Search Documents

The man in the street (and no doubt most members of the Institute) thinks of wire, if he gives it any thought at all, as a most commonplace commodity. It is an accepted necessity, and like most necessities is taken for granted, unless a shortage in one or other of its multitudinous forms or products causes inconvenience.For many years Australia has ·been a large consumer of wire, particularly for fencing. With the rapid development of secondary industry the demand has increased in both size and character until at the present time much of the wire produced in this country is used as raw material for subsequent manufacturing processes. The call has been of so varied a nature that the Newcastle Wire Mills now turn out a greater variety of wire types than any other single plant in the world.In this paper, the aim is to provide a picture of the manufacturing, properties, and uses of wire. No attempt is made to cover the subject in any detail, as the field is much too broad for anything other than general treatment. Many phases, particularly in regard to manufacturing processes, are, therefore, dealt with cursorily, but it is hoped that the paper will, without delving too deeply into the technical aspects of Wire production, give a general appreciation of:- (a) How steel wire is made. (b) The remarkable physical characteristics obtained by judicious combination of chemical composition, heat treatment, and subsequent cold work. (c) The uses of steel wire.HISTORY.Best known of the early references to wire is that appearing in Exodus, where mention is made of gold wire being used for the sacerdotal robes of Aaron. However, the period in question, about B.O. 1491, is comparatively modern history as far as wire is concerned, for specimens believed to have been made about B.O. 4600 have been found. It is fairly certain that the Egyptians produced iron wire in B.O. 4000. Of particular interest is the

Jan 1, 1947

By E. Wittenau

This paper describing the concentrator practice of the Copper Queen Branch of the Phelps Dodge Corporation at Bisbee, Ariz., is one of a series of papers on milling methods and costs being prepared by the United States Bureau of Mines. The Copper Queen Concentrator treats 4,000 tons of copper ore daily by preferential flotation, whereby the copper sulphides are floated and considerable iron pyrite is depressed. During 1929 the heads to the concentrator averaged 2.15 per pent of copper, the recovery was 91.32 per cent of the total copper, and the concentrates produced contained 12.92 per cent of copper.

Jan 1, 1931

By Shaohua Ju, Feng Jiang, Chuanhua Li, Jinhui Peng, Libo Zhang

A T-junction microchannel is proposed to overcome the existing problems in conventional solvent extraction of indium from zinc hydrometallurgical process. Experiments were performed to separate In3+, Fe3+ and Zn2+ from sulfate solutions using Di-(2-ethylhexyl)phosphoric acid (D2EHPA) as the extractant. The effect of parameters such as pH, microchannel size and contact time on the extraction behavior of In3+, Fe3+ and Zn2+ was investigated. At contact time of 2.52 s and initial solution pH of 0.48, the extraction efficiency of In3+, Fe3+ and Zn2+ was 99.13%, 8.31% and 2.45%, respectively and separation factor of In3+/Fe3+ and In3+/Zn2+ were almost 1229.54 and 4864.98, respectively. Then, the loaded organic phase was stripped in T-junction microchannel. At contact time of 33.6 s, 99.64% of stripping efficiency of In3+ and stripping equilibrium were reached, while concentration of Fe3+ and Zn2+ was lower than 0.01 g/L with good separation of In3+ from Fe3+ and Zn2+.

Jan 1, 2016

By Michael J. Friedel

The integrity of mine structures, such as the roofs, ribs, face and supporting pillars, is difficult to assess beyond the exposed surface. To mitigate potential rockfall hazards, the U.S. Bureau of Mines is assessing the usefulness of Rayleigh wave dispersion analysis to detect damage and stress-relieved zones in mine structures. Classical surface wave dispersion modeling is utilized at both laboratory and field scales in damaged and undamaged material to assess the integrity of a mine pillar and roof. To more fully exploit Rayleigh wave propagation characteristics, derivation of a novel dispersion parameter was conducted using a convolutional model. The development of a suitable Rayleigh wave dispersion system based on insight derived from forward modeling is presented. The application of inverse modeling for damage and stress assessment in the mine environment is also discussed.

