Search Documents

Recent data contributions to New Zealand Mesozoic terrane geology confirm the consensus interpretation thatNew Zealand grew by the progressive addition of material by plutonic and accretionary processes along the Gondwana margin. The data also: 1. emphasise the discontinuous but inter-related nature of these processes of continental growth, 2. better establish a direct Gondwana correlation of the Western Province and probable Gondwana provenance of at least some of the Eastern Province, 3. suggest specific times and places when passive or strike-slip rather than subduction regimes are recorded along the south Gondwana margin, and 4. potentially lead to interpretations emphasising parautochthonous rather than far travelled relationships between many New Zealand terranes.  

Jan 1, 1995

By Ian Orford, Peter Radziszewski, Lud Strah

"An autogenous grinding circuit was commissioned at the Brunswick concentrator in October 1998. The AG mill was subsequently converted to SAG operation in May 1999 for a number of reasons. The mill had 48 rows of the NORCAST top-hat integral lifter/liners configured in Hi-Lo mode. A charge motion simulation study, the results of which are the subject of this presentation, was initiated to develop a better understanding of SAG mill behaviour. Using a design of experiments approach, a lifter face angle was determined that would increase mill power draw. Once determined, lifter profiles were modified and installed in July 2001, and a second set installed in February 2002. Resulting changes in mill power consumption are presented.INTRODUCTIONThe Noranda Inc. Brunswick Mine, located near Bathurst, New Brunswick, is a large lead/zinc mine and began milling ore in 1964. The ore is massive sulphide with approximately 20% valuable minerals, 60% pyrite and 20% silicates. In October 1998, an autogenous grinding circuit was commissioned at the Brunswick concentrator (Cooper, Orford, Larsen, 2001).At the time, the autogenous grinding circuit replaced existing surface crushing plants, fine ore storage, rod mills and primary ball mills. The 8.54 m diameter x 4.27 m long (EGL) ANI mill was subsequently converted to SAG operation in May 1999.The mill had 48 rows of the NORCAST top-hat integral lifter/liners and was operated initially with all shell lifters at the same height. Following problems with packing and abnormal wear pattern, the profile was changed to a high-low configuration.Further, it was found that over the life of the lifters, mill power draw and throughput varied considerably. Although a change in mill power draw was expected following lifter replacement (predicted during mill design to be in the order of 300-400 kW), the replacement of the worn lifters with new high lifters resulted in mill power draw decreased by some 1000 kW."

Jan 1, 2003

By Delahant A. B, Dworski M

From the Saranac Laboratory for the Study of Tuberculosis of the Edward L., Trudeau Foundation, Saranac Lake, New York:We are assembled to honor the memory of our friend and colleague, Donald Cummings, one of the founders and a past president of the American Industrial Hygiene Association. I deem it an Unusual privilege to have been asked to give this first memorial lecture and hope that what shall have to say may be worthy of the occasion. It is fitting that we should discuss here the subject of Silicosis to which he devoted such a large part of his life and it is doubly fitting, I think, that I should report to you an extended series of investigations carried on by his associates at the Saranac Laboratory.The subject of silicosis may seem hackneyed to this audience which is so familiar with the tried and accepted methods of prevention and control.But in spite of our efforts, the condition is still with us and unfortunately is still being produced in many places. In industries that now maintain good control of dust, fresh cases are appearing on annual re-examination, whose major exposure date back to the days before the hazard was recognized.A few new employees, with apparently ineffective upper respiratory protection against inhaled dust, develop silicosis precociously in environments that are comparatively harmless to their fellows. In plants that have relaxed their vigilance under the urgency of war production schedules, conditions again prevail that will produce, disease in the future.Silicosis acquired new interest with the announcement by Denny, Robson and Irwin(1) in 1937 that it could be prevented by the inhalation of powdered metallic aluminium. It so happened that without knowledge of their work, we at the Saranac Laboratory had for some months been conducting similar experiments with one of the hydroxides of aluminium.Quite independently we discovered that hydrated alumina would also protect animals against quartz. Our approach to the problem had been empirical; we were trying to neutralize quartz particles by coating their surfaces with an insoluble material following the lead of Kettle who in 1932 had shown that this could be accomplished with iron. He neglected to describe his method and the chemist who prepared his coated...

