Search Documents

By D. A. Bruce

The Deep Mixing Method is a very valuable tool for combating problems related to in situ soil treatment, improvement, and retention. Many different variations are used throughout the world, and there is a correspondingly rich technical literature on the testing and properties of the treated soil. This paper provides a synopsis of these aspects.

Jan 1, 2001

By M. A. Schellhardt, E. J. Dewees, R. Vincent Smith

"INTRODUCTION Abnormal material requirements of the nation at war impose an intensive demand upon many irreplaceable natural resources. Natural-3as reserves) for example, are being subjected at the present time to extensive depletion by large-scale withdrawals of gas to supply unprecedented demands for fuel and raw materials for the synthesis of strategic products. Fluids produced from many so-called gas-condensate type reservoirs have become an important source of hydrocarbons vital to the war effort.Development of gas-condensate type reservoirs in Arkansas, Louisiana, and Texas in recent years created many problems not common to ordinary gas-producing operations. Early in the development of condensate-type gas fields, general practices were evolved and applied to insure efficient re¬covery of the hydrocarbons existing in the gas phase under initial reservoir pressures and temperatures, put often the practices were predicted mainlyregardingupon generalized theory regarding the behavior of the fluids and were not always the most efficient, because field and laboratory procedure for testing these hydrocarbons had not progressed as rapidly or as far as field development. Specific information regarding the composition and properties of fluids ultimately recoverable from many gas-condensate reservoirs, especially, is lacking."

Oct 1, 1944

By W. de Beer

We present aspects of one of several ongoing case studies used in the development of prediction techniques for major seismic instabilities. The current investigation centres on accelerated coseismic deformation described by the kinematics of failure and on softening, as well as the characterization of areas of interest by measures of the seismic response at such sites.

Jan 1, 1998

By N. V. Hansell

l. INTRODUCTION. THE last few years have shown an increasing interest in the subject of beneficiating iron-ores -in all iron-producing countries. In the United States, this movement has been slower than in certain parts of Europe, for the obvious reason that the abundance and relative cheapness of the Lake Superior iron ores has hindered the development of enterprises for the preparation of low-grade ores. Gradually, however, conditions have changed. The world's consumption of iron is increasing enormously. Being in 1900 about 40,000,000 tons, in 1910 ii was already 60,000000; and there is no reason to doubt that for the near future the increase in iron-consumption will continue at the same rapid rate, especially with, the development of China, certain parts of Africa, and other regions which have hardly been touched as yet by modern industrialism. It is. therefore, not surprising that apprehension is felt that the known available iron-ore resources of the world are gradually being depleted. Signs of this feeling are the recent investigation, under the direction of the U. S. Geological Survey, of the iron-ore resources of the United States, and the estimate presented to the last International Geological Congress, at Stockholm, Sweden, of the iron-ore resources of the world. These investigations have emphasized the fact that the known high-grade ore-deposits are limited in extent, and will, at a not distant future, be exhausted, compelling the iron industry to depend for raw material on the enormous deposits of low-grade ores which are distributed over almost all the world. The discovery of new deposits of high-grade ore, in countries not yet thoroughly explored, will not materially change this prospect. Of course, the part which such new deposits will play in the future cannot be forecast. The difficulty and cost of transportation will probably exclude many of them from use at the present centers of the iron industry.

May 1, 1912

The case study has identified and characterised additional subsidence arising from longwall mining above or under existing longwall goaf. It suggests that the magnitude, mechanisms and prediction methods for such additional subsidence are different between the two mining configurations. This paper presents a proposed method to predict maximum vertical subsidence due to longwall mining under existing longwall goaf. It suggests that, unless different results from further new cases become available, the findings presented in this article, including the aforementioned prediction method, be applicable to the majority of sites in New South Wales, where multi-seam longwall mining is to take place. This article also presents an important concept of 'overburden modification' due to multi-seam mining. A causal relationship between the above-mentioned additional subsidence and 'overburden modification' has been identified as a result of the case studies. Further investigations into the physical processes that cause such overburden modification will be fundamental to the understanding and management of multi-seam subsidence.

Nov 25, 2010

By T. A. Rickard

The writing that is effective is woven with a fine texture into an agreeable pattern; it is free from knots, loose threads, and stray fluff. The instrument that weaves this literary fabric, whether it produce a homely sock or a lordly tapestry, a simple story or a learned 'Itreatise, is a disciplined intelligence, as sure as a steel needle, as precise as a swift loom. The simile breaks down at this point, for the product of the pen is instinct with the human spirit and therefore transcends in beauty anything made by a mere machine. If words are to be woven into eloquent meaning, they must be well knit. Upon the relation of words to each other and of groups of words to other groups, known as phrases, clauses, and sentences, depends the success of writing as a means of trans¬mitting thought from man' to man. To be understood beyond question, you should know not only what your words denote but how to build your sentences; you must not only choose your words aright but construct your sentences properly. A sentence is a combination of words that makes complete sense; it says something about something. ' A clause is a subordinate sentence or a sentence within a sentence. A phrase is a group of words without a predicate; it makes sense, but not complete sense. For example: I shall wait for a few minutes before I go home: The whole statement is a sentence; "I shall wait" and "before I go home" are clauses; "for a few minutes" is an adverbial phrase. The orderly arranging of words and of combinations of words is called `syntax'; and from the original Greek form, ouvaeis (suntaxis), is derived the Greek name for an editor,