Jan 1, 2010

By R. W. Culley

"In many areas of Saskatchewan, known gravel deposits have been depleted or are diminishing rapidly; in other areas, particularly in the north, demands for all-weather highways and access roads are far exceeding the supply of gravel sources with which to surface them. These two problems have made conventional methods of air-photo and ground surveys insufficient for gravel location. In the first case, hauling costs on construction now warrant searching for buried deposits and for smaller, less obvious surficial deposits that may be closer to the project. In the second case, search and access conditions are so difficult and costly that the ratio of successes to failures must be kept very high. The Department of Highways has long been aware of the oncoming scarcity of quality gravel deposits and is continually investigating ways of forestalling it. One of these ways is the use of airborne geophysical methods that permit rapid coverage of large areas and that sense and discriminate between earth properties to a significant depth below ground surface. In 1967, the Department began an investigation of an airborne conductivity survey method called INPUT*, or ""Induced Pulse Transient'', leading to a trial in 1968 and data analysis in 1969. The results of this trial initiated• modifications to the technique to improve its sensitivity for mapping shallow deposits. Part way through this modification in 1970, a decision was made to change to an airborne resistivity survey method called EPHASE*. Trials with this technique were conducted and analysed in 1971. This paper is an explanation of the E-PHASE system and a summary of the results from one of three areas mapped in 1971."

Jan 1, 1973

By W. E. Young

This study was made to present the mining methods and costs of a uranium mine typical of other mines in the highly productive Westwater Canyon member of the Morrison formation in New Mexico. Four mining methods have been used at the Section 23 mine: the retreat- room-and-pillar method, a sublevel-slicing method (also called top-slicing), the horizontal-cut-and-fill method, and a modification of the ring-drill method. The application of the methods at this mine and at other mines in the area should be of benefit to operators with similar problems. Ore bodies in the Section 23 mine are irregularly shaped and vary in size, in rock strength, in moisture content, and in uranium concentrations; different mining methods are required and mining costs are not constant. A 6-month period of operation at the Section 23 mine was analyzed and mining costs, not including amortization, depreciation, or Federal taxes, averaged about $6.80 per ton.

Jan 1, 1965

By Morley I. W

In the year 1926, Edie Creek, in the Morobe District of the Mandated Territory of New Guinea, saw the greatest gold rush of recent years. Situated 35 miles inland from the coast, and at an altitude of over 6000 feet, Edie Creek presented to the original prospectors a wet, jungle-clad uninhabited, and inhospitable region. There were no roads; and the only means of approach from the equally inhospitable coast was by an eight to ten days' tramp through coastal swamps and gorge-scarred mountains. All food supplies and equipment had to be carried on the backs of "kanakas," and in many cases through country occupied by hostile natives.Since the first discovery of payable gold at Edie Creek, mining on the Morobe Goldfield has shown remarkable progress, and in spite of the tremendous natural difficulties, the field today ranks as one of the most important in Australasia.Aeroplanes, more than any other factor, have been responsible for this rapid development. They provide the only means of transport from the coast, and at present serve the needs of over 600 Europeans and 3000 indentured native labourers engaged in the industry.

Jan 1, 1933

By J Y. C Lo

The construction of two drainage tunnels and the associated subvertical drain system at the Po Shan area in Hong Kong was completed in December 2009. This project is the first of its kind to utilise drainage tunnels and a network of subvertical drains to regulate the groundwater table to enhance the long-term stability of the hillside of Po Shan area.The groundwater levels, monitored by preinstalled piezometers, once exhibited dramatic drops during drilling of the subvertical drains; however, have recovered from natural replenishment after effectively plugging of the drains. The level of groundwater drawdown is in line with the design function of the subvertical drains. In order to understand the groundwater flow pattern in the Po Shan area during and after construction and to set out operation schemes for the subvertical drain system so as to control the groundwater table in the Po Shan area, a post-construction review has been carried out to examine the behaviour of the drainage system and its impact on the surrounding subsurface groundwater flow.This paper presents a review of the groundwater monitoring data during and after the construction of the drainage tunnel system covering a period of over 3.5 years. A simplified conceptual hydrological model is developed, which has been verified by the monitoring data, to capture the key elements with regard to groundwater variations in different stages of the construction. The performance of the tunnel and subvertical drain system as revealed from these field measurements is discussed.

