Search Documents

By Agne Rustan

This paper is intended to give a summary of the first ten Symposia on Rock Fragmentation by Blasting where the symposia activities were governed by a Steering Committee replaced at Fragblast 2 by an International Organizing Committee (IOC). At Fragblast 9 the name was changed to Fragblast International Organizing Committee (FIOC). Eighty four pages of statistical data about Fragblast 1-10 is documented on the Fragblast Website (ISEE.org).

Jan 1, 2014

By M. Cai

A practical simple method is proposed to estimate the tensile strength (st) of strong brittle rocks from the strength ratio of R= sc/st = 8 sc/sci, where sc is the uniaxial compressive strength and sci is the crack initiation stress in an uniaxial compression test. 8 is the Griffith strength ratio and the term sc/sci accounts for the difference of crack growth or propagation in tension and compression in uniaxial compression tests. sci can be reliably obtained from volumetric strain measurement or acoustic emission (AE) monitoring. With the strength ratio R determined, the tensile strength can be indirectly obtained from the result of uniaxial compression tests. In addition, a practical estimate of the Hoek-Brown strength parameter mi is presented and it is suggested that mi = 12 sc/sci can be applied to strong, brittle rocks in high confinement zone and mi = 8 sc/sci can be applied to low confinement to tension zones. It is found that the predicted tensile strengths and Hoek-Brown strength parameter mi using this method are in good agreement with test data. The rock strength parameters like st and mi, which require specialty tests such as direct tensile (or Brazilian) and triaxial compression tests for their determination, can be reasonably estimated from uniaxial compression tests.

May 1, 2009

By K. V. K. Prasad

Stochastic simulation has been routinely used for performing risk and sensitivity analyses in a variety of fields. The commonly used means of generating the simulations has been the Monte Carlo approach which usually employs a Simple Random Sampling (SRS) scheme of the variable distributions. This method is prone to sample clustering and requires a large number of samples to represent the distribution faith-fully. This can become problematic for simulating complex processes where it is impossible to run an arbitrarily large number of replicate simulations. The Latin Hypercube Sampling (LHS) method uses a stratified sampling approach which assures representation of the input distributions for any given number of samples. In this paper the LHS and SRS approaches are compared using a petroleum resource estimation example.

Jan 1, 1993

By Kenneth Maas

The Bureau of Mines devoted portions of the 1987-1988 field seasons to investigate the mineral aggregate industry in Juneau, Skagway, Haines, and Gustavus, Alaska, as part of the Juneau Mining District study. Statistics compiled for current suppliers include location, activity, reserve estimates, expected mine life, and types of commodities available. Each population center, except for Gustavus, is well endowed with suitable mineral aggregate to last at least 20 years. The Bureau of Mines quantified the mineral aggregate resource in many large potential sites within each area. Sampling, engineering and soil-index testing, site descriptions, deposit dimensions, and gold recovery information is described. Refraction seismic studies performed at three localities revealed gravel thicknesses in excess of 40 to 80 feet. In the Juneau area the Herbert/Eagle Rivers outwash area, East Fork Lace River. Antler/Gilkey Rivers, and Grizzly Bar (Taku Inlet) individually contain in excess of 60 million yd3 of excellent-quality aggregate with minor accessory gold credits. Haines is also well endowed with aggregate resources; large, quality deposits occur along and at the confluences of the Chilkat, Katzehin, Klehini, Tsirku, and Kicking Horse Rivers. Large deposits of granitic aggregate exist in the Skagway River and East Fork Skagway River.

Jan 1, 2012

By Thiago Augusto Ávila

A limpidez de aços e a diminuição de problemas de lingotabilidade em aciarias tem sido alvo constante de esforços de engenheiros na siderúrgica. O bom entendimento dos efeitos do processo e as suas respectivas particularidades garantem a redução de ocorrências de inclusões e má lingotabilidade. Dentre os principais aços de construção mecânica com maior ocorrência de problemas de inclusões e lingotabildade estão os aços “Baixo Si” e aços com faixa de S e acalmados ao Al e Si/Mn. Entre os parâmetros de análise, a ordem de adição de ligas, definição de temperatura de lingotamento e a estabilidade térmica e química, são os de maior influência na quantidade de inclusões e problemas de lingotabilidade. Para aços baixo Si, a pré-desoxidação com Al, auxiliada por maiores temperaturas de lingotamento, confere inclusões líquidas no inicio do processo promovendo a maior remoção destas. Da mesma forma, aços com S e Al são beneficiados pelo aumento da temperatura de lingotamento, mas fortemente afetados pela estratificação térmica do aço na panela, quando é elevado o teor de S e Al nestes. Sendo assim, o tempo de espera e o estado térmico da panela e distribuidor passam a ser um fator importante para redução da estratificação térmica bem como a redução de problemas com macroinclusão e má lingotabilidade.

