Search Documents

By Earl R. Maize

Epoxy and polyester-type resins were injected into coal-mine roof strata of the thick Freeport coal seam in Allegheny County, Pa., at test sites in roof that had been exposed several weeks, in newly exposed roof, and in strata over solid coal. Test results indicate that the method of strengthening bituminous-coal-mine roof by injecting a bonding material into the roof strata can be developed into a safe, efficient support system. If roof bonding will become a standardized method of roof support and reinforcement or if it can be effective when used with other types of roof support can be determined only by extensive experimentation in various coal beds. Observations and conclusions are shown at the end of this report.

Jan 1, 1959

By R. H. Seraphim

"Western Mines Limited produces gold, silver, copper, lead and zinc from a number of Paleozoic volcanogenic deposits near Buttle Lake on Vancouver Island. The deposits were emplaced along a series of submarine linear volcanic ridges that extended for at least 6,000 metres in a northwesterly direction.Rock types mapped include: andesitic, dacitic and rhyolitic flow s and volcanic breccias; detrital breccias, tuffs and hematitic silts; black and green cherts; and a variety of dykes and sills, including quartz porphyry and diorite. Orebodies are associated invariably, and in places intimately, with quartzsericite schist and rhyolitic rocks. The ore is complex, varying in mineralogy and tenor both within each deposit and from one deposit to another.Recent studies have increased our knowledge of the structure and left no doubt that the orebodies were deposited both within the throats of the linear vents and on paleoslopes adjacent to these vents.IntroductionWestern Mines Limited operates an 850-tonne-per-day mine, located 85 km south of Campbell River, B.C. The mine is at approximately 400 metres elevation, near the south end of Buttle Lake on Vancouver Island (Fig . I). It has operated since early 1967 and produced 3,650,000 tonnes with an average grade of 1.9 g (0.06 oz) gold, 93 g (3.0 oz) silver, 1.6 per cent copper, 1.0 per cent lead and 7.5 per cent zinc per tonne by the end of 1978. Current reserves are 1,157,000 tonnes of 2.7 g (0.09 oz) gold, 117 g (3 .8 oz) silver , 1.2 per cent copper, 1.2 per cent lead and 8.0 percent zinc per tonne (December 31, 1978).Ore from one zone, known as Myra High-Grade, is mined and milled separately because of its grade. Ore milled prior to December 31,1978, plus reserves, 180,715 tonnes of6.6 g (0.21 oz) gold, 554.5 g (17 .7 oz) silver, 0 .8 per cent copper, 3.2 per cent lead and 10.6 per cent zinc are included in the figures listed in the preceding paragraphs."

Jan 1, 1980

By Stephen C. Tadolini, Peter (Yunqing) Zhang

A unique circumstance created by monitoring a pre-driven longwall recovery room permitted measuring the stresses of a coal pillar throughout its entire life cycle in less than a week. A fender pillar, created in approximately the middle of a longwall panel at a depth of 650 ft, transformed from a solid barrier pillar - to a yielding pillar - to a residual pillar as 3 ft slices were methodically removed with the longwall shearer. The complete transformation, or life cycle, took place in less than 12 hours. The stresses were quickly transferred from the pillar onto the standing pumpable concrete supports and into the outby pillars. Roof to floor closure measurements, combined with the timing of the pillar behavior, provides a detailed look at the uncontrollable convergence of underground mine openings. Pillars remain the most important form of “primary support” and understanding these life cycles is vital for safe and efficient mine design, in both room and pillar and longwall panel extractions.

By Peter White

A bridge reconstruction project involved driving pipe piles for the new foundations. Disturbances within soil layers at depth caused sinkholes to open up within the construction site. After a near fatal accident, the pile driving installations were suspended. The solution involved ground im­provement through cement grouting with sleeve pipes and special grout additives to minimize migration of cement grout.