Mar 8, 2011

By K. L. Williams

The Bureau of Mines tested a prototype tapered-element oscillating microbalance (TEOM) dust monitor for measuring respirable coal mine dust. The monitor uses the inertial behavior of a vibrating element to measure the mass of sampled dust. Tests were performed to determine variability, drift, the effect of humidity, placement of collection filter, and element orientation during analysis, and comparability with gravimetric measurements of respirable coal dust. Variability was about 1.6 µg. Over about 26 h at 46 pct relative humidity, drift was very slightly negative. When the relative humidity was increased to 78 pct, all units showed a total positive change less then 40 µg over about 70h. Filter placement variation on the tapered element resulting from in- consistent sizing of the filter mounting bases caused significant error (up to 0.2 mg). In practice, calibration of the system for each new filter will eliminate that error. Orientation of the element during analysis did not introduce significant error, but care is necessary when mounting the canister that houses the element to avoid damping oscillation of the element. Dust tests were performed in an aerosol chamber using coal dust. Measurements made by the TEOM dust monitor agreed to within 10 pct of simultaneous measurements by gravimetric personal samplers.

Jan 1, 1986

By S. Flewelling, M. Scobie, G. R. Baiden

"SynopsisA feasibility study to develop a research program, the Mine Automation Plan (MAP), was recently completed. This was undertaken by a team comprised of Inco Ltd., Falconbridge Limited, the Canadian Centre for Automation and Robotics in Mining (CCARM) and the Centre for Resource Studies (CRS). The study was sponsored by PRECARN Associates, which is a consortium of thirty-six Canadian companies focussed on research and development in artificial intelligence and robotics. PRECARN Associates was formed in 1987 when a number of research proposals were funded in the fields of process control systems, robotics systems and intelligent engineering systems. In July 1991, PRECARN accepted the next round of proposals for research. The MAP project was one of the successful proposals, being awarded $100,000 for the development of a feasibility study defining a long-term R&D plan for underground hardrock mining automation.The development of the feasibility study started by addressing the fundamental structure of the mining process, and its relationship to the metallurgical process, over-all infrastructure support and management systems (Fig. I).Mining may be considered as comprising five subprocesses: (I) delineation; (2) development; (3) production; (4) backfilling; and (5) infrastructure support services. Within these subprocesses many applications for artificial intelligence and robotics exist. The mining process is dependent upon the interaction between the physical mining process and information. For example, the delineation process is dependent on geomechanical, geochemical and geophysical techniques to develop a model of the orebody based upon access to such data. This same relationship between the physical and information models holds true through the development, production, backfill and infrastructure support systems.The foundation for the MAP study has been the recent development by Inco Ltd. of an underground communications system (Fig. 2). The system has the ability to supply high bandwidth communications, over voice, data and video to mobile and stationary locations within the mining operation. It is seen to be the future backbone of a comprehensive, automated information system which should permit the application of the concept of Computer Integrated Manufacturing (CIM) to underground mining. CIM, through the automated flow of information, has been successful in integrating the engineering, production and various support groups in manufacturing."

