Search Documents

By Peter Fischer

A demonstration plant for QSL technology with a continuous through-put of up to 10 t/h concentrate has been in operation at the Berzelius smelter, Duisburg, Germany since early 1981. In the QSL-process, both oxidation and reduction steps are performed in a single horizontal long cylindrical reactor. In the present demo-reacior, 2.5 M diameter by 22 M long, these steps are separated by a low partition wall with an underflow opening, to prevent backmixing of slag. -Tests on a variety of concentrates, including high-lead Missouri-type material and lower grades, have shown recoveries and consumables indicating very attractive economics. Investment cost estimates further enhance the economic attractiveness. Environmental protection afforded by the QSL system is a major advantage. The process has proven its reliability and versatility and is now ready for commercialization. Continued test work, including smelting secondary lead materials, is planned.

Jan 1, 1983

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By Robert M. Becker

Particle mixtures were sampled in the laboratory, using ordinary sampling procedures, to determine whether or not the compound-multinomial probability distribution and other developments of part 2 agreed with experimental results. The objective was accomplished by the Bureau of Mines by comparing the moments and moment relationships of the appropriate probability models with their corresponding experimental values over a fairly wide range. The overall agreement between the corresponding theoretical and experimental values is both good and complete. The results demonstrate that sampling to a constant amount, such as weight, of items per sample is not the same, in general, as sampling to some constant number of items per sample. The results seem to confirm all the developments of part 2 and the application of the compound-multinomial function to bulk sampling.

Jan 1, 1965

By Kurt F. Weitz

"The number of materials that can be classified as fillers covers an extremely wide range: this paper outlines those fillers of the industrial mineral type that find extensive application in the paint and plastics industriesIn the paint industry, mineral fillers are known as extender pigments. Extenders are added to paint and plastic compositions to (1) lower the cost and (2) rein-force or modify the physical properties of a composition.Commonly used extenders are classified according to chemical type and discussed in terms of the change in physical properties that they impart to a paint or plastic film. Available cost reductions and data on the consumption of extenders in the Canadian paint industry are also included."

Jan 1, 1970

By H. H. Kellogg, T. R. Ingraham

Three anhydrous zinc sulfates have been identified. They are: ZnSO,(a), stable below 1007°K; ZnS04(/3), stable above 1007OK; and ZnO.ZZnSO,. The decomposition pressure of each sulfate has been measured and the following relations calculated from the results: The measured data have been combined with the known themzodynamic properties of ZnS, ZnO, Zn, SO,, and SO, to yield univariant and bivariant phase diagrams for the system Zn-S-0. The application of these diagrams to problems of roasting zinc concentrates is discussed. PRESENT knowledge of the equilibrium chemistry of the system Zn-S:O, so essential to scientific control of zinc-blende roasting, is deficient in several respects. A basic sulfate of zinc has been reported by many investigators, but its composition is in doubt and its thermodynamic properties have not been measured. Our scanty knowledge of the properties of the normal sulfate at roasting temperatures is based on old and inexact studies. A crystal transformation in the normal sulfate, involving a sizable heat effect, has been noted by several investigators but has never been quantified. The studies reported herein were designed to fill these gaps in knowledge and to make possible a reasonably complete thermodynamic description of the system Zn-S-0 at roasting temperatures. The results make possible a far more exact understanding of zinc roasting chemistry than was hitherto possible. EXPERIMENTAL The principal experimental technique employed was the measurement of the total gas pressure developed from decomposition of either ZnSO, or ZnO2ZnS0, in a closed system. The apparatus employed was essentially the same as that described by Warner and lngrahaml and Flengas and tngraham.' The unusual feature is a flexible Pyrex bellows used to separate the reaction gas mixture (S03, SOz, and 02) from the mercury in the manometer and thus prevent corrosion of the mercury by SO3. The bellows operates without evidence of hysteresis and, barring accidents, may be used for several months. The response of the bellows varies from manometer to manometer, but is generally of the order of 0.6-cm displacement for a l-cm change in pressure. The response for all manometers has been linear over the range 0 to 1 atm. To prevent condensation and polymerization of sulfur trioxide, the bellows-manometer was maintained at 100.0" * 0.5" by a circulating bath of silicone oil. The connecting tubing between the manometer and the furnace was maintained at 100.0" * 0.2"* also, with a stirred air bath. The open end of the manometer was connected with a chamber which was maintained at a known pressure. The pressure could be varied so that readings of the height of the mercury column, measured with a cathetometer, could be made with both rising and falling mercury column. By using the average of the readings, any error due to sticking of the mercury column was minimized. The sample was placed in a 2-in.-long platinum boat formed into the shape of a half-cylinder. The sample was prepared as a fine powder and pressed against the inner wall of the platinum boat. A silica thermocouple well, covered with a platinum sleeve, was placed lengthwise along the center of the boat. The temperature of the sample was read on a calibrated Pt-10 pct Rh theirnocouple. The temperature profile of the furnace was constant within ± 0.2 C over the length of furnace occupied by the sample. The horizontal furnace used to contain the sample and the quartz reaction tube was electrically heated, with the control thermocouple placed 1/4 in. from the windings. A Brown Pyro-O-Vane temperature controller with a 3-sec response time was used to maintain the furnace temperature. Before beginning a run, the apparatus, including the bellows manometer, was thoroughly washed in sib with acid and distilled water to remove any