Jul 30, 2018

By I. Haskett

ABSTRACT The Redwater pool, in north-central Alberta, was discovered in October, 1948, and at the end of 1950 was about 85 per cent developed. Production is from a Devonian coral limestone reef and is found at an average depth of 3,150 feet. The pool has an estimated .productive area of 37,000 acres, and a maximum oil zone thickness of slightly over 200 feet. Wide variations exist in both type and values of porosity, with the average value determined for the reservoir being 6.16 per cent. The total stock tank oil in place is about 1.24 billion barrels. The crude has a saturation pressure of 485 psig, com-pared to the original value of 1,050 psig for the reservoir, and the principal recovery mechanism so far has been the natural water drive. Cumulative production to January 1st, 1951, has been about 15.5 million barrels. These withdrawals resulted in a reservoir pressure decline of slightly over 100 psi. Predictions of future behaviour indicate that the water drive will not be of sufficient magnitude to maintain the reservoir above saturation pressure past 1953, and that, with natural depletion, the pool will be produced largely by a solution gas drive. Pressure maintenance by water injection has been considered and the possibility of raising the pressure to the original value of 1,050 psig is also discussed. INTRODUCTION WITH the discovery of the Lewduc pool, early in 1947, the Devonian limestone became the major geological formation contributing to Western Canada's rapidly growing petroleum reserves. Redwater, discovered in October, 1948, is now the largest known Devonian pool in Canada, with a recoverable reserve estimated at approximately 500 million barrels. Until recent years, the knowledge of the nature and characteristics of this type of limestone reservoir has been comparatively limited.

Jan 1, 1951

By J. L. Morning

During recent years, the Bureau of Mines has conducted an extensive investigation of the materials for making iron and steel. This work includes iron ore concentration, agglomeration, direct reduction of iron ores and concentrates, the production of pure manganese, chromium, and cobalt by electrolytic processes, the production of ferroalloys from low-grade domestic ores, and the development of special alloys to utilize these products. As a part of this general program, a Congressional appropriation allowed the con¬struction of an electric-furnace, semicommercial, ingot-producing plant at Shasta Dam near Redding, Calif. The primary objectives of the pilot plant were to determine the costs and operating problems involved in the production of steel and ferrous alloys in which sponge iron was used as melting stock, and to determine the physical properties of the materials produced. The pilot-plant equipment and the results of sponge iron-melting tests in the basic lined, electric arc furnace have been reported in previous publications.3/4/

Jan 1, 1953

By Y. Nakamura, T. H. Okabe, S. A. Sunkar, K. Nose

Ruthenium (Ru) is known as a platinum group element with a very small production volume. In fact, the worldwide annual production of primary Ru metal is only about 20-30 tons, and it depends on the amount of Pt produced, since Ru is a byproduct from Pt smelting. The primary uses of Ru are as a material for resistors, as a catalyst for electrode materials, and as a sputtering target for hard disk memory storage. In order to recover Ru from the spent sand-blasting abrasive media generated during the cleaning of the apparatus used for Ru sputtering, a hydrometallurgical recovery process using hypochlorite solution has been investigated. In this study, various types of recycling processes that are presently under development are also introduced, and their features and differences are discussed. The advantages and disadvantages of the new recycling processes are evaluated, and the possibility of establishing new recycling processes in the future is discussed from a multilateral perspective.

