Search Documents

The following brief observations on the mineral composition of the Mt. Oxide copper ore are intended to supplement the geological description of that ore-body recently published by Blanchard (2).'" The Mt. Oxide copper mine is situated about 45 miles W.N.W. of Dobbyn, in the Cloncurry district of Queensland (Fig. 1). A representative suite of specimens from the mine was obtained through the kindness of Mr. P. B. Nye, Executive Officer of the Aerial, Geological and Geophysical Survey of Northern Australia, and Mr. Jack Hall, the tributor of the Mt. Oxide mine. The specimens, as shown in Fig. 2, were nearly all from the sulphide zone, between the l04-ft. level and the 300-ft. level. Several additional specimens, together with information which will be referred to later were kindly sent to me by Mr. Roland Blanchard.MINERAL COMPOSITION OF THE COPPER OREThe mineral composition of the ore is relatively simple. It consists essentially of chalcocite, with varying, but minor figures...

Jan 1, 1940

By Volker Vogt, Wolfgang Sand, Eberhard Gock

"For about 20 years, the use of bacteria to control the flotation process for the production of raw material concentrates has been the subject of worldwide scientific and engineering efforts. The objective is to reduce the consumption of biologically non-degradable toxic reagents. The principle idea is to use the activity of bacteria in natural leaching processes – known since the middle of the last century – for controlling flotation processes.It was discovered that the selective activity of bacteria during the extraction of raw material concentrates by means of flotation could also be achieved with extracellular polymeric substances (EPS), excreted by bacteria. EPS, which is extracted by means of centrifuging bacterial cultures, can help to significantly reduce the use of cyanides, approximately 200,000 t/a are used for ore dressing today.The bacterium used was Acidithiobacillus ferrooxidans. In order to identify the bandwidth of the oxidation activity, 21 bacterial strains of the strain collection of the University of Hamburg were attracted to iron(II) sulfate and pyrite under defined conditions. All strains oxidized iron(II) sulfate ten times faster than pyrite.EPS has so far been derived from four strains. In general, EPS extracts are divided into a hydrophilic and a hydrophobic fraction. The hydrophilic fraction is composed of e.g. fucose, rhamnose and glucose; fatty acids such as dodecanoic acid, hexadecanoic acid, octadecanoic acid and nonadecanoic acid were found in the hydrophobic fraction. Pure mineral phases and mineral mixtures were used for the flotation tests. The outcome was reproducible results with technical flotation machines. The research results known so far are mainly based on investigations with micro flotation devices, which are usually used for the characterization of reagents and which do not allow a direct translation to the technical scale."

Jan 1, 2003

By Lewis PJ, Halfpenny R, Craighead GA

Exploration drilling by Joint Venture partners CRA Exploration Pty Ltd and Elders Mining PNG Pty Ltd has discovered a signif- icant copper and gold deposit at the Wafi River prospect, 60km WSW of Lae in Papua New Guinea. An indicated resource of 18Mt at 2.5g/t Au using a lg/t cutoff has been delineated in Zone A. No estimate has been determined for the separate copper occurr- ence at Rafferty's Zone but the copper will be significant to the project. Metallurgical studies on the gold indicate that the primary ore is refractory to direct cyanidation giving a highly variable and inadequate response. All conventional refractory ore oxidation techniques perform well on both ore and pyrite concentrate and oxidation occurs rapidly. No metallurgical studies on the copper mineralisation have been undertaken. Hypogene covellite and chalcocite copper mineralisation is associated with an intensely quartz-stockworked, and quartz and alunite-altered intrusive. Economically significant gold mineralisation occurs in distal subhorizontal lenses, within a sedimentary host, that plunge toward the intrusive. These lenses are sandwiched between overlying quartz and alunite-altered zones and underlying quartz and smectite zones in a mixed zone of quartz, dickite, kaolinite and illite alteration. The alteration and mineralisation is classified as a high sulphidation, epithermal style resulting from the influx of hot, acid magmatic fluids. Preliminary land ownership, road access, power supply and mine infrastructure studies are in progress. The project is currently at an advanced exploration stage.