Jan 1, 1994

By J. J. Jonas, G. Gagnon

SHG zinc was extruded in the temperature range 110" to 350°C and the strain rate range 0.05 to 5 sec-1 The strain rate/flow stress/temperature results were analyzed using a power sinh stress relationship. When temperature changes due to the heat of deformation and to heat losses are neglected, the exponent of the sinh function of the stress is 5.6, and the apparent activation energy of deformation is 28 kcal per mole. When these changes are taken into account, the exponent decreases to 4.7 and the activation energy to 23 + 2 kcal per mole. The corrected stress exponent and activation energy are in very good agreement with published values obtained from creep experiments, and suggest that the hot extrusion of zinc is controlled by a mechanism involving self-diffusion. When the extrusion and creep data are compared using a Zener-Hollomon parameter and either a sinh or an exponential stress term, an appreciable offset is observed, which may be due to the difference in impurity content. For a given set of extrusion conditions the ram speed, maximum pressure, and initial temperature can also be correlated using a Zener-Hollomon parameter and a sinh pressure term. THE deformation of metals at temperatures over about one-half the absolute melting temperature has been extensively studied at creep strain rates. By contrast, relatively little work has been carried out on the behavior of metals at hot working strain rates. Most of the latter investigations have been performed using simulative methods, such as hot torsion and hot compression, in which the friction conditions and temperature rise during deformation may differ appreciably from those existing under industrial conditions. Recently, however, Wong and Jonas1 used a scaled-down industrial process to determine the stress and temperature dependence of the strain rate during the extrusion of aluminum. In such tests, the effects of friction and adiabatic heating are closer to those produced in industrial operations. Also, with regard to the testing of materials of limited ductility such as zinc, hot compression and hot torsion do not permit the attainment of true strains as large as the deformations usually applied commercially. The present study was undertaken to investigate the extrusion behavior of Special High Grade (SHG) zinc. The detailed objectives were: 1) to establish the stress and temperature dependence of the strain rate with and without a consideration of adiabatic heating, 2) to study the pressure and temperature dependence of the ram speed, and 3) to investigate the microstruc- tural changes occurring during the deformation. The last aspect of the investigation will be covered in a separate paper. The treatment described below differs from that of Wong and Jonas in that the adiabatic temperature rise during deformation is taken into account, and the calculation of the mean equivalent strain rate is based on the redundant as well as on the homogeneous work. EXPERIMENTAL PROCEDURE Rods from two shipments of continuously cast SHG zinc* were used in the investigation. The composition *Supplied by courtesy of Cominco Ltd. range of the impurities present, as given by the supplier, was: Pb: 0.0013 to 0.0023 pct, Fe: 0.001 pct max Cd: 0.0001 to 0.0006 pct, Cu: 0.0002 to 0.0005 pct, Ti: 0.0001 pct max; thus, by balance, zinc valued from 99.9963 to 99.9966 pct. The as-received rods were machined into billets having a nominal diameter of 1.56 in. and a nominal length of 1½ in.; longer billets up to 4 in. in length, were also used to investigate special aspects. The as-machined rods were annealed at 400°C for 24 hr and slowly cooled. This treatment produced a columnar grain structure, with a grain size of about $ by 2½ cm which was appreciably larger than the as-cast one. A 150-ton, direct extrusion, vertical press was used. Ram displacement and force were recorded continuously against time. A constant flow control valve permitted the maintenance of a range of preselected ram speeds up to in. per sec. The selected speed was held constant, irrespective of the required force, as long as the load developed was below the maximum available. Strain gages were used to determine the force; the gages were calibrated before and after each testing period with a 200,000-lb capacity load cell. Further details of the experimental equipment can be found in Ref. 2. The billets were preheated for 90 min in the extrusion container, which was well insulated so as to minimize temperature gradients. This period was sufficient for the billet to reach a uniform temperature at all temperatures between 110" and 350°C. A square-shoulder die having a 0.290-in. diam central hole was used. The extrusion ratio was 30 to 1. This is equivalent to a reduction in area of 96.7 pct, an elongation of 2900 pct, and a true strain of 3.4. The ram speed was varied over two orders of magnitude from 0.0027 to 0.26 in. per sec. The ram was water-cooled during most of the tests, although some experiments were conducted with a preheated, uncooled ram. All extrusions were run without lubricant, which resulted in conditions of sticking friction. EXPERIMENTAL RESULTS Stress Dependence of the Strain Rate Neglecting Adiabatic Heating. The maximum force required to extrude is given in Table 1 for each of the five initial

Jan 1, 1970

By S. W. Zoldok

[The Bull Valley iron-ore district lie,; in the northern part of Washington County, Utah, approximately 30 airline miles southwest of the highly productive Iron Springs area (fig. 1). Iron-ore occurrences in the district have been known for many years, but they have not been mined, largely because of the inaccessibility of the area. The Bureau of Mines established a development project in the Bull Valley district in September 1941. Two separate areas, the Pilot and the Cove Mountain, were investigated. The work was planned to increase iron-ore reserves for steel production in the Western United States. During the project period three diamond-drill holes aggregating 1, 000 feet were completed (fig. 2). The program also included 6 408 linear feet of surface trenching and 171 feet of underground work (figs. 2 to 8, inclusive). Analyses were made of 460 samples from the diamond-drill holes and surface and underground excavations. The results of the analyses are given in tables 1, 2, 4, and 5, and the logs of the diamond-drill holes are shown in table 3. Field. work was completed in September 1942.]