Jan 1, 1945

By James R. Wait

The present final report constitutes the total productivity of a series of contracts from the U.S. Bureau of Mines and the Institute for Telecommunication Sciences over the period 1971-1979. The emphasis on the research has been analytical. In this "executive summary" we give a succinct description of each phase of the investigation. In the first phase of the investigation that was stimulated by the National Academy of Engineering, we concentrated on the analytical studies of techniques relevant to mine rescue. Several specific procedures for locating a buried source were analyzed. In the next, but overlapping phase of the investigation, we dealt with the fundemental character of how electromagnetic waves propagate in mine tunnels. At the outset we allowed for the finite conductivity of the tunnel walls and the presence of axial conductors such as cables, pipes, and tracks. The third phase of the investigation was devoted to the analyses of various specific geophysical engineering problems. The related fourth phase dealt with the general subject of non-destructive testing of wire ropes such as used for mine hoists.

Jan 1, 1980

Studies of the Main Seam in the Rapahoe Sector of Greymouth Coalfield have shown that the proportions of palynomorphs and palynomorph groups vary vertically within the seam, but remain laterally consistent. Subsequent examinations of other seams in the Rapahoe Sector have demonstrated that the changes in palynomorph proportions observed in the Main Seam are specific to that seam, effectively providing a seam 'fingerprint'. Such a characteristic signature may be used to identify the Main Seam where faulting or seam splitting confuses seam correlation between drillhole intersections. Palynomorph assemblages are derived from the original plants which formed the peat mire, and yield information on mire conditions such as climate, mineral matter input and chemistry. These depositional factors influence coal properties such as mineral content, volatile matter yields and coal breakability. Palynological data can therefore assist in development of depositional lTIodels for prediction of coal quality variations. Several other, thiner seams in the Rapahoe Sector have been demonstrated to also contain recognisable palynomorph assemblages, suggesting that other seams may also possess distinct palynomorph abundance profiles.

Jan 1, 1996

By William A. Beck

"In 1912 bauxite was discovered in the Andersonville district, which lies in the 28th and 29th land districts of Georgia and comprises parts of Sumter, Macon, and Schley Counties. Mining was begun in May 1914 by the Republic Mining & Manufacturing Co. Considerable ore has been produced in this region since that time by individual interests and by the American Cyanamid & Chemical Corp., which acquired the property formerly owned by the Republic Co.The area was examined in the fall of 1941 by representatives of the Bureau of Mines and the Geological Survey, after which a prospecting program was begun by the Bureau. Drilling was started on December 26, 1941, and continued until November 18, 1943. A total of 1,192 holes was drilled in the district, and 3,679 samples were taken and analyzed.Mineral exploration agreements were signed by 146 property owners covering 42,128 acres. Holes were drilled on 121 of these properties, which have a total area of 38,778 acres.Drilling under this project disclosed several new deposits, of which four have been completely delimited. Previous prospecting in this area by mining companies did not find bauxite, as it lies under heavy overburden. Work by the Bureau indicates 14,412,000 long tons of ore containing 30 percent or more alumina. The total tonnage is divided as follows:Georgia State Highway Routes 26 and 4-9 traverse the district. The Central of Georgia Railroad passes through the center of the entire district (see fig. 1).The project was initiated by J. R. Thoenen, supervising engineer, Non-metals Mining Section, Mining Division, Bureau of Mines. It was under his general supervision until July 1942, after which it was under the general supervision of E. J. Lintner and Rowe McCrae, district engineers for Georgia, South Carolina, and Flordia, respectively.John C. Feeley, Jr., was project engineer from December 1941 to April 1942. Other engineers who assisted in the work on the project are R. E. Babcock, T. M. Romslo, Don M. Coulter, and Walter T. Lewiecki.Acknowledgment is due the metallurgical staffs at College Park, Md., and Tuscaloosa, Ala., for analyses of samples and beneficiation tests.Acknowledgment is also expressed to Alfred D. Zapp, M. W. Harris, Elmer Kneedler,and Parke D. Snavely, of the United States Geological Survey, for their aid, data, and maps.Bauxite was discovered in the Andersonville district in 1912 on lot 187 of the 28th land district, in Sumter County. This lot is situated about 1.5 miles west of the Flint River, on the south slope of the valley of Sweetwater Creek. Mining was started in May 1914 by the Republic Mining & Manufacturing Co. This and adjacent properties were acquired in 1930 by the American Cyanamid & Chemical Corp., which has been operating there since."