Jan 1, 1963

By T Casten

Freeport IndonesiaÆs DOZ (Deep Ore Zone) mine is scheduled to commence production in the second half of 2000. The DOZ will produce 25 000 tpd using mechanised block cave mining methods and will have a number of major improvements when compared to previous block cave mines in the district. The DOZ will have an independent and improved ventilation system, a flexible and efficient truck haulage system, and a more reliable crushing and conveying system than in previous underground mines in the district. This paper will describe the mine plan, haulage, and ventilation systems, and compare them to those used in other operations in the district.

Jan 1, 2000

By Enrique Munaretti, Cathy Aimone-Martin, Vitor Rosenhaim, Jair Koppe

Production blasts at one of Copelmi’s coal mine operations will be carried out 100 m (330 ft) from a neighborhood located in the town of Butiá, southern Brazil. Mine management is concerned about the possibility of damages and complaints due to blasting operations at close distances to structures of substandard construction. Blasting in the area is characterized by the use of very low powder factor resulting in confined shots in which movement is restricted to a point of almost undershooting the rock. Over the past year, tests were conducted mainly in the overburden area to determine the best approach to be implemented when blasts move closer to the town. Mine management wants vibration levels to be reduced lower than the damage limits proposed by Brazilian regulations to ensure a safety margin and mitigate perception by the community hoping to reduce the number of complaints.

Jan 1, 2013

By J. W. Bawden, J. Nantel

"The mine operator has two prime objectives when he operates a mine: (l) the mine must be safe, and (2) the mine must operate with the lowest possible costs. The operator constantly faces a dilemma; if he is over cautious with regard to safety, his costs may be very high, and if he is over-zealous in trying to reduce costs, the safety of his operation may be jeopardized.Modern bulk mining methods rely heavily on high productivity non-entry stoping techniques (e.g. open stoping, VCR, etc.). Such techniques have the advantage of removing the operator from the active and sometimes dangerous mining face and ofminimizing costly development. On the other hand, this generally results in a certain loss of flexibility in following irregular ore-waste contacts. If stopes are opened too large and/or are inadequately supported, severe dilution with resulting escalating costs usually results. If initial access drift support is inadequate for latter mine induced stresses high rehabilitation costs may also be incurred.Optimization of stope dimensions should logically occur as part of a general mine rock engineering program, within the over-all mine planning context. The same program should help highlight those areas where drift rehabilitation may be a problem.Whenever successful mining is performed, rock engineering is being applied, either by design or by chance. The cost implications of planned practical rock engineering as an integral part of mine planning and design can be very significant to the ultimate mining ""bottom line"". At Noranda Minerals Inc. allowable stope dimensions are derived using a combination of numerical stress analysis and empirical design techniques. This paper discusses the use of the above techniques and their limitations as tools for rock mechanics based stope dimension optimization. The potential cost implications of such design efforts within the general mine planning context are also addressed."

