Search Documents

By Ben C. Gerwick

This publication is intended to document recent innovations and technologies that have the best potential for effectively improving the quality of marine foundations while reducing the cost, time and risk of construction. Marine foundations originated in Neolithic times with the Swiss Lake Dwellers who constructed pile-supported houses, safe from invading tribes. The Queen of Babylonia built the first recorded bridge in 1500 BC across the Tigris. The foundations were large flat stones laid on the river bottom. About the same time in India, builders extended their water well techniques to the construction of ?well? foundations in the beds of their rivers. These were really the first open caissons; brick walls were built up in a circular ring while divers excavated sand from the bottom, sometimes at a depth of 100 feet. The Romans extended the clay-filled cribs of the Middle East to shallow cofferdams, which they sealed by underwater concrete made with pozzolanic cement from Mt. Vesuvius.

Jan 1, 2013

By George T. Faust, S. R. B. Cooke

"The Southern Experiment Station of the Bureau of Mines, United States Department of the Interior, in cooperation with the University of Alabama, is investigating the preparation of pulverized coal for fuel. In this study the relative amount of surface in various products and samples had to be assessed. Because of the familiarity with screens and because of the simplicity of using the inverse ratio of the opening for ascertaining the amount of relative surface in the respective sizes, screens down to and including 270-mesh were used. This choice was made in full cognizance of the irregularity of screens, but it seemed that if the same screens were used throughout all the tests the relative values would be satisfactory.In dealing with the subsieve sizes, pneumatic elutriation was used to make several fractions to extend the sizing analysis into the range of hypothetical screens. This kind of a sizing analysis was thought necessary because it is familiar to all operators, and, furthermore, it is amenable to several ways of plotting curves that bring out the characteristics of various coals and various methods of grinding.The method of obtaining the data from which to set up the hypothetical screen scale is the subject of this paper. It consists in determining the average projected area of the particles in the respective elutriated products. By extending the ""area method"" to sieve sizes, a factor is found that may be applied to the subsieve sizes, and thus the scale is projected in a regular manner. This method avoids contentions about specific surface and steers clear of ""average diameter"" except as material sized on screens may be said to have an average diameter."

Aug 1, 1939

By Mingfei He, Yude Gao

"The leaching kinetics was studied during leaching of indium-bearing zinc oxide to recover indium. The effects of temperature, sulfuric acidity, particle size, stirring rate on dissolution rate of indium were investigated. Results showed that the leaching process was controlled by chemical reaction at the condition of low sulfuric acid concentration. While the acidity increased to 1.8 mol/L, the leaching process was transformed into an internal diffusion controlling model . The corresponding value of reaction orders under low acidity and high acidity were 1.194, 0.156, respectively. Further calculation results indicated that the leaching reaction activation energy was only 10.97kJ/mol under the condition of high acid. The leaching rate constant was inversely proportional to the square of particle size, while the effect of stirring rate on leaching process was insignificant. The leaching process can be enhanced by increasing the temperature and acid concentration, as well as the decrease of particle size. And a final kinetics eqution was proposed. KEYWORDS Indium, extration, leaching kinetics, zinc oxide INTRODUCTION Indium[1,2] plays an important role in many aspects of living and industrial production owning to its special physical and chemical properties. The reserve of indium is rare on the earth, and most of indium is distributed in some other minerals[3]. Some researchers [4,5] have proposed that indium mainly substitutes for the lattice of other minerals by isomorphous. Therefore, the extraction of indium should take into account of the production technologies of those minerals to comprehensively recover the valuable metals."

Jan 1, 2018

By S H. Burgmans, B Anderson

This paper aims to define the specific challenges relating to dredging fine tailings from an above ground storage facility for transferral to a mined-out pit. In addition, it compares dredging and mining perspectives on dredging of fine tailings.

Jul 1, 2021

By Z. Ruetz

Portable X-ray fluorescence (pXRF) analysis has been widely adopted in the geochemical and environmental field as a cost-saving alternative to standard analyses. This paper outlines the efficacy of a method for indirectly quantifying organic copper content in solvent extraction circuits via stripping of the chelated metal with concentrated sulfuric acid in a single contact and subsequent pXRF aqueous analysis. pXRF analysis is common within the mining industry but presents unique challenges with liquid analysis, the most prevalent of which are briefly discussed. This method was developed specifically for mining operations with regional constraints and limited resources. Providing an in-field alternative to flame atomic absorption spectrophotometry and inductively coupled plasma optical emission spectroscopy, this entirely mobile XRF analysis method produces consistent and accurate results within minutes and at a fraction of the cost.

