical breakthrough is ongoing: extractive industries have to increase their feed from secondary material and to be involved more and more with the recycling business.

Jan 1, 2005

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1982

By Raymond W. Henn

The 31th annual short course ?Grouting Fundamentals and Current Practice? was held at the Colorado School of Mines, in Golden, CO June 7-11, 2010. The field demonstration portion of the course was conducted June 10 at wlh Construction Co.?s yard in Denver, CO. The full-scale field demonstration presents many types of drilling and grouting equipment in operation as well as numerous grouting methods performed under various field conditions.

Jan 1, 2010

By Alan: Moore Richards

Effective control of airblast requires that significant factors be identified and satisfied by blast design and careful implementation. Significant factors include charge mass, distance, face height and orientation, burden, spacing, and initiation sequence, stemming height and type, topographical shielding, and meteorological conditions. This paper utilizes case histories of blasting in Australian open pit mines to demonstrate techniques that have been used to control airblast to applicable limits.

Jan 1, 2006

By A. Muwila

Hercules? is a low nickel austenitic stainless steel developed at Mintek that has a typical composition of 9 wt% Mn, 0.05 wt% C, 2wt% Ni, 0.25 wt% N and 16.5 wt% Cr. A more corrosion resistant version of Hercules? (Hercules? B) with 0.5 wt% Mo has also been developed. Potentiodynamic tests performed on Hercules? B in a 5wt% sulphuric acid solution showed it to have improved corrosion resistance comparable to that of AISI 304. The effect of a varying Mn content on the corrosion resistance of Hercules? B has also been investigated and the results discussed in this paper. From the corrosion test results, it is clear that decreasing the Mn content of Hercules? B increased the corrosion rate, while increasing it decreased the corrosion rate. Keywords: austenitic stainless steel, % ferrite, molybdenum, manganese, nitrogen, electrochemical corrosion tests, potentio-dynamic scans, microstructure, chemical analysis.

Jan 1, 2007

In the 1980s and?90s the gold mining industry in South Africa came under pressure from the continued poor dollar gold price and escalating Rand based costs, furthermore the external impacts on the industry were changing. Thus, the Chamber of Mines (COM) shifted its focus away from many historical areas of support towards the new industry challenges in safety and health, labour markets, environmental responsibility, mineral rights legislation and social responsibility. During 1997 the lack of funds and the changes facing the tertiary institutions were often subjects of discussion at the various sub-committee meetings. The Metallurgical Sub-committee of the Chamber Education Fund or the Sub-committee of Consulting Metallurgists as it was known identified the need for the funding structure to change with the times. Up to this time the Chamber of Mines operated an Education Fund that supported mining industry academic departments at various South African tertiary institutions; these funds were derived exclusively from the country?s gold and coal mines the basis of Chamber membership. Funds of less than R5 million per annum were available for distribution by the three disciplinary sub-committees of mining, metallurgy and geology.

Jan 1, 2003

By O. Naiker

Xstrata has modified and improved on the solid state reduction of chromite (SRC) process that was pioneered by Showa Denko in Japan and previously used at Xstrata?s Lydenburg plant. The history of pre-reduction is a long one, with the SRC process being the first and only commercially successful one prior to Premus. Krupp developed the chromite direct reduction and the rotary hearth for the pre-reduction of chromite. However, these processes have not been successfully commercialised. The are a number of significant differences between Xstrata?s patented Premus and the original Consolidated Metallurgical Industries (CMI) process. These include, the use of lower cost anthracite fines as the reductant source together with the use of unactivated bentonite as the binding agent. In addition the use of oxygen as an energy source is used in Premus but not in the original CMI process. There was a fundamental change in the operational philosophy of the process in that while the original CMI process aimed to maximize metallization of the pellets, the Premus process seeks to maximize the energy output from the kiln while still achieving the required efficiencies and hence increasing furnace output. Premus is designed to reduce electrical energy consumption, provide high recoveries of metallic oxides, and utilizes low cost reductant and energy sources such as anthracite and oxygen respectively. Due to the fact that Premus is one of the most technologically advanced and competitive processes used today in the production of ferrochrome it was the process selected for Xstrata?s new ferrochrome facility, Project Lion, that is due to be commissioned in the third quarter of 2006 in the Steelpoort Valley in Mpumulanga, South Africa.

Jan 1, 2007

By Iman G. Ghanad

El presente texto describe un nuevo método para el tratamiento de concentrados de cobre con alto contenido de arsénico utilizando el carbón activado como catalizador. Para ello, se realizaron pruebas de lixiviación con concentrados de enargita de tres minas de Chile, Perú y Estados Unidos, donde los resultados señalaron que la disolución de la enargita fue más rápido con la influencia del carbón en la solución lixiviante, incluso después de haber reciclado el carbón.

Sep 12, 2011

By M. H. Kline

The Cranberry magnetite deposits occur in pre-Cambrian granite-gneiss, in a belt extending from 3 miles southeast of Cranberry, N. C., to about 6 miles southwest of Magnetic City, Tenn. The belt forms a curve) elongated to the north, approximately 26 miles in length. The Bureau of Mines investigation has been confined to the eastern part of the belt, comprising the area from Fork Mountain, Avery County, N.C., to the Hcupscup Knob prospects in Carter County, Tenn. The deposits were worked at least us early as 1820. The Cranberry Iron & Coal Co. and its successors operated the Cranberry mine intermittently for about 50 years until 1930, when operations were abandoned.

Jan 1, 1948

By T. Weatherwax

As part of a strategic research initiative at UBC to design and evaluate integrated underground mining and mineral processing systems, work has been done to determine how to utilize the coarse rejects of pre-concentration in the underground environment. An amenability study for nine orebodies from four of Xstrata Nickel?s Ontario operations evaluated both processing and waste disposal methods. The utilization of the rejects as a high quality backfill with minimal binder requirements has been identified as the preferred disposal method. Fill mixes utilizing the rejects in combination with classified tailings, full tailings, and cement were developed based on the geotechnical properties of the rejects. The mix designs were examined for both strength and rheological properties. The paper will present the results of the pre-concentration testwork, the design and strength testing of various mix designs for rejects from the nine ores and presents a conceptual design for an underground pre-concentration system based on this test work.

Jan 1, 2008

The mineralogy, textures, and genetic significance of a silver-rich siderite vein and an apparently co-genetic galena vein from the South mine, Broken Hill are discussed.Both veins cut sharply across the Main Lode Horizon and appear to be coeval with thc A.B.H. Consols lode.The minerals of thc siderite vein apparently result from the preferential leaching of silver from Main Lode Horizon ore with a demonstrable "breakdown series" commencing with tetrahedrite, passing through silver sulpho-salts, and ending with simple binary compounds or with elemental silver.The siderite vein has been deposited by metahydrothermal fluids along the lines of Schneiderhohn's "secondary hydrothermal" mineralization.

Jan 1, 1968