Search Documents

By R. L. Rough

Photoelastic, wire resistance, and borehole-deformation gages were used to measure the in situ strains when an outcropping Black Hand Sandstone Formation in Hocking State Forest, Hocking County, Ohio, was overcored to stress-relieve the surrounding sandstone. Strains transmitted to the photo-elastic gage did not produce isochromatic patterns suitable for quantitative analysis. Strain readings from the wire resistance gage indicated tensile-strain loading during overcoring; readings from the strain-gage bridges in the borehole-deformation gage indicated compressive-strain relaxation during overcoring. The magnitude and orientation of the computed stress fields obtained from both gages were comparable when the corresponding tensile and compressive elastic moduli were applied. Stresses computed from deformation and resistance gages at depths to 5 feet showed the maximum stresses to range from 1.042 to 2.121 times greater than the minimum stresses. The bearings of principal stresses calculated from the deformation gage readings varied between N 61° E and N 83° E; the wire resistance strain gage bearing computations varied between N 68° E and N 82° E. Measurements of in situ strain in sandstone were shown to have promise but to require further development in field technique that could likely be achieved through experience.

Jan 1, 1971

Typically, large volumes of data are collected during geotechnical investigations for mining projects but rarely is this done in a comprehensive manner that enables all aspects of the geotechnical environment to be evaluated. A geotechnical core logging process has been developed to record mechanical and structural properties of the rock mass. The method enables data for a wide range of rock properties and geotechnically significant major structures to be collected including rock strength, joint surface condition, fracture frequency and fracture orientation. The logging method is unique in that sufficient data is collected to enable the independent determination of all the major rock mass classification systems including rock mass rating (RMR), (Bieniawski 1976, 1989; Laubscher, 1990) Norwegian Geotechnical Institute (NGI) tunnelling quality index (Q) (Barton, Lien and Lunde, 1974) and geological strength index (GSI) (Hoek, Kaiser and Bawden, 1995). The logging system has been specifically developed to allow better and more precise appreciation of rock mass and structural conditions across the project area thereby optimising the use and application of the available geotechnical data and improving confidence in the outcomes of geotechnical investigations. This paper describes the core logging process with case examples showing how the logged data can be used for underground and open pit mine design.

Nov 25, 2010

Stope back conditions in the cut-and-fill stopes at New Broken Hill Consolidated Limited often deteriorate to such an extent that, because conventional rockbolts are not able to maintain safe working conditions, square-set timber is installed. An attempt to eliminate this costly procedure has involved the use of long grouted rockbolts using high tensile prestressing wire. These bolts were developed in conjunction with the prestressing engineers of BBR (Aust.). This form of support has improved the back conditions, maintained safe working conditions, and delayed the introduction of timber in a number of stopes.Production from these stopes has been maintained at its previous level (at a rate approximately double that of a comparable timber stope).

Jan 1, 1974

By Armin W. Stuedlein, Youssef Bougataya

Early stage design of driven piles primarily relies on static analysis based on one or a combination of total and effective stress approaches, the latter known as the method to estimate axial capacity. A database of 85 piles driven in the Puget Sound Lowland region and monitored at End of Driving (EOD) and Beginning of Restrike (BOR) was compiled along with capacities estimated using the CAPWAP procedure. Established soil profiles based on borings with standard penetration tests (SPT), cone penetration tests, and geologic maps were matched with their corresponding unit shaft resistance profiles from the CAPWAP procedure and resulted in more than 1,200 observations. In this study, eight new models were developed to predict the coefficients at EOD and BOR, based on the corresponding USCS categorization. Each coefficient model is formulated using a three-parameter exponential function, calibrated to capture the profile of coefficients with depth. These models could benefit the designer by providing them with a simple, empirical model that accounts for soil type and setup in a smooth, continuous function with depth. A parallel analysis was performed to assess the accuracy and variability of the formulated prediction models to facilitate implementation in load and resistance factor design (LRFD). INTRODUCTION The design of the axial capacity of driven piles during the planning stages of a project is typically based on a static analysis approach. The goals of this approach are to predict the components of capacity, consisting of the shaft and toe bearing resistances, and to assess project concept feasibility and preliminary lengths. In most cases, this analysis is based on empirically-developed methods, such as the total stress method, also known as the method (Tomlinson 1987) or the effective stress method known as the method (Esrig and Kirby 1979; Fellenius 1991). Many other methods, such as those based on in-situ test results exist and rely on correlations of blow counts from the standard penetration test (SPT), and cone tip and sleeve friction resistance from the cone penetration test (CPT), to shaft and toe pile resistances (Schmertmann 1978; Meyerhof 1976; Nottingham and Schmertmann 1975; Nordlund 1963; Eslami and Fellenius, 1997; De Ruiter and Beringen 1979). Although these methods were generally developed using data from specific geological regions, they are often recommended in national design manuals (e.g., FHWA, Hannigan et al. 2006).