Jan 1, 2023

By L. W. Blau

PERHAPS the most important event f or exploration geophysics in 1940 was the publication of three textbooks : "Geophysical Prospecting for Oil," by L. L. Nettleton ; "Exploration Geophysics," by John J. Jakosky; and "Geophysical Exploration," by C. A. Heiland. The literature had grown so bulky, and such a long time had elapsed since the publication of the texts by Ambronn and Eve, that treatises covering exploration geophysics comprehensively in all its branches and giving literature and patent references were sorely needed. This need has been satisfied admirably in these textbooks, and geophysicists owe the authors a debt of gratitude. In 1940, geophysics came of age. A conference on applied nuclear physics was held at Massachusetts Institute of Technology from Oct. 28 to Nov. 2. Several papers on geophysical subjects were presented at this meeting. Geophysical activity has decreased in all parts of the world except perhaps in Canada where, under the stimulus of the war's increased demands, prospecting for oil has increased. However, even there the war has had a seriously adverse effect on prospecting for ores and upon the promotion of new properties, although activity in producing and near-producing mines has been stimulated.

Jan 1, 1941

The Mt Sinivit gold project is located approximately 50km SSW of Rabaul in the Baining Mountains of the Gazelle Peninsula, East New Britain Province. The deposits were discovered in mid- 1983 and form part of a larger 26km long zone of variably aurif- erous quartz veining. There are no surface indications or previ- ous records of any prospecting activity or production from the region. The Mt Sinivit deposits consist of a series of oxide and sulphide reserves and resources contained in the Wild Dog (South- ern, Central and Northern oxide zones; Northern sulphide zone) and Kavursuki veins. The proposed exploitation of the oxide reserves by a series of small-medium sized open pits has been fostered by the PNG Department of Mining & Petroleum (DMP) as part of a government policy to encourage the development of a small-medium sized mining industry in the country. The aim of this paper is to document the steps and procedures involved in obtaining the grant of a Mining Lease emphasising the time and the expenditures required during each step of the approvals process for the Mt Sinivit project.

Jan 1, 1997

By C Kusi-Manu, E Nyamusika

Geita Gold Mining Limited (GGML) is owned and jointly managed by Ashanti Goldfields Company (Ghana) and Anglogold (South Africa). The mine is currently one of the largest gold producing open pit operations in Africa producing 620 000 ounces of gold and mining in excess of 70 000 000 tonnes of material per annum. The mine currently has 2000 full time employeeÆs and a mine life in excess of 12 years. Geita Gold Mine is comprised of 11 different gold deposits situated in the Lake Victoria Goldfields of North Western Tanzania (Figure 1). The gold deposits are primarily associated with banded ironstone formations within an Archaean greenstone belt. Current global resources, including Inferred, stand at 129.5 million tonnes grading 3.91 g/t (16.2 M oz). Open pit reserves total 70.4 million tonnes grading 4.16 g/t (9.4 M oz). The majority of the gold resource is hosted by the three deposits (Nyankanga, Lone Cone and Geita Hill) within the æGeita TrendÆ a large and continuous (>4 km long) mineralised zone (Adofo, 2002). Geita Gold Mine commenced operations in June 2000, as the second large-scale open pit gold mine in Tanzania. The new workforce of 800 people had no previous experience in open pit gold mining. Since the start of the operation, Geita Gold MineÆs management ambition was to become a world leader in the application of best practice in all technical disciplines and in operational success. Staff development and training was identified as one of the major components in the company achieving its aim. Geita Gold MineÆs management has committed the necessary training staff, resources and the commitment of over $US 1 M a year to staff training and development programs for 2003 and 2004. The process and management of Geita Gold MineÆs mining geology staff training and development program is presented in this paper.

