Search Documents

Discussion of a paper of S. S. Rummy and W. F. SCHWEDES, presented at the Pittsburgh meeting, October, 1914, and printed in Bulletin No. 94, October, 1914, pp. 2613 to 2635. K. A. PAULY, Schenectady, N. Y.-I have seen this installation and I wish all those interested in the question of electricity as a mine pumping agent could see it. It is not only a model for mine installation, but might well serve as a model for any electrically driven pumping plant. I think I am correct in saying that the pumps are the largest electrically operated centrifugal pumps in mine service in America. I talked with Mr. Rumsey in Duluth just before coming here, and he told me that the actual tests of the equipment as installed checked very closely with the shop tests; that the water delivered by the pumps was slightly in excess of the guarantee, something like 3 or 4 per cent., and that no troubles except of a very minor nature had been experienced with the installation from the start. One point which has been brought out by Mr. Rumsey, and by others who have looked into this question, is the marked saving which' can be made by the application of electricity to pumps, especially to the main sump pumps. The pumps are always located a long distance from the boiler plant and the losses in the steam mains are large. While many of the steam pumps are of a very high grade, yet the tests seemed to indicate that the steam consumption is extremely large. The reduction in operating cost of one small installation which I. have in mind pumping against a head of approximately 2,000 ft.-which by the way was a reciprocating pump-reduced the pumping cost to the neighborhood of one-fifth of the previous steam cost. . The high steam cost was probably due to leakage in the engine and the loss in transmission in the mine, the pumps being located almost half a, mile from the boiler plant.

Jan 4, 1915

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By A Smith

Rock masses usually exhibit scale dependent mechanical properties primarily due to presence of discontinuities and their inhomogeneous nature. One of the essential preconditions for selection of appropriate strength and deformation parameters of a rock mass in relation to tunnel design is assessment of the scale of the joint network relative to the scale of excavation. In tunnel design practice, scale effects are estimated indirectly using small-scale unconfined compressive strength (UCS) tests and rock mass classification based empirical correlations. Large-scale UCS tests have the benefit of direct assessment of anisotropic and scale dependent properties of a rock mass.This paper presents results of a large-scale UCS test on a jointed siltstone. A 450 mm diameter sample with inclined bedding planes was cored and tested in uniaxial compression until failure with load and displacement measurements. The aim of the test is to determine strength and deformation parameters and correlate them with results of small-scale UCS tests of the same sample. The relationships between the small-scale and large-scale rock mass parameters were validated against published correlations from the literature.

Mar 8, 2011

By Jerrold J. Marcus

United states reserves of oil and gas have been steadily declining while consumption of petroleum products has continued to increase. The nut result has been an ever increasing shortfall between supply and demand. This imbalance has been made up by imports of both oil and gas causing a strain on the United States Balance of Payments. To complicate the situation further, exporting nations have recently formed a cartel and dramatically increased the selling price of petroleum products. To meet U.S. energy demand, increased attention has been drawn to the production of synthetic oil and gas from coal. To date, considerable research has been conducted and is continuing on various processes for liquefaction and gasification of coal. Some of these processes are now in the pilot plant stage and at least one demonstration plant has been proposed. The coal conversion complexes envisioned will be very large, requiring substantial capital investments and abundant reserves of coal. Coal production to feed these proposed complexes has been estimated on the order of 75,000 tons per day. With the viability of these projects becoming economically attractive, the Office of Coal Research initiated a contract with Fluor Utah to determine and define the problems of surface mining coal at very high mining rates, under varied physical, geographic, and climatic conditions. The flow of recent events in the Middle East has created a greater sense of urgency for this study.