Jan 1, 1931

By David Schlain

"IntroductionThe purpose of this investigation was to study the characteristics of the high-acid electrolytic manganese cell with the idea of fitting it into one of the flow sheets being worked out by the Metallurgical Division of the Bureau of Mines for the recovery of manganese from low-grade domestic ores.In construction, the high-acid cell 3/ differs from the low-acid type in that the cathode and anode compartments are separated by a diaphragm of relatively low porosity, such as alundum. This is necessary because in the high-acid cell the two electrolytes are circulated separately. The anolyte is 15 to 30 percent H2SO4. The catholyte consists of a solution of ammonium sulfate and manganese sulfate with a OH of 4 to 3. The only mixing of electrolytes is that resulting from flow through the diaphragms. In the low-acid cell the two electrolytes are not circulated separately and do not differ so widely in hydrogen-ion concentration. Hence, the canvas diaphragm is sufficient.During operation of the cell, manganese is deposited on the cathode, and sulfuric acid is produced in the anode compartments. Various other reactions take place in the cell. There is considerable decomposition of water; hydrogen is evolved at the cathode, and oxygen is liberated at the anode. When lead anodes are used, some hydrated oxides of manganese are formed at the anodes. The quantity of oxides formed is not as great as it is in the low-acid cell, because fewer Mn++ reach the vicinity of the anodes."

Jul 1, 1942

By G. K. Derby

The Bureau of Mines investigated methods for removing dragline bucket wire rope terminations with the objective of finding efficient methods that are safer than the method most commonly used at U.S. surface mines, which is to use the explosive impact of a projectile fired from a cannon to remove the rope termination. Removal of a wire rope termination for repair or replacement requires separation of the wedge and socket that lock together to secure the rope end. The Bureau investigated currently used methods and improved upon and tested two safer alternate methods for removing wire rope terminations. A cannon test program was conducted, using 40-and 50-gr primer (detonating) cord, to establish the possible force produced with a 4-in-bore cannon and a 55-lb projectile. Wedge and socket units supplied from cooperating mines were separated under controlled conditions to establish data on separation force requirements. The two alternate methods investigated were use of the force generated by (1) a pendulum ram and by (2) a portable hydraulic pusher. Both methods are capable of providing sufficient force to effect wedge and socket separations on draglines with up to 78-yd3 buckets under normal conditions.

Jan 1, 1984

By Harry E. Hughes

A section of the largest Superfund site in the country has become a success story for engineering innovation and for cooperative problem solving. “Superfund site” and “success story” are phrases that are not commonly found in the same sentence. Yet, their use seems justified. The project’s certification of construction completion from the US Environmental Protection Agency (EPA) includes a commendation. It reads, “for completing the project nearly a year ahead of schedule, at a cost substantially less than estimated originally and without com-promising the requirements for protection of human health and safety or the environment.” The EPA director who issued that certification also referred to the project as “a positive example of cooperation among all who have a stake in the outcome.”

Jan 1, 1996

By L. K. Witika, J. H. Masinja

"Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. Of the six frothers tested, two came from the alcohol family, two from the glycol family and last two were formulated products. The initial work involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. For froth stability tests, six frothers were tested on a two-phase (water–air) system using the Bikerman column flotation cell, while water recovery tests were conducted using a total of seven frothers, including the standards for each plant. The results of the testwork showed that (i) although a stable froth is essential for optimum recovery of valuable minerals, a higher molecular weight frother, like Dowfroth 250, caused poor selectivity when used on fine ores and (ii) a lower molecular weight frother was suited for Lumwana ore, while a mid to higher molecular weight formulated product was suitable for Kansanshi sulphide ore. INTRODUCTION Investigations of flotation characteristics of Lumwana and Kansanshi ores using formulated frothers were carried out. The initial work of this project involved determining the optimum mesh of grind and frother dosage for Lumwana and Kansanshi ores. Further work involved carrying out surface tension, bubble size and froth stability measurements. Finally, water recovery tests were conducted at Lumwana and Kansanshi mine sites. In order to investigate the gangue entrainment levels in the Lumwana and Kansanshi sulphide ores, two well-known methods (froth stability and water recovery) were used. Firstly, froth stability tests were conducted using six frothers, two from the glycol family (Dowfroth 200 and Dowfroth 250), two from alcohol family (MIBC and pine oil) and other two from the formulated family (Betafroth 20 and Betafroth 245), at the University of Cape Town’s Centre for Mineral Research (CMR) laboratories. Froth formation and stability measurements were conducted using the Bikerman column flotation cell."