Jan 1, 2014

The Managalase area is remote and little visited by geologists or prospectors. Yet it holds the key to the tectonics and petrology of this part of Papua. The eastern Managalase plateau (M, Figure 1) lies between the Hydrographers andesite volcano (H) and Sesara shoshonite volcano (S) to the south of Popondetta on the Papua Peninsular. It contains over 30 small volcanic centres in an area of only 400 km2 . To the south and west lies the basic-utrabasic belt (B-UB) of the Morobe arc. This is the leading edge of oceanic plate obducted over the Owen Stanley Metamorphics during the lower Eocene time. To the east and southeast lies the Cape Vogel geosyncline where the western end of the Woodlark basin spreading centre enters mainland Papua. The extension of the spreading centre as a suture might pass as far as the southern margin of the Musa Coastal plain. A new pattern of plate tectonic motions has been determined by the global positioning system and the southern margin of the Woodlark plate has been redefined (Tregoning et al, 1998; Taylor, Goodliffe and Martinez, et al, 1999). The Managalase plateau is margined by two inferred faults. These outline a cusp protruding from the main basic-ultrabasic belt where these rocks are near the surface. The westerly arm of the cusp passes through the centres of the Hydrographers and Mount Lamington andesitic volcanoes. Mount Lamington overlies Quaternary alluvium and underlying Tertiary sediments (Arculus et al, 1983) but members of the basic-ultrabasic belt crop out on the southern flanks. The easterly arm of the cusp is an inferred shear zone (and ? fault) connecting up with the terminus of the suture on the Musa coastal plain. Movements on the two faults forming the cusp are thought to have produced the conjugate N-S, E-W faults on the plateau (Ruxton, 1966). To the east, and isolated, are the two large andesitic stratovolcanoes of Mounts Victory (V) and Trafalgar (T) which together form Cape Nelson. Mount Victory was last active in the 1890s. The Waiowa shoshonitic volcano explosion centres (W), last active in 1943 - 1944, lie near the suture adjacent to the actively rising Goropu mountains. Extension in these mountains is clearly demonstrated by the soil profiles being skeletal along a bounding fault and ageing uphill. The incision of small parallel ravines also dig deeper further upslope from the fault. To the south-east of Mount Suckling (K) the Dayman Dome is also an expanding mass. The Owen Stanley fault is parallel, and located to the south of the suture. The Mesozoic metamorphics form the backbone of the Papuan Peninsula. The intramontane Musa Trough is thought to date from the mid-Tertiary. At the eastern end of the trough Pleistocene and Recent ultrabasic breccias and alkali basalt crop out (Green, 1961).

Jan 1, 1999

By M. L. Requa

EVERY forward step in civilization brings with it an increase in population and increasing demand for raw materials. Modern civilization, because of its industrial development, depends more and more for its well-being on ample supplies of raw materials; the higher the type of that civilization, the greater its dependence. No fact is more obvious than that the raw materials should be put to use with greatest prudence and efficiency. National life is not a matter of a decade or a century. Conservation is no longer a matter for political discussion; it is a vital element in the future welfare of all nations. Unfortunately, to the minds of many, conservation means the locking up of natural resources, their arbitrary withdrawal, bringing about, in short, a condition of industrial stagnation. This has occurred in past centuries through misdirected governmental effort. Two eminent engineers have variously defined conservation as follows:

Jan 1, 1925

By H. F. Yancey

The Baum-type jig used so widely to clean bituminous coals has not been adopted for anthracite. If proved suitable for anthracite, its use might lower preparation costs in some plants. Cleaning trials on a Pennsylvania anthracite in a laboratory-size Baum-type jig were undertaken by the Bureau of Mines to provide indicative information that would be helpful in determining whether the cost of a full-scale installation would be justified. Clean coal surpassing standard anthracite specifications was obtained in all sizes from Stove through No. 5 Buckwheat. Recovery effi¬ciencies were acceptable down to 3/16-inch size, but there was excessive loss of coal in the finer sizes. Thus the fine refuse produced in a commercial plant might re¬quire retreatment. A comparative cleaning trial in a dense-medium pilot plant provided a recovery efficiency only l percent higher than obtained in jigging.

Jan 1, 1957

A wide range of drill holes and process streams are sampled for resource estimation, grade control, and contractual purposes in the minerals industry. However, despite the availability of training courses, conferences and both national and international standards on correct sampling practices, it is still surprising how often little attention is given to ensuring that representative samples are collected for analysis. The reason for this is that the responsibility for sampling is often entrusted to personnel who do not appreciate the significance and importance of sampling, with cost being the main driving force rather than whether the sample is representative of the material from which it was extracted. This seriously undermines the precision and accuracy of the analyses subsequently generated and can render the analysis process a total waste of time and money and expose mining companies to serious, potential, financial losses. Company management needs to reverse this situation and ensure that sampling is given the attention it deserves to generate representative samples for analysis.