Jan 1, 1975

By H. H. Johnson, Eric W. Johnson

A newly developed ac technique was used to measure the electrical-resistivity changes associated with both cyclic stressing and subsequent annealing of high-purity and OFHC copper. The early stage of push-pull fatigue was explored at 293° and 4.2°K, with stresses chosen for an expected fatigue life of 2 to 8 X 105 cycles. For high-purity copper, fatigue at 293°K was accompanied by an initial increase in resistivity. After about 5000 stress cycles, no further increase was observed. Annealing studies showed that the resisticity increment could be accounted for solely in terms of an increased dislocation density, to about 2 x 1010 disl pev sq cm. Fov 42°K fatigue, however, the resistivity increased continually, with no evidence of saturation, as approximately (No. of stress cycles)1/4. This is intevpreted to result from both dislocation multiplication and vacancy production; estimated vacancy concentrations are 10-4 to 10-9. The continuous resistivity increase was inhibited by interspersed annealing treatments at 293°K, which also raised the level of the stress-strain curve. These effects are attributed to annealing of vacancies into dislocation loops. In contrast, OFHC copper fatigued at 4.2°K showed saturation of electrical vesistivity after only a few hundred cycles, and it appeared that vacancies annealed out completely between 77° and 293°K. MaNY observations suggest that both dislocation multiplication and point-defect production are important aspects of fatigue deformation. An increase in dislocation density with number of stress cycles has been demonstrated or implied by several experimental techniques, including optical metallography with lithium fluoride,' electron microscopy with copper,2 thermal conductivity of Cu-Zn alloys,3 and peak-stress measurements during cycling at constant plastic strain amplitude.4,5 At low amplitudes and/or stresses saturation of fatigue hardening and dislocation density occurs early in the expected fatigue life,4-6 frequently by a few hundred cycles. The evidence for point-defect production is somewhat less extensive, but it is nonetheless persuasive. Rosenberg7 reported briefly that, for equal stresses, copper fatigued at liquid-hydrogen temperature displays an increase in electrical resistance some ten times that which accompanies unidirectional stressing. Further, the extra resistance saturates after a few hundred stress cycles, and does not anneal significantly until a temperature of about 170°K is attained.' Point-defect production during fatigue is also suggested by 1) the softening during cyclic stressing of initially strain-hardened polycrystal-line copper9, 2) the strong temperature dependence of the yield strength of fatigue-hardened mono- and polycrystalline copper,579"0 and 3) the influence of intermediate annealing upon slip-band formation in copper fatigued at 90°K.8 It is evident that characterization of the fatigued state requires a knowledge of both point-defect and dislocation densities. For this purpose electrical-resistivity measurements are useful, but they are difficult to perform because of geometric limitations. Push-pull fatigue is necessary to obtain a macroscopic ally uniform deformation over the specimen cross section; however, the specimen must then have a low slenderness ratio to avoid plastic buckling, while the standard dc resistivity technique requires a very slender specimen for

Jan 1, 1965

First, a classification of the various primary sources of feed materials for the production of cobalt is presented from a mineralogical point of view : sulfides, arsenides, sulfo-arsenides and oxide minerals. Each of these cate- gories will be characterized by its behaviour towards concentration methods, taking account of the presence of the associated minerals of other metals and of the nature of the gangue minerals. Then, for each category of cobalt bea- ring ores, typical flowsheets of treatment will be presented and discussed and the characteristics of the cobalt concentrates produced will be under- lined having in view their subsequent processing by pyro - and (or) hydrome- tallurgical methods.

Jan 1, 1988

By G. Akdogan, S. M. Bradshaw, A. P. Van Wyk

In the mineral processing industry, Ni-Cu-Fe-S converter matte is leached to remove base metals from a concentrate containing platinum group metals (PGMs). We investigated the atmospheric leaching process to develop a better understanding of the leaching behaviour of the base metals (Cu, Fe, and Ni) and the PGMs, in particular Ru, Ir, and Rh with respect to key process variables, acid concentration, and Cu concentration under oxidative and non-oxidative conditions. With oxidative leaching, a higher initial acid concentration resulted in higher Cu, Ni, and Fe extractions, as well as faster leaching reaction rates. A higher initial acid concentration also resulted in faster precipitation of Cu, Ru, and Ir under oxidizing conditions. Under non-oxidative conditions, Ni and Fe extraction was much slower, and the effect of initial acid concentration on Cu precipitation was less pronounced. The initial Cu concentration had a slightly smaller effect on the leaching behaviour of Fe and Ni, as well as precipitation of Ru, Ir and Rh. Moreover, a higher initial Cu concentration suppressed both Ni and Fe leaching and had a slight inhibiting effect on the precipitation behaviour of Cu, Ru, and Ir.

Nov 1, 2021

By N. G. Johnson

ALL of us are only too familiar with the fact that first the defense program, and finally the war, required vastly increased production from existing sources, and the discovery and development of new sources of minerals and metals. For this vast program, the explosives industry was well prepared. I use the term "well prepared" to cover all the phases of explosives service, which include formulation, design, manufacture, distribution, and application.