Jan 1, 2003

By B Vietnieks, N Widmer, L White, E Tata, J Natukunda, D C. Ilouga, J P. Tyler

The Republic of Uganda aims to exploit its’ significant, un-developed iron ore resources to supply the required raw material for developing its’ iron and steel industry across all the stages of the supply chain. Large prospects of iron ore exists in Uganda in the eastern (Tororo) regions and southwestern (Kisoro-Kabale) regions of the country. The Kisoro-Kabale iron ore projects covers mineralisation in hematitic banded iron formation (itabirite) in the north-eastern Congo-Tanzania Craton; covering ten Iron ore prospects. The prospects include Kamena, Karukara, Nyamiringa, Kyanyamuzinda, Rugando, Katagata, Rwengongo, Kijuguta, Kihumuro and Katuna. High-grade hematite ore prospects in south-western Uganda have known grades ranging from 55 per cent to 68 per cent iron ore content with an exploration target estimated at over 500 million tonne (Mt). Small scale production of iron ore from the south-western regions provide raw material to existing steelmaking and direct reduction iron ore plants located in the Jinja and Iganga districts of eastern Uganda. Large quantities of iron ore and other steelmaking raw material, however, are required to be imported into Uganda due to the limited exploration and development of their own iron ore mining operations. A joint collaboration between the European Union (EU), the Department of the Geological Survey and Mines (DGSM), Ugandan Ministry of Mines in partnership with Australian drilling and mining consultancies, ADT Africa and Kalem Group as a EU funded project was undertaken during November 2022 and September 2023. Exploration and evaluation of the ten iron ore prospects in south-western Uganda was undertaken through geological mapping, drilling, assaying, and technical studies with the view to attract investment for the development of Uganda iron ore mining and steelmaking industry. The collaboration developed mineral exploration policy, guidelines and standards, an iron ore exploration manual, a geological data management policy, and to support the sustainable development of iron ore mining in Uganda through building the capacity of local Ugandan geology and mining personnel through the transfer of knowledge and expertise from experienced iron ore experts. The quantification of these resources is an important first step in assessing their economic potential and attracting mining investors. This paper presents an overview of the investigation program and the preliminary results as an important first step in attracting mining investors to this exciting new iron ore province.

Sep 18, 2023

By Charles M. Mason

The Bureau of Mines evaluated equipment and procedures for drop-weight testing of explosive liquids as prescribed by Test 4) a widely used method. It was demonstrated that partial ignitions, originally designated as negative results, should be designated positives; it was also shown that wear or erosion of the sample cups and the type of mount used for the apparatus had important effects on the results. Relative sensitivity as measured by Test 4 was found to vary slightly with temperature. The Bureau also designed a fixed 2-kg weight and associated electromagnetic release, which subsequently were incorporated as standard in a revision of Test 4. The original concept that the test involves only adiabatic compression was found to be an oversimplification; an alternate mechanism for the initiation process is proposed in which due consideration is given to the effects of cavitation and microjets.

Jan 1, 1966

By Mi Chung

T HE ore-dressing problem at Tul Mi Chung is complicated by the unusually complex nature of the ores. These come from replacement ore- bodies in limestone at the contact with a granite batholith, and contain copper, gold, silver, bismuth, molybdenum, iron, arsenic, zinc, and lead, the first two metals constituting the principal sources of profit. Iron is present as pyrite, magnetite, and hematite. Arsenic occurs both as mispickel and lollingite (FelAsa), the latter carrying a certain amount of finely divided gold. The gangue minerals are those typical of limestone con- tact-metamorphism and include a large percentage of garnet, together with diopside, serpentine, calcite, epidote, zoisite, actinolite, 'mica and other minerals. A part of the gold occurs in a free state; some is combined with chalcopyrite and lollingite, and a consider- able proportion is contained in the pyrite. Researches towards the improvement of recovery have been energetically conducted since 1915. Amalgamation, gravity concentrating tables, vanners, can- vas plants, etc., have all been tried and discarded in favor of flotation. It was very quickly established that fine grinding was essential for satisfactory recovery. This was and is still accomplished in Hardinge ball and pebble mills. A comparative test showed that when the ore was crushed to the point at which it contained 20 to 26 per cent. coarser than 100 mesh, the gold recovery was only 55.9 per cent., whereas when crushed so that only 11 to 15 per cent. was coarser than 100 mesh, the gold recovery was increased to 82.5 per cent. No particular difficulty was ever experienced in making a satisfactory recovery of copper but the losses in gold were considered serious and led to the investigation described in this paper.

Jan 1, 1924

By K. C. Dean

During the investigation of the occurrence of manganese deposits in western United States, the Bureau of Mines collected 2-ton samples from three oxide manganese ores in the Columbia and Elberta Mining Districts, Tooelo and Juab Counties, Utah. To determine the amenability of these ores to standard ore-dressing methods: of concentration, extensive laboratory tests were made. The Wildcat property, one of those sampled, is 7 miles east of Fairfield, Tooele County, Utah. The ore is described as a replacement deposit and occurs along fracture and bedding planes of shale and limestone. Experimental work was done on a sample taken from a stockpile at the mouth of the shaft. The Wildcat manganese ore is intermediate in grade (25.7 percent manganese) and contains clay as the principal gangue constituent. A high-grade product was obtained with high recovery of Manganese by simple washing.