Dec 1, 1949

By P. R. Tisot

Structural response and/or deformation was determined for each of four different grade Green River oil shales (27.0-, 34.5-, 45.5-, and 63.5-gal/ton) as they were heated in an inert atmosphere, under constant compressive stress, from ambient to subretorting temperatures; that is, below those required for rapid pyrolysis of the organic matter. Small cores and small columns of confined fragments comprised the test specimens, which were heated, in a specially designed microunit, at a uniform rate either to 725° or to 825° F under three different stress levels, 80, 200, and 325 psi. Structural response of some cores was observed as they were heated in a stress-free environment. The obtained stress-strain-time-temperature relationships provide information regarding the oil shale's yield temperature, yield stress, rate of compressive strain, loss of mechanical strength, and nature of structural deformation. Effects of structural deformation on induced permeability in small columns of fragments are presented. Results indicate that underground retorting of Green River oil shale may be seriously impaired through loss of induced permeability brought about by structural deformation of rich oil shale under the influence of heat and compressive stress.

Jan 1, 1971

By G. E. Perry, R. D. Seba

The steam soak process is the most widely applied and most successful thermal supplemental recovery process in use today. This process, which consists of injection of steam in various quantities into a well that is subsequently used as a producer, can be repeatedly applied to the same well. The treatment, if successful, will increase the production rate of the well for a given period. For this reason, the steam soak process should be considered primarily as an acceleration method rather than as a method for producing oil that could not be recovered by primary means. However, application of this process to reservoirs containing viscous crude may produce oil that otherwise would have zero present value or would be produced at such low rates by primary methods that it would not be profitable. A major necessity for the successful application of the steam soak process is a source of natural energy. This source of energy may exist in one or more of the following forms: expansion of fluids, compaction, gravity drainage. This study was undertaken to determine the effect of gravity drainage on steam soak production and recovery and to develop a method for predicting production rates, ultimate recovery, and heat requirements when applying this process to a reservoir in which the primary driving mechanism is gravity drainage. (For additional discussion of some of the factors that affect recovery of viscous oils by the steam soak process, see Ref. 5.) Model The model developed for analyzing the performance of the steam soak process in gravity drainage reservoirs is a modified form of that developed by Matthews and Lefkovits.1,2 The model used in this study consists of two concentric cylindrical volumes of productive formation with cap and base rock of impermeable material. The inner cylinder, extending from the radius of the wellbore to some predetermined radius, is referred to as the hot zone; and the outer cylinder extending from the exterior boundary of the hot zone to the outer drainage boundary will be referred to as the partially heated zone. Fig. 1 is a schematic cross-section of the model, indicating its thermal properties. Horizontally the reservoir is divided into two regions, the upper region having a high gas saturation and residual liquid saturation, and the lower region containing a high liquid saturation. The boundary between these two regions is referred to as the free surface, which drops and changes shape as fluid is produced from the reservoir. The model was used to analyze the steam soak process by applying the following assumptions: 1. The horizontal formation is composed of one or more homogeneous noninterconnected layers containing incompressible fluids. Each layer is treated separately. 2. The hot zone is heated by the initial soak and is maintained at the steam temperature corresponding to atmospheric pressure by resoaking. 3. The height of the free surface at the producing well is at all times zero (producing well is pumped off). 4. The position of the free surface at the start of