Jan 1, 2010

By F. P. Hassani, H. B. Poorooshasb

"A kinematically admissible velocity field is applied to study the arching phenomenon in a cohesionless granular backfill placed between two rough vertical inflexible walls. The study is different from the previous works which are almost entirely based on statically admissible stress fields. It is shown that the development of arches is strongly influenced by the previous loading history of the backfill which controls the nature of the constitutive laws that govern the mode of stress deformation of the backfill. This preliminary study employs simple models in order to show the potential use of such an approach in evaluating and understanding mine backfill behaviour in the underground excavation. The pressure exerted on the floor supporting the backfill is also studied in some detail.INTRODUCTIONAlthough the importance of the design of mine backfill has been discussed extensively by a number of authors, i.e. Hassani et al. (1985), such theories have not as yet been incorporated in design criteria for underground mine backfilling operation . One factor that such theories must incorporate is the so-called arching action .The phenomenon of arching has been the subject of study by many researchers in the field of civil engineering and mining engineering. Among these scholars the works of Terzaghi (1943), Krynine (1945), Lusher and Hoeg (1964) and Handy (1985) are noteworthy. All these authors use a statically admissible stress field as a starting point to develop their theories. The approach taken by the authors of the present paper is completely different because they employ a kinematicallyadmissible velocity field. It is their belief that the arching phenomenon is closely linked to the interlocking of grains as manifested by the degree of dilatation of the granular mass when subjected to a shearing process.This paper is written in the following sequence. To define the interlocking quantitatively it is necessary to state the constitutive law governing the stress deformation characateristics of the granular mass. This is done in the next section as the law proposed by Poorooshasb and Pietruszazck (1985, 1986) is stated and simplified to suit the present analysis. Next the mode of formation of an arch in a simple system consisting of a mass of backfill sandwiched between two vertical rough walls of infinite extent is examined. The velocity field obtained from the above example is used to obtain solutions to two more complicated situations. The first situation assumes that the backfill is supported, in addition to the vertical rough walls, by a Winkler foundation at its base. The second situation assumes that the Winkler foundation has been replaced by a horizontal beam of uniform section and simply supported at its extremities. The findings of the study are summarized and their practical implications discussed in the concluding remarks."

Jan 1, 1989

By C. Kennedy, S. Jensen

Traditionally, mineral processing plants are designed to achieve the highest recovery of valuable material with limited regard for the cost of managing waste products-both solid and water components. As an industry, we are confronting ever more stringent environmental standards and lower grade deposits requiring more intensive processing. The most profitable processing route can, in fact, lead to costly issues downstream. Issues or risks associated with waste management include water treatment and handling and storage of potentially acid generating material. The capital and operating costs of dealing with these issues are significant and should be considered as a consequence of plant design and optimisation. The authors of this paper are involved with a number of projects where process operation changes offer opportunities to mitigate risks associated with water and waste management. Examples of these changes will be discussed along with the estimated benefits to the value of the project and reduction of long-term environmental risks. Process changes include 1) the application of in-plant water treatment as opposed to dealing with the entire tailings management facility and 2) the potential to reduce metal leaching and acid rock drainage through the preferential liberation of carbonate minerals in the grinding process.

Jan 1, 2014

By A. J. Giroux

"The use of Ishikawa cause and effect diagrams in an analysis of requirements for improving safety and productivity at Falconbridge's Strathcona Mill is presented. The analysis lead to numerous small improvements being made with the cumulative effect being a significant improvement in both areas.INTRODUCTIONMill management in the 90's involves the major requirements to improve both safety and productivity in the workplace. These objectives, once seen as unrelated or even mutually exclusive, are now accepted as being complementary. Managers, trained either on the job (coming up through the ranks) or in an engineering discipline followed by first and second line supervisory experience are now turning to methods developed in consumer product manufacturing to ensure that all the components are in place to ensure the ore processing facilities are safe and efficient.This paper shows how management at Falconbridge' s Strathcona Mill used the Ishikawa ""fishbone"" diagram ( 1) , a method further developed by Deming(2), to put into place a comprehensive safety and productivity process. The Ishikawa/Deming concept is that no one element or program will itself continually improve a process or service. It is only by examining and then improving all the elements that are involved in the process or service that continuous improvement is obtained. The process was built on the Deming principle of worker ownership where management is the facilitator for putting into place the mechanisms whereby workers can themselves improve the operation. The process is illustrated mainly by examples of the changes made in the hope that these may be of direct help to other operations."