Jan 1, 1953

By Henry D. Hibbard

I. INTRODUCTION. THESE impurities are perhaps the most important things in steel-especially steel made by the oxidation processes-the effect of which has not been at least approximately determined. By oxidation processes I mean the Bessemer and Siemens-Martin, during which the metalloids in the charge are removed by oxidation. It has been truly said that it is a clear advantage to have a new name for a new thing. To secure this and to economize space, let us adopt the name sonim (plural sonims) to designate the solid non-metallic impurities existing in steel or other metal. I would define a sonim as a solid non-metallic portion of matter existing as an impurity in metal. A piece of sand, brick, clay, or such material, imbedded in metal, would be considered as a foreign body, not as an impurity, and therefore not a sonim. The studies of sonims of which the results have been published hitherto, have been made chiefly or wholly on finished or at least on cold steel, without much, if any, regard to the specific methods by which the steel was made. While many of the results so obtained are valuable, they give little help in determining the cause, effect, or cure of the disease. It is not enough, in such a study, to know merely the commercial name of the process; for within the field of each process lies a great number of possible variations, each of which will yield a result differing in some respect from all others; and the control of sonims is particularly dependent. on the metallurgical treatment of the metal, because of the inability of analytical chemistry to throw much light on their presence, condition, and effect, as they usually occur in commercial steels. The microscope aids more, perhaps, than chemistry in their study.

Apr 1, 1911

By MacLean L

In 1975 the Commonwealth Government established import parity pricing for all liquid hydrocarbons discovered after the 16th September, 1975. These discoveries were termed "new oil" to differentiate them from existing discoveries and production. Overnight the price of the product being sought trebled, resulting in greatly enhanced economics by increasing the potential returns on existing prospects and by making smaller plays economically viable. After 18 years of drilling, the offshore Gippsland Basin has attained a moderate level of exploration for a basin of its size. Fifty seven prospects have been drilled within the basin but only a few of these were drilled along the southern and northern margins, while the deep water areas along the eastern margin have remained virtually undrilled following the Hapuku-1 oil discovery. The major hydrocarbon accumulations within the basin are trapped beneath the Latrobe Unconformity surface and exploration has largely concentrated on this single play in areas immediately adjacent to the major producing fields.

Jan 1, 1982

By W. M. Rutherford

A knowledge of the limits of miscibility between reservoir oil and possible injection fluids is required for selection of the optimum miscible-injection fluid. Limits of miscibility can be estimated from the results of equilibrium phase-behavior experiments. They can also be determined by means of displacement experiments conducted in a high-pressure sandpack. This paper describes the equipment and procedure which have been developed for determining miscibility conditions by stable displacement. A systematic series of displacements of a West Texas reservoir oil was carried out. The results indicate that, at constant pressure, miscibility is a function only of the pseudocritical temperature of the injection gas. This fact, together with improved experimental methods, makes the displacement technique a rapid, reliable means for determining miscibility conditions. In conjunction with the displacement experiments, phase diagrams were constructed for the oil with dry gas and propane and with dry gas and ethane. Phase behavior of the methane-ethane-propane system was determined at 110°F. The experimental work demonstrates the feasibility of using ethane-rich gases to reduce cost and pressure requirements for miscible displacement. INTRODUCTION In recent years, interest in the miscible displacement of oil by light hydrocarbon mixtures has been high. Many pilot and a few field scale projects have been started.1 These projects have made use of various methods for achieving miscibility: (1) the LPG-slug process, (2) the enriched-gas-drive process and (3) the high-pressure gas-drive process. Some field projects have been successful; the results of others are debatable. In general, projects which have performed best have involved the injection of an appreciable fraction of a pore volume of miscible material. Economical application of miscible displacement depends strongly on the cost of the miscible-injection fluid. If an appreciable fraction of a pore volume of material is required for successful application of these methods, a precise knowledge of the minimum requirements for miscibility in terms of composition of injection fluid is essential. Therefore, reliable experimental methods for determining miscibility conditions are important, and a procedure for estimating these conditions from the composition of the reservoir fluid is highly desirable. The subject of this paper is the problem of determining conditions which result in miscible displacement of oil by light hydrocarbon mixtures. Miscibility conditions can be estimated by means of equilibrium experiments conducted in a PVT cell, or they can be determined by means of high-pressure displacement experiments. This paper describes the equipment and procedure which have been developed for the determination of miscibility by high-pressure displacement experiments. These methods have been applied to the displacement of a West Texas reservoir oil with mixtures of dry gas, ethane and propane. In conjunction with the displacement experiments, triangular phase diagrams have been constructed for mixtures of the oil with dry gas and propane and with dry gas and ethane. The effect of injection-gas composition on conditions for miscible displacement in high-pressure sandpacks and cores has been the subject of several published papers.2-5 The experimental methods used in these investigations were such that displacements were unstable, and the effects of fingering and/or gravity layover are clearly evident in the results. Miscibility conditions were probably correct in spite of the instability phenomena, but the experiments evidently were time-consuming, and limited data were reported. Systematic high-pressure flow studies which would support a correlation of miscibility conditions have not been reported; however, Wilson5 has proposed the use of pseudocritical temperature of the injection gas as a parameter and Benham, et al,6 have based a miscibility correlation on observed and calculated equilibrium data.