Jan 1, 1970

The El Pe±on gold-silver deposit comprises four epithermal, low-sulfidation veins, which contain 2.9 million oz Au and 48 million oz Ag. Provisional data on alteration mineralogy, fluid inclusions, and vein textures constrain the chemistry and hydrology of the hydrothermal system responsible for ore mineralisation at El Pe±on. Alteration minerals include quartz, adularia, albite, illite, smectite, calcite, chlorite, and pyrite. Alteration minerals suggest the existence of near neutral pH, low salinity hydrothermal fluids, which circulated over an area greater than 18 km2. Complex mineral zonation patterns result from variations in host rock permeability and composition, overprinting alteration possibly produced by thermal waters from surficial and peripheral parts of the hydrothermal system, and supergene weathering in the hyperarid environment. Upflow zones were focused along N-S and NE trending structures, producing crustiform quartz-adularia+carbonate veins. Fluid inclusion data indicate vein deposition from low salinity (

Jan 1, 2002

By K. L. Whitehead

An examination of 60 mines, 11 illumination hardware manufacturers, and Q mobile face-equipment manufacturers was conducted to determine the state of the art of mine-illumination hardware, define lighting system installation and maintenance problems, and assess personnel acceptance of lighting. Longwall and mobile face-machine illumination were studied. Major problems on room and pillar installations include damage of exposed components, electrical failures, and reduced lamp life, with extreme variability in the degree of these problems. Most longwall systems had low or moderate maintenance requirements, cable damage being the most significant problem. Most mobile face-equipment operators liked their machines' lighting systems, but many complained of glare and other problems. Longwall lighting was unanimously accepted by face personnel, and most complaints were minor. Based on the survey, general installation and maintenance guidelines have been established, addressing hardware design aspects, approaches proved effective to minimize problems, and improper practices noted which are detrimental to effective lighting.

Jan 1, 1981

Silica reacts with cryolite at 1010°C in two stages. The first stage is the formation of a sodium aluminosilicate of composition consistent with the mineral jadeite (Na20.AI20s.4Si02). The formation proceeds by atleast two different reactions. Formation of alumina or an aluminosilicate proceeds to its limiting value in the first 30 min while the formation of jadeite proceeds at a steady rate until quantitative conversion is achieved after 150 min. The net overall reaction can be expressed by the equation 6 Si02+2 Na3AlF6? (Na20.AI20s.4Si02) +2 SiF4 +4NaF.The second stage involves a slow reaction that proceeds with the evolution of a little SiF4, The net result is the formation of sodium aluminosilicates that are soluble in 30 per cent AlCIs-HCI solutions. While this could be explained by disproportionation of jadeite to form albite (Na20.Al203.6Si02) and nepheline (Na20. AI203.2Si02), it is more likely that it is due to further but limited reaction between the oxides and fiuoroaluminates.

Jan 1, 1972

By W. K. Hitchcock

Anecdotal evidence suggests that re-entering a sealed heating poses a significant hazard, whereby the original heating is rejuvenated at an accelerated rate forcing withdrawal and re-sealing of the area. Bulk-scale laboratory experiments using a two-metre column confirm these mine site observations. A high volatile bituminous coal from New South Wales, Australia was allowed to develop a significant hot spot before being inerted with nitrogen and allowed to cool. Air was then allowed back into the coal after the nitrogen was turned off and a hot spot developed almost immediately at the same location as the original hot spot before it quickly migrated towards the air source within a day. Two more re-entries were simulated. Each successive re-entry developed a broader hot spot and took longer to reach thermal runaway. These results clearly show the behaviour that can be expected when trying to recover a section of an underground coal mine that has been sealed due to a spontaneous combustion event.