Jan 1, 2015

By D Fergusson, J D. St George

Highwall stability is a major consideration in optimising opencast mine geometry. It involves assessing the risk of those slope failures that are large enough to have significant cost, safety and/or operational implications. These risks are then balanced against the value of the resource to arrive at an acceptable slope design. Load-deformation models (commonly referred to as ænumericalÆ models) of slopes provide a powerful tool in this decision-making process since they can be verified well before slope failure occurs. This gives the slope designer increased confidence in reviewing designs during excavation, potentially allowing early revision of pit geometry to either increase or decrease safety margins as appropriate. However, these models are not always adopted as they depend heavily on an appropriate choice of constitutive model and material parameters.   A preliminary load-deformation model of a 170m highwall in Solid Energy North (SEN) OperationsÆ Awaroa 4 opencast coal mine in the Rotowaro Coalfield has been prepared. This uses a strain-dependent constitutive model based on laboratory test results, strength parameters developed by SEN and excavation monitoring data. The laboratory testing has included triaxial compression tests on large-diameter fractured samples to characterise the stress-strain response of the closely-jointed soft rock masses that exist in many parts of the mine. Data from the monitoring of a 25m cut made during excavation of a haul road has been used to refine and verify the constitutive model. The resulting highwall model has predicted highwall crest movements corresponding to the excavation of each bench, for comparison with monitored values. Key model outputs are total horizontal movements of about 0.5m near the highwall crest and shear strains of 0.5-0.7% at the locations of potential bedding-parallel shear planes underlying the highwall. Most of the movement is expected to occur as creep rather than as an immediate response to excavation.

Jan 1, 2006

How often does one hear that a recent feasibility study was not a success? Alternatively, when scope of the feasibility study was sent out to tender there was a large discrepancy in tendered prices. If the tendered prices were to be compared to the consumer market, for instance the purchase of a car, where the concept is transport in a controlled and safe manner, prices vary by large factors, but then so do the specifications. In the case of a feasibility study, prices should be within a tighter margin as the tenderers are all quoting against the same concept and specification. Why do these discrepancies occur? Price discrepancies will in every likelihood be attributed to two main factors; one, the perceived amount of work and two, the ability of the bidder to carry the risk associated with the feasibility study. It is, therefore, important that the scoping of the feasibility study covers the detailed requirements as clearly as possible stating what level of accuracy is required. The feasibility study is one of the first activities in the life of a project. The study, like the project it is investigating, is subject to the constraints of time, cost and quality. Its primary objectives are to demonstrate the viability of a project within the outlined scope and constraints.

Jan 1, 1998

By Raymundo Del Carpio

El presente trabajo señala las bases que fundamentan la aplicabilidad del extracto de quebracho como depresor en el proceso de flotación, donde se realiza una combinación de un dispersante (producto obtenido a partir de extractos vegetales). También se muestra los avances sobre procesamiento de minerales con alto contenido de pirrotita. En ese sentido, se busca desarrollar una tecnología eficiente y ambientalmente limpia, considerada como una herramienta para la mejora de la competitividad de la empresa, a partir de una visión de desarrollo sostenible.

Sep 9, 2007

Experimental results are presented for the anode overvoltage as a function of current density for different alumina concentrations in an alumina reduction cell. Voltage changes due to the electrolyte resistance and also the decomposition voltage, have been evaluated as a function of alumina concentration and anode current density. From these values of voltage, changes in the total cell voltage have been derived for changes in alumina concentration for different anode current densities. The results show that for each operating current density there exists a discrete alumina concentration that defines a minimum reduction cell voltage. Discussion is made about potential savings in power consumption when the alumina concentration is controlled.INTRODUCTIONThe standard procedure in the aluminium industry when analysing the cell-voltage required for the Hall-Heroult process for reduction of alumina, is to subdivide the total voltage into the following components (e.g. Pearson, 1955; Maritell, 1960).1. ohmic drop through busbars and joints2. ohmic drop through cathode lining3. ohmic drop through anode4. ohmic drop through electrolyte5. overvoltage at anode6. electrolytic decomposition voltage.(Overvoltages ,at the cathode are of negligible magnitude at all practical current densities.)It is understandable that the voltages assigned for each factor invariably differ for different workers...