By Welby Courtney

Because of the inherent safety problem associated with the deposition of airborne respirable dust onto the floor and other airway surfaces, the Bureau of Mines investigated the rate of reduction of airborne respirable dust in an airway due to deposition of the particles onto the surfaces of the airway. The effects of relative humidity and air velocity on the deposition rate were examined. It was found that the deposition rate was comparable in magnitude with the Stokes sedimentation rate and that it was independent of relative humidity. However, near the dust source the deposition rate depended significantly upon the air velocity, with such dependence decreasing with increasing distance from the dust source. In addition, the size distribution of the airborne particles was approximately constant along the first 300 ft of the airway, indicating that it was not merely the larger (heavier) particles that were being deposited. These results suggest that deposition, though comparable with the Stokes sedimentation rate in magnitude, does not follow a simple Stokes-type process, and that the process of deposition remains to be explained.

Jan 1, 1986

By M. Cross

INTRODUCTION The development of refining processes involving gas injection into liquid metals has seen the evolution of a variety of designs [I]. During the last few years or so the top, bottom and side blown processes have, essentially, been combined to produce a series of mixed gas blowing schemes (eg. the LBE [2,3] and LD-OB processes [4,5]). Although, a variety of mixed gas blowing processes have been carefully engineered and recorded operational experience now attests to their effectiveness, optimising their design and operational performance is another matter. Detailed process analysis of such operations is impeded by the complex nature of the physical and chemical processes involved: . fluid flow behaviour of the liquid metal and injected gases, . chemical reactions in the vessel, . mass and heat transfer within the fluid phases in the vessel, . influence of the geometry (eg. location of the tuyeres, etc.), . monitoring the operational performance. By and large, design and operating parameters evolve from a combination of laboratory scale experiments, pilot plant work and, of course, practical engineering experience. Conventionally, the gas-liquid system used to model the industrial process is air-water, for a number of valid reasons including – . visual demonstration plus geometric and (to some extent) dynamic similarity, . the fact that the system demonstrates, at least, qualitatively many of the complex features of gas injection - interaction between the gas and the liquid - the nature of the gas flow behaviour - qualitative indications of mass transfer rates Important experimental contributions to the understanding of gas liquid systems include the work of Brimacombe [6], Wraith [7], T.Robertson [8], D.Robertson [9], Guthrie [10] and Szekely [11] (these references provide starting points to identify the major published work in this area). Although air-water systems have been instrumental in providing a great deal of qualitative insight into the fluid flow behaviour of the processes, reliable quantitative predictions are more problematic. A number of workers (notably Brimacombe and colleagues [6, 12])have demonstrated that different gas-liquid systems can lead to wide variations in behaviour. Other limitations of physical modelling include the assumptions of isothermal flow, scale- up of turbulent flow behaviour and the inability to directly include the effects of chemical reactions. The above limitations in physical modelling, therefore, yield a natural role for mathematical modelling provided that it can be made comprehensive enough whilst remaining cost-effective. The major physical processes involved in gas injection systems may be summarised as . behaviour of the gas envelope structure in moving through the liquid metal . the global movement of the liquid metal . momentum interaction between the liquid metal and the injected gas . heat transfer and mass exchange via the chemical react ions. The behaviour of gas envelopes forming at a tuyere and then moving through the liquid has been investigated thoroughly by a large number of workers. Such models are generally based upon simple physic- al concepts derived from visual observation. An early model by Davidson and Schuler (DS), based upon a force balance between the liquid inertia and a combination of the bouyancy and momentum forces on the envelope, has proved to be a useful tool in predicting bubble volumes at detachment [13]. The DS model has been successfully modified in a number of ways [14-17] to cope with heat transfer and reactive transfer rates, etc. Furthermore, the basic ideas summarised above have also been confirmed on industrial converters by both Guthrie [I8] and Brimacombe [19]. Models have also been developed to predict the behaviour of the "chemical" component of some gas-liquid systems. However, one thing is clear; all gas-liquid reactive systems are governed by the degree to which effective mixing occurs. As such, the processes are dominated by the behaviour of the heat and mass exchange of the two phase fluid flow system. It is the pattern of movement of the turbulent liquid metal plus its interaction with the injected gas which must be predicted reliably, if sufficiently comprehensive comp-