Jan 1, 1989

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2018

By J. F. Burr, D. Snyder, W. Calder

This paper provides a determination of the equivalent level of protection of the international standards relative to similar criteria used by the U.S. Mine Safety and Health Administration (MSHA) to approve two-fault intrinsically safe (IS) stand-alone equipment. U.S. mining law requires such a determination for MSHA to use alternatives to existing standards. The primary issue is to demonstrate that the international standards for equipment evaluation will provide at least the same level of protection for miners as the document currently used by MSHA.

Jan 1, 2017

By C. A. Stickels

In a recent paper, Held1 showed that rolling conditions can have a marked effect on the volume fraction of surface texture produced in low-carbon steel. This variation in rolling texture is reflected in the recrys-tallization texture and affects the plastic properties of the annealed sheet. The fact that roll friction can influence the surface deformation texture in iron and steel has been known for some time;'= but the magnitude of the effect has never been shown quite so clearly before. The analogous effect during wire drawing has been recognized for many year.4 Dillamore and Roberts5 examined surface textures in warm- and cold-rolled aluminum and copper. They found that when a surface texture was present it could be described as the interior texture rotated about the transverse sheet direction. The angle of rotation was a function of the type of lubrication, the amount of reduction per pass, and the temperature of rolling. The purpose of the present note is to show that surface textures in cold-rolled iron can also be described as interior textures rotated about the transverse sheet direction. Vacuum-melted electrolytic iron* was straight- rolled 90 pct at room temperature in a two-high rolling mill with 5-in.-diam rolls. Two rolling procedures were used: a) no lubrication with reductions of about 0.035 in. per pass, and b) heavy lubrication with lano-line and reductions of about 0.002 in. per pass. The final sheet thickness was 0.030 in. (110) pole figures were determined by transmission through specimens taken from the sheet surface and sheet midplane. The surface texture of the sheet cold-rolled according to procedure a is shown in Fig. l.* The shapes of the low-intensity contour lines indicate that the texture can be described as a partial fiber texture with a (110) fiber axis normal to the sheet. The approximate range of orientstions present is (011)[211] — (0ll)[100] — (011)[211]. This range of orientations is what one would obtain by rotating the interior texture 90 deg about the transverse sheet direction. The intensity of (110) and (222) reflections from planes parallel to the surface was measured after removing metal from the surface by chemical polishing. The surface texture here was confined to the outer

Jan 1, 1968

By H. A. Taylor

Bismuth, one of the heavier chemical elements, is a pinkish metalloid that is chemically related to antimony. It is a byproduct of lead and tungsten extraction and, to a lesser extent, of copper and tin extraction. Antimony is a metalloid and less heavy chemical element, an extraction coproduct of metals such as lead, silver and gold. While both bismuth and antimony are metalloids, their major uses are as chemical compounds. The most frequently updated resources that always cover bismuth and antimony are the Bismuth Advocate News (BAN) and link at www.basicsmines/bismuth and the frequently updated Basics Mines Update blog at http://basicsmines-update.blogspot.com. The Bismuth wiki on Wikipedia also can be very helpful.

Jan 1, 2010

By K. N. Subramanian

Previously reported work on total oxidative leaching of chalcopyrite concentrates ha s shown that high copper extractions are obtained at 210°C and 0.4 MPa oxygen pressure. A simple integrated flow sheet using pressure leaching, solution treatment involving precipitation with a calcium base, and electrowinning to produce wire-bar-quality copper is described. Reagent and energy requirements developed from this work indicate that the process could be attractive for small operations where a smelting-refining complex cannot be justified.