Jan 1, 1997

Evaluation of Grinding Medium Wear in Stirred Mills The standard fine grinding machines in the minerals industry are stirred mills whose performance largely depends on the competency of the grinding medium. Medium wear in stirred mills is one of the key parameters for medium selection. A wear evaluation methodology is developed and applied in this paper to measure the wear rate of river sand using a laboratory batch stirred mill. The procedure is demonstrated by testing the sand medium in a 0.55 kW batch stirred media detritor (SMD). The sand wear rate determined in the laboratory batch mill is successfully scaled up to that determined on a full-scale Metso 355 kW SMD mill.

Sep 13, 2010

By G. S. Hill, B. J. Huls

This paper on coarse particle recovery (CPR) summarizes a process to capture coarse particles that are not recoverable by regular flotation. Several porphyry copper operations in the world operate analogous circuits that recover non-floated copper from tailings; however, the case presented here is unique in that extensive underlying test work has allowed the authors to elucidate some fundamental principles behind recovery enhancement. This paper discusses an overview of the flowsheet that is proposed to Minera Escondida Ltda., the nature of copper in the feed to the CPR circuit, and the various unit operations within the recovery circuit.

Jan 1, 2006

By Steve Kral

More than 124,000 people involved in the mining and construction industries throughout the world poured into Las Vegas, NV in March for ConExpo-Con/Agg ’99. Show organizers said this triennial exhibition is the largest equipment show in the Western Hemisphere and one of the largest exhibition of any industry. “Clearly, Con-Expo-Con/Agg ’99 was one of the largest trade shows of any industry ever held in the Western Hemisphere,” said Bruno Benna, co-chair of the event. Attendees included mining industry representatives, including aggregates, and sand and gravel producers. In addition, many of the attendees work in the construction, reclamation, forestry, asphalt paving, landscaping and concrete industries. According to show records, about 52% of those attending were company presidents, vice presidents, chief financial officers or managers.

Jan 1, 1999

By W. J. Theron

The purpose of the paper is to give an introduction to the concept of fatigue and its causes in the mining industry. By knowing the fundamental role it plays, together with its dynamics, can positively contribute to a mine?s safety management system. The difference between physical and psychological fatigue will be addressed with a possible range of causes that could trigger fatigue. There are two main sources of fatigue: firstly, work-related fatigue which is associated with activities at the workplace; and secondly non-work-related fatigue. The shared responsibility between the employer and employee is also discussed as it involves factors that occur both in and outside the workplace. Employers have the responsibility to manage fatigue through using a risk management approach. Employees have the responsibility to ensure they get enough sleep, take sufficient and regular nutrition, are healthy and physically fit and come to work fresh and alert. The impact of the implementation of a fatigue management plan and procedures has the potential to eliminate employee fatigue or its causes, reduce the likelihood of fatigue occurring in the workplace, and counteract the effects of fatigue when it occurs. Factors considered when implementing a fatigue management system include: extended hours of work, shift work, time of day and work design. Fatigue is one of the major role players (either causal or contributory) when it comes to causes of fatalities in the mining industry. Our main challenge in identifying whether fatigue played a role is the fact that it cannot be tested in post-mortems like drug or alcohol abuse. It is an aspect worth understanding and getting an organization sensitive to managing it properly to benefit both organizational as well as employee needs. Keywords Signs of fatigue: Causes of fatigue, circadian rhythms, the fatigue equation, fatigue management, fatigue affecting safety, fatigue fighting tips, lifestyle suggestions.