Jan 1, 1949

By Edward E. Johnson

The U.S. economy boomed in 1965, completing its fifth consecutive year of expansion. Although the advance was somewhat irregular, previous records for production, sales, employment, and income were topped. During the first few months of 1965, as the economy recovered from the depressing effects of the automobile strikes of late 1964, increases were unusually large. The gains moderated in early spring, but were stimulated at midyear by sharply rising capital outlays, excise tax cuts, in? creased Social Security payments, and accelerated Viet-Nam defense expenditures. Gross national product (GNP) in cur-rent dollars rose $49.5 billion or 7.8 percent, to a total of S681.2 billion. In constant dollars (effects of price changes eliminated), GNP increased 5.9 percent, a rate considerably higher than the historical postwar annual average growth of 3.5 per-cent. Demand increased in most final markets and was especially strong for business fixed investment and consumption expenditures. With the exception of construction, most of the increases in GNP were real, since prices increased less than 2 percent.

Jan 1, 1966

Paper presented at the Mining Institute of Scotland's annual general meeting held in Glasgow, 8th April 1916. Although there is nothing novel or difficult about the sinking described, circular shafts are not numerous in Scotland so the details connected with such a sinking may be of interest. The shaft was sunk at Dykehead Colliery, Larkhall, which has been worked for over 50 years from the upper seams. It became necessary to sink another shaft to serve as a replacement downcast, by which the output might be maintained and some of the lower seams won. As the sandy clays regularly caused bulging into the rectangular shaft and sinking of the surrounding ground it was decided to make the new shaft circular and to enclose its mouth in a foundation-block of concrete resting on the solid clay. Details are given of the sinking, brick seating and lining, kettle strike, water-rings and doorhead lintels as well as the permanent fittings, winding gear and the cages themselves

Dec 1, 1916

By Eero Pokki

The Päijänne Tunnel is being constructed to conduct raw water from Lake Päijänne to the Helsinki Metropolitan Area. The length of the tunnel will be 120 km and the cross-sectional area is 15.5 sq m. Excavation started in 1973 and will be completed in 1982. 94 km of the tunnel have been constructed from Lake Päijänne towards Helsinki. The construction has advanced according to plan, and due to Finland's hard bedrock there have not been any great surprises. When completed, the tunnel will meet the water requirements of the Helsinki Metropolitan Area for a long time in the future because, with a free fall of 36 m, 9.6 cu m/s of water can be conducted through the tunnel from Lake Päijänne to the Helsinki Area. With pumping it will be possible to obtain a flow of 15 cu m/s, although at first the discharge will only be 5 cu m/s. The tunnel was partly taken into service as early as March 1979 when it was possible to conduct water to the municipalities north of the Helsinki Area. It is already possible now to conduct water to Helsinki, too, but from the Korpimäki pumping station onwards it must be done through the River Vantaa, which is polluted. When the tunnel is completed in 1982, good quality water can be conducted from Lake Päijänne to the Helsinki Metropolitan Area through a continuous rock tunnel. The cost estimate in 1973 was $ 88 million while it is now $ 90 million notwithstanding high inflation. AREAS NEEDED FOR CONSTRUCTION The areas needed for construction were bought through voluntary deals. Areas of 4 - 5 hectares were bought along the tunnel line at about 5 km intervals. The excavation of access tunnels was started from these places, and the crushed rock from the main tunnel was also transported there. However, it was not necessary to buy the area

Jan 1, 1979

By B. Hearn, Malcolm J. McPhersqn

Since 1993 Inco Ltd. has been using wet shotcrete at Stobie Mine. Through an evolving process the mine has reduced the thickness and fiber content of its steel fiber reinforced (sfr) shotcrete. However, the shotcrete support is used without any other type of ground support. A process referred to as bolt less shotcrete. Boltless shotcrete is used as the primary ground support method in development headings when the sub level caving front passes through the development drifts which now serve as migrating ore draw points. Although there are references of drifts and tunnels supported by shortcrete only, written accounts are rare. The empirical nature of most underground support designs makes them of limited value in a boltless environment. Considerable amounts of material testing and insitu trials have been completed in order to estimate material property strengths. Material testing, for adhesion, flexural strengths and compressive strength along with observational insitu data have been used to evaluate the performance of shotcrete. Punch tests on panels have also been undertaken in order to gain insights on the limitations of the two dimensional testing common to the laboratory. All these design aspects have been successfully utilized to design an efficient ground support process.