Jan 1, 2018

By Stênio Cavalier Cabral

O diboreto de titânio (TiB2) é um material cerâmico de alta dureza com uma grande potencialidade de aplicação tecnológica. No entanto, existe uma grande dificuldade de se produzir corpos bem sinterizados desse material, quando são usadas técnicas convencionais de sinterização. Neste trabalho, foi empregada uma técnica de processamento em altas pressões e altas temperaturas para produzir compactos de TiB2 com AlN. Amostras cilíndricas, com 5 mm de diâmetro e 7 mm de altura, foram processadas durante diferentes intervalos de tempo compreendendo os ciclos de sinterização. O principal objetivo do trabalho foi à realização do ensaio de torneamento para a avaliação de desempenho dos compósitos produzidos e sua relação com a quantidade de ciclos de sinterizaçãos em condições reais de trabalho. Os resultados obtidos apresentam perspectivas interessantes de utilização do processamento em alta pressão e alta temperatura para produção de inseros para aplicação na usinagem do ferro fundido nodular.

Aug 16, 2017

By Madgwick J. C

A new strain of Thiobacil/us ferrooxidans (SPK I) has been isolated which has a higher copper to iron release ratio (2.04) than the standard T ferrooxidans (CPBI) (1.12). The diminished iron oxidizing ability enables almost quantitative release of copper (93 per cent) from a chalcopyrite-rich concentrate without interference by iron reprecipitation. In a single batch leach, Bougainville copper concentrate yielded 9.3 grams/litre soluble copper from a 4 per cent w/v suspension in 100 days at 32°C.Solvent extraction recovery of soluble copper is recommended as a final step in a leaching process.

Jan 1, 1983

By H. William Zeller, T. E. Westpha1

The U.S. Bureau of Mimes evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pct, depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O, but it increased CO, and NO,. The increase in NO,, of about 12 pct, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 1992

The early records of hydraulic elevator and bucket ladder dredging in the Clutha River system indicate the success of that era of alluvial gold mining in Otago. This paper briefly reviews parameters of depth and gold grade for alluvial operations. The application of dragline technology is proposed for the economic removal of overburden to target the deeper alluvial gold areas which remain in the Otago region.

Jan 1, 1992

By Thomas V. Falkie

In bygone days, the mineral engineer spent most of his/her time on the technical aspects of designing, building, and managing mineral operations. In the last few decades, mostly since the 1960s, increasing amounts of engineering man power and time are spent dealing with federal, state, and local government agencies, laws, and regulations. It is not possible to plan, design, build, or operate mines, mills, smelters, or even office buildings without detailed consideration of government regulations and permitting requirements dealing with environment, worker health and safety, etc. The four chapters of this section provide an overview of the social, legal, political, environmental, and health and safety aspects of mineral enterprise. The section sets the stage for the working engineer/geologist in industry, government, consulting, or academe and points the direction for more detailed study in each of these areas.