Jan 1, 1991

By R. W. Watson, H. D. Peer

"This paper outlines the history of steel linings in the Autogenous Mills, the factors influencing the decision to convert to rubber lining, and the operating and cost experience with the rubber liners to date. INTRODUCTIONSherman Mine is an open pit iron ore mining, concentrating and pelletizing operation located at Temagami, Ontario. The operation employs 392 hourly employees and 81 salaried employees and has an annual capacity of over one million L.T. of high quality iron ore pellets produced from low-grade magnetite ore.The Sherman Mine is a joint venture; 90% owned by Dominion Foundries and Steel Limited (Dofasco) of Hamilton, Ontario, and 10% owned by the Tetapaga Mining Company, a wholly-owned subsidiary of the Cleveland Cliffs Iron Company of Cleveland, Ohio. The operation and management of the mine is by Cliffs of Canada, Limited. Development of the property was started in 1965, with pellet plant production beginning on March 17, 1968. At the present time, the orebodies contain sufficient reserves to sustain operations at current production levels for 30 years. Mining was originally carried out in three orebodies, the North, South, and West pits. The North Pit has been exhausted and mining operations ceased in the spring of 1980. A fourth pit, the East Pit, will be developed during the early 1980's."

Jan 1, 1981

By N. S. Kim

Economically favored Cr and Cu leaching out process from spent power plant fly ash (PPFA) had been investigated. PPFA, bearing of C, S, V, Ni, Cu and Cr, has been widely used as an assistant fuel in cement industry. Recent environmental regulation in S. Korea prohibits using PPFA as a fuel. Many researchers have also studied on extraction V and Ni from PPFA. Due to low concentration of V and Ni, 2% and 1%, respectively, economical and environmental friendly process could not be found. In this study, Cu and Cr have been removed in an economical way and which satisfied with KS Extraction Test. The rest unburned carbon, V2O5 and NiO2 in residue were found to be applicable for indoor and outdoor colored bricks or deodorant panel. Various parameters such as pH, lixiviates and time on leaching behavior were investigated in order to leach Cr and Cu remaining C, V and Ni. Keywords: Fly ash; Selective extraction; Ammonia; Deodorant panel

Jan 1, 2009

By R. E. Robinson

I shall present a concept for the development of the resources of this country and its neighbours that repre¬sents a fantastic challenge to our scientists and entre¬preneurs. This concept offers prospects of development that must make our previous achievements seem equivalent only to the first act in a drama enacted on the stage of Southern Africa. I hope to illustrate how, in Act Two, chemistry will play a dominant role, and chemists and chemical engineers will be among the principal actors.

Jan 1, 1980

By Frank van der Meer, Jorge Portocarrero, Alexandra Gruendken

"The number of High Pressure Grinding Rolls (“HPGRs”, also called Roller Press) installations instead of tertiary crushers is rapidly increasing. The technology has been largely accepted in the minerals industry and benefits, such as superior energy efficiency and a lower overall operating cost compared to alternative technologies, have been demonstrated at a number of operations throughout the world.This paper focuses on coarse hard ore operations and reviews the successful installation of the first Roller Press installed instead of a tertiary crusher at the Los Colorados Plant of CMH (Chile) in 1998. It details the experience obtained over the past ten years of operation from commissioning to the present day. It highlights examples of further developments made in the design to improve machine maintainability and availability as well as wear life of the grinding surfaces.A second focus lies on procedures to derive from small scale testing material properties such as wear life, flake formation and strength and their application to industrial size machines to optimize circuit design, especially when Roller Presses are used in closed circuit with screening.INTRODUCTIONRoller Presses (also known as HPGR, High Pressure Grinding Rolls) are considered today state of the art for the preparation of pellet feed. They are also gaining wide acceptance in coarse ore operations. One of the first successful operations in which a roller press was used to replace a conventional tertiary and quaternary crusher is the Los Colorados plant of CMH in Chile.When the Roller Press at Los Colorados was commissioned in 1988, there were 169 Humboldt Wedag roller presses in operation throughout the world. Of these, 14 were installed in the minerals industry. However, these were installed mainly for grinding pellet feed to increase the Blaine value. Up to that time, only three KHD roller presses had been applied for crushing coarse ore in specialized circuits. Moreover, the installation at Los Colorados was the first Roller Press ever to replace a conventional tertiary and quaternary crusher in a hard ore application."