Jan 1, 2009

By A Paz, H Lehto, M +stholm, I Roitto

Nowadays, the demand for a finer grind in minerals processing has set new challenges within the industry, particularly for grinding technology. Apart from a finer grind, energy efficiency is also a key driver in optimising comminution technology.Stirred milling technology, already proven in many other industries, delivers a modern, sophisticated, flexible and energy efficient grinding solution for fine and ultra fine grinding in minerals processing. Fine grinding technology is utilised particularly in concentrate regrinding to complete the liberation of valuable minerals after the first stage of concentration. Maintaining the correct particle and particle size distribution of the regrind product is crucial for downstream process performance. Stirred milling technology offers the unique possibility for online control and optimisation of the regrind product particle size. This paper describes the basis of this online control possibility and discusses the implementation of stirred milling technology in minerals processing, particularly in regrinding applications. The paper will also outline management and control of fluctuations in feed rate tonnages as well as particle size fluctuations in concentrate regrinding.CITATION:Roitto, I, Lehto, H, Paz, A and +stholm, M, 2013. Stirred milling technology - A new concept in fine grinding, in Proceedings MetPlant 2013 , pp 190-201 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 15, 2013

By Richard Mcivor, Largo Albert

"Inco Limited has operated aluminum mine shaft conveyances since 1968. Aluminum conveyances are used where the hoisting in system requires lightweight conveyances to maintain the hoist rope safety factors and mine hoist rope pulls as dictated by government regulations. Inco Ltd. currently has 20 skips (including spares) operating in the Ontario Division mines. The main problems encountered are with galvanic corrosion between dissimilar metals and metal fatigue. This paper will highlight some of the problems encountered and illustrate methods utilized to overcome the problems and improve the conveyances performance.IntroductionAluminum mine shaft conveyances have been in use at Inco Limited's various Sudbury district mines since 1968. All of the conveyances currently in use are skips used for hoisting mine ore and rock. Inco had an aluminum quick change Kimberley-type skip and cage in operation at its Totten Mine in the early 1970s, but this mine is no longer in operation and no further comment will be made.The primary reason why aluminum conveyances are chosen over conventional steel conveyances is because of their light weight. Typically an aluminum conveyance will weigh about 60% to 70% of a steel conveyance of similar design. The lighter weight conveyances will allow higher payloads to be used and still maintain the statutory hoist rope factors of safety. It must be remembered that increasing the payload will increase the power required to raise the load and the hoist will have to have the necessary horsepower for the increased payload or the system will be overloaded.The front dump (Rola-chute) skips are of the bail-less design, i.e. the box structure also supports the load and has the shaft guide shoes attached directly to the side of the box structure. The Copper Cliff North Mine and South Mine skips have a joint in the centre of the conveyance and are installed in the shaft in two sections and connected with pins. This feature allows very long (42 ft) skips to be used in areas where a one-piece bail-type conveyance could not be installed. It is not practical to make sectionalized bail-type conveyances"

Jan 1, 1988

By Bryn Harris, Liming Huang, Andre Laplante

"This paper reviews flowsheets generally used in gold rooms to upgrade primary gravity concentrates particularly those of Knelsons. It is concluded that even for small operations, which treat between 250 and lo00 kg of concentrates per day, there is a strong economic incentive to include in the flowsheet magnetic removal of tramp iron, at least two shaking tables, screening of either table feed or table tails at 150-212 um, and scavenging of table tails with a small centrifuge. Headroom, rather than floor space, is often inadequate in most gold room designs, and limits gravity flow and flowsheet flexibility. Experimental data are presented to demonstrate the effectiveness of a small Knelson Concentrator to scavenge significant amounts of gold (up to 91 %) from fine table tails.RésuméCet article examine les schémas d’évolution généralement utilisés pour traiter les concentres gravimétriques d‘or, en particulier ceux produits par concentrateur Knelson. Nous en venons à la conclusion que même pour un petit circuit d’une capacité de 250 A 1000 kg/jour pourrait bénéficier des opérations unitaires suivantes : concentrateur magnétique pour extraire la feraille, au moins deux tables A secousses, criblage de l’alimentation ou du rejet d’une ou des tables i une maille de 150-212 um, et épuisages des rejets fins de table avec un centrifuge de petite capacité. C’est l’espace vertical du lieu où se fait cette concentration qui représente la contrainte la plus importante, plutôt que sa surface, puisqu’il faut maximiser l’écoulement par gravite des pulpes et s’offrir une certaine flexibilité quant à l’agencement final des opérations unitaires. Nous présentons également des données expérimentales pour démontrer l’efficacit6 d‘un Knelson de laboratoire pour récupérer jusqu’ à 91 % de l’or contenu dans les rejets fins de table."