Jan 1, 2008

By Leonardo Zuchi Guio

A ArcelorMittal Tubarão vem trabalhando nos últimos dois anos na implantação de um sistema automatizado de julgamento da qualidade da superfície de bobinas laminadas a quente, juntamente com a ArcelorMittal Global R&D. Tal sistema é denominado CGSIS – Coil Grading Surface Inspection System – e tem a função de interpretar as ocorrências de defeitos superficiais, identificados por um sistema de inspeção automático através de câmeras CCD auxiliado por técnicas de visão artificial, à luz da necessidade requerida pela aplicação final do material. Todas as ações sugeridas pelo sistema são baseadas em regras de aplicação e nas informações obtidas do sistema de inspeção automático, requerendo para isso taxas de acerto de classificação de defeitos adequadas para uma boa tomada de decisão. Para tanto, várias melhorias foram necessárias, envolvendo questões de ambiente, desempenho, confiabilidade, disponibilidade e treinamento do sistema, para se obter com isso melhores níveis de detecção e acerto. Outras questões envolvidas em tal processo concernem às mudanças aplicadas a políticas já estabelecidas de julgamento e comunicação do novo sistema com os sistemas já existentes. Vários benefícios da implantação do projeto já estão sendo percebidos provenientes das etapas de preparação para a instalação e espera-se que após a operacionalização um ganho superior a R$320k entre redução de custo com pessoal, aproveitamento de material e redução de reclamações de clientes seja alcançado.

Jul 30, 2018

A concise country-by-country summary of the mineral industry of Africa is presented. Reserves, resources, role of the country in the world mineral supply, and developments in the mineral industries are reviewed. The data on each country are accompanied by a map showing mineral location and transportation facilities.

Jan 1, 1976

By J. H. Starkey

SAGDesignTM Testing for grinding mill design was introduced commercially in 2004. Up to January 2008, 18 projects have been completed and 99 samples have been tested using this method. Two papers have been published describing the patented test procedure and one of these shows how the results compare with other grinding test methods. This paper will briefly discuss the theory on which this technology is based, and explain the procedures used to develop the calibration equation. Case studies are also included to demonstrate the effectiveness of the test work being done. These case studies show how the SAGDesign test is being used today: to design new grinding circuits for commercial full scale use; to calculate throughput in existing mills for production planning; and to accurately define grinding mill requirements at the scoping, pre-feasibility or feasibility study stage of project development, in order to economically identify the size and cost of the grinding mills that will be needed for the project. This is important because if the full rec-ommended SAGDesign testing program is done at an early stage in the project, the definitive cost for a guaranteed throughput, grinding mill design (by Outotec if their mills are purchased) is available. New grinding mill design for final engineering will be represented by the test work done on the Climax Molybdenum Project for Phelps Dodge (now FMI) in Colorado, USA. The SAG mill and ball mill for Climax are now in fabrication with project start up in late 2009. Next, the sizing of grinding mills at the scoping, pre-feasibility or feasibility study stage of mine development will be represented by a large metal mining property in Russia. Finally, calculation of the throughput for existing mills will be represented by work done at a base metal mine, in eastern Canada. Test work for designing SAG mills is now done in four laboratories at the time this paper was written. One in the USA at Dawson Metallurgical Laboratories, Inc. in Salt Lake City, two in Russia at the TOMS Research and Design Institute and at the Irgiredmet Research Institute, both in Irkutsk, and a fourth mill has been installed in Australia at AMMTEC Limited?s lab in Perth. A fifth SAGDesign test mill for radioactive ores has been built by Starkey & Associates, specifically for testing uranium ores and can be moved to any licensed lab in the world on a project basis.

Jan 1, 2014

By Ching-Liu Wu, John Hawley, Andrew H. Liu, James Chai

The Hatch Mott MacDonald/Bechtel Joint Venture team is designer and construction manager for the 5.25-mile Tunnel Segment of the overall 16-mile Silicon ValleyRapid Transit Project, which extends the existing Bay Area Rapid Transit (BART) system southward from Fremont to San Jose. The Tunnel Segment includes twin boredtunnels, mined cross passages, and three deep station excavations situated in highlyvariable ground, high ground water table, and a dense urban setting with high-risebuildings adjacent to the largest excavation. This paper will discuss design challengesthat have arisen with the excavations and the proposed solutions.

Jan 1, 2007

By Anu Martikainen

Utilization of belt air in underground coal mines has been discussed extensively during the last decade. The Final Report of the Technical Study Panel on the Utilization of Belt Air and the Composition and Fire Retardant Properties of Belt Materials in Underground Coal Mining formed by the Miner Act of 2006 recommends research on leakage, use of booster fans, and escapeway safety. This paper discusses the role of ventilation modeling in evaluating primary escapeway pressurization in a three-entry development system to improve emergency escape in a coal mine using belt air. The intake entry of the NIOSH Bruceton Experimental Mine was pressurized using a 1.1 m (42 in) diameter, 37 kW (50 hp) fan. The work details air movement in the simulated three-entry system and the resulting leakage patterns. Three mine ventilation software packages were compared to analyze their performance in predicting the airflows and leakage conditions with different fan settings. NIOSH researchers found that the measurement results correlated well with the results of modeling.