Jan 1, 1965

By R. L. Kloberdanz

Peruvian legislation requires the preparation of an Environmental Impact Study (EIS) for new and expanding mines/beneficiation facilities and the preparation and implementation of an Environmental Adjustment and Management Program (PAMA) to control and mitigate environmental impacts associated with existing mining/beneficiation activities. Shepherd Miller, Inc., developed guidance documents for preparing an EIS and PAMA for Peru's Ministry of Energy and Mines and presented workshops to Peru's mining industry on preparing an EIS and PAMA. This paper discusses the process and approach taken and the results.

Jan 1, 1998

Peñasquito is Mexico's largest gold producer, consisting of two open pits - Peñasco and Chile Colorado - containing gold, silver, lead and zinc. Over the next three years, mining activities in the pit are expected to be focused on lower grade ore in the upper parts of the Peñasco pit while stripping is emphasized to ensure an economically optimal pit shell design to maximize the net asset value of the operation. By 2019, Peñasquito’s gold production is expected to benefit from an improvement in mined grades as it recommences mining higher grades at the bottom of the Peñasco pit and significantly enhanced metallurgical recoveries with the planned completion of the Pyrite Leach Project ("PLP").

Jan 1, 2017

By Jeffrey Shawn Peterson

The testing procedures of the U.S. Mine Safety and Health Administration specify that intrinsic safety acceptance tests be conducted using a standard tungsten-cadmium electrode configuration in the break- flash apparatus. However, in realistic mining environments, other materials may be more likely sources of sparking. Information defining the probability of spark ignition between common materials such as aluminum, brass, copper, lead, tin, cold-rolled steel, and stainless steel is of more practical value in determining ignition hazards. The U.S. Bureau of Mines has completed an investigation of the influence of material on the ignition probability using the breakflash apparatus. By comparing ignition currents or ignition voltages corresponding to a probability of one ignition per thousand sparks to those found previously for cadmium, a margin of safety may be estimated for each material. This report presents the results of an investigation into the influence of disk electrode material on the probability of ignition.

Jan 1, 2002

By C. E. M. Meskers

Electronic and Electric Equipment contains a range of components made of a wide variation of metals, plastics and other substances. Up to 60 elements can be found in complex electronic equipment: base metals, precious metals and special metals in circuit boards and batteries. Because of its amount WEEE represents a considerable metal resource with a higher special and precious metal content than found in ores. The Umicore integrated smelter and refinery recovers and supplies back to the market 17 different metals from EEE. Pre-treated materials enter state of the art, material and energy efficient metallurgical processes for environmentally sound recovery of metals and treatment of off gasses and hazardous substances. The organics in the feed function as reducing agent and alternative energy source during smelting for precious metal recovery. Lithium-ion batteries are treated using a dedicated process. As a result the environmental footprint of metals produced from EEE is much smaller than primary production.

Jan 1, 2009

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By Mario Terceros H, Bengt H. Fellenius

"ABSTRACTThe city of Santa Cruz, Bolivia, is historically dominated by houses and three to five storey buildings.The geology in and around the city is such that even very light buildings need to be supported onpiles. The recent increase of the Bolivian economy, notably that of Santa Cruz, has created a demandfor new residential as well as office and industrial buildings, which mostly consist of multi-storey orhigh-rise buildings with significantly larger foundation loads. Foundation piles have become largerand longer, and the load on individual piles is increased. The development has resulted in an increasein the demand for more sophisticated design and construction methods and stricter approach toverifying the quality of the construction processes and results.This paper describes to geology of the Santa Cruz region and how the geotechnical conditions areconsidered in the design and construction of piled foundations. The improvement of past constructionand design techniques, based mostly on bored piles constructed with bentonite slurry, is beingreplaced with new methods of constructing bored piles, e.g. the Full Displacement Pile (FDP) andincorporation of techniques such as enlarging the pile toe, e.g., with the Expander Body. This paperpresents the results of several full-scale tests and discusses the incorporation of the test results indesign and construction.1 GEOLOGY OF THE REGIONSanta Cruz de la Sierra is located in the eastern lowlands and sub-Andean zone of Bolivia, SouthAmerica. The area lies at an elevation of about +400 m and the geology is a Paleozoic (250 millionyears old) sedimentary basin. The soils of interest to civil engineering construction are quaternarywith the dominant minerals being calcite, silica and feldspar. The main agent is the Piray River and itstributaries. Their past meandering over the area has resulted in a sedimentation-erosionsedimentationprocess and a profile dominated by fine to medium sands with intermittent layers ofclay or clayey sand. With increasing distance from the river, the clay-containing layers are thicker.Fig.1.- View of Bolivia with location of Santa Cruz and map of Santa CruzThe upper about 15 to 18 m thick part of the profile consists of normally consolidated layers of clays,silts, sands, in various combination and thickness. Below, the soil is more homogeneous and consistsmostly of sand and gravel. The groundwater table lies typically at a depth of about 6 m in the highestpart of the city and at about 1 to 3 m depth in the lowest part of the city."

Jan 1, 2014