Jan 1, 1999

By J. D. Steenkamp

Keywords: Thermal, conductivity, diffusivity, expansion, history, density, specific heat capacity, industrial rich high-carbon manganese slag The thermal conductivity of slag is an important parameter in the design of furnace-containment systems based on freeze-lining technology. Literature indicates that the crystal content of a slag has a significant influence on its thermal conductivity. Industrial, rich, manganese-bearing slag was cooled at different rates to create samples with different microstructures. The coefficients of thermal conductivity of these samples were measured in a nitrogen atmosphere from room temperature to 990°C at 100°C intervals. The laser-flash measurement technique was used for this purpose. Follow-up investigations included XRF and XRD and modelling in FACTSage.

Jan 1, 2011

By M. Kinnunen

Handling of municipal solid waste (MSW) and control of its potential resources is becoming increasingly important in modern society. The OECD (Organization for Economic Co-operation and Development) average on municipal waste produced in 2003 was that of around 570 kg per inhabitant. In European Union countries around half amount is of MSW landfilled. In Finland still 88% of MSW was landfilled in 2004. Since incineration reduces MSW volume significantly while producing heat energy, it has become one of the most common waste handling techniques. The shortcoming of incineration is however, that incinerated MSW is often not pre-sorted and it produces slags and ashes as side streams from which recovery of metals is difficult. This paper looks into possibilities of scrap metal recovery for recycling from municipal solid waste incineration (MSWI) bottom ash. In order to do that, a flow sheet of physical separation methods was developed and tested with Finnish rotary furnace MSWI bottom ash. In addition, an empirical model for estimation of the recoveries of scrap metals with physical separation methods for treatment of MSWI bottom ash was developed. According to the results of this study, for 1 Mt of incinerated MSW with 30% mass reduction, a minimum resource potential of 100 kt for magnetic metal scrap of roughly 24 % grade and about 19 kt of non-magnetic metal scrap of roughly 65 % grade. In other words, 57 kg magnetic scrap and 12 kg non-magnetic scrap per inhabitant at the mentioned grades, respectively. Although wide variations of parameters affect the MSWI bottom ash quality, it can be said that a considerable amount of metals is drained into MSWI bottom ash. Results of this study show that from MSWI bottom ash significant material streams metal scrap can be reintroduced into the resource cycle which would otherwise be lost.

Jan 1, 2014

A glance at the following chart reveals that because of the continued poor economy, the slump in industrial mineral production continued into 1980. Gypsum was down 17% from 1979; cement down 9%, sand and gravel, 17%, and crushed stone, 11%. All these downward trends reflect the high interest rates and high costs that slowed construction starts. Domestic fluorspar was down 21% and imports off 14% due to the steel iudustry slump. However, potash production was up 8% and phosphate, 5%. Increased drilling activity spurred au increase in barite production of 25%. Most other industrial minerals posted losses with only a few insignificant increases. As expected, prices were higher, reflecting increases due to high costs for labor, supplies, and above all, energy. Increasing energy and transportation costs also had their effect on industrial mineral production. Railroad freight rates increased 16-22% including fuel surcharge; truck rates increased 11-14%a; and ocean freight rates increased 20% for finished goods. The 1979 shortage of boa and hopper cars did not continue into 1980-most likely due to low production of many of the hulk industrial mineral commodities. All in all, 1980 was not a good Year for industrial minerals.