Jan 1, 2010

By B. J. Clauzier

"The Falconbridge Limited approach to employing communication equipment is first, to determine what is required in a given situation, second, to evaluate the possible alternatives, third, to select the most suitable hardware and, fourth, to determine what modifications, if any, are required to ensure not only successful implementation but continued low-cost reliability. Two examples are examined.The first situation required remote video monitoring of an acid loadout station. Several alternatives for linking to theremote site were investigated, including hard-wired, slow-scan and microwave. A comparison of these alternatives is shown and an appraisal of the performance of the selected microwave link is presented.The second situation required direct voice contact between the two members of an underground tram crew. Alternative solutions are described and an evaluation of the selected system- SHF portable radios - is presented.ObjectivesIn general, projects must have four main objectives: (1) to improve the safety of its operations; (2) to reduce its operating and capital costs; (3) to increase the efficiency of its work force; and (4) to increase its productivity. ScopeCommunication, when used wisely, can be a good tool to achieve these objectives. Projects can be kept simple using existing technology and adapting it to a particular task. To ensure the success of the project, it was necessary: to determine the project objectives; to evaluate the possible alternatives; to select the most suitable hardware; to adapt the hardware to the application, if required; and not to provide more than is necessary.Application at FalconbridgeTo illustrate this approach, two examples of actual installations at the Sudbury Operations are presented, sulphuric acid loadout, and the Falconbridge Mine haulage system."

Jan 1, 1987

By David R. Mitchell, Ernest M. Spokes

There is evidence that study of minerals now considered to have susceptibilities too low for magnetic separation should be continued. Present concepts may be false. INFORMATION on magnetic properties of minerals other than magnetite is scanty and sometimes erroneous. Often there is no information at all. W. R. Crane's table of tractive forces published in 1901 is still the best guide in the field, but Crane's data can be used as a guide only, since he ignored such important factors as impurities in the minerals, size, and packing effect. During the 1930's work by the U. S. Bureau of Mines added greatly to knowledge of the behavior of certain minerals in a magnetic field. The USBM bulletin gave for the first time complete magnetic characteristics for magnetite and fragmentary data for a few other minerals. The work reported here covers a study of the magnetic-susceptibility relationships of the wolframite series of minerals and sphalerites as related to their chemical compositions. Theories are proposed to explain divergences found from commonly accepted beliefs. Gouy Method for Determining Magnetic Susceptibility: The Gouy principle has been adequately described in the literature1-3 and applied in various ways.'- It may be summarized by stating that a body of material (gas, liquid, solid, or powder mixed with gas or liquid) of cylindrical shape changes in apparent weight if suspended with one end in a zone of higher magnetic field strength than is found in that portion of the field surrounding the other end of the cylinder. This may be expressed as K2 - K1 A (H2 - H2) - mg. [1] In determining the susceptibility of mineral specimens by the Gouy method, the mineral is reduced to a fine powder and packed in a glass weighing tube. Precise measurement of the bore and depth of the tube is made unnecessary by a calibration procedure. Using the basic expression of Eq. 1, Hoare"

Jan 1, 1959

The subject which I have chosen for my paper is one that I am sure has occurred to the minds of nearly every mining man on these goldfields at some time or other. I refer to the carrying out of hydraulic mining on a fairly large scale on some ofthe alluvial areas of the West Australian goldfields. There are many, no doubt, who have the question ready at the present moment, "But where is the water coming from? " However, the great difficulties in the way are not due to the want of natural facilities, but due to the fact that sufficiently large areas cannot be leased for this purpose under the present Mining Act. Now, ever since the inception of the West Australian goldfields there has been the old familiar cry when referring to some alluvial gully or flat, "I wish I had a head of water to sluice that ground," but what seems an impossibility at times can be brought to a very great possibility by the use of a little thought and the expenditure of the necessary capital. This is so as regards West Australia with sluicing which, in spite of the its having so many detractors, can be carried out successfully in certain localities if the ordinary facilities on the part of the Govenment are given, and on the other hand the necessary capital is supplied. Alluvial gold areas, I propose now to draw your attention to first of all, the numerous alluvial areas that exist around Coolgardie, Kalgoorlie, Bulong, Kurnalpi and many other centres. Some of these areas have afforded fortunes inthe early days to the alluvial miner, and also afforded a living for years to many diggers' by the use of the dryblowing...