Jan 1, 1998

By C Itotoh, K O’Halloran, L Karlson

Global methods used to explore for minerals have progressed relatively slowly since the development of the first diamond core drill in 1863. Since then, key developments such as wireline geophysics (1920s), the tricone drill bit (1930s) and aeromagnetic surveys (1940s) all occurred in response to global events. In this project, BHP’s WAIO Geoscience operations team hypothesise that a global movement towards a greener future as well as an increasing intolerance for safety events will drive another step change in exploration methods. We have leveraged our relationships with exploration contractor partners and industry leaders to develop a realistic vision for 2033 and beyond, where drill rigs, earthworks and geophysical units are operated and maintained remotely; emissions of dust and waste are eliminated; hazardous energy sources are controlled; procurement is based on sustainability rather than cost and carbon emissions are tracked with the same rigour as production metrics. We have combined these visions into a series of graphical illustrations with the aim of inspiring ourselves, our vendors and our peers to collaborate further on producing a step change in our industry.

Sep 18, 2023

By P. Schloth, H. van Swygenhoven, N. Chobaut, J-M. Drezet

"In the current trend toward thicker aluminium plates, a major concern is the stress build-up during quenching which causes distortions during machining. Indeed, cooling rates are not high enough, especially at the core of such thick plates, to prevent any precipitation and quench induced precipitates lower the hardening potential. Multi-scale modelling is required when predicting macro-scale stresses after quenching for thick heat treatable aluminium components. The reason is the instantaneous strong coupling between phase precipitation at the nano-scale and material hardening due to precipitation or softening owing to solute depletion at the microscale. For thick parts, quenching intensities decrease when going from the skin to the core of the component, thus introducing a gradient of nanostructure and consequently a gradient of mechanical properties. In addition, large thermally induced deformations lead to high macroscale residual stresses although part of them is relaxed by plastic deformation. These stresses have been measured in water quenched thick plates of 7040 and 7449 aluminium alloys using neutron diffraction and layer removal techniques and the results when compared with a thermomechanical finite element model of quenching highlight the influence of precipitation.IntroductionIn the processing route of heat-treatable aluminium alloys (AA), a critical step is quenching from the solutionizing temperature. High cooling rates are desired, as they avoid formation of coarse precipitates, which reduce mechanical properties. Fast quenching, however, cannot be achieved in the centre of thick components, where the quenching rate can be more than one order of magnitude lower than at the surface. The existence of a thermal gradient between core and surface leads to a differential thermal deformation which is accommodated by elastic and plastic deformation to comply with the compatibility of deformation. Whenever the material yields, especially at high temperature when the yield strength is low, residual stress remains after quenching due to the irreversibility of plastic deformation. After quenching, the plates are in a state of residual stress that causes unacceptable distortions during machining and may reduce service life drastically. Since stress relaxation is negligible during ageing treatments [1 ], agehardened aluminium parts are usually stress relieved prior to ageing. This is typically achieved by applying plastic deformation: stretching from 1.5 to 3 % in the rolling direction (L) can reduce the internal stresses by a factor of approximately 10 [2, 3]. However, complex geometries or thicker components like thick sheets require other approaches. Reducing the quenching rate by using boiling water for instance leads to lower residual stresses [1, 4]."

Jan 1, 2013

By M. R. Geer

Traditionally, fine coal is more troublesome than the coarser sizes at every step of the coal-preparation process--screening, cleaning, dewatering, and drying. Therefore the present trend toward a higher proportion of fines in the run-of-mine product, brought about by changes in mining practice necessitated to increase productivity, has added greatly to the task of preparing coal for the market. One of the more difficult and costly problems involved is that of recovering fine solids from the washery water. These fine solids should be recovered in the interest of conservation, and they must be removed to provide recirculating water of proper quality. If there is a plant effluent, it must meet increasingly stringent requirements against stream pollution. Vacuum filtration has been used for years at a few plants to recover the extreme fines, but its additional cost discouraged general adoption until recently. Now, with growing emphasis on better solids recovery, filtration is becoming more widespread. Many coal slurries filter readily, giving high cake rates and clean filtrates. Others, however, particularly those containing either a high proportion of material finer than 200-mesh or an appreciable amount of clay, are much more difficult to filter. Many of these refractory slurries can be rendered more filterable by flocculation. A previous report of Bureau of Mines research dealing with flocculation alone was published in 1940.5/

Jan 1, 1959

By K. J. Shoop

This study investigates the use of a horizontally-baffled column (7.6 cm inside diameter by 344.2 cm high) to reduce the ash content of a high ash bituminous coal. Tests were carried out to determine how the baffled column responded to changes in feed rate, reagent dosage, and feed quality, and to compare its performance with a conventional column installation in an operating plant. In this paper, the results of this investigation will be reviewed and discussed.

Jan 1, 1997