Jan 1, 1944

By Alexander Karim

This paper reviews the growth pattern in bauxite and alumina production, and primary aluminum smelting through 1980. Because the alumina and primary metal are intermediate products of the major integrated aluminum companies, it is not possible to determine their production costs. The costs indicated in this paper are order of magnitude costs based on published figures and the market price of these products. The conclusions in this paper indicate the general pattern of growth in the aluminum industry and are not meant to be a substitute for the feasibility and economic studies that are needed for individual bauxite mining, alumina refining and aluminum smelting projects.

Jan 1, 1968

By Weiren Lin

The Mw 9.0 Tohoku-Oki, Japan earthquake occurred on 11 March 2011 produced a maximum coseismic slip of >50 m near the Japan Trench. To investigate why the plate boundary fault between the subducting Pacific Plate and overriding North American Plate which caused the earthquake had such unprecedented large coseismic displacement and slipped to the trench, Integrated Ocean Drilling Program Expedition 343 called Japan Trench Fast Drilling Project (JFAST) drilled three boreholes at Site C0019 through the earthquake fault about one year after the earthquake. Borehole C0019B dedicated to loggingwhile- drilling (LWD) penetrated ~850 meters below seafloor (mbsf) at a water depth of approximately 6890 m. The plate boundary fault is located at ~820 mbsf in the borehole and has been identified as the slip zone during the Tohoku-Oki earthquake. Borehole wall resistivity images obtained from LWD show that drilling induced borehole breakouts are available in a wide depth range above the fault but are not available below the fault. Breakouts are reliable indicators of the orientations of current maximum and minimum horizontal stresses and can also be used to constrain the horizontal maximum and minimum stress magnitudes. As results of breakout analyses, the maximum horizontal stress orientation highly varied in the upper part of the borehole, but has a clear preferred orientation in a northwest – southeast direction in the deeper part just above the fault. This orientation is approximately parallel to the direction of the Pacific Plate subduction. Stress magnitude constraints indicate that the post-earthquake stress states in the hanging wall are either in or close to the normal faulting stress regime. By inferring the pre-earthquake stress state and comparing with the constrained post-earthquake stress state, a significant coseismic stress change was interpreted. The stress change suggests an active slip of the frontal plate-interface consistent with coseismic fault weakening and a nearly total stress drop.

Jan 1, 2015

By A. A. Zatout, G. H. Sedahmed, T. M. Zewail, M. H. Abdel-Aziz, B. S. Ibrahim, E-S. Z. El-Ashtoukhy

In this work, the possibility of intensifying the cementation process in stirred vessels was studied by using the perforated baffles as turbulence promoters; the cementation reaction of Cu+2 on Zn was selected as a model. Zn was used in the form of a sheet lining the inner wall of an agitated vessel. Parameters considered are initial concentration of Cu+2, solution temperature, impeller rotation speed, and impeller geometry. Within the present range of parameters studied, the rate of cementation was found to increase with increasing initial concentration of Cu+2, solution temperature, and impeller rotation speed. At the same rotational speed, a flat turbine gave a higher rate of cementation than a 45° pitched turbine. The present suggested that baffles’ geometry gave superior performance in terms of mass transfer of copper cementation compared to the conventional baffle geometry. All parameters that affect the rate of cementation were correlated in the form of dimensionless equations suitable for the design and performance prediction of the agitated vessel. Potential applications of the obtained results in the field of hydrometallurgical processes and wastewater treatment were discussed.

Jan 12, 2021

By H. E. Powell

This Bureau of Mines study describes two processes for recovering zinc, copper, silver, and iron from the magnetic fraction of a waste generated by the primary smelting of zinc in horizontal retort distillation furnaces. The laboratory-scale procedures include reduction melting to produce a high-copper iron and matte smelting to produce a copper-silver-iron matte and metallic iron. Zinc is fumed in each process and recovered as the oxide. Direct reduction melting yields a metallic iron high in copper and a small rich matte from the sulfur contained in the waste. The products of the second process are a matte containing essentially all of the silver, about 80 pct of the copper and 37 pet of the iron, and an iron-copper alloy containing all of the remaining copper. Extraction with metallic lead or sodium sulfate recovers essentially all of the copper from the molten high-copper iron and yields an acceptable foundry iron.