Jan 1, 1901

FREQUENTLY the Survey Department is caIled upon to estimate the quantity of material in various dumps, dams piles, etc... and in the carrying out of this work various methods may be employed.The method used will vary according to the particular case in hand, and factors such as accessibility of the top of the dump, steepness of its sides, height, and the condition of the material to be estimated. A certain amount of "give and take" must be adopted in the treatment of small local cavities and mounds.In all cases it is desirable that the surveys made should be tied on to the lease surveys for the purpose of location, and that all levels should be reduced to the mine datum. It is also desirable to obtain levels of the original surface before deposition of the material to be estimated. If these have not been obtained beforehand, levels and transfers round the top will be the next best. If space is availabIe, flat surface is chosen as a site for the dump, etc. This is of the utmost importance in those cases where the material will have to be...

Jan 1, 1925

By Aldin Ardian, Mustafa Kumral, Jagjit Singh

Risk assessment of mining projects is a requirement in the mineral industries. In this process, many risk variables are timedependent, and the only available data are historical time series. Moreover, in the case of a multivariate scenario, conventional forecasting methods fail to capture conditional dependency across the variables, which is important when there is an underlying causal relationship that needs to be modeled for accurate project evaluation. Thus, we investigated the use of copulas to capture the conditional distribution of the factors involved in a mine risk assessment study. We employed a multivariate copula-based time-series approach to model several uncertain variables. The Autoregressive Fractionally Integrated Moving Average - Generalized Autoregressive Conditional Heteroscedasticity (ARFIMA-GARCH) model was used for the conditional mean and copulas were used to model the error distribution, thus capturing the collective variation and dependence pattern across the variables. The method was implemented to model gold prices, copper prices, and the 10-year US Treasury bond yields and to determine the project’s net present value and probability of being economically feasible. The proposed approach can be used for cases where simulation of multivariate time-series is conducted.

Apr 13, 2021

By H. Powell

"This paper discusses how elemental analysis of conveyed bulk flows in real time using PGNAA (Prompt Gamma Neutron Activation Analysis) technology has resulted in significant improvements in advancing plant control in mineral processing operations. PGNAA through belt, full stream, continuous, multi-elemental, real time analysis technology is explained. Capabilities and limitations in plant operating environments are discussed including comparison with other real time, on-line technologies through review of published information available for on-conveyor minerals applications. Case studies include an iron ore and copper-gold company, both of which consider the technology an essential component in advanced plant control necessary in new process flow sheet designs, rather than an optimisation tool.INTRODUCTION Process operators rely on supply of a reasonable ore quality and consistency from the mine. Unfortunately neither the mining nor process operators have much control over the ore quality once it has been put into the crusher. Grade control typically stops once the material is designated as ore and the process plant operator needs to process it irrespective of quality. Plant control is most effective when technologies measure process streams directly and preferably in real time. Measuring sampling streams that are not representative of the primary flow will result in incorrect plant control decisions. Sampling coarse conveyed flows is expensive and impractical at many operations, however, this does not mean those flows cannot be measured. Investigations to find techniques suitable for real time elemental analysis have focussed on the application of known laboratory techniques to process streams. For conveyed applications, development of neutron irradiation techniques were most promising and early studies indicated potential success for bauxite measurement (Beurton et al, 1995). Tran & Evans (2001) concluded there was no equivalent technology to PGNAA in terms of material penetration power and that the technology was eminently suitable for basic industries such as cement. Nelson and Riddle (2003) evaluated PGNAA for possible use in the phosphate industry by using a unit installed in a cement plant to test performance on phosphate samples and ultimately recommended its use for further characterisation of the mine’s various ore types to improve stockpile allocation and grade control"

Jan 1, 2014