Jan 1, 1978

By L. J. Han, Y. J. Zong, S. Y. Wen, J. J. Wei

"Stress strain curves characteristics, deformation and strength properties, and failure process and characteristics of sandstone samples under different stress states were analyzed through triaxial compression tests carried on using TAW-2000 microcomputer control electro-hydraulic servo rock triaxial test system. The experimental results reveal that peak strength, residual strength, elasticity modulus and deformation modulus increase linearly with confining pressure, and failure models transform from fragile failure under low confining pressure to ductility failure under high confining pressure. Macroscopic failure forms of samples under uniaxial compression was split failure paralleling to the axis of samples, while macroscopic failure forms under uniaxial compression was shear failure, the shear failure angle of which decreased linearly with confining pressure. There were significant volume dilatation properties in the loading process of sandstone under different confining pressure, and then based on acoustic emission damage and volumetric dilatation damage the damage evolution properties of samples were analyzed, and damage constitutive model were established, realizing the real-time quantitative evaluation of samples damage state in loading process. INTRODUCTIONDamage is a phenomenon that micro defects in material under monotonic loading or reloading will lead to progressive decrease of the cohesion and damage of volume units. Many scholars at home and abroad have carried out systematic researchers on damage evolution characteristics and constitutive model of rock, and have achieved a series of remarkable results in this field. Lu Y.D. (2004) studied the complete stress-strain curve’s characteristics of marble under triaxial compression, and established the bilinear elastic-linear strain softening-residual ideal plastic damage constitutive model. Ren J.X. (2001) studied the damage evolution laws of coal and rock mass by computerized tomography triaxial loading system, realizing the quantitative evaluation of damage state. Zhang Z.L. (2011) studied the deformation and failure mechanism of strong weathered sandstone by triaxial compression test, and analyzed the damage evolution processes and established the damage evolution equations based on the density method. Li X.J. (2012) studied the microscopic damage characteristics of siltstone under triaxial compression by scanning electron microscope and digital image technology, and analyzed the statistical distribution characteristics of cracks azimuth angle, length, width. Zhou J.W. (2012) studied the strength, deformation and fracture damage characteristics of sandstone by uniaxial cyclic loading and unloading tests, and defined damage variable based on linear damage mechanics theory and acoustic emission (AE). Cao W.G. (2006) established a new damage model and a statistical damage constitutive model of rock under specific confining pressure according to the force of damaged part and undamaged part in rock on the base of statistical damage theory. Li S.C. (2014) studied the damage evolution characteristics in the whole uniaxial compression process of sandstone by electrical resistivity and AE, and proposed a status qualitative criterion for rock damage."

Jan 1, 2015

By W. A. Kracht

The McGill Bubble Size Analyzer, with the original image-capturing device (digital video camera), has a proven record for measuring bubble size distributions that are relatively narrow, such as in mechanical cells with frother. However, some problems arise when dealing with bubble size distributions characterized by a bi-modal shape and wide range of sizes such as found in some flotation columns. To measure wide bubble size distributions it is necessary to increase both the resolution to image the small bubbles and the viewing area to include the large bubbles. This can be done using a digital still camera: digital still cameras can have higher resolution than the digital video cameras currently used and with the proper lens the viewing area may be increased without resolution loss. The digital still camera approach was used to measure bubble size distributions in flotation columns at different operations in Chile. A comparison with typical bubble size distributions generated with mechanical cells is presented.