Jan 1, 1984

By C R. Fountain, R J. Sinclair

The zinc industry is dominated by the electrolytic zinc (EZ) process. The EZ process has a low tolerance for impurities, resulting in tight concentrate specifications. Many mining companies sacrifice zinc recovery in order to meet smelter specifications. Some have ore-bodies that cannot be economically developed because too much metal has to be sacrificed, or it is just not possible to meet the specification. The BUKA Zinc Process (BZP) has been developed as a method of producing high-quality zinc from a wide range of concentrates. It can have lower capital and operating costs than the conventional zinc and lead production routes. Advantages accrue from increases in metal recovery during concentrating, smelting and refining; the elimination of most of the capital and operating costs associated with lead smelting; reduced transport costs; lower zinc refining costs; reduced refinery residue disposal costs; and reduced future environmental liabilities. This paper describes results of testwork that has been undertaken to demonstrate the viability of the BZP on both test rig and laboratory-bench scale.

Jan 1, 1998

By P. B. Lorenz

Wettability measurements and laboratory waterflood tests were compared under a wide variety of conditions. Experiments were conducted with synthetic and natural crude oils, treated and untreated outcrop and oilfield sandstone cores, and synthetic brines with and without caustic, detergent, or phosphate additives. Measurements were made on equilibrated and unequilibrated systems at 77° and 150° F. Wettability was evaluated by the Bureau of Mines method from capillary pressure curves determined with a centrifuge. The waterflood data were fitted by empirical curves; the parameters of the curves characterize primary and subordinate production and also give the ultimate oil recovery. Results showed that wettability measurements at 77° F were useful predictors of recovery efficiency in waterflood tests run at both temperatures. Oil recovery in the early stages of waterflooding increased with increasing water wettability; however, the ultimate recovery was highest at a slightly oil-wet condition. The oil displaced at highest speed in the centrifuge was correlated with ultimate recovery in waterflood tests. Chemical additives to the brine sometimes lowered wettability and also sometimes improved waterflood recovery, but wettability and recovery were not correlated with additives present. The effect of additives on recovery in waterflooding was best seen in water-oil ratio curves.

Jan 1, 1974

The movements of the major continental cratons and the distribution of the principal tectonostratigraphic terranes are reviewed in the Circum-Pacific region during Phanerozoic time. It is concluded that major periods of orogeny and consolidation of accreted terranes in the Circum-Pacific region is best correlated with periods of advance of cratonic blocks over the Pacific Ocean basin combined with relative convergent to transpressive motions between the cratons and the Pacific Ocean plates. Continental collisions and collision of terranes with continental margins has not been a significant geodynamic process in Circum-Pacific tectonic evolution. The permanency of the Pacific Ocean basin throughout 500 MA is remarkable. It appears no continental block or large continental fragment has ever entered or crossed the Pacific Ocean basin since early Paleozoic time. This area where no continent has entered for 500 MA is almost coincident with the present Pacific Ocean basin and seems associated with the 25 to 100 meter geoid high which dominates the present-day figure of the Earth.

Jan 1, 1990