Jan 1, 2011

By Forrest T. Moyer

The overall injury experience, excluding officeworkers, at metal mines and mills during the period 1961-63, reported by operators, was 174 fatal and 11,357 nonfatal disabling work injuries during an aggregate worktime of 451 million man-hours. These injuries occurred at a frequency rate of 25.55 per million man-hours, comprising 0.39 for the fatal and 25.17 for the nonfatal injuries. The combined severity rate of the disabilities was 3,779 days lost or charged per million man- hours, consisting of 2,314 for the fatal and 1,465 for the nonfatal injuries. The average severity of all disabilities during 1961-63, was 148 days per injury. The number of days lost and/or charged, ex- cluding officeworkers, at metal mines and mills during the period 1961-63, was 1,440,000 days charged to fatal injuries and 661,290 days lost from nonfatal injuries. An average of 70,966 men were at work daily. The outstanding cause for fatal injuries was the fall of rock or ore from the back, while most of the nonfatal injuries were caused by handling materials, slips or falls of persons, machinery, falls of rock or ore from back and side, and haulage. Injury experience at primary nonferrous smelters, refineries, and reduction plants during 1961-63, excluding officeworkers, was 23 fatal and 3,214 nonfatal disabling injuries during a total work- time of 277 million man-hours. The injuries occurred at frequency rates of 0.08 per million man-hours for the fatalities and 11.61 for the nonfatal disabilities. The severity rate for all injuries of 1,085 days lost or charged per million man-hours comprised 498 for fatal and 587 for nonfatal injuries. The number of days lost, excluding officeworkers, at primary nonferrous smelters, refineries, and reduction plants during 1961-63 was 138,000 from fatal injuries and 162,385 from nonfatal injuries, An average of 34,938 men were at work daily an active plant days during the three year period. The injury experience for officeworkers at metal mines and mills during the period 1961-63 was 20 nonfatal disabling work injuries, (there were no fatal injuries reported), during an aggregate work-time of 28,694,244 man-hours. These injuries occurred at a frequency rate of 0.70 per million man-hours. There were no fatal injuries reported for officeworkers at non-ferrous smelters, refineries, and reduction plants during 1961-63, but seven nonfatal injuries were reported during an aggregate work-time of 30,814,772 man-hours. The frequency rate for these injuries was 0.23 per million man-hours for this period.

Jan 1, 1967

By Keith R. Vining

Solid fuel, usually coke or anthracite, is commonly added to ground iron ore fines in the pelletising process to reduce the amount of burner fuel required and the maximum firing temperature, while maintaining pellet strength and the productivity of the pelletising plant. However, the use of coke and coal contribute to the production of greenhouse gases (eg carbon dioxide) and are a source of NOx and SOx emissions. Utilising wood biomass / wood char is one methodology CSIRO Minerals is investigating as an alternative to coke and coal, as it is a renewable energy source that is very reactive, has a low ash content and the potential to reduce emissions of greenhouse gases from the iron and steel-making process. Previous work has established that charcoal can effectively replace coke in the sintering process (Lovel et al, 2005), and the following experimental work aims to demonstrate that it can also provide an adequate replacement for coke and coal in the pelletising process. The paper presents the results of an experimental testwork program comparing the behaviour of fired pellets containing traditional solid fuels and charcoal. The physical properties of the pellets are compared in terms of their compressive strength, tumble and abrasion indices and the reduction properties. A qualitative assessment of the pellet microstructures is also presented.

May 1, 2007

By M. R. Geer, H. F. Yancey

"INTRODUCTION Throughout the history of coal washing, the jig has been one of the most important coal-cleaning appliances. In 1935 34.7 percent of the 45,361,021 tons of clean coal produced was the product of jigging. 4/ Previous to 1928, most of the jigs used in the United States were of the piston type, with which sufficient mobility to allow stratification in bed is imparted by the reciprocating up-and-down movement of a piston in the water compartment adjacent to the screen compartment. In 1928, the Baum type of jig was introduces in this country and has since come into wide spread use. In this type, water pulsations are imparted by application and release of compressed air to the water compartment. All prior studies of the mechanism of seperating cleared coal from impurity by piston-type jigs. 5/ The same laws of settling, of course, apply to both types, piston or Baum, but the character of the separation with the Baum type may be modified more easily because of the flexibility with which air may be handled, as distinguished from the fixed action of eccentrics commonly used in piston jigs. Since no detailed studies are available to show the performance, that is, the character of the separation between coal and impurity, of the Baum type the Bureau of Mines undertook the investigation recorded in this report."

Jan 1, 1938

Coal - Surface Mining Coal Preparation Coal Utilization Research and Development Health and Safety

Jan 3, 1976

By R. Stenne

This paper presents the trends in deep foundations in Europe, both in terms of design and construction. Eurocode 7 which is a design code for geotechnical engineering will be introduced in the European Union member countries, and will oblige geotechnical engineers to abandon traditional methods based on a global factor and adopt a new approach based on partial factors of safety. Execution codes (for construction of foundations and other geotechnical processes) are currently being introduced without problems. Ever more demanding environmental constraints push foundation contractors to adapt old techniques and develop new ones to comply with new regulations.