Jan 1, 2009

By Gabriela Pereira de Miranda

Este estudo teve por objetivo avaliar a soldabilidade a pontos entre os aços 22MnB5 e Dual Phase da classe de 800 MPa de limite de resistência (DP800), ambos com 1,8 mm de espessura. A intenção foi determinar os parâmetros adequados de soldagem para esse tipo de junta soldada, que vem sendo progressivamente utilizada na estrutura de veículos automotores, em virtude do uso crescente de peças fabricadas a partir do aço 22MnB5, submetido ao processo de estampagem a quente (hot stamping). Foram avaliadas as propriedades mecânicas através de ensaios estáticos de cisalhamento e de tração cruzada, em juntas soldadas produzidas a partir da variação do tempo de soldagem e da força aplicada pelos eletrodos. Percebeu-se que as juntas confeccionadas com o tempo de soldagem com múltiplos pulsos (9/2/9/2/9 ciclos) e a força de 5,0 kN obtiveram os melhores resultados em cisalhamento. Em contrapartida, os corpos de prova produzidos com a força de 6,5 kN atingiram os maiores valores em tração cruzada. Independentemente dos parâmetros aplicados, todas as condições avaliadas permitiram alcançar o valor mínimo de carga de ruptura necessária para garantir a qualidade de uma junta soldada a ponto entre os aços avaliados.

Aug 16, 2017

By Kelsall D. F, Trahar W. J

The size by size batch flotation behaviour of copper activated sphalerite from synthetic mixtures with quartz was determined. In terms of recovery of sphalerite, the size fractions could be grouped into coarse, intermediate, and fine ranges. The behaviour of the coarse and fine ranges was significantly poorer than that of the intermediate range in both the extent and rate of flotation.Each size fraction had a fast and a slow floating component.The main effect of changing the copper sulphate addition was to alter the proportion of any size fraction which was fast floating. No correlation could be found, between the amount of copper on the spha:lerite andeither the flotation rate of the mineral or the amount of copper added to the system. It was found that fine particles did not appear to consume greatly disproportionate amounts of copper sulphate during conditioning. A modified conditioning procedure was found to lead to a higher rate of flotation and recovery of coarse sphalerite and to make poss1ble substantial savings of copper sulphate.

Jan 1, 1975

Mine Terex articulated dump trucks are working on a large restoration project of an abandoned open cast coal site in Blacklaw, central Scotland. The project is part of the construction of a 42-turbine wind farm complex. During the scheduled 18-month duration of the project, three 28-t(31-st) Generation 7 TA30 dump trucks and the six 36.5-t (40-st) TA40articulated trucks are estimated to move about 1Mm3 (1.3 million cu yd)of material. The trucks are working12-hour shifts, 5.5days a week.

Jan 1, 2005

This technical note describes a problem with WANG82, a ventilation network analysis programme. The problem was highlighted by Renison Ltd when using the programme on large, complex networks. Under certain circumstances the programme produced incorrect results or failed to converge to a solution.

Jan 1, 1986

By Bruce F. Grant

This report discusses research being done by the Petroleum and Natural Gas Branch und the Applied Physics Branch of the Bureau of Mines to deter-mine the most effective uses of explosives in shooting oil and gas wells, as measured in terms of rates of production from the wells. An experimental investigation of the effects of detonating explosives in shallow holes drilled in rocks, chosen to be similar to those forming oil and gas reservoirs, forms the basis of this study. Records obtained from strain gages placed in the rock around the experimental shots permit determination of the generation and propagation characteristics of the strain wave. Water-injection tests made on the test holes before and after shooting allow the increase in fluid conductivity resulting from the shot to be determined. By rotating these data to the physical properties of the rock, and by conducting shooting experiments over the range of rock types common to oil and gas reservoirs, it is expected that relationships between the fluid conductivity and the properties of the explosive and rock can be developed and used for designing efficient shots for oil and gas wells. Four series of experiment.al tests were completed during the summer of 1949 and are described herein. The results of these tests confirmed the feasibility of the experimental approach and permitted outlining the plans for future research discussed in this report. This report is presented to acquaint industry with this research program and the progress to date, so that the Bureau may have the benefit of suggestions from interested readers.