Jan 1, 1973

By F. P. Morawski, J. E. Schelske, J. R. Geddes, B. R. Eberts, D. M. Wilson, J. D. Jeffries

"The Griffith Mine is located 200 miles northeast of Winnipeg and is 30 miles south of Red Lake, Ontario. Owned by The Steel Company of Canada Limited and managed by Pickands Mather & Co., it has an annual rated capacity of 1.5 million tons of high-grade iron ore pellets with an analysis of 66.3 per cent iron and 4.5 per cent silica.Development of the mine and construction of the plant got underway in January of 1966 and operations began in February of 1968. The orebodies outcrop on the shore of Bruce lake and run under the lake. The ore in its crude form is a metasedimentary low-grade magnetite and occurs in a highly folded banded formation. The average iron analysis of the crude is 29 per cent and the over-all weight recovery is 32 per cent.In order to mine the portion of the orebody under the lake, the soft varved clay on the lake bottom was hydraulically dredged and a dyke constructed of rock, with till used to provide an impervious seal on the lake side of the dyke, prior to dewatering.Mining is carried out by conventional open-pit tech-niques. Ore dressing is achieved by combining one crushing stage and a two-stage grinding system, with beneficiation by magnetic separation, hydroseparation and flotation. Agglomerating is done with conventional balling drums and pelletizing is carried out in shaft furnaces.Of interest and discussed in detail are the 32-foot autogenous cascade mills ."

Jan 1, 1970

By E. P. Klier, Taylor Lyman

THE structures formed when austenite is quenched to subcritical temperatures and allowed to transform isothermally have been the subject of intensive study since the work of Davenport and Bain.1 Isothermal transformation diagrams summarizing the results of many of these studies have become widely familiar to metallurgists. Of particular interest to metallographers are the dark-etching, acicular products of transformation formed by isothermal reaction below the temperature of maximum velocity of the austenite to pearlite reaction. These products, the bainite structures, can be formed in a wide variety of steels. However, the constitution of bainite is not well understood and divergent views have been expressed as to its mode of formation. In this investigation a combination of dilatometric, microscopic and X-ray methods has been brought to bear upon the problem in the hope of some elucidation of the bainite reaction as it occurs in hypoeutectoid steels. MECHANISM OF BAINITE FORMATION Davenport and Bain1 considered the mechanism of bainite formation to consist of two steps-an allotropic transformation followed by precipitation of carbide. The separation in time of the two processes was considered to be very slight in the upper temperature range and very marked at temperatures just above the martensite range. This concept has been restated by Vilella, Guellich and Bain2 in the form of a definition of the acicular mode of transformation as: The successive, abrupt formation of flat plates of supersaturated ferrite along certain crystallographic planes of the austenite grains; this supersaturated ferrite begins at once to reject carbide particles, (not lamellae), at a rate depending upon temperature. In effect, this is the acicular mode of transformation, even though the temperature be such as to limit the actual life of the quasi-martensite to millionths of a second. The investigation of isothermal decomposition of austenite in certain alloy steels (notably those containing chromium or molybdenum) has revealed that there may be a range of temperatures between the pearlite and bainite reactions in which the austenite decomposes at a relatively low rate.3-6 Further, it is characteristic that in the second region of fast reaction the decomposition of the austenite is incomplete by one reaction but goes to completion by a second reaction. These observations led Wever7 to a description of the bainite reaction as follows: I. The reaction takes place by initial precipitation of a martensitic intermediate structure. 2. In the upper temperature range this structure readily decomposes into ferrite and cementite. In the lower range carbon separates in an unknown form. 3. In the upper temperature range the precipitated carbide nucleates the precipitation

Jan 1, 1944

By E. Bonates

Truck/shovel systems are a major form of materials handling in open-pit mines in spite of the high associated capital and operating costs. Mine management is usually faced with a decision to purchase new equipment in order to support the steadily increasing on production. These decisions involve a high degree of uncertainty with respect to future demands and technical developments. This paper describes a computer simulation model for evaluating the optimum equipment fleet in an open-pit mining operation. The system is based on a stochastic simulation program which accounts for the various mining and economic parameters. It calculates the type of equipment and the optimal number of trucks needed to meet the production targets. Two types of selection criteria: maximum rate of production or minimum cost can be applied.