Jan 1, 2007

By Rollie E. Dutton, David A. Stubbs

"A sensor has been developed and tested that is capable of emitting and receiving ultrasonic energy at temperatures exceeding 900°C and pressures above 150 MPa. The sensor works with standard ultrasonic pulser-receivers and has demonstrated the capability of measuring workpiece deformation during hot isostatic pressing (HIP). Details of the sensor design, performance, and coupling of the ultrasound to the workpiece are described. Ultrasonic data acquired by the sensor, in situ, during HIP runs and at elevated temperatures in air are presented.INTRODUCTIONHigh temperature structural components, such as structural castings for jet engines, nickel-base superalloy turbine blades, and ceramic and metal matrix composites made from powders are often densified by hot isostatic pressing (HIP). For powder consolidification, the HIP process involves sealing the powder (and reinforcing fibers for composites) within an evacuated ""Can"" made of a material that softens at high temperatures. A hydrostatic pressure is then applied by pressurizing the inside of the HIP vessel with argon gas (up to 140 MPa). The hydrostatic pressure densities the powder through the elimination of the porosity between the powder particles.This paper presents details of the development and preliminary testing of an ultrasonic displacement sensor that can be used to monitor materials processing, in situ, at temperatures and pressures significantly higher than current ultrasonic displacement sensors. The target processing environment for this sensor is that typically found in a hot isostatic pressure (HIP) vessel, i.e., temperatures exceeding 1000°C and pressures above 138 MP a."

Jan 1, 1997

By C. A. Morais, L. V. Resende

"The technological development observed in recent years has stimulated the application of rare earth (RE) elements. Amongst their various applications it is well worth mentioning their use in electronics, superconductors, nuclear medicine, as well as in special inks - as those used in radar invisible airplanes. TV and computer monitor screens present as coating a powder containing some rare earth elements, mainly Europium and Yttrium. The recovery of the RE elements from electronic scrap is extremely important as the economic and environmental issues are concerned. This paper describes the study of the Eu and Y recovery from e-scraps. The first step of the process was the leaching of the powder obtained by manually scraping the inside surface of the screen. After the optimization of the leaching, the dissolution of Eu and Y was higher than 98 w/t% and a pregnant sulfuric liquor containing 11.9 g L-1 Y and 0.72 g L-1 Eu was obtained. The second step was the separation of the metals found in the liquor by the solvent extraction technique. The separation of Eu and Y was carried out in a counter current circuit compound of 3 extraction stages, 7 scrubbing stages and 15 stripping stages. DEHPA was used as the extractant, whereas a diluted sulfuric acid solution was applied as scrubbing agent and a hydrochloric acid solution at high concentration was used as the stripping agent.INTRODUCTIONThe rare earths (RE) are a moderately abundant group of 17 elements composed of lanthanides, scandium and yttrium. Amongst the RE, promethium (Pm) is extremely rare, however several of the RE elements are not very rare and occur dispersed in a variety of forms (Greenwood & Earnshaw, 1984; Tyler, 2004).The innumerable applications of the RE elements are based on their particular properties, mainly their spectroscopic and magnetic properties (Martins & Isolani, 2005). The technological development observed in recent years has stimulated the application of rare earth (RE) elements. They have been used in agriculture, electronics, superconductors, nuclear medicine, automobile industry, special inks – as those used in radar invisible airplanes, X-ray screens, high intensity mercury vapour light bulbs, neutron scintilators, charged-particle detectors and optical memory reading systems (Maestro & Huguenin, 1995; Nagaosa & Binghua, 1997; Sánchez et al., 1999)."