Jan 5, 1981

By R. G. B. Pickering

The purpose of this report is to chronicle the interaction between Anglo Platinum and Sandvik Tamrock during the development and application of Long Hole drilling as a viable, practical method of narrow reef mining. Appendix I identifies the people from Anglo Platinum and Sandvik Tamrock who participated in the project. Experiments in long hole drilling and blasting were conducted in a number of mines during the late 1950s and early 1960s. Some of the advantages envisaged were: ? The face would require no daily examination ? No barring down or immediate face support required ? No sockets to clean ? Only a few well drilled holes rather than large numbers of short blast holes ? Avoidance of poorly-marked holes, inaccurate drilling and improper charging ? Better supervision and better face advance. Holes 50 mm in diameter were drilled parallel to the stope face by pneumatic rock drills from advance strike gullies. Holes were charged with amon gelignite cartridges. All holes were traced with detonating cord to ensure propagation of the explosive along the entire hole length. Rock was blasted onto a rolling scatter pile. A number of reasons have been cited for the failure of this mining method. The two most important were: ? problems in controlling hole deviation which was exacerbated by the fractured ground ? difficulty of charging up holes in fractured ground, due to relative movement of rocks along fracture surfaces over the hole length. The idea of drilling a few long holes parallel to the face rather than a large number of short blast holes perpendicular to the face was an attractive option to mechanize narrow reef mining. This particular project started in 1998. Initial trial The Union Section of Anglo Platinum purchased a Solo H 606 RA long hole drilling rig from Sandvik Tamrock in 1997. In order to evaluate long hole drilling as a basis for face mechanization. The Solo series of drill rig was selected because it combines high drilling performance and good drilling accuracy with high versatility with a compact size. The mining method proposed by a consultant to Anglo Platinum was based on the current trackless mining method practised by Union Section. The trackless mining method is better described as a trackless development and transport method. Reef strike drives were installed approximately 40 metres apart on dip using trackless equipment. Reef was mined using hand-held pneumatic rock drills and scraper winches and the excavation was supported by sticks and crush pillars at the top of the panel. Rock scraped from the panel was loaded by Lad Haul Dumps (LHDs), trammed to an inclined haulage, and loaded into trucks for transport to the surface. It was intended that the Solo would drill from the bottom advance strike drive to the top advance strike drive. Blasted rock would still have to be scraped from the panel. It is also difficult to understand how well the support would have survived. In the initial motivation it was stated that drilling accuracy was of the utmost importance. Previous work by Sandvik Tamrock had shown that, in other parts of the world, 20 metre long holes could be drilled with a deviation not exceeding 100 mm provided that: ? holes were collared with low thrust pressure ? operating percussion pressure was kept low -often not ? exceeding 10 MPa ? drilling was to be with tubes, not rods. In early 1998 initial trials with the Solo H 606 RA were inconclusive; attempts were made to drill 40 metre long holes from one advance strike drive to another. Difficulty was experienced in measuring hole straightness and accuracy, there was no survey of the holes, and no blasting was done to expose hole barrels. A long hole mining system was then defined, with a corresponding face mining system, which led to the design of a test programme for the Solo drilling rig. Earlier experience at Telfer The proposed face mining system was based on a mining method that is practised at Telfer Gold Mine in Western Australia. Telfer has a series of domed reefs that dip at angles of less than 20° to more than 40°. The ore bodies are all thin, with widths from 0.6 metres to 0.8 metres. Figure 1 shows the face layout. Experience at Telfer indicated the following: ? The spacing and size of the dip pillars should be based on the rock mechanics of Union Section ? The length of the face is determined by the ability to correctly position the blast holes. Positioning of blast holes is a function of hole straightness and hole direction. Blast holes in Telfer were drilled 64 mm diameter with retrac bits from Sandvik. Extension steel was T38 by 1.8 metre lengths. A guide rod was fitted immediately behind the bit. To achieve greater accuracy' operators drill at relatively low percussion and thrust pressures. Results show that very good accuracy is achieved in 20 metre stopes and only fair accuracy in longer stopes. In 34 metre long stopes 10-15% of the holes are not sufficiently accurately positioned and have to be re-drilled. All blast holes are

Jan 1, 2006