Jan 1, 1989

By G. L. Schroeder

Investigations were conducted at two underground locations, foreman's room and 5702 area, of the Kermac Nuclear Fuels Corp. uranium mining installation, Ambrosia Lake, New Mexico. The rock environment is stratified sandstone. Pressures were varied from minus 0.4 an Hg to plus 3.8 cm Hg with respect to barometric pressure, and were maintained for periods ranging from several hours to 21 days. One cm Hg overpressure (-1.5% of normal barometric pressure) produced a 20-fold decrease in Rn flux into the foreman's room as compared to the Rn flux observed during dilution ventilation. The 5702 area experienced a 5-fold decrease in Rn flux for a similar overpressure. During 21 days of continuous 1 cm Hg overpressure in the 5702 area this reduced Rn flux was maintained. The smaller reduction in flux for the 5702 area results in part from the proximity of the foreman's room to a non-pressured area and the presence of an impermeable shale lens overlying the ceiling of the 5702 area. A 0.4 cm Hg underpressure of the 5702 area increased the Rn flux into the area by 3-fold over the non-pressured value. A barometric pressure influence on Rn flux into the mine and on air Rn concentrations in non-pressurd areas of the mine was measured. A falling barometric pressure causes an increase in the flux of interstitial gas into the mine; a rising barometric pressure decreases this flux. These effects are not seen in overpressured mine areas. Radon concentrations in rock interstices show, during overpressure, decreases of all locations monitored except in the immediate vicinity of the shale lens above the 5702 area ceiling. These reductions are the result of air flowing from the mine into the rock interstices under the influence of the pressure gradient induced by the overpressure. The relative humidity of the 5702 area was reduced after 2 days of 1 cm Hg overpressure from a pre-overpressure value of 96% to 81%. The control of harmful or noisesome gases which emanate into underground mining areas from surrounding rocks is often a costly necessity. In uranium (U) mines this problem is presented by the high interstitial concentrations of radon-222 (Rn), a radioactive noble gas of 3.82-day half-period, formed in the decay scheme of U238, and the relative ease with which this noble gas diffuses from its parent rock into the interstices of the rock and then to a working area. Long-term exposure to moderate concentrations of Rn (3000 µµc per 1) and its short-lived alpha-ray emitting daughter products, RaA (Po218) and RaC (po214), has been found to result in an increased incidence of bronchial carcinomaa2 The acceptable limit of Rn daughter products in a mine atmosphere is presently set at a concentration of short-lived radon daughters which would be in equilibrium with 100 ppc of Rn per 1 of air. Ventilation of mines is conventionally accomplished by continuously diluting the mine air with fresh air brought in by fan or natural convection from above ground surface. The diluted air is allowed to vent freely to the atmosphere. This process does nothing to retard the rate at which gases (including Rn) diffuse into the mine from surrounding rock. It merely reduces the concentrations of these gases within the mine. It is suggested that in a sufficiently permeable rock environment a slight pressurization of the mine air may induce air flow from the mine into the interstices of rock surrounding the mine. The convective flow of comparatively fresh air will reduce the concentration and the concentration gradient of undesirable gases in the rock interstices adjacent to the mine. Radon will diffuse counter-current to this convective flow at a rate proportional to its concentration gradient. In time, a steady state of convection and counter diffusion will be established. The Rn flux into the mine will never be reduced to zero, and will only asymptotically approach zero as the overpressure (and hence the convective velocity of purging air) approaches infinity. During 1963 and 1964, an investigation into the effect which such applied pressures have upon the Rn characteristics of a mine atmosphere was conducted at the Kermac Nuclear Fuels Corp. uranium mines, Ambrosia Lake (near Grants), New Mexico.

Jan 1, 1967

By Gerald Verbeek, David Tara

"When selecting an impact hammer to drive a particular pile, the decision is often based on local experience. In those cases, the contractor falls back on previous experience or draws on the experience of the hammer manufacturer to select the hammer that will be able to do the job. Obviously, a more scientific approach would be to perform a pile driving simulation using one of several commercially available software packages (e.g., GRLWEAP, AllWavePDP or PDPWave).However, this type of analysis requires quite a bit more effort. First, an accurate model of the pile driving process has to be developed, which includes a model of the soil profile at the job site and input into the analysis program. Then, the model must be analyzed to assess whether the combination of hammer, pile and soil model work.Over the years, numerous individuals and organizations have tried to develop something that would fit nicely in between these approaches: something more advanced than a gut feeling yet something that could be done on the back of an envelope; in other words, a “Goldilocks” approach — not too simple, not too complex, but just right.Screening Tool CriteriaThe goals of the approach are twofold: (1) select the appropriate impact hammer to drive an open toe steel pipe or H-pile, and (2) then use the model for the subsequent high strain dynamic testing (HSDT). The Goldilocks approach centers around five different criteria.1. Maximum Driving StressTo minimize the risk of damage, the maximum driving stresses are generally limited to 80 to 90% of the yield stress (fy) of the steel section. This approach does not consider issues such as hammer alignment, initial imperfections, denting and/or elastic buckling, and pile material fatigue history. However, even when these issues are not applicable, limiting average stresses to 0.9fy or even 0.8fy does not necessarily mitigate the risk of pile damage (Mostafa, 2011)."