Jan 1, 1950

By A. J. Miscoe, W. M. McKewan, J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two 2 in-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine. These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope Lo determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 1992

By N. Mphathiwa

When slope angles are designed during open pit optimization, there is a risk factor applied in steepening the slopes. The steepening of slope angles has implications for the safety and economics of the mining operation. The steeper the slope angles, the greater the probability of slope failure. Although a slope failure will result in added costs, the challenge is to compile an accurate cost-benefit exercise optimizing the economic benefits of the project without exposing mine workers and equipment to unacceptable risk of rockfalls. A balance between the safety of the operation and the economics of the investment is therefore required. The ideal situation is to have a slope monitoring system that will predict slope failure by detecting any ground movement before the actual failure occurs. This early warning will allow the risk factor to be applied with a high degree of confidence, knowing that the risk will be adequately mitigated. The objective of this paper is to provide guidelines on how to design an optimal survey slope monitoring system. It is the authors? view that for a survey monitoring system to yield desirable results, it should adhere to survey principles such as working from the whole to part and consistently cross-checking. The case study used is Jwaneng Mine, and the design strategy outlined can be used as a guideline for developing a new slope monitoring system or to optimize an existing one.

Jan 1, 2014

By S. McPherson, M. Chalkley, R. Ellenwood, W. Nicot

"The Moa JV was formed in December 1994 as a 50/50 joint venture between Sherritt Inc. and General Nickel Company S.A. of Cuba. The joint venture consists of the mine and Pedro Sotto Alba processing plant in Moa, Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Throughout its now nearly 23-year history, the Moa Joint Venture has faced a number of global, operational and process challenges. Global challenges have included high input costs such as for fuel oil and sulphur, as well as low nickel prices. Operational and process challenges have included increasing ore haulage distances, decreasing ore Ni + Co grades, and increasing ore impurity contents. For example, increases in impurities such as Mg and SiO2 in the ore result in increasing acid demand in leaching and decreasing solids content of preheated leach feed slurry, respectively. In spite of these challenges, the mixed sulphide production capacity from the Moa Joint Venture has increased from 12,500 to 37,000 t/y Ni + Co since 1994 by judiciously targeting expansion projects and by continuously performing process and operational improvements.INTRODUCTION The Pedro Sotto Alba high pressure acid leach (HPAL) plant at Moa Bay, Cuba has a long history (Maslenitzkiy, 1969; Chalkley, 1996; Carlson, 1960; Roy, 1961; Carlson 1961). The plant was constructed by Moa Bay Mining Company and started up in late 1959 after several years of process development by Freeport Nickel Company, including operation of a 10 t/d plant in Hoskins Mound, Texas and a 50 t/d plant in Port Nickel, Louisiana (Southwick, 2004), as well as development work by Chemical Construction Company (Chemico) to precipitate metal sulphides (Roy, 1955a; Roy, 1955b). The Moa plant had an original reserve of 50,000,000 t of ore, graded at 1.35 wt% Ni, 0.146 wt% Co, 3.70 wt% Si, 1.00 wt% Mg and 4.5 wt% Al. At original design rates of 2,000 kt/y of ore, the design capacity of the plant was around 25,000 t/y Ni + Co as a mixed sulphide product, which would be shipped to the Port Nickel Refinery in Louisiana for processing. In 1960, the plant changed ownership and was restarted in 1961 under Cuban management. Between 1961 and 1989, the plant was also supported by involvement from the former USSR, supplying spare parts and consumables. In 1994, Sherritt Inc. partnered with the General Nickel Co. S.A. of Cuba and formed the Moa Joint Venture. This joint venture includes the mine and Pedro Sotto Alba HPAL processing plant in Cuba and the Corefco refinery in Fort Saskatchewan, Alberta, Canada. Under this partnership, ore is processed in Cuba to produce a nominally 55 wt% Ni and 5 wt% Co mixed sulphide product that is shipped to Canada and processed by Corefco to produce class 1 nickel, high grade cobalt and byproduct ammonium sulphate fertilizer."

Jan 1, 2017

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By William D. Hissem

While much technology has been developed and brought to bear in the area of blasting applications, the foundation work required for success in the muck pile begins with the drilling program.