Jan 1, 2000

By Ariane Neves de Moura

As mudanças microestruturais que ocorrem ao longo do recozimento com o aumento da temperatura de recozimento foram observadas no aço inoxidável ferrítico por microscopia ótica. As amostras foram laminadas a frio e recozidas a temperatura de 700°C a 1.000°C, com variação de 50°C. Foram realizadas medidas de tamanho de grão e dureza. Os resultados indicam que o recozimento efetuado a partir de 850°C proporcionou recristalização completa. A maior diminuição da dureza foi observada para a amostra recozida a 800°C devido ao início da recristalização. O tamanho de grão encontrado para as amostras recozidas a 850°C e 1.000°C foi 12,6 µm e 28 µm, respectivamente.

Jan 16, 2018

By Kym Runge, Emmy Manlapig

"The objective of an industrial flotation circuit is to separate valuable minerals from non-valuable minerals utilising differences in their flotation recovery rate. Regrinding and reagent addition are particle modification processes which are employed within these circuits to maximise the flotation selectivity of one mineral with respect to the others present in the ore feeding the process.Batch test nodal analysis, or the ability to compare floatability through mathematical combination of laboratory batch flotation test results, is a powerful technique for assessing the effectiveness of particle modification processes on ore floatability in industrial flotation circuits.In this paper, the use of nodal analysis is demonstrated within an industrial flotation circuit. It is used to show that regrinding and staged reagent addition within Teck Cominco’s Red Dog zinc retreatment circuit is beneficial to pulp flotation selectivity. Optimisation of these processes could potentially improve the zinc recovery within the circuit. Lime addition, which is periodically employed to depress pyrite in the circuit, was found to depress sphalerite in preference to pyrite and to result in poorer metallurgical performance in the circuit.INTRODUCTIONThe objective of an industrial flotation circuit is to separate valuable minerals from non-valuable minerals utilising differences in their flotation recovery rate.Different minerals can only be effectively separated using flotation if they are sufficiently liberated from each other (i.e. do not co-exist within the same particles) and have a sufficient difference in surface hydrophobicity. Size reduction processes and chemical addition are utilised before and within a flotation circuit to achieve sufficient particle liberation and to maximise differences in mineral hydrophobicity. In effect, the objective of these processes is to maximise the flotation selectivity of one mineral with respect to the others present in the ore feeding the process."

Jan 1, 2004

By Larry Schneider

Are you one of the thousands of hunters, fisherman, or hikers who purchased handheld GPS systems over the past several years and then been disappointed in their accuracy and performance. Or maybe you are one of the hundreds of blasters who have attempted to use GPS as a method for locating the exact position of their blast and measure distances from the blast to nearby structures. If so, you may have found that the accuracy of the handheld GPS systems left much to be desired. It may be time to get the units back out of storage and give them another try. As of midnight, May 1, 2000, the federal government has turned off the “error” built into the system known as “selective availability.” Here is a brief explanation of what that means in a question and answer format.