Jan 1, 2017

By K. V. Lindell

Introduction This paper describes a recent innovation in the design and construction of mine headframes. A reinforced concrete headframe was built by using sliding forms. A concrete headframe of conventional design was originally considered, but investigation of this project showed that it was doubtful if the bearing strength of the soil was sufficient to support the great weight of a structure of this type. In addition, the slope and the fractured condition of the serpentine bed-rock did not permit satisfactory piling. A conventional steel headframe with storage bins was then designed, but, due to the steel situation, delivery promises were set back many months. The concrete headframe was again investigated, and a design was adopted incorporating a circular headframe lower in height than that first considered, with skips discharging into a smaller surge bin. The upper section of the shaft collar was strengthened to result in a stable structure which would be supported by bed-rock, as well as by the concrete and steel lining of the shaft itself.

Jan 1, 1948

By W. W. Norton

The gradually increasing proportion of sulphide ores which lead smelters of to-day are called upon to handle has caused the roasting problem to become one of ever greater importance. Mines have increased in depth, methods of concentration have improved, competition in the purchase of ores has become more keen and it has been clear that new and modern methods of eliminating sulphur must receive a large share of attention. We may look back a score of years or so and recall the old hand roasters, some of which turned out a finely divided roasted product, and others fashioned with a "fuse-box" wherein the roasted ore was slagged. Then came mechanical furnaces of several types, the Bruckner cylinder, the Brown-O'Harra, the Ropp, and others, all designed to cut out the cumbersome hand labor of the old reverberatories. Roasting costs were thereupon reduced and tonnages stimulated to a gratifying extent. However, it seems to have been early recognized that this very feature of a greater amount of roasted sulphide ore as compared with oxide ore brought with it a train of difficulties at the blast furnaces. The mechanically roasted ore was fine physically, the blast furnaces were choked and the troubles of the smelterman were not at an end. Then the Huntington-Heberlein pot system of roasting appeared upon the scene, and later on the Dwight-Lloyd machines were invented, and inasmuch as both of these processes were designed not only to roast the ore but to agglomerate it as well, it was apparent that distinct steps in advance had been achieved. At the Murray plant, modern up-to-date roasting practice is fully exemplified and there are now in successful operation roasting furnaces or devices of several sorts: namely, Godfrey revolving-hearth furnaces, Wedge multiple-hearth mechanical roasters, Dwight-Lloyd sintering machines, and Huntington-Heberlein pots. Godfrey and Wedge furnaces will properly handle material high in sulphur, say ores with 25, 30, and 35 per cent. of that element; D. & L. machines and H. & H. pots will positively not treat efficiently ores or mixtures containing anywhere near the sulphur content mentioned, but are confined to charges containing in the neighborhood of 15 or 18 per cent. In passing, it may also be explained that, so far as the knowledge of the writer goes, Godfrey and Wedge furnaces do not economically eliminate sulphur to an extent

Jan 1, 1915

By Arthur Forsyth

A SEARCH through the available literature shows that the cobalt-nickel-silicon system has not been systematically studied. This seems rather odd because all three elements are fairly abundant and have better than average corrosion resistance; however, they have high melting points, which makes experimental work difficult. Cobalt and nickel form a continuous series of solid solutions and each metal dissolves about 7.5 per cent silicon. Many ternary alloys have been studied and the results have been published in a great many different ways, but to present such data in a short but clear and understandable manner is still a problem. The following pages describe the results of the study of 76 alloys from which the partial ternary diagram (Fig. 1) of the cobalt-nickel-silicon system has been drawn. The alloys were chosen according to the plan in Fig. la by taking definite ratios of cobalt and nickel, such as 70 Ni, 30 Co or 40 Ni, 60 Co, and adding silicon in various percentages. Each section was studied in detail by means of thermal analysis and microscopic examination, but only two of these detailed sections were thought necessary in the point perspective drawing to give a comprehensive picture of the liquidus, solidus and solid transformations that take place over the temperature ranges studied. Complete thermal analyses and microscopic data are given in Table 1.

Jan 1, 1940