Jan 1, 1997

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By C. D. Elifrits, N. B. Aughenbaugh

Introduction Federal and state laws enacted to regulate coal mining and the accompanying public concern about the adverse effects that mining might have on land use have focused much attention on the subsidence of the land surfaces over underground mines. Some questions asked are: • Will abandoned mines subside in the future even though they have exhibited no surface adjustment to date? • If so, when will subsidence take place? • Can a specific surface area be affected by subsidence more than once? • What surface form will the subsidence feature take? • Is there any way to predict when subsidence will occur and end? An attempt is made here to address these questions insofar as it is possible with available data and experience of evaluation of subcritical extraction conditions. Mining that results in subsidence features can be classified as supercritical, subcritical, and critical with respect to the minimum span lengths of the worked-out rooms (Fig. 1). A complete basin will not develop fully immediately over subcritical conditions because the span lengths of the entries are less than the critical dimension (Wardell, 1983). Passageways, entries, and room-and-pillar panels are all included in the subcritical category. Because of the short span lengths, subcritical mining conditions tend to be stable over the life of the mine unless adverse geologic conditions exist (Gray et al., 1974; Dunrud, 1976). Various roof control and support procedures are employed to maintain entry stability during mining. Little information exists concerning the time factor of subsidence over areas of subcritical extraction. Data that have been collected relate to longwall mines, whereby the cavity sizes are designed large enough to induce caving behind the working faces so that complete subsidence at the surface occurs within a short period of time. The UK's National Coal Board (1975) has reduced the enormous amount of data it has collected to empirical correlations and has published these correlations in its Subsidence Engineers Handbook. The handbook states that "None of the foregoing remarks applies to pillar and stall working," with respect to the section discussing the time factor of subsidence caused by longwall mining (National Coal Board, 1975, p. 40). To understand and evaluate how time relates to subsidence above room-and-pillar mines, one must first recognize how mine cavities deteriorate and fail. The propagation of failure to the surface must then be studied, and, finally, the failures that are manifest at the surface in the form of depressions accompanied by both compressional and tensional movements must be investigated. Failure of mine cavities Any cavity beneath the earth's surface represents a condition of nonequilibrium and tends to close with time. Failure of cavities in a subcritical mine can be classified as failure of the roof, failure of the floor, failure of the supports (pillars, cribs), and elastic rebound of the rock. One mode of failure may dominate, but generally combinations of the four will occur. Also, initial instability of geologic materials and structural features and in situ stress may be unknown factors that can contribute to cavity failure. Roof failure is the most obvious opening stability problem in most operating mines. The bridging capabilities of the roof rock are dependent on the rock's material strength, geologic discontinuities, and reaction to humidity changes in the air of the mine. This type of failure may vary in magnitude from gradual flaking to massive roof falls. Mine floor instability can be manifest in the form of a general heave over a broad area or of individual pillar punching. The weaker and thicker the immediate floor material, the more prone a mine is to experience floor problems. Water seeping into an area can soften the underclay, reduce its bearing capacity, and precipitate failure of support for the overburden.

Jan 8, 1986

Mt Waruwari, host to the Porgera underground gold mine in the Highlands of Papua New Guinea (PNG), is a prominent ridge of sediments and dioritic intrusives rising approximately 600m above the surrounding valley floor. Consequently, mining occurs in a low stress environment where structural and material considerations are foremost in the design of ground support and reinforcement. Three major rock types are encountered in the underground mine. These are locally referred to as "black sediments" (slightly indurated mudstones and clayey siltstones), "altered sediments" (derived from black sediments by thermal metamorphism), and "intrusives" of dioritic composition. The rocks are moderately to highly fractured, the black sediments being generally weak and occasionally sheared while the altered sediments and intrusives are quite strong but often brittle. Mining takes place from a series of stopes extracted by either slot and mass blast or a modified vertical crater retreat method (VCR), which are backfilled with a cemented rock fill. Ground support and reinforcement has been relatively conserv- ative to date and generally relies on pattern reinforcement of all development with cement grouted "rebar" bolts and mesh, extending to pattern cable bolting with occasional mesh in stope backs. In addition there has been considerable reinforcement of stope hangingwalls in some cases. A programme of broad scale structural mapping, monitoring with extensometers, material property testing, and stress analysis has been devised to allow optimum design of ground support and reinforcement in the future. Considerable work remains to ,omplete this task.

Jan 1, 1991