Jan 1, 2012

By E. Siami-Irdemoosa, S. R. Dindarloo

"Discrete event simulation is a stochastic mathematical modeling tool with applications in queuing systems. Many mining operations, both surface and underground, can be simulated in the context of queuing theory , for example open pit loading and haulage operation, underground level and vertical transportation, and mineral processing circuits. A computer simulation model of the operation is an invaluable tool to study both the system’s dynamics and conducting sensitivity analysis on different effective elements on system performance. In this paper, merits of discrete event simulation in decision making in mining engineering is discussed. Moreover, a stochastic simulation framework for selection and sizing of shovels and dump trucks in surface mining is presented to elaborate one example for applicability of the method in mining operations. INTRODUCTION Mathematical modeling is a valuable tool in design, optimization, and decision making in both surface and underground mining operations. Several researchers have tried to study different aspects of mining operations using a wide range of mathematical techniques such as linear programming[1], analytical hierarchy process [2], non-linear programming[3], genetic algorithms[4-5] ,mixed integer programming [6], machine repair model[7], queuing theory [8], and conventional spreadsheet calculations based on experience and engineering judgments. There are different uncertainties in typical mining operations (e.g. material loading and haulage, drilling, and blasting). For example, in a truck-shovel operation, different governing activities such as loading, haulage, and dumping cycles are stochastic variables. Moreover, analytical modeling of a large truck-shovel operation is very complicated. Thus, application of analytical and/or deterministic techniques cannot guarantee a solution for different problems that are encountered in daily mining operations. Discrete-event system simulation (DES) is a modeling method for such time discrete and probabilistic phenomena [9]. DES has been employed by different researchers in mining engineering through available software and languages such as GPSS, SIMAN- ARENA, and SLAM [10-14]. Most of the studies so far, tried to evaluate some “what-if” scenarios, to understand the possible effects of changing different input variables on overall mine economics. For instance, Baffi and Ataeepur (1996) used Arena to simulate a truck-shovel operation [10]. Also, Sturgul has conducted extensive studies in the application of DES in the mining engineering field [15- 17]. A very good background review of application of this technique in the industry can be found in [15-16]. Previous studies have shown that, different approaches including deterministic, stochastic, and experimental methodologies result in considerable differences in outputs [18]. These techniques lead to different solutions, regardless of the quality of technique/software itself or knowledge of the modeling team. Hence, the first step is to develop a comprehensive simulation framework to obtain nearly the same optimal results for the same input variables, regardless of the employed technique."

Jan 1, 2016

By Bobby G. Cahoon

The ( ) Tayaaja ( ) . The deposit ( ) 130 kilometers due east of the continental divide and approximately 290 kilometers east-southeast of Lima (Figure 1). Relief in the immediate vicinity of the mine, which lies or the west side of the Mantaro river, is in excess of 2,000 meters, and the elevation varies from a low of 2,000 meters above sea level on the Mantaro River to a high of 4,386 meters at point T-27 (Figure 2). Although the Cobriza deposit was first reported by the Italian Geographer Antonio Raimondi in 1866, only three reports have been published on the deposit, which began production in 1966 (Duefias, 1908; Fernandez Concha and Garcia y Garcia, 1961; Petersen. 1965). Many private reports have, however, been written by geologists employed by the Cerro de Pasco Corporation. These reports and the author's observations, while employed as the Cobriza Division Mine Geologists form the basis of the present paper, which describes the relations between-the ore controls in the Cobriza mine and the regional and local structure.

Jan 1, 1971

By Deirdre Bradshaw, Cornelius Vos

"The detailed understanding of the variability in process performance parameters within an ore body forms a key aspect of ensuring that proper decisions are made with regards to the economic viability of that ore body. To gain this understanding, various tools have been developed over the years, of which the batch flotation test is the most well-known and applied technique for investigating the flotation separation of ores. In this paper, the Julius Kruttschnitt Mineral Separability Indicator (JKMSI) is put forward as a small-scale test, suitable for the characterization of the flotation separability of copper porphyry ores. It is demonstrated that the JKMSI can be a complementary technique to the batch flotation test, with the capability to further improve the knowledge of ore body variability. The response from this test has been shown to be sensitive to particle size and modal mineralogy, providing a critical link between flotation and upstream comminution activities. The trade-off between the fineness of grind and the recovery target can thus be evaluated to determine the minimum energy application required for optimal separation economics. The test is designed to utilize small sample quantities of various sizes, providing an opportunity to increase our understanding of ore variability through increased tests. This complements our ore body knowledge and combining this with efforts in comminution (Powell, 2013) provides a platform for extending the concept of flexible circuit design."

Jan 1, 2014