Jan 1, 2001

Ceremonies for the induction of four mining industry pioneers into the National Mining Hall of Fame will be held Saturday, Sept. 13, 2008 at the Charles F. Barber Pavilion of the Museum Convention Center in Leadville, CO. This will be the 21st Annual National Mining Museum and Induction Banquet. The four inductees are Lew Eklund, 76, Carrie Jane Billings Everson (1843-1914), ?Colonel? William C. Greene (1851-1911) and Arthur L. Hawkesworth (1860-1905). Lew Eklund founded Eklund Drilling that is now based in Elko, NV. He invented many designs that play a major role in today?s mining industry. His Cyclo Blower and various sampling devices he designed helped to revolutionize gold deposit exploration by allowing mining companies to effectively sample microscopic gold. Carrie Jane Billings Everson discovered and proved a method for bulk oil flotation concentration of mineral ores, the precursor to modern froth flotation methods of minerals concentration. She patented her process in 1886. In the early 1890s, coworkers built and operated demonstration plants incorporating her bulk oil flotation process. ?Colonel? William C. Greene was responsible for the development of the great copper mining properties of Cananea, Mexico. In seven years, he went from ragged cattleman and adventurer to the greatest captain of industry the borderlands have ever seen. Arthur L. Hawkesworth was a master mechanic for Anaconda Copper. He invented the detachable drill bit. His invention generated tremendous savings for the mining industry in time, in dollars and in safer operating conditions underground. His bit?s long lasting contribution to improved mine economics is immeasurable. The 21st Annual National Mining Museum and Induction Banquet will begin with an open house and reception at 5:30 p.m. followed by the dinner and program at 7 p.m. The inductions will bring to 201 the number of mining ?greats? whose engraved photographs and biographical sketches are installed in the National Mining Hall of Fame.

Jan 1, 2008

By Bill Shand

"Placer Dome - Campbell Mine is a gold mine located at Balmertown in the Red Lake District of North Western Ontario. During the last 50 years, the mine has produced over ten million ounces of gold.A change in ball mill grinding media was made in August 1998 from 1.5” diameter forged balls to 1.5” diameter, 18% chrome balls. This was done to reduce grinding media consumption and to potentially help flotation performance.A marked ball test done in September-October 1999 showed that, of the alloys tested, 18% chrome was the optimum for the ore at Campbell Mine. The test showed that consumption of chrome balls should be 3 times less than forged balls.In December 1999, the ball size was increased from 1.5” to 2” in an effort to reduce the amount of oversize rock discharging from the ball mill. This change in size was successful.Grinding media consumption for the ball mill decreased 73% from 1.20 kg/tonne before the use of chrome balls to 0.327 kg/tonne after the use of chrome balls. This clearly indicates that, for the ore at Campbell Mine, there is significant savings in grinding media by using chrome.Grinding ball costs were reduced by 59% from $O.88/tonne of ore milled to $0.36/tonne of ore milled representing a saving of $298,000 per year. This also clearly indicates that using chrome balls is a benefit at Campbell Mine.Test work to show that chrome grinding media is beneficial to flotation has been inconclusive so far but is still ongoing.No tests have been done to see if there would be a benefit with an even higher chrome percentage in the grinding media. Test work in this area is also planned for the future"

Jan 1, 2001

By Woodcock J. T

During the dissolution of gold in fully aerated cyanide solutions the CN ion is the active agent, and consequently the usual method of evaluating the dissolving power of such solutions is to determine the CN- concentration analytically. The presence in the solutions of copper and/or zinc which themselves form complex cyanides, may result in erroneous conclusions as to the free cyanide ion concentration determined by titration.In this paper the theory of titration of such solutions has been developed, and potentiometric methods have been used to follow the behaviour of complex cyanides of copper and zinc. The results for cuprocyanides show Cu (CN)s to be the most important copper complex, and in addition they explain the reported low rates of solution of gold in copperbearing solutions which when titrated in the usual way, appear to have adequate free cyanide. An explanation of the misleading value of the titration is given, and suggestions for recognition of the condition are offered. Preliminary results for zinc-bearing solutions show that there is no satisfactory end-point for the titration of CN- in excess of that in the complex Zn (CN) 4=, which dissociates to CN and Zn(CN)g-.

Jan 1, 1950

By Arnold M. Lansche

DOMESTIC OUTPUT of white arsenic, As2O3, was derived entirely as a byproduct of smelting arsenic-containing copper ores by The Anaconda Company at Anaconda, Mont., and American Smelting and Refining Company at Tacoma, Wash. Arsenic metal was not produced. Consumption, and Uses.-Most of the white arsenic produced in 1964 was consumed in manufacturing lead and calcium arsenate insecticides. In the 12 year period since 1951 the production of lead arsenate insecticide has varied between 7,800 tons and 4,900 tons, indicating that lead arsenate has maintained its position in competition with organic insecticides.

Jan 1, 1965