Jan 1, 1993

By G. B. Harris, C. W. White

Cyanide has been used for the recovery of gold since the mid 1800s, but several jurisdictions have already banned its use, and environmental pressures are increasing to finding an alternative. Gold also forms chloride complexes similar to those of cyanide, but the use of chloride has never achieved widespread acceptance. This paper describes a chloride-based flowsheet, wherein the key unit process is the recovery and recycle of chloride ion. It is shown that the chloride-based flowsheet is competitive economically with the conventional cyanide-based flowsheets, and that it has a number of other advantages, particularly environmentally.

Jan 1, 2011

By R. Ward Stahl

This publication is a revision of Report of Investigations 5363 updated to reflect the improvement in fire protection at selected coal mines and contains suggestions on what may be considered good fire protective equipment, suggested methods of organizing the attack on fires at various locations underground, and helpful hints on testing and evaluating firefighting facilities.

Jan 1, 1968

In this study, we develop a detailed model of the likely future carbon footprint of primary copper supply. We develop a peak copper production model, based on a detailed copper resource data set, and combine this with a comprehensive life cycle assessment model of copper mining and milling to predict greenhouse gas emission rates and intensities of Australian and global copper production up to 2100. By establishing a quantitative prediction of both copper production and corresponding greenhouse gas emissions of Australian and global copper industry, we then analysed the emissions intensity of various energy input scenarios, such as business-as-usual, solar thermal electricity and solar thermal electricity with biodiesel. The Australian Government has an aspirational goal for long-term greenhouse gas emissions of an 80% reduction from the 2000 level by 2050. For the copper sector, this means moving from about 12.6 Mt CO2e in 2000 to a goal of some 2.52 Mt CO2e in 2050 (assuming equal emissions reductions across the economy). Based on the energy sources modelled, only the solar thermal plus biodiesel scenario was capable of achieving this goal at about 0.15 Mt CO2e, since the solar thermal alone scenario still includes normal petro-diesel as a major source of emissions. Overall, it is clear that there are abundant resources which can meet expected long-term copper demands, the critical issue is more the carbon (and environmental) footprint of different copper supplies and use rather than how much is available for mining. It is clear that the switch to renewable energy can have a profound impact on the carbon intensity of copper supply, even allowing for increased energy intensity as ore grades decline, and a complete conversion to renewable energy will position the copper sector to meet existing annual greenhouse gas emissions targets and goals.

Aug 1, 2013

By Patrick F. R. Murphy

The mechanization of platinum group metal (PGM) underground reef mining in South Africa has posed a challenge to mining engineers for several decades. This is primarily due to the shallow dip angles and narrow thickness (<1.1m) of the tabular orebodies mined, and the issues faced in developing reliable drilling, bolting and loading machines suitable for such hard-rock mining applications. Presently, mining is typically conducted using hand drills and scraper shovels. These methods, however, are intensive in terms of manual labor, and limited in terms of productivity, and improved methods are desired. This paper will review the technical features of a 4 tonne, low-profile, LHD for narrow-reef PGM mining, developed by EJC Loaders Division.

May 1, 2003

By Victor Costa de Mello Vasconcelos

O objetivo desse projeto é a preparação nanofolhas de óxido de níquel por calcinação e a formação de híbridos com nanopartículas esféricas de ouro e paládio. O trabalho focou na síntese de materiais com forma e tamanho controlados por meio de metodologias simples e ambientalmente amigáveis e na preparação de estruturas híbridas com dispersão uniforme entre componentes. Foram obtidos hidróxidos, óxidos e híbridos, cujos parâmetros de síntese (como temperatura, tempo de reação, entre outros) foram estudados. Uma vez caracterizadas, empregaremos as estruturas do tipo M/NiO (M = Au, Pd) como catalisadores nas reações modelo de oxidação do álcool benzílico e de redução do 4-nitrofenol, com o intento de estudar a natureza da interação metal-suporte.

Oct 30, 2017